The size of SPL is hitting the limit (64KB) for uniphier_v7_defconfig.
When booting from SD/eMMC, obviously its clock has been properly set up
by the boot ROM. Acutually, no need to re-initialize the clock in SPL.
Using a clock driver would generalize the SoC specific code, but
solving the memory footprint problem would win.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I need to differentiate the clock handling for uniphier-sd. Move it
to each driver's probe function from the tmio common code so that
renesas-sdhi will not be affected.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Odroid C2 fails to read from mmc with U-Boot v2018.03.
The change avoids a division by zero.
The fix was suggested by Jaehoon in
https://lists.denx.de/pipermail/u-boot/2018-January/318577.html
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Suggested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
U-boot driver for sunxi-mmc uses PLL6, unlike linux kernel where
PLL5 is used, with clock rates respectively 600MHz and 768MHz.
Thus there are different phase degree steps - 24 for the kernel and
30 for u-boot.
In the kernel driver the phase is set 90 deg for output and 120 for
sample. Dividing by 30 will result values 3 and 4. Those are the
values set in the u-boot driver.
However, the condition defining delays is wrong. MMC core driver
requests clock of 52MHz, sunxi-driver sets clock of 50MHz, but
phase is set 30 deg for output and 120 deg for sample.
Apparently this works for most cards.
On A20-SOM204-EVB-eMMC there is eMMC card (KLMAG2GEND) which complains
about it. Maybe there is other boards with similar problem?
So the fix is to match delays for both u-boot and kernel.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add MMC DM and DT probing support into the SH MMCIF driver.
This patch abstracts out the common bits of the send command
and set ios functions, so they can be used both by DM and non
DM setups and adds the DM probe support.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The mv_sdhci driver was not zeroing the sdhci_host structure it
allocates causing random access violations in parts of the mmc core
where the "ops" member pointers are checked and called if not NULL.
Signed-off-by: Matt Pelland <mpelland@starry.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Synchronize the naming with Linux, call the common code TMIO.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The IP requires some time to recuperate after the IO pin
properties were changed. Add a delay to assure this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix minor rebase omission, the else was missing which triggered
two accesses to the register on 64bit variant of the IP.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Make sure to wait for the command to complete altogether, including
the trailing 8 clock cycles. This prevents the driver for accidentally
writing the CMD register too fast before the previous command fully
completed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The HOST_MODE register must be set to 0 when the IP is operated in 16bit
mode, otherwise 16bit access to the data FIFO may fail.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
There are only a few registerse used in the 16bit mode which are
32bit internally. Special-case only those in the IO accessors and
always write both halves. Any other register access is protected
from accidentally overwriting neighboring register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add code for PHY tuning required for SDR104/HS200 support on Renesas RCar.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Export the matsu_sd_{read,write}l() common register access
functions, so that they can be used by other drivers sharing
the common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Factor out the regulator handling into set_ios and add support for
selecting pin configuration based on the voltage to support UHS modes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Handle the controller version even if quirks are set. The controller in
Renesas Gen3 SoCs does provide the version register, which indicates a
controller v10 and the controller does support internal DMA and /1024
divider.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Handle bus width 0 as 1-bit bus to assure valid content of
MATSU_SD_OPTION register WIDTH field.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The DMA READ completion flag position differs on Socionext and Renesas
SoCs. It is bit 20 on Socionext SoCs and using bit 17 is a hardware bug
and forbidden. It is bit 17 on Renesas SoCs and bit 20 does not work on
them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
On the Renesas version of the IP, the /1 divider is realized by
setting the clock register [7:0] to 0xff instead of setting bit
10 of the register. Check the quirk and handle accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a quirk to identify that the controller is Renesas RCar variant
of the Matsushita SD IP and another quirk indicating it can support
Renesas RCar HS200/HS400/SDR104 modes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Drop the ad-hoc DT caps parsing in favor of common framework function.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The Renesas RCar Gen2 chips have a mix of 32bit and 16bit variants
of the IP. There is no DT property which allows discerning those,
so what Linux does is it checks the size of the register area and
if it is 0x100, the IP is 16bit, otherwise the IP is 32bit. Handle
the distinction the same way.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Certain instances of the SD IP require more elaborate digging
in the DT to figure out which variant of the SD IP is in use.
Allow explicit passing of the quirks into the probe function.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add support for 16bit mutation of the Matsushita SD IP. Since some
registers are internally 32bit, the matsu_sd_{read,write}l() has
to special-case this 16bit variant a bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Drop useless check in matsu_sd_{read,write}q(), this is only ever
called to read the data from FIFO and only when 64bit variant of
the block is used anyway.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add macros to generate the FIFO accessors, since the code is almost
the same with only minor differences. This is done in preparation
for adding 16bit variant of the IP.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add Kconfig entry for the Renesas SDHI variant of the controller
and split the Makefile entries accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Factor out common code from the uniphier SD driver, change the prefix
of the functions from uniphier_sd_ to matsu_sd_ and create separate
renesas-sdhi.c driver. Thus far, all the code is still compiled when
CONFIG_UNIPHIER_MMC is selected and there is no functional change.
This patch is a preparation for further split of the SoC specific
parts of the Matsushita SD driver, used both on Uniphier and R-Car.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
In raspberrypi-firmware 7fdcd00e00a42a1c91e8bd6f5eb8352fe9358557 and
later start.elf now sets the EMMC clock to 200 MHz.
According to Phil Elwell in
https://github.com/raspberrypi/firmware/issues/953
the SDHost controller shares the core/VPU clock and doesn't use
the EMMC clock.
Use the core clock id when determining the frequency to allow
U-Boot to work with recent versions of raspberrypi-firmware.
Otherwise U-Boot hangs at:
U-Boot 2018.03 (Mar 14 2018 - 20:36:00 +1100)
DRAM: 948 MiB
RPI 3 Model B (0xa02082)
MMC: mmc@7e202000: 0, sdhci@7e300000: 1
Loading Environment from FAT...
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use dm_pci_map_bar function for BAR mapping. This has the advantage
of clearing BAR flags and and only accepting mapped memory.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
nsd32_mmc was created to support ftsdc010 dm.
It is not necessary to separate both, so merge it
to ftsdc010.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Convert CONFIG_FTSDC010_SDIO to Kconfig.
So CONFIG_FTSDC010_SDIO can also be
removed from config_whitelist.txt.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Only three defconfig(adp-ag101p_defconfig,
adp-ae3xx_defconfig, nx25-ae250_defconfig)
set CONFIG_FTSDC010=y. And they all also
enable CONFIG_DM_MMC. So the non-dm code
of ftsdc010 can be dropped now.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
ftsdc010 dm driver has been disable High-Speed mode
as default to work around Andes AE3XX platform's problem,
because of it does not support High-Speed mode in
commit id 73cd56b2df.
But other platforms or SoCs maybe support this function.
So High-Speed mode can be enabled from dts with
cap-mmc-highspeed or cap-sd-highspeed property.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
The Rockchip-specific SDHCI wrapper does not process the 'bus-width'
property in the SDHCI node. Consequently, the bus is always kept in
4bit mode, even if 8bit wide operation is available, supported and
requested in the DTS.
This change adds processing of the 'bus-width' property and sets the
host capability flag for an 8bit wide bus, if set to 8. As the logic
in sdhci.c does not support clearing the 4bit capability, we assume
that 4bit operation is always supported.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds "st,pin-ckin" support to activate sdmmc_ckin feature.
When using an external driver (a voltage switch transceiver),
it's advised to select SDMMC_CKIN feedback clock input to sample
the received data.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The hardware flow control functionality is used to avoid
FIFO underrun (TX mode) and overrun (RX mode) errors.
The behavior is to stop SDMMC_CK during data transfer and
freeze the SDMMC state machines.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
With CONFIG_DM_MMC the BananaPi does not detect SD cards.
The sunxi device trees use the cd-inverted property to indicate that
the card detect is inverted.
This property is documented in Linux kernel devicetree/bindings/mmc/mmc.txt
The property is not marked as deprecated.
A similar patch was posted by Tuomas but is in status "Changes Requested".
https://patchwork.ozlabs.org/patch/850377/
This patch is a stripped down version of his patch.
Suggested-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MIN_FREQ
and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ
and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
mmc_of_parse() doesn't set a default value if none is available in DT.
In that case, use a default 52MHz clock rate.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some platforms don't have ADMA controllers. For those platforms, compiling
it out reduces the size of the binary by about 600 bytes.
Leaving the support in doesn't break things as the driver checks at runtime
if the ADMA2 controller is present.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This reduces the size of the binary by about 196 bytes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The area for struct mmc can be allocated dynamically. It greatly reduces
the size of struct omap_hsmmc_plat. This is useful in cases where the board
level code declares one or two struct omap_hsmmc_plat because it doesn't
use the Driver Model.
This saves around 740 bytes for the am335x_evm SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
MMC card with EXT_CSD_REV value 9 will trigger off-by-one
bug while accessing mmc_versions array. The patch fix that.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Add DT compatible strings for RCar Gen2 SoCs, so that this driver
can bind with them. Unlike Gen3, which uses 64bit FIFO, the Gen2
uses 16bit FIFO.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
If some configs are disabled, number of freqs array will not assigned to
correct value with bus_mode.
Synchornize the ordering with enum bus_mode in mmc.h.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
When using omap_hsmmc without the device model then the allocation
of mmc->priv ends up uninitialised.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
The correspondence between mmc versions as used in u-boot and the version
numbers reported in register EXT_CSD_REV is wrong for versions above and
including MMC_VERSION_4_41. All those versions were shifted by one:
real 4.5 hardware appeared to be MMC_VERSION_5_0.
Fix this by adding the missing version in the correspondence table.
Reported-by: eil Eilmsteiner Heribert <eil@keba.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
After settings the speed of the sd with the switch command, a check is
done to make sure that the new speed has been set. The current check has a
masking error: speed are encoded on 4 bits only.
Fix it by masking the upper bits.
This fixes a problem seen with QEmu emulating a vexpress-a15.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Jonathan Gray <jsg@jsg.id.au>
I/O data lines of UHS SD card operates at 1.8V when in UHS speed
mode (same is true for eMMC in DDR and HS200 modes). Add support
to switch signal voltage to 1.8V in order to support
UHS cards and eMMC HS200 and DDR modes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
mmc core has defined a new parameter *clk_disable* to gate the clock.
Disable the clock here if *clk_disable* is set.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
When the clock is applied, compute the actual value of the clock. It may be
slightly different from the requested value (max freq, divisor threshold)
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The default configuration is usually working fine for the the HS modes.
Don't enforce the presence of a dedicated pinmux for the HS modes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
AM572x SR1.1 requires different IODelay values to be used than that used
in AM572x SR2.0. These values are populated in device tree. Add
capability in omap_hsmmc driver to extract IOdelay values for different
silicon revision. The maximum frequency is also reduced when using a ES1.1.
To keep the ability to boot both revsions with the same dtb, those values
can be provided by the platform code.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met.
Add support to parse mux values and iodelay values from device tree
and set these depending on the enumerated MMC mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the mmc_of_parse library function to populate mmc_config instead of
repeating the same code in host controller driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
>From OMAP3 SoCs (OMAP3, OMAP4, OMAP5, AM572x, AM571x), the DAT/CMD lines
reset procedure section in TRM suggests to first poll the SRD/SRC bit
until it is set to 0x1. But looks like that bit is never set to 1 and there
is an observable delay of 1sec everytime the driver tries to reset DAT/CMD.
(The same is observed in linux kernel).
Reduce the time the driver waits for the controller to set the SRC/SRD bits
to 1 so that there is no observable delay.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
According to errata i802, DCRC error interrupts
(MMCHS_STAT[21] DCRC=0x1) can occur during the tuning procedure.
The DCRC interrupt, occurs when the last tuning block fails
(the last ratio tested). The delay from CRC check until the
interrupt is asserted is bigger than the delay until assertion
of the tuning end flag. Assertion of tuning end flag is what
masks the interrupts. Because of this race, an erroneous DCRC
interrupt occurs.
The suggested workaround is to disable DCRC interrupts during
the tuning procedure which is implemented here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200/SDR104 requires tuning command to be sent to the card. Use
the mmc_send_tuning library function to send the tuning
command and configure the internal DLL.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In order to enable DDR mode, Dual Data Rate mode bit has to be set in
MMCHS_CON register. Set it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the timing parameter set in the MMC core to set the
mode in UHSMS bit field. This is in preparation for
adding HS200 support in omap hsmmc driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
"ti,dual-volt" is used in linux kernel to set the voltage capabilities.
For host controller dt nodes that doesn't have "ti,dual-volt",
it's assumed 1.8v is the io voltage. This is not always true (like in
the case of beagle-x15 where the io lines are connected to 3.3v).
Hence if "no-1-8-v" property is set, io voltage will be set to 3v.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
No functional change. Move bus width configuration setting to a
separate function and invoke it only if there is a change in the
bus width.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a separate function for starting the clock, stopping the clock and
setting the clock. Starting the clock and stopping the clock can
be used irrespective of setting the clock (For example during iodelay
recalibration).
Also set the clock only if there is a change in frequency.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use pr_* log functions from Linux. They can be enabled/disabled
via CONFIG_LOGLEVEL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
config_fallbacks.h has some logic that sets HAVE_BLOCK_DEVICE
based on a list of enabled options. Moving HAVE_BLOCK_DEVICE to
Kconfig allows us to drastically shrink the logic in
config_fallbacks.h
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rename HAVE_BLOCK_DEVICE to CONFIG_BLOCK_DEVICE]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_APBH_DMA
CONFIG_APBH_DMA_BURST
CONFIG_APBH_DMA_BURST8
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
[trini: Add in MMC as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce SDR104 and HS200 support
The implementation takes linux kernel sdhci.c and sdhci-esdhc-imx.c
as reference.
- Implement esdhc_change_pinstate to dynamically change pad settings
- Implement esdhc_set_timing
- Implement esdhc_set_voltage to switch voltage
- Implement fsl_esdhc_execute_tuning to execute time process
- Enlarge the cfg->f_max to 200MHz.
- Parse fsl,tuning-step, fsl,tuning-start-tap and
fsl,strobe-dll-delay-target from device tree.
- Parse no-1-8-v property
- Introduce esdhc_soc_data to indicate the flags and caps
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add entries that will be used for tuning control.
The whole layout not changed, just expand reserved3[84] and
rename other reservedx in sequence.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The BCM2835 family of SoCs has 2 different SD controllers: One based on
the SDHCI spec and a custom, home-grown one.
This patch implements a driver for the latter based on the Linux driver.
This is needed so that we can make use of device trees that assume driver
presence of both SD controllers.
Signed-off-by: Alexander Graf <agraf@suse.de>
When clock is enabling, it's assigned to 0 as mmc->clock.
Then it can't initialize any card.
Fix to assign to correct clock value as mmc->cfg->f_min or f_max.
Fixes: 9546eb92cb ("mmc: fix the wrong disabling clock")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Guillaume GARDET <guillaume.gardet@free.fr>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
wait_for_bit callers use the 32 bit LE version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Commit 4f425280fa ("mmc: fsl_esdhc: Allow all supported prescaler
values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR mode on
i.MX, thus bypassing the SD clock frequency prescaler, in order to be
able to get higher SD clock frequencies in some contexts. However, that
commit missed the fact that this value is illegal on the eSDHCv3
instance of the i.MX53. This seems to be the only exception on i.MX,
this value being legal even for the eSDHCv2 instances of the i.MX53.
Fix this issue by changing the minimum prescaler value for the single
instance of the i.MX53 eSDHCv3 controller.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
When power is off, clock is not disabling.
Because it's passed to 1, mmc->clock should be set to f_min value.
Some drivers can't initialize the eMMC/SD card with current status.
This patch is to fix the disabling clock value to 0.
Fixes: 2e7410d76a ("mmc: disable the mmc clock during power off")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Guillaume GARDET <guillaume.gardet@free.fr>
Tested-by: Anand Moon <linux.amoon@gmail.com>
During the tuning, drivers repeat data transfer, changing timing
parameters in the controller hardware. So, the tuning commands
(CMD19 for SD, CMD21 for eMMC) fail, and this is not a problem
at all.
Showing "Error detected..." in normal operation just make users
upset. This should not be shown.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This line overwrites host_cap that has been set by drivers and/or
helpers like mmc_of_parse(). Accumulate capabilities flags.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
You must fix your DT if it specifies insane bus-width, for example,
bus-width = <3>;
debug() is not displayed in usual configuration, so people will not
even notice weirdness. Use dev_err() instead, then let it fail.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
mmc_of_parse() in U-Boot is a pussy helper; it sets cfg->f_max to
52MHz even if DT does not provide "max-frequency" at all. This can
overwrite cfg->f_max that may have been set to a reasonable default.
As the DT binding says, "max-frequency" is an optional property.
Do nothing if DT does not specify it. This is the behavior of
mmc_of_parse() in Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
omap_hsmmc driver uses "|" in a couple of places for disabling a bit.
While it's okay to use it in "mmc_reg_out" (since mmc_reg_out has a
_mask_ argument to take care of resetting a bit), it's incorrectly used
for resetting flags in "omap_hsmmc_send_cmd".
Fix it here by using "&= ~()" to reset a bit.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of sending STOP TRANSMISSION command from MMC core, enable
the auto command feature so that the Host Controller issues CMD12
automatically when last block transfer is completed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The omap hsmmc host controller can have the ADMA2 feature. It brings better
read and write throughput.
On most SOC, the capability is read from the hl_hwinfo register. On OMAP3,
DMA support is compiled out.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This reverts commit 46831c1a4c.
This reserved area at the beginning of struct hsmm, will be used later to
support ADMA
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Current USDHC driver will reset VSELECT to 0 (3.3v) during mmc init,
then set to 1 for 1.8v eMMC I/O. When booting from eMMC, since ROM has
already set VSELECT to 1.8v before running the u-boot. This reset in
USDHC driver causes a short 2.2v pulse on CMD pin.
Fix this issue by not reset VSELECT to 0 when 1.8v flag is set.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
hc_wp_grp_size is needed only if hardware partitionning is used.
On ARM removing it saves about 30 bytes of code space.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This information is only used by the "mmc info" command.
On ARM removing this information from SPL saves about 140 of code space.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Also remove erase_grp_size and write_bl_len from struct mmc as they are
not used anymore. On ARM, removing them saves about 100 bytes of code
space in SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The content of ssr is useful only for erase operations.
on ARM, removing sd_read_ssr() saves around 300 bytes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This allows using CONFIG_IS_ENABLED(MMC_WRITE) to compile out code
needed only if write support is required.
The option is added for u-boot and for SPL
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
struct mmc_data contains the block size to use for the data transfer.
Use this information instead of using the default value or the block length
information stored in struct mmc.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The SDcard initialization procedure does a few more things than it did earlier:
* switch the bus width even for 1-bit bus width
* check that speed has been properly set (in resp[4] of SD_CMD_SWITCH_FUNC)
Update the SD simulator to handle those requests gracefully.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Not all boards have an eMMC and not all users have a need for this.
Allow to compile it out. By default it is still included.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Supporting USH and HS200 increases the code size as it brings in IO voltage
control, tuning and fatter data structures.
Use Kconfig configuration to select which of those features should be
built in.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This allows to compile out the log message by tweaking the LOGLEVEL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Not using this function reduces the size of the binary. It's replaces by
a standard malloc() and the alignment requirement is handled by an
intermediate buffer on the stack.
Also make sure that the allocated buffer is freed in case of error.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The ext_csd is allocated only for MMC above version 4. The compare will
crash or fail for older MMCs.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Make sure that those basic capabilities are advertised by the host.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
As the legacy modes were not added to the list of supported modes, old
cards that do not support other modes could not be used.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
* convert to livetree API
* don't fail because of an invalid bus-width, instead default to 1-bit.
* recognize 1.2v DDR and 1.2v HS200 flags
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This is a useful information while debugging the initialization process or
performance issues.
Also dump this information with the other mmc info if the verbose option
is selected
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new function to parse host controller dt node and
set mmc_config. This function can be used by mmc controller
drivers to set the generic mmc_config.
This function can be extended to set other UHS mode caps
once UHS mode support is added.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200/SDR104 requires tuning command to be sent to the card.
Add a simple function to send tuning command and to read and
compare the received data with the tuning block pattern.
This function can be used by platform driver to perform DLL
tuning.
This patch is similar to
commit 996903de92f0 ("mmc: core: add core-level function for
sending tuning commands") added in linux kernel.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200 only supports 1.2v and 1.8v signal voltages. DDR52 supports 3.3v/1.8v
or 1.2v signal voltages.
Select the lowest voltage available when using those modes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
With certain SD cards like Kingston 8GB/16GB UHS card, it is seen that
MMC_CMD_ALL_SEND_CID cmd fails on first attempt, but succeeds
subsequently. Therefore, retry MMC_CMD_ALL_SEND_CID cmd a few time
as done in Linux kernel.
Similarly, it is seen that MMC_CMD_SET_BLOCKLEN may fail on first
attempt, therefore retry this cmd a few times as done in kernel.
To make it clear that those are optionnal workarounds, a new Kconfig
option 'MMC_QUIRKS' is added (enabled by default).
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Boot partitions do not support HS200. Changing to a lower performance mode
is required to access them.
mmc_select_mode_and_width() and sd_select_mode_and_width() are modified to
make it easier to call them outside of the initialization context.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If a power cycle cannot be done on Vcc, it is safer not to try the UHS
modes because we wouldn't be able to recover from an error occurring
during the UHS initialization.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add UHS modes to the list of supported modes, get the UHS capabilites of
the SDcard and implement the procedure to switch the voltage (UHS modes
use 1v8 IO lines)
During the voltage switch procedure, DAT0 is used by the card to signal
when it's ready. The optional card_busy() callback can be used to get this
information from the host driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add HS200 to the list of supported modes and introduce tuning in the MMC
startup process.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tuning is a mandatory step in the initialization of SDR104 and HS200 modes.
This callback execute the tuning process.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
There is no point in having the mmc clock enabled during
power off. Disable the mmc clock. This is similar to how it's
programmed in Linux Kernel.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
mmc clock has to be disabled in certain cases like during
the voltage switch sequence. Modify mmc_set_clock function
to take disable as an argument that signifies if the
clock has to be enabled or disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
mmc/sd specification requires vdd to be disabled for 1 ms
and then enabled again during power cycle. Add a
function in mmc core to perform power cycle and set
the io signal to it's initial state.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new callback function *send_init_stream* which start a sequence of
at least 74 clock cycles.
The mmc core uses *mmc_send_init_stream* in order to invoke the callback
function. This will be used during power cycle where the specification
requires such a sequence after power up.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new function *mmc_set_signal_voltage* in mmc core
which can be used during mmc initialization to select the
signal voltage. Platform driver should use the set_ios
callback function to select the signal voltage.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
set_ios callback has a return value of 'int' but the mmc_set_ios()
function ignore this. Modify mmc_set_ios() and the callers of mmc_set_ios() to
to return the error status.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The MMC startup process currently handles 4 modes. To make it easier to
add support for more modes, let's make the process more generic and use a
list of the modes to try.
The major functional change is that when a mode fails we try the next one.
Not all modes are tried, only those supported by the card and the host.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SDcard startup process currently handles only 2 modes. To make it
easier to add support for more modes, let's make the process more generic
and use a list of the modes to try.
The major functional change is that when a mode fails we try the next one.
Not all modes are tried, only those supported by the card and the host.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a simple helper function to display information (bus width and
mode) based on a capability mask. Useful for debug.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
no functionnal changes.
In order to add the support for the high speed SD and MMC modes, it is
useful to track this information.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This will be reused later in the selection of high speed and ddr modes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The ext csd is used for comparison many times. Keep a reference content
of the ext csd in the struct mmc to avoid reading multiple times
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
no functionnal change. This is only to further reduce the size o
mmc_startup().
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
No functionnal change here. The function is really big and can be split.
The part related to bus configuration are put in 2 separate functions: one
for MMC and one for SD.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Get a reference to the regulator devices from the dts and store them
in the struct mmc for later use.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
data is defined as struct mmc_data *data.
So it should not be compared to 0.
Problem identified with Coccinelle.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fixes emmc initialization regression on the db410c platform.
Clearing this register while SDHCI_PRESENT_STATE reports
SDHCI_CMD_INHIBIT leads to undefined behaviour on the db410c.
When commit 7dde50 was merged (mmc: sdhci: Wait for SDHCI_INT_DATA_END
when transferring), SDHCI transfers transitioned to wait for bit
SDHCI_INT_DATA_END before flagging transfers done.
Without this patch, the db410 platform fails to initialize its eMMC
due to all of its transfers timing out (SDHCI_INT_DATA_END is never
raised after all the blocks have been transferred).
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
This patch fixes some warnings when building boards that do not define
DM_I2C_COMPAT i.e. boards that entirely rely on the new i2c layer.
Signed-off-by: Felix Brack <fb@ltec.ch>
priv pointer should be freed before returning with an error value
from exynos_dwmci_get_config().
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Signed-off-by: Raghu Bharadwaj <raghu@techveda.org>
__be32_to_cpu() accepts argument of type __be32. This patch changes
type of the buffer in ALLOC_CACHE_ALIGN_BUFFER macro to __be32, which
is then passed to __be32_to_cpu().
This prevents sparse build warnings.
drivers/mmc/mmc.c: warning: cast to restricted __be32
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Signed-off-by: Karthik Tummala <karthik@techveda.org>
Add new compatible to the Uniphier SD driver for R8A77995 D3 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add new compatible to the Uniphier SD driver for R8A77970 V3M SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The capabilities have default values which doesn't reflect the reality
when it concerns the base clock and the mul value. Use a fixe rate
for the gck. 240 MHz is an arbitrary choice, it is a multiple of the
maximum SD clock frequency handle by the controller and it allows to
get a 400 kHz clock for the card initialisation.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Convert this driver to driver model.
This driver is also used by VEXPRESS platforms which doesn't
use driver model.
Tested on STM32F746 and STM32F769 platforms.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Update arm_pl180_mmci_init() prototype by adding struct mmc**
param. This is needed before converting this driver to driver model
in order to use arm_pl180_mmci_init() in driver model and in none
driver model implementation
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The following error has been observed on i.MX25 with a high-speed SDSC
card:
Data Write Failed in PIO Mode.
It was caused by the timeout set on PRSSTAT.BWEN, which was triggered
because this bit takes 15 ms to be set after writing the first block to
DATPORT with this card. Without this timeout, all the blocks are
properly written.
This timeout was implemented by decrementing a variable, so it was
depending on the CPU frequency. Fix this issue by setting this timeout
to a long enough absolute duration (500 ms).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
MMC commands like MMC_CMD_ALL_SEND_CID or MMC_CMD_SEND_CSD can reach
500 us. This patch increases the polling status register delay to avoid
a timeout on a command.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since e7881d85 "dm: mmc: Drop CONFIG_DM_MMC_OPS" DM_MMC_OPS
is no more used, remove it from STM32_SDMMC2 dependencies
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
The MMC framework in U-Boot does not support a systematic API for
timing switch like mmc_set_timing() in Linux.
U-Boot just provides a hook to change the clock frequency via
mmc_set_clock(). It is up to drivers if additional register
settings are needed.
This driver needs to set a correct timing mode into a register when
it migrates to a different speed mode. Only increasing clock frequency
could result in setup/hold timing violation.
The timing mode should be decided by checking MMC_TIMING_* like
drivers/mmc/host/sdhci-cadence.c in Linux, but "timing" is not
supported by U-Boot for now. Just use mmc->clock to decide the
timing mode.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add initial support for setting the vqmmc regulator. Since we do not
support 1V8 modes, set the regulator to 3V3 and enable it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Old version of the uniphier-sd 64bit IO support patchset V1 was
applied by the maintainer, update the uniphier-sd.c with the
changes from the V3 of the patchset.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds SD/MMC support for STM32H7 SoCs.
Here is an extraction of SDMMC main features, embedded in
STM32H7 SoCs.
The SD/MMC block include the following:
_ Full compliance with MultiMediaCard System Specification
Version 4.51. Card support for three different databus modes:
1-bit (default), 4-bit and 8-bit.
_ Full compatibility with previous versions of MultiMediaCards
(backward compatibility).
_ Full compliance with SD memory card specifications version 4.1.
(SDR104 SDMMC_CK speed limited to maximum allowed IO speed,
SPI mode and UHS-II mode not supported).
_ Full compliance with SDIO card specification version 4.0.
Card support for two different databus modes: 1-bit (default)
and 4-bit. (SDR104 SDMMC_CK speed limited to maximum allowed IO
speed, SPI mode and UHS-II mode not supported).
_ Data transfer up to 208 Mbyte/s for the 8 bit mode.
(depending maximum allowed IO speed).
_ Data and command output enable signals to control external
bidirectional drivers.
The current version of the SDMMC supports only one SD/SDIO/MMC card
at any one time and a stack of MMC Version 4.51 or previous.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the TI SOCs a PBIAS cell exists to provide a bias voltage to the MMC1
IO cells. Without this bias voltage these I/O cells can not function
properly. The PBIAS cell is controlled by software.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add OF match entries and quirks for Renesas RCar Gen3 controllers
into the driver. The IP this driver handles is in fact Matsushita
one and in used both in Socionext and Renesas chips.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Check if the OF match has any associated data and if so, use those
data as the controller quirks, otherwise fallback to the old method
of reading the controller version register to figure out the quirks.
This allows us to supply controller quirks on controllers which ie.
do not have version register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The Renesas RCar Gen3 contains the same controller, originally
Matsushita. This patch adds support for handling of the 64bit
FIFO on this controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The Renesas RCar Gen3 contains the same controller, originally
Matsushita, yet the register addresses are shifted by 1 to the
left. The whole controller is also 64bit, including the data
FIFOs and RSP registers. This patch adds support for handling
the register IO by shifting the register offset by 1 in the IO
accessor functions.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
This patch prepares the driver to support controller(s) with registers
at locations shifted by constant. Pull out the readl()/writel() from
the driver into separate functions, where the adjustment of the register
offset can be easily contained.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Use struct udevice* as input parameter. Previous
parameters are retrieved through plat and priv data.
This to prepare to use the reset framework.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
After Simon's patch, the dtoc can work with 64bit address,
so we need to fix reg number for it.
Depend on Simon's patch set:
https://patchwork.ozlabs.org/cover/807266/
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Update the Rockchip SDHCI wrapper to support a live device tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 2
- use the dev_read_addr_ptr function in rockchip_sdhci.c
Update the Rockchip-specific wrapper for the Designware driver to
support a live device tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 2
- use the dev_read_addr_ptr function in rockchip_dw_mmc.c
Import include/linux/dma-direction.h from Linux 4.13-rc7 and delete
duplicated definitions of enum dma_data_direction.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When enabling the new mmc timing mode, we inadvertently clear all the
remaining bits in the new timing mode register. The bits cleared
include a default phase delay on the output clock. The BSP kernel
states that the default values are supposed to be used. Clearing them
results in decreased performance or transfer errors on some boards.
Fixes: de9b1771c3 ("mmc: sunxi: Support new mode")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The driver-model rework changed, among other things, the way the private
data were moved around. It now uses the private field in the struct mmc.
However, the mmc_create argument was changed in the process to always pass
the array we used to have to store our private structures.
The basically means that all the MMC driver instances will now have the
private data of the first instance, which obviously doesn't work very well.
Pass the proper pointer to mmc_create.
Fixes: 034e226bc7 ("dm: mmc: sunxi: Pass private data around explicitly")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Almost all of the newer Allwinner SoCs have a new operating mode for the
eMMC clocks that needs to be enabled in both the clock and the MMC
controller.
Details about that mode are sparse, and the name itself (new mode vs old
mode) doesn't give much details, but it seems that the it changes the
sampling of the MMC clock. One side effect is also that it divides the
parent clock rate by 2.
Add support for it through a Kconfig option.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This changes pci_mmc driver to use PCI_CLASS_SYSTEM_SDHCI instead of
individual vendor id & device id pair to support generic PCI SD host
controller.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This patch allows to show the EXT_CSD[179] partition_config
register info, just by specifying the dev param:
U-Boot> mmc partconf 0
EXT_CSD[179], PARTITION_CONFIG:
BOOT_ACK: 0x0
BOOT_PARTITION_ENABLE: 0x0
PARTITION_ACCESS: 0x0
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
All boards which use DM_MMC have now been converted to use DM_MMC_OPS.
Drop the option and good riddance.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable driver model for MMC (including BLK), SATA and USB. Note that USB
does not yet work correctly since the nodes are disabled. Hopefully this
can be resolved by the maintainer.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to use fsl_esdhc_init() with driver model. Move the mmc_init() out
of this function so that we can use it for our common init.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model we want to store the mmc and configuration structure in
platform data. Set up structure up and use it for non-DM as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since esdhc_init_common() can fail it should return an error code. Update
this and also adjust the timeout mechanism to use get_timer(), which is a
more common approach.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since esdhc_reset() can fail it should return an error code. Update this
and also adjust the timeout mechanism to use get_timer(), which is a more
common approach.
Signed-off-by: Simon Glass <sjg@chromium.org>
Driver model wants to use the core functions in this file but accesses the
driver-private data in a different way. Move the code into new 'common'
functions and set up stubs to call these. Also sort the operations into
alphabetical order for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
