* 'master' of git://git.denx.de/u-boot-i2c:
km/common: remove printfs for i2c deblocking code
CONFIG: SMDK5250: I2C: Enable I2C
I2C: Add support for Multi channel
I2C: Modify the I2C driver for EXYNOS5
I2C: Move struct s3c24x0_i2c to a common place.
EXYNOS: PINMUX: Add pinmux support for I2C
EXYNOS5: define EXYNOS5_I2C_SPACING
EXYNOS: Add I2C base address.
EXYNOS: CLK: Add i2c clock
mx6qsabrelite: add i2c multi-bus support
imx-common: add i2c.c for bus recovery support
i.mx53: add definition for I2C3_BASE_ADDR
i.mx: iomux-v3.c: move to imx-common directory
i.mx: iomux-v3.h: move to imx-common include directory
iomux-v3: remove include of mx6x_pins.h
mxc_i2c: finish adding CONFIG_I2C_MULTI_BUS support
mxc_i2c: add bus recovery support
mxc_i2c: prep work for multiple busses support
mxc_i2c: add i2c_regs argument to i2c_imx_stop
mxc_i2c: add retries
mxc_i2c: check for arbitration lost
mxc_i2c: change slave addr if conflicts with destination.
mxc_i2c: don't disable controller after every transaction
mxc_i2c: place i2c_reset code inline
mxc_i2c: place imx_start code inline
mxc_i2c: remove redundant read
mxc_i2c: combine i2c_imx_bus_busy and i2c_imx_trx_complete into wait_for_sr_state
mxc_i2c.c: code i2c_probe as a 0 length i2c_write
mxc_i2c: call i2c_imx_stop on error in i2c_read/i2c_write
mxc_i2c: create i2c_init_transfer
mxc_i2c: clear i2sr before waiting for bit
mxc_i2c: create tx_byte function
mxc_i2c: remove ifdef of CONFIG_HARD_I2C
mxc_i2c: fix i2c_imx_stop
i2c: deblock i2c bus also if accessed before realocation
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-microblaze:
microblaze: Wire up SPI driver
spi: microblaze: Adds driver for Xilinx SPI controller
microblaze: intc: Clear interrupt code
microblaze: Call serial multi initialization
microblaze: Move __udelay implementation
microblaze: Remove extern from board.c
microblaze: Wire up dts configuration
fdt: Add board specific dts inclusion
microblaze: Move individual board linker scripts to common script in cpu tree.
microblaze: Add gpio.h
microblaze: Add missing undefs for UBI and UBIFS
microblaze: Expand and correct configuration comments
microblaze: Enable ubi support
microblaze: Avoid compile error on systems without cfi flash
microblaze: Remove wrong define CONFIG_SYS_FLASH_PROTECTION
Conflicts:
drivers/spi/Makefile
Signed-off-by: Wolfgang Denk <wd@denx.de>
This enables I2C support on smdk5250.
Pinmux setting moved to board file to avoid repeated setting of
gpio lines.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Depending on XILINX_SPI_FLASH_BASEADDR enable SPI flash
and environment in SPI flash.
Expected values from xparameters.h are:
- XILINX_SPI_FLASH_BASEADDR
- XILINX_SPI_FLASH_MAX_FREQ
- XILINX_SPI_FLASH_CS
Signed-off-by: Stephan Linz <linz@li-pro.net>
Acked-by: Michal Simek <monstr@monstr.eu>
* 'next' of git://git.denx.de/u-boot:
MPC8xx: Fixup warning in arch/powerpc/cpu/mpc8xx/cpu.c
doc: cleanup - move board READMEs into respective board directories
net: sh_eth: add support for SH7757's GETHER
net: sh_eth: modify the definitions of regsiter
net: sh_eth: add SH_ETH_TYPE_ condition
net: sh_eth: clean up for the SH7757's code
net: fec_mxc: Fix MDC for xMII
net: fec_mxc: Fix setting of RCR for xMII
net: nfs: make NFS_TIMEOUT configurable
net: Inline the new eth_setenv_enetaddr_by_index function
net: allow setting env enetaddr from net device setting
net/designware: Consecutive writes to the same register to be avoided
CACHE: net: asix: Fix asix driver to work with data cache on
net: phy: micrel: make ksz9021 phy accessible
net: abort network initialization if the PHY driver fails
phylib: phy_startup() should return an error code on failure
net: tftp: fix type of block arg to store_block
Signed-off-by: Wolfgang Denk <wd@denx.de>
Hawkboard was using the wrong nand_read_page version for SPL image.
As a side effect, the u-boot image loaded by the SPL from nand
was getting corrupted.
Enable CONFIG_SYS_NAND_HW_ECC_OOBFIRST to select the correct nand_read_page
algorithm for SPL.
Signed-off-by: Linu Cherian <linucherian@gmail.com>
Acked-by: Sughosh Ganu <urwithsughosh@gmail.com>
Acked-by: Tom Rini <trini@ti.com>
* 'next' of git://git.denx.de/u-boot-net:
net: Inline the new eth_setenv_enetaddr_by_index function
net: allow setting env enetaddr from net device setting
net/designware: Consecutive writes to the same register to be avoided
CACHE: net: asix: Fix asix driver to work with data cache on
net: phy: micrel: make ksz9021 phy accessible
net: abort network initialization if the PHY driver fails
phylib: phy_startup() should return an error code on failure
net: tftp: fix type of block arg to store_block
Signed-off-by: Wolfgang Denk <wd@denx.de>
Micrel accidentally used the same part number
for the KS8721 and KSZ9021. So, both cannot be
in the same build of u-boot. Add a config option
to handle this.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Add I2C support.
Tested by placing a 24LC16 EEPROM into the U50 slot which comes empty from factory.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
The following platforms had their config files changed
flea3, imx31_phycore, mx35pdk, mx53ard, mx53evk, mx53smd
and mx53loco.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Clear and prepare for device-tree driven configuration.
Remove CONFIG_SYS_INTC_0 definition
Use dynamic allocation instead of static.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Simon Glass <sjg@chromium.org>
- enable OF control and embedded OF
- set default device tree file name to 'microblaze'
- add CPP to dtc proxy: board/xilinx/dts/microblaze.dts
- add an empty but processable dts for microblaze-generic
Signed-off-by: Stephan Linz <linz@li-pro.net>
* 'master' of git://git.denx.de/u-boot-arm:
tegra: define fdt_load/fdt_high variables
tegra: enable bootz command
tegra: usb: Fix device enumeration problem of USB1
tegra: trimslice: set up serial flash pinmux
tegra: add pin_mux_spi() board initialization function
tegra: add GMC/GMD funcmux entry for SFLASH
tegra: bootcmd: start USB only when needed
tegra: bootcmd enhancements
tegra: add enterrcm command
tegra: enable CONFIG_ENV_VARS_UBOOT_CONFIG
Add env vars describing U-Boot target board
tegra: usb: fix wrong error check
tegra: add ULPI on USB2 funcmux entry
tegra: fix leftover CONFIG_TEGRA2_MMC & _SPI build switches
tegra: Add Tamonten Evaluation Carrier support
tegra: Use SD write-protect GPIO on Tamonten
tegra: Implement gpio_early_init() on Tamonten
tegra: Allow boards to perform early GPIO setup
tegra: plutux: Add device tree support
tegra: medcom: Add device tree support
tegra: Rework Tamonten support
beagle: add eeprom expansion board info for bct brettl4
Signed-off-by: Wolfgang Denk <wd@denx.de>
These variables act like loadaddr, but for a device tree image. Defining
them in the environment allows boot scripts to be identical on Tegra20 and
Tegra30, which have different memory base addresses, and hence need
different values for these variables.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
bootz is just like bootm, except that it can boot a raw zImage, without
requiring it to be wrapped inside a uImage.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Instead of initializing USB as soon as bootcmd is executed, defer it
until the first boot device that (potentially in the case of network)
uses USB is scanned. This avoids initializing USB when booting from MMC,
so speeds that up.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Place the list of searched boot devices, file-system types, boot file
locations/prefixes, and boot script names into variables. This allows
the user to override them directly (e.g. to change boot order, or select
the specific values they use) without having to edit the main bootcmd
and script_boot variables.
The default boot order is changed from USB, MMC, DHCP to MMC, USB, DHCP.
This speeds up the typical MMC boot case. People who want USB boot can
now edit variable boot_targets appropriately.
Also, reformat BOOTCMDS_COMMON to fit within 80 columns.
Potential future enhancements might be:
* Allow boards to specify which of bootcmd_mmc0/... should be defined,
based on the HW they contain.
* Allow boards to influence the order that the boot targets are added
into the boot_targets variable.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra's boot ROM supports a mode whereby code may be downloaded and flash
programmed over a USB connection. On dev boards, this is typically entered
by holding down a "force recovery" button and resetting the CPU. However,
not all boards have such a button (one example is the Compulab Trimslice),
so a method to enter RCM from software is useful.
This change implements the command "enterrcm" to do this, and enables it
for all Tegra boards by default. Even on boards other than Trimslice,
controlling this over a UART may be useful, e.g. to allow simple remote
control without the need for mechanical button actuators, or hooking up
relays/... to the button.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
So that all Tegra boards define environment variables that describe
themselves.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Device tree support is required for working USB host support, which in
turn enables ethernet support.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Device tree support is required for working USB host support, which in
turn enables ethernet support.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
- fix CONFIG_SYS_MALLOC_BASE from 0x11FB_F000 to 0x13EF_F000
- add new size calculation for CONFIG_SYS_MONITOR_LEN
and CONFIG_SYS_MALLOC_LEN derived from SIZE
- change CONFIG_SYS_MONITOR_BASE and CONFIG_SYS_MALLOC_BASE
calculation to a symbolic equation with the corresponding
_LEN definitions
- add a "CFI flash memory layout - Example" comment
Signed-off-by: Stephan Linz <linz@li-pro.net>
* 'master' of git://git.denx.de/u-boot-arm: (212 commits)
ARM: cache: Move the cp15 CR register read before flushing the cache.
ARM: introduce arch_early_init_r()
PXA: Enable CONFIG_PREBOOT on zipitz2
ARM: mx28: Remove CONFIG_ARCH_CPU_INIT
No need to define CONFIG_ARCH_CPU_INIT.
add new board vl_ma2sc
MTD: SPEAr SMI: Add write support for length < 4 bytes
i2c: designware_i2c.c: Add support for the "i2c probe" command
rtc/m41t62: Add support for M41T82 with HT (Halt Update)
SPL: ARM: spear: Add SPL support for SPEAr600 platform
Makefile: Add u-boot.spr build target (SPEAr)
SPL: ARM: spear: Remove some objects from SPL build
SPL: lib/Makefile: Add crc32.c to SPL build
SPL: common/Makefile: Add image.c to SPL build
arm: Don't use printf() in SPL builds
GPIO: Add SPEAr GPIO driver
net: Multiple updates/enhancements to designware.c
cleanup/SPEAr: Define configuration flags more elegantly
cleanup/SPEAr: Remove unnecessary parenthesis
SPEAr: Correct SoC ID offset in misc configuration space
SPEAr: explicitly select clk src for UART
SPEAr: Remove CONFIG_MTD_NAND_VERIFY_WRITE to speed up NAND access
SPEAr: Enable ONFI nand flash detection for spear3xx and 6xx and evb
SPEAr: Enable CONFIG_SYS_FLASH_EMPTY_INFO macro
SPEAr: Correct the definition of CONFIG_SYS_MONITOR_BASE
SPEAr: Enable CONFIG_SYS_FLASH_PROTECTION
SPEAr: Enable dcache for fast file transfer
SPEAr: Enable autoneg for ethernet
SPEAr: Enable udc and usb-console support only for usbtty configuration
SPEAr: Enable usb device high speed support
SPEAr: Initialize SNOR in early_board_init_f
SPEAr: Change the default environment variables
SPEAr: Remove unused flag (CONFIG_SYS_HZ_CLOCK)
SPEAr: Add configuration options for spear3xx and spear6xx boards
SPEAr: Add basic arch related support for SPEAr SoCs
SPEAr: Add interface information in initialization
SPEAr: Add macb driver support for spear310 and spear320
SPEAr: Configure network support for spear SoCs
SPEAr: Place ethaddr write and read within CONFIG_CMD_NET
SPEAr: Eliminate dependency on Xloader table
SPEAr: Fix ARM relocation support
st_smi: Fixed page size for Winbond W25Q128FV flash
st_smi: Change timeout loop implementation
st_smi: Fix bug in flash_print_info()
st_smi: Change the flash probing method
st_smi: Removed no needed dependency on ST_M25Pxx_ID
st_smi: Fix smi read status
st_smi: Move status register read before modifying ctrl register
st_smi: Read status until timeout happens
st_smi: Enhance the error handling
st_smi: Change SMI timeout values
st_smi: Return error in case TFF is not set
st_smi: Add support for SPEAr SMI driver
mtd/NAND: Remove obsolete SPEAr specific NAND drivers
SPEAr: Configure FSMC driver for NAND interface
mtd/NAND: Add FSMC driver support
arm/km: remove calls to kw_gpio_* in board_early_init_f
arm/km: add implementation for read_dip_switch
arm/km: support the 2 PCIe fpga resets
arm/km: skip FPGA config when already configured
arm/km: redefine piggy 4 reg names to avoid conflicts
arm/km: cleanup km_kirkwood boards
arm/km: enable BOCO2 FPGA download support
arm/km: remove portl2.h and use km_kirkwood instead
arm/km: convert mgcoge3un target to km_kirkwood
arm/km: add kmcoge5un board support
arm/km: add kmnusa board support
arm: bugfix: save_boot_params_default accesses uninitalized stack when -O0
cm-t35: fix incorrect NAND_ECC layout selection
ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls.
ARM: OMAP4/5: Move USB pads to essential list.
ARM: OMAP4/5: Move USB clocks to essential group.
ARM: OMAP4/5: Move gpmc clocks to essential group.
ARM: OMAP4+: Move external phy initialisations to arch specific place.
omap4: Use a smaller M,N couple for IVA DPLL
da850/omap-l138: Enable auto negotiation in RMII mode
omap: am33xx: accomodate input clocks other than 24 Mhz
omap: emif: fix bug in manufacturer code test
omap: emif: deal with rams that return duplicate mr data on all byte lanes
OMAP4+: Force DDR in self-refresh after warm reset
OMAP4+: Handle sdram init after warm reset
ARM: OMAP3+: Detect reset type
arm: bugfix: Move vector table before jumping relocated code
Kirkwood: Add support for Ka-Ro TK71
arm/km: use spi claim bus to switch between SPI and NAND
arm/kirkwood: protect the ENV_SPI #defines
ARM: don't probe PHY address for LaCie boards
lacie_kw: fix CONFIG_SYS_KWD_CONFIG for inetspace_v2
lacie_kw: fix SDRAM banks number for net2big_v2
Kirkwood: add lschlv2 and lsxhl board support
net: add helper to generate random mac address
net: use common rand()/srand() functions
lib: add rand() function
kwboot: boot kirkwood SoCs over a serial link
kw_spi: add weak functions board_spi_claim/release_bus
kw_spi: support spi_claim/release_bus functions
kw_spi: backup and reset the MPP of the chosen CS pin
kirkwood: fix calls to kirkwood_mpp_conf
kirkwood: add save functionality kirkwood_mpp_conf function
km_arm: use filesize for erase in update command
arm/km: enable mii cmd
arm/km: remove CONFIG_RESET_PHY_R
arm/km: change maintainer for mgcoge3un
arm/km: fix wrong comment in SDRAM config for mgcoge3un
arm/km: use ARRAY_SIZE macro
arm/km: rename CONFIG option CONFIG_KM_DEF_ENV_UPDATE
arm/km: add piggy mac adress offset for mgcoge3un
arm/km: add board type to boards.cfg
AT91SAM9*: Change kernel address in dataflash to match u-boot's size
ATMEL/PIO: Enable new feature of PIO on Atmel device
ehci-atmel: fix compiler warning
AT91: at91sam9m10g45ek : Enable EHCI instead OHCI
Atmel : usb : add EHCI driver for Atmel SoC
Fix: AT91SAM9263 nor flash usage
Fix: broken boot message at serial line on AT91SAM9263-EK board
i.MX6 USDHC: Use the ESDHC clock
mx28evk: Fix boot by adjusting HW_DRAM_CTL29 register
i.MX28: Add function to adjust memory parameters
mx28evk: Fix PSWITCH key position
mx53smd: Remove CONFIG_SYS_I2C_SLAVE definition
mx53loco: Remove CONFIG_SYS_I2C_SLAVE definition
mx53evk: Remove CONFIG_SYS_I2C_SLAVE definition
mx53ard: Remove CONFIG_SYS_I2C_SLAVE definition
mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition
imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition
mx53ard: Remove unused CONFIG_MII_GASKET
mx6: Avoid writing to read-only bits in imximage.cfg
m28evk: use same notation to alloc the 128kB stack
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/mpc85xx: Fix Handling the lack of L2 cache on P2040/P2040E
powerpc/mpc85xx: Workaround for erratum CPU_A011
powerpc/mpc85xx: Ignore E bit for SVR_SOC_VER()
powerpc/P4080: Check SVR for CPU22 workaround
lib/powerpc: addrmap_phys_to_virt() should return a pointer
powerpc/85xx: clean up P1022DS board configuration header file
powerpc/85xx: fdt_set_phy_handle() should return an error code
powerpc/85xx: minor clean-ups to the P2020DS board header file
powerpc/p1010rdb: add readme document for p1010rdb
powerpc/mpc85xx:NAND_SPL:Avoid IFC/eLBC Base address setting
powerpc/mpc85xx:Add debugger support for e500v2 SoC
powerpc/85xx:Fix NAND code base to support debugger
powerpc/85xx:Make debug exception vector accessible
powerpc/85xx:Fix MSR[DE] bit in MSR to support debugger
PATCH 1/4][v4] doc:Add documentation for e500 external debugger support
powerpc/p1010rdb: update mux config of p1010rdb board
powerpc/mpc85xx:Add BSC9131 RDB Support
powerpc/mpc85xx:Add BSC9131/BSC9130/BSC9231 Processor Support
powerpc/85xx: Add USB device-tree fixup for various platforms
Signed-off-by: Wolfgang Denk <wd@denx.de>
No need to define CONFIG_ARCH_CPU_INIT.
All mx28 based boards should use arch_cpu_init().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
* add support for board VL+MA2SC
* adds vl_ma2sc_config for standard NOR boot configuration
* adds vl_ma2sc_ram_config for RAM load configuration
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
This patch adds the following changes to designware ethernet driver
found on the ST SPEAr SoC:
- Don't init MAC & PHY upon startup. This causes a delay, waiting for
the auto negotiation to complete. And we don't want this delay to
always happen. Especially not on platforms where ethernet is not
used at all (e.g. booting via flash).
Instead postpone the MAC / PHY configuration to the stage, where
ethernet is first used.
- Add possibility for board specific PHY init code. This is needed
for example on the X600 board, where the Vitesse PHY needs to be
configured for GMII mode.
This board specific PHY init is done via the function
designware_board_phy_init(). And this driver now adds a weak default
which can be overridden by board code.
- Use common functions miiphy_speed() & miiphy_duplex() to read
link status from PHY.
- Print status and progress of auto negotiation.
- Print link status (speed, dupex) upon first usage.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@gmail.com>
In SPEAr, some of the configuration flags eg. CONFIG_SPEAR_EMI, were given value
"1", which isn't required. Define the flags without assigning any value
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
In SPEAr configuration files, unnecessary paranthesis are used in some
\#defines. Remove them as they serve no purpose
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
When CONFIG_MTD_NAND_VERIFY_WRITE is defined, nand driver read back the data
everytime it writes. This process unnecessarily slows down the nand access.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable CONFIG_SYS_FLASH_EMPTY_INFO macro to enable reporting of empty sector
information through flinfo command.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The below text is copy pasted from README
- CONFIG_SYS_MONITOR_BASE:
Physical start address of boot monitor code (set by
make config files to be same as the text base address
(TEXT_BASE) used when linking) - same as
CONFIG_SYS_FLASH_BASE when booting from flash.
This patch corrects the definition of CONFIG_SYS_MONITOR_BASE and sets it to
TEXT_BASE
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables flash protection(lock/unlock) for CFI devices.
This is necessary because the Parallel NOR flash connected on the spear
boards, M28W64, can be locked/unlocked on a sector basis. Moreover, all its
sectors are in locked state at reset and these have to be unlocked explicitly
before being erased or written.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enabling autoneg avoids situation on few phys with fixed configuration. For
example, in one situation, nfs boot timed out when phy configuration is 100Mbps.
In another situtation, when traffic is directed to SPEAr, either thru
cross-cable or thru switch, the TFTP or DHCP command in u-boot starts to timeout
very often.
When Autoneg is ON, same phys started working perfectly.
Reported-by: Deepak Sikri <deepak.sikri@st.com>
Reported-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the UDC and usb-console support only for usbtty
configurations
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the support for usb high speed device for spear platform SOCs
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
flash reading is required earlier than flash_init is called since the env_init
is called before flash_init. This makes the smi_init necessary before env_init
being called.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch modifies the default environment variables as:
1. Default bootargs:
- console=ttyAMA0,115200
- For environment present in NOR flash
root=/dev/mtdblock3
- For environment present in NAND flash
root=/dev/mtdblock7
- Removes "mem=" option
2. Introduces CONFIG_EXTRA_ENV_USBTTY as default usbtty env var even when usbtty
is not selected
3. Add default definitions for nfsboot and ramboot
4. Add a new default environment variable(CONFIG_EXTRA_ENV_UNLOCK) for SPEAr310
and SPEAr320
Signifacance of CONFIG_EXTRA_ENV_USBTTY:
This environment variable is important for flashing utility to work. So if
somebody accidently erases the env sector then also this variable must be
preserved so that flashing utility functions properly.
Signifacance of CONFIG_EXTRA_ENV_UNLOCK:
This env variable is read by the cfi driver to unlock all flash sectors. This
is necessary because the Parallel NOR flash connected on the spear310 and
spear320 boards, M28W64, has all its sectors in locked state at reset and these
have to be unlocked explicitly before being erased or written.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
SPEAr doesn't need CONFIG_SYS_HZ_CLOCK. This commit removes it.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds options for all the below mentioned configurations and
subsequently renames the include/configs/spearxxx.h files to spear3xx_evb.h,
spear6xx_evb.h etc to depict evaluation board configuration.
SPEAr3xx and SPEAr6xx boards can be compiled in following configurations
1. Environment placed in NAND
2. Console on usb device
3. Console on usb device with environment placed in NAND
4. SPEAr310 and SPEAr320 support environment variables in parallel
NOR flash.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Earlier, architecture specific init code was mixed with board initialization
code in board/spear/... This patch updates architecture support for SPEAr in
latest u-boot and prints the SoC information.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
SPEAr310 and SPEAr320 SoCs have an extra ethernet controller. The
driver for this device is already supported by u-boot, so configuring
board configuration file and defining base addresses etc to make use
of the common driver
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
SMI is the serial memory interface controller provided by ST.
Earlier, a driver exists in the u-boot source code for the SMI IP. However, it
was specific to spear platforms. This commit converts the same driver to a more
generic driver. As a result, the driver files are renamed to st_smi.c and
st_smi.h and moved into drivers/mtd folder for reusability by other platforms
using smi controller peripheral.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Since FSMC is a standard IP and it supports different memory interfaces, it
is supported independent of spear platform and spear is configured to use that
driver for interfacing with the NAND device
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
These functions tried to access two static tables before relocation
(board_early_init_f is executed before relocation). But these static
tables lie in the bss section which is not valid before relocation.
These accesses then overwrote some parts of u-boot binary before it was
relocated. For the kmnusa build, this results in a corrupted important
env variable (bootcmd) but it may be that some other parts of the u-boot
binary are corrupted.
This patch solves this problem by moving all the kw_gpio_* calls to
board_init, which should be early enough in the boot sequence. The only
calls that could not be moved is the one for the SOFT (bitbang) I2C, and
they have been replaced by a direct access to the GPIO dataout Control
register to set the two GPIOs as output.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Add a function to read the dip_switch on kmcoge5un. If the
switch is set the actual_bank is set to 0 and this SW is
booted.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Remove config options from boards.cfg and simply add one switch
per board and differ afterwards in km_kirkwood.h between the features.
More boards are upcoming and therefore it's easier to have this
at one place.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This adds a first support of the FPGA download for a PCIe FPGA based
on the BOCO2 CPLD.
This takes place in 3 steps, all done accessing the SPICTRL reg of the
BOCO2:
1) start the FPGA config with an access to the FPGA_PROG bit
2) later in the boot sequence, wait for the FPGA_DONE bit to toggle to 1
for the end of the FPGA configuration (with a timeout)
3) reset the FPGA
4) finally remove the access to its config EEPROM from the FPGA so that
the CPU can update the FPGA configuration when the kernel is running
The boards with a PCIe FPGA but without BOCO2 still are supported.
The config option name is CONFIG_KM_FPGA_CONFIG
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
The additional headerfile is unneeded here, we can use the generic
km_kirkwood.h instead. And we can use the better config option
KM_PIGGY4_88E6061 for the specific features for boards with this
design in km_arm.c.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Use the generic header km_kirkwood.h and get rid of the
board specific header.
changes for v2: rebased because of changes in other patches
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
For u-boot this board is similar to mgcoge3un. But some differences
are present. We have a different SDRAM on it and therefore a new
SDRAM config file. Additionaly this board has a direct MAC/MAC
connection from the kirkwood to a marvell simple switch without a
phy inbetween, this needs a new configuration for the mvgbe driver.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This board is similar to portl2, but it has the u-boot environment
in a SPI NOR flash and not in an i2c eeprom like portl2 have.
Some other details:
- IVM EEPROM is at adress: pca9547:70:9
- PCI is enabled
- PIGGY4 is connected via MV88E6352 simple switch. There is no phy
between the simple switch and the kirkwood.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
The current configuration selects an incorrect NAND ECC layout,
which causes u-boot to write HW ECC data incorrectly.
This patch selects the right layout.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Currently on OMAP4/5 platforms, many kernel drivers are dependent
upon the bootloaders for mux, dpll and clock configurations.
This should not be the case and bootloaders should set only the
minimum required for the uboot functionality and kernel boot.
Note that this is going to break the kernel drivers. But this
is the only way to get things fixed in the kernel.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
We overwrite these weak functions from the kirkwood spi code to
use our own method to be able to switch between the SPI NOR and
the NAND flash. This is needed e.g. to update the u-boot. The former
command do_spi_toggle can therefore be removed. And the usage of
this command is removed from the u-boot update command in the
u-boot environment.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This patch adds support for both the Linkstation Live (LS-CHLv2) and
Linkstation Pro (LS-XHL) by Buffalo.
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
We used to have an arbitrary value, which can be a problem if we have a
u-boot image that is bigger than this value.
This patch is dependant on the whole km/arm series and will be included
in the v3 of the series if there is one.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This is already defined in the generic kirkwood header.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This config option sounds like the it is responsible for the
update of the environment, but it is the u-boot update handling.
Therefore we adapt it to a more apropriate naming.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Some other kirkwood boards from keymile will follow. They will have some
small differences, but we want to use the km_kirkwood.h for all to
distinguish them. This patch a preparation for this.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
On at91sam platforms, u-boot grew larger than the allocated size in
dataflash, the layout was:
bootstrap 0x00000000
ubootenv 0x00004200
uboot 0x00008400
kernel 0x00042000
fs 0x00252000
u-boot with the defconfig doesn't seem to fit in 0x42000 - 0x8400 =
0x39C00 bytes anymore.
Now, the layout is:
bootstrap 0x00000000
ubootenv 0x00004200
uboot 0x00008400
kernel 0x00084000
fs 0x00294000
Signed-off-by: Alexandre Belloni <alexandre.belloni@piout.net>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
According to include/i2c.h:
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
According to include/i2c.h:
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
According to include/i2c.h:
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
According to include/i2c.h:
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
According to include/i2c.h:
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
According to include/i2c.h:
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Original code was assuming that the fuse revision version for all mx53loco boards
based on Dialog PMIC was the same, which is not the case.
Force the revision of all Dialog-based boards to 0.
This fixes a kernel crash when PMIC is accessed in the 2.6.35 kernel
for Dialog rev E boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reduce the environment size (128KB => 16KB) to improve the environment
operations time (e.g. reading, ecc calculation).
Also, remove the unused CONFIG_SYS_ENV_SECT_SIZE.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
We reduce the bootdelay from 10s to 3s to give users a short but usable
window to interrupt the boot process if needed.
Signed-off-by: Tom Rini <trini@ti.com>
- change gpio pin settings:
- gpio pin 6[13] (PLC reset) default value low
- gpio pin 6[0] (TPM reset) default value low
- 4 new GPIO pins
pin i/o name
- 3[9] input Board Type
- 2[7] input HW-ID0
- 2[6] input HW-ID1
- 2[3] input HW-ID2
- read board type and hw id from gpio pins on the enbw_cmc board,
and use board type for setting up different gpio pin settings.
- do not pass "davinci_mmc.use_dma=0" to linux, as MMC now
works with DMA.
- update logbuf support:
store post word in RTC scratch register
- add support for configuring KSZ8864RMN switch through
a config file on u-boot startup. For more infos see:
doc/README.switch_config
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Fix the .dts file USB unit addresses not to duplicate each-other.
Fix the board name string to indicate the vendor is Compulab not NVIDIA.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Walk the BIT and BCT to find the ODMDATA word in the
CustomerData field and put it into Scratch20 reg for
use by kernel, etc.
Built all Tegra builds OK; Booted on Seaboard and saw
ODMDATA in PMC scratch20 was the same as the value in my
burn-u-boot.sh file (0x300D8011). NOTE: All flash utilities
will have to specify the odmdata (nvflash --odmdata n) on
the command line or via a cfg file, or built in to their
BCT.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
The SPI hardware on Seaboard is too broken to use; it is muxed with the
console UART and requires evil interactions between the SPI and UART
drivers to work even partially. The current code in U-Boot is not
sufficient to make this work correctly; auto boot is aborted due to
corruption in the UART RX channel interrupting it.
Instead, move the environment to eMMC, at the end of the second boot
sector. This should not conflict with any other eMMC usage, irrespective
of whether the board boots from SPI, NAND, or eMMC: if U-Boot is stored
in eMMC, it will be stored well below this location. The kernel only
uses the general area of the eMMC once booted, not the boot sectors.
Boards that are derivatives of Seaboard don't have the muxing issue,
and should/could have a separate U-Boot configuration file that does
enable SPI if desired.
Alternatively, the environment could be stored in NAND flash, but we
currently have no driver for that controller.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Store the environment in eMMC, at the end of the second boot sector.
This should not conflict with any other eMMC usage: U-Boot is stored
well below this location, and the kernel only uses the general area
of the eMMC once booted, not the boot sectors.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In anticipation of Tegra3 support, continue removing/renaming
Tegra2-specific files. No functional changes (yet).
Updated copyrights to 2012.
Signed-off-by: Tom Warren <twarren@nvidia.com>
In anticipation of Tegra3 support, continue removing/renaming
Tegra2-specific files. No functional changes (yet).
Updated copyrights to 2012.
Signed-off-by: Tom Warren <twarren@nvidia.com>
In anticipation of Tegra3 support, start removing/renaming
Tegra2-specific files. No functional changes (yet).
Also updated copyright to 2012.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Store the environment in eMMC, at the end of the second boot sector.
This should not conflict with any other eMMC usage: U-Boot is stored
well below this location, and the kernel only uses the general area
of the eMMC once booted, not the boot sectors.
Note: This assumes the user plugged the standard 8MB MoviNAND card into
J29/HSMMC/POP. If they didn't, the boot sector layout may be different.
However, use of that particular card is standard practice as far as I
know.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Store the environment in eMMC, at the end of the second boot sector.
This should not conflict with any other eMMC usage: U-Boot is stored
well below this location, and the kernel only uses the general area
of the eMMC once booted, not the boot sectors.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a device tree for Ventana; the Seaboard file no longer represents
the HW present on Ventana.
Enable USB on Ventana.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The SMSC95xx series may exist either directly on a main board, or as a USB
to Ethernet dongle. However, dongles containing these chips are very rare.
Hence, remove this config option, except on Harmony where such a chip is
actually present on the board.
The asix option remains, since it's a popular chip, and I actively use a
dongle containing this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
... to enable USB host support, which enables Ethernet support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
... to enable USB host support, which enables Ethernet support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
CONFIG_CMD_PING/NFS aren't required for Whistler to boot.
Add some comments.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This implements a useful bootcmd for Tegra. The boot order is:
* If USB enabled, USB storage
* Internal MMC (SD card or eMMC)
* If networking is enabled, BOOTP/TFTP
When booting from USB or MMC, the boot script is assumed to be in
partition 1 (although this may be overridden via the rootpart variable),
both ext2 and FAT filesystems are supported, the boot script may exist
in either / or /boot, and the boot script may be named boot.scr.uimg or
boot.scr.
When booting over the network, it is assumed that boot.scr.uimg exists
on the TFTP server. There is less flexibility here since those setting
up network booting are expected to need less hand-holding.
In all cases, it is expected that the initial file loaded is a U-Boot
image containing a script that will load the kernel, load any required
initrd, load any required DTB, and finally bootm the kernel.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
console isn't used by anything, and the kernel should be set appropriately
by whatever script is booting the kernel, not imposed by the bootloader.
mem might be useful, but the current value is pretty bogus, since it
includes nvmem options that make no sense for an upstream kernel, and
equally should not be required for any downstream kernel. Either way, this
is also best left to the kernel boot script.
smpflag isn't used by anything, and again was probably intended to be a
kernel command-line option better set by the kernel boot script.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Whistler is a highly configurable Tegra evaluation and development board.
This change adds support for the following specific configuration:
E1120 motherboard
E1108 CPU board
E1116 PMU board
The motherboard configuration switches are set as follows:
SW1=0 SW2=0 SW3=5
S1/S2/S3/S4 all on, except S3 7/8 are off.
Other combinations of daugher boards may work to varying degrees, but will
likely require some SW adjustment.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Remove some unused default environment variables (memctl_intlv_ctl,
perf_mode, diuregs, dium, and diuerr), update 'tftpflash' variable,
and add videobootargs as a Linux command line variable (so that we can
easily pass video= to the kernel).
Signed-off-by: Timur Tabi <timur@freescale.com>
Remove some unused macros and remove all #undef macros.
The RTL8139 network adapter is not shipped with the board nor commonly
used, so don't define it by default. The E1000 is still defined.
Add 57,600 baud as an option. For some reason, this baud rate is missing
from many boards.
Signed-off-by: Timur Tabi <timur@freescale.com>
BSC9131RDB is a Freescale reference design board for BSC9131 SoC. BSC9131 SOC
is an integrated device that targets Femto base station market. It combines
Power Architecture e500v2 and DSP StarCore SC3850 core technologies with
MAPLE-B2F baseband acceleration processing elements
BSC9131RDB Overview
-----------------
-1Gbyte DDR3 (on board DDR)
-128Mbyte 2K page size NAND Flash
-256 Kbit M24256 I2C EEPROM
-128 Mbit SPI Flash memory
-USB-ULPI
-eTSEC1: Connected to RGMII PHY
-eTSEC2: Connected to RGMII PHY
-DUART interface: supports one UARTs up to 115200 bps for console display
Apart from the above it also consists various peripherals to support DSP
functionalities.
This patch adds support for mainly Power side functionalities and peripherals
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
extention of commit 3b6b256 "powerpc/mpc83xx: increment
malloc heap size for the MPC832x MDS boards" to all other
mpc83xx based boards. It fixes "Unable to save the rest
of sector" messages when trying to save the environment
to flash.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Increase malloc area for UBI to >= 512k -- foreseeing of UBIFS
set to 768k. To save memory in flash (CONFIG_SYS_MONITOR_LEN)
the UBIFS is disabled by default.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Use XILINX_FLASH_START to set/unset FLASH and RAMENV.
Error:
board.c: In function 'board_init':
board.c:134: error: 'XILINX_FLASH_START' undeclared (first use in this function)
board.c:134: error: (Each undeclared identifier is reported only once
board.c:134: error: for each function it appears in.)
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Michal Simek <monstr@monstr.eu>
CONFIG_SYS_FLASH_PROTECTION is defined twice. The second one
is outside the flash configuration context and we can remove
it safely.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2. I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in <config_fallbacks.h> which mkconfig places after <configs/...h> in
the generated config file. This is used when a board has not set its
own table.
Signed-off-by: Tom Rini <trini@ti.com>
If the testpin is asserted, first check if a test_bank
variable is defined before trying to boot this
test_bank.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
kmcoge5ne starts the post tests if the testpin on
the board was enabled. Currently it does simply a memory
test.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Increase bootlimit to 3 to be more tolerant during the
boot process before switching to the backup application.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This board is a MPC8360 board. Two flashes are present
a NOR flash were u-boot and the u-boot environment is stored
and a NAND flash for the application code. This board has 512MB
SDRAM.
Additionaly we introduce a common km8360.h file and convert kmeter1 to
use this.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Christian Herzig <christian.herzig@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add support for a second flash.
By default, a single flash chip is set up:
- called 'boot'
- mtd name for ubi 'ubi0'
MTDIDS and MTDPARTS may be overwritten to add a second flash.
The 'ubiattach' command is featured in two versions:
- if CONFIG_KM_UBI_PARTITION_NAME_APP is not defined:
this is the version as up to now
- if CONFIG_KM_UBI_PARTITION_NAME_APP is defined:
a check on 'actual_bank' will be done to determine the flash to boot
from.
Use CONFIG_KM_UBI_PARTITION_NAME_BOOT and
CONFIG_KM_UBI_PARTITION_NAME_APP to define where to put the bootloader
and the applications.
Example:
In the board config do:
... snip ...
"boot:" \
"768k(u-boot)," \
"128k(env)," \
"128k(envred)," \
"-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");" \
"app:" \
"-(" CONFIG_KM_UBI_PARTITION_NAME_APP ");"
... snap ...
You may also need to enable the second flash:
... snip ...
/* additional featured for COGE5 */
... snap ...
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
We don't use PCI on kmeter1 and never will be, so remove some
unneeded code.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This additional header is unneeded, we can use the tuxx1.h for this
target.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The malloc buffer is not large enough to hold a flash sector (0x20000 bytes)
in addition to whatever else it normally holds, so double its size. This
fixes a failure trying to save the environment:
=> save
Saving Environment to Flash...
Unable to save the rest of sector (122880)
. done
Protected 1 sectors
This problem probably surfaced from some other change that significantly
increased the normal memory usage, thereby not leaving enough room for
the saveenv command.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* 'master' of git://git.denx.de/u-boot-video:
video: atmel/lcd: add LCD driver for new Atmel SoC
video: cfb_console: flush dcache for frame buffer in DRAM
cfb_console: Ignore bell character
cfb_console: Add console_clear_line function
cfb_console: Fix function console_back
omap3_dss: cosmetic changes
omap3_dss: add optional framebuffer
mx53loco: Add LCD support
mx5: Rename mx51_fb_init()
mx53: Allow IPUv3 driver to also work on mx53
mx51evk: Add LCD support
EXYNOS: display 32bpp bitmap TIZEN logo
create lib/tizen directory
LCD: display 32bpp decompressed bitmap image
common/lcd.c: reduce one CONFIG_LCD_LOGO ifdef
common/lcd.c: reduce some CONFIG_LCD_*_LOGO ifdefs
common/lcd.c: use ARRAY_SIZE
cmd_bmp.c: make bmp_display() usable by drivers or board code
LCD: support another s6e8ax0 panel type
LCD: change s6e8ax0 panel gamma value
include/video.h: drop unused video_printf()
Signed-off-by: Wolfgang Denk <wd@denx.de>
This is an sh2a device (max 266MHz) with FPU, video display
controller (VDC), 8 serial ports, 4 I2C channels, 3 CAN ports,
SD and on-chip USB.
The RSK2+SH7269 board uses the SH7269 processor. It is often
referred to as just rsk7269.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The board with sh_eth needs to set CONFIG_SH_ETHER_PHY_MODE.
And SH7734 needs to set value of CONFIG_SH_ETHER_SH7734_MII.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The AP-SH4A-4A board has SH7734, 64MB DDR2-SDRAM, USB,
Ethernet, and more.
This patch supports the following functions:
- 64MB DDR2-SDRAM
- 16MB NOR Flash memory
- Serial console (SCIF)
- Ethernet (SH-Ether with Gigabit)
- I2C
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This read MAC address from Serial EEPROM and set.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The r0p7734 board has SH7734, 128MB DDR2-SDRAM, USB,
Ethernet, and more.
This patch supports the following functions:
- 128MB DDR2-SDRAM
- 32MB NOR Flash memory
- Serial console (SCIF)
- Ethernet (SH-Ether/SMSC)
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for CLAA07LC0ACW LCD that connects to the mx53loco board.
Configure the board to show the Linux logo on the LCD.
Also increase the size of CONFIG_SYS_MALLOC_LEN variable to take into account
the framebuffer usage.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Add support for CLAA07LC0ACW LCD that connects to the mx51evk board.
Configure the board to show the Linux logo on the LCD.
Also increase the size of CONFIG_SYS_MALLOC_LEN variable to take into account
the framebuffer usage.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This patch supports drawing 32bpp bitmap TIZEN logo in exynos fb.
"tizen_hd_logo.h" data is compressed from trats_logo.bmp to
trats_logo.bmp.gz by gzip and converted to tizen_hd_logo.h header file
format by some application. The logo data is decompressed in the exynos
fb driver by bmp_display().
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Some boards claim to need ping, but don't support net.
That makes no sense, and causes problems now that ping
is in a separate file.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
* 'master' of git://git.denx.de/u-boot-arm: (167 commits)
OMAP4/5: Change omap4_sdp, omap4_panda, omap5_evm maintainer
ARM: omap3: Add CONFIG_SPL_BOARD_INIT for CONFIG_SPL_MMC_SUPPORT
ARM: omap3: Set SPL stack size to 8KB, image to 54KB.
arm, omap3: fix warm reset serial output on OMAP36xx/AM/DM37xx
OMAP4: Set fdt_high for OMAP4 devices to enable booting with Device Tree
omap4: do not enable auxiliary cores
omap4: do not enable fs-usb module
omap4: panda: disable uart2 pads during boot
igep00x0: change mpurate from 500 to auto
igep00x0: enable the use of a plain text file
tegra2: trivially enable 13 mhz crystal frequency
tegra: Enable keyboard for Seaboard
tegra: Switch on console mux and use environment for console
tegra: Add tegra keyboard driver
tegra: fdt: Add keyboard definitions for Seaboard
tegra: fdt: Add keyboard controller definition
tegra: Add keyboard support to funcmux
input: Add support for keyboard matrix decoding from an fdt
input: Add generic keyboard input handler
input: Add linux/input.h for key code support
fdt: Add fdtdec functions to read byte array
tegra: Enable LP0 on Seaboard
tegra: fdt: Add EMC data for Tegra2 Seaboard
tegra: i2c: Add function to find DVC bus
fdt: tegra: Add EMC node to device tree
tegra: Add EMC settings for Seaboard
tegra: Turn off power detect in board init
tegra: Set up warmboot code on Nvidia boards
tegra: Setup PMC scratch info from ap20 setup
tegra: Add warmboot implementation
tegra: Set up PMU for Nvidia boards
tegra: Add PMU to manage power supplies
tegra: Add EMC support for optimal memory timings
tegra: Add header file for APB_MISC register
tegra: Add tegra_get_chip_type() to detect SKU
tegra: Add flow, gp_padctl, fuse, sdram headers
tegra: Add crypto library for warmboot code
tegra: Add functions to access low-level Osc/PLL details
tegra: Move ap20.h header into arch location
Add AES crypto library
i2c: Add TPS6586X driver
Add abs() macro to return absolute value
fdt: Add function to return next compatible subnode
fdt: Add function to locate an array in the device tree
i.MX28: Avoid redefining serial_put[cs]()
i.MX28: Check if WP detection is implemented at all
i.MX28: Add battery boot components to SPL
i.MX28: Reorder battery status functions in SPL
i.MX28: Add LRADC init to i.MX28 SPL
i.MX28: Add LRADC register definitions
i.MX28: Shut down the LCD controller before reset
i.MX28: Add LCDIF register definitions
i.MX28: Implement boot pads sampling and reporting
i.MX28: Improve passing of data from SPL to U-Boot
M28EVK: Add SD update command
M28EVK: Implement support for new board V2.0
FEC: Abstract out register setup
MX5: PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH exchanged
i.MX28: Add delay after CPU bypass is cleared
spi: mxs: Allow other chip selects to work
spi: mxs: Introduce spi_cs_is_valid()
mx53loco: Remove unneeded gpio_set_value()
mx53loco: Add CONFIG_REVISION_TAG
mx53loco: Turn on VUSB regulator
mx53loco: Add mc34708 support and set mx53 frequency at 1GHz
pmic: dialog: Avoid name conflicts
imx: Add u-boot.imx as target for ARM9 i.MX SOCs
i.MX2: Include asm/types.h in arch-mx25/imx-regs.h
imx: usb: There is no such register
i.MX25: usb: Set PORTSCx register
imx: nand: Support flash based BBT
i.MX25: This architecture has a GPIO4 too
i.MX25: esdhc: Add mxc_get_clock infrastructure
i.MX6: mx6q_sabrelite: add SATA bindings
i.MX6: add enable_sata_clock()
i.MX6: Add ANATOP regulator init
mx28evk: add NAND support
USB: ehci-mx6: Fix broken IO access
M28: Scan only first 512 MB of DRAM to avoid memory wraparound
Revert "i.MX28: Enable additional DRAM address bits"
M28: Enable FDT support
mx53loco: Add support for 1GHz operation for DA9053-based boards
mx53loco: Allow to print CPU information at a later stage
mx5: Add clock config interface
imx-common: Factor out get_ahb_clk()
i.MX6Q: mx6qsabrelite: Add keypress support to alter boot flow
mx31pdk: Allow booting a zImage kernel
mx6qarm2: Allow booting a zImage kernel
mx6qsabrelite: Allow booting a zImage kernel
mx28evk: Allow booting a zImage kernel
m28evk: Allow to booting a dt kernel
mx28evk: Allow to booting a dt kernel
mx6qsabrelite: No need to set the direction for GPIO3_23 again
pmic: Add support for the Dialog DA9053 PMIC
MX53: mx53loco: Add SATA support
MX53: Add support to ESG ima3 board
SATA: add driver for MX5 / MX6 SOCs
MX53: add function to set SATA clock to internal
SATA: check for return value from sata functions
MX5: Add definitions for SATA controller
NET: fec_mxc.c: Add a way to disable auto negotiation
Define UART4 and UART5 base addresses
EXYNOS: Change bits per pixel value proper for u-boot.
EXYNOS: support TRATS board display function
LCD: support S6E8AX0 amoled driver based on EXYNOS MIPI DSI
EXYNOS: support EXYNOS MIPI DSI interface driver.
EXYNOS: support EXYNOS framebuffer and FIMD display drivers.
LCD: add data structure for EXYNOS display driver
EXYNOS: add LCD and MIPI DSI clock interface.
EXYNOS: definitions of system resgister and power management registers.
SMDK5250: fix compiler warning
misc:pmic:samsung Convert TRATS target to use MAX8997 instead of MAX8998
misc:pmic:max8997 MAX8997 support for PMIC driver
TRATS: modify the trats's configuration
ARM: Exynos4: ADC: Universal_C210: Enable LDO4 power line for ADC measurement
EXYNOS: Rename exynos5_tzpc structure to exynos_tzpc
arm: ea20: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
arm: cam_enc_4xx: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
cm-t35: add I2C multi-bus support
include/configs: Remove CONFIG_SYS_64BIT_STRTOUL
include/configs: Remove CONFIG_SYS_64BIT_VSPRINTF
omap3: Introduce weak misc_init_r
omap730p2: Remove empty misc_init_r
omap5912osk: Remove empty misc_init_r
omap4+: Remove CONFIG_ARCH_CPU_INIT
omap4: Remove CONFIG_SYS_MMC_SET_DEV
OMAP3: pandora: drop console kernel argument
OMAP3: pandora: revise GPIO configuration
...
As originally reported against beagleboard we currently have the
following error message reported in SPL:
U-Boot SPL 2012.04-00020-gb8310b9-dirty (Apr 25 2012 - 18:49:57)
Texas Instruments Revision detection unimplemented
OMAP SD/MMC: 0
timed out in wait_for_bb: I2C_STAT=1000
reading u-boot.img
....
The reason for above message is that when booting from MMC, I2C needs to
be initialized to talk with the TWL4030. On OMAP3 I2C is only
initalized in SPL if CONFIG_SPL_BOARD_INIT is set.
Cc: Thomas Weber <weber@corscience.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Original patch for Beagleboard is:
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
Extended to cover all other boards:
Signed-off-by: Tom Rini <trini@ti.com>
With older toolchains it is possible to not fit entirely into the 45KB
that we had assigned to SPL. Adjust to allow for 8KB of stack (which
should be more than required) and 54KB of text/data.
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
For OMAP4 boards, such as the panda-es, that have 1GB of memory the linux
kernel fails to locate the device tree blob on boot. The reason being is that
u-boot is copying the DT blob to the upper part of RAM when booting the kernel
and the kernel is unable to access the blob. By setting the fdt_high variable
to either 0xffffffff (to prevent the copy) or 0xac000000 (704MB boundary
of memory for OMAP4) the kernel is able to locate the DT blob and boot.
Based upon following patch by Dirk Behme set the fdt_high variable to allow
booting with device tree on OMAP4 boards.
"7e9603e i.mx6q: configs: Add fdt_high and initrd_high variables"
Cc: Sricharan R <r.sricharan@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
This patch changes the default mpurate variable from 500 to auto on
all IGEP boards, with this the default rate is autoselected.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Based on commit cf073e49bc for beagleboard
Using the new env import command it is possible to use plain text files instead
of script-images. Plain text files are much easier to handle.
E.g. If your boot.scr contains the following:
-----------------------------------
setenv dvimode 1024x768-16@60
run loaduimage
run mmcboot
-----------------------------------
you could create a file named uEnv.txt and use that instead of boot.scr:
-----------------------------------
dvimode=1024x768-16@60
uenvcmd=run loaduimage; run mmcboot
-----------------------------------
The variable uenvcmd (if existent) will be executed (using run) after uEnv.txt
was loaded. If uenvcmd doesn't exist the default boot sequence will be started,
therefore you could just use
-----------------------------------
dvimode=1024x768-16@60
-----------------------------------
as uEnv.txt because loaduimage and mmcboot is part of the default boot sequence
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add "update_sd_firmware" command to easily reload the SD card of
m28evk kit. This comes handy when the board boots from SD card.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG information.
The kernel uses this data to distinguish between Dialog versus mc34708 based boards,
and also to distinguish between revA and revB of the mc34708 based boards.
Suggested-by: Yu Li <yk@magniel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add mc34708 support and set mx53 core frequency at its maximum value of 1GHz.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
NAND support is not enabled by default because Eval Kit is not delivered
with NAND chip. To enable NAND support add CONFIG_CMD_NAND to board config.
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Acked-by: Marek Vasut <marex@denx.de>
This will eventually be needed with Linux 3.5, which will be the point when
MXS will be switched to FDT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
There are two types of mx53loco boards: initial boards were built with a Dialog
DA9053 PMIC and more recent version is based on a Freescale MC34708 PMIC.
Add DA9053 PMIC support and adjust the required voltages and clocks for running
the CPU at 1GHz.
Tested on both versions of mx53loco boards.
In the case of a MC34708-based board the CPU operating voltage remains at 800MHz.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by : Stefano Babic <sbabic@denx.de>
Print CPU information within board_late_init().
This is in preparation for adding 1GHz support, which requires programming a PMIC
via I2C. As I2C is only available after relocation, print the CPU information
later at board_late_init(), so that the CPU frequency can be printed correctly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Uses the 'magic_keys' idiom as described in doc/README.kbd:
http://lists.denx.de/pipermail/u-boot/2012-April/122502.html
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Allow booting a zImage kernel.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
The ESG ima3-mx53 board is based on the Freescale
i.MX53 SOC. It boots from NOR (128 MB) and
supports Ethernet (FEC), SATA.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This patch support TRATS board configuration and display function.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Trats is supported 1GiB memory size.
(Each bank size is 512MB.)
And INITRD is unnecessary. So removed them.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
With almost all the architecture and board BOARD_LATE_INIT does not use.
CONFIG_BOARD_LATE_INIT is used instead.
This changed CONFIG_BOARD_LATE_INIT from BOARD_LATE_INIT.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
With almost all the architecture and board BOARD_LATE_INIT does not use.
CONFIG_BOARD_LATE_INIT is used instead.
This changed CONFIG_BOARD_LATE_INIT from BOARD_LATE_INIT.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Enable I2C multi-bus support and config I2C muxes for I2C2 and I2C3.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
As ttyS0 is no longer valid for newer OMAP kernels, and pandora serial
cables are not widespread, simply drop console argument. This should
allow booting old and new kernels with default arguments, and those who
need serial can use a boot script on SD card.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
This is rework on config files of IGEP-based boards with the aim to remove
duplicated code to be more maintainable. Basically this patch creates a
common configuration file for both boards and only sets the specific option
in the board config file.
On board files the hardcored mach type was replaced in favour of using the
CONFIG_MACH_TYPE option.
More than 200 duplicated lines have been deleted.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
This change adds a basic support for Embest/Timll DevKit3250 board,
NOR and UART are the only supported peripherals for a moment. The board
doesn't require low-level init, because the initial SDRAM and GPIO
configuration is performed during kickstart bootloader execution.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
To support sdhci controller, remove the CONFIG_S5P_MMC..
Instead, use the CONFIG_S5P_SDHCI/CONFIG_SDHCI.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
PowerPC: correct the SATA for p1/p2 rdb-pc platform
powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
powerpc/corenet_ds: Slave module for boot from SRIO
powerpc/corenet_ds: Master module for boot from SRIO
powerpc/corenet_ds: Document for the boot from SRIO
powerpc/corenet_ds: Correct the compilation errors about ENV
powerpc/srio: Rewrite the struct ccsr_rio
powerpc/85xx:Fix lds for nand boot debug info
powerpc/p2041rdb: add env in NAND support
powerpc/p2041rdb: add NAND and NAND boot support
powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
powerpc/85xx:Avoid vector table compilation for nand_spl
powerpc/85xx:Fix IVORs addr after vector table relocation
powerpc/85xx:Avoid hardcoded vector address for IVORs
powerpc/p1023rds: Disable nor flash node and enable nand flash node
* 'master' of git://git.denx.de/u-boot-i2c:
i2c:designware Turn off the ctrl when setting the speed
i2c: Add support for designware i2c controller
sh: i2c: Add support I2C controller of SH7734
* 'master' of git://git.denx.de/u-boot-nds32:
board/adp-ag102: add configuration of adp-ag102
board/adp-ag102: add board specific files
nds32/ag102: add ag102 soc support
nds32/ag102: add header support of ag102 soc
In hardware revision 1.20 one more fan controller is added to dlvision-10g.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Print fpga info at last_stage_init on gdsys 405ep boards.
Use dtt_init() to startup fans.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
In order to add boards that have different hardware for fpga reset,
any 405ep gdsys board now provides these functions:
void gd405ep_init(void);
void gd405ep_set_fpga_reset(unsigned state);
void gd405ep_setup_hw(void);
int gd405ep_get_fpga_done(unsigned fpga);
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Environment size on neo has to be 0x20000 for compatibilty reasons.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
* 'marex@denx.de' of git://git.denx.de/u-boot-staging:
CMD: CONFIG_CMD_SETECPR -> CONFIG_CMD_SETEXPR on omap3_logic
CMD: Fix CONFIG_CMD_SAVEBP_WRITE_SIZE -> CONFIG_CMD_SPL_WRITE_SIZE
CMD: Fix typo CMD_FSL -> CMD_MFSL in readme
HWW1U1A: Fix CMD_SHA1 -> CMD_SHA1SUM
CMD: Remove CMD_LOG, it's unused
CMD: Fix typo KGBD -> KGDB on debris board
CMD: Drop CONFIG_CMD_EMMC, it's not used
CMD: Drop CONFIG_CMD_DFL, it's not used
CMD: Drop CMD_DCR, it's not used
CMD: Drop CMD_CAN, it's not used
CMD: Remove CMD_AUTOSCRIPT, it's not used
AT91: Drop AT91_SPIMUX command from cmd_all
For p1/p2 rdb-pc platform, use the PCIe-SATA Silicon Image SATA controller.
Therefore, the SATA driver will use sata_sil, instead sata_sil3114.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Andy Fleming <afleming@gmail.com>
When boot from SRIO, slave's core can be in holdoff after powered on for
some specific requirements. Master can release the slave's core at the
right time by SRIO interface.
Master needs to:
1. Set outbound SRIO windows in order to configure slave's registers
for the core's releasing.
2. Check the SRIO port status when release slave core, if no errors,
will implement the process of the slave core's releasing.
Slave needs to:
1. Set all the cores in holdoff by RCW.
2. Be powered on before master's boot.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
When boot from SRIO, slave's ENV can be stored in master's memory space,
then slave can fetch the ENV through SRIO interface.
NOTE: Because the slave can not erase, write master's NOR flash by SRIO
interface, so it can not modify the ENV parameters stored in
master's NOR flash using "saveenv" or other commands.
Master needs to:
1. Put the slave's ENV into it's own memory space.
2. Set an inbound SRIO window covered slave's ENV stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode and ENV from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode and ENV.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
When boot from SRIO, slave's ucode can be stored in master's memory space,
then slave can fetch the ucode image through SRIO interface. For the
corenet platform, ucode is for Fman.
Master needs to:
1. Put the slave's ucode image into it's own memory space.
2. Set an inbound SRIO window covered slave's ucode stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.
The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image in master NOR flash.
3. Normally boot from local NOR flash.
4. Configure SRIO switch system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to SRIO1 or SRIO2 by RCW.
3. RCW should configure the SerDes, SRIO interfaces correctly.
4. Slave must be powered on after master's boot.
5. Must define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE because of no ucode
locally.
For the slave module, need to finish these processes:
1. Set the boot location to SRIO1 or SRIO2 by RCW.
2. Set a specific TLB entry for the boot process.
3. Set a LAW entry with the TargetID SRIO1 or SRIO2 for the boot.
4. Slave's u-boot image should be generated specifically by
make xxxx_SRIOBOOT_SLAVE_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.
The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image in master NOR flash.
3. Normally boot from local NOR flash.
4. Configure SRIO switch system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to SRIO1 or SRIO2 by RCW.
3. RCW should configure the SerDes, SRIO interfaces correctly.
4. Slave must be powered on after master's boot.
For the master module, need to finish these processes:
1. Initialize the SRIO port and address space.
2. Set inbound SRIO windows covered slave's u-boot image stored in
master's NOR flash.
3. Master's u-boot image should be generated specifically by
make xxxx_SRIOBOOT_MASTER_config
4. Master must boot first, and then slave can be powered on.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
When defined CONFIG_ENV_IS_NOWHERE, there will be some
compilation errors:
./common/env_nowhere.o: In function `env_relocate_spec':
./common/env_nowhere.c:38: multiple definition of `env_relocate_spec'
./common/env_flash.o: ./common/env_flash.c:326: first defined here
./common/env_nowhere.o: In function `env_get_char_spec':
./common/env_nowhere.c:42: multiple definition of `env_get_char_spec'
./common/env_flash.o:./common/env_flash.c:78: first defined here
./common/env_nowhere.o: In function `env_init':
./common/env_nowhere.c:51: multiple definition of `env_init'
./common/env_flash.o:./common/env_flash.c:237: first defined here
make[1]: *** [./common/libcommon.o] Error 1
make[1]: Leaving directory `./common'
make: *** [./common/libcommon.o] Error 2
Remove the CONFIG_ENV_IS_IN_FLASH if defined CONFIG_ENV_IS_NOWHERE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Add env in NAND support when boot from NAND.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
New P2041RDB board will add a NAND chip, so add support for NAND and
NAND boot.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
P1010RDB and p1_pc_rdb_pc has incorrect configuration for
CONFIG_DDR_RAW_TIMING. It should be CONFIG_SYS_DDR_RAW_TIMING.
Incorrect setting causes DDR failure in case of SPD absent.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Earlier, a driver exists in the u-boot source for designware i2c interface. That
driver was specific to spear platforms. This patch implements the i2c controller
as a generic driver which can be used by multiple platforms
The driver files are now renamed to designware_i2c.c and designware_i2c.h and
these are moved into drivers/i2c folder for reusability by other
platforms
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
board:
Add config file of board adp-ag102
Add adp-ag102 into boards.cfg
Add adp-ag102 into MAINTAINERS
doc:
add README of ag102
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
When calling board_late_init, we need to define CONFIG_BOARD_LATE_INIT.
The latest ecovec config defines BOARD_LATE_INIT, board_late_init is not called.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* 'master' of git://git.denx.de/u-boot-arm:
ARM926EJS: Fix cache.c to comply with checkpatch.pl
ARM926EJS: Make asm routines volatile in cache ops
MX35: mx35pdk: wrong board revision
ARM1136: MX35: Make asm routines volatile in cache ops
ARM: add u-boot.imx as target for i.MX SOCs
M28: Pull out CONFIG_APBH_DMA so it's always enabled
DMA: Split the APBH DMA init into block and channel init
imx: Return gpio_set_value in gpio_direction_output
imx: Use GPIO_TO_PORT macro in the gpio driver instead of (gpio >> 5)
imx: Add GPIO_TO_PORT macro in the mxc_gpio driver
imx: Remove unneeded/repititive definitions from imx headers
i.MX28: Allow coexistence of PIO and DMA mode for SD/MMC
MX31: mx31pdk: drop enable_caches from board file
i.MX28: Fix initial stack pointer position
mx35: mx35pdk: fix when cache functions are linked
mx35: flea3: fix when cache functions are linked
ARM: 926ejs: use debug() for misaligned addresses
ARM1136: add cache flush and invalidate operations
mx6qsabrelite: Fix the serial console port
mx6qsabrelite: Add boot switch setting information into the README
i.MX6: mx6qsabrelite: add cache commands if cache is enabled
i.MX6: implement enable_caches()
i.MX6: define CACHELINE_SIZE
MX53: DDR: Fix ZQHWCTRL field TZQ_CS
mx28evk: Add a README file
mx28: Split the README into a common part and a m28 specific part
tricorder: Load kernel from ubifs
tricorder: Add UBIFS
cm-t35: fix Ethernet reset timing
hawkboard: Add CONFIG_SPL_LIBGENERIC_SUPPORT
BeagleBoard: Remove userbutton command and use gpio command instead
OMAP: Move omap1510inn to Unmaintained / Orphaned
The board revision is detected accessing to the pmic,
that is not available before relocation (I2C).
This generates the following error:
CPU: Freescale i.MX35 rev 2.0 at 532 MHz.
Reset cause: WDOG
<reg num> = 7 is invalid. Should be less than 0
Board: MX35 PDK 1.0
The revision number is wrong, as a default value is printed
(tested on a mx35pdk Rev. 2.0).
Move the output in the board_late_init(), when
pmic can be accessed.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The ABPH DMA is now used also by the SD card. Therefore it has to be enabled
even if NAND is disabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
The patch:
m28evk: Use GENERATED_GBL_DATA_SIZE
commit 1084606c97
introduced usage of GENERATED_GBL_DATA_SIZE and calculation of initial stack
pointer position defived from that. Due to a small typo, the SP position moved
to 0x21f80, which is past the SRAM area. This didn't manifest on the real
hardware as the SRAM repeats there (address bits in the CPU being ignored).
Though this was caught in QEMU, where it crashed the emulator.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Since kernel should be in a ubifs partition, we need UBIFS.
The greater malloc size is needed for UBIFS.
Signed-off-by: Bernhard Walle <walle@corscience.de>
Squashed two commits (UBIFS enabled and malloc size increased) into one.
Signed-off-by: Thomas Weber <weber@corscience.de>
Remove userbutton command and do the detection in board config file using the gpio command
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Fix typo on CONFIG_SYS_HUSH_PARSER and also add CONFIG_SYS_PROMPT_HUSH_PS2
to avoid build error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* 'marek.vasut@gmail.com' of git://git.denx.de/u-boot-staging:
LMB: Fix undefined lmb_reserve() on non-lmb platforms
MIPS: fix endianess handling
MIPS: fix inconsistency in config option for cache operation mode
MIPS: board.c: fix init of flash data in bd_info
* 'master' of git://git.denx.de/u-boot-net:
net/designware: Change timeout loop implementation
net/designware: Set ANAR to 0x1e1
net/designware: Program phy registers when auto-negotiation is ON
net/designware: Try configuring phy on each dw_eth_init
net/designware: Consecutive writes must have delay
net/designware: Phy address fix
net/designware: Fix the max frame length size
net/designware: Fix to restore hw mac address
microblaze: Wire up LL_TEMAC driver initialization
microblaze: Add faked LL_TEMAC driver configuration
microblaze: Enable several ethernet driver compilation
net: ll_temac: Add LL TEMAC driver to u-boot
Update net subsystem maintainer in doc/git-mailrc
net/eth.c: fix eth_write_hwaddr() to use dev->enetaddr as fall back
mvgbe: remove warning for unused methods
* 'master' of git://git.denx.de/u-boot-onenand:
onenand: samsung: Enable OneNAND support at Samsung's Exynos4210
onenand: Replace ONENAND_IS_MLC() with ONENAND_HAS_4KB()
onenand:samsung OneNAND chip probe functions added for GONI and Exynos4210
onenand:samsung Target dependent OneNAND chip probe function
* 'master' of git://git.denx.de/u-boot-nios:
nios2 - adjust gbl data off to account for bd_info
nios2: implement get_ticks and get_tbclk
nios2: add flush_dcache_range function
Enable OneNAND support for Exynos4210 (C210 universal).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
U-Boot's multipple network supports enables to use
several ethernet drivers but microblaze-generic
platform config file select only one driver.
Reported-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Stephan Linz <linz@li-pro.net>
Make endianess of target CPU configurable. Use the new config
option for dbau1550_el and pb1000 boards.
Adapt linking of standalone applications to pass through
endianess options to LD.
Build tested with:
- ELDK 4 mips_4KC- and mips4KCle
- Sourcery CodeBench Lite 2011.03-93
With this patch all 26 MIPS boards can be compiled now in one step by
running "MAKEALL -a mips".
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
lzma: fix printf warnings
Remove CONFIG_SYS_EXTBDINFO from snapper9260.h
cmd_pxe.c: fix strict-aliasing warnings
net: smc91111: use mdelay()
doc: Fix some typos in different files
disk/part.c: Fix device enumeration through API
mkenvimage: Really set the redundant byte when applicable
mkenvimage: Don't try to detect comments in the input file
mkenvimage: Use mmap() when reading from a regular file
mkenvimage: Read/Write from/to stdin/out by default or if the filename is "-"
mkenvimage: More error handling
mkenvimage: Correct an include and add a missing one
mkenvimage: correct and clarify comments and error messages
MAKEALL: display SPL size if present
ARMV7/Vexpress: add missing get_ticks() and get_tbclk()
mkenvimage: fix usage message
cmd_fat: add FAT write command
fs/fat/fat_write.c: Fix GCC 4.6 warnings
FAT write: Fix compile errors
* 'master' of git://git.denx.de/u-boot-arm: (146 commits)
arm: Use common .lds file where possible
arm: add a common .lds link script
arm: Remove unneeded setting of LDCSRIPT
Define CPUDIR for the .lds link script
arm: Remove zipitz2 link script
Allow arch directory to contain .lds without requiring Makefile
OMAP: Remove omap1610inn-based boards
arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix build warnings
board/ti/beagle/beagle.c: Fix build warnings
sdrc.c: Fix typo in do_sdrc_init() for SPL
tegra: i2c: Add I2C driver
tegra: fdt: i2c: Add extra I2C bindings for U-Boot
tegra: i2c: Select I2C ordering for Seaboard
tegra: i2c: Enable I2C on Seaboard
tegra: i2c: Select number of controllers for Tegra2 boards
tegra: i2c: Initialise I2C on Nvidia boards
tegra: Enhance clock support to handle 16-bit clock divisors
fdt: Add function to allow aliases to refer to multiple nodes
tegra: Rename NV_PA_PMC_BASE to TEGRA2_PMC_BASE
tegra: fdt: Enable FDT support for Ventana
tegra: fdt: Enable FDT support for Seaboard
tegra: usb: Enable USB on Seaboard
tegra: usb: Add common USB defines for tegra2 boards
tegra: usb: Add USB support to nvidia boards
arm: Check for valid FDT after console is up
fdt: Avoid early panic() when there is no FDT present
tegra: usb: Add support for Tegra USB peripheral
tegra: fdt: Add function to return peripheral/clock ID
usb: Add support for txfifo threshold
tegra: usb: fdt: Add USB definitions for Tegra2 Seaboard
tegra: usb: fdt: Add additional device tree definitions for USB ports
tegra: fdt: Add clock bindings for Tegra2 Seaboard
tegra: fdt: Add clock bindings
tegra: fdt: Add additional USB binding
fdt: Add tegra-usb bindings file from linux
fdt: Add staging area for device tree binding documentation
tegra: fdt: Add device tree file for Tegra2 Seaboard from kernel
tegra: fdt: Add Tegra2x device tree file from kernel
arm: fdt: Add skeleton device tree file from kernel
fdt: Add basic support for decoding GPIO definitions
fdt: Add functions to access phandles, arrays and bools
fdt: Tidy up a few fdtdec problems
fdt: Add tests for fdtdec
fdt: Add fdtdec_find_aliases() to deal with alias nodes
arm: Tegra2: Fix ELDK42 gcc failure with inline asm stack pointer load
net: fec_mxc: allow use with cache enabled
net: force PKTALIGN to ARCH_DMA_MINALIGN
i.MX28: Enable caches by default
i.MX28: Make use of the bounce buffer
i.MX28: Do data transfers via DMA in MMC driver
MMC: Implement generic bounce buffer
i.MX28: Add cache support to MXS NAND driver
i.MX28: Add cache support into the APBH DMA driver
ARM926EJS: Implement cache operations
board/vpac270/onenand.c: Fix build errors
nhk8815: fix build errors
atmel-boards: add missing atmel_mci.h
ARM: highbank: setup env from boot source register
ARM: highbank: change env config to use nvram
ARM: highbank: add reset support
ARM: highbank: Add boot counter support
ARM: highbank: change TEXT_BASE to 0x8000
ARM: highbank: fix us_to_tick calculation
ARM: highbank: add missing get_tbclk
ARM: highbank: fix warning for calxedaxgmac_initialize
net: calxedaxgmac: fix build due to missing __aligned definition
EXYNOS: Add structure for Exynos4 DMC
EXYNOS: SMDK5250: Support all 4 UARTs
ARM: fix s3c2410 timer code
ARM: davinci: fixes for cam_enc_4xx board
omap3_spi: receive transmit mode
calimain, enbw_cmc: Fix typo in comments
Davinci: ea20: use gpio framework to access gpios
OMAP3: mt_ventoux: sets its own mtdparts
OMAP3: mt_ventoux: updated timing for FPGA
twl4030: fix potential power supply handling issues
NAND: TI: fix warnings in omap_gpmc.c
cam_enc_4xx: Rename 'images' to 'imgs'
arm: Add Prep subcommand support to bootm
OMAP3: twister: add support to boot Linux from SPL
SPL: call cleanup_before_linux() before booting Linux
OMAP3: SPL: do not call I2C init if no I2C is set.
Add cache functions to SPL for armv7
devkit8000: Implement and activate direct OS boot
omap/spl: change output of spl_parse_image_header
omap-common/spl: Add linux boot to SPL
devkit8000/spl: init GPMC for dm9000 in SPL
omap-common: Add NAND SPL linux booting
devkit8000: add config for spl command
Add cmd_spl command
mx53ard: Initialize return code with error
mx53: Make PLL2 to be the parent of UART clock
configs: imx: Use CONFIG_SF_DEFAULT_CS
mx28evk: Provide default values for SPI bus and chip select
USB: ehci-mx6: Add proper IO accessors
mx6: Read silicon revision from register
i.MX28: Drop __naked function from spl_mem_init
mxs_spi: Return proper timeout error
i.MX28: Make the stabilization delays shorter
pmic_i2c: Return error in case of invalid pmic_i2c_tx_num
mx6: Remove duplicate definition of ANATOP_BASE_ADDR
mx6: Fix reset cause for Power On Reset case
i.MX6: mx6qsabrelite: add MACH_TYPE_MX6Q_SABRELITE
i.MX6: mx6q_sabrelite: add CONFIG_REVISION_TAG
i.MX28: Enable additional DRAM address bits
mx6q: mx6qsabrelite: setup_spi() should be called in board_init to allow use for environment
mx31: add "ARM11P power gating" to get_reset_cause
mx31pdk: Fix CONFIG_SYS_MEMTEST_END
efikamx: Fix CONFIG_SYS_MEMTEST_END
mx53smd: Fix CONFIG_SYS_MEMTEST_END
mx53evk: Fix CONFIG_SYS_MEMTEST_END
mx51evk: Fix CONFIG_SYS_MEMTEST_END
i.MX6: mx6qsabrelite: add ext2 support
imximage: Remove overwriting of flash_offset
IXP: Fix GPIO_INT_ACT_LOW_SET()
IXP: Fix NAND build warning on PDNB3 and SCPU
IXP: Move PDNB3 and SCPU from Makefile to boards.cfg
IXP: Squash warnings in IXP NPE
IXP: Fix missing MACH_TYPE_{ACTUX?,PNB3,DVLHOST}
IXP: Make IXP buildable with arm-linux- toolchains
Examples: Properly append LDFLAGS to LD command
SPL: Enable YMODEM support on BeagleBone and AM335x EVM
SPL: Add YMODEM over UART load support
SPL: Add README.omap3
README: document more SPL config options
spl.c: Use __noreturn decorator
config.mk: Check for -fstack-usage support
config.mk: Make cc-option create a file under include/generated
...
The CS_AUTOBOOT configurations have been broken for a long time.
Kshitij Gupta is no longer at TI making these broken and orphaned
boards, so remove.
Signed-off-by: Tom Rini <trini@ti.com>
This enables I2C on Seaboard.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra 2x SOC has four ports, so define TEGRA_I2C_NUM_CONTROLLERS
in the shared config file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This switches Ventana over to use FDT for run-time config instead of
CONFIG options.
At present Ventana does not have its own device tree file - it just uses
the Seaboard one.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This switches Seaboard over to use FDT for run-time config instead of
CONFIG options. USB is the only user at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Seaboard has a top port which is USB host or device, and a side port which
is host only.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
All Tegra2 boards should include tegra2-common. This adds the required
USB config to that file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Update the highbank config to use env from NVRAM. Also remove extra env
settings as they are not used unless the default env is used.
Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Make some space at the beginning of RAM so the FDT can be loaded to a
known fixed address at 0x1000.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
- change CONFIG_ENV_RANGE to contain 2 nand erase blocks,
one for bad block reserve.
- remove from the envvariable "img_writeramdisk" the
ubifsmount command, as it is not needed.
- erase the hole mtd partition containing u-boot
- save environment variable "dvn_app_vers" and "dvn_boot_vers"
only after installing the new image.
changes requested from Marek Vasut:
- arm, davinci: fix eldk-4.2 warnings for cam_enc_4xx board
- get rid of run_command2 usage
needed since patch:
commit 009dde1955
Author: Simon Glass <sjg@chromium.org>
Date: Tue Feb 14 19:59:20 2012 +0000
Rename run_command2() to run_command()
is now in mainline.
- add CONFIG_SPL_LIBGENERIC_SUPPORT support
- remove CONFIG_CMD_PXE support
- fix warning:
cam_enc_4xx.c: In function 'menu_handle':
cam_enc_4xx.c:609: warning: dereferencing type-punned pointer
will break strict-aliasing rules
- fix error:
arm-linux-ld: u-boot-spl: Not enough room for program headers,
try linking with -N
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Fletzer Martin <Martin.Fletzer@ait.ac.at>
Cc: Wolfgang Denk <wd@denx.de>
Drop direct access to SOC's registers and use
the function of the GPIO driver for da8xx.
[Tom: Remove gpio[68]_base as it's now unused]
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Bastian Ruppert <Bastian.Ruppert@Sewerin.de>
CC: dzu@denx.de
CC: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Simon Schwarz <simonschwarzcor@gmail.com>
- Implements spl_start_uboot() for devkit8000
- Add configs to activate direct OS boot from SPL
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
This adds some configs for devkit8000 to use the new spl command
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
This feature is not available on ARM, so it is an error to define it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefano Babic <sbabic@denx.de>
Enable phylib and mii support for AXI EMAC
ethernet drivers on Microblaze systems.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Michal Simek <monstr@monstr.eu>
CONFIG_SPI_FLASH_CS is not used anywhere.
Use CONFIG_SF_DEFAULT_CS instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Provide default values for SPI bus and chip select.
This allows the command "sf probe" to work without passing SPI bus and chip
select numbers as arguments.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
This is needed to support Freescale-supplied userspaces.
At the moment, both the IPU and VPU libraries provided by Freescale
in the "imx-lib" package contain routines which scrape the system
revision from /proc/cpuinfo. In the VPU library, this information is
used to load the proper firmware, allowing a single binary to be used
across various i.MX processors.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
These symbols are no longer defined in Linux-ARM's mach-types files. Replace
these with CONFIG_MACH_TYPE instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
CONFIG_SYS_INIT_SP_ADDR points to RAM, but it's used before
DRAM controller init. Fix it by setting CONFIG_SYS_INIT_SP_ADDR
to SRAM
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
The sh7757lcr has 2GByte eMMC chip. This patch supports it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The earlier usb device controller driver was specific to spear platforms. This
patch implements the usb device controller driver as a generic controller which
can be reused by other platforms using this peripheral.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Marek Vasut <marex@denx.de>
This patch adds support for the esd CPCI-HD/2 board to u-boot for CPCI-CPU/750.
As the primary devices on the CPCI-HD/2 board are connected to device 1 and 3,
the device must be swapped.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
* 'master' of git://git.denx.de/u-boot-avr32:
atmel_mci.h: remove outdated register macros
doc/git-mailrc: add <me> to avr32 alias
ATMEL: remove old atmel_mci driver
ATMEL: use generic mmc framework
gen_atmel_mci works on AVR32 as well, so no need to use the legacy
mmc driver. This also has the nice side effect of being able to use
SDHC cards an those boards.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Enable fdt code and safe snprintf() options for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The generalised calculation of the serial bit rate reg also applies
to sh7264, it was just the clock speed that was set incorrectly.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add PREBOOT, SILENT_CONSOLE and DEVICE_NULLDEV for release
build. Fixed bug in CONFIG_SYS_HUSH_PARSER define.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
The video setup for the Epson display is provided. Addtionally
some extra info is displayed next to the Linux logo.
Make get_cpu_rev() publicly available (added to sys_proto.h).
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Define CONFIG_PHY_MICREL, and
minimize the tx clock delay.
There is an issue with 1000 baseTx mode on early revs
of the SabreLite boards. The center tap pin 9 of the mag RJ45
USB combo was connected to the 3.3 filtered supply. Letting
this pin float solved the problem. Symptoms of the problem
were packets with many extra zeroes tacked on the end, and random
bit flips causing a high rate of CRC errors. 10/100 baseTx worked
fine on all revs. To disable 1000 baseTx for these boards, simply
define the environment variable disable_giga. ie.
setenv disable_giga 1
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
The Integrator/CP config file was very outdated and gives a
non functional U-Boot. So:
- Set the CONFIG_ARCH_CINTEGRATOR arch flag correctly
- Add proper core module configuration options
- Skip cluttered command lista and just include
<config_cmd_default.h>
- Kill off #if 0 network section and insert some example
configuration that simply just boots from the network
using TFTP if available.
- Delete flash control registers that have no business
in this config file. These are already moved down to
board/armltd/integrator/integrator-sc.h
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PCI support for the Integrator AP has apparently never
been finished and I strongly suspect that it has never worked,
so let's fix it. This is a list of the more or less
un-splittable changes done in this driver rewrite:
- Replace the register definitions stashed into the config
file (!) with a copy if the register file from the Linux
kernels arch/arm/include/asm/hardware/pci_v3.h
- Delete the unreadable gigantic macros that perform the
config accesses and replace them with copyedited code from
Linux arch/arm/mach-integrator/pci_v3.c
- Rewrite the rest of the setup code to use the
v3_[read|write][lwb]() accessors.
- Enable PCI by default in the AP board configuration.
- Fix checkpatch warnings and make code more conformant.
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In commit 2d575e4685 a separate header
file was introduced for the DM6467T EVM, include/configs/davinci_dm6467Tevm.h.
The substantial difference between the davinci_dm6467evm and the
davinci_dm6467Tevm configuration is a single bit in the hardware revision
that is passed to the Linux kernel and davinci_dm6467evm has
REFCLK_FREQ = 27000000 where as davinci_dm6467Tevm.h has a
REFCLK_FREQ = 33000000.
This patch removes include/configs/davinci_dm6467Tevm.h. Instead the
include/configs/davinci_dm6467evm.h configuration is used for DM6467T EVMs and
renamed CFG_REFCLK_FREQ to CONFIG_REFCLK_FREQ and CONFIG_REFCLK_FREQ is defined
in boards.cfg.
Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Tom Rini <trini@ti.com>
Because the tricorder uses the CONFIG_OMAP_HSMMC the
initialization command is mmc rescan and not mmc init.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tom Rini <trini@ti.com>
The default settings store the persistent environment on SD card
and not serial flash (SPI NOR).
To use SPI NOR to save the environment instead of SD card, edit
include/configs/mx6qsabrelite.h and
- undefine CONFIG_ENV_IS_IN_MMC
- define CONFIG_ENV_IS_IN_SPI_FLASH
The SPI driver can take as chip select the controller's chip selects
as well as an external GPIO. The LSB byte has the value of the internal
chip select, the highest (thought as 16-bit value) contains the GPIO
number.
The GPIO used on Sabre Lite is GP3:19 == 83.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Jason Liu <jason.hui@linaro.org>
Tested-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
Tested-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
Tested-by: Jason Liu <jason.hui@linaro.org>
This patch adds SPI support for the MX28EVK. Support for
an optionally installed SPI flash is also added. An example
configuration for redundant envrionment from SPI flash is also
added but disabled by default.
This patch has been tested on a MX28EVK Rev. D with an installed
SST25VF032B 32Mbit SPI flash.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch enables USB host support on the MX28EVK board.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch adds support for the MX28 internal RTC
and enables u-boot's date command.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
* Adjust the GBL_DATA_OFFSET to account for the fact that we'll be
using the space between that offset and the start of the malloc
region to allocate both a gd structure and a board info structure.
* This fixes a memory corruption bug due to overlap of the malloc
region and the bd_info structure.
Signed-off-by: Alex Hornung <alex@alexhornung.com>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
* 'master' of git://git.denx.de/u-boot-blackfin:
Blackfin: pata_bfin: fix printf warning
Blackfin: bfin_nand: mark local func static
linkage.h: move from blackfin to common includes
Blackfin: br4: new board port
Blackfin: add in/out le32 variants
post: add blackfin to the post_time_ms list
Blackfin: bf537-stamp: drop board reset workaround
Blackfin: pr1: new board port
This adds support for the BR4 Appliance. It is a quad channel ISDN BRI
board based on Blackfin BF537 CPU.
Signed-off-by: Dimitar Penev <dpn@switchfin.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This add support for the PR1 Appliance - Asterisk based ISDN PRI PBX.
This board is Blackfin BF537 based. The schematics are not fully opened.
Signed-off-by: Dimitar Penev <dpn@switchfin.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch adds support for the Calimain board from
OMICRON electronics GmbH. The board features a Texas Instruments AM1808
SoC, 128 MB DDR2 memory, and 64 MB NOR flash memory connected to CS2 and
CS3.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
This patch moves hawkboard to the new spl infrastructure from the
older nand_spl one.
Removed the hawkboard_nand_config build option -- The spl code now
gets compiled with hawkboard_config, after building the main u-boot
image, using the CONFIG_SPL_TEXT_BASE. Modified the README.hawkboard
to reflect the same.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
The V bit of the c1 register of CP15 should not be cleared on DA850
SoCs since they have no valid memory at 0x00000000. This patch
introduces a configuration option CONFIG_SYS_EXCEPTION_VECTORS_HIGH
that allows setting the correct value for the V bit.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Reported-by: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
This patch reverts commit ca4b55800e
"arm, arm926ejs: always do cpu critical inits" since it impacts all
arm926ejs based configurations and caused problems, e.g., with
the hawkboard.
Instead the patch removes the CONFIG_SKIP_LOWLEVEL_INIT defines
from the board configurations that need low level initialization.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
add support for printing various clock frequency info found
in SOC such as ARM core frequency, DSP core frequency and DDR
frequency as part of bdinfo command.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
remove the macro CONFIG_DISPLAY_CPUINFO as it is no longer
required. This is because clock info will be printed as part
'bdinfo' command and also remove support print_cpuinfo() as it will
no longer be called.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
This patch adds support for the HTKW mcx AM3517-based board.
Serial, Ethernet, NAND, MMC, RTC, EHCI USB host and both
NAND and MMC SPLs are supported.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
Cc: Detlev Zundel <dzu@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The mt_ventoux board is a custom board using
the Technexion TAM3517 module.
The patch fixes also the mtdparts variable in the
TAM3517 common configuration file.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Ilya Yanok <yanok@emcraft.com>
CC: Igor Grinberg <grinberg@compulab.co.il>
CC: Tom Rini <tom.rini@gmail.com>
Cc: Detlev Zundel <dzu@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Changed the EHCI interface using the ulpi framework.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
For panda initialise the mux pins for ehci usage and
enable ehci in omap4_panda config file.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Based on discussion from this thread [1].
Adding omap-view port that helps us in using the generic ulpi
framework for any ulpi phy ops using the INSNREG05_ULPI viewport
reg available on omap platform.
Currently ehci ports are available on omap3/4 platforms so enable the same
for beagle and panda, patch is tested on the same boards.
Thanks to Igor Grinberg <grinberg@compulab.co.il> for reviewing the
omap-ehci patches and suggesting this approach.
[1]: http://www.mail-archive.com/u-boot@lists.denx.de/msg76076.html
Tested-by: Stefano Babic <sbabic@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
This patch enable support for SMC911X based ethernet device.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds support for MMC SPL booting.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
SMDK5250 board is based on Samsungs EXYNOS5250 SoC.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
CONFIG_SYS_CLK_FREQ_C210 macro giving notion of S5PC2XX (Exynos4)
architecture. Replace CONFIG_SYS_CLK_FREQ_C210 with CONFIG_SYS_CLK_FREQ
to make it generic for exynos architecture.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since MACH_TYPE_ORIGEN is updated on mach-types,
remove the MACH_TYPE_ORIGEN on config file.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Chander Kashyap <chander.kashyap@linaro.org>
This patch adds support for Samsung TRATS board
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We don't need 3us delay for our i2c bus. Decrease it to 1us.
It would also be possible to use 100ns in the future, but
currently kirkwood has no ndelay implementation.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
This patch adds support for D-Link DNS-325 ShareCenter NAS.
Signed-off-by: Stefan Herbrechtsmeier <stefan@code.herbrechtsmeier.net>
Cc: prafulla@marvell.com
Cc: albert.u.boot@aribaud.net
board_mmc_init() initializes the pins of SDHC1 and
turns on V_MMC1 of the PMIC. Config adds support for EXT2
and FAT.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
CONFIG_NET_MULTI is not used anymore, so remove it from board files.
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Stefano Babic <sbabic@denx.de>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Eric Miao <eric.miao@linaro.org>
CC: Jason Liu <jason.hui@linaro.org>
CC: Stefano Babic <sbabic@denx.de>
To be able to load the device tree and initrd correctly, set
the fdt_high and initrd_high environment variables.
Using 0xffffffff implies that the device tree and the initrd
are initially copied to working addresses. This will avoid an
additional copy.
Loading the device tree to 0x30000000 and the initrd to 0x3c000000
should work for both boards, the ARM2 and SabreLite.
Example (SabreLite):
fatload mmc 0:2 0x10000000 uImage
fatload mmc 0:2 0x3c000000 uInitrd
fatload mmc 0:2 0x30000000 board.dtb
bootm 0x10000000 0x3c000000 0x30000000
Note: This requires that the kernel has CONFIG_HIGHMEM enabled.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Jason Liu <jason.hui@linaro.org>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
