At present CONFIG_CMD_HASH enables the 'hash' command which also brings
in the hashing API. Some boards may wish to enable the API without the
command. Add a separate CONFIG to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit 94e3c8c4fd ("crypto/fsl - Add progressive hashing support
using hardware acceleration.") created entries for CONFIG_SHA1,
CONFIG_SHA256, CONFIG_SHA_HW_ACCEL, and CONFIG_SHA_PROG_HW_ACCEL.
However, no defconfig has migrated to it. Complete the move by first
adding additional logic to various Kconfig files to select this when
required and then use the moveconfig tool. In many cases we can select
these because they are required to implement other drivers. We also
correct how we include the various hashing algorithms in SPL.
This commit was generated as follows (after Kconfig additions):
[1] tools/moveconfig.py -y SHA1 SHA256 SHA_HW_ACCEL
[2] tools/moveconfig.py -y SHA_PROG_HW_ACCEL
Note:
We cannot move SHA_HW_ACCEL and SHA_PROG_HW_ACCEL simultaneously
because there is dependency between them.
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BOARD_INIT
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
So far we were not using the FIT image format to its full potential:
The SPL FIT loader was just loading the first image from the /images
node plus one of the listed DTBs.
Now with the refactored loader code it's easy to load an arbitrary
number of images in addition to the two mentioned above.
As described in the FIT image source file format description, iterate
over all images listed at the "loadables" property in the configuration
node and load every image at its desired location.
This allows to load any kind of images:
- firmware images to execute before U-Boot proper (for instance
ARM Trusted Firmware (ATF))
- firmware images for management processors (SCP, arisc, ...)
- firmware images for devices like WiFi controllers
- bit files for FPGAs
- additional configuration data
- kernels and/or ramdisks
The actual usage of this feature would be platform and/or board specific.
Also update the FIT documentation to mention the new SPL feature and
provide an example .its file to demonstrate its features.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lokesh Vutla <lokeshvuta@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
At the moment we load two images from a FIT image: the actual U-Boot
image and the .dtb file. Both times we have very similar code, that deals
with alignment requirements the media we load from imposes upon us.
Factor out this code into a new function, which we just call twice.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Jagan Teki <jagan@openedev.com>
At the moment we ignore any errors due to missing FIT properties,
instead go ahead and calculate our addresses with the -1 return value.
Fix this and bail out if any of the mandatory properties are missing.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Currently the SPL FIT loader always looks only for the first image in
the /images node a FIT tree, which it loads and later executes.
Generalize this by looking for a "firmware" property in the matched
configuration subnode, or, if that does not exist, for the first string
in the "loadables" property. Then using the string in that property,
load the image of that name from the /images node.
This still loads only one image at the moment, but refactors the code to
allow extending this in a following patch.
To simplify later re-usage, we also generalize the spl_fit_select_index()
function to not return the image location, but just the node offset.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lokesh Vutla <lokeshvuta@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Currently the SPL FIT loader uses the spl_fit_select_fdt() function to
find the offset to the right DTB within the FIT image.
For this it iterates over all subnodes of the /configuration node in
the FIT tree and compares all "description" strings therein using a
board specific matching function.
If that finds a match, it uses the string in the "fdt" property of that
subnode to locate the matching subnode in the /images node, which points
to the DTB data.
Now this works very well, but is quite specific to cover this particular
use case. To open up the door for a more generic usage, let's split this
function into:
1) a function that just returns the node offset for the matching
configuration node (spl_fit_find_config_node())
2) a function that returns the image data any given property in a given
configuration node points to, additionally using a given index into
a possbile list of strings (spl_fit_select_index())
This allows us to replace the specific function above by asking for the
image the _first string of the "fdt" property_ in the matching
configuration subnode points to.
This patch introduces no functional changes, it just refactors the code
to allow reusing it later.
(diff is overly clever here and produces a hard-to-read patch, so I
recommend to throw a look at the result instead).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lokesh Vutla <lokeshvuta@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Jagan Teki <jagan@openedev.com>
- Add #undef CONFIG_DM_MMC_OPS to omap3_logic in the SPL build case, to
match other TI platforms in the same situation.
Signed-off-by: Tom Rini <trini@konsulko.com>
Due to a typo, the 24 bit-per-pixel configuration ends in 24BMP
instead of 24BPP. This change renames it throughout the source tree
for consistency and to make moving these options into Kconfig easier
and less error-prone.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Some DVI monitors don't show anything in HDMI mode since audio stream
confuses them. To solve this situation, this commit adds HDMI flag in
timing data and sets it accordingly during edid parsing.
First existence of extension block is checked. If it exists and it is
CEA861 extension, then data blocks are checked for presence of HDMI
vendor specific data block. If it is present, HDMI flag is set.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Timing flags are never set, so they may contain garbage. Since some
drivers check them, video output may be broken on those drivers.
Initialize them to 0 and check for few common flags.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Coldfire arch is not happy with timer_init since interrupt handlers
are still not set at that stage, and the boot hangs silently.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
ATF(ARM Trusted Firmware) is used by ARM arch64 SoCs, find more infomation
about ATF at: https://github.com/ARM-software/arm-trusted-firmware
SPL is considered as BL2 in ATF terminology, it needs to load other parts
of ATF binary like BL31, BL32, SCP-BL30, and BL33(U-Boot). And needs to
prepare the parameter for BL31 which including entry and image information
for all other images. Then the SPL handle PC to BL31 with the parameter,
the BL31 will do the rest of work and at last get into U-Boot(BL33).
This patch needs work with patches from Andre for SPL support multi
binary in FIT.
The entry point of bl31 and bl33 are still using hard code because we
still can not get them from the FIT image information.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This simplifies makefiles. Also, arrange the order of objects in
drivers/mmc/Makefile so that the framework objects are listed before
drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now CONFIG_GENERIC_MMC and CONFIG_MMC match for all defconfig.
We do not need two options for the same feature. Deprecate the
former.
This commit was generated with the sed script 's/GENERIC_MMC/MMC/'
and manual fixup of drivers/mmc/Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With gcc-6 and later we may get a warning such as:
.../common/cli_readline.c:20:21: warning: ‘tab_seq’ defined but not used [-Wunused-const-variable=]
static const char tab_seq[] = " "; /* used to expand TABs */
^~~~~~~
.../common/cli_readline.c:19:19: warning: ‘erase_seq’ defined but not used [-Wunused-const-variable=]
static const char erase_seq[] = "\b \b"; /* erase sequence */
^~~~~~~~~
Because in SPL we're normally not doing interactive commands anyhow, so
lets just not compile this at all in SPL. This also means that we need
to correct the logic (and comment) about what the drivers/ddr/fsl/ and
CONFIG_FSL_DDR_INTERACTIVE requires and this will be included in SPL
there.
Signed-off-by: Tom Rini <trini@konsulko.com>
env_attr_lookup call env_attr_walk with
callback = regex_callback.
In env_attr_walk
attributes = strchr(entry_cpy, ENV_ATTR_SEP)
will return NULL if ENV_ATTR_SEP is not found.
In the aftermath regex_callback may call
strlen(attributes)
with a NULL value which will lead to a failure.
The problem was indicated by scan-clam.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The SPL-DFU feature enable to load and
execute u-boot from RAM over usb from
PC using dfu-util.
Hence dfu-reset should not be issued
when dfu-util -R switch is issued.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Since SPL_DFU_SUPPORT is depends on SPL_RAM_SUPPORT,
hence select SPL_DFU_SUPPORT only when
SPL_RAM_SUPPORT is chosen.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In single stage bootmode or falcon boot mode, the SPL shall update the
device tree that we load with the normal fixups done via
arch_fixup_fdt(), when possible (ie we have enough information in this
restricted environment to be able to do that still). This will include
for example updating them memory nodes.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
[trini: Reword commit message]
Adding support for fdt fixup to update the
memory node in device tree for falcon boot.
This is needed for single stage or falcon
bootmode, to pass memory configuration to
kernel through DT memory node.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Move the assignment of board info to global data a bit early which is
safe,
so that ram details can be used to enable caches.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
For the RK3399-Q7, we need some flexibility (depending on the feature
set we include in the SPL stage and how large our SPI flash is) in
positioning the SPL payload (i.e. the FIT image containing U-Boot, ATF
and the M0 payload) in our SPI flash.
To avoid having to deal with this through different U-Boot images, we
introduce a the '/config/u-boot,spl-payload-offset' property node
allow it to override the default setting.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Similar to what blk_get_device_part_str() does, this patch makes
part_get_info_by_name() return the partition number in case of a match.
This is useful when the partition number is needed and not just the
descriptor.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the Android image header format to the latest version published
in AOSP. The original code moved to a new repository, so this patch also
updates the reference to that path.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adjust this function so that we can convert it to support CONFIG_DM_VIDEO
without a lot of code duplication.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
The DM version of scsi_scan() is becoming a bit long, it can be split:
scsi_scan() iterates over the IDs and LUNs and for each id/lun pair calls
do_scsi_scan_one() to do the work of:
- detecting an attached drive
- creating the associated block device if a drive is found.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present fdt blob or argument address being passed to kernel is fixed at
compile time using macro CONFIG_SYS_SPL_ARGS_ADDR. FDT blob from
different media like nand, nor flash are copied to the address pointed
by the macro.
The problem is, it makes args/fdt blob compulsory to copy which is not required
in cases like for NOR Flash. This patch removes this limitation.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
simpler to read
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
this makes it easier comparable to the double-buffered version
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
setup_flash_device selects one of two code paths depending on the driver
model being used (=CONFIG_DM_SPI_FLASH). env_relocate_spec only used
the non driver-model code path. I'm unsure why, either none of the
platforms that need relocation use the driver model, or - worse - the
driver model is not yet usable when relocating.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
copy&paste code found in single/double buffered code path
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
With 3f66149d9f we no longer have a common call fdt_fixup_ethernet.
This was fine to do on PowerPC as they largely had calls already in
ft_cpu_fixup. On ARM however we largely relied on this call. Rather
than introduce a large number of changes to ft_cpu_fixup /
ft_board_fixup we recognize that this is a common enough call that we
should be doing it in a central location. Do it early enough that we
can do any further updates in ft_cpu_fixup / ft_board_fixup.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Thomas Chou <thomas@wytron.com.tw> (maintainer:NIOS)
Cc: York Sun <york.sun@nxp.com> (maintainer:POWERPC MPC85XX)
Cc: Stefan Roese <sr@denx.de> (maintainer:POWERPC PPC4XX)
Cc: Simon Glass <sjg@chromium.org>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Fixes: 3f66149d9f ("Remove extra fdt_fixup_ethernet() call")
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With DM_SCSI enabled, blk_create_devicef() is called with blkz = 0, leading
to a divide-by-0 exception.
scsi_detect_dev() can be used to get the required parameters (block size
and number of blocks) from the drive before calling blk_create_devicef().
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We might want to get information about the scsi device without initializing the partition.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is a cosmetic change. target and LUN have kind of the same role in
this function. One of them was passed as a parameter and the other was
embedded in a structure. For consistency, pass both of them as parameters.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This fixes a regression caused by
commit 07b2b78ce4
dm: usb: Convert USB storage to use driver-model for block devs
which caused part_init to be called when it was not previously.
Without this patch, the following happens when a USB sd card reader is used.
=> usb start
starting USB...
USB0: Port not available.
USB1: USB EHCI 1.00
scanning bus 1 for devices... 3 USB Device(s) found
scanning usb for storage devices... Device NOT ready
Request Sense returned 02 3A 00
### ERROR ### Please RESET the board ###
This happens because dev_desc->blksz is 0.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
This allows us to use the same DRAM init function on all archs. Add a
dummy function for arc, which does not use DRAM init here.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Dummy function on nios2]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move U-Boot private data into a separate file. This
lets export fw_env.h to be used by external programs
that want to change the environment using the library
built in tools/env.
Signed-off-by: Stefano Babic <sbabic@denx.de>
aes.h is a too generic name if this file can
be exported and used by a program.
Rename it to avoid any conflicts with
other files (for example, from openSSL).
Signed-off-by: Stefano Babic <sbabic@denx.de>
FIT support in the net boot case is much like the RAM boot case in that
we load our image to "load_addr" and pass a dummy read function into
"spl_load_simple_fit()". As the load address is no longer hard-coded to
the final execution address, legacy image loading will require load_addr
to be set correctly in the image header.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Under the plethora of #ifdefs, the xyzModem code hid this pearl:
static char *zm_out = (char *) 0x00380000;
This was only enabled when DEBUG is defined, so it's probably why it
went unnoticed for so long. No idea what platform had memory at that
exact location, but the this approach is extremely hacky.
Use a static buffer instead.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
spl_mmc.c calls mmc_initialize(). This symbol is provided in
drivers/mmc/mmc.c when CONFIG_GENERIC_MMC is enabled.
The sunxi Kconfig case is an oddball because it redefines
SPL_MMC_SUPPORT.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
[trini: Update arch/arm/cpu/armv8/zynqmp/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
The default value of BOOTSTAGE_STASH_SIZE should be set to hexadecimal,
but an integer value is set. This fixes the BOOTSTAGE_STASH_SIZE number
from hexadecimal to integer.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
On ARM v7M, the processor will return to ARM mode when executing blx
instruction with bit 0 of the address == 0. Always set it to 1 to stay
in thumb mode.
Similar commit:
f99993c108
Author: Matt Porter <mporter@konsulko.com>
Date: Tue May 5 15:00:23 2015 -0400
common/cmd_boot: keep ARM v7M in thumb mode during do_go_exec()
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
ft_cpu_setup() already calls fdt_fixup_ethernet(), calling it
in image_setup_libfdt() is both redundant and breaks any modifications
done by ft_board_setup(). Restore the old behavior by removing
the call in image_setup_libfdt()
Fixes: 13d06981a9 ("image: Add device tree setup to image library")
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
SPL has been restricted to use only dev 0 based on the assumption that only
one MMC device is registered. This is not always the case and many
platforms now register several devices as expected by the spl mmc boot code
For those platform SPL_ENV_SUPPORT is broken if dev is forced to 0.
A word of warning: this commit may break SPL_ENV_SUPPORT on platforms that
do not register the same MMC controllers in SPL and in u-boot (mostly iMX6
based platforms). Fortunately none of those activate SPL_ENV_SUPPORT in
their default configuration.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The environment location is something that might change per board
(depending on what storage options are availaible there) or depending on
the user choice (when we have several options).
Instead of hardcoding it in our configuration header, create a Kconfig
choice with the options we use for now, and the symbols that depend on it.
Once done, also remove the irrelevant sunxi defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
With d53ecad92f some unused interrupt related code was removed.
However all of these options are currently unused. Rather than migrate
some of these options to Kconfig we just remove the code in question.
The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename
and move the value local to the code in question.
Fixes: d53ecad92f ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
Signed-off-by: Tom Rini <trini@konsulko.com>
These includes don't seem to be needed now. Drop them. Reserve the
mp.h header for PowerPC for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: York Sun <york.sun@nxp.com>
This header file is used by three archs. It could be used by all of them
since relocation is a common function. Move it into a generic file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header file is used by two archs. It could be used by all of them
since it allows the cache to be on during relocation. Move it into a
generic file.
Signed-off-by: Simon Glass <sjg@chromium.org>
We don't need this PPC-specific function in generic code. Move it to
the powerpc directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Drop headers which are not used or needed in this file. The compiler.h
header is included by common.h.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move the ugly #ifdefs inside the reserve_video() function so we can
collect all this init into one place.
Signed-off-by: Simon Glass <sjg@chromium.org>
The arch-specific details of the cache being off are best handled inside
the reserve_mmu(). This cleans up the init sequence a little.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
CONFIG_ALT_LB_ADDR is really a detail of how this logbuffer is allocated
rather than whether to do it at all. So move the #ifdef into the function.
Signed-off-by: Simon Glass <sjg@chromium.org>
All archs put U-Boot at the bottom of the relocated region. Xtensa does
not, but perhaps not for any good reason. Adjust it to see if things
still work OK.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
At present we misuse print_cpuinfo() do so CPU init on x86. This is done
because it is the next available call after the console is enabled. But
several arches use checkcpu() instead. Despite the horrible name (which
we can fix), it seems a better choice.
Adjust the various x86 CPU implementations to move their init code into
checkcpu() and use print_cpuinfo() only for printing CPU info.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move these two function calls into checkcpu(), which is called on this
arch immediately after these two.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
We don't need a special hook for sandbox as one of the later ones will do
just as well. We can print error messages about bad options after we
print the banner. In fact, it seems better.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Combine the conditions so this appears in the init list only once.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
More than half of the architectures use this function so let's make them
all use it.
For those which don't actually define it, we can rely on the weak function
in lib/time.c
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
There is no good reason to use a different name on PowerPC. Change it to
timer_init() like the others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that both branches of the #if do the same thing, we can unify them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
We really don't need to have a name like this in the generic init
sequence. Use the generic get_clocks() name so that we can merge these
two at some point.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
We have two chunks of code which depend on this CONFIG options. There is
likely no need to keep them apart, so join them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
While x86 is the only user and this could in principle be moved to
arch_cpu_init() there is some justification for this being a separate
call. It provides a way to handle init which is not CPU-specific, but
must happen before the CPU can be set up.
Rename the function to be more generic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There is no need to have this call in the generic init sequence and no
other architecture has needed it in the time it has been there. Move it
into sandbox's private code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Add nand_size() function to move the nand size print into initr_nand().
Remove nand size print from nand_init() to allow other function to call
nand_init() without printing nand size.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The Raspberry Pi device tree files since Linux v4.9 have a "ethernet"
alias pointing to the on-board Ethernet device node. However,
U-Boot's fdt_fixup_ethernet() only looks at ethernet aliases ending
in digits.
As the spec doesn't mandate that aliases must end in numbers and there
have been much older uses of an "ethernet" aliases in the wild
(according to Tom Rini), change the code to accept "ethernet" as well.
Without this Linux isn't told of the MAC address provided by the
RPI firmware and the ethernet interface is always assigned a random MAC
address.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Certain boards come in different variations by way of utilizing daughter
boards, for example. These boards might contain additional chips, which
are added to the main board's busses, e.g. I2C.
The device tree support for such boards would either, quite naturally,
employ the overlay mechanism to add such chips to the tree, or would use
one large default device tree, and delete the devices that are actually
not present.
Regardless of approach, even on the U-Boot level, a modification of the
device tree is a prerequisite to have such modular families of boards
supported properly.
Therefore, we add an option to make the U-Boot device tree (the actual
copy later used by the driver model) writeable, and add a callback
method that allows boards to modify the device tree at an early stage,
at which, hopefully, also the application of device tree overlays will
be possible.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Calls to IS_ENABLED() on a non-y/n option will always be false, even
when set. We can correct this by adding a new bool value that is set
based on the conditions required for SPL_STACK_R_MALLOC_SIMPLE_LEN to be
set instead.
Fixes: 340f418acd ("spl: Add spl_early_init()")
Reported-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Changes in v2:
- Fix thinko pointed out by Lokesh
Non-FIT SPL image loading support should be disabled for TI secure
devices as the image handlers for those image types do not follow
our secure boot flow.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a Kconfig option that enables Legacy image support, this allows
boards to explicitly disable this, for instance when needed for
security reasons.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Move to common/spl/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_SPL_ABORT_ON_RAW_IMAGE causes SPL to abort and move on when it
encounters RAW images, express this same functionality as a positive
option enabling support for RAW images: CONFIG_SPL_RAW_IMAGE_SUPPORT
Also move uses of this to defconfigs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Rework Kconfig logic a little, move to common/spl/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
This includes support for rk3188 from Heiko Stübner and and rk3328 from
Kever Yang. Also included is SPL support for rk3399 and a fix for
rk3288 to get it booting again (spl_early_init()).
At present malloc_base/_limit/_ptr are not initialised in spl_init() when
we call spl_init() in board_init_f(). This is due to a recent change aimed
at avoiding overwriting the malloc area set up on some boards by
spl_relocate_stack_gd().
However if CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN is not defined, we now
skip setting up the memory area in spl_init() which is obviously wrong.
To fix this, add a new function spl_early_init() which can be called in
board_init_f().
Fixes: b3d2861e (spl: Remove overwrite of relocated malloc limit)
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Rewrote spl_{,early_}init() to avoid duplicate code:
Rewrite/expand commit message:
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.
Signed-off-by: York Sun <york.sun@nxp.com>
Passing NULL to fs_read() for actread value results in hanging U-Boot
at least on our ARM plattform (TI AM335x). Since fs_read() and
following functions do not catch nullpointers, writing to 0x0 occurs.
Passing a local dummy var instead of NULL solves this issue.
Signed-off-by: Jonathan Golder <jonathan.golder@kurz-elektronik.de>
Cc: Anatolij Gustschin <agust@denx.de>
Added SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION and
SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION to Kconfig.
Due to SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION being moved to
Kconfig the board defconfigs for db-88f6820-gp_defconfig
kc1_defconfig and sniper_defconfig need to be updated.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
the socfpga bootrom supports mmc booting from either a raw image
starting at 0x0, or from a partition of type 0xa2. This patch
adds support for locating the boot image in the first type 0xa2
partition found.
Assigned a partition number of -1 will cause a search for a
partition of type CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_TYPE
and use it to find the u-boot image
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
The whole of common/flash.c is guarded by #if defined() ... #endif.
Move the conditional to common/Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.
During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.
This commit was created as follows:
[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.
[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"
[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'
[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'
[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The default values for the configuration defines CONFIG_ENV_SPI_xxx are
arbitrary values. It makes more sense to set them to the values used by
the sf command.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
fdt_fixup_mtdparts currently does nothing when partition info is
runtime-generated or compiled-in defaults are used.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Fix nits in commit message:
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit 674bb24982 ("net: cosmetic: Replace magic numbers in arp.c with
constants") introduced a nice define to replace the magic value 6 for
the ethernet hardware address. Replace more hardcoded instances of 6
which really reference the ARP_HLEN (iow the MAC/Hardware/Ethernet
address).
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The BSS region may overlap with relocations. If we clear BSS we will
overwrite the start of the relocation area. This doesn't matter when running
from SPI flash, since it is read-only. But when relocating 64-bit U-Boot
from one place in RAM to another, relocation will fail because some of its
relocations have been zeroed.
To fix this, put the ELF fixup call before the BSS clearing call.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since 'gd' is just a normal variable on 64-bit x86, it is relocated by the
time we get to board_init_r(). The old 'gd' variable is passed in as
parameter to board_init_r(), presumably for this situation.
Assign it on 64-bit x86 so that gd points to the correct data.
Options to improve this:
- Make gd a fixed register and remove the board_init_r() parameter
- Make all archs use this board_init_r() parameter
The second has a TODO in the code. The first has a TODO in a future commit
('x86: Support global_data on x86_64')
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These tables should be declared static const. Unfortunately the table in
board_r is updated on machines with manual relocation.
Update them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust the code so that 64-bit startup works. Since we don't need to do CAR
changes in U-Boot proper anymore (they are done in SPL) we can simplify the
flow and return normally from board_init_f().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add an option for building Platorm Controller Hub drivers in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new Kconfig option to allow timer drivers to be used in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new Kconfig option to allow RTC drivers to be used in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new Kconfig option to allow PCI drivers to be used in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new Kconfig option to allow CPU drivers to be used in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This currently fails silently. Add a debug message to aid debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
CONFIG_CONSOLE_MUX and CONFIG_SYS_CONSOLE_IS_IN_ENV are not applicable
for SPL. Update the console code to use CONFIG_IS_ENABLED(), so that these
options will be inactive in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Boot ROM supports authentication feature to prevent malformed
software from being run on products. The signature is added at the
tail of the second stage loader (= SPL in U-boot terminology).
The size of the second stage loader was 64KB, and it was consistent
across SoCs. The situation changed when LD20 SoC appeared; it loads
80KB second stage loader, and it is the only exception.
Currently, CONFIG_SPL_PAD_TO is set to 64KB and U-Boot proper is
loaded from the 64KB offset of non-volatile devices. This means the
signature of LD20 SoC (located at 80KB offset) corrupts the U-Boot
proper image.
Let's move the U-Boot proper image to 128KB offset. It uses 48KB
for nothing but padding, and we could actually locate the U-Boot
proper at 80KB offset. However, the power of 2 generally seems a
better choice for the offset address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit 8c36e99f21.
There is misunderstanding in commit 8c36e99f21 ("armv8: release
slave cores from CPU_RELEASE_ADDR"). How to bring the slave cores
into U-Boot proper is platform-specific. So, it should be cared
in SoC/board files instead of common/spl/spl.c. As you see SPL
is the acronym of Secondary Program Loader, there is generally
something that runs before SPL (the First one is usually Boot ROM).
How to wake up slave cores from the Boot ROM is really SoC specific.
So, the intention for the spin table support is to bring the slave
cores into U-Boot proper in an SoC specific manner. (this must be
done after relocation. see below.)
If you bring the slaves into SPL, it is SoC own code responsibility
to transfer them to U-Boot proper. The Spin Table defines the
interface between a boot-loader and Linux kernel. It is unrelated
to the interface between SPL and U-Boot proper.
One more thing is missing in the commit; spl_image->entry_point
points to the entry address of U-Boot *before* relocation. U-Boot
relocates itself between board_init_f() and board_init_r(). This
means the master CPU sees the different copy of the spin code than
the slave CPUs enter. The spin_table_update_dt() protects the code
*after* relocation. As a result, the slave CPUs spin in unprotected
code, which leads to unstable behavior.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
spl_init on some boards is called after stack and heap relocation, on
some platforms spl_relocate_stack_gd is called to handle setting the
limit to its value CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN when simple
SPL malloc is enabled during relocation. spl_init should then not
re-assign the old pre-relocation limit when this is defined.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This option should not really be user selectable. Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
Move all of the status LED feature to drivers/led/Kconfig.
The LED status definitions were moved from the board configuration
files to the defconfig files.
TBD: Move all of the definitions in the include/status_led.h to the
relevant board's defconfig files.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Instead of disabling the data cache in the bootelf command, disabling
it in the do_bootm_qnxelf function.
Some ELF binary might want the cache enabled.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
We can make the code read more easily here by simply using memset()
always as when we don't have an optimized version of the function we
will still have a version of this function around anyhow.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We have long had available optimized versions of the memset and memcpy
functions that are borrowed from the Linux kernel. We should use these
in normal conditions as the speed wins in many workflows outweigh the
relatively minor size increase. However, we have a number of places
where we're simply too close to size limits in SPL and must be able to
make the size vs performance trade-off in those cases.
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
These files are only included for build by the make system
when CONFIG_SPL_{EXT,FAT}_SUPPORT is enabled, remove the unneed
checks for these in the source files.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
IEC 80000-13:2008 Quantities and units
Part 13: Information science and technology
defines the prefixes to use for binary multiples.
So instead of writing
Data Size: 6726132 Bytes = 6568.49 kB = 6.41 MB
in dumpimage we should write
Data Size: 6726132 Bytes = 6568.49 KiB = 6.41 MiB.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In 35fc84f, bootm was refactored so plain 'bootm' and
'bootm <subcommand>' shared a common implementation.
The 'bootm ramdisk' command implementation is now part of the common
implementation but not invoke by plain 'bootm' since the original
implementation never did ramdisk relocation. Instead, ramdisk
relocation happened in image_setup_linux() which is typically called
during the OS portion of 'bootm'.
On ARM, parameters to the Linux kernel can either be passed by FDT or
ATAGS. When using FDT, image_setup_linux() is called which also triggers
ramdisk relocation. When using ATAGS, image_setup_linux() is _not_
called because it mostly does FDT setup.
Instead of calling image_setup_linux() in both FDT and ATAGS cases,
include BOOTM_STATE_RAMDISK in the requested states during a plain
'bootm' if CONFIG_SYS_BOOT_RAMDISK_HIGH is set and remove the ramdisk
relocation from image_setup_linux(). This causes ramdisk relocation to
happen on any system where CONFIG_SYS_BOOT_RAMDISK_HIGH regardless of
the OS being booted. Also remove IMAGE_ENABLE_RAMDISK_HIGH as it was
only used by the now-removed code from image_setup_linux().
Signed-off-by: Rick Altherr <raltherr@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
By enabling DM_USB information about number of storage devices
was lost.
Get this information back simply by printing number of devices detected
via BLK uclass.
For example:
scanning bus 0 for devices... 7 USB Device(s) found
scanning usb for storage devices... 3 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When using ARMv8 with ARMV8_SPIN_TABLE=y, we want the slave cores to
wait on spin_table_cpu_release_addr, until the Linux kernel will "wake" them
by writing to that location. The address of spin_table_cpu_release_addr is
transferred to the kernel using the device tree that is updated by
spin_table_update_dt().
However, if we also use SPL, then the slave cores are stuck at
CPU_RELEASE_ADDR instead and as a result, never wake up.
This patch releases the slave cores by writing spl_image->entry_point to
CPU_RELEASE_ADDR location before the end of the SPL code
(at jump_to_image_no_args()).
That way, the slave cores will start to execute the u-boot and will get to
the spin-table code and wait on the correct address
(spin_table_cpu_release_addr).
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new top-level config option so support booting an image stored
in RAM. This allows to move the RAM boot support into a sparate file
and having a single condition to compile that file.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
There is no CONFIG_OF_PLATDATA, only CONFIG_SPL_OF_PLATDATA, so rename
the two references to CONFIG_OF_PLATDATA to CONFIG_SPL_OF_PLATDATA.
Signed-off-by: Tom Rini <trini@konsulko.com>
SPLASH_STORAGE_RAW is defined as 0, so a check against & will
never be true. These flags are never combined so do a check
against == instead.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable support for loading a splash image from within a FIT image.
The image is assumed to be generated with mkimage -E flag to hold
the data external to the FIT.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
New scan should unbind all block devices not to be listed again.
Without this patch if scsi reset or scan is called new block devices are
created which point to the same id and lun.
For example:
ZynqMP> scsi scan
scsi_scan: if_type=2, devnum=0: sdhci@ff170000.blk, 6, 0
scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 0
scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 1
scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 2
scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 3
scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 4
scanning bus for devices...
Device 0: (1:0) Vendor: ATA Prod.: KINGSTON SVP200S Rev: 501A
Type: Hard Disk
Capacity: 57241.8 MB = 55.9 GB (117231408 x 512)
Reported-by: Ken Ma <make@marvell.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since entry_point and load_addr are addresses, they should be
represented as longs to cover the whole address space and to avoid
warning when compiling the SPL in 64-bit.
Also adjust debug prints to add the 'l' specifier, where needed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
When we want to use Secure Boot with HAB from SPL over U-Boot.img,
we need to append the IVT to the image and leave space for the CSF.
Images generated as firmware_ivt can directly be signed using the
Freescale code signing tool. For creation of a CSF, mkimage outputs
the correct HAB Blocks for the image.
The changes to the usual firmware image class are quite small,
that is why I implemented that directly into the default_image.
Cc: sbabic@denx.de
v2-Changes: None
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Stop boot process if fpga programming fails.
Without this patch boot process continues even if fpga programming
failed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All sata based drivers are bind and corresponding block
device is created. Based on this find_scsi_device() is able
to get back block device based on scsi_curr_dev pointer.
intr_scsi() is commented now but it can be replaced by calling
find_scsi_device() and scsi_scan().
scsi_dev_desc[] is commented out but common/scsi.c heavily depends on
it. That's why CONFIG_SYS_SCSI_MAX_DEVICE is hardcoded to 1 and symbol
is reassigned to a block description allocated by uclass.
There is only one block description by device now but it doesn't need to
be correct when more devices are present.
scsi_bind() ensures corresponding block device creation.
uclass post_probe (scsi_post_probe()) is doing low level init.
SCSI/SATA DM based drivers requires to have 64bit base address as
the first entry in platform data structure to setup mmio_base.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The most of ethernet drivers are using this mdio registration sequence.
strcpy(priv->bus->name, "emac");
mdio_register(priv->bus);
Where driver can be used only with one MDIO bus because only unique
name should be used.
Other drivers are using unique device name for MDIO registration to
support multiple instances.
snprintf(priv->bus->name, sizeof(bus->name), "%s", name);
With DM dev->seq is used more even in logs
(like random MAC address generation:
printf("\nWarning: %s (eth%d) using random MAC address - %pM\n",
dev->name, dev->seq, pdata->enetaddr);
)
where eth%d prefix is used.
Simplify driver code to register mdio device with dev->seq number
to simplify mdio registration and reduce code duplication across
all drivers. With DM_SEQ_ALIAS enabled dev->seq reflects alias setting.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Create a boot_from_devices() function to handle trying each device. This
helps to reduce the size of the already-large board_init_r() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to name each method so that we can print out this name when
using the method. Currently this happens using a separate function. In
preparation for unifying this, add a name to each method.
The name is only available if we have libcommon support (i.e can use
printf()).
Signed-off-by: Simon Glass <sjg@chromium.org>
The most of ethernet drivers are using this mdio registration sequence.
strcpy(priv->bus->name, "emac");
mdio_register(priv->bus);
Where driver can be used only with one MDIO bus because only unique
name should be used.
Other drivers are using unique device name for MDIO registration to
support multiple instances.
snprintf(priv->bus->name, sizeof(bus->name), "%s", name);
With DM dev->seq is used more even in logs
(like random MAC address generation:
printf("\nWarning: %s (eth%d) using random MAC address - %pM\n",
dev->name, dev->seq, pdata->enetaddr);
)
where eth%d prefix is used.
Simplify driver code to register mdio device with dev->seq number
to simplify mdio registration and reduce code duplication across
all drivers. With DM_SEQ_ALIAS enabled dev->seq reflects alias setting.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
For example:
Board: Xilinx Zynq
Net: ZYNQ GEM: e000b000, phyaddr 7, interface rgmii-id
Warning: ethernet@e000b000 (eth0) using random MAC address -
7a:fc:90:53:6a:41
eth0: ethernet@e000b000ZYNQ GEM: e000c000, phyaddr ffffffff, interface
rgmii-id
Warning: ethernet@e000c000 (eth3) using random MAC address -
1a:ff:d7:1a:a1:b2
, eth3: ethernet@e000c000
** Bad device size - mmc 0 **
Checking if uenvcmd is set ...
Hit any key to stop autoboot: 0
Zynq> mdio list
eth0:
17 - Marvell 88E1111S <--> ethernet@e000b000
eth3:
17 - Marvell 88E1111S <--> ethernet@e000c000
Zynq>
All sata based drivers are bind and corresponding block
device is created. Based on this find_scsi_device() is able
to get back block device based on scsi_curr_dev pointer.
intr_scsi() is commented now but it can be replaced by calling
find_scsi_device() and scsi_scan().
scsi_dev_desc[] is commented out but common/scsi.c heavily depends on
it. That's why CONFIG_SYS_SCSI_MAX_DEVICE is hardcoded to 1 and symbol
is reassigned to a block description allocated by uclass.
There is only one block description by device now but it doesn't need to
be correct when more devices are present.
scsi_bind() ensures corresponding block device creation.
uclass post_probe (scsi_post_probe()) is doing low level init.
SCSI/SATA DM based drivers requires to have 64bit base address as
the first entry in platform data structure to setup mmio_base.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Series-changes: 2
- Use CONFIG_DM_SCSI instead of mix of DM_SCSI and DM_SATA
Ceva sata has never used sata commands that's why keep it in
SCSI part only.
- Separate scsi_scan() for DM_SCSI and do not change cmd/scsi.c
- Extend platdata
Series-changes: 3
- Fix scsi_scan return path
- Fix header location uclass-internal.h
- Add scsi_max_devs under !DM_SCSI
- Add new header device-internal because of device_probe()
- Redesign block device creation algorithm
- Use device_unbind in error path
- Create block device with id and lun numbers (lun was there in v2)
- Cleanup dev_num initialization in block device description
with fixing parameters in blk_create_devicef
- Create new Kconfig menu for SATA/SCSI drivers
- Extend description for DM_SCSI
- Fix Kconfig dependencies
- Fix kernel doc format in scsi_platdata
- Fix ahci_init_one - vendor variable
Series-changes: 4
- Fix Kconfig entry
- Remove SPL ifdef around SCSI uclass
- Clean ahci_print_info() ifdef logic
The patch
"dm: spl: mmc: Support CONFIG_BLK in SPL MMC"
(sha1: 87bce4e5c0)
converted FAT part of spl_mmc_do_fs_boot() but forget to update also EXT
part by 's/&mmc->block_dev/mmc_get_blk_desc(mmc)/'.
This patch is fixing compilation error when CONFIG_SPL_EXT_SUPPORT
is enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
After an image is selected out of a FIT blob for further processing we
run an optional, platform specific, post-processing function on this
component. This post-processing may modify the position and size of the
image, so after post-processing we update the location and size for this
image in the FIT header. This can cause problems as the position of
subsequent components in the FIT blob are only referenced by relative
position to the end of the last component. When we resize or move a
component the following components position will be calculated
incorrectly. To fix this, we do not update the FIT header but instead
only update our local understanding of the image data. This also allows
us to re-run post-processing steps if needed.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Carlos Hernandez <ceh@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add a new image type representing Trusted Execution Environment (TEE)
image types. For example, an OP-TEE OS binary image.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To help automate the loading of custom image types we add the ability
to define custom handlers for the loadable section types. When we find
a compatible type while loading a "loadable" image from a FIT image we
run its associated handlers to perform any additional steps needed for
loading this image.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit e2f88dfd2d ("libfdt: Introduce new ARCH_FIXUP_FDT option")
allows us to skip memory setup of DTB, but a problem for ARM is that
spin_table_update_dt() and psci_update_dt() are skipped as well if
CONFIG_ARCH_FIXUP_FDT is disabled.
This commit allows us to skip only fdt_fixup_memory_banks() instead
of the whole of arch_fixup_fdt(). It will be useful when we want to
use a memory node from a kernel DTB as is, but need some fixups for
Spin-Table/PSCI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed build error for x86:
Signed-off-by: Simon Glass <sjg@chromium.org>
When CONFIG_SPL_STACK_R is enabled, and spl_init() is called before
board_init_r(), spl_relocate_stack_gd() will move global_data to a new
place in memory. This affects driver model since it uses a list for the
uclasses. Unless this is updated the list will become invalid. When
looking for a non-existent uclass, such as when adding a new one, the loop
in uclass_find() may continue forever, thus causing a hang.
Add a function to correct this rather obscure bug.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since a platform conversion to generic board support has not been
accomplished some architecture specific bits are missing from board_f
init sequence, the change adds a number of basic expected callbacks
into early init sequence.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When blk_create_device() is called some parameters in blk_desc are
automatically filled. Separate SCSI private initialization and SCSI full
block device initialization not to rewrite already prepared data.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With DM_SCSI this function will return more than one return value to
cover errors.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Several functions should be static because they are not exported to any
other file.
Warnings were reported by sparse C=1.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These functions are not called for any location.
This patch removes them scsi_trim_trail(), scsi_get_disk_count()
and scsi_setup_read6().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no reason to directly point to static allocated array
when we have proper block_dev pointer available via parameter
in !CONFIG_BLK. For CONFIG_BLK this is read directly from uclass
platdata.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
pccb is pointer to temporary buffer which is used only for sending
command. Make it local as is done in scsi_read/scsi_write.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Prepare LUN(Logical unit number) directly in block description structure
and reuse it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch enables running detection algorithm on block device
description structure.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Extract block device initialization to specific function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is confusing that mdio commands work and report phy id as
decimal value when mii is working with hex values.
For example:
ZynqMP> mdio list
gem:
21 - TI DP83867 <--> ethernet@ff0e0000
ZynqMP> mdio read ethernet@ff0e0000 0
Reading from bus gem
PHY at address 21:
0 - 0x1140
ZynqMP> mii dump 21 0
Incorrect PHY address. Range should be 0-31
...
ZynqMP> mii dump 15
0. (1140) -- PHY control register --
(8000:0000) 0.15 = 0 reset
U-Boot normally takes hex values that's why this patch is changing mdio
command to handle hex instead of changing mii command to handle decimal
values.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Make the spl_mmc_load_image() available globally, so it can be
invoked directly by SPL on extremely space-constrained systems.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Add new configuration option CONFIG_MMC_TINY which strips away all
memory allocation within the MMC code and code for handling multiple
cards. This allows extremely space-constrained SPL code use the MMC
framework.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Enable initr_trap hook also for MIPS to install and enable
U-Boot's specific MIPS exception handlers.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If CONFIG_SPL_LIBCOMMON_SUPPORT is not defined there is a lone case statement
at the end of the switch leading to a compile error.
Remove the offending case statement.
| common/spl/spl_mmc.c:339:7: error: label at end of compound statement
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Vasut <marex@denx.de>
Introduce USB Gadget config option. This allows to combine Makefile
entries for SPL_USBETH_SUPPORT and SPL_DFU_SUPPORT.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Ravi Babu <ravibabu@ti.com>
The DFU Kconfig menu entries should be part of the SPL
Kconfig file. Also avoid using the top level Makefile by
moving the config dependent build artifacts to the driver/
and driver/usb/gadget/ Makfiles.
With that, DFU can be built again in SPL if
CONFIG_SPL_DFU_SUPPORT is enabled.
Fixes: 6ad6102246 ("usb:gadget: Disallow DFU in SPL for now")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Some devices (e.g. dra7xx) support loading to RAM using DFU without
having direct boot from RAM support. Make sure the linker list
does not contain BOOT_DEVICE_RAM if CONFIG_SPL_RAM_DEVICE is not
enabled.
Fixes: 98136b2f26 ("spl: Convert spl_ram_load_image() to use linker list")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
This fixes the loop delay when using a hw watchdog.
In case a watchdog is used that accesses CPU registers,
the defined delay of 20us in a tight loop will cause a
huge delay in the actual timeout seen. This is caused
by the fact that udelay will inheritantly call WATCHDOG_RESET.
Together with the omap wdt implementation, the seen timeout increases up to
around 30s. This makes the loop very slow and causes long
delays when using the modem.
Instead, implement the 2 sec loop by using the timer interface to know
when to break out of the timeout loop. Watchdog kicking is taken care of
by getc().
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Commit d97dc8a0 separated the non-command code into its own file
which caused variable sata_curr_device can not be set to a correct
value.
Before commit d97dc8a0, variable sata_curr_device can be set
correctly in sata_initialize().
After commit d97dc8a0, sata_initialize() is moved out to its own file.
Accordingly, variable sata_curr_device is removed from sata_initialize()
too. This caused sata_curr_device never gets a chance to be set properly
which prevent other commands from being executed.
This patch sets variable sata_curr_device properly.
Fixes: d97dc8a0 (dm: sata: Separate the non-command code into its
own file)
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make show_board_info() a weak function which allows for custom board
specific implementations thereof.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Drop CONFIG_CUSTOM_BOARDINFO as it is not Kconfig compliant and anyway
not really used anywhere plus the upcoming weak show_board_info()
approach seems much superior.
This reverts commit a9ad18c9d5.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Add check for FDT_MAGIC, otherwise also legacy images will be loaded as
a FIT. With this check in place, the loader works correct both
with legacy and FIT images.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The current code assumes that the devices are ordered corresponding to
their alias value. But (for example) video1 can come before video0 in the
device tree.
Correct this, by always looking for device 0 first. After that we can fall
back to finding the first available device.
Signed-off-by: Simon Glass <sjg@chromium.org>
While we move some config macros to Kconfig, kconfig header is needed
to avoid compiling error if not already included.
Signed-off-by: York Sun <york.sun@nxp.com>
Commit ec6617c3 includes autoconf.h in image-fit.c, causing conflict
for board odroid-xu3 which overwrites CONFIG_SYS_BOARD in header
file. Move the include higher and use linux/kconfig.h instead of
generated/autoconf.h.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
To support loading a 32-bit OS, the execution state will change from
AArch64 to AArch32 when jumping to kernel.
The architecture information will be got through checking FIT image,
then U-Boot will load 32-bit OS or 64-bit OS automatically.
Signed-off-by: Ebony Zhu <ebony.zhu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove the need to explicitly add SHA/RSA pairings. Invalid SHA/RSA
pairings will still fail on verify operations when the hash length is
longer than the key length.
Follow the same naming scheme "checksum,crytpo" without explicitly
defining the string.
Indirectly adds support for "sha1,rsa4096" signing/verification.
Signed-off-by: Andrew Duda <aduda@meraki.com>
Signed-off-by: aduda <aduda@meraki.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cut down on the repetition of algorithm information by defining separate
checksum and crypto structs. image_sig_algos are now simply pairs of
unique checksum and crypto algos.
Signed-off-by: Andrew Duda <aduda@meraki.com>
Signed-off-by: aduda <aduda@meraki.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Padding verification was done against static SHA/RSA pair arrays which
take up a lot of static memory, are mostly 0xff, and cannot be reused
for additional SHA/RSA pairings. The padding can be easily computed
according to PKCS#1v2.1 as:
EM = 0x00 || 0x01 || PS || 0x00 || T
where PS is (emLen - tLen - 3) octets of 0xff and T is DER encoding
of the hash.
Store DER prefix in checksum_algo and create rsa_verify_padding
function to handle verification of a message for any SHA/RSA pairing.
Signed-off-by: Andrew Duda <aduda@meraki.com>
Signed-off-by: aduda <aduda@meraki.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Support was already implemented, but not hooked up. This fixes several
fails in the test cases.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Coverity complains that this can overflow. If we later increase the size
of one of the strings in the table, it could happen.
Adjust the code to protect against this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Coverity (CID: 150964)
- Add DEFAULT_FDT_FILE kconfig entry
- Move CONFIG_DEFAULT_FDT_FILE from include/configs to defconfigs
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This converts the following to Kconfig:
CONFIG_SYS_STDIO_DEREGISTER
This option should never be enabled in SPL, so use
CONFIG_IS_ENABLED(SYS_STDIO_DEREGISTER) when checking the option.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Re-sync]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_INFO_QUIET
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default n, re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_ENV_OVERWRITE
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_IS_IN_ENV
CONFIG_CONSOLE_MUX
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Re-order, re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move these option to Kconfig and tidy up existing uses.
The Power PC boards don't have a suitable common element: the common header
files don't appear to line up with the Kconfig files as far as I can tell.
This results in a lot of defconfig changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
[trini: Re-migrate, update common/console.c logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
Hardware: CM-FX6 Module from Compulab
This patch fixes unwanted watchdog resets while the user enters
a command at the U-Boot prompt.
As found on the CM-FX6 board from Compulab, when having enabled the
watchdog, a missing WATCHDOG_RESET call in common/console.c causes
this and alike boards to reset when the watchdog's timeout has
elapsed while waiting at the U-Boot prompt.
Despite the user could press several keys within the watchdog
timeout limit, the while loop in cli_readline.c, line 261, does only
call WATCHDOG_RESET if first == 1, which gets set to 0 in the 1st
loop iteration. This leads to a watchdog timeout no matter if the
user presses keys or not.
Although, this affects other boards as well as it touches
common/console.c, the macro WATCHDOG_RESET expands to {} if watchdog
support isn't configured. Hence, there's no harm caused and no need to
surround it by #ifdef in this case.
* Symptom:
U-Boot resets after watchdog times out when in commandline prompt
and watchdog is enabled.
* Reasoning:
When U-Boot shows the commandline prompt, the following function
call stack is executed while waiting for a keypress:
common/main.c:
main_loop => common/cli.c: cli_loop() =>
common/cli_hush.c:
parse_file_outer => parse_stream_outer =>
parse_stream => b_getch(i) =>
i->get(i) => file_get =>
get_user_input => cmdedit_read_input =>
uboot_cli_readline =>
common/cli_readline.c:
cli_readline => cli_readline_into_buffer =>
cread_line => getcmd_getch (== getc) =>
common/console.c:
fgetc => console_tstc
common/console.c:
(with CONFIG_CONSOLE_MUX is set)
- in console_tstc line 181:
If dev->tstc(dev) returns 0, the global tstcdev variable doesn't get
set. This is the case if no character is in the serial buffer.
- in fgetc(int file), line 297:
Program flow keeps looping because tstcdev does not get set.
Therefore WATCHDOG_RESET is not called, as mx_serial_tstc from
drivers/serial/serial_mxc.c does not call it.
* Solution:
Add WATCHDOG_RESET into the loop of console_tstc.
Note: Macro expands to {} if not configured, so no #ifdef is needed.
* Comment:
Signed-off-by: Christian Storm <christian.storm@tngtech.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Andreas J. Reichel <Andreas.Reichel@tngtech.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move SYS_OS_BASE to Kconfig and cleanup existing
uses.
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Also migrate a4m2k]
Signed-off-by: Tom Rini <trini@konsulko.com>
The signature for this macro has changed. Bring in the upstream version and
adjust U-Boot's usages to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update to drivers/power/pmic/palmas.c:
Signed-off-by: Keerthy <j-keerthy@ti.com>
Change-Id: I6cc9021339bfe686f9df21d61a1095ca2b3776e8
These have now landed upstream. The naming is different and in one case the
function signature has changed. Update the code to match.
This applies the following upstream commits by
Thierry Reding <treding@nvidia.com> :
604e61e fdt: Add functions to retrieve strings
8702bd1 fdt: Add a function to get the index of a string
2218387 fdt: Add a function to count strings
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes devicetree nodes and or properties are added out of the u-boot
console, maybe through some script or manual interaction.
The devicetree as loaded or embedded is quite small, so the devicetree
has to be resized to take up those new nodes/properties.
In original the devicetree was only extended by effective
4 * add_mem_rsv.
With this commit we can add an argument to the "fdt resize" command,
which takes the extrasize to be added.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Simon Glass <sjg@chromium.org>
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures. Migrate all config files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default
in certain architectures. Migrate all config files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This is already called earlier, from fdtdec_setup(), so drop this unnecessary
call from the init sequence.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present all video devices are probed on start-up. It would be better to
probe a device only when it is needed. This can happen if it is referenced
in the stdout environment variable, for example.
Add support for this by searching for a suitable device when needed, probing
it, and finding the stdio device it creates.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
By default saveenv option is not supported for SPL. This patch
enable the support for save environment variable for SPL build.
Enable save environment support in SPL after setenv. By default
the saveenv option is not provided in SPL, but some boards need
this support in 'Falcon' boot, where SPL need to boot from
different images based on environment variable set by OS. For
example OS may set "reboot_image" environment variable to
"recovery" inorder to boot recovery image by SPL. The SPL read
"reboot_image" and act accordingly and change the reboot_image
to default mode using setenv and save the environemnt.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Simon Glass <sig@chromium.org>
change in v1:
- dropped SUPPORT, use CONFIG_SPL_SAVEENV
- updates the comments in mmc_private.h
When CONFIG_SILENT_CONSOLE is defined and the default environment has
silent=1 it is not possible for a user to make the console un-silent if
the environment is not available when console_init_f() is called (for
example because the environment is in SPI).
Add a new helper function console_update_silent() and call it from both
console_init_f() and console_init_r().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix various misspellings of:
* deprecated
* partition
* preceding,preceded
* preparation
* its versus it's
* export
* existing
* scenario
* redundant
* remaining
* value
* architecture
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
There is no need for this to be in the BSS region. By moving it we can delay
use of BSS in SPL. This is useful for machines where the BSS region is not
in writeable space. On 64-bit x86, SPL runs from SPI flash and it is easier
to eliminate BSS use than link SPL to run with BSS at a particular
cache-as-RAM (CAR) address.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the fat loader to avoid using the spl_image global variable.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the ext loader to avoid using the spl_image global variable.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Rather than having a global variable, pass the spl_image as a parameter.
This avoids BSS use, and makes it clearer what the function is actually
doing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
