V3M handles SDnH differently than other Gen3 SoCs, so let's add a
separate entry for that. This will allow better SDnH handling in the
future.
Based on Linux commit 627151b4966f ("mmc: renesas_sdhi: Flag
non-standard SDnH handling for V3M") by Wolfram Sang
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
It is unnecessary, so clean it up.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # update commit message, mention ES3.0
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Support R8A77961 M3-W+ SoC.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Still uses 0x3 for now, adjust the offset value to TMPPORT3 accordingly
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Adjust HS400 calibration tables based on Linux settings
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Further filter out HS400 support on certain SoCs.
Since M3-W r1.2 does not support HS400, drop the calibration table and
rename the one for M3-W r1.3 to r8a7796_rev13_calib_table
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Early ES revisions of M3-W SoCs requires 4-tap HS400. Reflect the status
from datasheet.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Drop 'core' parameter from gen3_clk_get_rate64_pll_mul_reg() function
as it is only used in debug print. No functional change except for the
debug print, which is disabled by default.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Since commit f7b4e4c094 ("clk: renesas: Synchronize R-Car Gen3 tables
with Linux 5.12"), the custom macros for RPC clocks were dropped.
Use pre-defined offset for RPC clocks, same as what Linux does, instead
of retrieving it from the macros
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add trivial reset driver extension to the CPG clock driver. The change
turns current CPG UCLASS_CLK driver instance into an UCLASS_NOP proxy
driver, which in turn binds both generic rcar3_clk UCLASS_CLK clock
driver as well as generic rcar_rst UCLASS_RESET reset driver to the
CPG DT node. This way, any other drivers which use the 'reset' DT
property can now obtain valid reset handle backed by a reset driver.
The clock tables have been updated to represent the CPG driver and only
implement the generic CPG proxy driver bind call, which binds the clock
and reset drivers.
The DM_RESET is now enabled for all R-Car Gen3 platforms.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for the R-Car M3-W+ (R8A77961) SoC.
R-Car M3-W+ is very similar to R-Car M3-W (R8A77960), which allows for
both SoCs to share a driver.
Based on Linux commit 2ba738d56db4 ("clk: renesas: r8a7796: Add R8A77961
CPG/MSSR support")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rename CONFIG_CLK_R8A7796 for R-Car M3-W (R8A77960) to
CONFIG_CLK_R8A77960, to avoid confusion with R-Car M3-W+ (R8A77961),
which will use CONFIG_CLK_R8A77961.
Based on Linux commit 92d1ebae9abf ("clk: renesas: Rename CLK_R8A7796
to CLK_R8A77960")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774E1 RZ/G2H clock tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774C0 RZ/G2E clock tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774B1 RZ/G2N clock tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774A1 RZ/G2M clock tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779A0 V3U clock tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Rename CLK_TYPE_R8A779A0_ to CLK_TYPE_GEN4_ to match the new
clock tables. Add CLK_TYPE_GEN4_SD, CLK_TYPE_GEN4_RPC and
CLK_TYPE_GEN4_RPCD2 macros and handling into Gen3 CPG core.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ clock tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Currently, SDnH is handled together with SDn. This caused lots of
problems, so we want SDnH as a separate clock. Introduce a dummy SDnH
type here which creates a fixed-factor clock with factor 1. That allows
us to convert the per-SoC CPG drivers while keeping the old behaviour
for now. A later patch then will add the proper functionality.
Based on Linux series by Wolfram Sang:
commit a31cf51bf6b4b ("clk: renesas: rcar-gen3: Add dummy SDnH clock"),
commit 1abd04480866c ("clk: renesas: rcar-gen3: Add SDnH clock"),
commit 63494b6f98f26 ("clk: renesas: r8a779a0: Add SDnH clock to V3U")
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Switch to gen3_clk_get_rate64
R-Car M3-W+ (R8A77961) is pin compatible with R-Car M3-W (R8A77960),
which allows for both SoCs to share a driver.
Based on Linux commit 708c69e9eacc ("pinctrl: sh-pfc: r8a7796: Add
R8A77961 PFC support") and 74ce7a8044b0 ("pinctrl: renesas: r8a7796:
Optimize pinctrl image size for R8A774A1")
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ PFC tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Note that the Kconfig option name has been updated to match the
Linux kernel Kconfig option name, from PINCTRL_PFC_R8A7796 to
PINCTRL_PFC_R8A77960 .
Also note that a new Kconfig option has been added to enable support
for R8A77961 M3-W+ , the Kconfig option name is PINCTRL_PFC_R8A77961 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7795 H3 PFC tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Note that the Kconfig option name has been updated to match the
Linux kernel Kconfig option name, from PINCTRL_PFC_R8A7795 to
PINCTRL_PFC_R8A77951 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7791 M2-W and R8A7793 M2-N PFC tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car PFC core with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Parts picked from
pinctrl: renesas: Synchronize R-Car Gen2/Gen3 tables with Linux 5.18.3
- Add pin groups for the green and high8 subsets of the Video IN pins
- Add MediaLB pins
- Add bias support for various SoCs
- Share more pin group data, to reduce size and ease review
- Miscellaneous cleanups, fixes and improvements.
This contains port of Linux kernel commit
6210905586ae ("pinctrl: renesas: Add shorthand for reserved register fields")
to handle negative entries in GROUP() macros correctly.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car device trees with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
The following script has been used for the synchronization:
$ for i in $(cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) ; do
if [ -e /linux-2.6/arch/arm64/boot/dts/renesas/$i ] ; then
cp /linux-2.6/arch/arm64/boot/dts/renesas/$i arch/arm/dts/ ;
elif [ -e /linux-2.6/arch/arm/boot/dts/$i ] ; then
cp /linux-2.6/arch/arm/boot/dts/$i arch/arm/dts/
else
echo "NOT FOUND: $i"
fi
done
$ git add $( ( cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) | tr " " "\n" | sed 's@^@arch/arm/dts/@g' )
Move the include/dt-bindings/{clk,clock}/versaclock.h header used by
the renesas boards to match Linux 6.1.y as well.
Keep arch/arm/dts/r8a774c0-u-boot.dtsi sdhi3 node as it is now used
by the arch/arm/dts/r8a774c0-cat874.dts board.
Pick s@spi-flash@flash@ change in arch/arm/dts/r8a779a0-falcon-u-boot.dts
from "ARM: dts: Synchronize R-Car V3U DTs with Linux 5.18.3" .
Adjust R8A77990 Ebisu CONFIG_SYS_MMC_ENV_DEV from 2 to 0 to reflect
the card enumeration in ebisu.dtsi /aliases DT node .
Adjust R8A7795 and R8A7796 ULCB CONFIG_SYS_MMC_ENV_DEV from 1 to 0 to
reflect the card enumeration in ulcb.dtsi /aliases DT node .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com> # r8a779a0-falcon-u-boot.dts
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> # r8a779a0-falcon-u-boot.dts
Unlike in Linux, -supply is not automatically appended to regulator
requests. Add it.
Fixes: 2645bc0e12 ("arm: layerscape: Add sfp driver")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SCFW has fixed a overflow issue in sc_rm_is_pad_owned API. This
requires u-boot to update API implementation, since it will cause
compatible issue. Otherwise all pad checking will have problem and
cause pad setting not continue.
Due to the compatible issue, the new u-boot only works with new
SCFW (API version: 1.21 and later).
old scfw + old u-boot: API overflow issue
old scfw + new u-boot, or new scfw + old u-boot: API compatible issue
new scfw + new u-boot: Working
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Jason Liu <Jason.hui.liu@nxp.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add support for HS400 in mode2timing array.
Add a quirk for Versal NET platform to indicate that HS400 is supported
through bit63 of capability register.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
HS400 is indicated in bit63 of capability register in few IP's.
Add a quirk to check this and add HS400 to host capabilities.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Check if the low level driver supports config_dll callback function and
call it if it does. Call with dll disable before calling set_clock and
with dll enable after it.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Add support for eMMC 5.1 for Versal NET platform
- Add new compatible string(xlnx,versal-net-5.1-emmc).
- Add CONFIG_ARCH_VERSAL_NET condition wherever required.
- Add DLL and Delay Chain mode support
- Add input and output tap delays for eMMC.
- Add Strobe select tap for HS400 mode.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Add more capable "bkops" command which allows enabling and disabling both
manual and automatic bkops. The existing 'mmc bkops-enable' subcommand is
poorly named to cover all the possibilities, hence the new-ish subcommand.
Note that both commands are wrappers around the same common code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Instead of waiting for empty FIFO condition before writing a
character, wait for non-full FIFO condition.
This helps in saving several tens of milliseconds during boot
(depending verbosity).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Fabio Estevam <festevam@denx.de>
The u-boot console may show some corrupted characters when
printing in board_init() due to reset or baudrate change
of the UART (probe) before the TX FIFO has been completely
drained.
To fix this issue, and in case UART is still running, we now
try to flush the FIFO before proceeding to UART reinitialization.
For this we're waiting for Transmitter Complete bit, indicating
that the FIFO and the shift register are empty.
flushing has a 4ms timeout guard, which is normally more than
enough to consume the FIFO @ low baudrate (9600bps).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The default configuration of the PMIC behavior makes the PMIC
power cycle most regulators on WDOG_B assertion. This power
cycling causes the memory contents of OCRAM to be lost.
Some systems neeeds some memory that survives reset and
reboot, therefore this patch is created.
The implementation is taken almost verbatim from Linux commit
2364a64d0673f ("regulator: pca9450: Make warm reset on WDOG_B assertion")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The DDR calibration tool for i.MX8M currently produces 3732 MTps rate in
lpddr4_timing.c , while the PHY code expects 3733 MTps rate. Support both
variants to avoid surprises where the system fails to boot.
Signed-off-by: Marek Vasut <marex@denx.de>
When a system has multiple XHCI controllers, some of the
properties described in the descriptor of the root hub (such as
the number of ports) might differ between controllers. Fix this
by switching from a single global hub descriptor to a hub
descriptor per controller.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This driver supports the PCIe controller on the Apple M1 and
M2 SoCs. The code is adapted from the Linux driver.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Systems such as Apple's M1 and M2 SoCs may have separate IOMMUs
for each PCIe root port. In this case the right IOMMU for a
PCI device behind a particular root port is described by an
"iommu-map" property in the device tree. Parse this property
and use it to find the right IOMMU device for PCI devices.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
An XHCI controller that sits behind an IOMMU needs to map and unmap
its memory buffers to do DMA. Implement this by inroducing new
xhci_dma_map() and xhci_dma_unmap() helper functions. The
xhci_dma_map() function replaces the existing xhci_virt_to_bus()
function in the sense that it returns the bus address in the case
of simple address translation in the absence of an IOMMU. The
xhci_bus_to_virt() function is eliminated by storing the CPU
address of the allocated scratchpad memory in struct xhci_ctrl.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Implement translation table support for all the variations of
Apple's DART IOMMU that can be found on Apple's M1 and M2 SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Test that the map and unmap operations work for devices that
have DMA translated by an IOMMU and devices that don't have
DMA translated by an IOMMU.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to support IOMMUs in non-bypass mode we need device ops
to map and unmap DMA memory. The map operation enters a mapping
for a region specified by CPU address and size into the translation
table of the IOMMU and returns a DMA address suitable for
programming the device to do DMA. The unmap operation removes
this mapping from the translation table of the IOMMU.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
There are no SPL/TPL variants of CONFIG_CLK_EXYNOS and
CONFIG_ARCH_APPLE, so switch from CONFIG_IS_ENABLED to
IS_ENABLED.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Don't define an empty version for pinconfig_post_bind(). Just guard the
call and let the linker garbage collection do the rest. This way, we
also don't have to do any guesswork.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Marek Vasut <marex@denx.de>
If CONFIG_PINCTRL_FULL is enabled, never fall back to the simple
implementation. pinctrl_select_state() is called for each device and it
is expected to fail. A fallback to the simple imeplementation doesn't
make much sense.
To keep the return code consistent, we need to change the -EINVAL (which
was ignored before) to -ENOSYS.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCY9PmzwAKCRDKSWXLKUoM
IYWxAJwNgiXtFT17pBy+1M0JvSWgyvWF3QCfTQG2Krnw0+d65PF5A7UFTDL7SZM=
=cMrc
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx chnages for v2023.04-rc1
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
In our system using ZynqMP with an external SGMII PHY it's necessary
to wait for the PCS link and auto negotiation to finish before the xfer
starts. Otherwise the first packet(s) might get dropped, resulting in a
delay at the start of the ethernet transfers.
This is only done when the PHY link is already up, which is done in
phy_startup(). As waiting for the PHY link bits via pcsstatus does not
make much sense, when the link is not available in general (e.g. no
cable connected).
This patch adds the necessary code including a minimal delay of 1 ms
which fixes problems of dropped first packages.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Katakam Harini <harini.katakam@amd.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20230125070908.1343256-1-sr@denx.de
Signed-off-by: Michal Simek <michal.simek@amd.com>
tuning_loop_counter is of char type, which is not capable of handling
the entire data range of this variable. This is pointed by below sparse
warning. Change datatype to int to fix this.
warning: comparison is always false due to limited range of data type.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230120053617.32463-5-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
There is a unused variable ret, due to which we are getting sparse warning
as below.
warning: variable 'ret' set but not used [-Wunused-but-set-variable].
Return ret incase of error.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230120053617.32463-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Binman positioning by ELF symbol
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmPTNLgRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreagiwgAr1Q+8qPghgomUK9cVjBuNzG2i88YWy7/
oitshEE73lm92kP4YIQrSm1ZBy6mm0A0wyy4pRLC0fFrovzAWq1o7xfUEkuhxyTV
pR7BiLPGUsHfL1cP4EuGSNMgrfX0QOddQgZTns4s7k4fbrFBLmTTa/+1jrU3AJNW
1FVfVSc4eMqHM5gD7mfqSHRsxrbZDHpzbJEKIMS1xkVy/BSQbDWtF1f6Lri3M9VT
Q7eNxFH5OptRAttcQreVNSNu28z00x0TuJNKLORXJa5AAxGW4yvNWgDFegU10NZc
ADTKaNDsDz4D//Ar3PSt+10eGWWKqrY9ClQwls4lJmJJTIqldf+QDw==
=l2A4
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jan23' of https://source.denx.de/u-boot/custodians/u-boot-dm
FIT improvements with split-elf, especially for Rockchip
Binman positioning by ELF symbol
Use a more accurate check for determining if the full format string will
be handled correctly, since SPL_USE_TINY_PRINTF can be disabled.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Infineon S25FS256T is 256Mbit Quad SPI NOR flash. The key features and
differences comparing to other Spansion/Cypress flash familes are:
- 4-byte address mode by factory default
- Quad mode is enabled by factory default
- Supports mixture of 128KB and 64KB sectors by OTP configuration
(this patch supports uniform 128KB only)
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Rename s25hx_t prefix to s25 so that the single set of fixup hooks can
support all other S25 families.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Acked-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Fix the issue where some flash chips like cypress S25HS256T return the
value of the same register over and over in DAC mode.
For example in the TI K3-AM62x Processors refer [0] Technical Reference
Manual there is a layer of digital logic in front of the QSPI/OSPI
Drive when used in DAC mode. This is part of the Flash Subsystem (FSS)
which provides access to external Flash devices.
The FSS0_0_SYSCONFIG Register (Offset = 4h) has a BIT Field for
OSPI_32B_DISABLE_MODE which has a Reset value = 0. This means, OSPI 32bit
mode enabled by default.
Thus, by default controller operates in 32 bit mode causing it to always
align all data to 4 bytes from a 4byte aligned address. In some flash
chips like cypress for example if we try to read some regs in DAC mode
then it keeps sending the value of the first register that was requested
and inorder to read the next reg, we have to stop and re-initiate a new
transaction.
This causes wrong register values to be read than what is desired when
registers are read in DAC mode. Hence if the data.nbytes is very less
then prefer STIG mode for such small reads.
[0] https://www.ti.com/lit/ug/spruiv7a/spruiv7a.pdf
Tested-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
[jagan: add tab space for comments]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Setup the Addr bit field while issuing register reads in STIG mode. This
is needed for example flashes like cypress define in their transaction
table that to read any register there is 1 cmd byte and a few more address
bytes trailing the cmd byte. Absence of addr bytes will obviously fail
to read correct data from flash register that maybe requested by flash
driver because the controller doesn't even specify which address of the
flash register the read is being requested from.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cypress defines two flavors of configuration registers, volatile and
non volatile, and both use the same bit fields. Rename the bitfields in
the configuration registers so that they can be used for both flavors.
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Introduce Socionext F_OSPI controller driver. This controller is used to
communicate with slave devices such as SPI flash memories. It supports
4 slave devices and up to 8-bit wide bus, but supports master mode only.
This driver uses spi-mem framework for SPI flash memory access, and
can only operate indirect access mode and single data rate mode.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Use log_warning() instead of printf() to print out driver information
Signed-off-by: Pengfei Fan <fanpengfei1@eswincomputing.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Fix some typos in spi drivers
Signed-off-by: Pengfei Fan <fanpengfei1@eswincomputing.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This syncs drivers/ddr/marvell/a38x/ with the master branch of repository
https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git
up to the commit "mv_ddr: a3700: Use the right size for memset to not overflow"
d5acc10c287e40cc2feeb28710b92e45c93c702c
This patch was created by following steps:
1. Replace all a38x files in U-Boot tree by files from upstream github
Marvell mv-ddr-marvell repository.
2. Run following command to omit portions not relevant for a38x, ddr3, and ddr4:
files=drivers/ddr/marvell/a38x/*
unifdef -m -UMV_DDR -UMV_DDR_ATF -UCONFIG_APN806 \
-UCONFIG_MC_STATIC -UCONFIG_MC_STATIC_PRINT -UCONFIG_PHY_STATIC \
-UCONFIG_PHY_STATIC_PRINT -UCONFIG_CUSTOMER_BOARD_SUPPORT \
-UCONFIG_A3700 -UA3900 -UA80X0 -UA70X0 -DCONFIG_ARMADA_38X -UCONFIG_ARMADA_39X \
-UCONFIG_64BIT $files
3. Manually change license to SPDX-License-Identifier
(upstream license in upstream github repository contains long license
texts and U-Boot is using just SPDX-License-Identifier.
After applying this patch, a38x, ddr3, and ddr4 code in upstream Marvell github
repository and in U-Boot would be fully identical. So in future applying
above steps could be used to sync code again.
The only change in this patch are:
1. Some fixes with include files.
2. Some function return and basic type defines changes in
mv_ddr_plat.c (to correct Marvell bug).
3. Remove of dead code in newly copied files (as a result of the
filter script stripping out everything other than a38x, dd3, and ddr4).
Reference:
"ddr: marvell: a38x: Sync code with Marvell mv-ddr-marvell repository"
107c3391b9
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This contains some fixes, and the first bunch of some clean up patches
to get rid of legacy GPIO and PMIC code.
Highlight is the DM AXP PMIC driver, which is required to convert some
drivers over to use DM regulators, and also is required to get rid
of some less optimal PMIC setup code in Trusted Firmware. This isn't
enabled by any defconfig yet, but can be enabled manually and works. For
the full glory some patches are still missing, and this requires more
testing, which would be simpler if the core code is upstream.
We need extensions to be set up before we start trying to boot any of the
bootdevs. Add a new priority before all the others for tht sort of thing.
Also add a 'none' option, so that the first one is not 0.
While we are here, comment enum bootdev_prio_t fully and expand the test
for the 'bootdev hunt' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a bootdev for SPI flash so that these devices can be used with
standard boot. It only supports loading a script.
Add a special case for the label, since we want to use "spi", not
"spi_flash".
Enable the new bootdev on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
The controller indicates the number of ports but also has a port map
which specifies which ports are actually valid. Make use of this to
avoid trying to send commands to an invalid port.
This avoids a crash on some controllers.
Signed-off-by: Simon Glass <sjg@chromium.org>
The test code for virtio is fairly simplistic and does not actually create
a block device. Add a way to specify the device type in the device tree.
Add a block device so that we can do more testing.
Signed-off-by: Simon Glass <sjg@chromium.org>
This has a special meaning in driver model. There is clearly a device, so
it does not make sense to return this error code. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this only unbinds block devices of a certain type. But SCSI
device can have different types of children, including bootdevs.
Unbind all children so tht everything is clean and ready for a new scan.
Signed-off-by: Simon Glass <sjg@chromium.org>
This should be allocated so that it does not go out of scope. Fix this and
set the log category while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a hunter for MMC. This doesn't do anything at present, since MMC is
currently set up when U-Boot starts. If MMC moves to lazy init then we can
add a hunter function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a hunter for USB which enumerates the bus to find new bootdevs.
Update the tests and speed up bootdev_test_prio() while we are here, by
dropping the USB delays.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since usb_find_and_bind_driver() allocates the device name it should tell
driver about that, to avoid memory leaks. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The code in these functions turns out to often be the same. Add a default
get_bootflow() function and allow the drivers to select it by setting
the method to NULL.
This saves a little code space.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present MMC uses the bootdev_setup_for_dev() function to set up the
bootdev. This is because MMC only has one block-device child, so does not
need to worry about naming of the bootdev.
However this inconsistency with other bootdevs that use block devices is a
bit annoying. The only real reason for it is to have a name like
'mmc0.bootdev' instead of 'mmc0.blk.bootdev'.
Update bootdev_setup_sibling_blk() to drop '.blk' from the name where it
appears, thus removing the only reason to use the bootdev_setup_for_dev().
Switch MMC over to the subling function.
Signed-off-by: Simon Glass <sjg@chromium.org>
When running multiple tests the mmc emulator calls malloc() to obtain the
memory for its disk image. Since the memory is not cleared, it is possible
that it happens to contain a partition table.
The dm_test_part() test (for one) relies on mmc0 being empty on startup.
Zero the memory to ensure that it is.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently HDMI controller MMIO address is hardcoded. Change that so
address is read from DT node. That will make adding support for new
variants a bit easier.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Currently the sunxi dw-hdmi driver is probed unconditionally,
even if there is no such device.
Switch the driver to probing via a compatible string. This brings many
benefits; the driver is only probed when needed, and now it can read the
DT node.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Add clock/reset definitions for display-related peripherals, including
the display engine, TCONs, and DSI and HDMI encoders, so those drivers
can be converted to DM clock consumers instead of directly manipulating
the CCU registers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that a regulator driver exists for this PMIC, hook it up to the
device tree "regulators" subnodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This driver handles most voltage regulators found in X-Powers AXP PMICs.
It is based on, and intended to replace, the regulator driver in TF-A.
AXP PMIC regulators can be divided into 6 categories:
- Switches without voltage control => fully supported.
- Single linear range => fully supported.
- Two linear ranges, "step" and "2 * step" => fully supported.
- Two linear ranges, "step" and "5 * step" => only the first range is
supported. No boards are known to use the second range.
- Non-linear voltage values => fully supported.
- LDOs shared with GPIO pins => not supported.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Subordinate regulator drivers can use this enumerated ID instead of
matching the compatible string again.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As the SPL code for sunxi boards does not use the driver model, we have
two mmc_ops structures, one for DM, one for non-DM. The actual hardware
access code is shared, with the respective callback functions using that
common code.
To make this more obvious and easier to read, reorder the functions to
group them: we first have the common code, then the non-DM bits, and
the proper DM implementation at the end.
Also document this structure in the comment at the beginning of the file.
No functional change intended.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
The sunxi MMC code does not use the DM in the SPL, as we don't have a
device tree available that early, also no space for it.
This also means we cannot access the card-detect GPIO information from
there, so we have Kconfig symbols called CONFIG_MMCx_CD_PIN, which each
board has to define. This is a burden, also requires extra GPIO code in
the SPL.
As the SPL is the natural successor of the BootROM (from which we are
loaded), we can actually ignore the CD pin completely, as this is what
the BootROM does as well: CD GPIOs are board specific, but the BootROM
is not, so accesses the MMC devices anyway.
Also, as we must have been loaded from an MMC device when reaching this
code, there must have been a card in the slot.
Remove the card detect code from the non-DM implementation of the sunxi
MMC driver, to get rid of this unneeded code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In imx_watchdog, clean up the comment to just note the range now, as we
do not need to set the default here as Kconfig does this for us. For
ulp_wdog, set the default value via Kconfig instead.
Cc: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
For this legacy driver, the only user sets these values in Kconfig, so
we can remove them from the header.
Signed-off-by: Tom Rini <trini@konsulko.com>
As this is used on both ARM and PowerPC platforms, this needs to be
asked in arch/Kconfig.nxp. Set the PowerPC defaults based on
arch/powerpc/include/asm/config_mpc85xx.h and remove the default set in
drivers/mtd/nand/raw/fsl_ifc_nand.c
Signed-off-by: Tom Rini <trini@konsulko.com>
Set the default for MV88E61XX_FIXED_PORTS to 0x0 in Kconfig, and move
the comment from code to the help to explain what this does.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This variable has never been configured to another value at present, and
was not converted to Kconfig. Opt instead to rename this to
MUSB_TIMEOUT.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This is always defined to 5, so use that as the default.
Cc: Michal Simek <michal.simek@amd.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
This driver is used on both m68k, where CONFIG_SYS_IMMR is not used, and
PowerPC an ARM where it is. Abstract this to a new value rather than
re-defining a CONFIG symbol on m68k.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove some CONFIG symbols and related comments, etc, that are unused
within the code itself at this point.
Signed-off-by: Tom Rini <trini@konsulko.com>
arch/mach-meson has some custom usb logic, in particular:
* on board_usb_init(), we force USB_DR_MODE_PERIPHERAL
* on board_usb_cleanup(), we force USB_DR_MODE_HOST
With DM_USB_GADGET=y, board_usb_init/cleanup() are no
longer used when we call usb_gadget_initialize().
Instead, the generic (from udc-uclass) initialization/release is
called, which itself calls the controller driver's probe()/remove().
Therefore, enabling DM_USB_GADGET=y will mean that this mode
switching will break.
To prepare for enabling DM_USB_GADGET, perform the mode switching
when the "amlogic,meson-g12a-usb" (dwc2) driver is
probed()/removed() instead.
This is achieved via the glue driver, which gets notified each time one
of its children is probed()/removed.
Note: this change should be harmless without DM_USB_GADGET=y
because the amlogic-g12a-usb driver is not probed via driver model.
Thanks for Mattijs for the original work at [1].
[1] https://lore.kernel.org/all/20221024-meson-dm-usb-v1-1-2ab077a503b9@baylibre.com/
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230117-u-boot-usb-gxl-otg-dm-v1-1-2853f6d75b06@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
When comparing UUIDs for discovered services we only compare up to the
ptr size instead of the entire UUID
Fixes: 94ccfb78a4 ("drivers: tee: optee: discover OP-TEE services")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
commit fe8a4ed011 ("tee: optee: discover services dependent on tee-supplicant")
is trying to automatically scan and add TAs that are presented on pseudo
bus from the secure world.
In order to be able to list and compare the scanned devices the available drivers
have to register themselves on the op-tee service list.
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
If we fail to probe the optee-rng device, we print a wrong message
referring to the firmware tpm.
Fixes: 476a3d58df ("tee: optee: don't fail probe because of optee-rng")
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmPIpV4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZuqwgA0UpYQEX6/MegzHSCIx3AMT4rCF1Ytitr
LS4Cbvj1Q09Rt9jriW7wAV5AobVPwGf2L5SVcnWv2I9+MmypDIXEe8HIrt2fRFu9
bzn/2GOzXczuXqPFa/CWOUwjvCzTb8Sl9NtRszrP5NvOzuN15x00ZUYaXFO7fgsB
zZMzOKxemwjdtLaox+x+VIJ95HMDEkYrWTAqTPg74CNVSjRbbLNqNq0zqkHB8SnH
ubgphtIKYItTeIXcfIa9V4LeQp0ZitkzSfAibX+nIPCMPg9jbG9MrQQ+VvSZDjnM
y8wa8gFj47Ek+gGNFXMHIpO6tBd83uHRgtf2x+zhcovLELYnZ6fDGw==
=1K6m
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-18jan23' of https://source.denx.de/u-boot/custodians/u-boot-dm
convert rockchip to use binman
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
This breaks chromebook_coral and it is also not how things should work. If
a board needs to bind GPIOs as part of a pinctrl driver this can be done
during the bind step, if needed.
We cannot probe pinctrl devices when binding as a rule, since it cannot be
supported on some platforms.
The bind and probe steps are separate in U-Boot and they should remain
separate.
This reverts commit f9ec791b5e.
Signed-off-by: Simon Glass <sjg@chromium.org>
The event framework is just that, a framework. Enabling it by itself
does nothing, so we shouldn't ask the user about it. Reword (and correct
typos) around this the option and help text. This also applies to
DM_EVENT and EVENT_DYNAMIC. Only EVENT_DEBUG and CMD_EVENT should be
visible to the user to select, when EVENT is selected.
With this, it's time to address the larger problems. When functionality
uses events, typically via EVENT_SPY, the appropriate framework then
must be select'd and NOT imply'd. As the functionality will cease to
work (and so, platforms will fail to boot) this is non-optional and
where select is appropriate. Audit the current users of EVENT_SPY to
have a more fine-grained approach to select'ing the framework where
used. Also ensure the current users of event_register and also select
EVENT_DYNAMIC.
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reported-by: Oliver Graute <Oliver.Graute@kococonnector.com>
Reported-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Fixes: 7fe32b3442 ("event: Convert arch_cpu_init_dm() to use events")
Fixes: 42fdcebf85 ("event: Convert misc_init_f() to use events")
Fixes: c5ef202557 ("dm: fix DM_EVENT dependencies")
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
To quote the author:
So far standard boot lacks a boot menu, although it is possible to create
a rudimentary one using the existing 'bootmenu' command.
Even then, this text-based menu offer only basic functionality and does
not take full advantage of the displays which are common on many devices.
This series provides a 'bootflow menu' command which allows the user to
select from the available bootflows. An attempt is made to show the name
of the available operating systems, by reading more information into the
bootflow. A logo can be read also, where supported, so that this can be
presented to the user when an option is highlighted.
Full use is made of TrueType fonts, if enabled. For cases where only a
serial console is available, it falls back to a simple text-based menu.
All of this is implementing using a new 'expo' construct, a collection of
scenes (like menu screens) which can be navigated by the user to view
information and select options. This is fairly general and should be able
to cope with a wider array of use cases, with less hacking of the menu
code, such as is currently needed for CMD_BOOTEFI_BOOTMGR.
Of course it would be possible to enhance the existing menu rather than
creating a new setup. Instead it seems better to make the existing menu
use expo, if code space permits. It avoids the event-loop problem and
should be more extensible, given its loosely coupled components and use of
IDs instead of pointers. Further motivation is provided in the
documentation.
For now the CLI keypress-decoding code is split out to be used by the new
menu. The key codes defined by menu.h are reused also.
This is of course just a starting point. Some ideas for future work are
included in the documentation.
arch/mach-meson has some custom usb logic, in particular:
* on board_usb_init(), we force USB_DR_MODE_PERIPHERAL
* on board_usb_cleanup(), we force USB_DR_MODE_HOST
With DM_USB_GADGET=y, board_usb_init/cleanup() are no
longer used when we call usb_gadget_initialize().
Instead, the generic (from udc-uclass) initialization/release is
called, which itself calls the controller driver's probe()/remove().
Therefore, enabling DM_USB_GADGET=y will mean that this mode
switching will break.
To prepare for enabling DM_USB_GADGET, perform the mode switching
when the "amlogic,meson-g12a-usb" (dwc2) driver is
probed()/removed() instead.
This is achieved via the glue driver, which gets notified each time one
of its children is probed()/removed.
Note: this change should be harmless without DM_USB_GADGET=y
because the amlogic-g12a-usb driver is not probed via driver model.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20221024-meson-dm-usb-v1-1-2ab077a503b9@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
It was noticed that Clearfog is currently broken with this newly
introduced early_init_done() function. Apparently the timer is enabled
here when U-Boot is run but not configured - at least not correctly.
Resulting in a hangup in the timer reading functions.
To fix this, also read the value of the reload register and check it's
value with the one written to by U-Boot. Only if this matches, the
init has already been done.
Fixes: 5387b093cb ("timer: orion-timer: Fix problem with early static variable")
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Pali Rohár <pali@kernel.org>
Cc: Martin Rowe <martin.p.rowe@gmail.com>
Cc: Tony Dinh <mibodhi@gmail.com>
Cc: Pali Rohár <pali@kernel.org>
Cc: Michael Walle <michael@walle.cc>
Support for fonts currently depends on the type of vidconsole in use. Add
two new methods to enumerate fonts and to set the font.
Fix a few other method comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not generally needed unless EFI_LOADER is used. Adjust the default
setting to reduce the size of the U-Boot build.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should use the cmd/ directory for commands rather than for common code
used elsewhere in U-Boot. Move the common 'source' code into
image-board.c to achieve this.
The image_source_script() function needs to call run_command_list() so
seems to belong better in the command library. Move and rename it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add clock driver support for Rockchip RV1126 SoC.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some pins in rockchip are routed via Top GRF and PMU GRF
instead of direct regmap.
Add support to handle all these routing paths so that the
SoC pinctrl drivers will use them accordingly.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Control the ddr init print messages via RAM_ROCKCHIP_DEBUG
instead of printing by default.
This gives an option to configs to enable these prints or
not.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add full ddr pctl registers and bit masks for px30.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
DDR chip capacity is computed based on GRF split in some
Rockchip SoC's like PX30 and RV1126.
Add split argument in ddr print info so-that the respective
ddr driver will pass the grf split.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
We have common ddr types in rockchip or in general. So use
the common ddr type names instead of per Rockchip SoC to
avoid confusion.
The respective ddr type names will use on the associated
ddr SoC driver as these drivers are built per SoC at a time.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ram-uclass is building irrespective of whether TPL_DM
or SPL_DM is enabled. So control the ram uclass build
based on TPL/SPL_DM.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the PCLK_WDT_NS clock to px30_clk_enable so that the watchdog driver
can probe since it wants to enable this clock.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Pullup is used by the usb framework in order to do software-controlled
usb_gadget_connect() and usb_gadget_disconnect().
Implement pullup() for dwc2 using the SOFT_DISCONNECT bit in the dctl
register:
* when pullup is on, clear SOFT_DISCONNECT
* when pullup is off, set SOFT_DISCONNECT
This is especially useful when a gadget disconnection is initiated but
no board_usb_cleanup() is called.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The patch fixes the following error when updating a BSH SMM S2 board:
3:72>Start Cmd:FB[-t 8000]: ucmd nand write ${loadaddr} nanddtb ${filesize}
3:72>Okay (0.023s)
3:72>Start Cmd:FB: reboot
3:72>Fail Bulk(R):LIBUSB_ERROR_IO(0s)
The "fastboot reboot" command detaches the USB when it still needs to be
used. So let's detach the USB just before the reset.
CC: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Fixes: 5f7e01e9d5 ("usb: gadget: fastboot: detach usb on reboot commands")
Suggested-by: Michael Trimarchi <michael@amarulasolutions.com>
Co-developed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add calibration support for stm32-adc
Linux kernel v6.1 DT synchronization for stm32mp151.dtsi
stm32mp157a-dk1-scmi-u-boot.dtsi update
Add support of OP-TEE and STM32MP13x in bsec driver
ECDSA various fixes for stm32mp
-----BEGIN PGP SIGNATURE-----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=SNID
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20230113' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add driver to manage onboard hub supplies
Add calibration support for stm32-adc
Linux kernel v6.1 DT synchronization for stm32mp151.dtsi
stm32mp157a-dk1-scmi-u-boot.dtsi update
Add support of OP-TEE and STM32MP13x in bsec driver
ECDSA various fixes for stm32mp
The gpio_hog_probe_all() functionality can be perfectly well replaced by
DM_FLAG_PROBE_AFTER_BIND DM flag, which would trigger .probe() callback
of each GPIO hog driver instance after .bind() and thus configure the
hogged GPIO accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Currently, dm_probe_devices checks that the flags of the device contains
DM_FLAG_PRE_RELOC. However DM_FLAG_PRE_RELOC is a driver - and not a
device - flag. This means that the check in pre_reloc_only mode would
always fail.
Instead, what was aimed to be checked is that either the driver of the
device has the flag set, or that the device has the u-boot,dm-pre-reloc
Device Tree property set.
So let's fix the check to allow u-boot,dm-pre-reloc devices to be
probed.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
This adds a new method to load Fman firmware from a filesystem. This
allows users to use regular files instead of hard-coded offsets for the
firmware.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
In order to read the firmware from the filesystem, we need a file name.
Read the firmware name from the device tree, using the firmware-name
property. This property is commonly used in Linux to determine the
correct name to use (and can be seen in several device trees in U-Boot).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The fs_loader device is used to pull in settings via the chosen node.
However, there was no library function for this, so arria10 was doing it
explicitly. This function subsumes that, and uses ofnode_get_chosen_node
instead of navigating the device tree directly. Because fs_loader pulls
its config from the environment by default, it's fine to create a device
with nothing backing it at all. Doing this allows enabling
CONFIG_FS_LOADER without needing to modify the device tree.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This commit introduces Random number generator to uboot. It uses DCP
driver for number generation.
RNG driver can be invoked by using below command on uboot prompt:-
rng <number of bytes>
Signed-off-by: Kshitiz Varshney <kshitiz.varshney@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support of offset and linear calibration for STM32MP15.
The calibration is performed once at probe. The ADC is set in power on
state for calibration. It remains in this state after calibration,
to give to the kernel the opportunity to retrieve calibration data,
directly from the ADC.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The main issue the driver addresses is that a USB hub needs to be
powered before it can be discovered. This is often solved by using
"regulator-always-on".
This driver is inspired by the Linux v6.1 driver. It only enables (or
disables) the hub vdd (3v3) supply, so it can be enumerated.
Scanning of the device tree is done in a similar manner to the sandbox,
by the usb-uclass. DT part looks like:
&usbh_ehci {
...
#address-cells = <1>;
#size-cells = <0>;
hub@1 {
compatible = "usb424,2514";
reg = <1>;
vdd-supply = <&v3v3>;
};
};
When the bus gets probed, the driver is automatically probed/removed from
the bus tree, as an example on stm32:
STM32MP> usb start
starting USB...
STM32MP> dm tree
Class Index Probed Driver Name
-----------------------------------------------------------
usb 0 [ + ] ehci_generic | |-- usb@5800d000
usb_hub 0 [ + ] usb_onboard_hub | | `-- hub@1
usb_hub 1 [ + ] usb_hub | | `-- usb_hub
STM32MP> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 2mA)
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
sata_sil.c is PCI driver and without CONFIG_PCI is building of U-Boot failing:
LD u-boot
ld.bfd: drivers/ata/sata_sil.o: in function `sil_exec_cmd':
drivers/ata/sata_sil.c:148: undefined reference to `dm_pci_phys_to_bus'
ld.bfd: drivers/ata/sata_sil.o: in function `sil_pci_probe':
drivers/ata/sata_sil.c:687: undefined reference to `dm_pci_get_bdf'
ld.bfd: drivers/ata/sata_sil.c:691: undefined reference to `dm_pci_read_config16'
ld.bfd: drivers/ata/sata_sil.c:701: undefined reference to `dm_pci_map_bar'
ld.bfd: drivers/ata/sata_sil.c:704: undefined reference to `dm_pci_map_bar'
ld.bfd: drivers/ata/sata_sil.c:713: undefined reference to `dm_pci_write_config16'
ld.bfd: drivers/ata/sata_sil.c:717: undefined reference to `dm_pci_read_config16'
ld.bfd: drivers/ata/sata_sil.o: in function `sil_cmd_identify_device':
drivers/ata/sata_sil.c:256: undefined reference to `dm_pci_phys_to_bus'
ld.bfd: drivers/ata/sata_sil.o: in function `sil_sata_rw_cmd':
drivers/ata/sata_sil.c:330: undefined reference to `dm_pci_phys_to_bus'
ld.bfd: drivers/ata/sata_sil.o: in function `sil_sata_rw_cmd_ext':
drivers/ata/sata_sil.c:377: undefined reference to `dm_pci_phys_to_bus'
make: *** [Makefile:1778: u-boot] Error 1
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This adds the UUU UCmd functionality as an OEM command. While the
fastboot tool allows sending arbitrary commands as long as they are
prefixed with "oem". This allows running generic U-Boot commands over
fastboot without UUU, which is especially useful when not using USB.
This is really the route we should have gone in the first place when
adding these commands.
While we're here, clean up the UUU Kconfig a bit.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Much of the fastboot code predates the introduction of Kconfig and
has quite a few #ifdefs in it which is unnecessary now that we can use
IS_ENABLED() et al.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3l
In U-Boot driver model the devices can be referenced by
phandle in the U-Boot configuration nodes.
Without a valid node provided during the bind, the driver
associated to OP-TEE TA can't be referenced.
For example to force the sequence number with alias
(.flags = DM_UC_FLAG_SEQ_ALIAS)
aliases {
rng0 = &optee;
};
or other configuration:
board-sysinfo {
compatible = "vendor,sysinfo-board";
ramdom = <&optee>;
}
With this patch all drivers bound from OP-TEE service
discovery are now associated are associated to OP-TEE
node, allowing to identify by phandle the driver
provided by the TA for one UCLASS without modifying
device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This adds an NVMEM reboot mode driver, similar to Linux's
implementation. This allows using the same device tree binding for Linux
and U-Boot in most cases.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for reading the battery-backed memory present on these
RTCs. This modifies the read/write methods to access the RAM instead of
raw register offsets. No one was using these in-tree, so we should be
fine changing them.
We use the "standard" address space window to access the RAM. The
extension RAM address register has some reserved bits, but we write the
whole thing for simplicity (as these bits default to 0).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
- rawnand: omap_gpmc: driver model support
-----BEGIN PGP SIGNATURE-----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=Agfn
-----END PGP SIGNATURE-----
Merge tag 'u-boot-nand-20230108' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash into next
Pull request for u-boot-nand-20230108
- rawnand: omap_gpmc: driver model support
Support u-boot driver model. We still retain
support legacy way of doing things if ELM_BASE
is defined in <asm/arch/hardware.h>
We could completely get rid of that if all
platforms defining ELM_BASE get rid of that definition
and enable CONFIG_SYS_NAND_SELF_INIT and are verified
to work.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Link: https://lore.kernel.org/all/20221220102203.52398-9-rogerq@kernel.org
Link: https://lore.kernel.org/all/CABGWkvrvKiVA_yaDnHJcHEKwc+pEuLdz=i6HQEY0oJQvohCUsw@mail.gmail.com
The symbol is required for NAND support in SPL when using
OMAP_GPMC driver.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-7-rogerq@kernel.org
Enables SPL NAND support for ARCH_K3 by enabling
SPL_NAND_INIT and SPL_SYS_NAND_SELF_INIT.
Legacy OMAP2plus platforms still rely on SPL_NAND_AM33XX_BCH
instead.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-6-rogerq@kernel.org
Adds driver model support.
We need to be able to self initialize the NAND controller/chip
at probe and so enable CONFIG_SYS_NAND_SELF_INIT.
Doing so requires nand_register() API which is provided by nand.c
and needs to be enabled during SPL build via CONFIG_SPL_NAND_INIT.
But nand.c also provides nand_init() so we need to get rid of nand_init()
in omap_gpmc driver if CONFIG_SPL_NAND_INIT is set.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-5-rogerq@kernel.org
nand_bbt.c is not being built with the nand_base driver during SPL
build. This results in build failures if we try to access any nand_bbt
related functions.
Don't use any nand_bbt functions for SPL build.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-3-rogerq@kernel.org
The BCH detection hardware can generate ECC bytes for multiple
sectors in one go. Use that feature.
correct() only corrects one sector at a time so we need to call it
repeatedly for each sector.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-2-rogerq@kernel.org
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmO2mnEcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBAOB/4y7e9y0jdKSWDwMdZj
enXK/U/GREFyuiSdadil0aJl9WfayjwZkh7uHSTj4pi9ApNivfoqsL7WZYpJxhRD
WlpNhs3TZ70i8CgKUosdzcpquAQZUZhg6iV5DCObrK6yNJRGOXLIwMOd+vw/Xz6/
YTGqzivEDMBuH/9HLuC0m+26PEpff8nenNEjC2k8ssG26ojLz7oCQh2HoHcSgNRc
HkEYlFJ/Le8kM8Ak2F3ebmsfgMTnFrRVwV1BsZa5vO0BrMYgJCORsl7Cnfcw6/2N
LEHG7kwlSorJeETn/gkLiZ+NyqzU+oFH0jGRZ5Ciqg1qcCO3k9yBMgWQzd7nTL6C
5oZA
=Ocdd
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.04 cycle:
This feature set includes the new DM-based NAND flash driver (old non-DM
driver is still kept for backwards compatibility), and the move to DM
NAND flash driver for sam9x60ek board. Feature set also includes
devicetree alignment for sama7g5 with Linux, devicetree alignment on USB
with Linux for all boards (sama5, sam9x60), chip id for sama7g5, minor
configs and tweaks.
This reverts commit ed6251187a.
Superseded by "cmd: pxe_utils: Limit fdtcontroladdr usage to non-fitImage"
which is less heavy-handed approach and retains part of the original
behavior for non-fitImage.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
The uniphier i2c block can recognize some handshake errors.
But driver handles all error detections as no error if no timeout.
So this makes unrecoverable state.
This replaces the return values with the right ones to tell the i2c
framework the errors:
- EDEADLK for arbitration lost error
- ENODATA for no answer error
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add support for at91 reset controller's basic assert/deassert
operations. Since this driver conflicts with the
SYSRESET driver because they both bind to the same RSTC node,
implement a custom bind hook that would manually bind the
sysreset driver, if enabled, to the same RSTC DT node.
Furthermore, delete the no longer needed compatibles from the
SYSRESET driver and rename it to make sure than any possible
conflicts are avoided.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Tested-by: Mihai Sain <mihai.sain@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add dm_serial driver source code for S5P4418 SOC. Extend the "arm,pl011"
driver by init of UART-clock and UART-reset.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Add the CONFIG_SYS_NAND_SELF_INIT to the Kconfig to follow the changes from
mainline.
Signed-off-by: Lokanathan, Raaj <raaj.lokanathan@intel.com>
Signed-off-by: Jit Loon Lim <jit.loon.lim@intel.com>
U-Boot serial code already handles -EAGAIN value from getc and putc
callbacks. So change drivers code to return -EAGAIN when HW is busy instead
of doing its own busy loop and waiting until HW is ready.
Signed-off-by: Pali Rohár <pali@kernel.org>
serial-uclass.c code already puts \r before \n for all dm_serial drivers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Support Holtek HT1380/HT1381 Serial Timekeeper Chip. It provides seconds
, minutes, hours, day of the week, date, month and year information.
Datasheet:
https://www.holtek.com.tw/documents/10179/11842/ht1380_1v130.pdf
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PXs3 Ref boards need to change the strength of ethernet ports
for stability, like LD20's one.
This adds the table data and fixes the boot issue on PXs3 Ref board.
Fixes: 0852033309 ("ARM: uniphier: sync with Linux 5.8-rc4")
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
The pinctrl datas of uniphier SoCs are the minimal subsets of kernel's one,
and some tables has no data to save the footprint size.
If the board dts tries to match a pin name on no pins defined SoC,
the footprint magic code causes "Synchronous Abort".
This checks if the 'pins' data is valid,
and if empty, avoids the abort with the warning as follows:
WARNING at drivers/pinctrl/uniphier/pinctrl-uniphier-core.c:36/uniphier_pinctrl_get_pins_count()!
pinctrl_select_state_full: pinctrl_config_one: err=-38
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
We've noticed that at least one Kirkwood board (Pogo v4) has problems
with the new orion DM timer implementation. Debugging revealed that this
issue is related with the static variable "early_init_done" which does
not work correctly before relocation in all cases.
This patch removes this static variable and replaces it's functionality
via a function that detects if the timer is already initialized.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pali Rohár <pali@kernel.org>
Cc: Michael Walle <michael@walle.cc>
Cc: Tony Dinh <mibodhi@gmail.com>
Tested-by: Tony Dinh <mibodhi@gmail.com>
As discussed previously [1,2], the source command is not safe to use with
verified boot unless there is a key with required = "images" (which has its
own problems). This is because if such a key is absent, signatures are
verified but not required. It is assumed that configuration nodes will
provide the signature. Because the source command does not use
configurations to determine the image to source, effectively no
verification takes place.
To address this, allow specifying configuration nodes. We use the same
syntax as the bootm command (helpfully provided for us by fit_parse_conf).
By default, we first try the default config and then the default image. To
force using a config, # must be present in the command (e.g. `source
$loadaddr#my-conf`). For convenience, the config may be omitted, just like
the address may be (e.g. `source \#`). This also works for images
(`source :` behaves exactly like `source` currently does).
[1] https://lore.kernel.org/u-boot/7d711133-d513-5bcb-52f2-a9dbaa9eeded@prevas.dk/
[2] https://lore.kernel.org/u-boot/042dcb34-f85f-351e-1b0e-513f89005fdd@gmail.com/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Two callers of image_source_script specify an image name. However, both
use the deprecated @ syntax, indicating that they have not been updated
in a while. If CONFIG_FIT_SIGNATURE is enabled, we will reject such
names outright. Back in commit 152576a598 ("stm32mp: stm32prog: handle
U-Boot script in flashlayout alternate"), we even renamed one of the
nodes. Instead of hard-coding a script image name, just use the default
image.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This value is never changed by boards, so just rename it to
SPI_IDLE_VAL to fit with the rest of the code.
Signed-off-by: Tom Rini <trini@konsulko.com>
We rename the symbol CONFIG_SEND_ENABLE to just SEND_ENABLE, and remove
the second whitespace following the define.
Signed-off-by: Tom Rini <trini@konsulko.com>
