Commit graph

178 commits

Author SHA1 Message Date
Enric Balletbo i Serra
cc175e6353 Add DDR3 support for IGEP COM AQUILA/CYGNUS.
These boards uses Samsung K4B2G1646E-BIH9 a 2Gb E-die DDR3 SDRAM.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-05-10 08:25:55 -04:00
Matt Porter
035d563937 am33xx: add pll and clock support for TI814x CPSW
Enables required PLLs and clocks for CPSW on TI814x.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-05-10 08:25:54 -04:00
Tom Rini
86fdb1619a am335x: Really correct DDR timings on new BeagleBone part
The previous timings were done on the internal-only A1 board which has
different DDR part than all later revs.  The timings need a slight
adjustment to be correct in all cases with later revs.

Signed-off-by: Tom Rini <trini@ti.com>
2013-04-12 12:38:16 -04:00
Tom Rini
b996a3e9a8 am335x: Update timings for the beaglebone again
After further testing we can run DDR at 400MHz so update the timings
again.

Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tom Rini <trini@ti.com>
2013-04-10 10:04:40 -04:00
Tom Rini
74f40ea1bc am335x/ti814x: Correct MMC_BOOT_DEVICES_START/END
Given that on TI814x we have MMC1/2 swapped, we also need to swap them
in MMC_BOOT_DEVICES_START/END

Reported-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
2013-04-09 11:40:40 -04:00
Tom Rini
c3d2c24f6c OMAP3/4/5/AM33xx: Correct logic for checking FAT or RAW MMC
In the case of booting from certain peripherals, such as UART, we must
not see what the device descriptor says for RAW or FAT mode because in
addition to being nonsensical, it leads to a hang.  This is why we have
a test currently for the boot mode being within range.  The problem
however is that on some platforms we get MMC2_2 as the boot mode and not
the defined value for MMC2, and in others we get the value for MMC2_2.
This is required to fix eMMC booting on omap5_uevm.

Tested on am335x_evm (UART, NAND, SD), omap3_beagle (NAND, SD on
classic, SD only on xM rev C5) and omap5_uevm (SD, eMMC).

Signed-off-by: Tom Rini <trini@ti.com>
2013-04-08 11:29:34 -04:00
Andreas Bießmann
da634ae356 omap_gpmc: change nandecc command
With uppcoming BCH support on OMAP devices we need to decide between differnt
algorithms when switching the ECC engine.  Currently we support 1-bit hammign
and 8-bit BCH on HW backend.

In order to switch between differnet ECC algorithms we need to change the
interface of omap_nand_switch_ecc() also.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Thomas Weber <thomas.weber.linux@googlemail.com>
2013-04-08 11:29:05 -04:00
Andreas Bießmann
5bf299bc4f asm/omap_gpmc.h: consolidate common defines
arch/arm/include/asm/arch-am33xx/omap_gpmc.h and
arch/arm/include/asm/arch-omap3/omap_gpmc.h are almost the same, consolidate
the common parts into a new header.

Introduce a new asm/omap_gpmc.h which defines the command part and pulls in
the architecture specific one.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-08 11:29:05 -04:00
Tom Rini
c7ba18ad4b am335x_evm: Add better timings for the new BeagleBoard DDR3 part
Tested-by: Rao Bodapati <rao@circuitco.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:12 -04:00
Matt Porter
26fa57842b am33xx: support ti814x mmc reference clock
TI814x has a 192MHz hsmmc reference clock. Select that clock rate
when building for TI814x.

Signed-off-by: Matt Porter <mporter@ti.com>
2013-03-24 12:49:11 -04:00
Matt Porter
4fab8d7bbd am33xx: add dmm support to emif4 library
Adds a config_dmm() routine to support TI814X DMM configuration.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:11 -04:00
Matt Porter
8b029f22a6 am33xx: add ti814x specific register definitions
Support the ti814x specific register definitions within
arch-am33xx.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:11 -04:00
Matt Porter
b2e682f7a0 am33xx: refactor am33xx mux support and add ti814x support
AM33XX and TI814X have a similar mux though the pinmux register
layout and address space differ. Add a separate ti814x mux include
to support the TI814X-specific differences.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
2013-03-24 12:49:11 -04:00
Matt Porter
b43c17cba6 am33xx: refactor am33xx clocks and add ti814x support
Split clock.c for am335x and ti814x and add ti814x specific
clock support.

Signed-off-by: Matt Porter <mporter@ti.com>
2013-03-24 12:49:11 -04:00
Matt Porter
3ba65f97cb am33xx: refactor emif4/ddr to support multiple EMIF instances
The AM33xx emif4/ddr support closely matches what is need to support
TI814x except that TI814x has two EMIF instances. Refactor all the
emif4 helper calls and the config_ddr() init function to use an
additional instance number argument.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:11 -04:00
Matt Porter
81df2bab46 am33xx: convert defines from am33xx-specific to generic names
Eliminate AM33xx specific names to prepare for TI814x support
within AM33xx-land.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:11 -04:00
Tom Rini
98f92001b3 am33xx: Add required includes to some omap/am33xx code
- In arch/arm/cpu/armv7/omap-common/timer.c,
  drivers/mtd/nand/omap_gpmc.c and drivers/net/cpsw.c add #include files
  that the driver needs but had been relying on <config.h> to bring in.
- In arch/arm/cpu/armv7/omap-common/lowlevel_init.S add <config.h>
- In am335x_evm.h and pcm051.h don't globally include
  <asm/arch/hardware.h> and <asm/arch/cpu.h> but just <asm/arch/omap.h>
  as that is the only include which defines things the config uses.

Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:11 -04:00
Vaibhav Hiremath
59dcf970d1 am335x: Enable DDR PHY dynamic power down bit for DDR3 boards
Enable DDR PHY dynamic power down bit, which enables
powering down the IO receiver when not performing read.

This also helps in reducing overall power consumption in
low power states (suspend/standby).

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:05 -04:00
Mark Jackson
fc33705e66 Allow AM335x MPU core clock speed to be specified in the board config file
Allow AM335x MPU core clock speed to be specified in the board config file.
To use, add the following to the board's config file:-

#define CONFIG_SYS_MPUCLK	<desired clock freq in MHz>

Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
2013-03-22 10:57:00 -04:00
Mark Jackson
6b3dcc45c4 Allow AM33xx boards to setup GPMC chipselects.
Expose the enable_gpmc_cs_config() function so AM33xx based boards can register GPMC chip selects.

Changes in V4:
- Fix checkpatch errors (TAB -> space mangling)

Changes in V3:
- Fix line wrapping

Changes in V2:
- Indicate this is for AM33xx (not OMAP2)

Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
2013-03-11 11:06:08 -04:00
Nikita Kiryanov
fa3a69289f omap: consolidate common mmc definitions
The various mmc_host_def.h files are almost identical.
Reduce code duplication by moving the similar definitions to a common
header file.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-08 16:41:12 -05:00
Ilya Yanok
da07c21b77 am33xx: support for booting via usbeth
This patch adds BOOT_DEVICE define for USB booting and fixes
spl_board_init function to call arch_misc_init (this is the place there
musb is initialized).

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2013-02-18 13:48:04 -05:00
Jeff Lance
13526f7157 Add DDR3 support for AM335x-EVM (Version 1.5A)
AM335x EVM 1.5A uses Micron MT41J512M8RH-125 SDRAM 4Gb (512Mx8) as the
DDR3 chip.

[Hebbar Gururaja <gururaja.hebbar@ti.com>]
	- Resolve merge conflict while rebasing. File structure is
	  changed in the mainline. So re-arrange the code accordingly.
	- Update commit message to reflect the DDR3 part number

Signed-off-by: Jeff Lance <j-lance1@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
2013-02-07 10:36:26 -05:00
Lars Poeschel
1c1b7c3739 pcm051: Add support for Phytec phyCORE-AM335x
The board is named pcm051 and has this hardware:
SOC: TI AM3359
DDR3-RAM: 2x MT41J256M8HX-15EIT:D 512MiB
ETH 1: LAN8710AI
SPI-Flash: W25Q64BVSSIG
RTC: RV-4162-C7
I2C-EEPROM: CAT32WC32
NAND: MT29F4G08_VFPGA63
PMIC: TPS65910A3
LCD

Supported:
UART 1
MMC/SD
ETH 1
USB
I2C
SPI

Not yet supported:
NAND
RTC
LCD

Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
[trini: Add #define CONFIG_PHY_ADDR 0 to config]
Signed-off-by: Tom Rini <trini@ti.com>
2013-02-07 10:36:26 -05:00
Lars Poeschel
aca0b8b4f7 am33xx: add a pulldown macro to pinmux config
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
2013-02-07 10:36:25 -05:00
Albert ARIBAUD
79f3877794 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'
This required manual merging drivers/mtd/nand/Makefile
and adding am335x_evm support for CONFIG_SPL_NAND_DRIVERS
2013-01-08 13:15:45 +01:00
Mansoor Ahamed
04c3757829 am33xx: add ELM support
AM33XX has Error Location Module (ELM) that can be used in conjuction
with GPMC controller to implement BCH codes fully in hardware.
This code is mostly taken from arago tree.

Signed-off-by: Mansoor Ahamed <mansoor.ahamed@ti.com>
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10 08:54:02 -07:00
Ilya Yanok
8eb16b7f73 am33xx: NAND support
TI AM33XX has the same GPMC controller as OMAP3 so we could just use the
existing omap_gpmc driver. This patch adds adds required
definitions/intialization.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10 08:54:01 -07:00
Ilya Yanok
7df5cf35de am33xx: init OTG hardware and new musb gadget driver
AM33xx has support for dual port MUSB OTG controller. This patch
adds initialization for the controller using new MUSB gadget
driver and ether gadget.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20 00:16:07 +01:00
Peter Korsgaard
c7d35bef25 am33xx/ddr_defs.h: rename DDR2/DDR3 defines to their actual part numbers
So other parts can be added.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25 11:31:38 -07:00
Peter Korsgaard
c00f69dbcd am33xx: support board specific ddr settings
Move the hardcoded ddr2/ddr3 settings for the ti boards to board code,
so other boards can use different types/timings.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make apply with rtc32k_enable() in the file]
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25 11:31:38 -07:00
Peter Korsgaard
7f26a5a26f am33xx: move generic parts of pinmux handling out from board/ti/am335x
So they are available for other boards.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25 11:31:37 -07:00
Peter Korsgaard
e363426e99 am33xx: move ti i2c baseboard header handling to board/ti/am335x/
The i2c header is specific to ti(-derived) boards, and not generic for all
am335x boards.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make re-apply with rtc32k_enable() applied]
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25 11:31:36 -07:00
Tom Rini
69916bcf71 am33xx: Add SPI SPL as an option
Add the required config.mk logic for this SoC as well as the BOOT_DEVICE
define.  Finally, enable the options on the am335x_evm.

Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25 11:30:50 -07:00
Vaibhav Hiremath
000820b583 am335x: Enable RTC 32K OSC clock
In order to support low power state, you must source kernel system
timers to persistent clock, available across suspend/resume.  In case of
AM335x device, the only source we have is, RTC32K, available in
wakeup/always-on domain.  Having said that, during validation it has
been observed that, RTC clock need couple of seconds delay to stabilize
the RTC OSC clock; and such a huge delay is not acceptable in kernel
especially during early init and also it will impact quick/fast boot
use-cases.

So, RTC32k OSC enable dependency has been shifted to
SPL/first-bootloader.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25 11:30:22 -07:00
Joel A Fernandes
90207b6268 am33xx: Fix fetching of mmc1 bootmode from bootrom for AM33XX
U-boot should not ignore getting the bootmode passed on from the bootrom.
With this, U-boot SPL knows it was loaded from MMC1 and use this info to
read full U-boot from MMC1 as well.

Cc: pprakash@ti.com
Cc: trini@ti.com
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-01 10:02:15 -07:00
Ilya Yanok
7ac2fe2da2 OMAP: networking support for SPL
This patch adds support for networking in SPL. Some devices are
capable of loading SPL via network so it makes sense to load the
main U-Boot binary via network too. This patch tries to use
existing network code as much as possible. Unfortunately, it depends
on environment which in turn depends on other code so SPL size
is increased significantly. No effort was done to decouple network
code and environment so far.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-01 10:02:14 -07:00
Tom Rini
55cdbb8d4e ARM: SPL: Add <asm/spl.h> and <asm/arch/spl.h>
Move the SPL prototypes from <asm/omap_common.h> into <asm/spl.h> and
add <asm/arch/spl.h> for arch specific portions of CONFIG_SPL_FRAMEWORK.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:57 -07:00
Satyanarayana, Sandhya
6995a28937 am33xx evm: Update secure_emif_sdram_config during ddr init
This patch updates secure_emif_sdram_config with the
same value written to sdram_config during ddr3 initialization.

During suspend/resume, this value is copied into sdram_config.
With this, a write to sdram_config at the end of resume sequence
which triggers an init sequence can be avoided.

Without this register write in place, the DDR_RESET line goes
low for a few cycles during resume which is a violation of the
JEDEC spec.

Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
2012-09-01 14:58:19 +02:00
Tom Rini
41aebf8106 omap4/5/am33xx: Make lowlevel_init available to all armv7 platforms
Make the lowlevel_init function that these platforms have which just
sets up the stack and calls a C function available to all armv7
platforms.  As part of this we change some of the macros that are used
to be more clear.  Previously (except for am335x evm) we had been
setting CONFIG_SYS_INIT_SP_ADDR to a series of new defines that are
equivalent to simply referencing NON_SECURE_SRAM_END.  On am335x evm we
should have been doing this initially and do now.

Cc: Sricharan R <r.sricharan@ti.com>
Tested-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:19 +02:00
Tom Rini
0689a2ef19 am33xx: Correct MMC1, remove MMC2 support
- Correct the MMC1 base offset
- Remove MMC2 (that area is reserved and not MMC2).
- Add the real BOOT_DEVICE_MMC2 value

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:18 +02:00
Tom Rini
db7dd8109c am33xx: Rework pinmux functions
- Move definition of the EEPROM contents to <asm/arch/sys_proto.h>
  - Make some defines a little less generic now.
- Pinmux must be done by done by SPL now.
- Create 3 pinmux functions, uart0, i2c0 and board.
- Add pinmux specific to Starter Kit EVM for MMC now.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
65d750be59 am33xx: Add support for TI AM335x StarterKit EVM
- Board requires gpio0 #7 to be set to power DDR3.
- Board uses DDR3, add a way to determine which DDR type to call
  config_ddr with.
- Both of the above require filling in the header structure early, move
  it into the data section.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
d4898ea896 am33xx: Add DDR3 (Micron MT41J128M16JT-125) timings and support
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
a74f0c7cb5 am33xx: Correct and clean up ddr_regs struct
The ddr_regs struct was incorrectly offset after the dt0wiratio0 entry.
Correct this by documenting a missing register that will be used at some
point in the future (when write leveling is supported).  Further, the
cmdNcs{force,delay} fields are undocumented and we have been setting
them to zero, remove.  Next, setting of the
'DATAn_REG_PHY_USE_RANK0_DELAYS field belongs with the rest of the
ddr_data entries, so program it there.  Finally, comment on how we are
configuring the DATA1 registers that correspond to the DATA0 (dt0)
registers defined in the struct.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
82afcc9efd am33xx: Do not touch 'ratio1' fields
The various ratio1 fields are not documented in any of the documentation
I can find.  Removing these and testing has yielded success, so remove
the code that sets them and move their locations into the reserved
fields.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
5ac3b7ada1 am33xx: Rework config_io_ctrl slightly
This function sets a number of related registers to the same value (the
registers in question all have the same field descriptions and are
related in operation).  Rather than defining a struct and setting the
value repeatedly, just pass in the value.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
ff7ec0f945 am33xx: Use emif_regs struct for storing initialization values
Rather than defining our own structs to note what to use when
programming the EMIF and related re-use the emif_regs struct.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
87a1acbb69 am33xx: Turn a number of 'int' functions to 'void'
A number of memory initalization functions were int and always returned
0.  Further it's not feasible to be doing error checking here, so simply
turn them into void functions.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
c48c895433 am33xx: Document what we're doing with ddrctrl->ddrckectrl
- Remove the call to set ddrctrl->ddrioctrl as it's all zeros.
- Comment what we're really setting in ddrctrl->ddrckectrl which is that
  we're operating in the normal mode where EMIF/PHY clock is controlled
  by the PHY.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Vaibhav Bedia
7d8a961d31 am335x: ddr_defs: Update EMIF parameters
EMIF parameters are calculated based on the AC timing
parameters from the SDRAM datasheet and the DDR frequency.

Current values for these paramters in AM335x U-Boot code,
though reliable, are not fully optimal. The most optimal
settings can be derived based on the guidelines published
at [1]. A pre-computed set of values with the most optimum
settings for AM335x EVM and BeagleBone can be found at [2].

[1] http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips
[2] http://processors.wiki.ti.com/index.php/OMAP_and_Sitara_CCS_support#AM335x

Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
c8da4a587c am33xx: Clean up unused DDR defines, prefix more with 'DDR2'
- Remove a handful of unused defines.
- Prefix more values with 'DDR2' as DDR3 will require different values.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
b971dfad6a am33xx: Move the call to ddr_pll_config, make it take the frequency
Depending on if we have DDR2 or DDR3 on the board we will need to call
ddr_pll_config with a different value.  This call can be delayed
slightly to the point where we know which type of memory we have.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
fda35eb982 am33xx: Pass to config_ddr the type of memory that is connected
We need to pass in the type of memory that is connected to the board.
The only reliable way to do this is to know what type of board we are
running on (which later will be knowable in s_init()).  For now, pass in
the value of DDR2.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
bce58fece5 am33xx: Make config_cmd_ctrl / config_ddr_data take const structs
Rework the EMIF4/DDR code slightly to setup the structs that
config_cmd_ctrl and config_ddr_data take to be setup at compile time and
mark them as const.  This lets us simplify the calling path slightly as
well as making it easier to deal with DDR3.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
7d5eb34908 am33xx: Convert to using <asm/emif.h> to describe the EMIF
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:11 +02:00
Tom Rini
79b3e6b75b am33xx: Remove DMM_BASE define
The am33xx does not have a DMM, so don't define the base.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:11 +02:00
Chandan Nath
89017e150e am33xx: pin mux defintions for CPSW switch
This patch adds pin mux settings for CPSW switch found on
TI AM335X based boards (MII and RGMII modes).

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split pinmux into separate patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01 14:58:11 +02:00
Chandan Nath
e79cd8eb9b am33xx: CPSW init and definitions
This patch adds platform-specific initialization for CPSW
switch on TI AM33XX SoCs.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split init out of original patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01 14:58:11 +02:00
Steve Sakoman
3b97152b63 omap: am33xx: enable gpio support
This patch uses the code in omap-common to support gpio modules 1-3
on am33xx based boards.

It adds base address and register definitions, enables clocks to the
modules, and enables building the common gpio code for CONFIG_AM33XX
as well as CONFIG_OMAP

Signed-off-by: Steve Sakoman <steve@sakoman.com>
2012-09-01 14:58:09 +02:00
Steve Sakoman
f2b37a6533 omap: am33xx: accomodate input clocks other than 24 Mhz
The PLL setup values currently assume a 24 Mhz input clock.

This patch uses V_OSCK from the board config file to support boards
with different input clock rates.

Signed-off-by: Steve Sakoman <steve@sakoman.com>
2012-07-07 14:07:35 +02:00
Lokesh Vutla
702395073f ARM: OMAP3+: Detect reset type
Certain modules are not affected by means of
a warm reset and need not be configured again.
Adding an API to detect the reset reason warm/cold.

This will be used to skip the module configurations
that are retained across a warm reset.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-07-07 14:07:34 +02:00
Tom Rini
65c206b688 am33xx: Fix i2c sampling rate typo
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
2012-07-07 14:07:22 +02:00
Tom Rini
d88bc0425b am33xx: Fill in more cm_wkuppll / cm_perpll
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
2012-07-07 14:07:22 +02:00
Tom Rini
fe4f97b98f am335x: Correct i2c sysc offset
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
2012-07-07 14:07:22 +02:00
Tom Rini
2ab2810375 am33xx: Do not call init_timer twice
We do not need to call init_timer both in SPL and U-Boot itself, just
SPL needs to initialize the timer.

Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07 14:07:21 +02:00
Jonathan Solnit
bbbc1ae921 ARM:OMAP+:MMC: Add parameters to MMC init
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency.  While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board.  The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.

Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
2012-05-15 08:31:22 +02:00
Chase Maupin
0e35bde7b1 am33xx: ddr_defs.h: Change DDR timings
* For cold silicon the DDR timings need to be relaxed in order for
  the device to boot with DDR at 266MHz
* Fix proposed by James Doublesin

Signed-off-by: Chase Maupin <Chase.Maupin@ti.com>
2012-02-27 21:19:24 +01:00
Tom Rini
a7778f8fbe omap_hsmmc: Wait for CMDI to be clear
Before we can send a command we need both the DATI (command inhibit on
mmc_dat line) bit and CMDI (command inhibit on mmc_cmd line) are clear.
The previous behavior of only checking on DATI was insufficient on some
cards and incorrect behavior in any case.  This makes the code check
for both bits being clear and makes the error print more clear as
to what happened.  DATI_CMDDIS is removed as it was unused elsewhere
in the code and stood for 'DATI is set, cmds are disabled still'.

Fix originally spotted by Peter Bigot.

Tested-by: Peter A. Bigot <bigotp@acm.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Andreas Müller <schnitzeltony@googlemail.com>
2012-02-15 17:42:22 -06:00
Patil, Rachna
b4116ede36 ARM: AM33XX: Add i2c support
Add i2c driver board hookup for AM335X EVM

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Patil, Rachna <rachna@ti.com>
2012-01-23 11:57:31 +01:00
Chandan Nath
8a8f084e4f ARM:AM33XX: Add SPL support for AM335X EVM
This patch is added to support SPL feature on AM335X
platform. In this patch, MMC1 is configured as boot
device for SPL and support for other devices will be
added in the next patch series.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16 08:40:12 +01:00
Chandan Nath
876bdd6d46 ARM:AM33XX: Add mmc/sd support
This patch add supports for mmc/sd driver on AM335X platform.
PLL and pinmux configurations for mmc/sd are configured in this
patch.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16 08:40:12 +01:00
Chandan Nath
fb072a3ead ARM:AM33XX: Fix ddr and timer register offset
This patch is added to update incorrect ddr and timer
register offset.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16 08:40:11 +01:00
Chandan Nath
f16da7466f ARM:AM33XX: Replace CONFIG_AM335X with CONFIG_AM33XX
This patch is added to replace CONFIG_AM335X symbol
with CONFIG_AM333XX for AM33XX platforms.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Thomas Weber <weber@corscience.de>
2012-01-16 08:40:11 +01:00
Tom Rini
35b541c835 am335x: Drop board_sysinfo struct
This isn't used presumably should be a typedef if needed later.

Signed-off-by: Tom Rini <trini@ti.com>
2011-11-03 22:56:21 +01:00
Chandan Nath
62d7fe7c91 ARM:AM33XX: Add emif/ddr support
This patch adds AM33xx emif/ddr support along with board specific
defines.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:36 +02:00
Chandan Nath
f87fa62af9 ARM:AM33XX: Add clock definitions
This patch adds basic clock definition of am33xx SoC.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:36 +02:00
Chandan Nath
5655108a82 ARM:AM33XX: Added support for AM33xx
This patch adds basic support for AM33xx which is based on ARMV7
Cortex A8 CPU.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:36 +02:00