Commit graph

183 commits

Author SHA1 Message Date
Masahiro Yamada
365475e6d1 Move #ifdef(CONFIG_DISPLAY_CPUINFO) from caller to callee
- When CONFIG_DISPLAY_CPUINFO is not enabled,
   print_cpuinfo() should be defined as an empty function
   in a header, include/common.h

 - Remove #ifdef CONFIG_DISPLAY_CPUINFO .. #endif
   from caller, common/board_f.c and arch/arm/lib/board.c

 - Remove redundant prototypes in arch/arm/lib/board.c,
   arch/arm/include/asm/arch-am33x/sys_proto.h and
   board/nokia/rx51/rx51.h, keeping the one in include/common.h

 - Add #ifdef CONFIG_DISPLAY_CPUINFO to the func definition
   where it is missing

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19 11:10:05 -05:00
Sourav Poddar
b56e71e2d4 am43xx: Add qspi support
Add QSPI definitions and clock configuration support.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-02-18 22:41:08 +05:30
Albert ARIBAUD
e97f9d817e Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-01-29 14:07:50 +01:00
Dan Murphy
8cffe5bd0d spl: common: Support for USB MSD FAT image loading
Add SPL support to be able to detect a USB Mass Storage device
connected to a USB host.  Once a USB Mass storage device is detected
the SPL will load the u-boot.img from a FAT partition to target address.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2014-01-24 16:59:22 -05:00
Satyanarayana, Sandhya
e9b13ce0b6 ARM: AM335x: Enable DDR dynamic IO power down
This patch enables dynamically powering down the
IO receiver when not performing a read on boards using DDR3.
This optimizes both active and standby power consumption.
This bit is not set on EVM SK and EVM 1.5 and later boards.
Setting the same.

This has been tested on PG2.0 EVM1.5, EVM1.2, EVM-SK, BBB.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
2014-01-24 11:38:39 -05:00
Lokesh Vutla
b5e01eecc8 ARM: AM43xx: GP_EVM: Add support for DDR3
GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH).
Adding details for the same.
Below is the brief description of DDR3 init sequence(SW leveling):
-> Enable VTT regulator
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program leveling registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:45 -05:00
Lokesh Vutla
d3daba10f1 ARM: AM43xx: EPOS_EVM: Add support for LPDDR2
AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief description of LPDDR2 init sequence:
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
-> Wait till initialization is complete and the configure MR registers.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:44 -05:00
Lokesh Vutla
cf04d0326b ARM: AM43xx: clocks: Update DPLL details
Updating the Multiplier and Dividers value for all DPLLs.
Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value
returned the MPU DPLL is locked.
At different OPPs follwoing are the MPU locked frequencies.
OPP50	300MHz
OPP100	600MHz
OPP120	720MHz
OPPTB	800MHz
OPPNT	1000MHz
According to the latest DM following is the OPP table dependencies:
	VDD_CORE 	VDD_MPU
	OPP50		OPP50
	OPP50 		OPP100
	OPP100		OPP50
	OPP100		OPP100
	OPP100		OPP120
So at different OPPs of MPU it is safest to lock CORE at OPP_NOM.
Following are the DPLL locking frequencies at OPP NOM:
Core locks at 1000MHz
Per locks at 960MHz
LPDDR2 locks at 266MHz
DDR3 locks at 400MHz

Touching AM33xx files also to get DPLL values specific to board but no
functionality difference.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:01 -05:00
Lokesh Vutla
4892495e36 ARM: AM43xx: mux: Update mux data
Updating the mux data for UART, adding data for i2c0 and mmc.
And also updating pad_signals structure.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:01 -05:00
Lokesh Vutla
1fb68b842e ARM: AM43xx: Update Current Booting devices list
Current Booting devices list is different from that of AM33xx.
Updating the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:01 -05:00
Sekhar Nori
9f1a8cd33f ARM: AM43XX: board: add support for reading onboard EEPROM
Add support for reading onboard EEPROM to enable
board detection.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:00 -05:00
Lokesh Vutla
369cbe1e1e ARM: AM43xx: Adapt to ti_armv7_common.h config file
Use ti_armv7_common.h config file to inclde the common
configs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:00 -05:00
Lokesh Vutla
7ca1b2a210 ARM: AM43xx: Update the base addresses of modules
PRCM, timer base addresses and offsets are different from
AM33xx. Updating the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:13:59 -05:00
Dan Murphy
052fb19603 arm: am437: Fix offset for USB registers
Fix the offset for the USB clock registers

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-12-12 14:54:22 -05:00
Albert ARIBAUD
f15ea6e1d6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/armv7/rmobile/Makefile
	doc/README.scrapyard

Needed manual fix:
	arch/arm/cpu/armv7/omap-common/Makefile
	board/compulab/cm_t335/u-boot.lds
2013-12-10 22:23:59 +01:00
Tom Rini
39245c8699 am33xx: Stop modifying certain EMIF4D registers
Based on the definitive guide to EMIF configuration[1] certain registers
that we have been modifying (and are documented registers) should be
left in their reset values rather than modified.  This has been tested
on AM335x GP EVM and Beaglebone White.

[1]: http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Matt Porter <matt.porter@linaro.org>
2013-12-04 08:11:45 -05:00
Ilya Ledvich
54e7445de9 cm_t335: add cm_t335 board support
Add cm_t335 board directory, config file. Enable build.

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[trini: Adapt Makefile]
Signed-off-by: Tom Rini <trini@ti.com>
2013-12-04 08:10:41 -05:00
Tom Rini
faca8ff55f Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2013-11-25 10:42:13 -05:00
pekon gupta
2c17e6d1d9 am335x: fix GPMC config for NAND and NOR SPL boot
GPMC controller is common IP to interface with both NAND and NOR flash devices.
Also, it supports max 8 chip-selects, which can be independently connected to
any of the devices.
But ROM code expects the boot-device to be connected to only chip-select[0].
Thus to resolve conflict between NOR and NAND boot. This patch:
- combines NOR and NAND configs spread in board files to common gpmc_init()
- configures GPMC based on boot-mode selected for SPL boot.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-21 13:33:41 -06:00
pekon gupta
beba5f04f2 mtd: nand: omap: make am33xx/elm.c as common driver for all OMAPx and AMxxxx platforms
ELM hardware engine which is used for ECC error detection, is present on all
latest OMAP SoC (like OMAP4xxx, OMAP5xxx, DRA7xxx, AM33xx, AM43xx). Thus ELM
driver should be moved to common drivers/mtd/nand/ folder so that all SoC
having on-chip ELM hardware engine can re-use it.
This patch has following changes:
- mv arch/arm/include/asm/arch-am33xx/elm.h arch/arm/include/asm/omap_elm.h
- mv arch/arm/cpu/armv7/am33xx/elm.c drivers/mtd/nand/omap_elm.c
- update Makefiles
- update #include <asm/elm.h>
- add CONFIG_NAND_OMAP_ELM to compile driver/mtd/nand/omap_elm.c
	and include in all board configs using AM33xx SoC platform.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-21 13:33:41 -06:00
Heiko Schocher
6789e84eca i2c, omap24xx: convert driver to new mutlibus/mutliadapter framework
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver

Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S  <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-11-13 06:18:17 +01:00
Albert ARIBAUD
85b8c5c4bf Merge branch 'iu-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h
2013-11-09 22:59:47 +01:00
Tom Rini
155d424a9a am33xx, davinci: Create and use <asm/davinci_rtc.h>
Create a common header file for the RTC IP block that is shared between
davinci and am33xx.

Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01 15:30:22 -04:00
Dan Murphy
3d799c7f5e usb: am437x: Add support for am437x xhci USB host
Add the support for the am437x xhci usb host.

The xHCI host on AM437 is connected to a usb2 phy so need to
add support to enable those clocks.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Enric Balletbo i Serra
94b32f60fe ARM: IGEP0033: Update timing to run DDR at 400MHz.
We can run the DDR at 400MHz, so update the timings for that purpose.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
2013-10-07 07:43:46 -04:00
Steve Kipisz
52f7d8442e am335x:Handle worst case scenario for Errata 1.0.24
In Errata 1.0.24, if the board is running at OPP50 and has a warm reset,
the boot ROM sets the frequencies for OPP100. This patch attempts to
drop the frequencies back to OPP50 as soon as possible in the SPL. Then
later the voltages and frequencies up set higher.

Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Adapt to current framework]
Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20 16:57:40 -04:00
Tom Rini
9721027aae am335x_evm: am33xx_spl_board_init function and scale core frequency
Add a am33xx_spl_board_init (and enable the PMICs) that we may see,
depending on the board we are running on.  In all cases, we see if we
can rely on the efuse_sma register to tell us the maximum speed.  In the
case of Beaglebone White, we need to make sure we are on AC power, and
are on later than rev A1, and then we can ramp up to the PG1.0 maximum
of 720Mhz.  In the case of Beaglebone Black, we are either on PG2.0 that
supports 1GHz or PG2.1.  As PG2.0 may or may not have efuse_sma set, we
cannot rely on this probe.  In the case of the GP EVM, EVM SK and IDK we
need to rely on the efuse_sma if we are on PG2.1, and the defaults for
PG1.0/2.0.

Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20 16:57:35 -04:00
Tom Rini
5287946c06 am33xx: Add the efuse_sma CONTROL_MODULE register
Starting with PG2.1 we have a register in the CONTROL_MODULE that is set
with the package type and maximum supported frequency.  Add this, and
the relevant mask/values.

Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20 11:01:26 -04:00
Tom Rini
6a0d803c7c am33xx: Add am33xx_spl_board_init function, call
We need to allow for a further call-out in spl_board_init.  Call this
am33xx_spl_board_init and add a __weak version.  This function may be
used to scale the MPU frequency up, depending on board needs.

Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20 11:01:26 -04:00
Albert ARIBAUD
e62d5fb0da Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-09-04 14:06:56 +02:00
Heiko Schocher
988ea35501 arm, am335x: add watchdog support
Add TI OMAP 16xx & 24xx/34xx 32KHz (non-secure) watchdog support.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2013-08-28 11:44:59 -04:00
Heiko Schocher
14c0158b18 arm, am335x: add some missing registers and defines for lcd and epwm support
- add missing register defines in struct cm_perpl
  epwmss0clkctrl
  epwmss2clkctrl
  lcdcclkstctrl
- add missing register defines in struct cm_dpll
  clklcdcpixelclk
- add struct pwmss_regs
- add struct pwmss_ecap_regs
- add LCD Controller base LCD_CNTL_BASE
- add PWM0 controller base PWMSS0_BASE

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
2013-08-28 11:44:59 -04:00
Heiko Schocher
dafd4db33a arm, am33xx: add defines for gmii_sel_register bits
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-08-28 11:44:59 -04:00
Tom Rini
c27efde68d am33xx: Correct and expand comments on CONFIG_SPL_MAX_SIZE
We had been allowing the max size to be larger than actually allowed by
the ROM.  Expand the commentary here to explain why we set these
locations.

Signed-off-by: Tom Rini <trini@ti.com>
2013-08-28 11:44:58 -04:00
Tom Rini
e20cc2ca15 Merge branch 'master' of git://88.191.163.10/u-boot-arm
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.

Conflicts:
	arch/arm/include/asm/arch-am33xx/hardware.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-08-18 14:14:34 -04:00
TENART Antoine
dcf846d5da Add TI816X support
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Fix warnings about vtp things in emif4.c, adapt AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15 18:38:37 -04:00
TENART Antoine
9ed6e41239 Prepare for TI816X : reuse existing code from TI814X
Rename some CONFIG_TI814X to a more generic CONFIG_TI81XX

Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Adapt for CONFIG_OMAP_COMMON changes, AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15 18:38:37 -04:00
Lokesh Vutla
c06e498a16 ARM: AM43xx: Add header files
Adding the following data:
-> Prcm structure
-> Base addresses
-> Pin mux structure.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15 08:51:10 -04:00
Heiko Schocher
0660481a59 ARM: AM33xx: Move s_init to a common place
s_init has the same outline for all the AM33xx based
board. So making it generic.
This also helps in addition of new Soc with minimal changes.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Lokesh Vutla
95cb69faeb ARM: AM33xx: Cleanup clocks layer
Cleaning up the clocks layer.
This helps in addition of new Soc with minimal
changes.
This is derived from OMAP4 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Lokesh Vutla
94d77fb656 ARM: AM33xx: Cleanup dplls data
Locking sequence for all the dplls is same.
In the current code same sequence is done repeatedly
for each dpll. Instead have a generic function
for locking dplls and pass dpll data to that function.

This is derived from OMAP4 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Heiko Schocher
b424aae4be arm, am33xx: add clk_get prototype
the clk_get() function is needed for the da8xx-fb video driver,
which is used on the am3xx based siemens boards.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
2013-08-10 10:38:06 +02:00
Steve Kipisz
cd8845d7a4 am335x_evm: Add support for the NOR module on the memory cape
This patch adds support for the NOR module that attaches
to the memory cape for a Beaglebone board. This does not
add booting support; only support so that you can boot from
SD/MMC and see the NOR module so that it can be programmed.

Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Clean up config changes slightly]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30 09:21:41 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Tom Rini
fbbbc86e8e Merge branch 'master' of git://git.denx.de/u-boot-arm
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.

Conflicts:
	arch/arm/dts/exynos5250.dtsi

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-12 10:36:48 -04:00
Axel Lin
87bd05d78f ARM: OMAP: GPIO: Fix valid range and enable usage of all GPIOs on OMAP5
The omap_gpio driver is used by AM33XX, OMAP3/4, OMAP54XX and DRA7XX SoCs.
These SoCs have different gpio count but currently omap_gpio driver uses hard
coded 192 which is wrong.

This patch fixes this issue by:
1. Move define of OMAP_MAX_GPIO to all arch/arm/include/asm/arch-omap*/gpio.h.
2. Update gpio bank settings and enable GPIO modules 7 & 8 clocks for OMAP5.

Thanks for Lubomir Popov to provide valuable comments to fix this issue.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Acked-by: Heiko Schocher <hs@denx.de>
2013-07-02 09:21:16 -04:00
Ilya Ledvich
58c86c7d1d am33xx: fix the ddr_cmdtctrl structure
Fix the wrong mapping between the DDR I/O control registers on AM33XX
SoCs and the software representation in the SPL code.
The most recent public TRM defines the following DDR I/O control registers
offsets:
 * ddr_cmd0_ioctrl : offset 0x44E11404
 * ddr_cmd1_ioctrl : offset 0x44E11408
 * ddr_cmd2_ioctrl : offset 0x44E1140C
 * ddr_data0_ioctrl: offset 0x44E11440
 * ddr_data1_ioctrl: offset 0x44E11444

While the struct ddr_cmdtctrl has also some reserved bits in the beginning.
The struct is mapped to the address 0x44E11404. As a result "cm0ioctl" points
to the ddr_cmd1_ioctrl register, "cm1ioctl" to the ddr_cmd2_ioctrl and etc.
Registers ddr_cmd0_ioctrl and ddr_data0_ioctrl are never configured because
of this mapping mismatch.

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
2013-07-02 09:21:16 -04:00
Tom Rini
348e47f766 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-06-22 07:38:12 -04:00
Heiko Schocher
7ea7f689ca arm, am33xx: move uart soft reset code to common place
move uart soft reset code to common place and call
this function from board code, instead of copy and paste
this code for every board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
[trini: Fix igep0033 build, remove 'regval' on pcm051]
Signed-off-by: Tom Rini <trini@ti.com>
2013-06-18 10:40:06 -04:00
Heiko Schocher
7b9c5d0bfd arm, am335x: make mpu pll config configurable
upcoming support for siemens boards switches mpu pll clk in board
code. So make this configurable.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
2013-06-18 09:18:46 -04:00
Heiko Schocher
49f7836500 arm, am33xx: move rtc32k_enable() to common place
move rtc32k_enable() to common place so all am33xx boards can use it.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-06-18 09:12:38 -04:00
Tom Rini
edfcf85a0a am33xx/omap4+: Move SRAM_SCRATCH_SPACE_ADDR to <asm/arch/omap.h>
The location of valid scratch space is dependent on SoC, so move that
there.  On OMAP4+ we continue to use SRAM_SCRATCH_SPACE_ADDR.  On
am33xx/ti814x we want to use what the ROM defines as "public stack"
which is the area after our defined download image space.  Correct the
comment about and location of CONFIG_SPL_TEXT_BASE.

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-06 08:57:45 -04:00
Tom Rini
4596dcc1d4 am33xx/omap: Move save_omap_boot_params to omap-common/boot-common.c
We need to call the save_omap_boot_params function on am33xx/ti81xx and
other newer TI SoCs, so move the function to boot-common.  Only OMAP4+
has the omap_hw_init_context function so add ifdefs to not call it on
am33xx/ti81xx.  Call save_omap_boot_params from s_init on am33xx/ti81xx
boards.

Reviewed-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-06-05 08:46:49 -04:00
Tom Rini
320d9746d3 am33xx: Correct NON_SECURE_SRAM_START/END
Prior to Sricharan's cleanup of the boot parameter saving code, we
did not make use of NON_SECURE_SRAM_START on am33xx, so it wasn't a
problem that the address was pointing to the middle of our running SPL.
Correct to point to the base location of the download image area.
Increase CONFIG_SPL_TEXT_BASE to account for this scratch area being
used.  As part of correcting these tests, make use of the fact that
we've always been placing our stack outside of the download image area
(which is fine, once the downloaded image is run, ROM is gone) so
correct the max size test to be the ROM defined top of the download area
to where we link/load at.

Signed-off-by: Tom Rini <trini@ti.com>

---
Changes in v2:
- Fix typo noted by Peter Korsgaard
2013-06-04 16:32:31 -04:00
SRICHARAN R
76db5b8f59 ARM: OMAP: Make omap_boot_parameters common across socs
omap_boot_parameters is same and defined for each
soc. So move this to a common place to reuse it
across socs.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-05-10 08:25:56 -04:00
Enric Balletbo i Serra
cc175e6353 Add DDR3 support for IGEP COM AQUILA/CYGNUS.
These boards uses Samsung K4B2G1646E-BIH9 a 2Gb E-die DDR3 SDRAM.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-05-10 08:25:55 -04:00
Matt Porter
035d563937 am33xx: add pll and clock support for TI814x CPSW
Enables required PLLs and clocks for CPSW on TI814x.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-05-10 08:25:54 -04:00
Tom Rini
86fdb1619a am335x: Really correct DDR timings on new BeagleBone part
The previous timings were done on the internal-only A1 board which has
different DDR part than all later revs.  The timings need a slight
adjustment to be correct in all cases with later revs.

Signed-off-by: Tom Rini <trini@ti.com>
2013-04-12 12:38:16 -04:00
Tom Rini
b996a3e9a8 am335x: Update timings for the beaglebone again
After further testing we can run DDR at 400MHz so update the timings
again.

Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tom Rini <trini@ti.com>
2013-04-10 10:04:40 -04:00
Tom Rini
74f40ea1bc am335x/ti814x: Correct MMC_BOOT_DEVICES_START/END
Given that on TI814x we have MMC1/2 swapped, we also need to swap them
in MMC_BOOT_DEVICES_START/END

Reported-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
2013-04-09 11:40:40 -04:00
Tom Rini
c3d2c24f6c OMAP3/4/5/AM33xx: Correct logic for checking FAT or RAW MMC
In the case of booting from certain peripherals, such as UART, we must
not see what the device descriptor says for RAW or FAT mode because in
addition to being nonsensical, it leads to a hang.  This is why we have
a test currently for the boot mode being within range.  The problem
however is that on some platforms we get MMC2_2 as the boot mode and not
the defined value for MMC2, and in others we get the value for MMC2_2.
This is required to fix eMMC booting on omap5_uevm.

Tested on am335x_evm (UART, NAND, SD), omap3_beagle (NAND, SD on
classic, SD only on xM rev C5) and omap5_uevm (SD, eMMC).

Signed-off-by: Tom Rini <trini@ti.com>
2013-04-08 11:29:34 -04:00
Andreas Bießmann
da634ae356 omap_gpmc: change nandecc command
With uppcoming BCH support on OMAP devices we need to decide between differnt
algorithms when switching the ECC engine.  Currently we support 1-bit hammign
and 8-bit BCH on HW backend.

In order to switch between differnet ECC algorithms we need to change the
interface of omap_nand_switch_ecc() also.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Thomas Weber <thomas.weber.linux@googlemail.com>
2013-04-08 11:29:05 -04:00
Andreas Bießmann
5bf299bc4f asm/omap_gpmc.h: consolidate common defines
arch/arm/include/asm/arch-am33xx/omap_gpmc.h and
arch/arm/include/asm/arch-omap3/omap_gpmc.h are almost the same, consolidate
the common parts into a new header.

Introduce a new asm/omap_gpmc.h which defines the command part and pulls in
the architecture specific one.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-08 11:29:05 -04:00
Tom Rini
c7ba18ad4b am335x_evm: Add better timings for the new BeagleBoard DDR3 part
Tested-by: Rao Bodapati <rao@circuitco.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:12 -04:00
Matt Porter
26fa57842b am33xx: support ti814x mmc reference clock
TI814x has a 192MHz hsmmc reference clock. Select that clock rate
when building for TI814x.

Signed-off-by: Matt Porter <mporter@ti.com>
2013-03-24 12:49:11 -04:00
Matt Porter
4fab8d7bbd am33xx: add dmm support to emif4 library
Adds a config_dmm() routine to support TI814X DMM configuration.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:11 -04:00
Matt Porter
8b029f22a6 am33xx: add ti814x specific register definitions
Support the ti814x specific register definitions within
arch-am33xx.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:11 -04:00
Matt Porter
b2e682f7a0 am33xx: refactor am33xx mux support and add ti814x support
AM33XX and TI814X have a similar mux though the pinmux register
layout and address space differ. Add a separate ti814x mux include
to support the TI814X-specific differences.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
2013-03-24 12:49:11 -04:00
Matt Porter
b43c17cba6 am33xx: refactor am33xx clocks and add ti814x support
Split clock.c for am335x and ti814x and add ti814x specific
clock support.

Signed-off-by: Matt Porter <mporter@ti.com>
2013-03-24 12:49:11 -04:00
Matt Porter
3ba65f97cb am33xx: refactor emif4/ddr to support multiple EMIF instances
The AM33xx emif4/ddr support closely matches what is need to support
TI814x except that TI814x has two EMIF instances. Refactor all the
emif4 helper calls and the config_ddr() init function to use an
additional instance number argument.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:11 -04:00
Matt Porter
81df2bab46 am33xx: convert defines from am33xx-specific to generic names
Eliminate AM33xx specific names to prepare for TI814x support
within AM33xx-land.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:11 -04:00
Tom Rini
98f92001b3 am33xx: Add required includes to some omap/am33xx code
- In arch/arm/cpu/armv7/omap-common/timer.c,
  drivers/mtd/nand/omap_gpmc.c and drivers/net/cpsw.c add #include files
  that the driver needs but had been relying on <config.h> to bring in.
- In arch/arm/cpu/armv7/omap-common/lowlevel_init.S add <config.h>
- In am335x_evm.h and pcm051.h don't globally include
  <asm/arch/hardware.h> and <asm/arch/cpu.h> but just <asm/arch/omap.h>
  as that is the only include which defines things the config uses.

Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:11 -04:00
Vaibhav Hiremath
59dcf970d1 am335x: Enable DDR PHY dynamic power down bit for DDR3 boards
Enable DDR PHY dynamic power down bit, which enables
powering down the IO receiver when not performing read.

This also helps in reducing overall power consumption in
low power states (suspend/standby).

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:05 -04:00
Mark Jackson
fc33705e66 Allow AM335x MPU core clock speed to be specified in the board config file
Allow AM335x MPU core clock speed to be specified in the board config file.
To use, add the following to the board's config file:-

#define CONFIG_SYS_MPUCLK	<desired clock freq in MHz>

Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
2013-03-22 10:57:00 -04:00
Mark Jackson
6b3dcc45c4 Allow AM33xx boards to setup GPMC chipselects.
Expose the enable_gpmc_cs_config() function so AM33xx based boards can register GPMC chip selects.

Changes in V4:
- Fix checkpatch errors (TAB -> space mangling)

Changes in V3:
- Fix line wrapping

Changes in V2:
- Indicate this is for AM33xx (not OMAP2)

Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
2013-03-11 11:06:08 -04:00
Nikita Kiryanov
fa3a69289f omap: consolidate common mmc definitions
The various mmc_host_def.h files are almost identical.
Reduce code duplication by moving the similar definitions to a common
header file.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-08 16:41:12 -05:00
Ilya Yanok
da07c21b77 am33xx: support for booting via usbeth
This patch adds BOOT_DEVICE define for USB booting and fixes
spl_board_init function to call arch_misc_init (this is the place there
musb is initialized).

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2013-02-18 13:48:04 -05:00
Jeff Lance
13526f7157 Add DDR3 support for AM335x-EVM (Version 1.5A)
AM335x EVM 1.5A uses Micron MT41J512M8RH-125 SDRAM 4Gb (512Mx8) as the
DDR3 chip.

[Hebbar Gururaja <gururaja.hebbar@ti.com>]
	- Resolve merge conflict while rebasing. File structure is
	  changed in the mainline. So re-arrange the code accordingly.
	- Update commit message to reflect the DDR3 part number

Signed-off-by: Jeff Lance <j-lance1@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
2013-02-07 10:36:26 -05:00
Lars Poeschel
1c1b7c3739 pcm051: Add support for Phytec phyCORE-AM335x
The board is named pcm051 and has this hardware:
SOC: TI AM3359
DDR3-RAM: 2x MT41J256M8HX-15EIT:D 512MiB
ETH 1: LAN8710AI
SPI-Flash: W25Q64BVSSIG
RTC: RV-4162-C7
I2C-EEPROM: CAT32WC32
NAND: MT29F4G08_VFPGA63
PMIC: TPS65910A3
LCD

Supported:
UART 1
MMC/SD
ETH 1
USB
I2C
SPI

Not yet supported:
NAND
RTC
LCD

Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
[trini: Add #define CONFIG_PHY_ADDR 0 to config]
Signed-off-by: Tom Rini <trini@ti.com>
2013-02-07 10:36:26 -05:00
Lars Poeschel
aca0b8b4f7 am33xx: add a pulldown macro to pinmux config
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
2013-02-07 10:36:25 -05:00
Albert ARIBAUD
79f3877794 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'
This required manual merging drivers/mtd/nand/Makefile
and adding am335x_evm support for CONFIG_SPL_NAND_DRIVERS
2013-01-08 13:15:45 +01:00
Mansoor Ahamed
04c3757829 am33xx: add ELM support
AM33XX has Error Location Module (ELM) that can be used in conjuction
with GPMC controller to implement BCH codes fully in hardware.
This code is mostly taken from arago tree.

Signed-off-by: Mansoor Ahamed <mansoor.ahamed@ti.com>
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10 08:54:02 -07:00
Ilya Yanok
8eb16b7f73 am33xx: NAND support
TI AM33XX has the same GPMC controller as OMAP3 so we could just use the
existing omap_gpmc driver. This patch adds adds required
definitions/intialization.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10 08:54:01 -07:00
Ilya Yanok
7df5cf35de am33xx: init OTG hardware and new musb gadget driver
AM33xx has support for dual port MUSB OTG controller. This patch
adds initialization for the controller using new MUSB gadget
driver and ether gadget.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20 00:16:07 +01:00
Peter Korsgaard
c7d35bef25 am33xx/ddr_defs.h: rename DDR2/DDR3 defines to their actual part numbers
So other parts can be added.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25 11:31:38 -07:00
Peter Korsgaard
c00f69dbcd am33xx: support board specific ddr settings
Move the hardcoded ddr2/ddr3 settings for the ti boards to board code,
so other boards can use different types/timings.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make apply with rtc32k_enable() in the file]
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25 11:31:38 -07:00
Peter Korsgaard
7f26a5a26f am33xx: move generic parts of pinmux handling out from board/ti/am335x
So they are available for other boards.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25 11:31:37 -07:00
Peter Korsgaard
e363426e99 am33xx: move ti i2c baseboard header handling to board/ti/am335x/
The i2c header is specific to ti(-derived) boards, and not generic for all
am335x boards.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make re-apply with rtc32k_enable() applied]
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25 11:31:36 -07:00
Tom Rini
69916bcf71 am33xx: Add SPI SPL as an option
Add the required config.mk logic for this SoC as well as the BOOT_DEVICE
define.  Finally, enable the options on the am335x_evm.

Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25 11:30:50 -07:00
Vaibhav Hiremath
000820b583 am335x: Enable RTC 32K OSC clock
In order to support low power state, you must source kernel system
timers to persistent clock, available across suspend/resume.  In case of
AM335x device, the only source we have is, RTC32K, available in
wakeup/always-on domain.  Having said that, during validation it has
been observed that, RTC clock need couple of seconds delay to stabilize
the RTC OSC clock; and such a huge delay is not acceptable in kernel
especially during early init and also it will impact quick/fast boot
use-cases.

So, RTC32k OSC enable dependency has been shifted to
SPL/first-bootloader.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25 11:30:22 -07:00
Joel A Fernandes
90207b6268 am33xx: Fix fetching of mmc1 bootmode from bootrom for AM33XX
U-boot should not ignore getting the bootmode passed on from the bootrom.
With this, U-boot SPL knows it was loaded from MMC1 and use this info to
read full U-boot from MMC1 as well.

Cc: pprakash@ti.com
Cc: trini@ti.com
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-01 10:02:15 -07:00
Ilya Yanok
7ac2fe2da2 OMAP: networking support for SPL
This patch adds support for networking in SPL. Some devices are
capable of loading SPL via network so it makes sense to load the
main U-Boot binary via network too. This patch tries to use
existing network code as much as possible. Unfortunately, it depends
on environment which in turn depends on other code so SPL size
is increased significantly. No effort was done to decouple network
code and environment so far.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-01 10:02:14 -07:00
Tom Rini
55cdbb8d4e ARM: SPL: Add <asm/spl.h> and <asm/arch/spl.h>
Move the SPL prototypes from <asm/omap_common.h> into <asm/spl.h> and
add <asm/arch/spl.h> for arch specific portions of CONFIG_SPL_FRAMEWORK.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:57 -07:00
Satyanarayana, Sandhya
6995a28937 am33xx evm: Update secure_emif_sdram_config during ddr init
This patch updates secure_emif_sdram_config with the
same value written to sdram_config during ddr3 initialization.

During suspend/resume, this value is copied into sdram_config.
With this, a write to sdram_config at the end of resume sequence
which triggers an init sequence can be avoided.

Without this register write in place, the DDR_RESET line goes
low for a few cycles during resume which is a violation of the
JEDEC spec.

Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
2012-09-01 14:58:19 +02:00
Tom Rini
41aebf8106 omap4/5/am33xx: Make lowlevel_init available to all armv7 platforms
Make the lowlevel_init function that these platforms have which just
sets up the stack and calls a C function available to all armv7
platforms.  As part of this we change some of the macros that are used
to be more clear.  Previously (except for am335x evm) we had been
setting CONFIG_SYS_INIT_SP_ADDR to a series of new defines that are
equivalent to simply referencing NON_SECURE_SRAM_END.  On am335x evm we
should have been doing this initially and do now.

Cc: Sricharan R <r.sricharan@ti.com>
Tested-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:19 +02:00
Tom Rini
0689a2ef19 am33xx: Correct MMC1, remove MMC2 support
- Correct the MMC1 base offset
- Remove MMC2 (that area is reserved and not MMC2).
- Add the real BOOT_DEVICE_MMC2 value

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:18 +02:00
Tom Rini
db7dd8109c am33xx: Rework pinmux functions
- Move definition of the EEPROM contents to <asm/arch/sys_proto.h>
  - Make some defines a little less generic now.
- Pinmux must be done by done by SPL now.
- Create 3 pinmux functions, uart0, i2c0 and board.
- Add pinmux specific to Starter Kit EVM for MMC now.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
65d750be59 am33xx: Add support for TI AM335x StarterKit EVM
- Board requires gpio0 #7 to be set to power DDR3.
- Board uses DDR3, add a way to determine which DDR type to call
  config_ddr with.
- Both of the above require filling in the header structure early, move
  it into the data section.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
d4898ea896 am33xx: Add DDR3 (Micron MT41J128M16JT-125) timings and support
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
a74f0c7cb5 am33xx: Correct and clean up ddr_regs struct
The ddr_regs struct was incorrectly offset after the dt0wiratio0 entry.
Correct this by documenting a missing register that will be used at some
point in the future (when write leveling is supported).  Further, the
cmdNcs{force,delay} fields are undocumented and we have been setting
them to zero, remove.  Next, setting of the
'DATAn_REG_PHY_USE_RANK0_DELAYS field belongs with the rest of the
ddr_data entries, so program it there.  Finally, comment on how we are
configuring the DATA1 registers that correspond to the DATA0 (dt0)
registers defined in the struct.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00