Up now only MX5 and MX6 can share code, because they have
a common source directory in cpu/armv7. Other not armv7
i.MX can profit of the same shared code. Move these files
into a directory accessible for all, similar to plat-mxc
in linux.
Signed-off-by: Stefano Babic <sbabic@denx.de>
A device tree is used to configure the NAND, including memory
timings and block/pages sizes.
If this node is not present or is disabled, then NAND will not
be initialized.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a NAND controller along with a bindings file for review.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add selection of NAND flash pins to the funcmux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Define default SoC input clock frequencies for i.MX31 in order to get rid of
duplicated definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Helmut Raiger <helmut.raiger@hale.at>
The MFN bit-field of the PLL registers represents a signed value. See the
reference manual.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Switch the mx35 timer driver to the 32-kHz clock source to avoid calling
mxc_get_clock() again and again, and to be consistent with the timer drivers of
other i.MX SoCs.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Define default SoC input clock frequencies for i.MX35 in order to get rid of
duplicated definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
The clock dividers that were used do not match at all the reference manual. They
were either completely broken, or came from an early silicon revision
incompatible with the current one.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
The MFN bit-field of the PLL registers represents a signed value. See the
reference manual.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Useless code is removed, and get buswidth value.
buswidth value will be used to choice the 4bit or 8bit.
(Now used 4bit mode in sdhci.c by default)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We have the timer code in arch/arm/cpu/armv7/omap-common/timer.c that
has been configuring and enabling the timer, so remove our code that
does the same thing by different methods.
Tested on EVM GP, SK-EVM and Beaglebone.
Signed-off-by: Tom Rini <trini@ti.com>
AM/DM37x SoCs add the CTRL_WKUP_CTRL register. It contains the
GPIO_IO_PWRDNZ bit, which is required to be set to enable the I/O pads
of gpio_126, gpio_127 and gpio_129.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Cc: Tom Rini <trini@ti.com>
The board_postclk_init() function can be used to perform operations
that requires a working timer early within the U-Boot init_sequence.
Signed-off-by: Markus Hubig <mhubig@imko.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Use proper struct-based access for this register in the SPL code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The computation was not correct with low clock values: setting a 1MHz
clock would result in an overlap that would then configure a 25Mhz
clock.
This patch implements a correct computation method according to the
kirkwood functionnal spec. table 600 (Serial Memory Interface
Configuration Register).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Orion5x did not actually write GPIO output values
or input polarities, and ED Mini V2 had bad or
missing values for GPIO settings.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
* 'master' of git://git.denx.de/u-boot-usb:
MUSB driver: Timeout is never detected as the while loop does not end
usb: fix ulpi_set_vbus prototype
pxa25x: Add UDC registers definitions
USB: Fix strict aliasing in ohci-hcd
usb: Optimize USB storage read/write
ehci: Optimize qTD allocations
usb_stor_BBB_transport: Do not delay when not required
usb_storage: Remove EHCI constraints
usb_storage: Restore non-EHCI support
ehci-hcd: Boost transfer speed
ehci: cosmetic: Define used constants
ehci: Fail for multi-transaction interrupt transfers
arm:trats: Enable g_dnl composite USB gadget with embedded DFU function on TRATS
arm:trats: Support for USB UDC driver at TRATS board.
dfu:cmd: Support for DFU u-boot command
dfu: MMC specific routines for DFU operation
dfu: DFU backend implementation
dfu:usb: DFU USB function (f_dfu) support for g_dnl composite gadget
dfu:usb: Support for g_dnl composite download gadget.
ehci: cosmetic: Define the number of qt_buffers
Signed-off-by: Wolfgang Denk <wd@denx.de>
Define ARCH_MXC for i.MX devices. This is useful to identify features or
behaviors common to all i.MX SoCs.
The i.MX28 is omitted because its architecture is a bit different (like imx/mxc
vs. mxs in Linux).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kim Phillips <kim.phillips@freescale.com>
For representing a timeout value, it makes more sense to pass it as
'unsigned int'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Allow usage of the imx-common/iomux-v3.h framework by including pad settings
for the i.MX51. The content of the file is taken from Linux kernel at
commit 5d23b39 plus the required changes to make it work in U-Boot.
The contained pad settings are the minimum required to make an Efika MX boot
and get all the currently-implemented peripherals working in U-Boot.
It is recommended that this file not be just a dumping ground for pins but
only contain the settings required for all the boards using it.
Changes for v2:
* reference commit id from Linux kernel
* additionally roll in the USB pads
* removed GPIO_NUMBER define
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The DRAM initialization, after SPL has complete, is exactly the same
for all mxs SoCs so we should name it accordinly.
The following boards has been changed:
* apx4devkit
* m28evk
* mx28evk
* sc_sps_1
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
The internal Ethernet controller is only available on i.MX28
processors so it needs to use CONFIG_MX28 guardian to avoid having
this code called in others.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
The imx_decode_pll() function does not exist for mx5, so remove its declaration.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Each i.MX has its own gpio.h, defining the same structure.
The internal GPIO controller has the same layout
(at least for the register used by u-boot) and can be shared.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Tested-by: Matt Sealey <matt@genesi-usa.com>
commit d92591a (mxs: Convert sys_proto.h prefixes to 'mxs') introduced
a mxs_dram_init() function, which is not used anywhere.
Fix it, so that the following warning goes away:
mx28evk.c: In function ‘dram_init’:
mx28evk.c:67:2: warning: implicit declaration of function ‘mx28_dram_init’ [-Wimplicit-function-declaration]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
The elftosb call needs to use a target param specific for i.MX28. This
patch allow for later addition of i.MX233.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
Add cpu_mmc_init() function to make it easy to init a single eSDHC instance.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Do not pretend to have initialized mmc successfully if CONFIG_FSL_ESDHC is not
defined. Instead, only implement a custom cpu_mmc_init() when it does something.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
This is useful for forcing the ROM's
usb downloader to activate upon a watchdog reset.
Or, you can boot from either SD Card.
Currently, support added for MX53 and MX6Q
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Note: MX53 support untested.
Acked-by: Stefano Babic <sbabic@denx.de>
Round up tick_to_time() value instead of truncating it. This avoids stopping
waits instantly for low usec values, and this generally guarantees that the code
always waits for at least the requested duration.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Now that the main i.MX features work fine with dcache enabled, enabled it by
default if CONFIG_SYS_DCACHE_OFF is not defined.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Now that the main i.MX features work fine with dcache enabled, enabled it by
default if CONFIG_SYS_DCACHE_OFF is not defined.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Move some function calls to a more appropriate place, so they're
called only when needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The SPL doesn't need the CP15 reconfiguration, as that's what the
BootROM does for us already. Moreover, when the CP15 is reconfigured
and the code returns control to BootROM, the USB boot works no more.
Remove the code and allow [1] to work properly as well.
[1] http://git.bfuser.eu/?p=marex/mxsldr.git;a=summary
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The sys_proto.h functions (except the boot modes) are compatible with
i.MX233 and i.MX28 so we use 'mxs' prefix for its methods.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The iomux header is included on sys_proto.h so to avoid SoC specific
header inclusion.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
This patch enables the L1 data cache for systems based on Samsung
Exynos processor.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch support exynos pwm backlight driver. It can control backlight
power and brightness by using pwm.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
If dp_enabled was set, exynos fb driver support display port feature.
This patch depends on [PATCH] video: support exynos fimd driver
for various exynos series.
http://marc.info/?l=u-boot&m=134119605104467&w=2
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch set supports exynos display port drivers.
DisplayPort is an industry standard device to accommodate the increasing board
adoption of digital display technology within the PC and consumer electronics.
The interface supports internal chip-to-chip and external box-to-box digital
display connections.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch add display port base address for EXYNOS5. In case of EXYNOS4,
use DEVICE_NOT_AVAILABLE macro because DP is not supported.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch support display port phy control function.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch supports display block system regisger control.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch support exynos5 lcd clock control.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch supports exynos fimd driver for various exynos series different from
existing it supports only exynos4 chip.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Removed [-Wuninitialized] warning message.
The fout_sel is assigned to "-1" by default.
And start, gpio_func is initialized to 0.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In general, The get_timer_masked function get the system time,
no the number of ticks. Such as the nand_wait_ready will use
get_timer_masked to delay the operations. And change the system
time to adopt to the CONFIG_SYS_HZ.
Signed-off-by: Hongbo Zhong <bocui107@gmail.com>
Tested-by: Jaehoon Chung<jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch modifies the pinmux settings of MMC and UART as per
Exynos5250 Rev 1.0.
It also corrects the gpio offset calculations.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds support for BPLL clock.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
MPLL clock-out of Exynos5250 Rev 1.0 is always at 1.6GHz.
Adjust the divisor value to get 800MHz as needed by devices
like UART etc
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The patch adds the memory initialization sequence of DDR3.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add a structure for table-driven configuration mechanism such that no recompilation
is needed to update the configuration parameters, rather than hard-coding
board initialization parameters.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
save_boot_params_default() in cpu.c accesses uninitialized stack area
when it compiled with -O0 (not optimized).
This patch removes save_boot_params_default() and put the equivalent in start.S
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Acked-by: Tom Rini <trini@ti.com>
These flags were necessary when building tegra20 as a single binary
that supported ARM7TDMI and Cortex A9. Now that the ARM7TDMI support
is split into a separate SPL, this is no longer necessary.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable the building of private libgcc for SPL
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add SPL options to tegra20 config files and enable SPL build for
tegra20 boards. Also remove redundant code from u-boot that is not
contained in SPL.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move warmboot_save_sdram_params() to later in the boot sequence. This
code relies on devicetree to get the address of the memory controller
and with upcoming changes for SPL boot it gets called early in the
boot process when devicetree is not initialized yet.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for tegra20 arm7 boot processor. This processor is used
to power on the Cortex A9 and transfer control to it. In tegra this
processor is an ARM7TDMI not an ARM720T, but since we don't use cache
it was easier to just reuse the ARM720T code as the processors are
otherwise identical except for cache and MMU.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Take a few SPL fixes from armv7 and apply them to arm720t:
-Use dummy exception handlers for SPL build
-Initialize relocation register r9 to 0 for the case of no relocation
-ifdef out interrupt handler code
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In preparation for splitting out the armv4t code from tegra20, move
the tegra20 SoC code to arch/arm/cpu/tegra20-common. This code will
be compiled armv4t for the arm7tdmi and armv7 for the cortex A9.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is make naming consistent with the kernel and devicetree and in
preparation of pulling out the common tegra20 code.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This SoC is used in the Raspberry Pi, for example.
For more details, see:
http://www.broadcom.com/products/BCM2835http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf.
Initial support is enough to boot to a serial console, execute a minimal
set of U-Boot commands, download data over a serial port, and boot a
Linux kernel. No storage or network drivers are implemented.
GPIO driver originally by Vikram Narayanan <vikram186@gmail.com>
with many fixes from myself.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Note that this affects all users of the ARM1176 CPU that enable
CONFIG_ARCH_CPU_INIT, not just the BCM2835 SoC, potentially such as
tnetv107x.
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Following ARM's reference manuel for initializing the cache - the
kernel won't boot otherwise.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Some CPU (i.e u8500) need more cache management before launching
the Linux kernel.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Register mapping has changed on power control chip between
the first and second revision.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Tom Rini <trini@ti.com>
Functions such as providing power to the MMC device and reading
the processor version register should be in the cpu area for
access by multiple u8500-based boards.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Tom Rini <trini@ti.com>
LAN and GBF need to be powered explicitely, doing so with
interface to AB8500 companion chip.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Addresses between ux500.v1 and ux500.v2 have changed slightly,
hence mandating a review of the PRCMU access methods.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Enabling timers and clocks in PRCMU and cleaning up mailbox.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
This is to allow the prcmu functions to be used by multiple
u8500-based processors.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
We can safely use the same reset code written in C for both Davinci and
C6X platforms. In addition the C version of the code is marginally
smaller on Davinci.
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch updates secure_emif_sdram_config with the
same value written to sdram_config during ddr3 initialization.
During suspend/resume, this value is copied into sdram_config.
With this, a write to sdram_config at the end of resume sequence
which triggers an init sequence can be avoided.
Without this register write in place, the DDR_RESET line goes
low for a few cycles during resume which is a violation of the
JEDEC spec.
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
Also enable the ohci port on hawkboard. These additions result in an
increased u-boot size -- adjust the same accordingly in the board's
config.
Move the usb header for da8xx platforms under arch-davinci.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Make sure that when we setup the stack before calling s_init() we have
the stack have 8-byte alignment for ABI compliance.
Tested-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Rini <trini@ti.com>
Make the lowlevel_init function that these platforms have which just
sets up the stack and calls a C function available to all armv7
platforms. As part of this we change some of the macros that are used
to be more clear. Previously (except for am335x evm) we had been
setting CONFIG_SYS_INIT_SP_ADDR to a series of new defines that are
equivalent to simply referencing NON_SECURE_SRAM_END. On am335x evm we
should have been doing this initially and do now.
Cc: Sricharan R <r.sricharan@ti.com>
Tested-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Rini <trini@ti.com>
- Correct the MMC1 base offset
- Remove MMC2 (that area is reserved and not MMC2).
- Add the real BOOT_DEVICE_MMC2 value
Signed-off-by: Tom Rini <trini@ti.com>
This gets us rid of duplication of the same file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
If VDDIO has a brownout, then the VDD5V_GT_VDDIO becomes unreliable
but this wasn't clear on code so a comment has been added to clarify
it.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
As the register accessing mode is the same for all i.MXS SoCs we ought
to use 'mxs' prefix intead of 'mx28'.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Most code can be shared between i.MX23 and i.MX28 as both are from
i.MXS family; this source directory structure makes easy to share code
among them.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
The mx28 prefix has been added to the initialization data and function
so it is clear by which SoC it is used as i.MX233 will have a specific
one. While on that, we also change it to static.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
The information now is gathered from HW_DIGCTL_CHIPID register and
includes the chip modem and revision on the output.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
In case an unidentified CPU type is detected it now returns
i.MX??, in a const char.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Markus Hubig <mhubig@imko.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add at91sam9x5ek board support, this board support the following SoCs
AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35
Using at91sam9x5ek_nandflash to configure for the board
Now only supports NAND with software ECC boot up
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[move MAINTAINERS entry to right place]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
For the DA8xx family of SoCs, the set_cpu_clk_info() function was not
initialising the DSP frequency, leading to 'bdinfo' command output such as:
[...snip...]
ARM frequency = 300 MHz
DSP frequency = -536870913 MHz
DDR frequency = 300 MHz
This commit provides a separate implementation of set_cpu_clk_info() for
the DA8xx SoCs that initialises the DSP frequency to zero (since
currently the DSP is not enabled by U-Boot on any DA8xx platform). The
separate implementation is justified because there is no common code
between DA8xx and the other SoC families. It is now much easier to
understand the flow of the two separate functions.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Hadli, Manjunath <manjunath.hadli@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Replace a magic number for the DDR2/mDDR PHY clock ID with a proper
definition. In addition, don't request this clock ID on DA830 hardware,
which does not have a DDR2/mDDR PHY (or associated PLL controller).
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
On the DA830, UART2's clock is derived from PLL controller 0 output 2.
On the DA850, it is in the ASYNC3 group, and may be switched between PLL
controller 0 or 1. Fix the definition of the ID to match.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Tidy up the clock IDs defined for the DA8xx SOCs. With this new structure in
place, it is clear how to define new clock IDs, and how these map to the
numbers presented in the technical reference manual.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
- Move definition of the EEPROM contents to <asm/arch/sys_proto.h>
- Make some defines a little less generic now.
- Pinmux must be done by done by SPL now.
- Create 3 pinmux functions, uart0, i2c0 and board.
- Add pinmux specific to Starter Kit EVM for MMC now.
Signed-off-by: Tom Rini <trini@ti.com>
- Board requires gpio0 #7 to be set to power DDR3.
- Board uses DDR3, add a way to determine which DDR type to call
config_ddr with.
- Both of the above require filling in the header structure early, move
it into the data section.
Signed-off-by: Tom Rini <trini@ti.com>
The intention has always been (and boards are to support) an i2c EEPROM
that will identify what hardware they are, allowing a single binary to
support multiple boards. As such, remove the 'evm.c' file as there is
nothing EVM centric in it currently, only SoC peripheral configuration.
Signed-off-by: Tom Rini <trini@ti.com>
In order to support DDR3 as well as DDR2, we need to perform the same
init sequence, but with different values. So change config_ddr() to
toggle setting pointers/etc for what DDR2 wants, and then calling.
Signed-off-by: Tom Rini <trini@ti.com>
The ddr_regs struct was incorrectly offset after the dt0wiratio0 entry.
Correct this by documenting a missing register that will be used at some
point in the future (when write leveling is supported). Further, the
cmdNcs{force,delay} fields are undocumented and we have been setting
them to zero, remove. Next, setting of the
'DATAn_REG_PHY_USE_RANK0_DELAYS field belongs with the rest of the
ddr_data entries, so program it there. Finally, comment on how we are
configuring the DATA1 registers that correspond to the DATA0 (dt0)
registers defined in the struct.
Signed-off-by: Tom Rini <trini@ti.com>
The various ratio1 fields are not documented in any of the documentation
I can find. Removing these and testing has yielded success, so remove
the code that sets them and move their locations into the reserved
fields.
Signed-off-by: Tom Rini <trini@ti.com>
This function sets a number of related registers to the same value (the
registers in question all have the same field descriptions and are
related in operation). Rather than defining a struct and setting the
value repeatedly, just pass in the value.
Signed-off-by: Tom Rini <trini@ti.com>
Rather than defining our own structs to note what to use when
programming the EMIF and related re-use the emif_regs struct.
Signed-off-by: Tom Rini <trini@ti.com>
A number of memory initalization functions were int and always returned
0. Further it's not feasible to be doing error checking here, so simply
turn them into void functions.
Signed-off-by: Tom Rini <trini@ti.com>
- Remove the call to set ddrctrl->ddrioctrl as it's all zeros.
- Comment what we're really setting in ddrctrl->ddrckectrl which is that
we're operating in the normal mode where EMIF/PHY clock is controlled
by the PHY.
Signed-off-by: Tom Rini <trini@ti.com>
EMIF parameters are calculated based on the AC timing
parameters from the SDRAM datasheet and the DDR frequency.
Current values for these paramters in AM335x U-Boot code,
though reliable, are not fully optimal. The most optimal
settings can be derived based on the guidelines published
at [1]. A pre-computed set of values with the most optimum
settings for AM335x EVM and BeagleBone can be found at [2].
[1] http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips
[2] http://processors.wiki.ti.com/index.php/OMAP_and_Sitara_CCS_support#AM335x
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Depending on if we have DDR2 or DDR3 on the board we will need to call
ddr_pll_config with a different value. This call can be delayed
slightly to the point where we know which type of memory we have.
Signed-off-by: Tom Rini <trini@ti.com>
We need to pass in the type of memory that is connected to the board.
The only reliable way to do this is to know what type of board we are
running on (which later will be knowable in s_init()). For now, pass in
the value of DDR2.
Signed-off-by: Tom Rini <trini@ti.com>
Rework the EMIF4/DDR code slightly to setup the structs that
config_cmd_ctrl and config_ddr_data take to be setup at compile time and
mark them as const. This lets us simplify the calling path slightly as
well as making it easier to deal with DDR3.
Signed-off-by: Tom Rini <trini@ti.com>
With the previous bugfix we now don't need to set two different REF_CTRL
values and instead set the final value.
Signed-off-by: Tom Rini <trini@ti.com>
When we change SDRAM_CONFIG this triggers a refresh based on all of the
parameters that we have programmed so we must do this last.
Signed-off-by: Tom Rini <trini@ti.com>
We do not need to check for EMIF_GCLK and L3_GCLK being active. This
was a hold-over from bringup and no longer required.
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds pin mux settings for CPSW switch found on
TI AM335X based boards (MII and RGMII modes).
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split pinmux into separate patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
