this eliminates compiler warnings when cmd_mmc.c is built with CONFIG_SYS_MMC_SET_DEV
the mmc_set_dev implementation in omap3_mmc.c is also tweaked to match
the new prototype in parameter naming and type
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP4 Panda is a reference board based on OMAP4430, an ARMV7 Cortex A9 CPU
This patch adds basic support for booting the board. It includes i2c and mmc
support. It assumes U-boot is loaded to SDRAM with the help of another small
bootloader (x-load) running from SRAM. U-boot currently relies on x-load for
clock, mux, and SDRAM initialization
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP4430 SDP is a reference board based on OMAP4430, an ARMV7 Cortex A9 CPU
This patch adds basic support for booting the board. It includes i2c and mmc
support. It assumes U-boot is loaded to SDRAM with the help of another small
bootloader (x-load) running from SRAM. U-boot currently relies on x-load for
clock, mux, and SDRAM initialization
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The purpose of this patch is to prepare for adding the OMAP4 architecture, which is Cortex A9
Cortex A8 and A9 both belong to the armv7 architecture, hence the name change.
The two architectures are similar enough that substantial code can be shared.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Now that we have a unified gpio layer, the different status led
implementations can be switched to the common gpio led driver.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When boards define CONFIG_BOARD_SPECIFIC_LED, the common led definitions
are OK for Blackfin boards. So switch the few boards using these over to
the common code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that we have a unified gpio layer, the misc partial gpio commands
can be unified and made complete (support all possible gpios).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands. Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".
This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:
int main (int argc, char **argv)
{
while (--argc > 0 && **++argv == '-') {
/* ====> */ while (*++*argv) {
switch (**argv) {
case 'd':
debug++;
break;
...
default:
usage ();
}
}
}
...
}
The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell. With the modification, the compiler will prevent this with
an
error: increment of read-only location '*argv'
N.B.: The code above can be trivially rewritten like this:
while (--argc > 0 && **++argv == '-') {
char *arg = *argv;
while (*++arg) {
switch (*arg) {
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Instead of defining the flags sevaral times in different source files
(which is error prone), move them to a central place in a header file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Change the return type of the *printf() functions to the standard
"int"; no changes are needed but returning the already available
length count.
This will save a few additional strlen() calls later...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Remove some INFERNO related #ifdef's from common environment code by
fixing the board configuration settings (add CONFIG_ENV_SECT_SIZE).
While we are at it, fix comment which incorrectly talks about 4 KB
environment size, while it's actually 0x4000 = 16 KiB.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Rolf Offermanns <rof@sysgo.de>
This patch enables booting with option E on the PPC460EX/EXr/GT.
When booting with Option E, the PLL is in bypass, CPR0_PLLC[ENG]=0.
The Software Boot Configuration Procedure is needed to engage the
PLL and perform a chip reset.
Signed-off-by: Stefan Roese <sr@denx.de>
On P2020RDB eTSEC2 is connected to Vitesse VSC8221 PHY via SGMII.
Current TBI PHY settings for SGMII mode cause link problems on
this platform, link never comes up.
Fix this by making TBI PHY settings configurable and add a working
configuration for P2020RDB.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Peter Tyser <ptyser@xes-inc.com>
Because the variable was getting defined twice.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
The AmigaOneG3SE board has been orphaned or a very long time, and
broken for more than 12 releases resp. more than 3 years. As nobody
seems to be interested any more in this stuff we may as well ged rid
of it, especially as it clutters many areas of the code so it is a
continuous pain for all kinds of ongoing work.
Signed-off-by: Wolfgang Denk <wd@denx.de>
CONFIG_SYS_BUS_HZ has not really been used anywhere except to be
redined as CONFIG_SYS_BUS_CLK; in addition, the mpc7448hpc2 had the
bogus CONFIG_SYS_CONFIG_BUS_CLK setting which duplicated the
funtionality. Change all this to use CONFIG_SYS_BUS_CLK consistently.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Frank Gottschling <fgottschling@eltec.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Eran Man <eran@nbase.co.il>
Cc: Stefan Roese <sr@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Currently EMAC_MDIO_PHY_NUM is defined as 1 in emac_defs.h.
Because of this, EMAC does not work on EVMs which do not have phy
connected at 1. Moving the macro to board config file makes this
configurable depending on where the phy is connected on the MDIO bus.
This patch fixes the board reset issue observed during network access
on DM365EVM. EMAC driver was assuming EMAC_MDIO_PHY_NUM as 1
but it is 0 on DM365EVM.
This patch is verified on da830/omap-l137, dm365 and dm644x evms.
Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Commit 37566090 "compiler.h: unify system ifdef cruft here" added both
a "#include <errno.h>" and a "extern int errno;" to include/compiler.h
which is causing build warnings for some systems, for example for the
"netstar" board:
In file included from /home/wd/git/u-boot/work/lib/crc32.c:15:
include/compiler.h:28: warning: function declaration isn't a prototype
The declaration of "errno" should be redundant, as <errno.h> is
supposed to provide a correct declaration, so drop it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Conflicts:
CONFLICT (rename/add): Rename
board/davinci/da830evm/Makefile->board/ti/tnetv107xevm/Makefile
in 89b765c7f6.
board/ti/tnetv107xevm/Makefile added in HEAD
But files were identical, so no problem.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds support for the LaCie ED Mini V2 product
which is based on the Marvell Orion5x SoC.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
This patch adds support for the Samsung Goni board (S5PC110 SoC)
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Provides initial support for TI OMAP-L138/DA850 SoC devices on
a Logic PD EVM board.
Provides:
Initial boot and configuration.
Support for i2c.
UART support (console).
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for the EMIF4 interface
available in the AM35x processors.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Consolidated SDRC related functions into one file - sdrc.c
And also replaced sdrc_init with generic memory init
function (mem_init), this generalization of omap memory setup
is necessary to support the new emif4 interface introduced in AM3517.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The EVMS have been shipping with NAND (instead of OneNAND) as default.
So, this patch sets NAND as default.
To choose OneNAND, define CMD_ONENAND instead of CMD_NAND in the
config file omap3_evm.h.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
TNETV107X is a Texas Instruments SoC based on an ARM1176 core, and with a
bunch on on-chip integrated peripherals. This patch adds support for the
TNETV107X EVM board.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The current ARM1176 CPU specific code is too specific to the SMDK6400
architecture. The following changes were necessary prerequisites for the
addition of other SoCs based on ARM1176.
Existing board's (SMDK6400) configuration has been modified to keep behavior
unchanged despite these changes.
1. Peripheral port remap configurability
The earlier code had hardcoded remap values specific to s3c64xx in start.S.
This change makes the peripheral port remap addresses and sizes configurable.
2. U-Boot code relocation support
Most architectures allow u-boot code to run initially at a different
address (possibly in NOR) and then get relocated to its final resting place
in RAM. Added support for this capability in ARM1176 architecture.
3. Disable TCM if necessary
If a ROM based bootloader happened to have initialized TCM, we disable it here
to keep things sane.
4. Remove unnecessary SoC specific includes
ARM1176 code does not really need this SoC specific include. The presence
of this include prevents builds on other ARM1176 archs.
5. Modified virt-to-phys conversion during MMU disable
The original MMU disable code masks out too many bits from the load address
when it tries to figure out the physical address of the jump target label.
Consequently, it ends up branching to the wrong address after disabling the
MMU.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for the EMIF4 interface
available in the AM35x processors.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Consolidated SDRC related functions into one file - sdrc.c
And also replaced sdrc_init with generic memory init
function (mem_init), this generalization of omap memory setup
is necessary to support the new emif4 interface introduced in AM3517.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The EVMS have been shipping with NAND (instead of OneNAND) as default.
So, this patch sets NAND as default.
To choose OneNAND, define CMD_ONENAND instead of CMD_NAND in the
config file omap3_evm.h.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
TNETV107X is a Texas Instruments SoC based on an ARM1176 core, and with a
bunch on on-chip integrated peripherals. This patch adds support for the
TNETV107X EVM board.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The current ARM1176 CPU specific code is too specific to the SMDK6400
architecture. The following changes were necessary prerequisites for the
addition of other SoCs based on ARM1176.
Existing board's (SMDK6400) configuration has been modified to keep behavior
unchanged despite these changes.
1. Peripheral port remap configurability
The earlier code had hardcoded remap values specific to s3c64xx in start.S.
This change makes the peripheral port remap addresses and sizes configurable.
2. U-Boot code relocation support
Most architectures allow u-boot code to run initially at a different
address (possibly in NOR) and then get relocated to its final resting place
in RAM. Added support for this capability in ARM1176 architecture.
3. Disable TCM if necessary
If a ROM based bootloader happened to have initialized TCM, we disable it here
to keep things sane.
4. Remove unnecessary SoC specific includes
ARM1176 code does not really need this SoC specific include. The presence
of this include prevents builds on other ARM1176 archs.
5. Modified virt-to-phys conversion during MMU disable
The original MMU disable code masks out too many bits from the load address
when it tries to figure out the physical address of the jump target label.
Consequently, it ends up branching to the wrong address after disabling the
MMU.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add the new board PM9G45 from Ronetix GmbH.
* AT91SAM9G45 MCU at 400Mhz.
* 128MB DDR2 SDRAM
* 256MB NAND
* 10/100 MBits Ethernet DP83848
* Serial number chip DS2401
The board is made as SODIMM200 module.
For more info www.ronatix.at or info@ronetix.at.
Signed-off-by: Asen Dimov <dimov@ronetix.at>
This patch changed the SICRL_USBDR define to reflect the 4 different bit
settings for this two-bit field. The four different options are '00', '01',
'10', and '11'. This patch also corrects the config file for SIMPC8313 and
MPC8313ERDB for the appropriate fields. This change only affects the MPC8313
cpu.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds gpio support of Altera PIO component to the
nios2-generic board. Though it drives only gpio_led at the
moment, it supports bidirectional port to control bit-banging
I2C, NAND flash busy status or button switches, etc.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Tested-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
create_pipe() can give wrong result if an expression is passed as the 'endpoint'
argument -- due to missing parentheses.
Thanks to Martin Mueller for finding the bug and providing the patch.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
"down_write_trylock" needs to return 1 instead of 0 for success.
Otherwise copying a block with a read error (e.g. bit-flip on read)
won't work correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch sets the SICRL_LBC bits in SICRL to change the function of the
associated pins to GPIO functionality.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Add USB commands.
Rename autoscript to bootscript.
Add automatic bootscript image generation to makefile.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Added UPM array table, upmconfig, and Local Bus configuration support for SIMPC8313
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Only one file apparently defines this function, and it merely stubs
it out. So if no one is defining/calling it, punt it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
With the cpu include paths moved, the gitignore paths need updating.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Tom Rix <tom@bumblecow.com>
Recent crc changes started using the "uint" type in headers that are used
on the build system. This subsequently broke mingw targets as they do not
provide such a type. So add this basic typedef to compiler.h so that we
do not have to worry about this breaking again in the future.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add ECC support for DDR RAM for MV64360 on esd CPCI-CPU/750 board.
This patch also adds the "pldver" command to display the CPLD
revision.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for newer (up to 2.6.33) kernels
Add zboot command which takes the address of a bzImage as its first
argument and (optionally) the size of the bzImage as the second argument
(the second argument is needed for older kernels which do not include
the bzImage size in the header)
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Modify print_size() so that it can accept numbers larger than 4GB on 32-bit
systems.
Add support for display terabyte, petabyte, and exabyte sizes. Change the
output to use International Electrotechnical Commission binary prefix standard.
Signed-off-by: Timur Tabi <timur@freescale.com>
The MC13892 is a Power Controller used with processors
of the family MX.51. The file adds definitions to be used to setup
the internal registers via SPI.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The RTC is part of the Freescale's PMIC controller.
Use general function to access to PMIC internal registers.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
The patch add supports for the Freescale's Power
Management Controller (known as Atlas) used together with i.MX31/51
processors. It was tested with a MC13783 (MX31) and
MC13892 (MX51).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Add a new function to the eth_device struct for programming a network
controller's hardware address.
After all network devices have been initialized and the proper MAC address
for each has been determined, make a device driver call to program the
address into the device. Only device instances with valid unicast addresses
will be programmed.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Tested-by: Prafulla Wadaskar <prafulla@marvell.com>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
This driver supports the Altera triple speeds 10/100/1000 ethernet
mac.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch ports the opencore 10/100 ethernet mac driver ethoc.c
from linux kernel to u-boot.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The NAND device is connected to the FPGA of the QONG board
and not to the NFC controller. For this reason, the FPGA must
be set and initialized before accessing to the NAND itself.
Signed-off-by: Stefano Babic <sbabic@denx.de>
moved CONFIG_CMD_FAT to filesystem section
swapped CONFIG_CMD_NAND and CONFIG_CMD_MII so they are alpha correct
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
This patch includes a few additional commands in the sheevaplug
version of u-boot:
- support for LONGHELP so you can get help messages
- auto completion and command editing
- ubi and mii support
- ext2 filesystem (convenient if you have an ext2 from which you want to boot)
- jffs2 and ubifs filesystems (if you want to use these in NAND)
This also makes it more similar to openrd client.
Side effect of this patch is that the code now needs 3 sectors i.s.o. 2
so an existing env is overwritten
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
The lowlevel_init file contained some hard-coded values
to setup the RAM. These board related values are moved into
the board configuration file.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This patch adds support for the magnesium board from
projectiondesign. This board uses i.MX27 SoC and has
8MB NOR flash, 128MB NAND flash, FEC ethernet controller
integrated into i.MX27. As this port is based on
the imx27lite port, common config options are collected
in include/configs/imx27lite-common.h
Signed-off-by: Heiko Schocher <hs@denx.de>
Because of other s5p series SoC will use these serial functions,
modify function's name and structure's name.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch fixes APC405 build, by defining CONFIG_PPC4XX_I2C. This is
needed since the move of the PPC4xx I2C driver into the drivers/i2c
directory.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
This patch adds support for the Mosaix Technologies, Inc. ICON board,
based on the AppliedMicro (AMCC) PPC440SPe. It's equipped with an SODIMM
(512MB standard) and 64MByte of NOR FLASH.
Support for the onboard SM502 will be added later.
Signed-off-by: Stefan Roese <sr@denx.de>
This is a generic approach to port u-boot for nios2 boards.
You may find the usage of this approach on the nioswiki,
http://nioswiki.com/DasUBoot
A fpga parameter file, which contains base address information
and drivers declaration, is generated from Altera's hardware system
description sopc file using tools.
The example fpga parameter file is compatible with EP1C20, EP1S10
and EP1S40 boards. So these boards can be removed after this commit.
Though epcs controller is removed to cut the dependency of altera_spi
driver.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
PDM360NG is a MPC5121E based board by ifm ecomatic gmbh.
Signed-off-by: Michael Weiss <michael.weiss@ifm.com>
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Configure CONFIG_SYS_MAX_RAM_SIZE address range in
DDR Local Access Window and determine the RAM size.
Fix DDR LAW afterwards using detected RAM size.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Extend mpc512x serial driver to support multiple PSC ports.
Subsequent patches for PDM360NG board support make use of this
functionality by defining CONFIG_SERIAL_MULTI in the board config
file. Additionally the used PSC devices are specified by defining
e.g. CONFIG_SYS_PSC1, CONFIG_SYS_PSC4 and CONFIG_SYS_PSC6.
Support for PSC devices other than 1, 3, 4 and 6 is not added
by this patch because these aren't used currently. In the future
it can be easily added using DECLARE_PSC_SERIAL_FUNCTIONS(N) and
INIT_PSC_SERIAL_STRUCTURE(N) macros in cpu/mpc512x/serial.c.
Additionally you have to add code for registering added
devices in serial_initialize() in common/serial.c.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Subsequent patch extends mpc512x serial driver to support
multiple PSC ports. The driver will provide an uninit()
function to stop the serial controller and to disable the
controller's clock. Adding uninit() entry to struct serial_device
allows disabling the serial controller after usage of
a stdio serial device.
This patch adds uninit() entry to the struct serial_device
and fixes initialization of this structure in the code
accordingly.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
On some Freescale SoC Internal DMA of eSDHC controller has bug.
So PIO Mode has been introduced to do data transfer using CPU.
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
before, MPC8349ITX boots u-boot in 4.3sec:
column1 is elapsed time since first message
column2 is elapsed time since previous message
column3 is the message
0.000 0.000: U-Boot 2010.03-00126-gfd4e49c (Apr 11 2010 - 17:25:29) MPC83XX
0.000 0.000:
0.000 0.000: Reset Status:
0.000 0.000:
0.032 0.032: CPU: e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz
0.032 0.000: Board: Freescale MPC8349E-mITX
0.032 0.000: UPMA: Configured for compact flash
0.032 0.000: I2C: ready
0.061 0.028: DRAM: 256 MB (DDR1, 64-bit, ECC off, 266.667 MHz)
1.516 1.456: FLASH: 16 MB
2.641 1.125: PCI: Bus Dev VenId DevId Class Int
2.652 0.011: 00 10 1095 3114 0180 00
2.652 0.000: PCI: Bus Dev VenId DevId Class Int
2.652 0.000: In: serial
2.652 0.000: Out: serial
2.652 0.000: Err: serial
2.682 0.030: Board revision: 1.0 (PCF8475A)
3.080 0.398: Net: TSEC1: No support for PHY id ffffffff; assuming generic
3.080 0.000: TSEC0, TSEC1
4.300 1.219: IDE: Bus 0: .** Timeout **
after, MPC8349ITX boots u-boot in 3.0sec:
0.010 0.010: U-Boot 2010.03-00127-g4b468cc-dirty (Apr 11 2010 - 17:47:29) MPC83XX
0.010 0.000:
0.010 0.000: Reset Status:
0.010 0.000:
0.017 0.007: CPU: e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz
0.017 0.000: Board: Freescale MPC8349E-mITX
0.038 0.020: UPMA: Configured for compact flash
0.038 0.000: I2C: ready
0.038 0.000: DRAM: 256 MB (DDR1, 64-bit, ECC off, 266.667 MHz)
0.260 0.222: FLASH: 16 MB
1.390 1.130: PCI: Bus Dev VenId DevId Class Int
1.390 0.000: 00 10 1095 3114 0180 00
1.390 0.000: PCI: Bus Dev VenId DevId Class Int
1.400 0.010: In: serial
1.400 0.000: Out: serial
1.400 0.000: Err: serial
1.400 0.000: Board revision: 1.0 (PCF8475A)
1.832 0.432: Net: TSEC1: No support for PHY id ffffffff; assuming generic
1.832 0.000: TSEC0, TSEC1
3.038 1.205: IDE: Bus 0: .** Timeout **
also tested on these boards (albeit with a less accurate
boottime measurement method):
seconds: before after
8349MDS ~2.6 ~2.2
8360MDS ~2.8 ~2.6
8313RDB ~2.5 ~2.3 #nand boot
837xRDB ~3.1 ~2.3
also tested on an 8323ERDB.
v2: also remove the delayed icache enablement assumption in arch ppc's
board.c, and add a CONFIG_MPC83xx define in the ITX config file for
consistency (even though it was already being defined in 83xx'
config.mk).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.
Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
This patch adds a callpoint in i2c_init that allows board specific
i2c board initialization (typically for i2c bus reset) that is called
after i2c_init operations, allowing the i2c_board_late_init function
to use the pre-configured i2c bus speed and slave address.
The 440SPe Rev. A is quite old and newer 440SPe boards don't need support
for this CPU revision. Since removing support for this older version
simplifies the creation for newer U-Boot ports, this patch now enables
440SPe > Rev. A support by creating the CONFIG_440SPE_REVA define. By
defining this in the board config header, Rev. A will still be supported.
Otherwise (default for newer board ports), Rev. A will not be supported.
Signed-off-by: Stefan Roese <sr@denx.de>
The latest changes increased the size of the alpr image a bit more.
Now it doesn't fit into the 256k reserved for it. This patch now removes
the commands "loads" and "loadb" which are not needed in the production
systems.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pieter Voorthuijsen <pieter.voorthuijsen@prodrive.nl>
This helps to clean up the include/ directory so that it only contains
non-architecture-specific headers and also matches Linux's directory
layout which many U-Boot developers are already familiar with.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The appropriate include/asm-$ARCH directory should already by symlinked
to include/asm so using the whole "asm-$ARCH" path is unnecessary.
This change should also allow us to move the include/asm-$ARCH
directories into their appropriate lib/$ARCH/ directories.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Now that the other architecture-specific lib directories have been
moved out of the top-level directory there's not much reason to have the
'_generic' suffix on the common lib directory.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Also move lib_$ARCH/config.mk to arch/$ARCH/config.mk
This change is intended to clean up the top-level directory structure
and more closely mimic Linux's directory organization.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The MPC8536DS_NAND SPL build was failing due to code size increase
introduced by commit:
commit 33f57bd553
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Fri Mar 26 15:14:43 2010 -0500
85xx: Fix enabling of L1 cache parity on secondary cores
We built in some NS16550 functions that we dont need and can get
rid of them via CONFIG_NS16550_MIN_FUNCTIONS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale P2020DS board uses a new type of PIXIS FPGA, called the ngPIXIS.
The ngPIXIS has one distinct new feature: the values of the on-board switches
can be selectively overridden with shadow registers. This feature is used to
boot from a different NOR flash bank, instead of having a register dedicated
for this purpose. Because the ngPIXIS is so different from the previous PIXIS,
a new file is introduced: ngpixis.c.
Also update the P2020DS checkboard() function to use the new macros defined
in the header file.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Refactor and document the Freescale PIXIS code, used on most 85xx and 86xx
boards. This makes the code easier to read and more flexible.
Delete pixis.h, because none of the exported functions were actually being
used by any other file. Make all of the functions in pixis.c 'static'.
Remove "#include pixis.h" from every file that has it.
Remove some unnecessary #includes.
Make 'pixis_base' into a macro, so that we don't need to define it in every
function.
Add "while(1);" loops at the end of functions that reset the board, so that
execution doesn't continue while the reset is in progress.
Replace in_8/out_8 calls with clrbits_8, setbits_8, or clrsetbits_8, where
appropriate.
Replace ulong/uint with their spelled-out equivalents. Remove unnecessary
typecasts, changing the types of some variables if necessary.
Add CONFIG_SYS_PIXIS_VCFGEN0_ENABLE and CONFIG_SYS_PIXIS_VBOOT_ENABLE to make
it easier for specific boards to support variations in the PIXIS registers
sets. No current boards appears to need this feature.
Fix the definition of CONFIG_SYS_PIXIS_VBOOT_MASK for the MPC8610 HPCD.
Apparently, "pixis_reset altbank" has never worked on this board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The HID1[MBDD] bit is new on rev5.0 or greater cores and will optimize
the performance of mbar/eieio instructions.
Signed-off-by: Sandeep Gopalpet <sandeep.kumar@freescale.com>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added P1012/P1013/P1021/P1022 to cpu_type_list and SVR list
* Added number of LAWs for P1012/P1013/P1021/P1022
* Set CONFIG_MAX_CPUS to 2 for P1021/P1022
* PCI port config
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Switch to the SMC911X driver by default now, and fix LDR env settings.
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add a helper function that given an alias will delete both the node
the alias points to and the alias itself
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
When we set the read or write watermark in WML we should maintain the
rest of the register as is, rather than using some hard coded value.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To support multiple block read command we must set abort or use auto
CMD12. If we booted from eSDHC controller neither of these are used
and thus we need to reset the controller to allow multiple block read
to function.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We need to stop the clocks on 83xx/85xx as well as imx. No need to make
this code conditional to just imx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Stefano Babic <sbabic@denx.de>
This patch moves the PPC4xx specific I2C device driver into the I2C
drivers directory. All 4xx config headers are updated to include this
driver.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch is part of migrating the AT91 support towards
using C struct for all SOC access.
It removes one more CONFIG_AT91_LEGACY warning.
at91_pmc.h needs cleanup after migration of the drivers
has been done.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
CONFIG_CMD_AUTOSCRIPT support is deprecated and non-existing
This clean up patch removes the references for esd boards
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Add setup for ethernet on SMDKC100, allowing kernel/ramdisk to be
loaded over tftp.
The preinit function will configure GPIO (GPK0CON) & SROMC to look
for environment in SROM Bank 3.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Nand Flash, Ethernet, other features might need to configure the
SROMC registers accordingly.
The config_sromc() functions helps with this.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Memory subsystem of S5PC100 handles SROM, SRAM, OneDRAM, OneNand,
NAND Flash, DDRs.
smc.h is a common place for the register description of Memory subsystem
of S5PC100.
Note: Only SROM related registers are descibed now.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The get_pll_clk(int) API returns the PLL frequency based on
the (int) argument which is defined locally in clock.c
Moving that #define to common header file (clk.h) would
be helpful when using the API from other files.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
CONFIG_SYS_HZ was being calculated (incorrectly) in nios2 configuration
headers. Updated comments to accurately describe timebase macros.
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
The outx/writex macros were using writex(addr, val) rather than
the standard writex(val, addr), resulting in incompatibilty with
architecture independent components. This change set uses standard
parameter order.
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Copy from linux header. This is needed for generic bitops.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
The standard Altera UART & JTAG UART as well as the OpenCores
YANU driver are now in individual files in drivers/serial
rather than a single file uner cpu/nios2.
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
After determining how much DDR is actually in the system, set DBAT0 and
IBAT0 accordingly. This ensures that the CPU won't attempt to access
(via speculation) addresses outside of actual memory.
On 86xx systems, DBAT0 and IBAT0 (the BATs for DDR) are initialized to 2GB
and kept that way. If the system has less than 2GB of memory (typical for
an MPC8610 HPCD), the CPU may attempt to access this memory during
speculation. The zlib code is notorious for generating such memory reads,
and indeed on the MPC8610, uncompressing the Linux kernel causes a machine
check (without this patch).
Currently we are limited to power of two sized DDR since we only use a
single bat. If a non-power of two size is used that is less than
CONFIG_MAX_MEM_MAPPED u-boot will crash.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the same code between primary and secondary cores to init the
L1 cache. We were not enabling cache parity on the secondary cores.
Also, reworked the L1 cache init code to match the e500mc L2 init code
that first invalidates the cache and locks. Than enables the cache and
makes sure its enabled before continuing.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ml300 board has a number of issues, but nobody cares about this
long-orphaned board any more. Remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu>
The CF will call cache functions in lib_m68/cache.c and the
cache settings are defined in platform configuration file.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Reside Ethernet buffer descriptors in SRAM instead of DRAM. Add
CONFIG_SYS_TX_ETH_BUFFER in platform configuration file. Update
DRAM control and SRAM control register setting. Update cache
setting where size does not write to proper region.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Fix incorrect default environment for flash erase or protect
range. Change offset from 0 to 0xff80nnnn. Remove default
ethernet setup and MAC address.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Provide parameter passing to uart_port_config(). Update port
configuration - un-mask it before enable the bits.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Use correct definition for _MASK and _UNMASK. It was combined in
the previous used and causes confusion.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Using seperate function calls for each bit-bang of slave serial
load can be painfully slow. This patch adds the possibility to
supply a block write function that loads the complete block of
data in one call (like it can already be done with Altera FPGAs).
On an MCF5373L (240 MHz) loading an XC3S4000 this reduces the load
time from around 15 seconds to around 3 seconds
Signed-off-by: Wolfgang Wegner <w.wegner at astro-kom.de>
440EPx fixed bootstrap options A, B, D, and E sets PLL FWDVA to a value = 1.
This results in the PLLOUTB being greater than the CPU clock frequency
resulting unstable 440EPx operation resulting in various software hang
conditions.
This patch reprograms the FWDVA satisfying the requirement of setting FWDVB
to a value greater than 1 while using one of the four deafult bootstrap options.
Signed-off-by: Rupjyoti Sarmah <rsarmah@amcc.com>
Acked-by : Victor Gallardo <vgallardo@appliedmicro.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The soft-i2c code for AT91 defines I2C_SOFT_DECLARATIONS
for direct access by dereferencing a pio pointer.
The OTC570 platform uses the AT91 gpio API so it does not
need the pio variable.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Allow overwriting defined partitions in the device tree blob
using partition info defined in the 'mtdparts' environment
variable.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Gerald Van Baren <vanbaren@cideas.com>
Add POST progress API implemented as weak calls before and after
each call to the POST test callback in the post_run_single routine
of the post.c file.
Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
Acked-by: Detlev Zundel <dzu@denx.de>
I executed 'find . -name "*.[chS]" -perm 755 -exec chmod 644 {} \;'
Signed-off-by: Thomas Weber <swirl@gmx.li>
Add some more: neither Makefile nor config.mk need execute permissions.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The new zlib code wants asm/unaligned.h, so have the Blackfin version pull
in the asm-generic/unaligned.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This is based on the asm-arm/unaligned.h, but made generic so all arches
that cannot do unaligned accesses can utilize it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This code has compile problems and the company does not even exist any
more. So we take the liberty to drop support for it.
Signed-off-by: Detlev Zundel <dzu@denx.de>
CC: Wolfgang Denk <wd@denx.de>
CC: Ben Warren <biggerbadderben@gmail.com>
The 36-bit build exceeds the 512k size we have. Removing FIT type image
support allows us to fit and we dont really use it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also enable support for CONFIG_HWCONFIG because we use this for
configuring if this hardware has a FEC or not.
syntax:
hwconfig=fec:on if hardware has an fec
hwconfig=fec:off if hardware has no fec
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch uses gd->relocaddr variable to store uboot's relocated
address in RAM and shows it in bdinfo command.
This patch moves CONFIG_AMIGAONEG3SE style copying of the address
in board_init_f to just before relocation is actually done.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Tested-by: Detlev Zundel <dzu@denx.de>
* convert otc570 board to use c stucture SoC access
* change gpio access to at91_gpio syntax
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
The patch removes warnings at compile time and provides
some cleanup code:
- Removed comment on NAND (not yet supported) from lowlevel_init.S
- Removed NFMS bit definition from imx-regs.h
The bit is only related to MX.25/35 and can lead to confusion
- Moved is_soc_rev() to soc specific code (removed from mx51evk.c)
Signed-off-by: Stefano Babic <sbabic@denx.de>
Add support for the ARM part of the mgcoge2, named suen3.
This board is based on the Marvell Kirkwood (88F6281) SoC.
As there come more board variants, common config options
are collected in include/configs/km_arm.h. Also, this board
use common code for all keymile boards, which is stored in
board/keymile/common/common.c
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Heiko Schocher <hs@denx.de>
This is an i.MX25 base board with only NAND
so it uses nand_spl to boot.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Tune configuration, add support for (redundant) environment in NAND.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
CC: Fred Fan <fanyefeng@gmail.com>
CC: Tom <Tom.Rix@windriver.com>
general cleanup
move clock init to cpu_eth_init in cpu/arm926ejs/mx27/generic.c
make MX27 specific phy init conditional on CONFIG_MX27
replace call to imx_get_ahbclk with one to imx_get_fecclk
and define imx_get_fecclk in include/asm-arm/arch-mx27/clock.h
Signed-off-by: John Rigby <jcrigby@gmail.com>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Fred Fan <fanyefeng@gmail.com>
CC: Tom <Tom.Rix@windriver.com>
ARM926EJS core with MX31 peripherals.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Earlier Version Signed-off-by: Wolfgang Denk <wd@denx.de>
CC: Fred Fan <fanyefeng@gmail.com>
CC: Tom <Tom.Rix@windriver.com>
remove ifdef'd clock selection code from
serial_mxc.c and replace with call to imx_get_uartclk
Add definitions for imx_get_uartclk to imx31 and imx27
include files.
This makes it easier to add new imx platforms.
Signed-off-by: John Rigby <jcrigby@gmail.com>
The patch adds initial support for the Freescale mx51evk board.
Network (FEC) and SD controller (fsl_esdhc) are supported.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fred Fan <fanyefeng@gmail.com>
The esdhc controller in the mx51 processor is quite
the same as the one in some powerpc processors
(MPC83xx, MPC85xx). This patches adapts the driver
to support the arm mx51.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Some Freescale's processors of different architecture
have the same peripheral (eSDHC controller in PowerPC
and i.MX51). This patch adds accessors for
the internal registers of the SOCs, as already
implemented in the PowerPC architecture.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Most controllers can check if there is a card in the slot.
However, they require pins that could be not available because
required by other functions and the detection of a card must
be performed in another way. This patch adds a weak function
that a board can implement to add its internal custom way
to check the presence of a MMC/SD card.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The patch add header files to support the pin multiplexer
of the the Freescale i.MX51 processor.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fred Fan <fanyefeng@gmail.com>
The patch add header files to support the Freescale i.MX51
processor, setting definitions for internal registers.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fred Fan <fanyefeng@gmail.com>
The patch add initial support for the Freescale i.MX51 processor
(family arm cortex_a8).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fred Fan <fanyefeng@gmail.com>
Configuration defines should be preceeded with CONFIG_SYS_. Renamed
some at91 specific defines to conform to this naming convention:
AT91_CPU_NAME to CONFIG_SYS_AT91_CPU_NAME
AT91_MAIN_CLOCK to CONFIG_SYS_AT91_MAIN_CLOCK
Signed-off-by: Achim Ehrlich <aehrlich@taskit.de>
Reindent configuration header to limit line lenght to 80 characters by
removing obvious and sometimes misleading comments.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Limit line length to 80 characters mostly by removing obvious and sometimes
misleading comments. Fix indentation, too.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Adds support for ethernet networking on the da830evm platform.
This platform uses an SoC EMAC interface and a 3 port ethernet
switch as a PHY with an RMII interface. The PHY also has a i2c
interface for configuring the switch functions.
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Recent kernels are using generic NAND and NOR drivers. Change
default mtdparts to reflect it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Correct switching partitions after upgrade and make it more readable.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
lib_generic/zlib.c needs include/asm/unaligned.h since commit
cd514aeb99, which broke compilation for
Coldfire/M68K. This patch adds the missing header for these
architectures.
Signed-off-by: Wolfgang Wegner <w.wegner at astro-kom.de>
zlib.c demands asm/unaligned.h. But, SH does not have these.
This commit add asm/unaligned.h and asm/unaligned-sh4a.h from Linux
kernel and modifyf for u-boot.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Corrected the bit field positions of the external master priority low
and the external master priority high values in the EBC configuration
register. These bit field positions differ between PPC405 and PPC440
processors
Signed-off-by: Eugene O'Brien <eugene.obrien@advantechamt.com>
Signed-off-by: Stefan Roese <sr@denx.de>
and avoid e.g., two identical boards from causing random networking
conflicts when hooked up to the same network.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* new board (eb_cpux9k2)
* support for EB+CPUx9K2 board by BuS Elektronik GmbH & Co. KG
* select via make eb_cpux9k2_config
* this also demonstrates, how to use boards with AT91RM9200 cpu
in at91 arch tree
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* add's at91_emac (AT91RM9200) network driver (NET_MULTI api)
* enable driver with CONFIG_DRIVER_AT91EMAC
* generic PHY initialization
* modify AT91RM9200 boards to use NET_MULTI driver
* the drivers has been tested with LXT971 Phy and DM9161 Phy at MII and RMII
interface
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* prepare joining at91 and at91rm9200
* add modified copy of soc files to cpu/arm920t/at91 to make
possible to compile at91rm9200 boards in at91 tree instead
of at91rm9200
* add header files with c structure defs for AT91 MC, ST and TC
* the new cpu files are using at91 c structure soc access
* please read README.soc-at91 for details
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* add's a warning to all files, which need update to new SoC access
* convert common files in cpu/../at91 and a lot of drivers to use
c stucture SoC access
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* add a real AT91 GPIO driver instead of header inline code
* resolve the mixing of port and pins
* change board config files to use new driver
* add macros to gpio to realize backward compatibility
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* add's the new temporary CONFIG_AT91_LEGACY to all board configs
This will need for backward compatiblity, while change the SoC access
to c structures. If CONFIG_AT91_LEGACY is defined, the deprecated
SoC is used.
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
The EVM UI extender card has a NAND device. This change will enable
saveenv to work with NAND and Linux to be booted using:
mtdparts default
nboot kernel
bootm
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The structure was missing a reserved entry (not listed in the manual,
actually), so the last registers had a wrong offset. This prevented
all swlocked registers to be modified as swlock is last in the structure.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Added support for the following EDB93xx boards:
EDB9301
EDB9302
EDB9302A
EDB9307
EDB9307A
EDB93012
EDB9315
EDB9315A
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
This patch removes "CONFIG_CMD_JFFS" from the board config
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Every omap3 board config file declared the global variable gpmc_cfg.
This changes moves the declaration to a better location in the
arch dependent header file cpu.h.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
