This function only returns an error message sometimes. Update it to always
return an error message if one is available. This makes it easier to see
what went wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be a little more specific about what is being checked.
Update a few messages to help with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The core and vdd PMIC buck regulators were misconfigured, which caused
instability of the board and malfunction of high-speed interfaces, like
the RGMII. Configure the PMIC correctly to repair these problems. Also,
model the missing Enpirion EP53A8LQI on the DHCOR SoM as a fixed regulator.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The AV96 RGMII uses different pinmux for ETH_RGMII_TXD0, ETH_RGMII_RXD2
and ETH_RGMII_TX_CTL. Use the correct pinmux to make ethernet operational.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add another mux option for DWMAC RGMII, this is used on AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The board has an EEPROM on the same I2C bus as PMIC, at address 0x53.
The EEPROM contains the board MAC address.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: I340a0675c11e4599968b2e3ef0515fb8da8d7b42
Use DT /aliases node to establish a stable phandle to the configuration
EEPROM. This permits the configuration EEPROM to be moved e.g. to a
different address or a different bus. Adjust the board code to handle
new phandle lookup.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The DH Electronics DHCOR SOM has QSPI NOR on the SoM itself, add it
into the DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Ia7c454c496f50e3fc4851ec1154f3641c416e98e
The eMMC uses different pinmux for the top four data lines, use such
a pinmux, otherwise it takes a very long time until the test for 8bit
operation times out. And this is the correct pinmux per schematic too.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add another mux option for SDMMC2 pins 4..7, this is used on AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The SD uses different pinmux for the D123DIRline, use such a pinmux,
otherwise there is a pinmux collision on the AV96. Add missing SD
voltage regulator switch and enable SDR104 operation.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add another mux option for SDMMC1 direction pins, in particular
SDMMC1_D123DIR, this is used on AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The sdmmc1_dir_pins_a: sdmmc1-dir-0 layout changed in commit 35a54d41d9
("ARM: dts: stm32mp1: sync device tree with v5.2-rc4") such that pins{};
became pins1{};pins2{};, however the SPL extras were not updated to reflect
that change. Fix this.
This fixes booting from SD1 X9 slot on the AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Fixes: 35a54d41d9 ("ARM: dts: stm32mp1: sync device tree with v5.2-rc4")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
This last minute pull-request is intended to fix some drivers
when used on ARC boards. The problem was introduced by
07906b3dad
What happened while doing one pretty simple improvement to make
U-Boot port more flexible and portable (by switching accessors from
assembly-written to plain C version) we implicitly added 2 problems:
1. Downgraded accessors from being volatile which signalled to
the compiler that it's now possible to do all kinds of optimizations
which may easily include merge of subsequent byte reads/writes into
word operations. Which is OK for accessing mormal memory but
breaks operation of peripherals if we access its memory-mapped regs
in such a "creative" manner.
2. As a part of assembly-written implementation we had compiler barriers
in form of the following construction 'asm volatile("" : : : "memory")',
and we dropped it in C implemntation. This in its turn enabled compiler
to mess with instruction ordering. Guess what it gives us in the end :)
So with all that we had in some corner-cases veeery funny instruction flows
generated. And in particular it broke DW SPI functionality when we were
writing large amount of data. Funny enough our tests which were writing
small amount of data still worked and only by the chance we caught that
breakage and unrolled that quite interesting loop of unexpected
problems.
The road to hell is paved with good intentions. Amen :)
We add memory barriers for __raw_readX / __raw_writeX accessors same
way as it is done for readX and writeX accessors as lots of U-boot
driver uses __raw_readX / __raw_writeX instead of proper accessor
with barrier.
It will save us from lot's of debugging in the future and it is OK
as U-Boot is not that performance oriented as real run-time
software like OS or user bare-metal app so we may afford being not
super fast as we only being executed once.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We must use compiler barriers in C-version read/write IO accessors
before and after operation (read or write) so it won't be reordered
by compiler.
Fixes commit 07906b3dad ("ARC: Switch to generic accessors")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We must use 'volatile' in C-version read/write IO accessors
implementation to avoid merging several reads (writes) into
one read (write), or optimizing them out by compiler.
Fixes commit 07906b3dad ("ARC: Switch to generic accessors")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
When MACB_ZYNQ is enabled there is compilation warnings
drivers/net/macb.c: In function ‘_macb_init’:
drivers/net/macb.h:675:33: error: ‘MACB_DMACFG’ undeclared (first use in this function);
did you mean ‘MACB_MCF’?
writel((value), (port)->regs + MACB_##reg)
^~~~~
It has been caused by changing macros name by commit below.
Fixes: 6c636514d4 ("net: macb: sync header definitions as taken from Linux")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Not all boards have the same CSB frequency, nor do every SPI slave
necessarily support running at 16.7 MHz. So implement ->set_speed;
that also allows using a smaller PM (i.e., 0) for slaves that do
support a higher speed.
Based on work by Klaus H. Sørensen.
Cc: Klaus H. Sorensen <khso@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
There are a few problems with the current driver.
First, it unconditionally reads from dout/writes to din whether or not
those pointers are NULL. So for example a simple "sf probe" ends up
writing four bytes at address 0:
=> md.l 0x0 8
00000000: 45454545 45454545 05050505 05050505 EEEEEEEE........
00000010: 00000000 00000000 07070707 07070707 ................
=> sf probe 0
mpc8xxx_spi_xfer: slave spi@7000:0 dout 0FB53618 din 00000000 bitlen 8
mpc8xxx_spi_xfer: slave spi@7000:0 dout 00000000 din 0FB536B8 bitlen 48
SF: Detected s25sl032p with page size 256 Bytes, erase size 64 KiB, total 4 MiB
=> md.l 0x0 8
00000000: ff000000 45454545 05050505 05050505 ....EEEE........
00000010: 00000000 00000000 07070707 07070707 ................
(here I've change the first debug statement to a printf, and made it
print the din/dout pointers rather than the uints they point at).
Second, as we can also see above, it always writes a full 32 bits,
even if a smaller amount was requested. So for example
=> mw.l $loadaddr 0xaabbccdd 8
=> md.l $loadaddr 8
02000000: aabbccdd aabbccdd aabbccdd aabbccdd ................
02000010: aabbccdd aabbccdd aabbccdd aabbccdd ................
=> sf read $loadaddr 0x400 6
device 0 offset 0x400, size 0x6
mpc8xxx_spi_xfer: slave spi@7000:0 dout 0FB536E8 din 00000000 bitlen 40
mpc8xxx_spi_xfer: slave spi@7000:0 dout 00000000 din 02000000 bitlen 48
SF: 6 bytes @ 0x400 Read: OK
=> sf read 0x02000010 0x400 8
device 0 offset 0x400, size 0x8
mpc8xxx_spi_xfer: slave spi@7000:0 dout 0FB53848 din 00000000 bitlen 40
mpc8xxx_spi_xfer: slave spi@7000:0 dout 00000000 din 02000010 bitlen 64
SF: 8 bytes @ 0x400 Read: OK
=> md.l $loadaddr 8
02000000: 45454545 45450000 aabbccdd aabbccdd EEEEEE..........
02000010: 45454545 45454545 aabbccdd aabbccdd EEEEEEEE........
Finally, when the bitlen is 24 mod 32 (e.g. requesting to read 3 or 7
bytes), the last three bytes and up being the wrong ones, since the
driver does a full 32 bit read and then shifts the wrong byte out:
=> mw.l $loadaddr 0xaabbccdd 4
=> md.l $loadaddr 4
02000000: aabbccdd aabbccdd aabbccdd aabbccdd ................
=> sf read $loadaddr 0x444 10
device 0 offset 0x444, size 0x10
mpc8xxx_spi_xfer: slave spi@7000:0 dout 0FB536E8 din 00000000 bitlen 40
mpc8xxx_spi_xfer: slave spi@7000:0 dout 00000000 din 02000000 bitlen 128
SF: 16 bytes @ 0x444 Read: OK
=> md.l $loadaddr 4
02000000: 552d426f 6f742032 3031392e 30342d30 U-Boot 2019.04-0
=> mw.l $loadaddr 0xaabbccdd 4
=> sf read $loadaddr 0x444 0xb
device 0 offset 0x444, size 0xb
mpc8xxx_spi_xfer: slave spi@7000:0 dout 0FB536E8 din 00000000 bitlen 40
mpc8xxx_spi_xfer: slave spi@7000:0 dout 00000000 din 02000000 bitlen 88
SF: 11 bytes @ 0x444 Read: OK
=> md.l $loadaddr 4
02000000: 552d426f 6f742032 31392e00 aabbccdd U-Boot 219......
Fix all of that by always using a character size of 8, and reject
transfers that are not a whole number of bytes. While it ends being
more work for the CPU, we're mostly bounded by the speed of the SPI
bus, and we avoid writing to the mode register in every loop.
Based on work by Klaus H. Sørensen.
Cc: Klaus H. Sorensen <khso@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Currently, max_cs is write-only; it's just set in
mpc8xxx_spi_ofdata_to_platdata and not otherwise used.
My mpc8309 was always resetting during an "sf probe 0". It turns out
dm_gpio_set_dir_flags() was being called with garbage, since nothing
had initialized priv->gpios[0] - our device tree used "cs-gpios"
rather than "gpios", so gpio_request_list_by_name() had returned 0.
That would have been a lot easier to figure out if the chip select
index was sanity checked, so rename max_cs to cs_count, and reject a
xfer with a too large cs index.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Some SoCs in the mpc83xx family, e.g. mpc8309, have a dedicated spi
chip select, SPISEL_BOOT, that is used by the boot code to boot from
flash.
This chip select will typically be used to select a SPI boot
flash. The SPISEL_BOOT signal is controlled by a single bit in the
SPI_CS register.
Implement a gpio driver for the spi chip select register. This allows a
spi driver capable of using gpios as chip select, to bind a chip select
to SPISEL_BOOT.
It may be a little odd to do this as a GPIO driver, since the signal
is neither GP or I, but it is quite convenient to present it to the
spi driver that way. The alternative it to teach mpc8xxx_spi to handle
the SPISEL_BOOT signal itself (that is how it's done in the linux
kernel, see commit 69b921acae8a)
Signed-off-by: Klaus H. Sorensen <khso@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The driver correctly handles reading back the value of an output gpio
by reading from the shadow register for output, and from gpdat for
inputs.
Unfortunately, when setting the value of some gpio, we do a RMW cycle
on the gpdat register without taking the shadow register into account,
thus accidentally setting other output gpios (at least those whose
value cannot be read back) to 0 at the same time.
When changing a gpio from input to output, we still need to make sure
it initially has the requested value. So, the procedure is
- update the shadow register
- compute the new gpdir register
- write the bitwise and of the shadow and new gpdir register to gpdat
- write the new gpdir register
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Since some chips don't support reading back the value of output gpios
from the gpdat register, we should not do a RMW cycle (i.e., the
clrbits_be32) on the gpdat register when setting a gpio as input, as
that might accidentally change the value of some other (still
configured as output) gpio.
The extra indirection through mpc8xxx_gpio_set_in() does not help
readability, so just fold the gpdir update into
mpc8xxx_gpio_direction_input().
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
This adds the check against IH_OS_VXWORKS during FIT image load,
to allow loading FIT image for VxWorks.
Signed-off-by: Lihua Zhao <lihua.zhao@windriver.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This series fixes:
* UEFI Python tests CONFIG_OF_CONTROL=y.
* int to pointer cast warning for cmd/efidebug.c
* memory reservation even if fdt node is disabled
Now that the Python test is fixed reintroduce the reverted patch for
vexpress_ca9x4 to enable EFI_LOADER and define the dtb file name.
-----BEGIN PGP SIGNATURE-----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=Cgg0
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-04-rc5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc5
This series fixes:
* UEFI Python tests CONFIG_OF_CONTROL=y.
* int to pointer cast warning for cmd/efidebug.c
* memory reservation even if fdt node is disabled
Now that the Python test is fixed reintroduce the reverted patch for
vexpress_ca9x4 to enable EFI_LOADER and define the dtb file name.
Add save_boot_params() to save reset status value from bootrom.
Bootrom will clear the status register in reset manager and stores the
reset status value in shared memory. Bootrom stores shared data at last
2KB of onchip RAM.
This function save reset status provided by bootrom to rst_mgr_status.
More information about reset status register value can be found in reset
manager register description.
When running in debugger without bootrom, r0 to r3 are random values.
So, skip save the value when r0 is not bootrom shared data address.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
With CONFIG_OF_CONTROL environment variable $fdtcontroladdr is not defined
and test_efi_grub_net() fails.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If the DM_ETH is enabled, the board-specific ethernet registeration
should be disabled, make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add code to reset the board through PMIC, by writing the required
PMIC registers in the CPU reset handler.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Configure RX and TX bus-width values to use flexspi in octal I/O mode.
If bus-widths are not specified, then single I/O mode is set by default.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Configure RX and TX bus-width values to use flexspi in octal I/O mode.
If bus-widths are not specified, then single I/O mode is set by default.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
MC_INIT and BOOT command currently access spi-nor flash memory directly.
As per spi-mem framework, flash memory access via absolute addresses is
no more possible. Use flash APIs to access memory instead of directly
using it.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_ENV_ADDR helps in picking environment from flash before DDR init.
Define the value as 0x20500000 for lx2160ardb and lx2160aqds.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable FSPI controller support. So, flash environment can now be used.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
