U-Boot cannot be built for h2200_defconfig with CONFIG_DM=y.
The maintainer Lukasz Dalek suggested to remove the board.
https://lists.denx.de/pipermail/u-boot/2019-August/380685.html
Cc: Lukasz Dalek <luk0104@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[trini: As this is the last non-toradex PXA board, update travis too]
Signed-off-by: Tom Rini <trini@konsulko.com>
When running SPL on iMX8, the A core starts at address 0
which is a alias to OCRAM 0x100000.
The alias only map first 96KB of OCRAM, so this require the
SPL size can't beyond 96KB. But when using SPL DM, the size increase
significantly and may exceed 96KB.
So to fix the problem, we will change SPL linker address to OCRAM
address 0x100000. And then jump to the absolute address not the PC relative
address for entering OCRAM.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Probe ZynqMP firmware driver on the board initialization phase and
ensure that firmware is in place to continue execution. The probing is
done on board_init so it can be used for both SPL and U-Boot proper.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zynqmp-power driver for ZynqMP to handle the communication with the PMU
firmware. Firmware driver just probes subnodes and power driver handles
communication with PMU using the IPI mailbox driver.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define board_late_init which performs bootmode detection
and prepares corresponding distro boot commaand sequence.
Also disable it for mini platforms because simply there is no need to have
it enabled.
But also disable it for virtual platform because Qemu is not modelling this
register space that's why travis testing would fail. This configuration
should be reverted when mainline Qemu is updated.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At present there is only one control for this and it is used for both SPL
and TPL. But SPL might have a lot more space than TPL so the extra cost of
a full printf() might be acceptable.
Split the option into two, providing separate SPL and TPL controls. The
TPL setting defaults to the same as SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This reverts commit fc04b92354 where the
FVP DRAM configuration was added.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Add imply for FDT overlay that can be usefuill for kernel device tree
management but it is not mandatory (can be removed to gain space)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This converts the following to Kconfig:
CONFIG_ARCH_CPU_INIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>
Several options are presenting themselves on a various boards
where the options are clearly not used. (ie, arm64 options on
arm9, or SPL/TPL options when SPL or TPL are not defined)
This patch is not attempting to be a complete list of items, but
more like low hanging fruit.
This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.
Signed-off-by: Adam Ford <aford173@gmail.com>
Select BOARD_LATE_INIT for ls1028ardb and ls1028aqds targets
so that late init work can be done.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This commit adds board support for Hikey960 board from Hisilicon. This
board is one of the Consumer Edition boards of the 96Boards family
powered by Kirin960 SoC.
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/hikey960/
The initial supported/tested devices include:
- Debug serial
- SD
With these support, it's good enough for loading Linux Kernel from SD.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.
It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.
Supported boot media: microSD card (via SPL), QSPI flash.
Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which
is 64 MB in size and has an erase sector size of 256KB (therefore,
flashing the RCW would erase part of U-Boot).
Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which
is only 32 MB in size but has an erase sector size of 64KB (therefore
the RCW image can be flashed without erasing U-Boot).
To avoid the problems above, the U-Boot base address has been selected
at 0x100000 (the start of the 5th 256KB erase sector), which works for
all board revisions. Actually 0x40000 would have been enough, but
0x100000 is common for all Layerscape devices.
eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but
SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is
disabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Jianchao Wang <jianchao.wang@nxp.com>
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
[Vladimir] Code taken from https://github.com/openil/u-boot (which
itself is mostly copied from ls1021a-iot) and adapted with the following
changes:
- Add a008850 errata workaround
- Converted eTSEC, MMC to DM to avoid all build warnings
- Plugged in distro boot feature, including support for extlinux.conf
- Added defconfig for QSPI boot
- Added the board/freescale/ls1021atsn/README.rst for initial setup
- Increased CONFIG_SYS_MONITOR_LEN so that the SPL malloc pool does not
get overwritten during copying of the u-boot.bin payload from MMC to
DDR.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This moves sysreset support for socfgpa from ad-hoc code in mach-socfpga
to a UCLASS_SYSRESET based dm driver.
A side effect is that gen5 and a10 can now select between cold and warm
reset.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
If U-Boot is loaded and started from TF-A (you need to change
SYS_TEXT_BASE to 0x60000000), it will hang up at flash initialization.
If secure mode is off (default, or -machine virt,secure=off) at qemu,
it will provide dtb with two flash memory banks:
flash@0 {
bank-width = <0x4>;
reg = <0x0 0x0 0x0 0x4000000 0x0 0x4000000 0x0 0x4000000>;
compatible = "cfi-flash";
};
If secure mode is on, on the other hand, qemu provides dtb with 1 bank:
flash@0 {
bank-width = <0x4>;
reg = <0x0 0x4000000 0x0 0x4000000>;
compatible = "cfi-flash";
};
As a result, flash_init()/flash_get_size() will eventually fail.
With this patch applied, relevant CONFIG values are modified.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently, CONFIG_TFABOOT is located in armv8/fsl-layerscape Kconfig,
but it will be also useful for other targets if some additional
configuration are necessary.
So move it to arch/arm/Kconfig.
Please note that CONFIG_TFABOOT still depends on
CONFIG_ARCH_SUPPORT_TFABOOT and so the menu won't come up
if any target doesn't need its own customization for TF-A boot.
This will maintain the compatibility.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Sriram Dash <sriram.dash@nxp.com>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Peng Ma <peng.ma@nxp.com>
Cc: Yuantian Tang <andy.tang@nxp.com>
Cc: Pankit Garg <pankit.garg@nxp.com>
Probably for no particular reason SUNXI_GPIO was still defined the "old
way", in header files only.
Introduce SUNXI_GPIO to the Kconfig file in drivers/gpio to remove
another line from our dreadful config_whitelist.txt.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
By default, CONFIG_SYS_INIT_SP_BSS_OFFSET was made invisible by not
giving a prompt to it.
The only way to define it is to hard-code an extra entry in SoC/board
Kconfig, like arch/arm/mach-tegra/tegra{186,210}/Kconfig.
Add a prompt to it in order to allow defconfig files to specify the
value of CONFIG_SYS_INIT_SP_BSS_OFFSET.
With this, CONFIG_SYS_INIT_SP_BSS_OFFSET would become always visible.
So, we need a new bool option to turn it off by default.
I move the 'default 524288' to the common place. This value is not too
big, but is big enough to avoid the overwrap of DT in most platforms.
If 512KB is not a suitable choice for your platform, you can change it
from your defconfig or menuconfig etc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
- LS1046AFRWY support
- USB errata fix and secure boot defconfig support for LS1028A
- Enabled SDHC and SATA for LX2160
- LS1046A serdes fixes
- other minor fixes
Per discussion on the list, drop this board again.
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_SYS_[DI]CACHE_OFF had been partially converted to Kconfig
parameters; only for the ARC architecture. This patch turns these two
parameters into Kconfig items everywhere else they are found.
All of the include/configs/* and defconfig changes in this patch are
for arm machines only. The Kconfig changes for arc, nds32, riscv,
and xtensa have been included since these symbols are found in code
under arch/{arc,nds32,riscv,xtensa}, however, no currently-defined
include/configs/* or defconfigs for these architectures exist which
include these symbols.
These results have been confirmed with tools/moveconfig.py.
Acked-by: Alexey Brodkin <abrodkin@snopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Re-migrate for a few more boards]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some options like TPL_SYS_THUMB_BUILD, TPL_USE_ARCH_MEMCPY
and TPL_USE_ARCH_MEMCPY are needed for TPL build in 32bit arm.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add platform code and DTs for Renesas RZ/A1 R7S72100 SoC.
Distinguishing feature of this SoC is that it has up to
10 MiB of on-SoC static RAM (SRAM).
The DTs are imported from Linux 5.0.11, commit d5a2675b207d .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Select the PL310 UCLASS_CACHE driver for SoCFPGA.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
-----BEGIN PGP SIGNATURE-----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=CzWQ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190426' of git://git.denx.de/u-boot-imx
Porting to DM and i.MX8
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
All Rockchip SoCs use DEBUG_UART_BOARD_INIT to init per board
UART IOMUX, enable it by default.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
K3 devices have High Security (HS) variants along with the non-HS already
supported. Like the previous generation devices (OMAP/Keystone2) K3
supports boot chain-of-trust by authenticating and optionally decrypting
images as they are unpacked from FIT images. Add support for this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
This commit moves common config options used in all socfpga boards
to select/imply in Kconfig. This both cleans up the defconfig files
as well as makes future changes easier.
Options implied/defaulted for all sub-arches:
- SPL, SPL_DM, USE_TINY_PRINTF, NR_DRAM_BANKS
Options implied/defaulted for implied for A10 & gen5:
- FPGA_SOCFPGA, SYS_MALLOC_F_LEN, SYS_TEXT_BASE
Options implied/defaulted for gen5:
- SPL_STACK_R, SPL_SYS_MALLOC_SIMPLE, SPL_STACK_R_ADDR
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
- Enable DM_MMC if MMC defined
- Enable DM_SCSI if SCSI defined
globally through Allwinner platform, the effected SoC families
and boards will make use of MMC and SCSI subsystems in driver-model.
Tested DM_MMC in one board from A64, H6, H5, H3, R40, A83T, A20, A10
SoCs.
Tested-by: Pablo Sebastián Greco <pgreco@centosproject.org> # BPI-M2-Ultra
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Activate the command poweroff by default for STM32MP1:
- with PCSI from TF-A for trusted boot
- with PMIC sysreset request for basic boot (SYSRESET_POWER)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Set board name with the first dts compatible found in DT
code under CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
The result with DEVICE_TREE=stm32mp157c-ev1 is:
STM32MP> env print
board=stm32mp1
board_name=stm32mp157c-ev1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of trusted boot, using TF-A as first stage bootloader,
The boot sequence is
BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32
The TF-A monitor provides secure monitor with support of SMC
- proprietary to manage secure devices (BSEC for example)
- PSCI for power
The same device tree is used for STMicroelectronics boards with
basic boot and with trusted boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The ISW_ENTRY_ADDR Kconfig option under mach-omap2 isn't a SoC specific
notion but rather "where is our previous stage loaded in memory?"
option. Make use of this on ARCH_KEYSTONE rather than SPL_TEXT_BASE for
our HS builds that are not using SPL anyhow.
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com?
Enabling DM_MMC is forcing CONFIG_BLK=y so if any board which uses
SCSI must need to enable DM_SCSI otherwise SCSI reads on that particular
target making invalid reading to the disk drive.
Allwinner platform do support SCSI on A10, A20 and R40 SoC's out of
these only A10 have DM_SCSI enabled. So enabling DM_MMC on A20, R40
would eventually end-up with scsi disk read failures like [1]
So, enable DM_MMC in all places of respective SoC's instead of enabling
them globally to Allwinner platform.
Now, DM_MMC is enabled in Allwinner SoC's except A20 and R40.
[1] https://lists.denx.de/pipermail/u-boot/2019-April/364057.html
Reported-by: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
remove SCSI and SCSI_AHCI configs for ls1043ardb due to no sata interface
support.
this changed is to fixed the ls1043ardb compile warning as fallows:
===================== WARNING ======================
This board does not use CONFIG_DM_SCSI. Please update
the storage controller to use CONFIG_DM_SCSI before the
v2019.07 release. Failure to update by the deadline may
result in board removal.See doc/driver-model/MIGRATION.txt
for more info.
====================================================
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[PK: reword the patch subject]
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This add the initial support of the broadcom reference
board bcm963158 with a bcm63158 SoC.
This board has 1 GB of ram, 512 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This add the initial support of the broadcom bcm63158 SoC family,
only the cpu, dram and uart are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Enable DM_MMC for all Allwinner SoCs, this will eventually
enable BLK.
Also removed DM_MMC enablement in few parts of sunxi
configurations.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.
Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.
Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f24036)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CLK and DM_RESET drivers are now available for all of
the Allwinner platforms, so enable them in arch/arm/Kconfig
Enabling CLK will select DM_RESET by default.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
There is no code for using partition labels in the Allwinner SPL port.
Even so the name is slightly misleading, CONFIG_SPL_LIBDISK_SUPPORT was
meant to guard partition code for the SPL.
Remove the "imply" line in the Kconfig to make this obvious and avoid
unneeded code inclusions, helping to keep the H6 SPL code small.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch allows smaller binaries.
This is needed for and has been tested on Arndale board, as u-boot.bin is
now bigger than the 512K load limit, with GCC8, without thumb mode.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
For a small SPL, it should be possible to build without SPI(-flash) drivers
or wihout MMC drivers.
For this to work, we have to change from 'select'ing options to 'imply'ing
them.
With this change, I can have SPL trimmed to my hard-wired starting method
(SPI-NOR or MMC) while still including all drivers in U-Boot.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Using CONFIG_DM_USB for this purpose prevents using DM_USB for host and not
for device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Set environment variable 'platform' containing the CPU type.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This adds a general board file based on MT7629 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
BSS section was all the time separated for SPL but this symbol wasn't
enabled. It is necessary to have it enabled for OF_SEPARATE
configuration where DTB is appended to u-boot with DTB.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This add the initial support of the broadcom bcm6858 SoC family,
only the cpu, dram and uart are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This adds a Kconfig file in the board directory, so that some
board-specific options can be specified there.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable modern fitImage format on sunxi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Using imply for SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION instead of
select ensures we can build without partition support (used to build
a network boot only version of SPL and U-Boot).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The explicit arch specific build symbol allows to group supported
boards, generalize common config options and it will serve as
a dependency for platform only drivers.
Two related board defconfigs are resynced after the change.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Xilinx is introducing Versal, an adaptive compute acceleration platform
(ACAP), built on 7nm FinFET process technology. Versal ACAPs combine
Scalar Processing Engines, Adaptable Hardware Engines, and Intelligent
Engines with leading-edge memory and interfacing technologies to deliver
powerful heterogeneous acceleration for any application. The Versal AI
Core series has five devices, offering 128 to 400 AI Engines. The series
includes dual-core Arm Cortex™-A72 application processors, dual-core Arm
Cortex-R5 real-time processors, 256KB of on-chip memory with ECC, more
than 1,900 DSP engines optimized for high-precision floating point with
low latency.
The patch is adding necessary infrastructure in place without enabling
platform which is done in separate patch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Virtual machine provided by qemu-arm has a ARM PL031 Real Time Clock
device. With this patch, the driver is enabled by default.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
It is not preferred to put SUNXI-specific code in the common place.
Change it to 'imply' property of ARCH_SUNXI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Remove ad-hoc ethernet syscon registers configuration and reset support.
Reset is now handled by the reset framework and the syscon registers are
set in the dwmac_socfpga.c driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Use MVEBU_SPL_BOOT_DEVICE_* to select between SPI and MMC, instead of
board specific symbols. This commit enables the boot device selection
menu to all mvebu platforms, but it is only effective on Turris Omnia
and gdsys Controlcenter DC platforms. A following commit will enable
boot selection for other platforms.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
CMD_DM is used for debug purpose and it shouldn't be enabled by default
via Kconfig. Unfortunately this is in the tree for quite a long time
that's why solution is to use imply DM for all targets which are
enabling DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Fix Kconfig bool, default, select and imply options to be
alphabetically sorted.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Trivial Kconfig cleanup. Use tabs instead of spaces and every Kconfig
entry should be separated by newline.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Switch to the distro boot for UniPhier platform.
- Remove the environment vairalbes used to load images from raw
block devices.
- Keep the command to download images via tftp. This will be
useful to boot the kernel when no valid kernel image is ready
yet in the file system.
- Use root.cpio.gz instead of root.cpio.uboot because we always know
the file size of the init ramdisk; it is loaded via either a file
system or network.
- Rename fit_addr_r to kernel_addr_r, which the distro command
checks to get the load address of FIT image.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit bfc6bae8fa
This commit rename CONFIG_SPL_RESET_SUPPORT to CONFIG_SPL_DM_RESET. Update
with new CONFIG name and enable CONFIG_SPL_DM_RESET when CONFIG_DM_RESET is enabled.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
The Shared Memory Manager driver implements an interface for allocating
and accessing items in the memory area shared among all of the
processors in a Qualcomm platform.
Adapted from the Linux driver (4.17)
Changes from the original Linux driver:
* Removed HW spinlock mechanism, which is irrelevant
in U-boot particualar use case, which is just reading from the smem.
* Adapted from Linux driver model to U-Boot's.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch basically adds two new commands for loadig secure
images.
1. zynq rsa adds support to load secure image which can be both
authenticated or encrypted or both authenticated and encrypted
image in xilinx bootimage(BOOT.bin) format.
2. zynq aes command adds support to decrypt and load encrypted
image back to DDR as per destination address. The image has
to be encrypted using xilinx bootgen tool and to get only the
encrypted image from tool use -split option while invoking
bootgen.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot needs to link ps7_init_gpl.c on Zynq or psu_init_gpl.c on
ZynqMP (PS init for short). The current logic to locate this file for
both platforms is:
1. if a board-specific file exists in
board/xilinx/zynq[mp]/$(CONFIG_DEFAULT_DEVICE_TREE)/ps?_init_gpl.c
then use it
2. otherwise use board/xilinx/zynq/ps?_init_gpl.c
In the latter case the file does not exist in the U-Boot sources and
must be copied in the source tree from the outside before starting the
build. This is typical when it is generated from Xilinx tools while
developing a custom hardware. However making sure that a
board-specific file is _not_ found (and used) requires some trickery
such as removing or overwriting all PS init files (e.g.: the current
meta-xilinx yocto layer).
This generates a few problems:
* if the source tree is shared among different out-of-tree builds,
they will pollute (and potentially corrupt) each other
* the source tree cannot be read-only
* any buildsystem must add a command to copy the PS init file binary
* overwriting or deleting files in the source tree is ugly as hell
Simplify usage by allowing to pass the path to the desired PS init
file in kconfig variable XILINX_PS_INIT_FILE. It can be an absolute
path or relative to $(srctree). If the variable is set, the
user-specified file will always be used without being copied
around. If the the variable is left empty, for backward compatibility
fall back to the old behaviour.
Since the issue is the same for Zynq and ZynqMP, add one kconfig
variable in a common place and use it for both.
Also use the new kconfig help text to document all the ways to give
U-Boot the PS init file.
Build-tested with all combinations of:
- platform: zynq or zynqmp
- PS init file: from XILINX_PS_INIT_FILE (absolute, relative path,
non-existing), in-tree board-specific, in board/xilinx/zynq[mp]/
- building in-tree, in subdir, in other directory
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add build support for Stratix SoC
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Conflicts:
arch/arm/Kconfig
arch/arm/mach-socfpga/Kconfig
Add support for loading U-Boot on the Broadcom 7445 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
This commit adds uCRobotics Bubblegum-96 board support. This board is
one of the 96Boards Consumer Edition platform based on Actions Semi
S900 SoC.
Features:
- Actions Semi S900 SoC (4xCortex A53, Power VR G6230 GPU)
- 2GiB RAM
- 8GiB eMMC, uSD slot
- WiFi, Bluetooth and GPS module
- 2x Host, 1x Device USB port
- HDMI
- 20-pin low speed and 40-pin high speed expanders, 6 LED, 3 buttons
U-Boot will be loaded by ATF at EL2 execution level. Relevant driver
support will be added in further commits.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This commit adds Actions Semi OWL SoC family support with S900 as the
first target SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
As recommended by Arm in [1], ACTLR[0] (Enable invalidates of BTB)
needs to be set[2] for BTB to be invalidated on ICIALLU. This needs to
be done unconditionally for Cortex-A15 processors. Provide a config
option for platforms to enable this option based on impact analysis
for products.
NOTE: This patch in itself is NOT the final solution, this requires:
a) Implementation of v7_arch_cp15_set_acr on SoCs which may not
provide direct access to ACR register.
b) Operating Systems such as Linux to provide adequate workaround in the
right locations.
c) This workaround applies to only the boot processor. It is important
to apply workaround as necessary (context-save-restore) around low
power context loss OR additional processors as necessary in either
firmware support OR elsewhere in OS.
[1] https://developer.arm.com/support/security-update
[2] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438c/BABGHIBG.html
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andre Przywara <Andre.Przywara@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
As recommended by Arm in [1], IBE[2] has to be enabled unconditionally
for BPIALL to be functional on Cortex-A8 processors. Provide a config
option for platforms to enable this option based on impact analysis
for products.
NOTE: This patch in itself is NOT the final solution, this requires:
a) Implementation of v7_arch_cp15_set_acr on SoCs which may not
provide direct access to ACR register.
b) Operating Systems such as Linux to provide adequate workaround in the right
locations.
c) This workaround applies to only the boot processor. It is important
to apply workaround as necessary (context-save-restore) around low
power context loss OR additional processors as necessary in either
firmware support OR elsewhere in OS.
[1] https://developer.arm.com/support/security-update
[2] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0344k/Bgbffjhh.html
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andre Przywara <Andre.Przywara@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Added the following:
1. defconfig for LS1012AFRWY Secure boot
2. PfE Validation support
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE
MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
[yorks: rebase and fix SPDX tag]
[yorks: fix board/freescale/ls1012afrdm/Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to
drivers/fastboot.
Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants
FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split
USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing
behaviour.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support of fuse command (read/write/program/sense)
on bank 0 to access to BSEC SAFMEM (4096 OTP bits).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
- The correct way to build with thumb mode is to select SYS_THUMB_BUILD
- We should be setting -march=armv7-m in arch/arm/Makefile not the
sub-config.mk file.
Signed-off-by: Tom Rini <trini@konsulko.com>
- spl_board_init is empty on smartweb so drop that function
- When CONFIG_AT91SAM9_WATCHDOG is set we do not disable the watchdog in
SPL and instead let full U-Boot handle it. Instead of an empty
function just do not call a function.
Signed-off-by: Tom Rini <trini@konsulko.com>
Pull the serial port configuration from DT and use DM serial instead
of having the serial configuration in two places, DT and board config.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Shuffle the default Kconfig entries around so it is not such a mess.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Move CONFIG_MX31 from mx31pdk.h to mx31pdk_defconfig and introduce
necessary Kconfig changes as well.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Xilinx ZynqMP also contains dual Cortex R5 which can run U-Boot.
This patch is adding minimal support to get U-Boot boot.
U-Boot on R5 runs out of DDR with default configuration that's why
DDR needs to be partitioned if there is something else running on arm64.
Console is done via Cadence uart driver and the first Cadence Triple
Timer Counter is used for time.
This configuration with uart1 was tested on zcu100-revC.
U-Boot 2018.05-rc2-00021-gd058a08d907d (Apr 18 2018 - 14:11:27 +0200)
Model: Xilinx ZynqMP R5
DRAM: 512 MiB
WARNING: Caches not enabled
MMC:
In: serial@ff010000
Out: serial@ff010000
Err: serial@ff010000
Net: Net Initialization Skipped
No ethernet found.
ZynqMP r5>
There are two ways how to run this on ZynqMP.
1. Run from ZynqMP arm64
tftpb 20000000 u-boot-r5.elf
setenv autostart no && bootelf -p 20000000
cpu 4 disable && cpu 4 release 10000000 lockstep
or
cpu 4 disable && cpu 4 release 10000000 split
2. Load via jtag when directly to R5
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit moves the FPGA descriptor definition
to mach-zynq, where it makes more sense.
Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Memory Protection Unit(MPU) allows to partition memory into regions
and set individual protection attributes for each region. In absence
of MPU a default map[1] will take effect. Add support for configuring
MPU on Cortex-R, by reusing the existing support for Cortex-M processor.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0460d/I1002400.html
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Cortex-R* processors are a mid-range CPUs for use in deeply-embedded,
real-time systems. It implements the ARMv7-R architecture, and includes
Thumb-2 technology for optimum code density and processing throughput.
Except for MPU(Memory Protection Unit) and few CP15 registers, most of the
features are compatible with v7 architecture. So,reuse the same armv7
folder and introduce a new config CPU_V7R in order to differentiate
from v7 based platforms.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Certain ARM architectures like ARMv7-A, ARMv7-R has support for
enabling caches using CP15 registers. To have a common support
for all these architectures, introduce a Kconfig symbol
SYS_ARM_CACHE_CP15 that selects cache-cp15.c
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add a Kconfig entry for MMU and imply for all platforms using
cache-cp15.c containing MMU setup. Using imply instead of select so that
MMU can be disabled by defconfigs when not needed.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under
armv7 folder. This led to a misconception of creating separate folders
for armv7m and armv7r. There is no reason to create separate folder for
other armv7 based architectures when it can co-exist with few Kconfig
symbols.
As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later
separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and
can co exist in the same folder.
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
SYS_ARCH_TIMER guards the usage of the ARM Generic Timer (aka arch
timer) in U-Boot.
At the moment it is mandatory for ARMv8 and used by a few ARMv7 boards.
Add a proper Kconfig symbol to express this dependency properly,
allowing certain board configuration to later disable arch timer in case
there are any problems with it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[tuomas: rebase + fix conflicts and resync with moveconfig & use select]
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
The default of DISTRO_DEFAULTS is messy. Using the 'imply' keyword
is equivalent and cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This converts the following to Kconfig:
CONFIG_SPI
This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver. For now, just update
the CONFIG tests. This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This allows using the full SPL framework on mxs devices. In this
mode, the u-boot.sb image loaded by the boot ROM contains only the
SPL which then loads U-Boot proper or a kernel in falcon mode.
Signed-off-by: Mans Rullgard <mans@mansr.com>
All rockchip SoCs can use ns16550 driver, enable it for all
and set SYS_NS16550_MEM32 for all SoCs.
Version-changes: 2
- use imply instead of select
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add support of sysreset with generic driver "syscon-reboot"
provided by RCC, for U-boot and for SPL.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
SPL copy BootRom boot mode information
in TAMP register 21.
This TAMP register information is used
after relocation to set 2 env variables
- boot_device
- boot_instance
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch adds new command "zynqmp" to handle zynqmp
specific commands like "zynqmp secure". This secure command is
used for verifying zynqmp specific secure images. The secure
image can either be authenticated or encrypted or both encrypted
and authenticated. The secure image is prepared using bootgen
and will be in xilinx specific BOOT.BIN format. The optional
key can be used for decryption of encrypted image if user
key was specified while creation BOOT.BIN.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Watchdog is only enabled in full u-boot. Adoption for SPL should be also
done because that's the right place where watchdog should be enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- add new arch stm32mp for STM32 MPU/Soc based on Cortex A
- support for stm32mp157 SOC
- SPL is used as first boot stage loader
- using driver model for all the drivers, even in SPL
- all security feature are deactivated (ETZC and TZC)
- reused STM32 MCU drivers when it is possible
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
TI_SECURE_DEVICE is used by both OMAP2+ and Keystone2 family devices,
and so when ARCH_OMAP2PLUS was used to gate off the OMAP2+ Kconfig
Keystone2 family devices lost this config option.
Move this option out of mach-omap2 Kconfig to a spot accessible by both
families. We picked arch/arm/Kconfig over the TI specific board/ti/
location as this option is not specific to our boards but rather our
architecture.
Plus at some point this option can be changed to just
SECURE_DEVICE, as having secure parts is not exclusive to TI and
so other vendors can interpret this option as needed by their device
configurations.
Fixes: a93fbf4a78 ("ARM: omap2+: rename config to ARCH_OMAP2PLUS and consolidate Kconfig")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Kconfig should only 'select' features that are required for an arch.
Standard features that can be disabled without breaking board support
should use 'imply' instead, to allow users to disable it.
These options are changed for mach-socfpga:
- DM_SPI & DM_SPI_FLASH: only required with QSPI support enabled
- SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION: the boot rom supports a
partitionless mode also, where SPL is located at address 0
- HW_WATCHDOG: while all mainline board defconfigs use it, U-Boot
should still work without it.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
All Socfpga boards from ./include/configs/socfpga_* define
CONFIG_HW_WATCHDOG.
To ease CONFIG_HW_WATCHDOG conversion to Kconfig select it in
config ARCH_SOCFPGA (arch/arm/Kconfig) section.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
When this config is enabled, <asm/arch/boot0.h> is included,
but the Kconfig help says this should be a define
(ARM_SOC_BOOT0_HOOK).
The code for this in arch/arm/lib/vectors.s was changed on
01/02/2017 with commit ce62e57fc5 ("ARM: boot0 hook: remove macro,
include whole header file").
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Simplify SPL_LDSCRIPT config by using the new arch Kconfig
configurations ARCH_MX23 and ARCH_MX28.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
The motivation for moving MX28 selection to Kconfig is to be able
to better handle NAND MXS selection through Kconfig.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
The motivation for moving MX23 selection to Kconfig is to be able
to better handle NAND MXS selection through Kconfig.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlpxesoACgkQykllyylKDCFwngCfZfk2S+c9uJCLh1drA7a+J4Ch
G+MAnA/iRu6/Ihd5UMe4tMK8BU51h0GQ
=Ylul
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2018.03
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
There are two reasons for doing this change.
There is still !DM driver for xilinx soft gpio IP and especially it is
saving some space for memory constrained boards like cse (almost ~400B).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not enable DM_ETH/MMC if subsystems are not enabled.
This saves memory for memory constrained boards like cse.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to enable BLK by default for all boards which is just
increasing memory footprint for memory contrained boards like cse.
zc770s are also saving some space.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Commit 608b0c4ad4 ("serial: Use next serial device if probing fails")
added code to search for more serial devices if the default one was not
probed correctly.
Unfortunately, that breaks omap3_evm. So while investigating why that is
the case, let's disable the full search for everyone but bcm283x where it
is needed.
Fixes: 608b0c4ad4 ("serial: Use next serial device if probing fails")
Reported-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl01x.
Signed-off-by: Alexander Graf <agraf@suse.de>
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl011.
Signed-off-by: Alexander Graf <agraf@suse.de>
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl010.
Signed-off-by: Alexander Graf <agraf@suse.de>
fdt overlay support is useful for all sunxi boards, enable per default
and remove it from sunxi defconfigs.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Setup proper dependency in Kconfig for SPL_CLK.
If SPL is not enabled, SPL_CLK shouldn't be selected.
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds support for '-machine virt' on AArch64. This is rather simple:
we just add TARGET_QEMU_ARM_xxBIT to select a few different Kconfig
symbols, provide the ARMv8 memory map from the board file and add a new
defconfig based on the 32-bit defconfig.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII
PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Allow placing a Linux kernel image header at the start of the U-Boot
binary. This is useful since the image header reports the amount of memory
(BSS and similar) that U-Boot needs to use, but that isn't part of the
binary size. This can be used by the code that loads U-Boot into memory to
determine where to load U-Boot, based on other users of memory.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
U-Boot typically uses a hard-coded value for the stack pointer before
relocation. Implement option SYS_INIT_SP_BSS_OFFSET to instead calculate
the initial SP at run-time. This is useful to avoid hard-coding addresses
into U-Boot, so that can be loaded and executed at arbitrary addresses and
thus avoid using arbitrary addresses at runtime. This option's value is
the offset added to &_bss_start in order to calculate the stack pointer.
This offset should be large enough so that the early malloc region, global
data (gd), and early stack usage do not overlap any appended DTB.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
855873: An eviction might overtake a cache clean operation
Workaround: The erratum can be avoided by upgrading cache clean by
address operations to cache clean and invalidate operations. For
Cortex-A53 r0p3 and later release, this can be achieved by setting
CPUACTLR.ENDCCASCI to 1.
This patch is to implement the workaround for this erratum.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Use more accurate description for Xilinx Zynq and ZynqMP based platforms.
With using driver model there shouldn't be a need to create separate
Kconfig config options.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Rockchip SoCs bootrom design is like this:
- First 2KB or 4KB internal memory is for bootrom stack and heap;
- Then the first 4-byte suppose to be a TAG like 'RK33';
- The the following memory address end with '0004' is the first
instruction load and running by bootrom;
Let's use the boot0 hook to reserve the first 4-byte tag for all
the Rockchip SoCs.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Commit message taken from an older patch by:]
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This is required in the case where U-Boot is typically loaded and run at
a particular address, but for some reason the RAM at that location is not
available, e.g. due to memory fragmentation loading other boot binaries or
firmware, splitting an SMP complex between various different OSs without
using e.g. the EL2 second-stage page tables to hide the memory asignments,
or due to known ECC failures.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Currently, pylibfdt is always compiled if swig is installed on your
machine. It is really annoying because most of targets (excepts
x86, sunxi, rockchip) do not use dtoc or binman.
"checkbinman" and "checkdtoc" are wrong. It is odd that the final
build stage checks if we have built necessary tools. If your platform
depends on dtoc/binman, you must be able to build pylibfdt. If swig
is not installed, it should fail immediately.
I added PYLIBFDT, DTOC, BINMAN entries to Kconfig. They should be
property select:ed by platforms that need them. Kbuild will descend
into scripts/dtc/pylibfdt/ only when CONFIG_PYLIBFDT is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The motivation for moving MX25 selection to Kconfig is to be
able to better handle MX25 specific errata, so that an errata option
can be selected at SoC level instead of board level.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
We start to get to the limit of our main U-Boot binary size (with some
boards even crossing it). Enable its build using thumb2 to get some extra
room.
Suggested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This board builds an U-Boot binary that is bootable with QEMU's 'virt'
machine on ARM. The minimal QEMU command line is:
qemu-system-arm -machine virt,highmem=off -bios u-boot.bin
(Note that the 'highmem=off' parameter to the 'virt' machine is required for
PCI to work in U-Boot.) This command line enables the following:
- u-boot.bin loaded and executing in the emulated flash at address 0x0
- A generated device tree blob placed at the start of RAM
- A freely configurable amount of RAM, described by the DTB
- A PL011 serial port, discoverable via the DTB
- An ARMv7 architected timer
- PSCI for rebooting the system
- A generic ECAM-based PCI host controller, discoverable via the DTB
Additionally, QEMU allows plugging a bunch of useful peripherals to the PCI bus.
The following ones are supported by both U-Boot and Linux:
- To add a Serial ATA disk via an Intel ICH9 AHCI controller, pass e.g.:
-drive if=none,file=disk.img,id=mydisk -device ich9-ahci,id=ahci -device ide-drive,drive=mydisk,bus=ahci.0
- To add an Intel E1000 network adapter, pass e.g.:
-net nic,model=e1000 -net user
- To add an EHCI-compliant USB host controller, pass e.g.:
-device usb-ehci,id=ehci
- To add a NVMe disk, pass e.g.:
-drive if=none,file=disk.img,id=mydisk -device nvme,drive=mydisk,serial=foo
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
USB_GADGET will fail to compile if USB_MUSB_GADGET is not defined. Make
sure we have that condition right.
Fixes: e0ea88042d51 ("sunxi: Imply USB_ETHER")
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
GPT is pretty common these days and can be useful for things like fastboot.
Add a platform imply, so that users can still opt out if they wish so.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we can enable the usb_ether gadget, do it. This will be especially
useful for boards that don't have any ethernet controller, such as the ones
based on the A13 or A33.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fastboot need a bunch of options to be operating properly, such as the
g_dnl gadget, the fastboot command, and some options that make sense. Since
fastboot is now part of Kconfig, make sure we have them right.
That will also reduce the boilerplate in the defconfigs.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A good number of our boards have USB_GADGET enabled. Imply it so that all
the boards can benefit from it, and remove some boilerplate from our
defconfigs.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With Makefiles testing for $(SPL_TPL_)SYSRESET, we need TPL_SYSRESET
for do_reset() in TPL for Rockchip SoCs.
References: 87c16d4 "drivers: spl: consistently use the $(SPL_TPL_)
macro"
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable the Rockchip SARADC driver for all Rockchip SoCs.
Note that the SARADC peripheral is available on all SoCs except the
RK3036 and RK3228. However, as this is a DM-driver, enabling by
default will not cause any function problems (and can always be
changed from defconfig, if size is a concern).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
On ARCH_OMAP2PLUS platforms we know what the DDR layout is going to be,
and that it is safe to use SPL_STACK_R and provide a default value for
it. select this and re-sync the defconfigs.
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch add support of LS1088AQDS platform.
The LS1088A QorIQTM Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports the
LS1088A QorIQ Architecture processor.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Disabled NAND in board header file]
Reviewed-by: York Sun <york.sun@nxp.com>
WIP: disable NAND for LS1088ARDB
With Makefiles testing for $(SPL_TPL_)SYSRESET, we need SPL_SYSRESET
for do_reset() in SPL for Rockchip SoCs.
References: 87c16d4 "drivers: spl: consistently use the $(SPL_TPL_) macro"
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's
not strictly part of fastboot.
- Add some defaults for the fastboot buffer location and size
- Migrate all options listed in cmd/fastboot/Kconfig
- Cleanup the README
Signed-off-by: Tom Rini <trini@konsulko.com>
Since commit f0776a5517 ("spl: dm: Kconfig: SPL_CLK depends on
SPL_DM"), the following warning is displayed:
$ make uniphier_v8_defconfig
warning: (ARCH_ZYNQ && ARCH_ZYNQMP && STM32F7 && CLK_UNIPHIER) selects
SPL_CLK which has unmet direct dependencies (CLK && SPL_DM)
While I am here, I am removing the prompt to make it user-unconfigurable
option so that "select CLK_UNIPHIER" can be omitted.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
All boards which use DM_MMC have now been converted to use DM_MMC_OPS.
Drop the option and good riddance.
Signed-off-by: Simon Glass <sjg@chromium.org>
Under very rare timing circumstances, transitioning into streaming
mode might create a data corruption. Present on Two or more processors
or 1 core with ACP, all revisions. This erratum can be worked round
by setting bit[22] of the undocumented Diagnostic Control Register to 1.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>