Half of this driver is a DM-based timer driver, and half is RISC-V-specific
IPI code. Move the timer portions in with the other timer drivers. The
KConfig is not moved, since it also enables IPIs. It could also be split
into two configs, but no boards use the timer but not the IPI atm, so I
haven't split it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
This is a regular timer driver, and should live with the other timer
drivers.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
Add support for the hardware pseudo random number generator found in Qualcomm SoC-s.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This adds the driver for the IPQ40xx built-in MDIO.
This will be needed to support future PHY driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for the Qualcomm QUP SPI controller that is commonly found in most of Qualcomm SoC-s.
Driver currently supports v1.1.1, v2.1.1 and v2.2.1 HW.
FIFO and Block modes are supported, no support for DMA mode is planned.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
- Fix stm32prog command: parsing of FlashLayout without partition
- Update MAINTAINERS for ARM STM STM32MP
- Manage eth1addr on dh board with KS8851
- Limit size of cacheable DDR in pre-reloc stage in stm32mp1
- Use mmc_of_parse() to read host capabilities in mmc:sdmmc2 driver
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl+QXvgACgkQ4rK92eCq
k3Vbrgf/cBKPY9bS+lJVARgjDvIOdcXzpgH/F7dUlq+dzu/mCwhIBVKxM7/nXh5p
RhfGET2fpMYY/41LkKza7AqOiGTXZG4pTmCGe1UHXrXeIPjinWG1LQjU/KOk6U4n
681P9BZfTUXrVgzLBIUY1KBFVyMaiYfVjxU3MnA1vqrubymFbf+IpUt3OIegUDCp
AjrTdj7sFEQ3nG/pgTyqFCwkl/MG53aB9MiaBBRxeGHYnDn0qzAEHSGqzSZZGhNl
1ubJDF3K7w6Pj3MzIeA80M5r0fJoTy/qWcNH31psOpyQaHJ9NbPGjFYE6AkDPV4l
27QN71AcRtCzlv1XQpblA98pa1bUYw==
=Bl3G
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201021' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Activate CMD_EXPORTENV/CMD_IMPORTENV/CMD_ELF for STM32MP15 defconfig
- Fix stm32prog command: parsing of FlashLayout without partition
- Update MAINTAINERS for ARM STM STM32MP
- Manage eth1addr on dh board with KS8851
- Limit size of cacheable DDR in pre-reloc stage in stm32mp1
- Use mmc_of_parse() to read host capabilities in mmc:sdmmc2 driver
Add the STM32MP1 RNG driver in the list of drivers supported by
the STMicroelectronics STM32MP15x series.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add files and directories regex "stm32" and "stm" in "ARM STM STM32MP"
platform to avoid missing files or drivers supported by the
STMicroelectronics series STM32MP15x.
This patch adds the rules already used in Linux kernel for
ARM/STM32 ARCHITECTURE.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add MediaTek USB3 Dual-Role controller driver to ARM MEDIATEK,
and add myself as a maintainer for it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Fully-Programmable Input/Output Array (FPIOA) device controls pin
multiplexing on the K210. The FPIOA can remap any supported function to any
multifunctional IO pin. It can also perform basic GPIO functions, such as
reading the current value of a pin. However, GPIO functionality remains
largely unimplemented (in favor of the dedicated GPIO peripherals).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This extends the pinctrl-sandbox driver to support pin muxing, and adds a
test for that behaviour. The test is done in C and not python (like the
existing tests for the pinctrl uclass) because it needs to call
pinctrl_select_state. Another option could be to add a command that
invokes pinctrl_select_state and then test everything in
test/py/tests/test_pinmux.py.
The pinctrl-sandbox driver now mimics the way that many pinmux devices
work. There are two groups of pins which are muxed together, as well as
four pins which are muxed individually. I have tried to test all normal
paths. However, very few error cases are explicitly checked for.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl960JkcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDaWCACYjvloDzXQaYaauWwR
whFwgkUAQ8yjadj/12We/X2b7HGisNFNE80e/V4MU8RrJDFZmohZdLWMfRKez29X
d+BG+OzVXxHWozny7ZQ2g1yYJbgCI7sVUeemQjUBZJ6aKPneQlVfwyfT2l88wOVK
yQMqS+ZyVogihR9/NHCOlJHog+6OOoBmc16w1tymM6QcO8ZsYeA66ed8SLnjDb3N
Rg2Ll2RR/lHuD/Fpxt1aUhybXFKSIOr4Qopo5X0hw5B3ibkp6JXGRE2wIwQYw6CA
q+sKTg37CSzylipkQ5EOGdLcXD7r3KIGkSbUMb8wvt6dROarnIuQ+zJeF3sr+l2H
hSoU
=vHqZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.01 cycle:
This feature set includes a new CPU driver for at91 family, new driver
for PIT64B hardware timer, support for new at91 family SoC named sama7g5
which adds: clock support, including conversion of the clock tree to
CCF; SoC support in mach-at91, pinctrl and mmc drivers update. The
feature set also includes updates for mmc driver and some other minor
fixes and features regarding building without the old Atmel PIT and the
possibility to read a secondary MAC address from a second i2c EEPROM.
Add a driver to setup the USB PHY-s on Qualcomm IPQ40xx series SoCs.
The driver sets up HS and SS phys.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
On Qualcomm IPQ40xx SoC series, GCC clock IP also handles the resets.
So since this will be needed by further drivers, lets add a driver for the reset controller.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
I also followed the development of the SquashFS support in U-Boot
as part of Joao Marcos internship, so I would also appreciate receiving
new contributions and bug reports related to this topic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
As I have followed the development of the SquashFS support in U-Boot
as part of Joao Marcos work, it makes sense to get Cc'ed on
contributions/bug reports related to the squashfs support.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Import Qualcomm IPQ4019 GCC bindings from Linux.
This will enable using bindings instead of raw clock numbers both in the driver and DTS like Linux does.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Update MAINTAINERS file for new files.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since the current code base is mostly from btrfs-progs, anyone
contributing to U-Boot btrfs code could also help us to improve
btrfs-progs and btrfs kernel module.
Also add myself as designated reviewer.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Add Cortina Access LED controller support for CAxxxx SOCs
Signed-off-by: Jway Lin <jway.lin@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Simon Glass <sjg@chromium.org>
Add head file fixed link error and remove unused flashing function
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Python scripts to test 'ls' and 'load' commands. The scripts
generate a SquashFS image and clean the directory after the assertions,
or if an exception is raised.
Signed-off-by: Joao Marcos Costa <joaomarcos.costa@bootlin.com>
Add support for SquashFS filesystem. Right now, it does not support
compression but support for zlib will be added in a follow-up commit.
Signed-off-by: Joao Marcos Costa <joaomarcos.costa@bootlin.com>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- Configuration changed, mainly several "CONFIG_..." moved from
s5p4418_nanopi2.h to s5p4418_nanopi2_defconfig and USB related
configs removed because USB is not supported yet.
- s5p4418_nanopi2.h: "CONFIG_" removed from several s5p4418/nanopi2
specific defines because the appropriate values do not need to be
configurable.
- pinctrl is supported now, therefore "CONFIG_PINCTRL=y" added to
s5p4418_nanopi2_defconfig.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
This introduces initial support for the popular Qualcomm
IPQ40x8 and IPQ40x9 WiSoC series.
IPQ40xx series have 4x Cortex A7 ARM-v7A cores.
Supported are: IPQ4018, IPQ4019, IPQ4028 and IPQ4029.
IPQ40x8 and IPQ40x9 use the same cores, but differ in
addressable RAM size (1GB for IPQ40x9 and 256MB for IPQ40x8)
and supported peripherals (IPQ40x8 lacks RGMII, LCD controller
and EMMC/SDHCI controllers).
IQP4028/IPQ4029 models differ from IPQ4018/IPQ4019 only
by their rated temperatures rates with IPQ402X models being
rated for wider temperature ranges.
Initially this supports:
* Simple clock driver (Only for UART1 now, will be extended)
* Pinctrl driver (Supports UARTX and GPIO now, will be extended)
* GPIOs already supported by msm_gpio driver with updates
* UARTs already supported by serial_msm driver with updates
Further peripherals will come in later patches.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
According to Server Base System Architecture (SBSA) specification,
the SBSA Generic Watchdog has two stage timeouts: the first signal
(WS0) is for alerting the system by interrupt, the second one (WS1) is a
real hardware reset.
More details about the hardware specification of this device:
ARM DEN0029B - Server Base System Architecture (SBSA)
This driver can operate ARM SBSA Generic Watchdog as a single stage
In the single stage mode, when the timeout is reached, your system
will be reset by WS1. The first signal (WS0) is ignored.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds very basic support for the Octeon III SoCs. Only
CFI parallel NOR flash and UART is supported for now.
Please note that the basic Octeon port does not include the DDR3/4
initialization yet. This will be added in some follow-up patches
later. To still use U-Boot on with this port, the L2 cache (4MiB on
Octeon III CN73xx) is used as RAM. This way, U-Boot can boot to the
prompt on such boards.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This series comprises error corrections for the UEFI subsystem:
* correct consideration of timestamps for variable authentication
* correct collection of data regions for code authentication
* correct unit tests to test loading dbx
* enable FAT_WRITE as required by the UEFI spec
The boot manager uses log functions instead of printf() and debug().
The UEFI intialization state is exported.
-----BEGIN PGP SIGNATURE-----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=wwI2
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi into next
Pull request for UEFI sub-system for efi-2020-10-rc1
This series comprises error corrections for the UEFI subsystem:
* correct consideration of timestamps for variable authentication
* correct collection of data regions for code authentication
* correct unit tests to test loading dbx
* enable FAT_WRITE as required by the UEFI spec
The boot manager uses log functions instead of printf() and debug().
The UEFI intialization state is exported.
Due to the large number of clocks, I decided to use the CCF. The overall
structure is modeled after the imx code. Clocks parameters are stored in
several arrays, and are then instantiated at run-time. There are some
translation macros (FOOIFY()) which allow for more dense packing.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
CC: Lukasz Majewski <lukma@denx.de>
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
=2Yuu
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.10
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
Add the recently added reStructuredText board documentation in the
appropriate MAINTAINERS files.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Convert README.log to reStructuredText and add it to the generated HTML
documentation.
Assign doc/develop/logging.rst to the maintainer of LOGGING.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
While in here, add the doc file to the MAINTAINERS entry.
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Amit Singh Tomar <amittomer25@gmail.com>
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
While in here, add the doc file to the MAINTAINERS entry for coldfire.
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Tom Rini <trini@konsulko.com>
include/dfu.h and doc/api/dfu.rst belong to the device firmware update
sub-system. So let's add them to DFU in MAINTAINERS.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
The documentation should rest with the same maintainer as the code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add myself as maintainer for the OP-TEE related UEFI variable storage.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add dt-binding files of xhci-mtk and phys, C files of
phys.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
This commit adds common arch support for Actions Semi Owl
series SoCs and removes the Bubblegum96 board files.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
- Fix boot on am335x guardian board
- Increase OPSI speed on AM65x and J721E devices
- Use JTAD register for identifying K3 devices.
- Update TI entry in MAINTAINERS file.
If CONFIG_LOG=n, we still expect output for log_err(), log_warning(),
log_notice(), log_info() and in case of DEBUG=1 also for log_debug().
Provide unit tests verifying this.
The tests depend on:
CONFIG_CONSOLE_RECORD=y
CONFIG_LOG=n
CONFIG_UT_LOG=y
It may be necessary to increase the value of CONFIG_SYS_MALLOC_F_LEN to
accommodate CONFIG_CONSOLE_RECORD=y.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide a log driver that broadcasts RFC 3164 messages to syslog servers.
rsyslog is one implementation of such a server.
The messages are sent to the local broadcast address 255.255.255.255 on
port 514.
The environment variable log_hostname can be used to provide the HOSTNAME
field for the messages. The optional TIMESTAMP field of RFC 3164 is not
provided.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add all TI specific drivers, include, arch files under ARM TI entry.
Driver files are added only if there is no entry for the specific
subsystem in MAINTAINERS file.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for Xilinx window watchdog, which can be found on
Versal platforms.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Initial DesignWare based DM support for Cortina Access CAxxxx SoCs.
Signed-off-by: Arthur Li <arthur.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Change plain test README to rst format and move this file
in documentation directory.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Assign Alex Nemirovsky as custodian for all
Cortina Access (CA) for ARM and MIPS based SoCs.
Currently Cortina Access CAxxxx family of SoCs support both
ARM and MIPS ISA. Drivers have cross platform support for
both architectures.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Convert Android documentation from regular txt format to Sphinx (RST).
Also add Android index.rst file and reference it in root index.rst, so
that Android documentation is visible.
Test:
$ make htmldocs
$ xdg-open doc/output/index.html
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Take up maintainership of random number generator drivers with
Heinrich Schuchardt as the reviewer.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add myself as maintainer for ST-Ericsson U8500 SoC to MAINTAINERS.
Linus Walleij usually reviews all Ux500 related patches,
so add him as a reviewer.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Take over TI maintainership from Tom.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add new defconfig files for the J721e High Security EVM.
These defconfigs are the same as for the non-secure part, except for:
CONFIG_TI_SECURE_DEVICE option set to 'y'
CONFIG_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_SPL_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_BOOTCOMMAND uses FIT images for booting
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Sam doesn't work for Linaro anymore, so Linaro mail is not valid. Change
it to his home mail instead.
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
The bcm283x has grown in files, which was not reflected in the
MAINTAINERS file. Fix this by adding the missing entries.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This adds platform code and the device tree for the Phytium Durian Board.
The initial support comprises the UART and the PCIE.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Steven Hao <liuhao@phytium.com.cn>
add DM based PCI Configuration space access support for
MPC85xx PCI Bridge. This driver is based on
arch/powerpc/cpu/mpc85xx/pci.c
In the old driver there is a fix for a hw issue on the
TARGET_MPC8555CDS and TARGET_MPC8541CDS boards. As I
have no such hardware I did not port this part.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdspnqAAoJEB6zHgIOrC/Ixi4IAJEEiCZPu6Z3fbkFX/Um7vCX
eMTltJN8nz4oiSi3xdx3ejueqWdW3F8VuCkHb0j0bVAhMlUlVgwCzfd0cD+D2iwS
jkrgzASNAr+JeYKYEdWqqfaUxOCd2qfuBu9EXlpvKQLWLt+KRfsOsHWcgR4bf095
aGCihvd/fKhKYUvbf5cEQnsWa3UwtsKk4Web5MKjxXx3p0iVNlu4KLd/vDWfTios
X1NqiO5ZjXNrDxyG6Aj8lgDXlE5kfeKaN/aCJU1/0U2cXm8JRu2w2dv1P/e/kU+j
NHIGzICAG4Lk/4gQTeuohJxLyvj7K3i1H12ik9Qeh4H1/5fsyybyltGUo7H443s=
=JYe3
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2020.01 cycle
This feature set includes Eugen's work on a new tiny flexcom driver and
eeprom mac retrieval for the sam9x60-ek board.
The xhci.h header file is currently located under drivers/usb/xhci
Move it to the include/usb folder to make it available to drivers that
are not under drivers/usb/xhci
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add Support for UFS Host Controller Interface (UFSHCI) for communicating
with Universal Flash Storage (UFS) devices. The steps to initialize the
host controller interface are the following:
- Initiate the Host Controller Initialization process by writing to the
Host controller enable register.
- Configure the Host Controller base address registers by allocating a
host memory space and related data structures.
- Unipro link startup procedure
- Check for connected device
- Configure UFS host controller to process requests
Also register this host controller as a SCSI host controller.
Taken from Linux Kernel v5.2 (drivers/scsi/ufs/ufshcd.c) and ported to
U-boot.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Move android generic config and boot sequence in meson64_android header
and fix size of userdata to use all eMMC on SEI510.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Fully take over the ARM maintainers entry.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
New firmware header to place firmware specific macro and function
declarations. The patch also moves the macros defining PM operations as
well as some helper macros.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP mailbox driver implementing IPI communication with PMU. This would
allow U-Boot SPL to communicate with PMUFW to request privileged
operations.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add simple ZynqMP firmware drive to populate child nodes under
zynqmp_firmware DT node.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This updates MAINTAINERS and git-mailrc to add me as maintainer for
socfpga.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
1. Add myself as Android A/B and AVB maintainer
2. Add Sam Protsenko as Designated reviewer for A/B
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Add MAINTAINERS entry for HI3660 SoC by adding the arch includes.
While doing so, adding myself as the co-maintainer for HISILICON
SoCs since I'm planning to maintain HI3660 SoC separately and considering
doing improvements to the existing HiSilicon SoC architecture.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Change the UEFI documentation to Sphinx style and integrate it into the
rest of the Sphinx generated documentation.
Remove the inaccurate TODO list in doc/uefi/uefi.rst.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Since u-boot has added the spi-mem framework and replaced
the spi-nor framework, the mtk_qspi is no longer compatible
with the new spi-nor driver.
Remove this driver along with replacing config item
with new mtk spi-nor driver.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
[jagan: squash related changes and update commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Commit 32ce6179fb ("optee: Add lib entries for sharing OPTEE code across
ports") adds code into lib/optee but neglects to update MAINTAINERS to make
me buggable for questions and maintenance.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Suggested-by: Jens Wiklander <jens.wiklander@linaro.org>
Macpaul have left Andestech for a while, and this mail address
macpaul@andestech.com can not received mail anymore.
It might encounter account creation problem in this switching
to gitlab about nds32 tree.
So change the nds32 maintainer as Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
include/net.h currently has no maintainer.
Assign include/net.h to the maintainer of the NET subsystem.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Introduce new UCLASS_PCI_EP class for handling PCI endpoint
devices, allowing to set various attributes of the PCI endpoint
device, such as:
* configuration space header
* BAR definitions
* outband memory mapping
* start/stop PCI link
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit ad7061ed74 ("doc: Move device tree bindings documentation to
doc/device-tree-bindings") moved all device tree binding documentation
to doc/device-tree-bindings directory.
The current U-Boot project still have two documentation directories:
- doc/
- Documentation/
Move all documentation and sphinx files to doc directory so all content
can be in a common place.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Add myself as an SH maintainer.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>
Christophe will not have maintainer activities, so remove its name.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Cc: Christophe Kerello <christophe.kerello@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Change my email address, too many mails
gets to my private mail, created specific email
account just for developmement.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2C9f
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20190606' of https://github.com/pchotard/u-boot
- Add Ethernet support for STM32MP1
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
Add imx dts files to the MAINTAINERS file list, so that i.MX
devicetree related patches can be properly sent to the i.MX folks.
Reported-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
sp805 is watchdog on some NXP layerscape SoCs, adding
it's driver. Configs CONFIG_WDT_SP805, CONFIG_WDT, CONFIG_CMD_WDT
needs to be enabled to use it.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Assign include/charset.h to EFI PAYLOAD.
The functions defined in this include are used by the UEFI sub-system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Ocelot
- mt7620: rename arch to more generic name mtmips
- mips: pass initrd addresses via DT as physical addresses
-----BEGIN PGP SIGNATURE-----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=SZ/W
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-05-03' of git://git.denx.de/u-boot-mips
- mscc: small fixes, enhance network support for Serval, Luton and Ocelot
- mt7620: rename arch to more generic name mtmips
- mips: pass initrd addresses via DT as physical addresses
Update the mmc maintainer from Jaehoon to me.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Marek Vasut <marex@denx.de>
This updates MAINTAINERS and git-mailrc to add me as a
co-custodian for rockchip
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Tom Rini <trini@konsulko.com>
Add new defconfig files for the AM65x High Security EVM.
This defconfigs are the same as for the non-secure part, except for:
CONFIG_TI_SECURE_DEVICE option set to 'y'
CONFIG_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_SPL_FIT_IMAGE_POST_PROCESS option set to 'y'
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
K3 HS devices require signed binaries for boot, use the SECDEV tools
to sign the boot artifacts during build.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
K3 devices have High Security (HS) variants along with the non-HS already
supported. Like the previous generation devices (OMAP/Keystone2) K3
supports boot chain-of-trust by authenticating and optionally decrypting
images as they are unpacked from FIT images. Add support for this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
This updates MAINTAINERS and git-mailrc to add me as a
co-custodian for socfpga.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
In order to support the Amlogic G12A clock controller,
re-architect the clock files into a meson directory.
No functionnal changes.
MAINTAINERS entry is also updated.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The 'exception' command allows to test exception handling.
This implementation supports ARM, x86, RISC-V and the following exceptions:
* 'breakpoint' - prefetch abort exception (ARM 32bit only)
* 'unaligned' - data abort exception (ARM only)
* 'undefined' - undefined instruction exception
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add the DM_MMC-compatible DesignWare MMC driver support for Synopsys
ARC devboards. It is created to switch ARC devboards to use DM_MMC.
It required information such as clocks (Bus Interface Unit clock,
Card Interface Unit clock) and SDIO bus width.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Alignment with kernel driver name & binding
introduced by https://patchwork.kernel.org/cover/10761943/
to use the final marketing name = STPMIC1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Missed few mails from openedev, since most of the day I look at
amarulasolutions mail so update the same.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch does the following changes to the u-boot-marvell maintainers
entry:
- Add Armada-7k/8k to the list
- Remove Prafulla and Luka since they have been silent on the list for
a long time. Please speak up, if you would like to continue or better
start maintaining.
- Add multiple Marvell / MVEBU related driver directories and files
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
The MAINTAINERS file was copied from Linux Kernel along with all its
statuses of maintainership. However tools/genboardscfg.py accepts only
Maintained, Supported and Orphan. Remove then the Odd Fixes and
Obsolete from MAINTAINERS file to avoid confusion.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Currently, there is no easy way to add or modify UEFI variables.
In particular, bootmgr supports BootOrder/BootXXXX variables, it is
quite hard to define them as u-boot variables because they are represented
in a complicated and encoded format.
The new command, efidebug, helps address these issues and give us
more friendly interfaces:
* efidebug boot add: add BootXXXX variable
* efidebug boot rm: remove BootXXXX variable
* efidebug boot dump: display all BootXXXX variables
* efidebug boot next: set BootNext variable
* efidebug boot order: set/display a boot order (BootOrder)
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
"env [print|set] -e" allows for handling uefi variables without
knowing details about mapping to corresponding u-boot variables.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich is going to take over maintainership of the efi_loader tree
going forward.
To ensure that I will still receive review mails at least, add me as
reviewer with a stable email address.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Matthias Brugger agreed to take over maintainership from me for the
Raspberry Pi tree. Add him to the MAINTAINERS file instead.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a new defconfig file for the AM57xx High Security EVM. This config
is specific for the case of USB/UART booting.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a new defconfig file for the DRA7xx High Security EVM. This config
is specific for the case of USB booting.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add myself as co-maintainer for U-Boot SPI NOR subsystem.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: drop mtd/spi file from SPI entry]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Change maintainers to Prabhakar Kushwaha for fsl-qoriq, mpc85xx
and mpc86xx.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Move file ocelot_switch to mscc_eswitch to prepare to add
new net drivers for other MSCC SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Handle correctly directory arch/arm/mach-stm32mp/ :
Add a trailing slash to include all files
and subdirectory files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.
Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.
Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f24036)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for the Microsemi Ethernet switch present on
Ocelot SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add myself as the maintainer of CZ.NIC's Turris Omnia and Turris Mox
projects.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The Jaguar2 SOC family has 63 gpio pins therefore I extended mscc-common
to support new numbe of pins and remove any platform dependency from
mscc-common.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
This patch add a new SPI driver for MSCC SOCs that does not sport the
designware SPI hardware controller.
Performance gain: 7.664 seconds vs. 17.633 for 1 Mbyte write.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This add support for the the MSCC serial GPIO driver in MSCC
VCoreIII-based SOCs.
By using a serial interface, the SIO controller significantly extends
the number of available GPIOs with a minimum number of additional pins
on the device. The primary purpose of the SIO controller is to connect
control signals from SFP modules and to act as an LED controller.
This adds the base driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Add initial support for the Ingenic JZ47xx MIPS SoC.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Adding the support for the Luton boards PCB91 which share common code with
the Ocelots boards, including board code, device tree and configuration.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This family of SoCs are found in the Microsemi Switches solution and have
already a support in the linux kernel.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The motivation for this is to allow distributions to distribute all
possible tools in a generic way, avoiding the need of specific tools
building for each machine.
Especially on OpenEmbedded / Yocto Project ecosystem, it is very
common each BSP to end providing their specific tools when they need
to generate images for some SoC (e.g MX23 / MX28 in meta-freescale
case).
Using this, we can package the tools doing:
$: make tools-only_defconfig
$: make tools-only
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
[trini: Add MAINTAINERS entry for myself, add to .travis.yml, make
U-Boot itself buildable to not trip up other frameworks]
Signed-off-by: Tom Rini <trini@konsulko.com>
Alex suggested to add me as a reviewer for the EFI subsystem.
The patch also adds a description for R: entries.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Xilinx is introducing Versal, an adaptive compute acceleration platform
(ACAP), built on 7nm FinFET process technology. Versal ACAPs combine
Scalar Processing Engines, Adaptable Hardware Engines, and Intelligent
Engines with leading-edge memory and interfacing technologies to deliver
powerful heterogeneous acceleration for any application. The Versal AI
Core series has five devices, offering 128 to 400 AI Engines. The series
includes dual-core Arm Cortex™-A72 application processors, dual-core Arm
Cortex-R5 real-time processors, 256KB of on-chip memory with ECC, more
than 1,900 DSP engines optimized for high-precision floating point with
low latency.
The patch is adding necessary infrastructure in place without enabling
platform which is done in separate patch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
accidentially while fixing merge errors for patch:
https://lists.denx.de/pipermail/u-boot/2018-September/342278.html
missed to add files:
MAINTAINERS
drivers/i2c/Kconfig
drivers/i2c/Makefile
add them with this patch.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Adds configuration option OPTEE_TA_AVB and a header file describing the
interface to the Android Verified Boot 2.0 (AVB) trusted application
provided by OP-TEE.
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds a uclass to interface with a TEE (Trusted Execution Environment).
A TEE driver is a driver that interfaces with a trusted OS running in
some secure environment, for example, TrustZone on ARM cpus, or a
separate secure co-processor etc.
The TEE subsystem can serve a TEE driver for a Global Platform compliant
TEE, but it's not limited to only Global Platform TEEs.
The over all design is based on the TEE subsystem in the Linux kernel,
tailored for U-Boot.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Add support for the Arm Versatile Express config bus that is
being used for exposing various subsystems via a generic
configuration bus. This driver adds support for generating
transactions on this configuration bus and can be used by
other drivers to abstract the communication with the actual
function providers.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This is the PR for SPI-NAND changes along with few spi changes.
[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a PHY driver for the Qualcomm dragonboard 410c which
allows switching on/off and resetting the phy connected
to the EHCI controllers and USBHS controller.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Add support for Arm Mali Display Processors DP500, DP550 and DP650.
Only one layer is being used to display the console or boot logo,
even if more layers are supported in the hardware.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
The include/video*.h files are part of the drivers in drivers/video. So it
makes sense to assign them to the same maintainer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch implements the EFI_UNICODE_COLLATION_PROTOCOL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch provides a define to initialize a table that maps lower to
capital letters for Unicode code point 0x0000 - 0xffff.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- Multiples updates to the turris boards / platform
- Changes / enhancements to the Marvell PHY drivers, mainly
to support the turris platform
- Many fixes and enhancements to the pxa3xx NAND driver
- Fixes for the UART boot mode in kwboot
- Misc minor changes to other 32bit and 64bit boards
