The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 10-bits width.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This re-syncs omap3 DTS file with current file from
Linux v4.14-rc1 to ensure a consistent configuration. Upstream
Linux removed the redundant Interrupt-parent property from usbhsohci,
usbhsehci, ssi_port1 and ssi_port2 sub nodes.
Signed-off-by: Karthik Tummala <karthik@techveda.org>
With DM enabled, gpio numbering is assigned based on the
probed order of gpios, irrespective of the gpio base. So enable
all necessary gpios in SPL.
Fixes: edf25d94d55c (“ARM: dts: OMAP5+: Enable gpio in SPL”)
Reported-by: Gou, Hongmei <h-gou@ti.com>
Tested-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch adds support for authentication of both plain
text and encrypted binaries. A new SECDEV package is needed
to enable encryption of binaries by default for AM3x.
The ROM authentication API detects encrypted images at
runtime and automatically decrypts the image if the
signature verification passes.
Addition of encryption on AM3x results in a change in the
image format. On AM4x, AM5x and, on AM3x devices signing
clear test images, the signature is appended to the end of the
binary.
On AM3x, when the SECDEV package is used to create signed
and encrypted images, the signature is added as a header
to the start of the binary. So the binary size calculation
has been updated to reflect this change.
The signing tools and encrypted image format for AM3x
cannot be changed to behave like AM4x and AM5x to
maintain backward compatibility with older Sitara
M-Shield releases.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
With the device tree ported from Linux 4.13, this enables
Driver Model and Device Tree support for the am3517-evm
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
To keep the DTS and DTSI files clean and in sync with Linux, new
u-boot.dtsi files are added.
There are some spacing issues in the patch, but they appear to be
present in the Linux source files. I'll try to get to fixing them there,
and do a future re-sync at a later date.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
On ARCH_OMAP2PLUS platforms we know what the DDR layout is going to be,
and that it is safe to use SPL_STACK_R and provide a default value for
it. select this and re-sync the defconfigs.
Signed-off-by: Tom Rini <trini@konsulko.com>
With DM now enabled with the device tree pulled from Linux, we can
enable DM_I2C in U-Boot.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add DM_I2C_COMPAT to da850_am18xxevm to fix warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A few small additional items are needed to support DM_SPI and
DM_SERIAL, so those were added to da850-evm-u-boot.dtsi
Signed-off-by: Adam Ford <aford173@gmail.com>
The ClearFog Base boot from UART when setting the DIP switches to 01001.
Unfortunately, the SPL code sometimes fails to detect the UART boot
method at run-time. Add an alternative SAR UART boot value to fix this.
Note that this alternative value is not documented (Armada 38x Hardware
Specifications, Table 48). But experimentations showed it on the
ClearFog Base.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
dram_ecc_scrubbing() had code to skip unused DRAM banks but it would not
work because mvebu_sdram_bs() returns 0 and the code was subtracting 1
before checking the size. Remove the -1 from the bank size and the +1
from the total which will skip unused banks and still calculate the
correct size. Put the -1 where it is needed for scrubbing via the xor
engine.
Reported-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The Armada-38x has 1.8GHz and 2.0GHz variants. Add entries for these
variants to the sar_freq_tab.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Display more information about the current RAM configuration. With these
changes the output on a 88F6820 board is
SoC: MV88F6820-A0 at 1600 MHz
DRAM: 2 GiB (800 MHz, 32-bit, ECC not enabled)
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
These SoCs are network packet processors (switch chips) with integrated
ARMv7 cores. They share a great deal of commonality with the Armada-XP
CPUs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_MVNETA
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The PHY reset GPIOs were missing from the DT, add them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
As per updated board design, different QSPI flash
is connected on boards, hence change QSPI flash type
from Micron n25q512a device to spansion s25fs512s
device in dts and config.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
It is not necessary for every SoC to have 2 SATA controller.
So put SATA1, SATA2 code under respective defines.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch provides default implementations of the two functions
set_uart_mux_conf and set_mux_conf_regs. Hence boards not using
them do not need to provide their distinct empty definitions.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds support for stm32h7 soc family, stm32h743
discovery and evaluation boards.
For more information about STM32H7 series, please visit:
http://www.st.com/en/microcontrollers/stm32h7-series.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adapts stm32h743 disco and eval dts files to match
with U-boot requirements or add features wich are not yet
upstreamed on kernel side :
_ Add RCC clock driver node and update all clocks phandle
accordingly.
By default, on kernel side, all clocks was temporarly
configured as a phandle to timer_clk waiting for a RCC
clock driver to be available.
On U-boot side, we now have a dedicated RCC clock driver, we
can configured all clocks as phandle to this driver.
All this binding update will be available soon in a kernel tag,
as all the bindings have been acked by Rob Herring [1].
[1] http://lkml.iu.edu/hypermail/linux/kernel/1704.0/00935.html
_ Align STM32H7 serial compatible string with the one which will be
available in next kernel tag. The bindings has been acked by
Rob Herring [2].
This compatible string will be usefull to add stm32h7 specific
feature for this serial driver.
[2] https://lkml.org/lkml/2017/7/17/739
_ Add gpio compatible and aliases for stm32h743
_ Add FMC sdram node with associated new bindings value to
manage second bank (ie bank 1).
_ Add missing HSI and CSI oscillators nodes needed
by STM32H7 RCC clock driver.
Clock sources could be:
_ HSE (High Speed External)
_ HSI (High Speed Internal)
_ CSI (Low Power Internal)
These clocks can be used as clocksource in some configuration.
By default, HSE is selected as clock source.
_ Set HSE to 25Mhz for stm32h743i-disco and eval board
By default, the external oscillator frequency is defined at
25 Mhz in SoC stm32h743.dtsi file.
It has been set at 125 Mhz in kernel DT temporarly waiting for
RCC clock driver becomes available.
As in U-boot we got a RCC clock driver, the real value of HSE
clock can be used.
_ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl,
pwrcfg and gpio nodes.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This file is imported from linux kernel v4.13
Add device tree support for STM32H743 evaluation board.
This board offers :
_ STM32H743XIH6 microcontroller with 2 Mbytes of
Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
_ 5.7” 640x480 TFT color LCD with touch screen
_ Ethernet compliant with IEEE-802.3-2002
_ USB OTG HS and FS
_ I2 C compatible serial interface
_ RTC with rechargeable backup battery
_ SAI Audio DAC
_ ST-MEMS digital microphones
_ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
_ 8Mx32bit SDRAM, 1Mx16bit SRAM and 8Mx16bit NOR Flash
_ 1-Gbit Twin Quad-SPI NOR Flash
_ Potentiometer
_ 4 colored user LEDs
_ Reset, wakeup, tamper or key buttons
_ Joystick with 4-direction control and selector
_ Board connectors :
Power jack
3 USB with Micro-AB
RS-232 communications
Ethernet RJ45
FD-CAN compliant connection
Stereo headset jack including analog microphone input
2 audio jacks for external speakers
microSD™ card
JTAG/SWD and ETM trace
_ Expansion connectors:
Extension connectors and memory connectors for daughterboard
or wire-wrap board
_ Flexible power-supply options: ST-LINK USB VBUS or external
sources
_ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
capability: mass storage, virtual COM port and debug port
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All these files are imported from linux kernel v4.13
Add device tree support for STM32H743 SoC and discovery
board. This board offers :
_ STM32H743XIH6 microcontroller with 2 Mbytes of
Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
_ 5.7” 640x480 TFT color LCD with touch screen
_ Ethernet compliant with IEEE-802.3-2002
_ USB OTG HS
_ I2 C compatible serial interface
_ ST-MEMS digital microphones
_ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
_ 8Mx32bit SDRAM
_ 1-Gbit Twin Quad-SPI NOR Flash
_ Reset, wakeup, or key buttons
_ Joystick with 4-direction control and selector
_ Board connectors :
1 USB with Micro-AB
Ethernet RJ45
Stereo headset jack including analog microphone input
microSD™ card
RCA connector
JTAG/SWD and ETM trace
_ Expansion connectors:
Arduino Uno compatible Connectors
2 x PIO connectors (PMOD and PMOD+)
_ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
capability: mass storage, virtual COM port and debug port
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update ehci and ohci node's compatible string in order to
use ehci-generic and ohci-generic drivers.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On STi 96boards, configure by default the micro USB connector
(managed by DWC3 hardware block) in peripheral mode.
This will allow to use fastboot feature.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It configures the internal glue
logic and syscfg registers.
Part of this code been extracted from kernel.org driver
(drivers/usb/dwc3/dwc3-st.c)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
reset-names property is needed to use the reset
API for STi sdhci driver.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of having every board file to add its own g_dnl_bind_fixup()
implementation, move it to the common imx6 SPL code.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
After Simon's patch, the dtoc can work with 64bit address,
so we need to fix reg number for it.
Depend on Simon's patch set:
https://patchwork.ozlabs.org/cover/807266/
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK3368 TPL stage always returns to the BootROM, so it has no need
for the eMMC, SD and SPI nodes. This marks those nodes (that should
be included in SPL, but not TPL) as 'u-boot,dm-spl'.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On the RK3399-Q7, we need to turn on the on-module USB hub before using the
USB host interfaces (only the OTG interface is directly connected to the edge
connector). This drops the deprecated 'rockchip,vbus-gpio' property and uses
a fixed regulator to turn on the USB hub.
References: 26a8b80 "usb: host: xhci-rockchip: use fixed regulator to control vbus"
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support for Vyasa RK3288 initial board
from Amarula Solutions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
On the RK3399, we will have either OF_PLATDATA or full OF_CONTROL
enabled: this allows the use of syscon to retrieve the addresses of
GRF and SGRF (except for the early debug UART setup, which runs so
early that the device-model is not initialised).
This removes the hard-coded addresses and goes through syscon to
retrieve the base-addresses of GRF and SGRF. After that, we use
the structure definitions to locate the respective registers.
In addition to this, the inclusion of header files is also cleaned up:
- all headers are included at the beginning (there was a spurious
inclusion of the grf header from within a function)
- all #include statements for unused headers are removed
- the remaining #include statements are sorted (while keeping common.h
included in front)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To support bootstage recording, we want to mark our DM timer as the
tick-timer; this triggers the support for 'trying harder' to read the
timer in the Rockchip DM timer driver, even if the device model isn't
ready yet.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Unfortunately, the integrated macphy default is enabled, which will
increase power consuming, if we do not use this PHY. So let's disable
it at first, which will save power consuming. If we really use it, then
enable it in driver level.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To support fastboot "fastboot reboot-bootloader" cmd.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds USB OTG/EHCI/OHCI nodes for evb-rv1108 USB ports.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Update these macros to use all upper-case to avoid checkpatch
warnings:
ENET_25MHz,
ENET_50MHz,
ENET_125MHz,
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The current mechanism using SCR/GPR registers work well when
the serial downloader boot mode has been selected explicitly
(either via boot mode pins or using bmode command). However,
in case the system entered boot ROM due to unbootable primary
boot devices (e.g. empty eMMC), the SPL fails to detect that
it has been downloaded through serial loader and tries to
continue booting from eMMC:
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The only known way to reliably detect USB serial downloader
is by checking the USB PHY receiver block power state...
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
This macro allows to detect whether the USB PHY is active. This
is helpful to detect if the boot ROM has previously started the
USB serial downloader.
The idea is taken from the mfgtool support in the NXP U-Boot:
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/?h=imx_v2016.03_4.1.15_2.0.0_ga&id=a352ed3c5184b95c4c9f7468f5fbb5f43de5e412
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Starting from PXs3, the bit fields of RSTCTRL, CLKCTRL registers
will change every SoC. There is no more point to define bitfields
in the common header file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The main difference between Pro4 and PXs2/LD6b is the Denali NAND
IP version. This is now distinguished by DT. Merge the two defconfig
files into uniphier_v7_defconfig.
Update the README.uniphier too.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
legacy_hole_base_k and legacy_hole_size_k are defined but
not used.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With bootstage we need access to the timer before driver model is set up.
To handle this, put the required state in global_data and provide a new
function to set up the device, separate from the driver's probe() method.
This will be used by the 'early' timer also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This adds support to Intel Cherry Hill board, a board based on
Intel Braswell SoC. The following devices are validated:
- serial port as the serial console
- on-board Realtek 8169 ethernet controller
- SATA AHCI controller
- EMMC/SDHC controller
- USB 3.0 xHCI controller
- PCIe x1 slot with a graphics card
- ICH SPI controller with an 8MB Macronix SPI flash
- Integrated graphics device as the video console
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
FSP's built-in UPD configuration enables PUNIT power configuration,
but on B0 stepping, this causes CPU hangs in fsp_init(). Disable it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds microcode device tree fragment for Braswell B0 (406C2),
C0 (406C3) and D0 (406C4) stepping SoC.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds initial Intel Braswell SoC support. It uses Intel FSP
to initialize the chipset.
Similar to its predecessor BayTrail, there are some work to do to
enable the legacy UART integrated in the Braswell SoC.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
FSP spec 1.1 adds 3 new APIs and their offsets are in the header.
Update the 'fsp hdr' command to show these new entries.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a VBT is given to an FSP that supports graphics initialization,
the FSP will produce a graphics info HOB that contains all necessary
information for the linear frame buffer of the integrated graphics
device. This adds a DM video driver for it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that binman is able to recognize the Video BIOS Table entry,
add such one in the u-boot.dtsi.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds Kconfig options for Video BIOS Table which is normally
required if you are using an Intel FSP firmware that is complaint
with spec 1.1 or later to initialize the integrated graphics device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a new HOB type for graphics information introduced in FSP
spec 1.1. When graphics capability is included in FSP and enabled,
FSP produces an FSP_GRAPHICS_INFO_HOB as described in the EFI PI
specification which provides information about the graphics mode and
framebuffer.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
FSP spec 1.1 adds one more member to the struct common_buf to
determine the memory size that can be reserved by FSP below "top
of low usable memory" for bootloader usage. This new member uses
the reserved space so that it is still compatible with previous
FSP spec 1.0.
A new HOB (FSP_HOB_RESOURCE_OWNER_BOOTLOADER_TOLUM_GUID) is also
published when common_buf.tolum_size is valid and non zero.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Nothing CONFIG_SOC_DA830 anymore, so let's remove it and
the one remaining source file for it. It appears to have been
abandoned a while ago.
Signed-off-by: Adam Ford <aford173@gmail.com>
commit b63b995 (arm: dts: Add u-boot specific compatibles) separated out
u-boot specific compatibles from dts files.
The u-boot specifics were moved in *-u-boot.dtsi files for all dra7
platforms except dra7-evm.
Without it the SD card is broken on DRA7-evm because the regulator cannot
be enabled.
Fix it by adding the missing dra7-evm-u-boot.dtsi with the needed
properties.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
When the OP-TEE image is built for secure paging the load address may be
in SRAM, remove checks that prevent this.
Signed-off-by: Harinarayan Bhatta <harinarayan@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
All these places seem to inherit the codes from the MMC driver where
a FIXME was put in the comment. However the correct operation after
read should be cache invalidate, not flush.
The underlying drivers should be responsible for the cache operation.
Remove these codes completely.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: York Sun <york.sun@nxp.com>
Commit 6ae4c3efbd ("ARM: DRA7: Add pinctrl register definitions")
has added new macros for pinmux configuration in line with the kernel
definitions. Cleanup the old pinctrl macros from the common header
file so that they are not used by any new boards.
Signed-off-by: Suman Anna <s-anna@ti.com>
Use the CONFIG_XXXX_BOOT to indicate the boot media, instead of
the CONFIG_SYS_USE_XXXX option, which is declared by
CONFIG_SYS_EXTRA_OPTIONS option.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
As said in READRE.kconfig, include/configs/*.h will be removed
after all options are switched to Kconfig. As the first step,
remove the follow line from include/configs/*.h.
#include <asm/hardware.h>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
To prepare to remove the SoCs options such as SAMA5D2, SAMA5D3
and SAMA5D4 from the CONFIG_SYS_EXTRA_OPTIONS option which is
deprecated, add the SoC options to Kconfig.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
The SAMA5D27-SiP (System in Package) integrates the SAMA5D2
with 1Gbit DDR2-SDRAM in a single package.
The SAMA5D27 SOM1 embeds a 64Mbit QSPI flash, KSZ8081 Phy and
Mac-address EEPROM.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SAMA5D2 SiP(System in Package) has different Chip IDs in the
CHIPID and CHIP_EXID registers.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the boot device for booting from the QSPI flash.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Refer to the commit 70f8c8316ad(PMC: add new mck function to lower
rate while switching) from AT91Bootstrap.
While switching to a lower clock source, we must switch the clock
source first instead of last. Otherwise, we could end up with
too high frequency on internal bus and peripherals.
This happens on SAMA5D2 as exitting from the ROM code.
Add a function pmc_mck_init_down() to allow this sequence.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As said in 29.5.7 section of SAMA5D2 datasheet, before switching to
the crystal oscillator, a check must be carried out to ensure that
the oscillator is present and that its freqency is valid.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a function to display the company's logo and board information
via the API from DM_VIDEO. This function can be shared by other
atmel boards, so locate it in board/atmel/common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For sama5d2, add the sfr node with syscon support.
In order to access the SFR_UTMICKTRIM register for the utmi clock
driver, add the phandle property for the utmi node to point to the
sfr node.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
By default, it is assumed that the UTMI clock is generated from
a 12 MHz reference clock (MAINCK). If it's not the case, the FREQ
field of the SFR_UTMICKTRIM has to be updated to generate the UTMI
clock in the proper way.
The UTMI clock has a fixed rate of 480 MHz. In fact, there is no
multiplier we can configure. The multiplier is managed internally,
depending on the reference clock frequency, to achieve the target
of 480 MHz.
The patch is cloned from the patch of mailing-list:
[PATCH v2] clk: at91: utmi: set the mainck rate
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
[trini: Depend on SPL_DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_EMIF4
CONFIG_SDRC
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The DTS files had some spacing issues and they needed fixing. This
pull re-sync's the OMAP3xx related DTS files with Linux 4.13-RC5.
To keep the DTS and DTSI files clean and in sync with Linux, new
u-boot.dtsi files are added.
Signed-off-by: Adam Ford <aford173@gmail.com>
V3: The resync broke card detect on MMC1 on Logic PD's Torpedo,
so we add the cd-invert to the Torpedo's -u-boot.dtsi file.
V2: Add the u-boot.dtsi files for OMAP3, OMAP36xx, and Torpedo
Remove the need for the second patch in the series
Fix the building warning as below:
---8<----
Warning (reg_format): "reg" property in /i2c-gpio-0/pcf8563@50 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /i2c-gpio-0/pcf8563@50
Warning (avoid_default_addr_size): Relying on default #size-cells value for /i2c-gpio-0/pcf8563@50
--->8----
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Add support for detection
of SR2.1 version of DRA71x family of processors.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Import include/linux/dma-direction.h from Linux 4.13-rc7 and delete
duplicated definitions of enum dma_data_direction.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add space around operator "+", make it
match the coding style.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Macro VA_BITS and PTE_BLOCK_BITS are not used
in the code, so remove them.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The R8A7796 XHCI USB nodes are missing from r8a7796 dtsi, add them.
These nodes don't come from mainline Linux, yet the DT binding is
similar enough to R8A7795 which already has those in mainline and
once the nodes hit mainline, this DT should be resynched.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The R8A7796 EHCI USB nodes are missing from r8a7796 dtsi, add them.
These nodes don't come from mainline Linux, yet the DT binding is
similar enough to R8A7795 which already has those in mainline and
once the nodes hit mainline, this DT should be resynched.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the RCar Gen3 DTS and headers from upstream Linux kernel v4.13,
commit 569dbb88e80deb68974ef6fdd6a13edb9d686261 . This includes both M3
and H3 ULCB and Salvator-X boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This allows to scan the DT including all "clocks" node's sub-nodes
in which fixed-clock are defined.
All fixed-clock should be defined inside a clocks node which collect all
external oscillators. Until now, all clocks sub-nodes can't be binded except
if the "simple-bus" compatible string is added which is a hack.
Update test.dts by moving clk_fixed node inside clocks.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a convenience macro to iterate over subnodes of a node. Make use of
this where appropriate in the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert SANDBOX_BITS_PER_LONG to Kconfig and assign it a correct
number depending on which host we are going to build and run.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It seems most of the time we are building and running sandbox on 64-bit host.
But we do support 32-bit host as well. Introduce Kconfig option for this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the code to set the ethernet mac address from eeprom by using
the common code from the common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace the code to set the ethernet mac address with the code from
the common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Create board/$(VENDOR)/common folder to accommodate the common code
shared by other atmel boards, now put the code to set ethernet mac
address from eeprom, which uses the i2c eeprom driver.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for selecting proper dtb for
am57xx BeagleBoard X15 revC u-boot from FIT
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
AM571x supports DDR running at 666MHz. Right now it is
clocked at 532MHz which is lower than what is supported.
In order to have maximum performance on AM571-IDK,
switch DDR to 666MHz.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for selecting proper dtb for
dra76x u-boot from FIT.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Separate out u-boot specific compatibles from dts files.
This will help in syncing dts files in future.
Also these will get deleted eventually once respective drivers
are capable of handling Linux dts files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
dra76-evm has the ddr parts connectedi running at 666MHz:
EMIF1: MT41K512M16HA-125 AIT:A x 2
EMIF2: MT41K512M8RH-125-AAT:E x 4
Add support for configuring the above DDR parts.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76-evm uses lp8736 and tps65917 pmic for powering on
various peripherals. Add data for these pmics and register
for dra76-evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76 family is a high-performance, infotainment application
device, based on OMAP architecture on a 28-nm technology.
This contains most of the subsystems, peripherals that are
available on dra74, dra72 family. This SoC mainly features
Subsystems:
- 2 x Cortex-A15 with max speed of 1.8GHz
- 2 X DSP
- 2 X Cortex-M4 IPU
- ISS
- CAL
- DSS
- VPE
- VIP
Connectivity peripherals:
- 1 USB3.0 and 3 USB2.0 subsystems
- 1 x SATA
- 2 x PCI Express Gen2
- 3-port Gigabit ethernet switch
- 2 x CAN
- MCAN
Adding CPU detection support for the dra76 ES1.0 soc
and update prcm, control module, dplls data.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
LP87565 is present on dra76-evm. Select it for
TARGET_DRA7XX_EVM.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It is not necessary that ldo1 is used to power on mmc.
So, add support for passing ldo registers for powering on mmc.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
It is not necessary all omap5+ based uses the same PMIC
to poweron mmc. So add support for enabling mmc based on board.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
CCN-504 HPF registers were believed to be accessible only from EL3.
However, recent tests proved otherwise. Remove checking for exception
level to re-enable L3 cache flushing for all levels.
Signed-off-by: York Sun <york.sun@nxp.com>
Tested-by: Zhao Qiang <qiang.zhao@nxp.com>
The pcie config space of ls1088a is different from ls2080a.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In case high region memory doesn't have enough space for Management
Complex (MC), the return value should indicate a failure so the
caller can handle it accordingly.
Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Ebony Zhu <ebony.zhu@nxp.com>
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Low Frequency Periodic Singaling (LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter settings
Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receive
Compliance test failure for a 100mV threshold.
Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature
Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values.
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Low Frequency Periodic Signaling(LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter
settings
Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receiver
Compliance test failure for a 100mV threshold.
Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature
Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds support for RGMII protocol
NXP's LDPAA2 support RGMII protocol. LS1088A is the
first Soc supporting both RGMII and SGMII.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch add support of LS1088AQDS platform.
The LS1088A QorIQTM Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports the
LS1088A QorIQ Architecture processor.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Disabled NAND in board header file]
Reviewed-by: York Sun <york.sun@nxp.com>
WIP: disable NAND for LS1088ARDB
For QSPI and IFC addresses execution shouldn't be allowed
when u-boot running from DDR. Revise the MMU final table
to enforce execute-never bits.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
According current code base, CONFIG_LS1012A should be
CONFIG_ARCH_LS1012A, or function fsl_fdt_disable(blob) will be
wrongly called to disable all dwc3 USB nodes on LS1012A, which
cause Linux USB function stop working at all.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080 family has CCN-504 cache coherent interconnet. Other SoCs
in LSCH3 family may have differnt interconnect.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Adds header address for PPA to be validated during ESBC phase for
ARCH_LS2088 and QSPI_BOOT. Moves sec_init prior to ppa_init(). It
must be initialized before the PPA.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Unify memory map for Layerscape based platforms. This patch includes
changes in bootscript, bootscript header and PPA header addresses
change as per unified memory map.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CoreLink Cache Coherent Interconnect (CCI) provides full cache
coherency between two clusters of multi-core CPUs and I/O coherency
for devices and I/O masters.
This patch add new config option SYS_FSL_HAS_CCI400 and moves
existing register space definaton of CCI-400 bus to fsl_immap to be
shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET
in Kconfig.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message, squashed patches for armv8 and armv7]
Reviewed-by: York Sun <york.sun@nxp.com>
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig.
Update defconfigs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on
USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and
LAN78XX options under new menu. Finally update the defconfigs that need
CONFIG_USB_HOST_ETHER.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With Makefiles testing for $(SPL_TPL_)SYSRESET, we need SPL_SYSRESET
for do_reset() in SPL for Rockchip SoCs.
References: 87c16d4 "drivers: spl: consistently use the $(SPL_TPL_) macro"
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
syscon id table need a dummy member as NULL ending, or else system
will panic while try to match a compatible in this table as a list.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Sometimes it's helpful to know the reset reason caused in the SoC.
Add reset reason detection for the RK3288 SoC.
This will set an environment variable which represents the reset reason.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
