Commit graph

285 commits

Author SHA1 Message Date
vishnupatekar
f542948b1e sunxi: clk: add basic clocks for A83T
Add basic clocks pll1, pll5, and some default values from allwinner u-boot.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
[hdegoede@redhat.com] Fix PLL6 init to run at 600 MHz instead of 288 MHz,
fixing the mmc support not working
[hdegoede@redhat.com] Fix PLL init code to properly wait for the PLL-s to
stabilize, fixing cold-booting directly from sdcard not working
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-12-10 15:45:47 +01:00
vishnupatekar
d5a3357f1b sunxi: Add support for UART0 in PB pin group on A83T
On A83T, PB9,PB10 are UART0 pins.
On allwinner A83T Dev board(h8homlet), this uart0 serial connector
is exposed.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-12-10 11:14:21 +01:00
Hans de Goede
cbc1a91afb sunxi: Set AHB1 clock to PLL6/3 on all clock_sun6i.h using SoCs
According to the datasheets the max speed of AHB1 is 276 MHz, so
setting it to PLL6 / 3 which gives us 200MHz everywhere is fine,
and gives us a nice speed-up in certain workloads.

Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Tested-by: Chen-Yu Tsai <wens@csie.org>
2015-12-10 11:14:16 +01:00
Siarhei Siamashka
52d093112a sunxi: clock: Set AHB1 clock frequency to 200MHz on Allwinner H3
The 3.4 kernel from the Allwinner SDK is clocking AHB1 at 200MHz
on Allwinner H3 and using PLL6 as the clock source (PLL6/3).
This can be verified by reading the value of the AHB1_APB1_CFG_REG
register via /dev/mem. It always reads as 0x3180 regardless of
the current cpufreq operating point. So this configuration should
be safe for use in U-Boot too.

PLL6 also needs to be configured before it is used as the clock
source, according to the "CCU / Programming Guidelines" section
of the Allwinner manual.

The current low AHB1 clock speed is limiting the USB transfer
speed when booting via FEL. This patch can increase the FEL USB
transfer speed from ~510 KB/s to ~950 KB/s.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22 11:31:00 +01:00
Jens Kuske
0404d53f2f sunxi: Add H3 DRAM initialization support
Based on existing A23/A33 code and the original H3 boot0.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22 11:31:00 +01:00
Jens Kuske
1c27b7dcd0 sunxi: Add basic H3 support
Add initial sun8i H3 support, only uart + mmc are supported for now.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22 11:30:59 +01:00
Bernhard Nortmann
af654d1461 sunxi: retrieve FEL-provided values to environment variables
This patch extends the misc_init_r() function on sunxi boards
to test for the presence of a suitable "sunxi" SPL header. If
found, and the loader ("fel" utility) provided a non-zero value
for the boot.scr address, then the corresponding environment
variable fel_scriptaddr gets set.

misc_init_r() also sets (or clears) the "fel_booted" variable depending
on the active boot device, using the same logic as spl_boot_device().

The goal is to provide sufficient information (within the U-Boot
environment) to make intelligent decisions on how to continue the boot
process, allowing specific customizations for the "FEL boot" case.

Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-09-29 11:50:07 +02:00
Bernhard Nortmann
a188438175 sunxi: (mksunxiboot) signature to indicate "sunxi" SPL variant
This patch follows up on a discussion of ways to improve support
for the sunxi FEL ("USB boot") mechanism, especially with regard
to boot scripts, see:
https://groups.google.com/d/msg/linux-sunxi/wBEGUoLNRro/rHGq6nSYCQAJ

The idea is to convert the (currently unused) "pad" bytes in the
SPL header into an area where data can be passed to U-Boot. To
do this safely, we have to make sure that we're actually using
our "sunxi" flavor of the SPL, and not the Allwinner boot0.

The modified mksunxiboot introduces a special signature to the
SPL header in place of the "pub_head_size" field. This can be
used to reliably distinguish between compatible versions of sunxi
SPL and anything else (older variants or Allwinner's boot0).

Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-09-29 11:50:07 +02:00
Bernhard Nortmann
e954eb8028 sunxi: move SPL-related definitions to platform-specific include
The sunxi platform currently doesn't seem to make any use of the
asm/arch-sunxi/spl.h file. This patch moves some declarations from
tools/mksunxiboot.c into it.

This enables us to reuse those definitions when extending the
sunxi board code (boards/sunxi/boards.c).

Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-09-29 11:50:07 +02:00
Chen-Yu Tsai
92369844ec sunxi: Enable non-secure access to RTC on sun6i (A31s)
On the A31s the RTC is by default secured. Thus when u-boot
loads the kernel in non-secure world, the RTC is unavailable. The
SoC has a TrustZone Protection Controller, which can be used to
enable non-secure access to the RTC.

On the A31 the TZPC doesn't seem to do anything, i.e. changes to
its register contents do not affect access to the RTC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-08-31 08:43:42 +02:00
Hans de Goede
55ea98d8b1 sun6i: clock: Add support for the mipi pll
Add support for the mipi pll, this is necessary for getting higher dotclocks
with lcd panels.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-14 08:37:39 +02:00
Hans de Goede
49043cbad1 sunxi: clock: Add clock_get_pll3() helper function
Add a helper function to get the pll3 clock rate.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-14 08:37:38 +02:00
Hans de Goede
d8d079966f sunxi: display: Fix composite video out on sun5i
The tv-encoder on sun5i is slightly different compared to the one on
sun4i/sun7i.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-14 08:37:36 +02:00
Hans de Goede
0ecb43a8d0 sunxi: display: Add a few extra register and constant defines
Add a few extra sunxi display registers and constant defines.

Also rename some existing defines (e.g. dropping _GCTRL) and make
some more generic (e.g. dropping the 2x scaling from
SUNXI_LCDC_TCON1_TIMING_V_TOTAL).

This is a preparation patch for adding composite video out support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-08 16:26:20 +02:00
Hans de Goede
c9f8947e66 sunxi: usb-phy: Never power off the usb ports
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.

Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.

This patch removes the powering off calls, fixing the undesirable power
bouncing.

Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-08 16:26:19 +02:00
Karol Gugala
ad00829971 sunxi: nand: Add pinmux and clock settings for NAND support
To enable NAND flash in sunxi SPL,
pins 0-6, 8-22 and 24 on port C are configured.

Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-08-08 16:26:19 +02:00
Paul Kocialkowski
95de1e2f26 usb: musb-new: CONFIG_MUSB prefix replacement with CONFIG_USB_MUSB
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-08-05 17:20:34 +02:00
Hans de Goede
d42faf3198 sunxi: musb: Move musb config and platdata to the sunxi-musb glue
Move the musb config and platdata to the sunxi-musb glue, which is where
it really belongs. This is preparation patch for adding device-model
support for the sunxi-musb-host code.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-07-25 11:22:55 +02:00
Hans de Goede
48c06c98ec sunxi: usb-phy: Add support for reading otg id pin value
Add support for reading the id pin value of the otg connector to the usb
phy code.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-07-25 11:22:54 +02:00
Daniel Kochmański
645c48f50e sunxi: Create helper function veryfing valid boot signature on MMC
This patch extracts checking for valid SD card "eGON.BT0" signature from
`board_mmc_init` into function `sunxi_mmc_has_egon_boot_signature`.

Buffer for mmc sector is allocated and freed at runtime. `panic` is
triggered on malloc failure.

Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Small bugfix to make it work for devs other then mmc0]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-07-24 16:17:08 +02:00
Chen-Yu Tsai
e506889c96 sunxi: Add support for UART0 in PB pin group on A33
The A33 adds a pinmux function for UART0 in the PB pin group.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-07-05 11:32:11 +02:00
Ian Campbell
da9971d1b3 Revert "sunxi/nand: Add support to the SPL for loading u-boot from internal NAND memory"
This reverts commit f76eba38b3.

This patch did not have a full and proper copyright/S-o-b chain.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>

Conflicts:
	include/configs/sun6i.h
	include/configs/sun8i.h
2015-06-28 11:46:31 -04:00
Daniel Kochmański
f76eba38b3 sunxi/nand: Add support to the SPL for loading u-boot from internal NAND memory
This commit adds support to the sunxi SPL to load u-boot from the internal
NAND. Note this only adds support to access the boot partitions to load
u-boot, full NAND support to load the kernel, etc. from the nand data
partition will come later.

Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-29 13:46:36 +02:00
Roy Spliet
d0f4200392 sunxi: Match sun4i, sun6i, sun9i CCI definitions for NAND and DMA
Make sure definitions for NAND clock and DMA gate bits are the same
across boards.

Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-29 13:46:36 +02:00
Roy Spliet
a19e735d3c sunxi: Add DMA definitions
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-29 13:46:36 +02:00
Hans de Goede
1871a8ca62 sun9i: Basic sun9i (A80) support
Add initial sun9i (A80) support, only uart + mmc are supported for now.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-29 13:46:36 +02:00
Hans de Goede
83edb2ace6 sunxi: video: Fix lvds panel support for sun6i+
We've never tested the lvds panel support on sun6i+ SoCs until now, and
unsurprisingly the lvds code needed some fixes to work on my ga10h A33
tablet with lvds panel. This makes the panel on that tablet actually work.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-19 18:46:44 +02:00
Hans de Goede
8975cdf4bc sunxi: Make DRAM_ODT_EN Kconfig setting a bool
Make DRAM_ODT_EN Kconfig setting a bool, add a separate DRAM_ODT_CORRECTION
setting for A23 SoCs and use DRAM_ODT_EN Kconfig everywhere instead of
only in dram_sun4i.c and hardcoding odt_en elsewhere.

Note this commit makes no functional changes for existing boards,
its purpose is to allow changing the odt_en value on future A33 boards.

For sun4i/sun5i/sun7i boards which set DRAM_ODT_EN=y (which no defconfigs
currently do) this patch turns on odt for both the DQ and the DQS lines,
whereas previously it was possibly (but not desirable) to turn odt on only
for one of them by setting the in DRAM_ODT_EN option to 1 or 2 instead of 3.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
2015-05-19 18:46:44 +02:00
Laurent Itti
5cd83b11f9 sunxi: add support for UART2 on A23/A33
Add support for UART2 (2-pin version but note that RTS/CTS pins are available
pn that port for possible future use), can be selected in config
by using CONFIG_CONS_INDEX=3

Signed-off-by: Laurent Itti <laurentitti@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-19 18:37:30 +02:00
Hans de Goede
6a72e804a2 sunxi: ohci: Add ohci usb host controller support
This commit adds support for the OHCI companion controller, which makes
usb-1 devices directly plugged into to usb root port work.

Note for now this switches usb-keyboard support for sunxi back from int-queue
support to the old interrupt polling method. Adding int-queue support to the
ohci code and switching back to int-queue support is in the works.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-14 18:49:32 -06:00
Hans de Goede
e13afeef6f sunxi: usb: Do not call phy_probe from hcd code
The 2/3 usb-phys on the sunxi SoCs are really a single separate functional
block, and are modelled as such in devicetree. So once we've moved all the
sunxi usb code to the driver-model then phy_probe will be called once
for the entire block from the driver-model enumeration code.

Move to this now as this also avoids problems with phy_probe being called
multiple times once we introduce ohci support. This also allows us to get rid
of the sunxi_usb_phy_enabled_count variable as phy_probe now is guaranteed
to be called only once.

Since we're effectively rewriting the probe / remove functions, move them
to the end of the file while we are at it, as that is the most logical place
for them.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:55 +02:00
Hans de Goede
2aacc4239c sunxi: usb: Rename the usbc.? files to usb_phy.?
The usbc.? files now only contain usb-phy related code, rename them to make
this clear.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:55 +02:00
Hans de Goede
7b798658b2 sunxi: usb: Rename sunxi_usbc_foo functions to sunxi_usb_phy_bar
Rename the sunxi_usbc_foo functions to sunxi_usb_phy_bar to make it clear
that these are usb-phy functions. Also change the verbs & nouns in the suffix
to match the verbs & nouns used in the Linux kernels generic phy framework.

This patch purely renames things, it contains no functional changes.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:55 +02:00
Hans de Goede
a781c97aaa sunxi: usb: Remove sunxi_usbc_get_io_base function
This is the only function left in sunxi/usbc.c which is not phy related,
so remove it.

This is a preparation patch for turning the usbc.c code into a proper
usb phy driver.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:54 +02:00
Hans de Goede
421b32b880 sunxi: axp: Remove non driver-model support from the axp gpio code
Now that all sunxi boards are using driver-model for gpio (*), we can remove
the non driver-model support from the axp gpio code, and the glue to call
into the axp gpio code from the sunxi_gpio non driver-model code.

*) For the regular u-boot build, SPL still uses non driver-model gpio for
now, but the SPL never uses axp gpios support and we were already not building
axp-gpio support for the SPL.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:54 +02:00
Hans de Goede
aab096401c sunxi: gmac: Move sunxi_gmac_initialize proto out of netdev.h
netdev.h should not be included in driver-model enabled builds (doing so
causes compiler warnings about struct eth_driver not being declared), but
we do use sunxi_gmac_initialize in the driver-model case, so move it out of
netdev.h .

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:53 +02:00
Hans de Goede
f9b7a04bc8 sunxi: axp: Add driver-model support to the axp_gpio code
Add driver-model support to the axp_gpio code, note that this needs a small
tweak to the driver-model version of sunxi_name_to_gpio to deal with the
vbus detect and enable pins which are not standard numbered gpios.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:53 +02:00
Hans de Goede
2fcf033d36 sunxi: axp: Move axp gpio code to a separate axpi-gpio driver
Move the axp-gpio code out of the drivers/power/axp*.c code, and into
a new separate axpi-gpio driver.

This change drops supports for the gpio3 pin on the axp209, as that requires
special handling, and no boards are using it.

Besides cleaning things up by moving the code to a separate driver, as
a bonus this change also adds support for the (non vusb) gpio pins on the
axp221 and the gpio pins on the axp152.

The new axp-gpio driver gets its own Kconfig option, and is only enabled
on boards which need it. Besides that it only gets enabled in the regular
u-boot build and not for the SPL as we never need it in the SPL.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:53 +02:00
Hans de Goede
1d624a4f08 sunxi: axp: Move axp pmic register helpers to a separate file
Move the register helpers used to access the registers via p2wi resp.
rsb bus on the otherwise identical axp221 and axp223 pmics to a separate
file, so that they can be used by the upcoming standalone axp gpio driver
too.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:53 +02:00
Vishnu Patekar
ffc0ae0c70 sunxi: Add a33 dram init code
Based on Allwinner dram init code from the a33 bsp:
https://github.com/allwinner-zh/bootloader/blob/master/basic_loader/bsp/bsp_for_a33/init_dram/mctl_hal.c

Initial u-boot port by Vishnu Patekar, major cleanup / rewrite by
Hans de Goede.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:51 +02:00
Hans de Goede
886a7b45ef sunxi: Add support for A33 PLL11 (second DRAM pll)
Add support for the new second DRAM PLL found on the A33 SoC.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:51 +02:00
Hans de Goede
5e6bacdb84 sunxi: s/sun8i/sun8i_a23/
This is a preparation patch for adding A33 support, which will have a
mach name of sun8i-a33.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:51 +02:00
Hans de Goede
44d8ae5b69 sunxi: Introduce a hidden SUNXI_GEN_SUNxI Kconfig bool
sun6i and newer (derived) SoCs such as the sun8i-a23, sun8i-a33 and sun9i
have a various things in common, like having separate ahb reset control
registers, the SID living inside the pmic, custom pmic busses, new style
watchdog, etc.

This commit introduces a new hidden SUNXI_GEN_SUN6I Kconfig bool which can be
used to check for these features avoiding the need for an ever growing list
of "#if defined CONFIG_MACH_SUN?I" conditionals as we add support for more
"new style" sunxi SoCs.

Note that this commit changes the behavior of the gmac and hdmi code for
sun8i and the upcoming sun9i devices. This does not matter as sun8i does
not have gmac nor hdmi, and sun9i has new hardware-blocks for these so
the old code will not work there.

Also this is intentional as if a sun8i / sun9i variant which does use the
old hwblocks shows up then the GEN_SUN6I code paths will be the right ones
to use.

For completeness this also adds a SUNXI_GEN_SUN4I bool for A10/A13/A20.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:51 +02:00
Paul Kocialkowski
6c739c5d8a sunxi: Complete i2c support for each supported platform
Sunxi platforms come with at least 3 TWI (I2C) controllers and some platforms
even have up to 5. This adds support for every controller on each supported
platform, which is especially useful when using expansion ports on single-board-
computers.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:33:17 +02:00
Paul Kocialkowski
dd82242b4d i2c: mvtwsi: Support for up to 4 different controllers
Orion5x, Kirkwood and Armada XP platforms come with a single TWSI (I2C) MVTWSI
controller. However, other platforms using MVTWSI may come with more: this is
the case on Allwinner (sunxi) platforms, where up to 4 controllers can be found
on the same chip.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:33:17 +02:00
Paul Kocialkowski
8deacca975 sunxi: Complete mmc pin mux for each supported platform, configured with Kconfig
Sunxi platforms have different possible mmc pin mux setups (except for mmc0),
which are different across platforms.

This lets users configure which is used through the CONFIG_MMC*_PINS Kconfig
options. This is especially relevant when a second (in addition to mmc0) port
is used and CONFIG_MMC_SUNXI_SLOT_EXTRA is enabled.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Paul Kocialkowski
487b3277d4 sunxi: GPIO pin mux hardware-feature-specific function index defines
Each hardware feature exposed through the GPIO pin mux is usually using the same
function index (for a given port), so there is no need to define one value per
pin: one value per hardware feature per port is sufficient, avoids duplication
and makes everything easier to understand.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Paul Kocialkowski
ebd468b2d2 sunxi: common VBUS detection logic in usbc
VBUS detection could be needed not only by the musb code (to prevent host mode),
but also by e.g. gadget drivers to start only when a cable is connected.

In addition, this allows more flexibility in vbus detection, as it could easily
be extended to other USBC indexes. Eventually, this would help making musb
support independent from a hardcoded USB controller index (0).

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Paul Kocialkowski
f7c7ab636a power: axp221: Virtual VBUS detect and enable GPIOs to replace separate logic
This converts the VBUS detection and enable logic to GPIO instead of separate
axp functions and checks that have to be used aside usual GPIO functions.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Paul Kocialkowski
991963bce9 sunxi: gpio: Indentation fix
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Hans de Goede
246e3b8787 sunxi: musb: Fix some lo speed devices not working with musb host
The usb0 / otg phy on sunxi boards has a bug where it wrongly detects a
high speed squelch on usb reset deassert when a lo speed device is plugged in.

The android kernel has a work around for this in the form of temporary
disabling the phy's squelch detection on reset deassert, this commit adds
the same workaround to the u-boot sunxi musb code, thereby fixing various usb
lo speed devices not working.

Tested with a (before non working) usb keyboard and a usb 2.4 GHz wireless
keyboard/mouse combo receiver.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-29 12:58:59 +02:00
Hans de Goede
f388a26d11 sunxi: Fix sun5i mbus speed when booting old kernels
Older linux-sunxi-3.4 kernels override our PLL6 setting with 300 MHz,
halving the mbus frequency, so set it to 300 MHz ourselves and base the
mbus divider on that.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-21 16:53:37 +01:00
Simon Glass
942cb0b6a2 sunxi: Normalise FEL support
Make sunxi's FEL code fit with the normal U-Boot boot sequence instead of
creating its own. There are some #ifdefs required in start.S. Future work
will hopefully remove these.

This series is available at u-boot-dm, branch sunxi-working.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-16 20:15:09 +01:00
Hans de Goede
51637afe98 sunxi: dram: Un-inline dram helper functions
Move the dram helper functions to a separate C file, rather then having them
as inline helpers in dram.h. This saves 144 bytes in the .text segment for
sun6i builds.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-02-16 20:05:52 +01:00
Hans de Goede
37d46dd3c4 sunxi: rsb: Move rsb_set_device_mode() call to rsb_init()
It turns out that the device_mode_data is rsb specific, rather then slave
specific, so integrate the rsb_set_device_mode() call into rsb_init().

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-02 13:55:14 +01:00
Hans de Goede
d35488c735 sunxi: rsb: Add sun9i (A80 support)
Add support for the A80 to the rsb code.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-02 13:55:14 +01:00
Hans de Goede
c13f60d92a sunxi: Add a GMAC Transmit Clock Delay Chain Kconfig option
And use this to set the GMAC Transmit Clock Delay Chain value on Banana
boards, rather then keying of CONFIG_TARGET_FOO.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-02 13:55:14 +01:00
Hans de Goede
1a800f7af3 sunxi: Hookup OTG USB controller support
Hookup OTG USB controller support and enable the otg controller + USB-keyb
on various tablets.

This allows tablet owners to interact with u-boot without needing to solder
a serial console onto their tablet PCB.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:56 +01:00
Hans de Goede
7cd6f92d41 sunxi: video: Use frontend for dma on sun4i to fix memory bandwidth problems
Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. On sun4i use the display frontend engine to do the dma from
memory, as the frontend does have deep enough fifo-s.

As added advantage of this is that it results in much better memory bandwidth
as it reduces the amount of dram bank switches, for more details see:

http://ssvb.github.io/2014/11/11/revisiting-fullhd-x11-desktop-performance-of-the-allwinner-a10.html

Note that this changes the pipeline searched for in the simplefb node, we can
get away with doing this now, since no kernel has yet shipped with simplefb
dtb nodes, and I will make sure to get a simplefb node with the new pipeline
into 3.19 before it ships.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:56 +01:00
Hans de Goede
8ffc487c75 sunxi: Stop differentiating between 512M and 1G variants of the same board
While working on adding more boards I noticed that we lack a config for
the 512M cubieboard, and that some of the new boards which I want to add also
have 512M and 1G variants, rather then adding 2 defconfig's for all of these,
lets switch the exising boards which have both a 512M and 1024M variant over
to the sun4i dram autoconfig code.

This also drops the foo_RAMSIZE_defconfig variants of boards where we currently
have 2 separate configs already.

Note:
1) The newly introduced CONFIG_DRAM_EMR1 kconfig value is not used with
a value other then its default for now, but we need this to be configurable
to support some new boards with auto dram config.

2) We always set all CONFIG_DRAM_foo values in defconfigs, even if they match
the defaults, this is done to make it more clear what values are used for a
certain board.

This has been tested on a Mele A1000, Mini-X and a Cubieboard, all 1G
variants, the dram autoconfig code has also been tested on a 512M mk802
(a defconfig for the mk802 is added in a later patch).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:56 +01:00
Hans de Goede
daf22636c2 sunxi: mmc: Add support for sun9i (A80)
The clocks on the A80 are hooked up slightly different, add support for this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:55 +01:00
Hans de Goede
e35377d726 sun9i: Add clock_sun9i.h with ccu register layout for sun9i
Add a headerfile with the sun9i ccu register layout.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:55 +01:00
Hans de Goede
ee74fec845 sun9i: Add cpu_sun9i.h with iomem defines
Add a headerfile with all the base addresses from the sun9i blocks.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:55 +01:00
Hans de Goede
9803e4e1db sunxi: Rename cpu.h to cpu_sun4i.h
sun4i - sun8i have (aprox.) the same iomem layout, but sun9i is quite
different, so add a wrapper cpu.h which includes the right mach specific
cpu_sun#i.h based on mach, like we already do with clock.h and dram.h .

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:55 +01:00
Hans de Goede
cc67a0b6e5 sunxi: Move clock_get_pllX / clock_set_pllX protos to mach specific headers
Which pll-s are available depends on the machine type, move the
clock_get_pllX / clock_set_pllX prototypes to the clock_sun?i.h header files
so that we only declare what is actually available. e.g. clock_get_pll5p()
is not available on sun6i / sun8i, and with sun9i we get a completely
different set of plls.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:55 +01:00
Hans de Goede
6515032e3b sunxi: display: Make lcd display clk phase configurable
While running some tests with an Olinuxino-A13-Micro + a 7" Olimex LCD module
I noticed that the screen flickered. This is caused by the lcd display clk
phase reg value being set to 0, where it should be 1 in this setup.

This commit adds a Kconfig option for the lcd display clk phase, so that we
can set it per board. This defaults to 1, because looking at all the fex
files in sunxi-boards, that is by far the most used value.

This commit updated the Ippo and MSI Primo73 tablet defconfigs to override the
default of 1 with 0, as that is the correct value for those tablets, this
keeps the register settings the same as before this commit.

The Olinuxino-A13 defconfigs are not updated, changing the register setting
for these boards from 0 to 1, this is intentional.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:55 +01:00
Hans de Goede
4458b7a6e1 sunxi: usbc: Add support for usb0 to the common usbc code
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:40 +01:00
Hans de Goede
0eccec4ef1 sunxi: Move usb-controller init code out of ehci-sunxi.c for reuse for otg
Most of the usb-controller init code found in ehci-sunxi.c also is necessary
to init the otg usb controller, so move it to a common place.

While at it also update various #ifdefs / defines for sun8i support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:40 +01:00
Hans de Goede
213480e12d sunxi: video: Add lvds support
Add support for lvds lcd panels

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14 14:56:40 +01:00
Hans de Goede
d9786d2380 sunxi: video: Add VGA output support
Add support for VGA directly from the sunxi SoC / display engine.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
2dae800f1e sunxi: video: Add lcd output support
Add lcd output support, see the new Kconfig entries and doc/README.video for
how to enable / configure this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
5489ebc7af sunxi: video: Modify sunxi_lcdc_pll_set to work with both tcon0 and tcon1
Modify sunxi_lcdc_pll_set to work with both tcon0 and tcon1, this is a
preparation patch for adding lcd support.

While at it also swap the divider search order, searching from low to
high, as the comment above the code says we should do. In cases where there
are multiple solutions this will result in picking a lower pll clock and
divider, which is more stable and saves power.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
6c727e09a0 sunxi: gpio: Add support for gpio pins on the AXP209 pmic
Some boards use GPIO-s on the pmic, one example of this is the A13-OLinuXino
board, which uses gpio0 of the axp209 for the lcd-power signal.

This commit adds support for gpio pins on the AXP209 pmic, the sunxi_gpio.c
changes are universal, adding gpio support for the other AXP pmics (when
necessary) should be a matter of adding the necessary axp_gpio_foo functions
to their resp. drivers, and add "#define AXP_GPIO" to their header file.

Note this commit only adds support for the non device-model version of the
gpio code, patches for adding support to the device-model version are very
welcome.

The string representation for these gpio-s is AXP0-#, the 0 in the AXP0 prefix
is there in case we need to support gpio-s on more then 1 pmic in the future.
At least A80 boards have 2 pmics, and we may end up needing to support gpio-s
on both.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:38 +01:00
Hans de Goede
d27f7d14ea sunxi: gpio: Properly sort mux defines by port number
Move a few mux defines around so that all the mux defines are properly sorted
by port number.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:38 +01:00
Hans de Goede
876aaafdbd sunxi: video: Set input sync enable
Add a write to the "unknown" (*) register to enable auto input sync, when
initially adding sunxi hdmi output support this magic write from the android
kernel code was missed, causing lcdc -> hdmi encoder sync problems.

With this write added, we can drop the modesetting retries and the extra
delays added to work around these sync problems.

With the retries dropped there also is no need to 0 all the enable flags at
the beginning of the modeset, as they are initialized to 0 already by
engines_init.

*) "unknown" is the actual name of this register in the android kernel sources

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14 14:56:38 +01:00
Hans de Goede
5ee0bea49a sunxi: video: Add hdmi support
So far we've been programming the hdmi-encoder to send out dvi data over the
hdmi connector. This works well for most devices, including hdmi devices, but
not all devices accept dvi data on a hdmi input.

Add support for sending proper hdmi data over the hdmi output found on most
sunxi boards. This can be turned on by adding monitor=hdmi as option to the
video-mode env. variable.

A follow up patch will determine whether to send dvi or hdmi automatically when
EDID is used.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14 14:56:38 +01:00
Hans de Goede
75481607c7 sunxi: video: Add DDC & EDID support
Add DDC & EDID support and use it to automatically select the native mode of
the attached monitor. This can be disabled by adding edid=0 as option
to the video-mode env. variable.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14 14:56:38 +01:00
Hans de Goede
25508ab26c sunxi: Fix PLL1 running at half speed on sun8i
PLL1 on sun6i / sun8i also has a p factor which divides the clock by
2^p (to the power p). On sun6i the p factor is ignored, but on sun8i it is
used and we were setting it to 1, resulting in the CPU running at 504 MHz
instead of 1008 MHz, this commit fixes this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Siarhei Siamashka
c3d2b963c6 sunxi: Fix buggy sun6i/sun8i DRAM size detection logic
After reboot, reset or even short power off, DRAM typically retains
the old stale data for some period of time (for this type of memory,
the bits of data are stored in slowly discharging capacitors).

The current sun6i/sun8i DRAM size detection logic, which is
inherited from the Allwinner code, relies on using a large magic
signature with the hope that it is unique enough and unlikely to
ever accidentally match this leftover garbage data in RAM. But
this approach is inherently unsafe, as can be demonstrated using
the following test program:

/***** A testcase for reproducing the problem ******/

void main(int argc, char *argv[])
{
    size_t size, i;
    uint32_t *buf;
    /* Allocate the buffer */
    if (argc < 2 || !(size = (size_t)atoi(argv[1]) * 1048576) ||
                    !(buf = malloc(size))) {
        printf("Need buffer size in MiB as a cmdline argument\n");
        exit(1);
    }
    /* Fill it with the Allwinner DRAM "magic" values */
    for (i = 0; i < size / 4; i++)
        buf[i] = 0xaa55aa55 + ((uintptr_t)&buf[i] / 4) % 64;
    /* Try to reboot */
    system("reboot");
    /* And wait */
    for (;;) {}
}
/***************************************************/

If this test program is run on the device (giving it a large
chunk of memory), then the DRAM size detection logic in u-boot
gets confused after reboot and fails to initialize DRAM properly.

A better approach is not to rely on luck and abstain from making
any assumptions about the properties of the leftover garbage
data in RAM. Instead just use a more reliable code for testing
whether two different addresses refer to the same memory location.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14 14:56:37 +01:00
Hans de Goede
08fd1479c7 sun8i: Add dram initialization support
Based on the register / dram_para headers from the Allwinner u-boot / linux
sources + the init sequences from boot0.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Hans de Goede
2367b44d0f sunxi: Use memcmp for mctl_mem_matches
Use memcmp for mctl_mem_matches instead of DIY.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Hans de Goede
5665f50e81 sunxi: Fill memory before comparing it when doing dram init on sun6i
The sun8i boot0 code fills the DRAM with a "random" pattern before comparing
it at different offsets to do columns, etc. detection. The sun6i boot0 code
does not do it, instead relying on the memory contents being random enough
to begin with for the memcmp to properly detect the wrap-around address, iow
it is working purely by chance. Since our sun6i dram code was modelled after
the boot0 code it contained the same issue.

This commit fixes this by filling the memory with a unique, distinct pattern.

The new mctl_mem_fill function this introduces is added as an inline helper
in dram.h, so that it can be shared with the sun8i dram code.

While at it move mctl_mem_matches to dram.h for re-use in sun8i too.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Hans de Goede
07f4fe7d7d sunxi: Move await_completion dram helper to dram.h
The await_completion helper is already copy pasted between the sun4i and sun6i
dram code, and we need it for sun8i too, so lets make it an inline helper in
dram.h, rather then adding yet another copy.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Hans de Goede
5af741f1e9 sun6i: Add a sigma_delta_enable paramter to clock_set_pll5()
The sun8i dram code sometimes wants to enable sigma delta mode,
add a parameter to allow this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Hans de Goede
66ebea06f7 sunxi: Add support for the rsb (Reduced Serial Bus)
sun8i (A23) introduces a new bus for communicating with the pmic, the rsb,
the rsb is also used to communicate with the pmic on the A80, and is
documented in the A80 user manual.

This commit adds support for this based on the rsb driver from the allwinner
u-boot sources.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Hans de Goede
ce881076fc sun6i: s/SUNXI_*P2WI*/SUN6I_*P2WI*/
The p2wi interface is only available on sun6i, adjust the gpio pinmux and
base address defines for it to reflect this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Hans de Goede
cac5b1cc0d sunxi: Add sunxi_get_sid helper function
On sun6i the SID is stored in the pmic, rather then in the SoC itself,
add a helper function to abstract this away.

This makes our MAC address generation code also work on sun6i.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Hans de Goede
fc3a832576 sunxi: mmc: Properly setup mod-clk and clock sampling phases
The sunxi mmc controller has both an internal clock divider, as well as
the divider in the mod0-clk for the mmc controller.

The internal divider cannot be used, as it conflicts with the setting of
clock sampling phases which is done in the mod0-clk, so it must be set to
0 (divide by 1).

For some reason while the kernel has had this correct from day one, the
u-boot sunxi mmc code has been using a fixed mod0-clk and setting its
internal divider depending on the desired speed. This is something which
we've inherited from the original Allwinner u-boot sources, but while this
has been fixed in Allwinner's own u-boot code at least for the A23 and later
upstream u-boot was still doing this wrong.

This commit fixes this, thereby also fixing mmc support not working reliable
on the A23 (which seems more sensitive to this) and possible also fixes some
other sunxi mmc issues.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Hans de Goede
10191ed098 sun6i: Add sunxi_get_ss_bonding_id() function
Add a sunxi_get_ss_bonding_id() function, and use it to differentiate between
the A31s and the A31.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Hans de Goede
eafec32000 sun6i: Add gmac support for sun6i boards
Hookup the gmac found on the sun6i / A31 SoCs.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-25 13:38:46 +01:00
Luc Verhaegen
2d7a084ba0 sunxi: video: Add simplefb support
Add simplefb support, note this depends on the kernel having support for
the clocks property which has recently been added to the simplefb devicetree
binding.

Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Use pre-populated simplefb node under /chosen as
 disussed on the devicetree list]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>.
2014-11-25 13:38:46 +01:00
Luc Verhaegen
7f2c521f90 sunxi: video: Add cfb console driver for sunxi
This adds a fixed mode hdmi driver for the sunxi platform. The fixed
mode is a relatively safe 1024x768, more complete EDID handling is
currently not provided. Only HDMI is supported today.

This code is enabled when HPD detects an attached monitor.

Current config is such that 8MB is shaved off at the top of the RAM.
This avoids several memory handling issues, most significant is the fact
that on linux on ARM you are not allowed to remap known RAM as IO. A
clued in display driver will be able to recycle this reserved RAM in
future though.

cfbconsole was chosen as it provides the most important functionality: a
working u-boot console, allowing for the debugging of certain issues
without the need for a UART.

Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Major cleanups and some small bugfixes]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-25 13:38:46 +01:00
Hans de Goede
0bd5125133 sunxi: Add video pll clock functions
This is a preparation patch for adding support for HDMI out.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-25 13:38:46 +01:00
Hans de Goede
9d4b7d0bc8 sun4i: Rename dram_clk_cfg to dram_clk_gate
The data sheet just calls it DRAM_CLK_REG, and on sun6i we've both a
dram_clk_cfg and dram_clk_gate, and the sun4i reg matches dram_clk_gate on
sun6i, so name it the same on sun4i.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-25 13:38:46 +01:00
Hans de Goede
76946dfe69 sun6i: ehci: Add sun6i ehci support
Add support for the 2 ehci controllers found on the sun6i (A31) soc.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Marek Vasut <marex@denx.de>
2014-11-13 14:49:02 +01:00
Hans de Goede
9a07eb0ba0 sun6i: Add dram initialization code
Add full support for dram initialization, using a fixed clock and autodetection
of the memory organization (numbers of channels, bus-width, etc.).

This is based on dram_sun6i.c and dram.h from u-boot in the Allwinner A31 SDK,
extended with extra initialization sequences and the autodetect algorithm
from boot0.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13 14:49:01 +01:00
Hans de Goede
bec72c7994 sun4i: Rename dram files to dram_sun4i.x
In preparation for adding sun6i dram support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13 14:49:01 +01:00
Hans de Goede
9d8a533e3f sun6i: Add cpucfg register definitions
Not used atm, for future use (e.g. PSCI).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13 14:49:01 +01:00
Hans de Goede
62c87ef2e9 sun6i: Add clock functions needed for SPL / DRAM init
Add clock_init_safe and clockset_pll5 functions, as these are needed for
SPL support resp. DRAM init (which is needed for SPL too).

Also add some extra clock register constant defines.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13 14:49:01 +01:00
Oliver Schinagl
3b10e6eb68 sun6i: Add new p2wi controller driver
The A31 uses a new push-pull two wire interface, which features higher
transfer speeds (upto 6 MHz) in theory. While the hardware can burst 8
bytes each time, this driver will only see very little use and thus is
limited to single byte transmission only.

Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13 14:49:01 +01:00
Simon Glass
bf38891af2 dm: sunxi: Add pinmux functions which take a bank parameter
With driver model we will have access to a bank pointer, so we want to
use it rather than converting back to a number, and then back to a
bank pointer. Add functions to provide this feature.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-05 13:09:58 +01:00
Ian Campbell
ed41e62f51 sunxi: Use CONFIG_MACH_SUN?I from Kconfig instead of CONFIG_SUN?I
Mostly automatic with:
    sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I)
followed by removing the relevant #defines from include/configs/sun?i.h by
hand.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-05 13:09:58 +01:00
Hans de Goede
9e54f6ee01 sunxi: Add clock_get_pll5p() function
This is a preparation patch for making the pll5 "p" divisor configurable
through Kconfig.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:37:24 +02:00
Chen-Yu Tsai
c757a50bd1 ARM: sunxi: Add support for using R_UART as console
The A23 only has UART0 muxed with MMC0. Some of the boards we
encountered expose R_UART as a set of pads.

Add support for R_UART so we can have a console while using mmc.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:39 +02:00
Chen-Yu Tsai
472ed0641e ARM: sunxi: Allow specifying module in prcm apb0 init function
The prcm apb0 controls multiple modules. Allow specifying which
modules to enable clocks and de-assert resets so the function
can be reused.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:39 +02:00
Hans de Goede
e373aad32a ARM: sunxi: Add support for R_PIO gpio banks
The A31, A23 and later SoCs have an extra pin controller, called CPUs_PIO
or R_PIO, which handles pin banks L and beyond.

Also add a clear description about SUNXI_GPIO_BANKS, stating it only
counts the number of pin banks in the _main_ pin controller.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: expanded commit message]
[wens@csie.org: add pin bank M and expand comments]
[wens@csie.org: add comment on SUNXI_GPIO_BANKS macro]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:39 +02:00
Chen-Yu Tsai
8ebe4f4292 ARM: sunxi: Add basic A23 support
The basic blocks of the A23 are similar to the A31 (sun6i). Re-use
sun6i code for initial clock, gpio, and uart setup.

There is no SPL support for A23, as we do not have any documentation
or sample code for DRAM initialization.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:39 +02:00
Chen-Yu Tsai
e637b30b9c mmc: sunxi: Add support for sun8i (A23)
The Allwinner A23 SoC has reset controls like the A31 (sun6i).
The FIFO address is also the same as sun6i.

Re-use code added for sun6i.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:39 +02:00
Chen-Yu Tsai
7f87ad354b ARM: sunxi: Add sun8i (A23) UART0 pin mux support
UART0 pin muxes on the A23 have a different function value.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:38 +02:00
Chen-Yu Tsai
78c396a113 ARM: sunxi: Fix reset command on sun6i/sun8i
The watchdog on sun6i/sun8i has a different layout.

Add the new layout and fix up the setup functions so that reset works.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
[ ijc -- removed sun5i workaround from sun6i/sun8i codepath as discussed ]
2014-10-24 09:35:38 +02:00
Chen-Yu Tsai
4cdefba86d ARM: sunxi: Add sun6i/sun8i timer block register definition
The RTC hardware has been moved out of the timer block on sun6i/sun8i.
In addition, there are more watchdogs available.

Also note that the timer block definition is not completely accurate
for sun5i/sun7i. Various blocks are missing or have been moved out.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:38 +02:00
Chen-Yu Tsai
2b679f9fa4 ARM: sunxi: Move watchdog register definitions to separate file
On later Allwinner SoCs, the watchdog hardware is by all means a
separate hardware block, with its own address range and interrupt
line.

Move the register definitions to a separate file to facilitate
supporting newer SoCs.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:38 +02:00
Hans de Goede
bbff84b3b0 sunxi: Use PG3 - PG8 as io-pins for mmc1
None of the known sunxi devices actually use mmc1 routed through PH, where
as some devices do actually use mmc1 routed through PG, so change the routing
of mmc1 to PG. If in the future we encounter devices with mmc1 routed through
PH, we will need to change things to be a bit more flexible.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:38 +02:00
Hans de Goede
e79c7c8810 sunxi: When we've both mmc0 and mmc2, detect from which one we're booting
sunxi SOCs can boot from both mmc0 and mmc2, detect from which one we're
booting, and make that one "mmc dev 0" so that a single u-boot binary can
be used for both the onboard eMMC and for external sdcards.

When we're booting from mmc2, we make it dev 0 because that is where the SPL
will load the tertiary payload (the actual u-boot binary in our case) from,
see: common/spl/spl_mmc.c, which has dev 0 hardcoded everywhere.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:38 +02:00
Chen-Yu Tsai
ba1e40fdd3 ARM: sun6i: Define UART0 pins for A31
UART0 is the default debug/console UART on the A31.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:38 +02:00
Hans de Goede
1d1bd42eb0 ARM: sunxi-mmc: Add mmc support for sun6i / A31
The mmc hardware on sun6i has an extra reset control that needs to
be de-asserted prior to usage. Also the FIFO address is different.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: use setbits_le32 for reset control, drop obsolete changes,
		rewrite different FIFO address handling, add commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:37 +02:00
Chen-Yu Tsai
14177e47e8 ARM: sun6i: Add clock support
This patch adds the basic clocks support for the Allwinner A31 (sun6i)
processor. This code will not been compiled until the build is hooked
up in a later patch. It has been split out to keep the patches manageable.

This includes changes from the following commits from u-boot-sunxi:

a92051b ARM: sunxi: Add sun6i clock controller structure
1f72c6f ARM: sun6i: Setup the UART0 clocks
5f2e712 ARM: sunxi: Enable pll6 by default on all models
2be2f2a ARM: sunxi-mmc: Add mmc support for sun6i / A31
12e1633 ARM: sun6i: Add initial clock setup for SPL
1a9c9c6 ARM: sunxi: Split clock code into common, sun4i and sun6i code
0b194ee ARM: sun6i: Properly setup the PLL LDO in clock_init_safe
b54c626 sunxi: avoid sr32 for APB1 clock setup.
68fe29c sunxi: remove magic numbers from clock_get_pll{5,6}
c89867d sunxi: clocks: clock_get_pll5 prototype and coding style
501ab1e ARM: sunxi: Fix sun6i PLL6 settings
37f669b ARM: sunxi: Fix macro names for mmc and uart reset offsets
61de1e6 ARM: sunxi: Correct comment for MBUS1 register in sun6i clock definitions

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: styling fixes reported by checkpatch.pl]
[wens@csie.org: drop unsupported SPL code block and unused gpio.h header]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:37 +02:00
Oliver Schinagl
174deb768c ARM: sun6i: Add support for the power reset control module found on the A31
The A31 has a new module called PRCM, or Power, Reset Control Module.
This module controls clocks and resets for RTC block modules, and also
PLL biasing in the main clock module.

This patch adds the register definitions, and also enables the clocks
and resets for the RTC block PIO (pin controller) and P2WI (push-pull
2 wire interface) which is used to talk to the PMIC.

Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: spacing fixes reported by checkpatch.pl]
[wens@csie.org: Use setbits helper in PRCM init function]
[wens@csie.org: rephrase commit message to explain what the hardware
		supports and what we actually enable]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:37 +02:00
Oliver Schinagl
93ce1e9dad ARM: sun6i: Add base address for the new controllers in A31
A31 has several new and changed memory address. This patch adds them.

Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:37 +02:00
Siarhei Siamashka
d755a5fb20 sunxi: dram: Configurable DQS gating window mode and delay
The hardware DQS gate training is a bit unreliable and does not
always find the best delay settings.

So we introduce a 32-bit 'dqs_gating_delay' variable, where each
byte encodes the DQS gating delay for each byte lane. The delay
granularity is 1/4 cycle.

Also we allow to enable the active DQS gating window mode, which
works better than the passive mode in practice. The DDR3 spec
says that there is a 0.9 cycles preamble and 0.3 cycle postamble.
The DQS window has to be opened during preamble and closed during
postamble. In the passive window mode, the gating window is opened
and closed by just using the gating delay settings. And because
of the 1/4 cycle delay granularity, accurately hitting the 0.3
cycle long postamble is a bit tough. In the active window mode,
the gating window is auto-closing with the help of monitoring
the DQS line, which relaxes the gating delay accuracy requirements.

But the hardware DQS gate training is still performed in the passive
window mode. It is a more strict test, which is reducing the results
variance compared to the training with active window mode.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
e044daa33e sunxi: dram: Add a helper function 'mctl_get_number_of_lanes'
It is going to be useful in more than one place.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
b8f7cb6ae3 sunxi: dram: Improve DQS gate data training error handling
The stale error status should be cleared for all sun4i/sun5i/sun7i
hardware and not just for sun7i. Also there are two types of DQS
gate training errors ("found no result" and "found more than one
possible result"). Both are handled now.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
1a9717cbb3 sunxi: dram: Configurable MBUS clock speed (use PLL5 or PLL6)
The sun5i hardware (Allwinner A13) introduced configurable MBUS clock
speed. Allwinner A13 uses only 16-bit data bus width to connect the
external DRAM, which is halved compared to the 32-bit data bus of sun4i
(Allwinner A10), so it does not make much sense to clock a wider
internal bus at a very high speed. The Allwinner A13 manual specifies
300 MHz MBUS clock speed limit and 533 MHz DRAM clock speed limit. Newer
sun7i hardware (Allwinner A20) has a full width 32-bit external memory
interface again, but still keeps the MBUS clock speed configurable.
Clocking MBUS too low inhibits memory performance and one has to find
the optimal MBUS/DRAM clock speed ratio, which may depend on many
factors:
    http://linux-sunxi.org/A10_DRAM_Controller_Performance

This patch introduces a new 'mbus_clock' parameter for the 'dram_para'
struct and uses it as a desired MBUS clock speed target. If 'mbus_clock'
is not set, 300 MHz is used by default to match the older hardcoded
settings.

PLL5P and PLL6 are both evaluated as possible clock sources. Preferring
the one, which can provide higher clock frequency that is lower or
equal to the 'mbus_clock' target. In the case of a tie, PLL5P has
higher priority.

Attempting to set the MBUS clock speed has no effect on sun4i, but does
no harm either.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
5c18384dea sunxi: dram: Re-introduce the impedance calibration ond ODT
The DRAM controller allows to configure impedance either by using the
calibration against an external high precision 240 ohm resistor, or
by skipping the calibration and loading pre-defined data. The DRAM
controller register guide is available here:

    http://linux-sunxi.org/A10_DRAM_Controller_Register_Guide#SDR_ZQCR0

The new code supports both of the impedance configuration modes:
   - If the higher bits of the 'zq' parameter in the 'dram_para' struct
     are zero, then the lowest 8 bits are used as the ZPROG value, where
     two divisors encoded in lower and higher 4 bits. One divisor is
     used for calibrating the termination impedance, and another is used
     for the output impedance.
   - If bits 27:8 in the 'zq' parameters are non-zero, then they are
     used as the pre-defined ZDATA value instead of performing the ZQ
     calibration.

Two lowest bits in the 'odt_en' parameter enable ODT for the DQ and DQS
lines individually. Enabling ODT for both DQ and DQS means that the
'odt_en' parameter needs to be set to 3.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Roman Byshko
06cdd94077 sunxi: add defines to control USB Host clocks/resets
The commit adds three defines which will be used in
the EHCI driver to enable USB clock and assert
reset controllers of the corresponding PHYs.

Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-31 15:37:22 +02:00
Ian Campbell
a6e50a88d8 ahci: provide sunxi SATA driver using AHCI platform framework
This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done
for sun7i only since I don't have access to any other sunxi platforms
with sata included.

The PHY setup is derived from the Alwinner releases and Linux, but is mostly
undocumented.

The Allwinner AHCI controller also requires some magic (and, again,
undocumented) DMA initialisation when starting a port.  This is added under a
suitable ifdef.

This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on
contents of Linux DTS files, including SATA power pin config taken from the
DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-31 15:37:22 +02:00
Ian Campbell
abce2c6220 sunxi: add gpio driver
This patch enables CONFIG_CMD_GPIO for the Allwinner (sunxi) platform as well
as providing the common gpio API (gpio_request/free, direction in/out, get/set
etc).

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Henrik Nordström <henrik@henriknordstrom.net>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2014-07-18 19:42:25 +01:00
Hans de Goede
6620377e4b sunxi: Add i2c support
Add support for the i2c controller found on all Allwinner sunxi SoCs,
this is the same controller as found on the Marvell orion5x and kirkwood
SoC families, with a slightly different register layout, so this patch uses
the existing mvtwsi code.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
[ ijc -- updated u-boot-spl-fel.lds ]
2014-07-18 19:41:30 +01:00
Hans de Goede
c7e79dec85 sunxi: Implement reset_cpu
There is no way to reset the cpu, so use the watchdog for this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-06 20:12:44 +01:00
Jeroen Hofstee
ed6c7f7f6e arm: spl: fix include guard
cc: Tom Rini <trini@ti.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-07-05 09:28:21 +02:00
Ian Campbell
e24ea55c04 sunxi: mmc support
On Mon, 2014-05-05 at 14:18 +0200, Stefan Roese wrote:
> > +	case 1:
> > +#if CONFIG_MMC1_PG

> Are you sure that this is correct and shouldn't be:
>
> +#ifdef CONFIG_MMC1_PG
>
> ?

It's "correct" in so far as it works (the boards.cfg config stuff
#defines things to 1), but I think you are right that it isn't the
preferred style. But...

> A quick scan through this patch series shows that this define
> is not set at all. Perhaps its outdated? Or is it used to support
> some other sunxi SoC? Not sure, perhaps it should be removed for
> now.

...I had thought that it was to support some other board which wasn't
being upstreamed right now, so eventually useful and harmless for now,
but I've just checked and it isn't actually used by any of the boards in
u-boot-sunxi.git. So rather than fix it to use #ifdef lets drop it.
Rather than resend the entire series, here is v5.1 of this patch.

> Other than this please add my:
>
> Reviewed-by: Stefan Roese <sr@denx.de>

Thanks!

8<---------------------------------

>From 20704e35a41664de5f516ed0e02981ac06085102 Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Fri, 7 Mar 2014 04:29:39 +0000
Subject: [PATCH v5.1 7/8] sunxi: mmc support

This adds support for the MMC controller on the Allwinner A20 (sun7i)
processor.

Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Cc: Aaron Maoye <leafy.myeh@allwinnertech.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25 16:26:43 +02:00
Ian Campbell
cba69eeeaa sunxi: add sun7i cpu, board and start of day support
This patch adds generic board, start of day and basic build system support for
the Allwinner A20 (sun7i) processor. This code will not been compiled until the
build is hooked up in a later patch. It has been split out to keep the patches
manageable.

Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Patrick Wood <patrickhwood@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25 16:12:40 +02:00
Ian Campbell
286c3c3a5e sunxi: add sun7i dram setup support
This patch adds DRAM initialisation support for the Allwinner A20 (sun7i)
processor. This code will not been compiled until the build is hooked up in a
later patch. It has been split out to keep the patches manageable.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25 16:12:30 +02:00
Ian Campbell
fe1b4db05e sunxi: add sun7i pinmux and gpio support
This patch adds the basic pinmux and gpio support for the Allwinner A20 (sun7i)
processor. This code will not been compiled until the build is hooked up in a
later patch. It has been split out to keep the patches manageable.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25 16:12:21 +02:00
Ian Campbell
643cf0ea02 sunxi: add sun7i clocks and timer support.
This patch adds the basic clocks and timer support for the Allwinner A20
(sun7i) processor. This code will not been compiled until the build is hooked
up in a later patch. It has been split out to keep the patches manageable.

Some of the code here is common to multiple sunxi subarchtectures, hence files
are named sun4i which is the earliest similar variant.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25 16:12:12 +02:00