These typos were found while reading the docs.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Remove alias 'efi' with invalid data.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add some documentation and a new flag so that we can safely enabled using
the ofnode interface to write to the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode only works with a single device tree, for the most part.
This is the control FDT used by U-Boot.
When booting an OS we may obtain a different device tree and want to
modify it. Add some initial support for this into the ofnode API.
Note that we don't permit aliases in this other device tree, since the
of_access implementation maintains a list of aliases collected at
start-up. Also, we don't need aliases to do fixups in the other FDT. So
make sure that flat tree and live tree processing are consistent in this
area.
Signed-off-by: Simon Glass <sjg@chromium.org>
The unflattening algorithm results in a single block of memory being
allocated for the whole tree. When writing new properties, these are
allocated new memory outside that block. When the block is freed, the
allocated properties remain.
Document how this works and the potential memory leak, as well as
mentioning that updating the livetree is actually supported now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a few links to documents about Verified Boot for Embedded (VBE).
These will be expanded as development proceeds.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not needed now that CONFIG_SYS_TARGET_NAME is correctly determined
when scanning Kconfig.
This reverts commit 25b8acee2e.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are a large number of options under CONFIG_SYS (but some of these
are elsewhere, spotted while cleaning CONFIG_SYS) that are never
referenced, or only used slightly later in the config file. Remove or
restructure these.
Signed-off-by: Tom Rini <trini@konsulko.com>
Start by describing in general the best practices for how to implement
configuration of some aspect of U-Boot. This generally means finding
the right choices for when something should be static or dynamically
configured and enabled. Then further document when to use CONFIG or CFG
namespaces for static configuration.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Describe exactly which bytes are hashed and in what order
when signing a configuration.
Signed-off-by: Martin Bonner <martingreybeard@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Start by elaborating on what some of our constraints tend to be with
image location values, and document where these external constraints
can come from. Provide a new subsection, an example based on the TI
ARMv7 OMAP2PLUS families of chips, that gives sample values and explains
why we use these particular values. This is based on what is in
include/configs/ti_armv7_common.h as of fb3ad9bd92 ("TI: Add, use a
DEFAULT_LINUX_BOOT_ENV environment string") as this contains just the
values referenced in this document now and not some of the further
additions that are less generic.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
start of test for fdt command
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmLgRtERHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYXFwgAlALOMj3bwwsIAXNa5j/hPb3j/ecIqXgn
ocyxN+U5eSb2Ju5Jc9QmSeUMnGrii9+PW9j0JApdHrbUgBI2Sx+zwqMTIfA+BS05
4xXZgk5jOT+we2489FjgFcplv+dIuVlsB/Zo6zTbZyjkobfilYsZEGYHJ/CYNaIH
n7EmZeby1cXL7DMCxT39d3hD43XSX8cqQ1IIiF9DgtHQYs2Ff8dFcbWArSdgLX3o
Eob2Qj/GjScg87zjZcsgZajWJMHUfMeD5ZiKN2fR0T/wOdO1WtzFoF2Mt8KZcW1j
BD1shgBCMSSl5EgRG1BQZw4Sa92W2IBlbJ9tfIh8qnWOzEBzOs/M6w==
=lsO4
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jul22' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm.git
minor dm- and fdt-related fixes
start of test for fdt command
When CONFIG_LOG is activated, if LOG_DEBUG is defined in a file and
DEBUG is not defined the trace with debug() macro are not displayed,
because the parameter cond : _DEBUG = 0 is checked in debug_cond().
With this patch the define DEBUG, used to force the trace generated by
debug() macro, is linked with the define LOG_DEBUG, used to force the
trace generated by other macros (log_debug, dev_dbg, pr_debug).
We only need to define LOG_DEBUG in a file to activate all the
traces generated by any U-Boot debug macro, as it is described in
/doc/develop/logging.rst
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add supporting new compatible string "u-boot,zynqmp-fpga-enc" to
handle loading encrypted bitfiles.
This feature requires encrypted FSBL, as according to UG1085:
"The CSU automatically locks out the AES key, stored in either BBRAM
or eFUSEs, as a key source to the AES engine if the FSBL is not
encrypted. This prevents using the BBRAM or eFUSE as the key source
to the AES engine during run-time applications."
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-14-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for Qualcomm QCS404 SoC based evaluation board.
Features:
- Qualcomm Snapdragon QCS404 SoC
- 1GiB RAM
- 8GiB eMMC, uSD slot
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/qcs404.rst.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Add support for 96Boards Dragonboard 845C aka Robotics RB3 development
platform. This board complies with 96Boards Open Platform Specifications.
Features:
- Qualcomm Snapdragon SDA845 SoC
- 4GiB RAM
- 64GiB UFS drive
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/sdm845.rst, board: dragonboard845c.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add instructions to build and boot from QSPI Flash
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
A common external watchdog circuit is kept alive by triggering a short
pulse on the reset pin. This patch adds support for this use case, while
making the algorithm configurable in the devicetree.
The "linux,wdt-gpio" driver being modified is based off the equivalent
driver in the Linux kernel, which provides support for this algorithm.
This patch brings parity to this driver, and is kept aligned with
the functionality and devicetree configuration in the kernel.
It should be noted that this adds a required property named 'hw_algo'
to the devicetree binding, following suit with the kernel. I'm happy to
make this backward-compatible if preferred.
Signed-off-by: Paul Doelle <paaull.git@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for hardware watchdog timer for Amlogic SoCs.
This driver has been heavily inspired by his Linux equivalent
(meson_gxbb_wdt.c).
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philippe Boos <pboos@baylibre.com>
Reviewed-by: Stefan Roese <sr@denx.de>
%s/formatted/format/
Fixes: 4211fb2ef6 ("doc: Migrate CodingStyle wiki page to Sphinx")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The wiki had gitdm-generated release statistics starting with v1.3.0.
Re-generate this information as Sphinx. This aims to be as historically
accurate as possible and so some company renames were kept to their old
rather than current name until we had made the switch previously.
Signed-off-by: Tom Rini <trini@konsulko.com>
For quite a long time we've been using a 3 week, rather than 2 week,
merge window as it was only 2 weeks during the timeframe where we did 2
month rather than 3 month releases. This corrects the places that still
had 2 weeks and tries to make things a bit clearer overall.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate the RelaseCycle wiki page to Sphinx. In terms of visible
changes, we stop having a dynamic countdown to when the release is. And
we drop the year-based statistics, that were not being kept up to date.
For the moment, we only link to statistics for v2022.07 but will add
back the historical data in a subsequent patch.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The "Workflow of a Custodian" section on the wiki had not been changed
in quite some time to reflect how the process has been functioning for
some time. First, update some links to point to modern and current
sources of information.
Second, and more overarching, reword much of the section. This expands
on the expectations of both custodians and developers when it comes to
rebasing patches. Rework the final points to be clearer that Custodians
are expected to do their best to test the changes and ask for help when
needed, as well as that pull requests are expected in a timely manner.
Cc: Claudius Heine <ch@denx.de>
Cc: Martin Bonner <martingreybeard@gmail.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Use gender-neutral language to refer to the user, consistently.
- Reword a few places so that they read more naturally.
- Make the long standing practice around "Twilight Time" more clear,
hopefully.
- Replace a reference to MAKEALL with a reference to CI testing as
that's the current requirement.
Cc: Claudius Heine <ch@denx.de>
Cc: Martin Bonner <martingreybeard@gmail.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Remove some missed wiki markup, and escape a "\n" correctly.
- Use gender-neutral language to refer to the user, consistently.
Cc: Claudius Heine <ch@denx.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the current Process wiki page to doc/develop/process.rst. The
changes here are for formatting or slight rewording so that it reads
well when linking to other Sphinx documents.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
For some time now we've allowed for '//' style comments, which mirrors
the Linux kernel. So drop this point here.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the current DesignPrinciples wiki page to
doc/develop/designprinciples.rst. The changes here are for formatting
or slight rewording so that it reads well when linking to other Sphinx
documents.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the current CodingStyle wiki page to doc/develop/codingstyle.rst.
The changes here are for formatting or slight rewording so that it reads
well when linking to other Sphinx documents.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The MT7621 requires external binary blob being executed during u-boot's
boot-up flow. It's necessary to provide a guide here for users to correctly
build the u-boot.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Our statistics pages have always been generated by gitdm. After
patching gitdm to generate an acceptable Sphinx output for tables,
include that and some other basic formatting here.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
- Explain why fdt_addr and initrd_addr should not be set to disable
relocation normally.
- Provide some advice on the typical loadaddr default value.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This variable is never set nor explained why it would be set, drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This tool seems a bit underloved. Unfortunately, it seems to be missing
support for FIT images. Alas...
Add a man page documenting it. The example is taken from commit a804b5ce2d
("Add dumpimage, a tool to extract data from U-Boot images").
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Despite the original description of these options, they are not always
image names, or even files. Some image types use these options to convey
configuration directly. Re-document these options as configuration options.
Additionally, add a new section documenting the format of the configuration
for each image type which uses it. In general, if configuration is used
directly (without a separate file) I have added documentation for it. If
the configuration points to a separate file, I have referenced that file's
documentation. Where there is no such documentation, I have added it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The mkimage command has had many options added over the years.
Unfortunately, we are starting to run out of short options. Recent options
don't have any obvious relation to their meaning (e.g. -o/-g). Fortunately,
long options exist. Add long options for each current short option.
For the curious, the remaining short options are HIkLmMPQSuUwWXyYzZ.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Per man-pages(7), "use of an AUTHORS section is strongly discouraged."
Remove it, and instead add some copyright notices and an SPDX. The default
license for U-Boot is GPL2, so that's what I put. The copyright dates are
based on the commit dates.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a SEE ALSO section to link to similar man pages, as well as to
the U-Boot documentation.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In leiu of a non-standard HOMEPAGE section, add a BUGS section with a link
to the issue tracker.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This makes a variety of changes for the options to make them
typographically consistent, clarify their meaning, and fix grammatical (or
other) errors. Many of the changes here are stylistic, though there are a
few fixes. The main changes I made across the board were:
- All options are bolded and parameters italicised
- All single quotes are properly matched (instead of using apostrophes)
- Minor background info has been added to clarify many underdocumented
options
- Default values for options are documented
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The description in NAME should not be capitalized. Fix a grammatical error
as well.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This moves some options which work in any mode to the general options
section. -p is moved to after -E/-B since those options are related. This
also adds documentation for -h and -V.
The -F, -l, and -G options are documented twice. Remove the second
documentation in each case. The synopsis for -l also suggests an implied
second uimage-file-name parameter. E.g.
mkimage [-l uimage-file-name] uimage-file-name
This is misleading, so remove it. Wrap a few lines to 80 characters as
well.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The options are divided up into several subsections. Use the appropriate
macro. While we're at it, rename the headings to better reflect the
contents of their sections.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Square brackets are commonly used to denote optional parts of a command.
However, all option arguments are mandatory. Remove these brackets. This
also removes some unnecessary quotation marks, and uses hyphens to connect
words in option arguments. This is intended to just clean up the
formatting, leaving content corrections to later patches.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This puts each example in a new paragraph and uses a hanging indent for
continued lines to increase clarity. We use tabs instead of .in or .RS for
the indent because it renders properly in both man and mandoc (which is
what many common HTML man pages use). The only nit is that the tab stops in
man default to something like 2", so reduce that to 1". We also escape
every "minus" as recommended by man-pages(7).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Blank lines do not have well-defined semantics in fill mode (the default).
Instead, use empty requests (.) where vertical space is necessary for
readability. There are a few places where we use a paragraph instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The synopsis section is a bit messy. As an example, "uimage file name" is
printed in italics, bold, and roman (depending on the line). This cleans
things up and converts the synopsis section to use standard style. The
.SY/.YS macros set up appropriate formatting for command synopsis sections
(such as disabling hyphenation and setting a hanging indent). All parts of
the synopsis now use the following style:
- Bold for parts of the command which should be typed in by the user (such
as the program name and flags)
- Italic for parts which should be replaced (such as uimage-file-name)
- Roman for parts which should not be typed at all (such as brackets)
Multi-word variables now use hyphens to connect their words instead of
spaces. This makes it clearer that all the words are part of the same
variable. Additionally, "option ..." is used to denote where other options
may be specified, as this appears to be standard style.
In addition to the above style changes, this also makes some changes to
content. The use of the term "legacy" has been removed, since this simply
refers to any non-FIT image type. Additionally, wording like "uimage file
name" has been replaced with "image-file-name" to better reflect that
images may or may not be uImages. Lastly, the "auto" value for -f is
documented in the synopsis.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a "secure" version of STM32 boards based on SCMI when RCC_TZCR.TZEN=1.
Only boards provided by STMicroelectronics are concerned:
-STM32MP157A-DK1
-STM32MP157C-DK2
-STM32MP157C-ED1
-STM32MP157C-EV1
The resources secured by RCC_TZCR.TZEN=1 are managed by OP-TEE
and the associated SCMI services, reset and clock.
These device trees are only supported with stm32mp15_defconfig,
with OP-TEE, SCMI and without SPL support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
With the last platform for this architecture removed, remove the rest of
the architecture support as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At this point, the only user of ohci-hcd that also uses PCI is using DM,
so we can drop CONFIG_PCI_OHCI* usage. No platforms set either of
CONFIG_SYS_USB_OHCI_BOARD_INIT or CONFIG_SYS_USB_OHCI_CPU_INIT so those
hooks can be removed as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is a preliminary documentation introducing different
boot sequences, and notably the recovery mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20220706093649.3261229-1-narmstrong@baylibre.com
Add a comment explaining the design goals of bloblist, to make it easier
for people to understand and comment on the structure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename the sections used to implement linker lists so they begin with
'__u_boot_list' rather than '.u_boot_list'. The double underscore at the
start is still distinct from the single underscore used by the symbol
names.
Having a '.' in the section names conflicts with clang's ASAN
instrumentation which tries to add redzones between the linker list
elements, causing expected accesses to fail. However, clang doesn't try
to add redzones to user sections, which are names with all alphanumeric
and underscore characters.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
cp.b is used a lot as a way to load binaries to memory and execute
them, however we may need to integrate this with the efi subsystem to
set it up as a bootdev.
So, introduce a loadm command that will be consistent with the other
loadX commands and will call the efi API's.
ex: loadm $kernel_addr $kernel_addr_r $kernel_size
with this a kernel with CONFIG_EFI_STUB enabled will be loaded and
then subsequently booted with bootefi command.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add in U-Boot documentation the quick instruction to
setup the STMicroelectronics STM32MP13x boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support for new compatible "st,stm32mp13-ddr" to manage the
DDR sub system (Controller and PHY) in STM32MP13x SOC:
- only one AXI port
- support of 16 port output (MEMC_DRAM_DATA_WIDTH = 2)
The STM32MP15x SOC have 2 AXI ports and 32 bits support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This adds support for "nvmem cells" as seen in Linux. The nvmem device
class in Linux is used for various assorted ROMs and EEPROMs. In this
sense, it is similar to UCLASS_MISC, but also includes
UCLASS_I2C_EEPROM, UCLASS_RTC, and UCLASS_MTD. New drivers corresponding
to a Linux-style nvmem device should be implemented as one of the
previously-mentioned uclasses. The nvmem API acts as a compatibility
layer to adapt the (slightly different) APIs of these uclasses. It also
handles the lookup of nvmem cells.
While nvmem devices can be accessed directly, they are most often used
by reading/writing contiguous values called "cells". Cells typically
hold information like calibration, versions, or configuration (such as
mac addresses).
nvmem devices can specify "cells" in their device tree:
qfprom: eeprom@700000 {
#address-cells = <1>;
#size-cells = <1>;
reg = <0x00700000 0x100000>;
/* ... */
tsens_calibration: calib@404 {
reg = <0x404 0x10>;
};
};
which can then be referenced like:
tsens {
/* ... */
nvmem-cells = <&tsens_calibration>;
nvmem-cell-names = "calibration";
};
The tsens driver could then read the calibration value like:
struct nvmem_cell cal_cell;
u8 cal[16];
nvmem_cell_get_by_name(dev, "calibration", &cal_cell);
nvmem_cell_read(&cal_cell, cal, sizeof(cal));
Because nvmem devices are not all of the same uclass, supported uclasses
must register a nvmem_interface struct. This allows CONFIG_NVMEM to be
enabled without depending on specific uclasses. At the moment,
nvmem_interface is very bare-bones, and assumes that no initialization
is necessary. However, this could be amended in the future.
Although I2C_EEPROM and MISC are quite similar (and could likely be
unified), they present different read/write function signatures. To
abstract over this, NVMEM uses the same read/write signature as Linux.
In particular, short read/writes are not allowed, which is allowed by
MISC.
The functionality implemented by nvmem cells is very similar to that
provided by i2c_eeprom_partition. "fixed-partition"s for eeproms does
not seem to have made its way into Linux or into any device tree other
than sandbox. It is possible that with the introduction of this API it
would be possible to remove it.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds support for signing images in auto-generated FITs. To do this,
we need to add a signature node. The algorithm name property already has
its own option, but we need one for the key name hint. We could have
gone the -G route and added an explicit name for the public key (like
what is done for the private key). However, many places assume the
public key can be constructed from the key dir and hint, and I don't
want to do the refactoring necessary.
As a consequence of this, it is now easier to add public keys to an
existing image without signing something. This could be done all along,
but now you don't have to create an its just to do it. Ideally, we
wouldn't create a FIT at the end. This could be done by calling
fit_image_setup_sig/info.crypto->add_verify_data directly.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Document -G and the secondary image types which can be used with -R.
Also reword the documentation of -s for clarity.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
The actual support was added in commit fec8c900c8 ("power: regulator:
Add support for regulator-force-boot-off"), update the docs to include
this.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Update the Kconfig entry to have the correct defaults for i.MX7
platforms, and move the existing large comment from imx7_spl.h to
doc/imx/common/imx7.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the Kconfig entry to have the correct defaults for i.MX6
platforms, and move the existing large comment from imx6_spl.h to
doc/imx/common/imx6.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_SYS_MALLOC_SIMPLE
The problem here is that a few platforms have been doing:
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif
instead of defining CONFIG_SPL_SYS_MALLOC_SIMPLE directly. Correct this
and update the documentation in a few places to match usage.
Signed-off-by: Tom Rini <trini@konsulko.com>
The OsIndications is a 64 bit variable, and the current code expects
the value of the variable to be 64 bit. Update the documentation to
reflect this fact.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
"valu" should be "value".
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The firmware management protocol can be used to manage device firmware.
U-Boot can be configured to provide an implementation.
Document the related functions in the API section.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
For indicating the address and size of a memory region other commands use a
<addr>[:<size>] syntax. Do the same for bootefi.
Fixes: 2058983689 ("cmd: bootefi: restore ability to boot arbitrary blob")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This documents some additional options which can be used with valgrind, as
well as directions for future work. It also fixes up inline literals to
actually be inline literals (and not italics). The content of this
documentation is primarily adapted from [1].
[1] https://lore.kernel.org/u-boot/57cb4b49-fa30-1194-9ac3-faa53e8033bd@gmail.com/
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The following Python packages are used by U-Boot, too:
* python3-asteval
* python3-subunit
* python3-testtools
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Image created by LTO is not friendly to debugger, let's document this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Mention CONFIG_CC_OPTIMIZE_FOR_DEBUG and LLDB.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
It should be CONFIG_SANDBOX_RAM_SIZE_MB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Set kernel_comp_addr_r and kernel_comp_size for compressed kernel.
Adjust existing addresses for ramdisk, so that kernel_comp_addr_r
comes before the ramdisk image, since the decompressed kernel size
is known to us. This way we can allow big ramdisk image to be loaded.
Update unleashed.rst to remove the manual environment configuration
for compressed kernel boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
-----BEGIN PGP SIGNATURE-----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=s7xn
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
Over the years, several options have not made it into the help message.
Document them. Do the same for the man page.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
%s/cammand/command/
%s/sequencies/sequences/
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add an initial VPL build for sandbox. This includes the flow:
TPL (with of-platdata) -> VPL -> SPL -> U-Boot
To run it:
./tpl/u-boot-tpl -D
The -D is needed to get the default device tree, which includes the serial
console info.
Add a Makefile check for OF_HOSTFILE which is the option that enables
devicetree control on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for VPL, a new phase of U-Boot. This runs after TPL. It is
responsible for selecting which SPL binary to run, based on a
verified-boot process.
Signed-off-by: Simon Glass <sjg@chromium.org>
The '--args' parameter to gdb comes before the binary that the debugger
will be attached to rather than after the binary and before the
arguments. Fix that in the docs.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The real entry point is _start_e500. There is no _start symbol at all. So
rename _start_e500 to _start for convension that _start symbol is used as
entry point.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As removal of nds32 has been ack'd for the Linux kernel, remove support
here as well.
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
To quote the author:
The bootflow feature provide a built-in way for U-Boot to automatically
boot an Operating System without custom scripting and other customisation.
This is called 'standard boot' since it provides a standard way for
U-Boot to boot a distro, without scripting.
It introduces the following concepts:
- bootdev - a device which can hold a distro
- bootmeth - a method to scan a bootdev to find bootflows (owned by
U-Boot)
- bootflow - a description of how to boot (owned by the distro)
This series provides an implementation of these, enabled to scan for
bootflows from MMC, USB and Ethernet. It supports the existing distro
boot as well as the EFI loader flow (bootefi/bootmgr). It works
similiarly to the existing script-based approach, but is native to
U-Boot.
With this we can boot on a Raspberry Pi 3 with just one command:
bootflow scan -lb
which means to scan, listing (-l) each bootflow and trying to boot each
one (-b). The final patch shows this.
With a standard way to identify boot devices, booting become easier. It
also should be possible to support U-Boot scripts, for backwards
compatibility only.
...
The design is described in these two documents:
https://drive.google.com/file/d/1ggW0KJpUOR__vBkj3l61L2dav4ZkNC12/view?usp=sharinghttps://drive.google.com/file/d/1kTrflO9vvGlKp-ZH_jlgb9TY3WYG6FF9/view?usp=sharing
A 'bootdev' is a device which can be used to boot an operating system.
It is a child of the media device (e.g. MMC) which handles reading files
from that device, such as a bootflow file.
Add a uclass for bootdev and the various helpers needed to make it
work. Also add a binding file, empty for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
The 'bootstd' device provides the central information about U-Boot
standard boot.
Add a uclass for bootstd and the various helpers needed to make it
work. Also add a binding file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some basic stuff about tag support is explained under
doc/devlop/driver-model.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
A image_size parameter has been added to the bootefi parameter.
Describe all parameters.
Correct how the description of how the device-path in the loaded
image protocol is determined.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Adds simple documentation about common properties for watchdog
in the device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The imx8mn_evk target have been converted to use binman.
With the binman approach the ATF load address is described via
devicetree, so remove the now unneeded instruction of exporting
ATF_LOAD_ADDR.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Allow device tree to provide ti,ddr-freq0 to be used as the initial DDR
frequency that is set for lpddr4 before initialization of the
controller. Make this optional and continue to use PLL bypass frequency
as is done currently if ti,ddr-freq0 is not provided.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Add rk3066 Rikomagic MK808 to the list of
mainline supported Rockchip boards.
Include instructions for creating and programming
images to NAND and SD card.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There are several PX30/RK3326 boards in use without
mentioning in rockchip.rst. Add boards and examples.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With more text coming to the rockchip.rst document,
give it a restyle first.
Changed:
sort build examples alphabetically
add git clone example
fix bash examples
fix phrases (grammer)
fix typos
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.
[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]
Update the capsule update functionality related documentation to
refect the additional definitions that need to be made per platform
for supporting the capsule update feature.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
While building a capsule, the GUID value of that specific image is to
be passed through the --guid command option to the mkeficapsule
tool instead of using one of --raw or --fit options, where the GUID
value passed through the command line option is the image GUID.
This renders the EFI_FIRMWARE_IMAGE_TYPE_UBOOT_FIT_GUID and
EFI_FIRMWARE_IMAGE_TYPE_UBOOT_RAW_GUID values superfluous. Remove the
--raw and --fit command line options as well. Also modify the
mkeficapsule man page to reflect this change.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Add a driver which allows to use of LEDs connected
to PWM (Linux compatible).
MAINTAINERS: add i.vozvakhov as a maintainer of leds-pwm
C(required during new functionality adding).
Signed-off-by: Ivan Vozvakhov <i.vozvakhov@corp.mail.ru>
This documents how to get more detailed results from valgrind made possible
by the last two commits.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide settings for enabling the debug UART of the virt machine on
RISC-V QEMU.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* add link to booti man-page
* correct link description for efidebug command
* correct punctuation
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This is an attempt to cover the common cases found when enabling driver
model for serial on a new board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Drop this text at the end since it already mentions bootp and dhcp.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This doesn't really make much sense in the documentation. Add a code
comment instead.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
U-boot is intended to replace linux kernel in android boot image(ABL), and
it's FIT payload to replace initramfs file. The boot process is similar to
boot image with linux:
- android bootloader (ABL) unpacks android boot image
- ABL sets `linux,initrd-start property` in chosen node in unpacked FDT
- ABL sets x0 register to FDT address, and passes control to u-boot
- u-boot reads x0 register, and stores it in `prevbl_fdt_addr` env variable
- u-boot reads `linux,initrd-start` property,
and stores it in `prevbl_initrd_start_addr`
In this way, u-boot bootcmd relies on `prevbl_initrd_start_addr` env
variable, and boils down to `bootm $prevbl_initrd_start_addr`.
If more control on boot process is desired, pack a boot script in
FIT image, and put it to default configuration
What done:
- Rearrange defconfig option order
- Add CONFIG_SAVE_PREV_BL_* options
- Doc updates:
- remove wrong SBOOT memory corruption note, because
memory is changed during u-boot bringup process,
not by SBOOT
- put payload on ramdisk place in abl boot image
creation step
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
U-boot is intended to replace linux kernel in android boot image(ABL), and
it's FIT payload to replace initramfs file. The boot process is similar to
boot image with linux:
- android bootloader (ABL) unpacks android boot image
- ABL sets `linux,initrd-start property` in chosen node in unpacked FDT
- ABL sets x0 register to FDT address, and passes control to u-boot
- u-boot reads x0 register, and stores it in `prevbl_fdt_addr` env variable
- u-boot reads `linux,initrd-start` property,
and stores it in `prevbl_initrd_start_addr`
In this way, u-boot bootcmd relies on `prevbl_initrd_start_addr` env
variable, and boils down to `bootm $prevbl_initrd_start_addr`.
If more control on boot process is desired, pack a boot script in
FIT image, and put it to default configuration
What done:
- strip unneeded config options
- add FIT image support
- add framebuffer node, u-boot logo and video console
- increase LMB_MAX_REGIONS, to store all linux dtb reserved memory regions
- add linux kernel image header
Uart driver causes hang, when u-boot is used in android boot image instead
of linux. Temporary disable console driver, until investigated and fixed.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Unfortunately, we require additional logic to buildman to support this
removal and still use SYS_SOC, etc, for build targets.
This reverts commit eeec00072d.
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds support for booting entirely from JTAG while using a
hard-coded RCW. With these steps, it is not necessary to program a
"good" RCW using CodeWarrior. The method here can be performed with any
JTAG adapter supported by OpenOCD, including the on-board CMSIS-DAP
(albeit very slowly).
These steps require LS1046A support in OpenOCD, which was added in [1].
[1] 5b70c1f679/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
[trini: Add reference to doc/board/nxp/ls1046ardb.rst]
This documents how to use semihosting, the new semihosting features, and
how to migrate from smhload.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds some instructions for enabling the debug uart, including the
correct address and clock rate.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds some additional info about booting from different sources,
including the correct switch positions.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This converts the readme for this board to rST. I have tried not to
change any semantics from the original (though I did convert MB to M).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This converts the semihosting readme to rST. I have tried to make only
cosmetic changes, but I did fix up the first link (which was broken).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
The ARMv8-R64 architecture introduces optional VMSA (paging based MMU)
support in the EL1/0 translation regime, which makes that part mostly
compatible to ARMv8-A.
Add a new board variant to describe the "BASE-R64" FVP model, which
inherits a lot from the existing v8-A FVP support. One major difference
is that the memory map in "inverted": DRAM starts at 0x0, MMIO is at
2GB [1].
* Create new TARGET_VEXPRESS64_BASER_FVP target, sharing most of the
exising configuration.
* Implement inverted memory map in vexpress_aemv8.h
* Create vexpress_aemv8r defconfig
* Provide an MMU memory map for the BASER_FVP
* Update vexpress64 documentation
At the moment the boot-wrapper is the only supported secure firmware. As
there is no official DT for the board yet, we rely on it being supplied
by the boot-wrapper into U-Boot, so use OF_HAS_PRIOR_STAGE, and go with
a dummy DT for now.
[1] https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[Andre: rebase and add Linux kernel header]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[trini: Add MAINTAINERS entry for Peter]
This converts the existing README.plan9 to reST, and puts it under
the doc/usage/os directory.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
At present the doc only mentions Arm, PowerPC and x86. RISC-V support
has been added since VxWorks SR0650 support for a while, and U-Boot
supports loading a RISC-V VxWorks kernel too. Let's document it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This converts the existing README.vxworks to reST, and puts it under
the doc/usage/os directory.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Update the extension command title for consistency with other commands.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Currently all shell command docs are put in the doc/usage root.
Let's group them into cmd/ sub-directory.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Provide human readable descriptions of the speed nodes instead of the name
of constants from the code as it is already done for 'mmc rescan'
command in commit 212f078496 ("doc: mmc rescan speed mode").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The non-driver model video support was removed two years ago. Drop this
driver, which is only used by nokia_rx51.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add documentation about the different configuration files for the
RaspberryPi board family.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
There is no CONFIG_UEFI_SECURE_BOOT, and there was never any.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add section how to run U-Boot in n900 qemu machine.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
It add documentation on licencing & provides links to the amlogic-boot-fip
pre-built files collections.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
With all boards now using DM_ETH we determine the value for
CONFIG_FEC_XCV_TYPE at run time, except in the case of the default
fall-back. Set the fallback directly now.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for Kevin, an RK3399-based convertible chromebook that is
very similar to Bob. This patch is mostly based on existing support for
Bob, with only minor changes for Kevin-specific things.
Unlike other Gru boards, coreboot sets Kevin's center logic to 925 mV,
so adjust it here in the dts as well. The rk3399-gru-kevin devicetree
has an unknown event code reference which has to be defined, set it
to the Linux counterpart. The new defconfig is copied from Bob with the
diffconfig:
DEFAULT_DEVICE_TREE "rk3399-gru-bob" -> "rk3399-gru-kevin"
DEFAULT_FDT_FILE "rockchip/rk3399-gru-bob.dtb" -> "rockchip/rk3399-gru-kevin.dtb"
VIDEO_ROCKCHIP_MAX_XRES 1280 -> 2400
VIDEO_ROCKCHIP_MAX_YRES 800 -> 1600
+TARGET_CHROMEBOOK_KEVIN y
With this Kevin can boot from SPI flash to a usable U-Boot prompt on the
display with the keyboard working, but cannot boot into Linux for
unknown reasons.
eMMC starts in a working state but fails to re-init, microSD card works
but at a lower-than-expected speed, USB works but causes a hang on
de-init. There are known workarounds to solve eMMC and USB issues.
Cc: Marty E. Plummer <hanetzer@startmail.com>
Cc: Simon Glass <sjg@chromium.org>
[Alper: commit message, resync config with Bob, update MAINTAINERS,
add to Rockchip doc, add Kconfig help message, set regulator]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
"kendryte" is the marketing name for the K210 RISC-V SoC produced by
Canaan Inc. Rather than "kendryte,k210", use the usual "canaan,k210"
vendor,SoC compatibility string format in the device tree files and
use the SoC name for file names.
With these changes, the device tree files are more in sync with the
Linux kernel DTS and drivers, making uboot device tree usable by the
kernel.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Testes proved that current kwboot version supports also Avanta SoCs.
It looks like that Avanta SoCs are using same kwbimage format as Armada.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Document -D, -b, -d, -q and -s options.
Add common examples how to use kwboot.
Add information about Armada 38x BootROM bug for debug console mode and how
to workaround it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Changes SCMI bindings documentation to relate to Linux kernel
source tree that recently changed the bindings description to YAML
format.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Currently -l option for mkimage and dumpimage ignores option -T and always
tries to autodetect image type.
With this change it is possible to tell mkimage and dumpimage to parse
image file as specific type (and not random autodetected type). This allows
to use mkimage -l or dumpimage -l as tool for validating image.
params.type for -l option is now by default initialized to zero
(IH_TYPE_INVALID) instead of IH_TYPE_KERNEL. imagetool_get_type() for
IH_TYPE_INVALID returns NULL, which is assigned to tparams. mkimage and
dumpimage code is extended to handle tparams with NULL for -l option. And
imagetool_verify_print_header() is extended to do validation via tparams if
is not NULL.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
They are no longer needed, because we now have proper driver support for
the sl28cpld management controller.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has an internal watchdog which supervises the board startup.
Although, the initial state of the watchdog is configurable, it is
enabled by default. In board_late_init(), which means almost everything
worked as expected, disable the watchdog.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The watchdog timer is part of the sl28cpld management controller. The
watchdog timer usually supervises the bootloader boot-up and if it bites
the failsafe bootloader will be activated. Apart from that it supports
the usual board level reset and one SMARC speciality: driving the
WDT_TIMEOUT# signal.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
SMBIOS is not x86 specific. So we should have an architecture independent
page describing it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This converts the existing driver API docs (clk-uclass.h) to kernel doc
format and adds them to the HTML documentation. Because the kernel doc
sphinx converter does not handle functions in structs very well, the
individual methods are documented separately. This is primarily inspired by
the phylink documentation [1], which uses this trick extensively.
[1] https://www.kernel.org/doc/html/latest/networking/kapi.html#c.phylink_mac_ops
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20211222171114.3091780-5-seanga2@gmail.com
This converts the existing client (aka clk.h) documentation to kernel doc
format, and adds it to the HTML docs. I have tried to preserve existing
comments as much as possible, refraining from semantic changes.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20211222171114.3091780-4-seanga2@gmail.com
[rebased onto u-boot/master and resolved conflicts]
Signed-off-by: Sean Anderson <seanga2@gmail.com>
U-Boot now supports NVMe storage and on the laptop models, the
SPI keyboard. Since we now disable the debug console by default
provide instructions on how the enable the debug console including
a table listing the appropriate UART base address for each of the
supported SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Documentation:
* mkeficapsule man-page
UEFI changes:
* add support for signing images to mkeficapsule
* add support for user define capsule GUID
* adjust unit tests for capsules
* fix UEFI image signature validation in case of multiple signatures
-----BEGIN PGP SIGNATURE-----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=AAdJ
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-04-rc2-4' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc2-4
Documentation:
* mkeficapsule man-page
UEFI changes:
* add support for signing images to mkeficapsule
* add support for user define capsule GUID
* adjust unit tests for capsules
* fix UEFI image signature validation in case of multiple signatures
The existing options, "--fit" and "--raw," are only used to put a proper
GUID in a capsule header, where GUID identifies a particular FMP (Firmware
Management Protocol) driver which then would handle the firmware binary in
a capsule. In fact, mkeficapsule does the exact same job in creating
a capsule file whatever the firmware binary type is.
To prepare for the future extension, the command syntax will be a bit
modified to allow users to specify arbitrary GUID for their own FMP driver.
OLD:
[--fit <image> | --raw <image>] <capsule file>
NEW:
[--fit | --raw | --guid <guid-string>] <image> <capsule file>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now we can use mkeficapsule command instead of EDK-II's script
to create a signed capsule file. So update the instruction for
capsule authentication.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add a man page for mkeficapsule command.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Fix some typo and wrong information about dfu_alt_info.
- Add the parameter format, decimal only or hexadecimal.
- Use same parameter name for the same kind of parameters.
(e.g. dev -> dev_id)
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Addresses the feedback provided on 5902a397d0 ("mkimage: Allow to
specify the signature algorithm on the command line") which raced with
the merge.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
this will add kaslrseed keyword to sysboot lable,
when it set, it will request to genarate random number
from hwrng as kaslr-seed.
with this patch exlinux.conf label looks like
label l0
menu testing
linux /boot/vmlinuz-5.15.16-arm
initrd /boot/initramfs-5.15.16-arm.img
fdtdir /boot/dtbs/5.15.16-arm/
kaslrseed
append root=UUID=92ae1e50-eeeb-4c5b-8939-7e1cd6cfb059 ro
Tested on Khadas VIM with kernel 5.16.0-rc5-arm64, Debian 11.
Signed-off-by: Zhang Ning <zhangn1985@qq.com>
Apple SoCs have an integrated NVMe controller that isn't connected
over a PCIe bus. In preparation for adding support for this NVMe
controller, split out the PCI support into its own file. This file
is selected through a new CONFIG_NVME_PCI Kconfig option, so do
a wholesale replacement of CONFIG_NVME with CONFIG_NVME_PCI.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
We can now use same U-Boot images on both QEMU virt machine and QEMU
spike machine so let's update the QEMU RISC-V documentation.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
As suggested in commit 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") for imx8mm_evk, it is possible to produce
single bootable image via binman. This restores the original behavior in
distros, where only one boot container is used to create target image.
Perform similar adaptions in order to provide single bootable image for
imx8mn-ddr4-evk derivate.
Update documentation to drop additional step of copying u-boot.itb
Fixes: 353dfe4b43 ("imx8mn-ddr4-evk: switch to use binman")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
imx8mm-u-boot.dtsi passes the ATF load address via the
'entry' and 'load' properties.
Remove the step that performs the ATF_LOAD_ADDR export, which is
now unneeded.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
imx8mm-u-boot.dtsi passes the ATF load address via the
'entry' and 'load' properties.
Remove the step that performs the ATF_LOAD_ADDR export, which is
now unneeded.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
imx8mm-u-boot.dtsi passes the ATF load address via the
'entry' and 'load' properties.
Remove the step that performs the ATF_LOAD_ADDR export, which is
now unneeded.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
This resyncs us with the version found in v5.16 of the Linux kernel with
the following exceptions:
- Keep our u-boot specific tests / code area.
- Change the location of checkpatch.rst
- Drop the "use strscpy" test as we don't have that, but do have strlcpy
and want that used now.
- Keep debug/printf in the list for $logFunctions
This also syncs the spdxcheck.py tool and all the associated
documentation.
S
Signed-off-by: Simon Glass <sjg@chromium.org>
Documentation:
* update Nokia RX-51 documentation and move it to rst
* describe boot switch settings for HiFive Unmatched board
UEFI:
* fix the checking of images hashes and signatures
* provide the RISCV_EFI_BOOT_PROTOCOL
-----BEGIN PGP SIGNATURE-----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=+edp
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-04-rc1-3' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc1-3
Documentation:
* update Nokia RX-51 documentation and move it to rst
* describe boot switch settings for HiFive Unmatched board
UEFI:
* fix the checking of images hashes and signatures
* provide the RISCV_EFI_BOOT_PROTOCOL
unmatched.rst describes booting from SD card or from SPI. But only for
booting from SPI the boot selection settings are described.
Add the missing information.
Fix a typo 'uSD'.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This change contains update for doc/README.nokia_rx51 documentation file
with information how to load U-Boot image to device RAM without need to
flash it and also how to flash it into OneNAND via 0xFFFF flasher.
Signed-off-by: Pali Rohár <pali@kernel.org>
Since commit 25c5b65178 ("Nokia RX-51: Do not try calling both ext2load
and ext4load") command ext4load is used for all ext2/3/4 fs variants.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This probably should have been done a while back since it is a core
system. Very few boards remain to be migrated.
Addd a migration deadline for a year out.
Signed-off-by: Simon Glass <sjg@chromium.org>
The build system already automatically looks for and includes an
in-tree *-u-boot.dtsi when building the control .dtb. However, there
are some things that are awkward to maintain in such an in-tree file,
most notably the metadata associated to public keys used for verified
boot.
The only "official" API to get that metadata into the .dtb is via
mkimage, as a side effect of building an actual signed image. But
there are multiple problems with that. First of all, the final U-Boot
(be it U-Boot proper or an SPL) image is built based on a binary
image, the .dtb, and possibly some other binary artifacts. So
modifying the .dtb after the build requires the meta-buildsystem
(Yocto, buildroot, whatnot) to know about and repeat some of the steps
that are already known to and handled by U-Boot's build system,
resulting in needless duplication of code. It's also somewhat annoying
and inconsistent to have a .dtb file in the build folder which is not
generated by the command listed in the corresponding .cmd file (that
of course applies to any generated file).
So the contents of the /signature node really needs to be baked into
the .dtb file when it is first created, which means providing the
relevant data in the form of a .dtsi file. One could in theory put
that data into the *-u-boot.dtsi file, but it's more convenient to be
able to provide it externally: For example, when developing for a
customer, it's common to use a set of dummy keys for development,
while the consultants do not (and should not) have access to the
actual keys used in production. For such a setup, it's easier if the
keys used are chosen via the meta-buildsystem and the path(s) patched
in during the configure step. And of course, nothing prevents anybody
from having DEVICE_TREE_INCLUDES point at files maintained in git, or
for that matter from including the public key metadata in the
*-u-boot.dtsi directly and ignore this feature.
There are other uses for this, e.g. in combination with ENV_IMPORT_FDT
it can be used for providing the contents of the /config/environment
node, so I don't want to tie this exclusively to use for verified
boot.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Fix doc formatting error (make htmldocs)
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to find out which boards define a particular
option, or combination of options. This is not as easy as grepping the
defconfig files since many options are implied by others.
Add a -f option to the moveconfig tool to permit this. Update the
documentation to cover this, including a better title for the doc page.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the Python code in U-Boot is somewhat inconsistent, with some
files passing pylint quite cleanly and others not.
Add a way to track progress on this clean-up, by checking that no module
has got any worse as a result of changes.
This can be used with 'make pylint'.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Re-generate pylint.base]
This permits to prepare FIT image description that do not hard-code the
final choice of the signature algorithm, possibly requiring the user to
patch the sources.
When -o <algo> is specified, this information is used in favor of the
'algo' property in the signature node. Furthermore, that property is set
accordingly when writing the image.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Documentation:
* describe printf() format codes
UEFI
* enable more algorithms for UEFI image verification, e.g. SHA256-RSA2048
General
* simplify printing short texts for GUIDs
* provide a unit test for printing GUIDs
-----BEGIN PGP SIGNATURE-----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=GoR6
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-04-rc1-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc1-2
Documentation:
* describe printf() format codes
UEFI
* enable more algorithms for UEFI image verification, e.g. SHA256-RSA2048
General
* simplify printing short texts for GUIDs
* provide a unit test for printing GUIDs
Commit 98f705c9ce ("powerpc: remove 4xx support") removed (in 2017) the
last code that made use of bedbug debugger support. Since there aren't
any boards left that define either CONFIG_CMD_BEDBUG or a real
bedbug_init(), drop this feature from u-boot.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This will allow consumers to choose a pxe label at runtime instead of
having to prompt the user. One good use-case for this, is choosing
whether or not to apply a dtbo depending on the hardware configuration.
e.g: for TI's AM335x EVM, it would be convenient to apply a particular
dtbo only when the J9 jumper is on PRUSS mode. To achieve this, the
pxe menu should have 2 labels, one with the dtbo and the other without,
then the "pxe_label_override" env variable should point to the label with
the dtbo at runtime only when the jumper is on PRUSS mode.
This change can be used for different use-cases and bring more
flexibilty to consumers who use sysboot/pxe_utils.
if "pxe_label_override" is set but does not exist in the pxe menu,
the code should fallback to the default label if given, and no failure
is returned but rather a warning message.
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Correct Sphinx style comments in include/dm/fdtaddr.h
and add the devfdt API to the HTML documentation;
these functions are NOT compatible with live tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/ofnode.h
and add the device tree node API to the HTML documentation;
the ofnode functions are compatible with Live tree or with flat
device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/read.h
and add the device read from device tree API to the HTML
documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/devres.h
and add the driver model device resource API, devres_*(),
to the HTML documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/device.h
and add the driver model device API to the HTML documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/platdata.h
and add the associated API to the HTML documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/lists.h
and add the list API to the HTML documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/devres.h
and add the associated driver model API to the HTML documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/uclass.h
and add the driver model UCLASS API to the HTML documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The Juno Arm development board is an open, vendor-neutral, Armv8-A
development platform.
Add documentation that briefly outlines the hardware, and describes
building and installation of U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
FIx up various minor errors and add the API documentation to the bloblist
docs, since it is quite useful to see it in the same place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Model names are SM-A{3,5,7}20, just SM-{3,5,7}20 could also refer to
SM-J{3,5,7}20 or SM-T{3,5,7}20.
Fixes: 3e2095e960 ("board: samsung: add support for Galaxy A series
of 2017 (a5y17lte)")
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Some boards still use the old timer mechanism. Set a deadline for them to
update to driver model. Point to some examples as well.
This needs a bit of a strange rule to avoid an error on some boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----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=dLEg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
All i.MX8MQ boards have been converted to binman, which makes it
necessary to flash both flash.bin and u-boot.itb to get a bootable
system. Prior to the conversion, only flash.bin was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single bootable
binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone (for
example, for secure boot purposes).
Also update imx8mq_evk.rst to remove the u-boot.itb copy step.
This is a cherry-pick of 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") adjusted to apply to i.MX8MQ.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Rename from vexpress_aemv8a.h -> vepxress_aemv8.h as new FVPs may not be
v8-A. No change in behavior.
This is towards future work to enable support for the FVP_BaseR.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Create a new documentation section for Arm Ltd boards with a sub-page
for the VExpress64 boards (FVP-A and Juno).
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
At present this is disabled, but it should work so long as the kernel does
not need EFI services. Enable it and add a note about remaining work.
Signed-off-by: Simon Glass <sjg@chromium.org>
When starting the app, locate all block devices and make them available
to U-Boot. This allows listing partitions and accessing files in
filesystems.
EFI also has the concept of 'disks', meaning boot media. For now, this
is not obviously useful in U-Boot, but add code to at least locate these.
This can be expanded later as needed.
We cannot use printf() in the early stub or app since it is not compiled
in
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add some long overdue instructions for building and installing U-Boot on
Allwinner SoC based boards.
This describes the building process, including TF-A and crust, plus
installation to SD card, eMMC and SPI flash, both from Linux and U-Boot
itself. Also describe FEL booting.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
UEFI:
* allow for more than 16 KiB UEFI variable size when using StMM
Others:
* make watchdog sysreset compatible with separate poweroff driver
* avoid OpenSSL deprecation warnings
-----BEGIN PGP SIGNATURE-----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=VFOg
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-01-rc4-4' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-01-rc4-4
UEFI:
* allow for more than 16 KiB UEFI variable size when using StMM
Others:
* make watchdog sysreset compatible with separate poweroff driver
* avoid OpenSSL deprecation warnings
This converts the following to Kconfig:
CONFIG_SYS_FSL_CLK
We move the exiting option to common/Kconfig near the other options to
control the contents of board_init_f() and note that this is a legacy
option. We further restrict this to where the call is going to be
non-empty, for the SoCs that had only been using this for some
MMC-related clocks.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is a 'y/n' selection, so fix it.
While at it remove the duplicate usage of CFG_CORE_HEAP_SIZE
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Long gone is the time a custom TF-A was needed for Puma, upstream TF-A
works just fine now.
The flashing instructions are updated to match how newer rkdeveloptool
and rkbin work.
Finally, rkbin provides a way to flash SPI via USB OTG interface so
let's document that.
Cc: Quentin Schulz <foss+u-boot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
QEMU currently generates a devicetree for use with U-Boot. Explain how to
obtain it.
Also explain how to merge it to produce a devicetree with the U-Boot
features included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Without this option QEMU appears to hang. Add it to avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
doc/usage/index.rst in branch origin/next includes usage/environment twice.
Remove the duplicate entry.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The Calxeda servers are using U-Boot as the primary bootloader, which
was shipped as part of a firmware upgrade package.
Even though the machines are considered legacy at this point, the port
still works, so deserves some documentation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These names are better used for access to devices provided by an EFI
layer. Use EFI_LOADER instead here, since these are only available in
U-Boot's EFI_LOADER layer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Literally adhering to the docs gave this wrong output:
U-Boot> setenv fdtaddr 0x87f00000
U-Boot> fdtaddr $fdtaddr
Unknown command 'fdtaddr' - try 'help'
Fixes: d80162cfc5 ("doc: Document how to apply fdt overlays")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At present there are Kconfig options for tracing, but sandbox uses
plain #defines to set them. Correct this and make the tracing command
default to enabled so that this is not needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Typically the bloblist is positioned at a fixed address in memory until
relocation. This is convenient when it is set up in SPL or before
relocation.
But for EFI we want to set it up only when U-Boot proper is running. Add
a way to allocate it using malloc() and update the documentation to cover
this aspect of bloblist.
Note there are no tests of this feature at present, nor any direct testing
of bloblist_init().
This can be added, e.g. by making this option controllable at runtime.
Signed-off-by: Simon Glass <sjg@chromium.org>
Configure SPI flash devices into SPL. Add SPI boot option to spl.c.
Document how to format flash for booting.
Signed-off-by: Thomas Skibo <thomas-git@skibo.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
UART1 use for U-Boot and Linux console instead of UART0 and
UART0 is reserved for Hart Software Services(HSS).
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add support of mtd backend for nor1 when this device is present on the
board, on STM32MP157C-EV1 for example, as the support of several MTD
spi-nor instance are now supported with commit b7f060565e ("mtd:
spi-nor: allow registering multiple MTDs when DM is enabled").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The support of a predefined DDR PHY tuning result is removed for
STM32MP1 driver because it is not needed at the supported frequency
when built-in calibration is executed.
The calibration parameters were provided in the device tree by the
optional node "st,phy-cal", activated in ddr helper file by the
compilation flag DDR_PHY_CAL_SKIP and filled with values generated
by the CubeMX DDR utilities.
This patch
- updates the binding file to remove "st,phy-cal" support
- updates the device trees and remove the associated defines
- simplifies the STM32MP1 DDR driver and remove the support of
the optional parameter "st,phy-cal"
After this patch, the built-in calibration is always executed
and the calibration registers are moved in the phy dynamic part;
that allows manual tests.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
* add description how to add RNG device
* for a disk specify format=raw to avoid a warning
* fix a typo
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Provide a way for sandbox MMC to present data from a backing file. This
allows a filesystem to be created on the host and easily served via an
emulated mmc device.
Signed-off-by: Simon Glass <sjg@chromium.org>
This command is fairly complicated so documentation is useful.
Unfortunately I an not sure how the MTD side of things works and cannot
find information about that.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Introduce compatible "linaro,scmi-optee" for SCMI transport channel
based on an OP-TEE service invocation.
Define "linaro,optee-channel-id" property to identify the OP-TEE SCMI
channel used by the protocol(s). OP-TEE SCMI transport can either use
shared memory or a static shared memory buffer identified by the DT.
These bindings were posted to the Linux kernel DT bindings mailing list
and acked by maintainer [1].
Link: [1] https://lore.kernel.org/linux-arm-kernel/20211029102118.GG6526@e120937-lin/T/
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Correct Sphinx style comments in include/lmb.h
Add the logical memory block API to the HTML documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This driver supports both pin muxing and GPIO support for the
pin control logic found on Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
This has different semantics in different places. Go with the bootm method
and put it in a common function so that the behaviour is consistent in
U-Boot. Update the docs.
To be clear, this changes the way that 'bootelf' and standalone boot
work. Before, if autostart was set to "fred" or "YES", for example, they
would consider that a "yes". This may change behaviour for some boards,
but the only in-tree boards which mention autostart use "no" to disable
it, which will still work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Wolfgang Denk <wd@denx.de>
Make various other updates suggested during review of the rST conversion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Make various updates suggested during review of the rST conversion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Suggested-by: Wolfgang Denk <wd@denx.de>
Add mention of this option since it does a similar thing to the text
environment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
At present U-Boot environment variables, and thus scripts, are defined
by CONFIG_EXTRA_ENV_SETTINGS. It is painful to add large amounts of text
to this file and dealing with quoting and newlines is harder than it
should be. It would be better if we could just type the script into a
text file and have it included by U-Boot.
Add a feature that brings in a .env file associated with the board
config, if present. To use it, create a file in a board/<vendor>
directory, typically called <board>.env and controlled by the
CONFIG_ENV_SOURCE_FILE option.
The environment variables should be of the form "var=value". Values can
extend to multiple lines. See the README under 'Environment Variables:'
for more information and an example.
In many cases environment variables need access to the U-Boot CONFIG
variables to select different options. Enable this so that the environment
scripts can be as useful as the ones currently in the board config files.
This uses the C preprocessor, means that comments can be included in the
environment using /* ... */
Also support += to allow variables to be appended to. This is needed when
using the preprocessor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Marek Behún <marek.behun@nic.cz>
Move this from the README to rST format.
Drop i2cfast since it is obviously obsolete and breaks the formatting.
Other changes and improvements are in a following patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Behún <marek.behun@nic.cz>
The last board that used to set CONFIG_LYNXKDI has been removed in
commit 242836a893 ("powerpc: ppc4xx: remove pcs440ep support"),
doc/README.lynxkdi only talks about a MPC8260 board being supported,
and the mpc8260 support has been removed four years ago in commit
2eb48ff7a2 ("powerpc, 8260: remove support for mpc8260") already,
and common/lynxkdi.c only consists of an "#error" statement these
days, so it seems like the LYNX KDI code is dead code nowadays.
Let's remove it now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Move this over to the new rST format.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Quite a lot of the code in common/relates to booting and images. Before
adding more it seems like a good time to move the code into its own
directory.
Most files with 'boot' or 'image' in them are moved, except:
- autoboot.c which relates to U-Boot automatically running a script
- bootstage.c which relates to U-Boot timing
Drop the removal of boot* files from the output directory, since this
interfers with the symlinks created by tools and there does not appear
to be any such file from my brief testing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
A previous patch added support for an mmio based TPM.
Add an example in QEMU on it's usage
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Document the update image and how to use the EFI UpdateCapsule.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In order to add other Kontron boards to the docs alongside the existing sl28 board,
we need to reduce the levels of the sections and change the title.
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The current EFI video driver only works when running in the stub. In that
case the stub calls boot services (before jumping to U-Boot proper) and
copies the graphics info over to the efi table. This is necessary because
the stub exits boot services before jumping to U-Boot.
The app maintains access to boot services throughout its life, so does not
need to do this. Update the driver to support calling boot services
directly.
Enable video output for the app. Note that this uses the
EFI_GRAPHICS_OUTPUT_PROTOCOL protocol, even though it mentions vesa.
A sample qemu command-line for this case is:
qemu-system-x86_64 -bios /usr/share/edk2.git/ovmf-ia32/OVMF-pure-efi.fd
-drive id=disk,file=try.img,if=none,format=raw -nic none
-device ahci,id=ahci -device ide-hd,drive=disk,bus=ahci.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Most modern platforms use 64-bit EFI so it is useful to have a U-Boot app
that runs under that. Add a (non-functional) build for this.
Note that --whole-archive causes the gcc 9.2 linker to crash, so disable
this for now. Once this is resolved, things should work.
For now, avoid mentioning the documentation for the 64-bit app, since it
does not work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
It is quite complicated to run U-Boot on QEMU since we have four
different builds and they must use different versions of qemu and the
UEFI binaries.
Add a script to help. It requires U-Boot itself to be built. Once that
is done you can use this script to build an image for use with qemu and
optionally run it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide human readable descriptions of the speed nodes instead of the name
of constants from the code.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The related boards have been removed four years ago already, in
commit 98f705c9ce ("powerpc: remove 4xx support"), so this README
file is not required anymore.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The PPC440 support has been removed in commit 98f705c9ce
("powerpc: remove 4xx support"). This patch removes this obsolete
file as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Thomas Huth <thuth@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The existing intructions in the U-Boot on EFI doc do not work with
the latest QEMU. Update the doc with the correct instructions, as
well as using the new OVMF URL link.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Samsung Galaxy A3, A5, A7 (2017) - middle class Samsung smartphones.
U-boot can be used as chain-loaded bootloader to gain control
on booting vanilla linux(and possibly others) kernels
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Samsung S9 SM-G9600 - Snapdragon SDM845 version of the phone,
for China \ Hong Kong markets.
Has unlockable bootloader, unlike SM-G960U (American market version),
which allows running u-boot as a chain-loaded bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Generic Interface (GENI) Serial Engine (SE) based uart
can be found on newer qualcomm SOCs, starting from SDM845.
Tested on Samsung SM-G9600(starqltechn)
by chain-loading u-boot with stock bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Provide preliminary instructions on how to get U-Boot to run on
Apple Silicon Macs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This uclass is intended to manage IOMMUs on systems where the
IOMMUs are not in bypass mode by default. In that case U-Boot
cannot ignore the IOMMUs if it wants to use devices that need
to do DMA and sit behind such an IOMMU.
This initial IOMMU uclass implementation does not implement and
device ops and is intended for IOMMUs that have a bypass mode
that does not require address translation. Support for IOMMUs
that do require address translation is planned and device ops
will be defined when support for such IOMMUs will be added.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
OF_HOSTFILE is used on sandbox configs only. Although it's pretty
unique and not causing any confusions, we are better of having simpler
config options for the DTB.
So let's replace that with the existing OF_BOARD. U-Boot would then
have only three config options for the DTB origin.
- OF_SEPARATE, build separately from U-Boot
- OF_BOARD, board specific way of providing the DTB
- OF_EMBED embedded in the u-boot binary(should not be used in production
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit a7e4f905d2.
The description originally written by Sughosh is still valid
even after the commit 47a25e81d3 ("Revert "efi_capsule: Move signature
from DTB to .rodata"") was applied.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Support for the PPC74xx processors has been removed in commit
d928664f41 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support")
more than 6 years ago already. So the corresponding README file
can now be removed, too.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Support for PPC4XX processors has been removed. So we should not mention it
in the documentation.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The PPC 440 support has been removed in commit 98f705c9ce
("powerpc: remove 4xx support") already, so this file is
certainly not required anymore.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Complete the Sphinx documentation in include/sysreset.h
Add the include to the generated HTML documentation of the U-Boot API.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
For enums documented according to the requirements in chapter
"Structure, union, and enumeration documentation" of
https://www.kernel.org/doc/html/latest/doc-guide/kernel-doc.html
errors occur with Sphinx 2.4.4 which disappear with Sphinx 3.4.3,
e.g.
/builds/u-boot/custodians/u-boot-efi/doc/api/sysreset:6:
./include/sysreset.h:60:Unknown interpreted text role "enum".
Sphinx 3.4.3 is the version used by Debian in the current release.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
On iMX8MM with Fast Boot fuse blown, the SIT and A-copy image are
placed at different offset than on iMX8MM with Fast Boot fuse NOT
blown. List both options and both offsets to avoid confusion.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The PERSIST_SECONDARY_BOOT is in GPR10 address 0x30390098, adjust the
text which currently says it is in GPR0 while using the correct address
of GPR10.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
After the conversion to binman in commit 8996e6b7c6 ("imx8mm_evk: switch
to use binman to pack images"), it is necessary to flash both flash.bin and
u-boot.itb to get a bootable system. Prior to this commit, only flash.bin
was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single
bootable binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone
(for example, for secure boot purposes).
Also update imx8mm_evk.rst to remove the u-boot.itb copy step.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
At present U-Boot always builds dtc if CONFIG_OF_CONTROL is defined, even
when DTC is provided. The built dtc is not actually used, so this is a
waste of time.
Update the Makefile logic to build dtc only if one is not provided to the
build with the DTC variable. Add documentation to explain this.
This saves about 3.5 seconds of elapsed time on a clean build of
sandbox_spl for me.
Signed-off-by: Simon Glass <sjg@chromium.org>
Brand names are supposed to be written with a capital,
so change them all.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the list of mainline U-boot supported Rockchip boards
rk3188 is placed below under the name rv3188. Give back it's
original name and sort the list in alphabetical order.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When a test hands on a real board there is no way on the console to obtain
any information about why it hung.
With sandbox we can actually find out that it died and get a signal or
exit code. Add this to make it easier to figure out what happened.
So instead of:
test/py/u_boot_spawn.py:171: in expect
c = os.read(self.fd, 1024).decode(errors='replace')
E OSError: [Errno 5] Input/output error
We get:
test/py/u_boot_spawn.py:171: in expect
c = os.read(self.fd, 1024).decode(errors='replace')
E ValueError: U-Boot exited with signal 11 (Signals.SIGSEGV)
Signed-off-by: Simon Glass <sjg@chromium.org>
This produces a lot of code output which is not very helpful and is quite
annoying to wade through. Use the short format by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Kontron SoM-Line i.MX8MM (N801x) by Kontron Electronics GmbH is a SoM
module with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC.
The matching evaluation boards (Board-Line) have 2 Ethernets, USB 2.0, HDMI/LVDS,
SD card, CAN, RS485 and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.
Currently there are the following SoM flavors (SoM-Line):
* N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
* N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
* N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND
And the according evaluation boards (Board-Line):
* N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
* N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
* N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...
Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
binman conversion made flashing flash.bin
and u-boot.itb necessary. Update binman config
to create a single flash.bin image again.
This updates imx8mp_evk and phyCORE-i.MX8MP as they share the
same binman config.
Updated also imx8mp_evk documentation.
Tested on phyCORE-i.MX8MP.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add documentation bits for the Radxa Zero
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: updated u200 MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Beelink GS-King X is a variant of the GS King boards but with an internal
USB to SATA bridge and advanced audio features.
[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.
Signed-off-by: Tom Rini <trini@konsulko.com>
OEM_REVISION is 32-bit unsigned number. It should be increased only when
changing software version. Therefore it should not depend on build time.
Change calculation to use U-Boot version numbers and set this revision
to date number.
Prior this change OEM_REVISION was calculated from build date and stored in
the same format.
After this change macro U_BOOT_BUILD_DATE is not used in other files so
remove it from global autogenerated files and also from Makefile.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for the IOT2050 Basic and Advanced devices. The Basic
used the dual-core AM6528 GP processor, the Advanced one the AM6548 HS
quad-core version.
Both variants are booted via a Siemens-provided FSBL that runs on the R5
cores. Consequently, U-Boot support is targeting the A53 cores. U-Boot
SPL, ATF and TEE have to reside in SPI flash.
Full integration into a bootable image can be found on
https://github.com/siemens/meta-iot2050
Based on original board support by Le Jin, Gao Nian and Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The devicetree binding files are in their own directory and use a simple
text format. Add a link for the binding for the /config node, since it
is otherwise hard to find.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- At this point there are a large number of Beaglebone boards, refer to
them as a family rather than a growing list.
- Reword customization as we're largely Kconfig-oriented now.
- Remove the NOR section as the relevant defconfigs have long been
removed and the general support was not updated.
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmFR2fMRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaAnAf/ZKPy3CRphbgAmbLhNQhQGpLosLcFp343
cv53gfsv1DakLRrhqMSnOQSVoTg9P22uHbooDDR9WHfZyEL6tvGZ+dgN2/wlDhDj
wbvvsM7FB+uvLVfMF3MURQBvy4dPO+FyCm/uHmry2V2uqWPw4ss+aVhxeQ5s4/oI
LpS6yaiM8UAj2GTUZSqJ1+/W7YG9N6tL73n0PDyCvSrdCkyPWqpww1rtST88SfFI
bBEWc6ksna/29haOwHQ2xopEbVxtHv2byULfqUtnsbtE4Ozw8o0fx66tdwPHTQlM
7eSuRiEbqjlJuUZFIbMat7nb7inZkaWupZ/Sr1HUUiDdKMygrRsQhg==
=x8Uf
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-next-27sep21' of https://source.denx.de/u-boot/custodians/u-boot-dm into next
Various of-platdata improvements, including CONFIG_OF_REAL
Convert some of these occurences to C code, where it is easy to do. This
should help encourage this approach to be used in new code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we have a 'positive' Kconfig option, use this instead of the
negative one, which is harder to understand.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current API is outdated as it requires a devicetree pointer.
Move these functions to use the ofnode API and update this globally. Add
some tests while we are here.
Correct the call in exynos_dsim_config_parse_dt() which is obviously
wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
The devicetree binding files are in their own directory and use a simple
text format. Add a link for the binding for the /config node, since it
is otherwise hard to find.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Use the more generic reset-gpios property name.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Version string is available in global variable char version_string[].
Macro U_BOOT_VERSION_STRING is not used by any other file, so remove it
completely from version.h. Other files were already converted to use
variable version_string[].
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Support using mmc command for enumerating mmc card in a given mode
Fix device_remove in mmc
Fix switch issue with send_status disabled
Drop 1ms delay in fsl_esdhc command sending
Revert "mmc: sdhci: set to INT_DATA_END when there are data"
The current list is missing a few items. Add them.
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Sort these and add a type so it is clear how to set the value. Add a note
about usage to the top. Correct the 'no-keyboard' binding which is missing
a prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Move this documentation to the new format.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add documentation on the usage of "mmc dev" and "mmc rescan" commands to
set user defined speed modes.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Move TI maintainership to Tom.
Updated with the following commands:
find ./ -name MAINTAINERS | xargs sed -i s/"Lokesh Vutla <lokeshvutla@ti.com>"/"Tom Rini <trini@konsulko.com>"/g
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Acked-by: Tom Rini <trini@konsulko.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
Per a request from Andre Przywara and agreed with by Peter Hoyes, the
vexpress aemv8r support wasn't quite ready to be merged, but the
discussion had moved off list. We should keep the first patch in the
series for now, but revert the rest. This reverts the following
commits:
e0bd6f31ce doc: Add documentation for the Arm vexpress board configs
30e5a449e8 arm: Use armv8_switch_to_el1 env to switch to EL1
b53bbca63b vexpress64: Add BASER_FVP vexpress board variant
2f5b7b7490 armv8: Add ARMv8 MPU configuration logic
37a757e227 armv8: Ensure EL1&0 VMSA is enabled
Signed-off-by: Tom Rini <trini@konsulko.com>
This Kconfig symbol was never added to U-Boot but it was mentioned in the
origin commit c35df7c9e4 ("qemu: arm64: Add documentation for capsule
update"). That's why remove it from documentation to be accurate.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Create a new documentation section for Arm Ltd boards with a sub-page
for the vexpress board (FVP-A, FVP-R and Juno).
Document how the armv8_switch_to_el1 environment variable can be used
to switch between booting from S-EL2/S-EL1 at runtime on the BASER_FVP.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
The BASER_FVP board variant is implemented on top of the BASE_FVP board
config (which, in turn, is based on the Juno Versatile Express board
config). They all share a similar memory map - for BASER_FVP the map is
inverted from the BASE_FVP
(https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map)
* Create new TARGET_VEXPRESS64_BASER_FVP target, which uses the same
board config as BASE_FVP and JUNO
* Adapt vexpress_aemv8a.h header file to support BASER_FVP (and rename
to vexpress_aemv8.h)
* Enable config to switch to EL1 for the BASER_FVP
* Create vexpress_aemv8r defconfig
* Provide an MPU memory map for the BASER_FVP
For now, only single core boot is supported.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[trini: Add MAINTAINERS, move BOOTCOMMAND to defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Over the time, the "stemmy" U-Boot board was tested on several other
Samsung smartphones based on ST-Ericsson NovaThor Ux500. Convert the
documentation to reStructuredText at doc/board/ste/stemmy.rst and
make the device list complete. Also note that the board now boots
into USB Fastboot instead of just ending up at the U-Boot prompt.
The device table is mostly taken from the postmarketOS wiki article
(https://wiki.postmarketos.org/wiki/ST-Ericsson_NovaThor_U8500).
All the newly added devices were tested by Linus Walleij.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
This resyncs us with the version found in v5.13 of the Linux kernel with
the following exceptions:
- Keep our u-boot specific tests / code area.
- Change the location of checkpatch.rst (which we now import)
- Drop the "use strscpy" test as we don't have that, but do have strlcpy
and want that used now.
- Keep debug/printf in the list for $logFunctions
And note that we now also include the spdxcheck.py tool that
checkpatch.pl supports calling out to, and include upstream's
checkpatch.rst in our develop section of the documentation.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
All platforms define CONFIG_SYS_LOAD_ADDR, but only some define
CONFIG_LOADADDR. Very very rarely are these not the same address, and
qemu-ppce500 is one such case. However, based on reading the history of
the code, this mismatched value was simply a copy-paste from other
PowerPC platforms where it is this unused currently. Switch the code to
use CONFIG_SYS_LOAD_ADDR and update the documentation.
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
A rather common kind of external watchdog circuit is one that is kept
alive by toggling a gpio. Add a driver for handling such a watchdog.
The corresponding linux driver apparently has support for some
watchdog circuits which can be disabled by tri-stating the gpio, but I
have never actually encountered such a chip in the wild; the whole
point of adding an external watchdog is usually that it is not in any
way under software control. For forward-compatibility, and to make DT
describe the hardware, the current driver only supports devices that
have the always-running property. I went a little back and forth on
whether I should fail ->probe or only ->start, and ended up deciding
->start was the right place.
The compatible string is probably a little odd as it has nothing to do
with linux per se - however, I chose that to make .dts snippets
reusable between device trees used with U-Boot and linux, and this is
the (only) compatible string that linux' corresponding driver and DT
binding accepts. I have asked whether one should/could add "wdt-gpio"
to that binding, but the answer was no:
https://lore.kernel.org/lkml/CAL_JsqKEGaFpiFV_oAtE+S_bnHkg4qry+bhx2EDs=NSbVf_giA@mail.gmail.com/
If someone feels strongly about this, I can certainly remove the
"linux," part from the string - it probably wouldn't the only place where
one can't reuse a DT snippet as-is between linux and U-Boot.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Documentation:
* Rename Freescale to NXP
* Document structures used for the UEFI TCG2 protocol
UEFI:
* Device paths must use EfiBootServicesData
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEK7wKXt3/btL6/yA+hO4vgnE3U0sFAmEf+AgACgkQhO4vgnE3
U0skxhAAjjv6yMYLYlj2YNTtYDS2zVsnsY8i/vmWNmGYvwfrlcUC/e3J00ftBIjI
DEwImrzefvQwr4NOZgIlyxR81NwboWULxvHSF5avwctxQVoTElkSfE2Ji+nFYa23
P/L7E/Zf+NwTHBlE1wfkNJPZ/zya73DTOe+MGWvLnvOX56JZqEJOgmTtcQntRUll
9zkB76j6sCk8B3ydFZmzGqhB4aslJBypG+bQB72XXGVBZoHb9pEPv90hBl616AN/
5H8WewxTE2s6z3IfexxPAc7ssMQuW3RWw0WsJvBVviw8tSPj4SZjg5HNHAM3mz/i
EXHUqAEySP1oT6P4hVef7Xc9gC67N+dVZGAA1QcZBkAnH+BQQ2GmIWX5+3mZJflq
3eHWhMUHWc4q76MbN9QqReAo3wJ3GsBqdA1oORR5FgIPwEVl0jwQMYv6frC/vB6/
6VX8WcbAWsixjf8QeQlibfMqBO9xZI1Iue5rN6DcwMey6dZrDnXGMdk7Woj6F4ga
tERYBt+UBawTf2ww24wMXc7Hw2dZ6kj44ls2doRFKqHOpaY9Mk2QPTaVPrFkj33J
3xlH2BYdB3ALriS1jN6Qcq6xEwyaMdkj5MzVyitunaCLiAKKORwGf0chkqiRiA+k
zEET0uDBtO7beraiUJU9jeMPcVj3mYpiFR/CZBD/HWOVB/KwhGU=
=gMKg
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-10-rc3' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-10-rc3
Documentation:
* Rename Freescale to NXP
* Document structures used for the UEFI TCG2 protocol
UEFI:
* Device paths must use EfiBootServicesData
The driver will use a syscon regmap as backend and supports both
16 and 32 size value. The value will be stored in the CPU's endianness.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
'make htmldocs' does not use file doc/board/st/st.rst because the name
matches the directory name. Let's rename it to st-dt.rst.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Having "i.MX7D/i.MX8MM SRC_GPR10 PERSIST_SECONDARY_BOOT for bootloader A/B
switching" at the top level of the documentation tree does not make sense.
Move it to board specific information.
Fixes: 59e3d1bd49 ("doc: imx: psb: Document usage of SRC_GPR10 PERSIST_SECONDARY_BOOT for A/B switching")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
TF-A for STM32MP15 now supports the FIP: it is a packaging format which
includes the secure monitor, u-boot-nodtb.bin and u-boot.dtb
This FIP file is loaded by FSBL = TF-A BL2.
This patch updates the board documentation to use this FIP file and no
more u-boot.stm32 (with STM32 image header) which is no more generated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
With device tree binding migration to yaml it is difficult to synchronize
the binding from Linux kernel to U-Boot.
Instead of maintaining the same dt bindings, this patch adds in the U-Boot
documentation the path to the device tree bindings in Linux kernel for
STMicroelectronics devices, when they are used without modification.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add links for referenced text files.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
