Commit graph

774 commits

Author SHA1 Message Date
Lukasz Majewski
56c4046038 spi: Convert CONFIG_DM_SPI* to CONFIG_$(SPL_TPL_)DM_SPI*
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.

Before this change it was necessary to use:
    /* SPI Flash Configs */
    #if defined(CONFIG_SPL_BUILD)
    #undef CONFIG_DM_SPI
    #undef CONFIG_DM_SPI_FLASH
    #undef CONFIG_SPI_FLASH_MTD
    #endif

in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.

The goal of this patch:

Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.

Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).

In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):

- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
  run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
  environment with no fitImage and OF_LIBFDT support).

Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.

This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-29 13:34:43 -04:00
Marek Vasut
7204160315 ARM: imx: soc: Switch BOARD_EARLY_INIT_F to imply on MX7
There are systems where board_early_init_f() is plain empty. Switch
the config option from "select" to "imply", to permit user to unset
the BOARD_EARLY_INIT_F if it were to be empty.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2020-06-22 17:44:13 +02:00
Gregory CLEMENT
c7c120c22b ARM: at91: Enable SPL_SEPARATE_BSS by default
According to the linker script for both armv7 and arm926ejs based SoC,
BSS section was all the time separated for SPL but this symbol was
only enabled on some boards. However, it is necessary to have it
enabled for OF_SEPARATE configuration where DTB is appended to u-boot
with DTB.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
2020-06-18 14:28:37 +03:00
Jagan Teki
64efd11d3b arm: Remove pcm051 board
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Acked-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-11 15:14:04 +05:30
Masahiro Yamada
1517126fda ARM: uniphier: select DM_ETH
drivers/net/smc911x.c has been converted to DM.

select DM_ETH to enable it for all the UniPhier platform boards.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-05-22 11:21:06 +09:00
Trevor Woerner
71f6354b0e rename symbol: CONFIG_STM32 -> CONFIG_ARCH_STM32
Have this symbol follow the pattern of all other such symbols.

Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2020-05-15 14:47:35 -04:00
Trevor Woerner
18138ab203 rename symbol: CONFIG_TEGRA -> CONFIG_ARCH_TEGRA
Have this symbol follow the pattern of all other such symbols.

Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2020-05-15 14:47:35 -04:00
Trevor Woerner
bb0fb4c0f4 rename symbol: CONFIG_KIRKWOOD -> CONFIG_ARCH_KIRKWOOD
Have this symbol follow the pattern of all other such symbols.
This patch also removes a TODO from the code.

Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2020-05-15 14:47:35 -04:00
Trevor Woerner
b16a331697 rename symbol: CONFIG_ORION5X -> CONFIG_ARCH_ORION5X
Have this symbol follow the pattern of all other such symbols.
This patch removes a TODO from the code.

Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2020-05-15 14:47:35 -04:00
Trevor Woerner
b3d9a8b185 arm: lpc32xx: move SoC to mach-lpc32xx
Following the example of most other SoCs in arch/$(ARCH)/cpu/$(CPU)/$(SOC)
move the lpc32xx code from arch/arm/cpu/arm926ejs/lpc32xx to
arch/arm/mach-lpc32xx.

Following the checklist from
commit 01f1445630 ("ARM: prepare for moving SoC sources into mach-*"):

    [1] move files from arch/arm/cpu/arm926ejs/lpc32xx to arch/arm/mach-lpx32xx
    [2] add machine entry to arch/arm/Makefile
    [3] remove "obj-y += ..." from arch/arm/cpu/arm926ejs/Makefile
    [4] fix the Kconfig file path in arch/arm/Kconfig
    [5] (no MAINTAINERS update)

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2020-05-15 14:47:35 -04:00
Andre Przywara
56e403d95f arm: juno: enable USB
The Juno board features a standard compliant EHCI/OHCI USB host
controller pair, which we can just enable.
The platform data is taken from the device tree.

This allows to use USB mass storage (the only storage on a Juno r0)
for loading.

At least on my board USB seems a bit flaky, I need two "usb reset"
sequences after the "usb start" to detect an USB hard drive.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-05-07 09:01:42 -04:00
Andre Przywara
be0d09695d arm: juno: Use PSCI based reset
So far the Juno board wasn't implementing reset. Let's just use the
already existing PSCI_RESET based method to avoid any extra code.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-05-07 09:01:42 -04:00
Andre Przywara
b3270e9138 arm: juno: Enable OF_CONTROL
The Arm Juno board was still somewhat stuck in "hardcoded land", even
though there are stable DTs around, and one happens to actually be on
the memory mapped NOR flash.

Enable the configuration options to let the board use OF_CONTROL, and
add a routine to find the address of the DTB partition in NOR
flash, to use that for U-Boot's own purposes.
This can also passed on via $fdtcontroladdr to any kernel or EFI
application, removing the need to actually load a device tree.

Since the existing "afs" command and its flash routines require
flash_init() to be called before being usable, and this is done much
later in the boot process, we introduce a stripped-down partition finder
routine in vexpress64.c, to scan the NOR flash partitions for the
DT partition. This location is then used for U-Boot to find and probe
devices.

The name of the partition can be configured, if needed, but defaults
to "board.dtb", which is used by Linaro's firmware image provided.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-05-07 09:01:42 -04:00
Tom Rini
36c2f020f2 actions: Fix syntax for enabling SYS_RELOC_GD_ENV_ADDR
The correct syntax is 'select SYS_...' and not 'select CONFIG_SYS...'

Fixes: d5c819b885 ("actions: Move defconfig options to Kconfig")
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-01 13:30:52 -04:00
Patrick Delaunay
f8dc7f2f18 configs: migrate CONFIG_SYS_ARM_CACHE_* in Kconfig
Move CONFIG_SYS_ARM_CACHE_WRITETHROUGH and
CONFIG_SYS_ARM_CACHE_WRITEALLOC into Kconfig done by moveconfig.py.

Kconfig uses a choice between the 3 values supported in U-Boot,
including the new configuration CONFIG_SYS_ARM_CACHE_WRITEBACK
(the default configuration).

The patch also avoids to select simultaneously 2 configurations.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-05-01 11:34:01 -04:00
Michal Simek
b72f450527 ARM: zynq: Setup stack size via Kconfig
Stack size has been introduced by commit a69814c815 ("arm64: zynqmp:
Set initrd_high to as high as possible") and commit 085201c246 ("arm64:
versal: Set initrd_high to as high as possible")
to support setting up initrd_high as high as possible.
The same change should happen for Zynq because the code is moved to xilinx
common location.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-27 13:53:13 +02:00
Amit Singh Tomar
d5c819b885 actions: Move defconfig options to Kconfig
This patch moves some of the config options from bubblegum_96_defconfig
to respective Kconfig files.

Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
2020-04-24 16:40:09 -04:00
Amit Singh Tomar
8b520ac153 clk: actions: Add common clock driver
This patch converts S900 clock driver to something common that can
be used for other SoCs, for instance S700(few of clk registers are same).

Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
2020-04-24 16:40:09 -04:00
Amit Singh Tomar
b1a6bb3b59 arm: actions: Add common framework for Actions Owl Semi SoCs
This commit adds common arch support for Actions Semi Owl
series SoCs and removes the Bubblegum96 board files.

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
2020-04-24 16:40:09 -04:00
Tom Rini
e4837da782 - enable DM_RNG on meson boards
- fix SMBIOS info on Odroid-C2
 - Fix video output on GXBB/GXL/GXM boards
 - add USB gadget support for GXL/GXM boards
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAl6dk4YACgkQd9zb2sjI
 SdHMkg//ZCBy73xx98g48WqZbeKGpLzpHCYuksa+RIk90tUH2VxpSX2RFPh9F3bs
 5RbzrzDXTgTRRaDPDGS4nDhAnmNnRaGZ0SMGY+2ilt6JD/GW6x1Q3xMJt4spd0Tv
 GnA9jhExZYN0eJampGMXSZX/kO2hjLs929uA+UccxdZZx+q45SPE2Q2tSE+B/3T7
 Owf3PMPLVLyPcdxTN2HBjMKsoPbOpBxIvfwXTucnL2SJE+tBMCdDiObwWSO7nfBa
 zlEntUO0tIOgNLtqDnjQ2o71xQawFMGL0m1vpLXAaS9UUk64tnxgPQewC668X2v/
 aBU7peaA6cMkjpQ4bnWVKnJ4sLS1YdvFaz68TkFSLRHBQLr6XBGcm1biXALhrpId
 e4Rjf6ONJH+mVZtH67vRxaFJ5tpNtDj0ZFM3kzppEeFc5q1ieQ+o+TAC2KmYpi6s
 hH2t3Fs2mh+pXYC9A0eeSXG5hxWKDoT4P8/Wx3DMmDn0cMWjrEZU/yJNUVti2fhO
 8er2NldRFEYmDGAKQ1yeYzUYemZjLFuUEAVZgRaARsjl07MoG0CTqGF8Yf1NwdIT
 xMHBdpjl5iTH4jvOYS5+MqPi7hrr1OCCE9FRwx9KeagudpBzko4HiF8IW5ilQdLb
 GDDqW4RnRv8sYiNsx5cUkQSvoqPfhazawFgrJck3jLqfiVZNKog=
 =1Ffl
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-amlogic-20200420' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic

- enable DM_RNG on meson boards
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
2020-04-20 13:44:27 -04:00
Heinrich Schuchardt
6da749d8b3 arm: meson: imply DM_RNG
All ARCH_MESON boards have a hardware random number generator. So we should
enable building the RNG driver.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2020-04-15 18:06:28 +02:00
Patrick Delaunay
654706be84 configs: stm32mp1: replace STM32MP1_TRUSTED by TFABOOT
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a121 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-04-15 09:08:37 +02:00
Tom Rini
8e4af8f6d8 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq
- Fixes env variable for layerscape platforms, disable hs200.
- Fixes board fixup, mux setting, enable gic, fspi on lx2160a, Fixes I2C
  DM Warning on ls1043a, ls1046a
- Fixes RGMII port on ls1046ardb, ls1046ardb and DM_USB Warning on
  ls1012afrdm, ls1021aiot
2020-03-30 14:14:07 -04:00
Yuantian Tang
c40ebf7e43 board: ls1028ardb: add BOARD_LATE_INIT config
Select BOARD_LATE_INIT config so that many board works can be done
in late init stage.

Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30 08:06:52 +05:30
Andre Przywara
48313fe510 sunxi: Move common defconfig options to Kconfig
Some config symbols are found in *almost* every _defconfig file for
Allwinner boards, because those options are actually a platform choice,
and not a per-board decision.
Some of these options are older, some have recently been added.

Move those options to be set for all Allwinner boards in their
respective Kconfig files.

The rationales are as follows:
- NR_DRAM_BANKS: All Allwinner SoC map DRAM at one contiguous region of
  address space only, starting at 1 GB. So it's always one bank.
- SPL_{DOS,EFI}_PARTITION: The Allwinner SPL does only support raw MMC
  accesses, we don't care about filesystems or partitions in there, so
  there is no need to define those symbols at all.
- USE_PREBOOT: We start USB early when a keyboard is configured, using the
  preboot env variable, so we need to set this variable.
- SYS_RELOC_GD_ENV_ADDR: We don't specify any ENV_ADDR, so need this
  symbol to be set (according to 8d8ee47e03).
- SYS_USB_EVENT_POLL_VIA_INT_QUEUE: According to commit eab9433aa5,
  specifying this reduces the latency of the USB keyboard handling, so
  this was formerly enabled in config headers for all Allwinner boards.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-03-18 18:25:00 +05:30
Sam Shih
db41d985f6 arm: mediatek: remove unused binman config
The binman-option BINMAN_FDT is introduced by this commit:
commit 3c10dc95bd ("binman: Add a library to access binman entries")
BINMAN_FDT being selected when BINMAN=y that resulting in mt7623
and mt7622 are unable to boot. The root cause of this issue is commit:
commit cbd2fba1ec ("arm: MediaTek: add basic support for MT7629 boards")
select BINMAN=y in all mediatek SoCs, and others mediatek SoCs not
expect to use BINMAN_FDT.
This patch remove BINMAN=y option when ARCH_MEDIATEK=y and
move this to the specify SoCs part config.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
2020-03-10 17:08:13 -04:00
Stefano Babic
c82b70bcc3 imx: remove woodburn board
Board is not longer used, remove it.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2020-03-09 15:03:24 +01:00
Alex Nemirovsky
7d706a886f board: presidio-asic: Add basic G3 engr. development board support
Add basic Presidio G3 engineering board support

Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
2020-02-07 16:16:01 -05:00
Tom Rini
427da6f028 Merge tag 'u-boot-rockchip-20200130' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Support redundant boot for rk3399
- Support binman for rockchip platform
- Update ram driver and add ddr4 support for rk3328
2020-02-01 15:31:04 -05:00
Masahiro Yamada
407b01b3b3 mtd: rawnand: denali_dt: use UCLASS_MTD instead of UCLASS_MISC
UCLASS_MTD is a better fit for NAND drivers.

Make NAND_DENALI_DT depend on DM_MTD, which is needed to compile
drivers/mtd/mtd-uclass.c

Also, make ARCH_UNIPHIER select DM_MTD because all the defconfig
of this platform enables NAND_DENALI_DT.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
2020-02-01 01:14:32 +09:00
Jagan Teki
79030a4861 rockchip: Add Single boot image (with binman, pad_cat)
All rockchip platforms support TPL or SPL-based bootloader
in mainline with U-Boot proper as final stage. For each
stage we need to burn the image on to flash with respective
offsets.

This patch creates a single boot image component using
- binman, for arm32 rockchip platforms
- pad_cat, for arm64 rockchip platforms.

This would help users to get rid of burning different
boot stage images.

The new image called 'u-boot-rockchip.bin'
which can burn into flash like:

₹ sudo dd if=u-boot-rockchip.bin of=/dev/sda seek=64

This would support all rockchip platforms, except rk3128
since it doesn't support for SPL yet.

Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-01-30 11:44:01 +08:00
Alex Marginean
a2a1474674 board: fsl: ls1028a: free up arch_misc_init
Currently LS1028A board code uses arch_misc_init to set up the board mux
on QDS.  Move this code to misc_init_r.  This is consistent with LS gen 2
and T series SoCs/boards.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-24 14:28:26 +05:30
Alex Marginean
9d7df5015d board: fsl: ls1088a: remove empty arch_misc_init
The arch_misc_init function is empty on LS108x SoCs/boards, remove it.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-24 14:28:26 +05:30
Alex Marginean
196ada6a69 board: fsl: ls2080a/ls2081a: remove empty arch_misc_init
The arch_misc_init function is empty on LS2 SoCs/boards, remove it.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-24 14:28:26 +05:30
Alex Marginean
2a322ff812 board: fsl: lx2160a: free up arch_misc_init
Currently LX2 board code uses arch_misc_init to set up the board mux on
RDB and QDS.  Move this code to misc_init_r.  This is consistent with LS
gen 2 and T series SoCs/boards.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-24 14:28:26 +05:30
Philippe Reynes
645b7ec52c bcm968360bg: add initial support
This add the initial support of the broadcom reference
board bcm968360bg with a bcm68360 SoC.

This board has 512 MB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2020-01-23 07:29:58 -05:00
Philippe Reynes
6454e95f4f bcm68360: add initial support
This add the initial support of the broadcom bcm68360 SoC family.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2020-01-23 07:29:58 -05:00
Stephan Gerhold
689088f9da arm: Add support for ST-Ericsson U8500 SoC
The NovaThor U8500 SoC was released by ST-Ericsson in 2011.
It was used for some development boards like the CALAO Systems
Snowball SBC, but mass production was primarily for Android
smartphones like the Samsung Galaxy S III mini.

Previous support for U8500 was removed in
commit 68282f55b8 ("arm: Remove unused ST-Ericsson u8500 arch")
since none of the boards were converted to generic boards
before the deadline.

The new code does not have much in common with the previous code.
I have completely rewritten everything, embracing the Driver Model
and device trees wherever possible.

The U8500 support is a bit more minimal for now - my primary
use case is to use U-Boot as alternative bootloader for some of the
U8500 Samsung smartphones. At the moment U-Boot is chain-loaded from
the original Samsung bootloader. A side effect of this is that we
can (temporarily) get away without implementing some functionality
- e.g. all clocks are already enabled by the original bootloader.

More functionality will be added in future patches.

Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2020-01-22 17:47:57 -05:00
Tom Rini
92329e2413 Xilinx/FPGA changes for v2020.04
ARM64:
 - Add INIT_SPL_RELATIVE dependency
 
 SPL:
 - FIT image fix
 - Enable customization of bl2_plat_get_bl31_params()
 
 Pytest:
 - Add test for octal/hex conversions
 
 Microblaze:
 - Fix manual relocation for one SPI instance
 
 Nand:
 - Convert zynq/zynqmp drivers to DM
 
 Xilinx:
 - Enable boot script location via Kconfig
 - Support OF_SEPARATE in board FDT selection
 - Remove low level uart setup it is done later by code
 - Add support for DEVICE_TREE variable passing for SPL
 
 Zynq:
 - Enable jtag boot mode via distro boot
 - Removing unused baseaddresses from hardware.h
 - DT fixups
 
 ZynqMP:
 - Fix emmc boot sequence
 - Simplify spl logic around bss and board_init_r()
 - Support psu_post_config_data() calling
 - Tune mini-nand DTS
 - Fix psu wiring for a2197 boards
 - Add runtime MMC device boot order filling in spl
 - Clear ATF handoff handling with custom bl2_plat_get_bl31_params()
 - Add support u-boot.its generation
 - Use single image configuration for all platforms
 - Enable PANIC_HANG via Kconfig
 - DT fixups
 - Firmware fixes
 - Add support for zcu208 and zcu1285
 
 Versal:
 - Fix emmc boot sequence
 - Enable board_late_init() by default
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXiAK2AAKCRDKSWXLKUoM
 IX3VAJ41GJXBwP7Z9hX9RFhsqOu0M+NdegCdFvMUaCQ1bSvgAMOnDL+JeB21+Qo=
 =qSbv
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx/FPGA changes for v2020.04

ARM64:
- Add INIT_SPL_RELATIVE dependency

SPL:
- FIT image fix
- Enable customization of bl2_plat_get_bl31_params()

Pytest:
- Add test for octal/hex conversions

Microblaze:
- Fix manual relocation for one SPI instance

Nand:
- Convert zynq/zynqmp drivers to DM

Xilinx:
- Enable boot script location via Kconfig
- Support OF_SEPARATE in board FDT selection
- Remove low level uart setup it is done later by code
- Add support for DEVICE_TREE variable passing for SPL

Zynq:
- Enable jtag boot mode via distro boot
- Removing unused baseaddresses from hardware.h
- DT fixups

ZynqMP:
- Fix emmc boot sequence
- Simplify spl logic around bss and board_init_r()
- Support psu_post_config_data() calling
- Tune mini-nand DTS
- Fix psu wiring for a2197 boards
- Add runtime MMC device boot order filling in spl
- Clear ATF handoff handling with custom bl2_plat_get_bl31_params()
- Add support u-boot.its generation
- Use single image configuration for all platforms
- Enable PANIC_HANG via Kconfig
- DT fixups
- Firmware fixes
- Add support for zcu208 and zcu1285

Versal:
- Fix emmc boot sequence
- Enable board_late_init() by default
2020-01-16 09:45:40 -05:00
Giulio Benetti
77eb9a90dd imx: Add basic support for the NXP IMXRT10xx SoC family
Add i.IMXRT family basic support.

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14 22:54:00 +01:00
Michal Simek
f071cdab85 arm64: Enable INIT_SP_RELATIVE by default when POC is enabled
When position-independent pre-relocation code is enable there is also
necessary to enable relative early stack pointer not to use origin location
pointed by CONFIG_SYS_INIT_SP_ADDR macro.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14 09:05:53 +01:00
Bharat Kumar Reddy Gooty
0bc4356dea arch: arm: Program GIC LPI configuration table
Programs the following:
1. Redistributor PROCBASER configuration table (which
is common for all redistributors)
2. Redistributor pending table (PENDBASER), for all the
available redistributors.

Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
2020-01-10 14:18:26 -05:00
Tom Rini
ce022f2857 Merge branch 'master' of git://git.denx.de/u-boot-socfpga 2020-01-08 15:23:49 -05:00
Ley Foon Tan
a76b711dea arm: socfpga: agilex: Enable Agilex SoC build
Add build support for Agilex SoC.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2020-01-07 14:38:34 +01:00
Tom Rini
44ad496143 arm: imx: Default to SYS_THUMB_BUILD for i.MX6/7
In the case of i.MX6 and i.MX7 family SoCs it is safe (from an errata
point of view) to use thumb2 by default to save space.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-01-07 10:26:57 +01:00
Robert P. J. Day
e852b30b23 arch/arm/Kconfig: typo/grammar/punctuation fixes
Various (mostly minor) spelling, grammar and punctuation tweaks for
arch/arm/Kconfig.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2020-01-02 10:27:23 -05:00
Miquel Raynal
88718be300 mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND
Add more clarity by changing the Kconfig entry name.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-03 23:04:10 -05:00
Thomas Hebb
64eff47c78 rockchip: imply instead of selecting SPL_SYS_MALLOC_SIMPLE
We shouldn't force which allocator the SPL uses, since there's no
platform requirement for one over the other: in fact, we currently allow
selection of the TPL allocator but not the SPL one!

Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 18:51:25 +08:00
liu hao
e3aafef4cf arm: add initial support for the Phytium Durian Board
This adds platform code and the device tree for the Phytium Durian Board.
The initial support comprises the UART and the PCIE.

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>

Signed-off-by: Steven Hao <liuhao@phytium.com.cn>
2019-11-07 18:01:13 -05:00
Michal Simek
3e5476c6cd ARM: zynq: Remove unused board_early_init_f()
board_early_init_f added by commit e6cc3b25d7
("arm: zynq: Wire watchdog internals") is no longer needed that's why
remove it also with Kconfig enabling.

Fixes: ccd063e981 ("watchdog: Move watchdog_dev to data section (BSS may not be cleared)")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:03 +02:00
Heinrich Schuchardt
cb578f0a87 arm: remove the H2200 board
U-Boot cannot be built for h2200_defconfig with CONFIG_DM=y.

The maintainer Lukasz Dalek suggested to remove the board.
https://lists.denx.de/pipermail/u-boot/2019-August/380685.html

Cc: Lukasz Dalek <luk0104@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[trini: As this is the last non-toradex PXA board, update travis too]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-16 18:09:08 -04:00
Ye Li
9a2738581a imx8: Jump from alias to OCRAM address at SPL init
When running SPL on iMX8, the A core starts at address 0
which is a alias to OCRAM 0x100000.
The alias only map first 96KB of OCRAM, so this require the
SPL size can't beyond 96KB. But when using SPL DM, the size increase
significantly and may exceed 96KB.
So to fix the problem, we will change SPL linker address to OCRAM
address 0x100000. And then jump to the absolute address not the PC relative
address for entering OCRAM.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-10-13 22:49:12 +02:00
Tom Rini
44fb0d6c9f Xilinx/FPGA changes for v2020.01
FPGA:
 - Enable fpga loading on Versal
 - Minor fix
 
 Microblaze:
 - Fix LMB configurations to support initrds
 - Some other cleanups
 
 Zynq:
 - Minor config/dt changes
 - Add distro boot support for usb1 and mmc1
 - Remove Xilinx private boot commands and use only distro boot
 
 ZynqMP:
 - Kconfig cleanups, defconfig updates
 - Update some dt files
 - Add firmware driver for talking to PMUFW
 - Extend distro boot support for jtag
 - Add new IDs
 - Add system controller configurations
 - Convert code to talk firmware via mailbox or SMCs
 
 Versal:
 - Add board_late_init()
 - Add run time DT memory setup
 - Add DFU support
 - Extend distro boot support for jtag and dfu
 - Add clock driver
 - Tune mini configurations
 
 Xilinx:
 - Improve documentation (boot scripts, dt binding)
 - Enable run time initrd_high calculation
 - Define default SYS_PROMPT
 - Add zynq/zynqmp virtual defconfig
 
 Drivers:
 - Add Xilinx mailbox driver for talking to firmware
 - Clean zynq_gem for Versal
 - Move ZYNQ_HISPD_BROKEN to Kconfig
 - Wire genphy_init() in phy.c
 - Add Xilinx gii2rgmii bridge
 - Cleanup zynq_sdhci
 - dwc3 fix
 - zynq_gpio fix
 - axi_emac fix
 
 Others:
 - apalis-tk1 - clean config file
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXZ2mcwAKCRDKSWXLKUoM
 IT/KAJ4tL49YwINqCVGd7gafWvdfC4htygCcCgr9gLnJ+LjDQkxWT/r6faIcL00=
 =OnMk
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2020.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx/FPGA changes for v2020.01

FPGA:
- Enable fpga loading on Versal
- Minor fix

Microblaze:
- Fix LMB configurations to support initrds
- Some other cleanups

Zynq:
- Minor config/dt changes
- Add distro boot support for usb1 and mmc1
- Remove Xilinx private boot commands and use only distro boot

ZynqMP:
- Kconfig cleanups, defconfig updates
- Update some dt files
- Add firmware driver for talking to PMUFW
- Extend distro boot support for jtag
- Add new IDs
- Add system controller configurations
- Convert code to talk firmware via mailbox or SMCs

Versal:
- Add board_late_init()
- Add run time DT memory setup
- Add DFU support
- Extend distro boot support for jtag and dfu
- Add clock driver
- Tune mini configurations

Xilinx:
- Improve documentation (boot scripts, dt binding)
- Enable run time initrd_high calculation
- Define default SYS_PROMPT
- Add zynq/zynqmp virtual defconfig

Drivers:
- Add Xilinx mailbox driver for talking to firmware
- Clean zynq_gem for Versal
- Move ZYNQ_HISPD_BROKEN to Kconfig
- Wire genphy_init() in phy.c
- Add Xilinx gii2rgmii bridge
- Cleanup zynq_sdhci
- dwc3 fix
- zynq_gpio fix
- axi_emac fix

Others:
- apalis-tk1 - clean config file
2019-10-09 16:22:03 -04:00
Tom Rini
eaa0bde051 u-boot-imx-20191009
-------------------
 
 Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/595148532
 
 - MX6UL / ULZ
 - Toradex board
 - Allow to set OCRAM for MX6Q/D
 - MX7ULP
 - MX8: (container image, imx8mq_mek), SCU API
 - fix several board booting from SD/EMMC (cubox-i for example)
 - pico boards
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAl2dlTAPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3yfgL/1b4pKCwxswK42XkPpdHN1u/v2W/PVDanl/H
 EYxlluHVFH23bLTjLvrrgQjAnZD1VQhxWq3bwCMoJ8vb9tYQ3d9vq7XADQ0WVQV+
 EfhE33fVRPRT3rEdhDKWm+y1mL8YPvYEBnr9li7qU9n1VxiwONPXxMXMqoo9/lbM
 b6lJaG5KkuK8Ofx3cYFVQeAEdsFYIJ2aXtTqsqrV9o2sjruOuG3Ux+6Ov+9O0crY
 q8MXvW6kwWkVVNriVV7Yal0pomPZfMTqft007En9Mv2FtXqMeCWZ4Xh2LtRylR7n
 ruIbo94jkPuwuZ0p/6SeiyopoG/hU/skrkJv1s8W70DOsyaunP2BsveYXEjMV2Rb
 DomotcJit9Ws6P7rOP1oI8OvxSxVN8n6mo23UviZd8MjNAmOm49BtSxVGGB+pwmr
 ufGFG4MGQ5VpCxmzh6KrJCLXpI/mhKrkBkZy58cUbus7aPv3es/jBmmtGlU3m6ka
 NlEzHOX1hpJV/lhLvxjqRhVxuXvXOA==
 =+e3p
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20191009' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20191009
-------------------

Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/595148532

- MX6UL / ULZ
- Toradex board
- Allow to set OCRAM for MX6Q/D
- MX7ULP
- MX8: (container image, imx8mq_mek), SCU API
- fix several board booting from SD/EMMC (cubox-i for example)
- pico boards

[trini: display5 merged manually]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-09 11:44:45 -04:00
Stefano Babic
d714a75fd4 imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2019-10-08 16:36:37 +02:00
Ibai Erkiaga
325a22dc19 arm64: zynqmp: probe firmware driver
Probe ZynqMP firmware driver on the board initialization phase and
ensure that firmware is in place to continue execution. The probing is
done on board_init so it can be used for both SPL and U-Boot proper.

Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08 09:55:11 +02:00
Ibai Erkiaga
1327d1678b firmware: zynqmp: Add zynqmp-power support
zynqmp-power driver for ZynqMP to handle the communication with the PMU
firmware. Firmware driver just probes subnodes and power driver handles
communication with PMU using the IPI mailbox driver.

Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08 09:55:11 +02:00
T Karthik Reddy
a69814c815 arm64: zynqmp: Set initrd_high to as high as possible
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08 09:11:14 +02:00
Siva Durga Prasad Paladugu
085201c246 arm64: versal: Set initrd_high to as high as possible
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08 09:11:14 +02:00
Siva Durga Prasad Paladugu
bfd092f9ca arm64: versal: Define board_late_init for versal
Define board_late_init which performs bootmode detection
and prepares corresponding distro boot commaand sequence.

Also disable it for mini platforms because simply there is no need to have
it enabled.
But also disable it for virtual platform because Qemu is not modelling this
register space that's why travis testing would fail. This configuration
should be reverted when mainline Qemu is updated.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08 09:11:14 +02:00
Simon Glass
27084c03d3 spl: Allow tiny printf() to be controlled in SPL and TPL
At present there is only one control for this and it is used for both SPL
and TPL. But SPL might have a lot more space than TPL so the extra cost of
a full printf() might be acceptable.

Split the option into two, providing separate SPL and TPL controls. The
TPL setting defaults to the same as SPL.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-08 13:57:45 +08:00
Ryan Harkin
296439e0b1 Revert "vexpress64: fvp dram: add DRAM configuration"
This reverts commit fc04b92354 where the
FVP DRAM configuration was added.

Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
2019-08-31 09:27:19 -04:00
Patrick Delaunay
f219361de1 stm32mp1: configs: imply CONFIG_OF_LIBFDT_OVERLAY
Add imply for FDT overlay that can be usefuill for kernel device tree
management but it is not mandatory (can be removed to gain space)

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Adam Ford
1bf330150c Convert CONFIG_ARCH_CPU_INIT to Kconfig
This converts the following to Kconfig:
   CONFIG_ARCH_CPU_INIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>
2019-08-25 19:32:55 -04:00
Adam Ford
057055660f Kconfigs: Various: Fix some SPL, TPL and ARM64 dependencies
Several options are presenting themselves on a various boards
where the options are clearly not used.  (ie, arm64 options on
arm9, or SPL/TPL options when SPL or TPL are not defined)

This patch is not attempting to be a complete list of items, but
more like low hanging fruit.

This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-23 13:59:06 -04:00
Pankaj Bansal
a02a9421f4 armv8: ls1028aqds: define ARCH_MISC_INIT to handle mux
Define ARCH_MISC_INIT for LS1028AQDS platform to handle board
related mux.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Yuantian Tang
acf40f50b8 armv8: ls1028a: select BOARD_LATE_INIT config
Select BOARD_LATE_INIT for ls1028ardb and ls1028aqds targets
so that late init work can be done.

Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:35 +05:30
Ley Foon Tan
63b312d882 arm: socfpga: Fix SYSRESET_SOCFPGA_S10 config name
The CONFIG name should be SYSRESET_SOCFPGA_S10 instead of
SYSRESET_SOCFPGA_STRATIX10.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2019-08-15 08:50:00 +02:00
Manivannan Sadhasivam
c62c7ef779 board: hisilicon: Add support for Hikey960 board
This commit adds board support for Hikey960 board from Hisilicon. This
board is one of the Consumer Edition boards of the 96Boards family
powered by Kirin960 SoC.

More information about this board can be found in 96Boards website:
https://www.96boards.org/product/hikey960/

The initial supported/tested devices include:
 - Debug serial
 - SD

With these support, it's good enough for loading Linux Kernel from SD.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-08-11 16:43:41 -04:00
Tom Rini
92430b8fc8 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-socfpga
- Various gen5 fixes
2019-07-29 09:03:11 -04:00
Jianchao Wang
8782122052 Add support for the NXP LS1021A-TSN board
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.

It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.

Supported boot media: microSD card (via SPL), QSPI flash.

Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which
is 64 MB in size and has an erase sector size of 256KB (therefore,
flashing the RCW would erase part of U-Boot).

Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which
is only 32 MB in size but has an erase sector size of 64KB (therefore
the RCW image can be flashed without erasing U-Boot).

To avoid the problems above, the U-Boot base address has been selected
at 0x100000 (the start of the 5th 256KB erase sector), which works for
all board revisions. Actually 0x40000 would have been enough, but
0x100000 is common for all Layerscape devices.

eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but
SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is
disabled.

Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Jianchao Wang <jianchao.wang@nxp.com>
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>

[Vladimir] Code taken from https://github.com/openil/u-boot (which
itself is mostly copied from ls1021a-iot) and adapted with the following
changes:

- Add a008850 errata workaround
- Converted eTSEC, MMC to DM to avoid all build warnings
- Plugged in distro boot feature, including support for extlinux.conf
- Added defconfig for QSPI boot
- Added the board/freescale/ls1021atsn/README.rst for initial setup
- Increased CONFIG_SYS_MONITOR_LEN so that the SPL malloc pool does not
  get overwritten during copying of the u-boot.bin payload from MMC to
  DDR.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-25 13:13:31 -05:00
Simon Goldschmidt
ef72ba0b87 sysreset: add support for socfpga sysreset
This moves sysreset support for socfgpa from ad-hoc code in mach-socfpga
to a UCLASS_SYSRESET based dm driver.

A side effect is that gen5 and a10 can now select between cold and warm
reset.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-07-21 12:45:10 +02:00
AKASHI Takahiro
70a64a070e arm: qemu: fix failure in flash initialization if booting from TF-A
If U-Boot is loaded and started from TF-A (you need to change
SYS_TEXT_BASE to 0x60000000), it will hang up at flash initialization.

If secure mode is off (default, or -machine virt,secure=off) at qemu,
it will provide dtb with two flash memory banks:
	flash@0 {
		bank-width = <0x4>;
		reg = <0x0 0x0 0x0 0x4000000 0x0 0x4000000 0x0 0x4000000>;
		compatible = "cfi-flash";
	};
If secure mode is on, on the other hand, qemu provides dtb with 1 bank:
	flash@0 {
		bank-width = <0x4>;
		reg = <0x0 0x4000000 0x0 0x4000000>;
		compatible = "cfi-flash";
	};

As a result, flash_init()/flash_get_size() will eventually fail.
With this patch applied, relevant CONFIG values are modified.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-07-18 11:31:28 -04:00
AKASHI Takahiro
6324d50679 arm: move CONFIG_TFABOOT to generic Kconfig
Currently, CONFIG_TFABOOT is located in armv8/fsl-layerscape Kconfig,
but it will be also useful for other targets if some additional
configuration are necessary.
So move it to arch/arm/Kconfig.

Please note that CONFIG_TFABOOT still depends on
CONFIG_ARCH_SUPPORT_TFABOOT and so the menu won't come up
if any target doesn't need its own customization for TF-A boot.
This will maintain the compatibility.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Sriram Dash <sriram.dash@nxp.com>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Peng Ma <peng.ma@nxp.com>
Cc: Yuantian Tang <andy.tang@nxp.com>
Cc: Pankit Garg <pankit.garg@nxp.com>
2019-07-18 11:31:27 -04:00
Tom Rini
0e80dda32c Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-sunxi
- Beelink-x2 STB support (Marcus)
- H6 DDR3, LPDDR3 changes (Andre, Jernej)
- H6 pin controller, USB PHY (Andre)
2019-07-16 11:19:31 -04:00
Andre Przywara
10cfbaabc1 sunxi: move SUNXI_GPIO to Kconfig
Probably for no particular reason SUNXI_GPIO was still defined the "old
way", in header files only.

Introduce SUNXI_GPIO to the Kconfig file in drivers/gpio to remove
another line from our dreadful config_whitelist.txt.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-16 17:13:15 +05:30
Tom Rini
a9a3a37f92 - syscon: add support for power off
- stm32mp1: add op-tee config
 - stm32mp1: add specific commands: stboard and stm32key
 - add stm32 mailbox driver
 - solve many stm32 warnings when building with W=1
 - update stm32 gpio driver
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJdKK2iAAoJEOKyvdngqpN1TvcH/jj1ujNdRKn994R3DqULzFtc
 Y0WGjAciTUuV0d9gZLxPZJwlWfqxLgbmUEBlPJQJe79gaM7kNN0PgAe6GNedFhGk
 UhRR7GgbA7wogorpRo8aLe3XYEqHtgPFkf1nSiNz/AHLBg8SB20VhWcY90Kha9lh
 IJ0GK+lSdCxiyaLBC2nswnI2PS/fl4NfC7KWvujtKZduIDIOHqh5q+39llpejyuw
 WOzL/bEa4ald6JKpxOii2KXNwD1gUDQGmPzADYcIdwzJtx9hft7DBSLC5Nr+ndBz
 72TjpbtfJ/qIurv8HeXYs9mtwnCO3WP+015fog0T0zjZ48BrT1A8C96ezwLOfz0=
 =W3ny
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20190712' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm

- syscon: add support for power off
- stm32mp1: add op-tee config
- stm32mp1: add specific commands: stboard and stm32key
- add stm32 mailbox driver
- solve many stm32 warnings when building with W=1
- update stm32 gpio driver
2019-07-14 09:09:49 -04:00
Patrick Delaunay
05d3693688 stm32mp1: update package information in device tree
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12 11:18:53 +02:00
Masahiro Yamada
382de4a7e9 arm64: add an option to switch visibility of CONFIG_SYS_INIT_SP_BSS_OFFSET
By default, CONFIG_SYS_INIT_SP_BSS_OFFSET was made invisible by not
giving a prompt to it.

The only way to define it is to hard-code an extra entry in SoC/board
Kconfig, like arch/arm/mach-tegra/tegra{186,210}/Kconfig.

Add a prompt to it in order to allow defconfig files to specify the
value of CONFIG_SYS_INIT_SP_BSS_OFFSET.

With this, CONFIG_SYS_INIT_SP_BSS_OFFSET would become always visible.
So, we need a new bool option to turn it off by default.

I move the 'default 524288' to the common place. This value is not too
big, but is big enough to avoid the overwrap of DT in most platforms.
If 512KB is not a suitable choice for your platform, you can change it
from your defconfig or menuconfig etc.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
2019-07-10 22:37:23 +09:00
Tom Rini
63a4585791 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq
- LS1046AFRWY support
- USB errata fix and secure boot defconfig support for LS1028A
- Enabled SDHC and SATA for LX2160
- LS1046A serdes fixes
- other minor fixes
2019-06-19 14:01:11 -04:00
Vabhav Sharma
d90c7ac7a9 armv8: ls1046afrwy: Add support for LS1046AFRWY platform
LS1046AFRWY board supports LS1046A family SoCs. This patch
add base support for this board.
Board support's 4GB ddr memory, i2c, micro-click module,microSD card,
serial console,qspi nor flash,ifc nand flash,qsgmii network interface,
usb 3.0 and serdes interface to support two x1gen3 pcie interface.

Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19 12:54:57 +05:30
Tom Rini
9a4b90015a arm: Remove zipitz2 board
Per discussion on the list, drop this board again.

Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-06-13 12:50:55 +05:30
Patrick Delaunay
ce3772ca8d stm32mp1: migrate PREBOOT to Kconfig
Use Kconfig to activate CONFIG_PREBOOT (empty by default).

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-05-23 11:36:46 +02:00
Yuantian Tang
f278a21749 armv8: ls1028aqds: Add support of LS1028AQDS
LS1028AQDS Development System is a high-performance
computing, evaluation, and development platform that supports
LS1028A QorIQ Architecture processor.

Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-05-22 12:24:24 +05:30
Yuantian Tang
353f36d96e armv8: ls1028ardb: Add support for LS1028ARDB
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.

Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-05-22 12:24:24 +05:30
Trevor Woerner
1001502545 CONFIG_SPL_SYS_[DI]CACHE_OFF: add
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.

Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-18 08:15:35 -04:00
Trevor Woerner
a0aba8a2eb CONFIG_SYS_[DI]CACHE_OFF: convert to Kconfig
CONFIG_SYS_[DI]CACHE_OFF had been partially converted to Kconfig
parameters; only for the ARC architecture. This patch turns these two
parameters into Kconfig items everywhere else they are found.

All of the include/configs/* and defconfig changes in this patch are
for arm machines only. The Kconfig changes for arc, nds32, riscv,
and xtensa have been included since these symbols are found in code
under arch/{arc,nds32,riscv,xtensa}, however, no currently-defined
include/configs/* or defconfigs for these architectures exist which
include these symbols.

These results have been confirmed with tools/moveconfig.py.

Acked-by: Alexey Brodkin <abrodkin@snopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Re-migrate for a few more boards]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-18 08:15:34 -04:00
Kever Yang
09259fce1e sysreset: enable driver support in SPL/TPL
SPL/TPL also need use sysreset for some feature like panic callback.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08 17:34:12 +08:00
Kever Yang
1e32c5194f arm: add option for TPL support in arm 32bit
Some options like TPL_SYS_THUMB_BUILD, TPL_USE_ARCH_MEMCPY
and TPL_USE_ARCH_MEMCPY are needed for TPL build in 32bit arm.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08 17:34:12 +08:00
Chris Brandt
3529596442 ARM: dts: renesas: Add RZ/A1 platform code
Add platform code and DTs for Renesas RZ/A1 R7S72100 SoC.
Distinguishing feature of this SoC is that it has up to
10 MiB of on-SoC static RAM (SRAM).

The DTs are imported from Linux 5.0.11, commit d5a2675b207d .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-05-07 05:41:32 +02:00
Dinh Nguyen
aaa6480370 configs: socfpga: add imply pl310 cache controller
Select the PL310 UCLASS_CACHE driver for SoCFPGA.

Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
2019-05-05 08:48:50 -04:00
Tom Rini
3570ea1f98 Improvements and new features:
- improved SPI driver for better read throughput
 - refactors initialisation of debug UART init
 - restructures header file paths
 - adds pinctrl improvements
 
 Adds Kever as a co-custodian.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJcyU2hAAoJECaAFcEOcohNlFsH/3ujz7paIV34ilGGA1BQPJS7
 OOnJ7KOKkWBpwl8ai03n8/sK9kkEshZ8/PQE3E2UeWbwE9knDAREwNynYRqNwv5P
 f/6HuFZ3tCCRfVBsbTpSe4b/BxIn2zavhMQVfgd8kYaSY7dWzeaBB28GbKxfApHY
 ysNF5Q5oGMwTaL322vpFOmk/a5rHrSI8KJloDzTWxAPbNRIf3fUhwl1imSbGB6RP
 wWwuBCfbTcvw9+F4bK2W3q+umSg7o9zPwwno7Invh/nPqe5ExrVuzalRG4+1vtXe
 3jBKWTVFYX2KPDBpAfaMItehGPeGJet7+mU4GcW1FaCtlyE9QqXKfZknplCfKyU=
 =NpSn
 -----END PGP SIGNATURE-----

Merge tag 'rockchip-for-2019.07' of git://git.denx.de/u-boot-rockchip

Improvements and new features:
- improved SPI driver for better read throughput
- refactors initialisation of debug UART init
- restructures header file paths
- adds pinctrl improvements

Adds Kever as a co-custodian.
2019-05-01 11:52:04 -04:00
Tom Rini
b4ee6daad7 Porting to DM and i.MX8
------------------------
 
 - warp7 to DM
 - kp_imx53 to DM
 - Warnings in DT
 - MX8QM support
 - colibri-imx6ull to DM
 - imx7d-pico to DM
 - ocotp for MX8
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAlzDBtoPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3UpQL/ipaUejQOOr00oOgUBQqt3JCPZ7KNu8ruih/
 nIFUDrI8nP+4psaOhRp1sEPFJUxUjdIqODeAZD8zrlEi1pXNAgPWYrFRfbz54bzw
 jLsqqMz1/djQseLydQTcqZTSz8Ys7o+8OfKH64fdsZn+y9no9tHBN5hz5qWdXexN
 kbyykkg8TJC3eUyRZqKuULOqzDV9BAdASOXu7UTa04sEekLdVvS2+zkUdB6UVZTN
 LOAzm+7xY8Tey1BZxLuZUJDpHzFEMvPvlbbQRrxeDn/feZJwNgIP6hGcMeVOwOIf
 KEwFn/m/HI2JWS4taXb5aT+v3xmiQvyCC3jNW0XTf5rq02pbfgyPsVhGQIGyU2yY
 Fj7zIN7hVCLJNBpctvXyuAd1MjOlGEPIrHNjRnIZjtr7/iA1AIRn7Hg4cGNCHw6V
 5gdza3B/xFODN+Ts6O+UVIukI61MJ6mGGdNCueOnWDviNROOL82D7Jh02KfNNNxR
 q+yPsHSpo6rC1MGXv4SOReZtgpng/w==
 =CzWQ
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20190426' of git://git.denx.de/u-boot-imx

Porting to DM and i.MX8
------------------------

- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
2019-05-01 07:25:51 -04:00
Kever Yang
b0a569da08 rockchip: enable DEBUG_UART_BOARD_INIT by default
All Rockchip SoCs use DEBUG_UART_BOARD_INIT to init per board
UART IOMUX, enable it by default.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-05-01 00:00:06 +02:00
Andrew F. Davis
3a543a8084 arm: mach-k3: Add secure device support
K3 devices have High Security (HS) variants along with the non-HS already
supported. Like the previous generation devices (OMAP/Keystone2) K3
supports boot chain-of-trust by authenticating and optionally decrypting
images as they are unpacked from FIT images. Add support for this here.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
2019-04-26 17:51:51 -04:00
Parthiban Nallathambi
d8d33b6d4d imx: Add variscite DART-6UL Evaluation Kit
Port for the DART-6UL Evaluation Kit SBC. Based on the variscite
DART-6UL iMX6ULL SoM.

CPU:   Freescale i.MX6ULL rev1.1 900 MHz (running at 396 MHz)
CPU:   Commercial temperature grade (0C to 95C) at 43C
Reset cause: POR
Model: Variscite DART-6UL Evaluation Kit
Board: Variscite DART-6UL Evaluation Kit
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
In:    serial@02020000
Out:   serial@02020000
Err:   serial@02020000
Net:   FEC0

Working:
 - Eth0
 - i2c
 - MMC/SD
 - eMMC
 - USB host
 - UART 1

Note: LCDIF porting needs DM_VIDEO
https://lists.denx.de/pipermail/u-boot/2019-April/365506.html

Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
2019-04-25 19:16:24 +02:00
Simon Goldschmidt
aef44283ac arm: socfpga: imply/default common config options
This commit moves common config options used in all socfpga boards
to select/imply in Kconfig. This both cleans up the defconfig files
as well as makes future changes easier.

Options implied/defaulted for all sub-arches:
- SPL, SPL_DM, USE_TINY_PRINTF, NR_DRAM_BANKS

Options implied/defaulted for implied for A10 & gen5:
- FPGA_SOCFPGA, SYS_MALLOC_F_LEN, SYS_TEXT_BASE

Options implied/defaulted for gen5:
- SPL_STACK_R, SPL_SYS_MALLOC_SIMPLE, SPL_STACK_R_ADDR

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
2019-04-25 00:00:49 +02:00
Jagan Teki
bb3362b0ca arm: sunxi: Enable DM_MMC and DM_SCSI
- Enable DM_MMC if MMC defined
- Enable DM_SCSI if SCSI defined

globally through Allwinner platform, the effected SoC families
and boards will make use of MMC and SCSI subsystems in driver-model.

Tested DM_MMC in one board from A64, H6, H5, H3, R40, A83T, A20, A10
SoCs.

Tested-by: Pablo Sebastián Greco <pgreco@centosproject.org> # BPI-M2-Ultra
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-17 14:34:45 +05:30
Tom Rini
015289580f stm32 patches for v2019.07-rc1
- Add trusted boot with TF-A for stm32mp1
 - stm32mp1 dts files sync'ed with Linux version
 - add STM32MP1 Discovery boards (DK1 and DK2)
 - add STMFX gpio expander driver
 - misc improvement for stm3mp1 supports
 - rename stpmu1 to stpmic1 (official name)
 - stm32_qspi: move to exec_op (spi nor driver for stm32 mpu and mcu)
 - add STM32 FMC2 NAND flash controller driver
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJcsLHKAAoJEOKyvdngqpN1iwsH/3HtFxWsIcmT8TfHgIi2USKx
 /Rpj5Mdl0Q0584LAxZXkR2m9YvzBU6n2tR/n9wQfRyiazoEps1LXMmYcZVy35mQg
 AjTNV7xWfC1EZFP0+Gvn5PFquMPoZoIeqbDy1Jk91Qr4CHIqqS64DBwlTmQfjLzf
 6vfoyBcheL5Rf/AGM5AaHMjwh1GZs89cBCeVjGVMUAPgbfFUAKBWwi2fqdgEbDD7
 b9owLl2IykLTHOhvfnZi5NeRoA39deuNB0vSfU4WcMcONhekFCfOPi3Hch5aM/os
 xXlAXkTqps8rVfYHvUUmHm/wJhk+HH69wMThAWNFev/3g94MWR5zen5rjIOBVGg=
 =9M63
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20190412' of https://github.com/patrickdelaunay/u-boot

stm32 patches for v2019.07-rc1
- Add trusted boot with TF-A for stm32mp1
- stm32mp1 dts files sync'ed with Linux version
- add STM32MP1 Discovery boards (DK1 and DK2)
- add STMFX gpio expander driver
- misc improvement for stm3mp1 supports
- rename stpmu1 to stpmic1 (official name)
- stm32_qspi: move to exec_op (spi nor driver for stm32 mpu and mcu)
- add STM32 FMC2 NAND flash controller driver
2019-04-12 15:43:19 -04:00
Patrick Delaunay
c16cc4f689 stm32mp1: add command poweroff
Activate the command poweroff by default for STM32MP1:
- with PCSI from TF-A for trusted boot
- with PMIC sysreset request for basic boot (SYSRESET_POWER)

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12 16:09:13 +02:00
Patrick Delaunay
b4ae34b66b stm32mp1: add runtime information in environment
Set board name with the first dts compatible found in DT
code under CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG

The result with DEVICE_TREE=stm32mp157c-ev1 is:
    STM32MP> env print
    	board=stm32mp1
    	board_name=stm32mp157c-ev1

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12 16:09:13 +02:00
Patrick Delaunay
abf2678f0f stm32mp1: add trusted boot with TF-A
Add support of trusted boot, using TF-A as first stage bootloader,
The boot sequence is
  BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32

The TF-A monitor provides secure monitor with support of SMC
- proprietary to manage secure devices (BSEC for example)
- PSCI for power

The same device tree is used for STMicroelectronics boards with
basic boot and with trusted boot.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12 16:09:13 +02:00
Tom Rini
9c4b0131d1 ti: keystone2: Move CONFIG_ISW_ENTRY_ADDR to a common place
The ISW_ENTRY_ADDR Kconfig option under mach-omap2 isn't a SoC specific
notion but rather "where is our previous stage loaded in memory?"
option.  Make use of this on ARCH_KEYSTONE rather than SPL_TEXT_BASE for
our HS builds that are not using SPL anyhow.

Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com?
2019-04-12 08:05:55 -04:00
Sjoerd Simons
4512380420 am335x, guardian: Add support for the bosch guardian board
Add support for the Bosch Guardian board.

CPU  : AM335X-GP rev 2.1
Model: Bosch AM335x Guardian
I2C:   ready
DRAM:  256 MiB
NAND:  512 MiB
MMC:   OMAP SD/MMC: 0

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Felix Brack <fb@ltec.ch>
2019-04-12 08:05:48 -04:00
Jagan Teki
85c3d46322 arm: sunxi: Enable DM_MMC on required SoCs
Enabling DM_MMC is forcing CONFIG_BLK=y so if any board which uses
SCSI must need to enable DM_SCSI otherwise SCSI reads on that particular
target making invalid reading to the disk drive.

Allwinner platform do support SCSI on A10, A20 and R40 SoC's out of
these only A10 have DM_SCSI enabled. So enabling DM_MMC on A20, R40
would eventually end-up with scsi disk read failures like [1]

So, enable DM_MMC in all places of respective SoC's instead of enabling
them globally to Allwinner platform.

Now, DM_MMC is enabled in Allwinner SoC's except A20 and R40.

[1] https://lists.denx.de/pipermail/u-boot/2019-April/364057.html

Reported-by: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-08 16:35:15 -04:00
Rajesh Bhagat
32413125b3 configs: fsl: move DDR specific defines to Kconfig
Moves below DDR specific defines to Kconfig:

CONFIG_FSL_DDR_BIST
CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE
CONFIG_FSL_DDR_INTERACTIVE
CONFIG_FSL_DDR_SYNC_REFRESH

Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03 20:56:01 +05:30
Peng Ma
f11e492aea armv8: ls1043a: move SCSI_AHCI and SCSI to arm/Kconfig
remove SCSI and SCSI_AHCI configs for ls1043ardb due to no sata interface
support.
this changed is to fixed the ls1043ardb compile warning as fallows:

===================== WARNING ======================
This board does not use CONFIG_DM_SCSI. Please update
the storage controller to use CONFIG_DM_SCSI before the
v2019.07 release. Failure to update by the deadline may
result in board removal.See doc/driver-model/MIGRATION.txt
for more info.
====================================================

Signed-off-by: Peng Ma <peng.ma@nxp.com>
[PK: reword the patch subject]
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19 10:26:44 +05:30
Pankaj Bansal
1eba723c72 lx2160aqds : Add support for LX2160AQDS platform
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.

Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19 10:26:44 +05:30
Priyanka Jain
58c3e62040 armv8: lx2160ardb : Add support for LX2160ARDB platform
LX2160ARDB is an evaluation board that supports LX2160A
family SoCs. This patch add base support for this board.

Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[PK: Sqaush patches from Yinbo Zhu, Peng Ma, Chuanhua Han
and re-arrange defconfig]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19 10:26:43 +05:30
Philippe Reynes
be2fc084d9 bcm963158: add initial support
This add the initial support of the broadcom reference
board bcm963158 with a bcm63158 SoC.

This board has 1 GB of ram, 512 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-02-09 07:50:59 -05:00
Philippe Reynes
ea1a7de532 bcm63158: add initial support
This add the initial support of the broadcom bcm63158 SoC family,
only the cpu, dram and uart are supported.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-02-09 07:50:59 -05:00
Jagan Teki
a7cca57937 arm: sunxi: Enable DM_MMC
Enable DM_MMC for all Allwinner SoCs, this will eventually
enable BLK.

Also removed DM_MMC enablement in few parts of sunxi
configurations.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2019-01-30 18:22:18 +05:30
Tom Rini
d01806a8fc Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2019-01-24 15:30:48 -05:00
Michal Simek
274ccb5b11 arm64: zynqmp: Move SoC sources to mach-zynqmp
Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.

Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.

Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f24036)

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24 10:03:44 +01:00
Michal Simek
088f83ee3a arm64: zynqmp: Setup proper SPI dependency
Select DM_SPI/DM_SPI_FLASH for the whole SoC.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24 10:03:43 +01:00
Michal Simek
6f96fb508d ARM: zynqmp_r5: Setup DM_ETH/MMC if NET/MMC is enabled
Setup proper ETH/MMC dependency for the whole platform.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24 10:03:43 +01:00
Michal Simek
fb69310850 arm64: zynqmp: Setup DM_ETH/MMC if NET/MMC is enabled
Setup proper ETH/MMC dependency for the whole platform.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24 10:03:43 +01:00
Michal Simek
fa7971574c arm64: versal: Setup DM_ETH/MMC if NET/MMC is enabled
Setup proper ETH/MMC dependency for the whole platform.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24 10:03:43 +01:00
Jagan Teki
e236ff0a51 arm: sunxi: Enable CLK, RESET
CLK and DM_RESET drivers are now available for all of
the Allwinner platforms, so enable them in arch/arm/Kconfig

Enabling CLK will select DM_RESET by default.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-18 22:19:09 +05:30
Andre Przywara
3b6989b526 sunxi: drop default SPL_LIBDISK_SUPPORT enablement
There is no code for using partition labels in the Allwinner SPL port.
Even so the name is slightly misleading, CONFIG_SPL_LIBDISK_SUPPORT was
meant to guard partition code for the SPL.

Remove the "imply" line in the Kconfig to make this obvious and avoid
unneeded code inclusions, helping to keep the H6 SPL code small.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2019-01-09 07:13:30 -05:00
Tom Rini
7e40d0a38f Merge branch 'master' of git://git.denx.de/u-boot-samsung 2019-01-06 19:42:55 -05:00
Peng Fan
cd357ad112 imx: rename mx8m,MX8M to imx8m,IMX8M
Rename mx8m,MX8M to imx8m,IMX8M

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jon Nettleton <jon@solid-run.com>
2019-01-01 14:12:18 +01:00
Guillaume GARDET
c96d90367a exynos: imply SYS_THUMB_BUILD
This patch allows smaller binaries.
This is needed for and has been tested on Arndale board, as u-boot.bin is
now bigger than the 512K load limit, with GCC8, without thumb mode.

Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2018-12-26 11:57:48 +09:00
Tom Rini
e7463b37a1 Merge branch 'master' of git://git.denx.de/u-boot-socfpga 2018-12-10 07:15:41 -05:00
Simon Goldschmidt
a9024dc18e arm: socfpga: imply SPL options instead of select
For a small SPL, it should be possible to build without SPI(-flash) drivers
or wihout MMC drivers.

For this to work, we have to change from 'select'ing options to 'imply'ing
them.

With this change, I can have SPL trimmed to my hard-wired starting method
(SPI-NOR or MMC) while still including all drivers in U-Boot.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-12-07 16:32:01 +01:00
Jean-Jacques Hiblot
687ab54560 usb: introduce a separate config option for DM USB device
Using CONFIG_DM_USB for this purpose prevents using DM_USB for host and not
for device.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-12-07 16:31:45 +01:00
Marek Vasut
00e4b57e9e ARM: rmobile: Set environment variable containing CPU type
Set environment variable 'platform' containing the CPU type.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-12-04 09:21:07 +01:00
Tom Rini
0a3d59e010 Xilinx changes for v2019.01
microblaze:
 - Use default functions for memory decoding
 - Showing model from DT
 
 zynq:
 - Fix spi flash DTs
 - Fix zynq_help_text with CONFIG_SYS_LONGHELP
 - Tune cse/mini configurations
 - Enabling cse/mini testing with current targets
 
 zynqmp:
 - Enable gzip SPL support
 - Fix chip detection logic
 - Tune mini configurations
 - DT fixes(spi-flash, models, clocks, etc)
 - Add support for OF_SEPARATE configurations
 - Enabling mini testing with current targets
 - Add mini mtest configuration
 - Some minor config setting
 
 nand:
 - arasan: Add subpage configuration
 
 net:
 - gem: Add 64bit DMA support
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iEYEABECAAYFAlwFUAkACgkQykllyylKDCHtIACeO2G+jfSPxIjsyuPWbRup4e+A
 H5UAn3knKDNJ3VVidqO1C5o8Ye5JePZF
 =lW3g
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2019.01' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2019.01

microblaze:
- Use default functions for memory decoding
- Showing model from DT

zynq:
- Fix spi flash DTs
- Fix zynq_help_text with CONFIG_SYS_LONGHELP
- Tune cse/mini configurations
- Enabling cse/mini testing with current targets

zynqmp:
- Enable gzip SPL support
- Fix chip detection logic
- Tune mini configurations
- DT fixes(spi-flash, models, clocks, etc)
- Add support for OF_SEPARATE configurations
- Enabling mini testing with current targets
- Add mini mtest configuration
- Some minor config setting

nand:
- arasan: Add subpage configuration

net:
- gem: Add 64bit DMA support
2018-12-03 19:30:54 -05:00
Ryder Lee
cbd2fba1ec arm: MediaTek: add basic support for MT7629 boards
This adds a general board file based on MT7629 SoCs from MediaTek.

Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-28 23:04:50 -05:00
Michal Simek
850e7795cd arm64: zynqmp: Enable SPL_SEPARATE_BSS by default
BSS section was all the time separated for SPL but this symbol wasn't
enabled. It is necessary to have it enabled for OF_SEPARATE
configuration where DTB is appended to u-boot with DTB.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-26 10:50:55 +01:00
Philippe Reynes
40b59b0586 bcm6858: add initial support
This add the initial support of the broadcom bcm6858 SoC family,
only the cpu, dram and uart are supported.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2018-11-16 13:34:35 -05:00
Tom Rini
1d6edcbfed - virtio implementation and supporting patches
- DM_FLAG_PRE_RELOC fixes
 - regmap improvements
 - minor buildman and sandbox things
 -----BEGIN PGP SIGNATURE-----
 
 iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlvsxt8RHHNqZ0BjaHJv
 bWl1bS5vcmcACgkQfxc6PpAIrebPtQgAxR8bKdTNODUuVrw5OUIl40ziKQvNIlG5
 uiVsQLDI7Cd9D3Yls8yNffXqkNcQj+0/MJa38UZsm32c/uR4PU0zyFxpz4mwgyXk
 ZMrJ15AEAxf4IOHjbh52sNgR2mw+PeP9A3NO5LnZAMd/rnRF2MgBTy28FvjsBlNn
 z4OUjUpNv4ePND0QQ1EoGPlYotYPASEw8iK1pc5L+Rwq/ponAnNqegKIxQtiMugY
 kLtuFe0JJ704T20UkwYvI8LsnuB50ANRLLMyy5JLy1UtCpS24cc86ml49IKk3pqb
 v4GbnMI67s7S+Imzm4A7Mg8fgGnkkpLqacI3gnlpbIPkLrqRM2C20g==
 =RORj
 -----END PGP SIGNATURE-----

Merge tag 'pull-14nov18' of git://git.denx.de/u-boot-dm

- virtio implementation and supporting patches
- DM_FLAG_PRE_RELOC fixes
- regmap improvements
- minor buildman and sandbox things
2018-11-16 08:37:50 -05:00
Tom Rini
6f44333018 Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2018-11-14 18:25:34 -05:00
Bin Meng
6f3327658b arm: qemu: Add a Kconfig in the board directory
This adds a Kconfig file in the board directory, so that some
board-specific options can be specified there.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-14 09:16:28 -08:00
Marek Vasut
2f13cf35d2 sunxi: Imply fitImage support
Enable modern fitImage format on sunxi.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13 21:56:57 +05:30
Simon Goldschmidt
f48db4ede0 arm: socfpga: imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
Using imply for SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION instead of
select ensures we can build without partition support (used to build
a network boot only version of SPL and U-Boot).

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-10-31 01:41:10 +01:00
Tom Rini
cf033e04da Merged imx8 architecture, fix build for imx8 + warnings
-----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAlvRk0gPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3IuAL/0jfCqEIzKbPXIz81zJ+43ZNPsyu4LluUFsP
 2s5+yKN4zPnxDaHmVyxKynREqCNCcbfz7biStEPRzIjQYPBWUWrqz1yceqvOTqWQ
 eh51ItNeow28IlnVEr40e5cNL28KPsAdO8Tx6yNiXdPndPOgm3DuFlT+Xbnv2/+P
 X9GYBoCD7EQ3aUJBDUKcN/AFSAl8YCQ43FKhowM18/ExeURiKk8YDRXVFgTDDd4J
 HIlzUbyeIG24xfmxc0MsUMEufMjqQE7k/tMfFvQJiwLBLkzuO+1WmbPlWd7XHqco
 t68mheBcm8m2G/CZJoxCy8ymUi5PKDJBhw3qQz646h+JiXP1lg7Yw8hf4nREV56k
 v/bMiDU1exIflI9Qf8CibxRAYv3bjKJD6p/uua2CIvsLO4emLPbi7DHFBdaQq+WB
 r32O0Xc6LiRBIhr/qeL/5HmxFT2o4lo+O9ybo10uhK8RA1LTPlQ0UNMwmSPLl4zR
 7e5YwnRCcHV492+/Fn31LWXUUVVxVw==
 =kkpS
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20181025' of git://git.denx.de/u-boot-imx

Merged imx8 architecture, fix build for imx8 + warnings
2018-10-25 10:16:21 -04:00
Peng Fan
b2b8b9be2f imx: add Kconfig entry for i.MX8QXP
Add Kconfig entry for i.MX8QXP

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2018-10-22 12:59:01 +02:00
Vladimir Zapolskiy
ee54dfea45 arm: lpc32xx: add CONFIG_ARCH_LPC32XX build option
The explicit arch specific build symbol allows to group supported
boards, generalize common config options and it will serve as
a dependency for platform only drivers.

Two related board defconfigs are resynced after the change.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
2018-10-19 12:56:58 -04:00
Michal Simek
22270ca036 arm64: zynqmp: Enable MP by default via Kconfig
Simplify defconfig for ZynqMP but keep option not to enable it for mini
targets.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-10-16 16:53:24 +02:00
Michal Simek
ec48b6c991 arm64: versal: Add support for new Xilinx Versal ACAPs
Xilinx is introducing Versal, an adaptive compute acceleration platform
(ACAP), built on 7nm FinFET process technology. Versal ACAPs combine
Scalar Processing Engines, Adaptable Hardware Engines, and Intelligent
Engines with leading-edge memory and interfacing technologies to deliver
powerful heterogeneous acceleration for any application. The Versal AI
Core series has five devices, offering 128 to 400 AI Engines. The series
includes dual-core Arm Cortex™-A72 application processors, dual-core Arm
Cortex-R5 real-time processors, 256KB of on-chip memory with ECC, more
than 1,900 DSP engines optimized for high-precision floating point with
low latency.

The patch is adding necessary infrastructure in place without enabling
platform which is done in separate patch.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-10-16 16:53:21 +02:00
Tom Rini
bbef20d479 Xilinx changes for v2018.11
- Handle BOARD_LATE_INIT via Kconfig
 
 SPL:
 - Enable GZIP for all partitions types(not only for kernel)
 
 ZynqMP:
 - Rearrange pmufw version handling
 - Support newer PMUFW with improved fpga load sequence
 
 Zynq:
 - Cleanup config file
 - Simplify zybo config by enabling option via Kconfig
 
 net:
 - Fix gems max-speed property reading
 - Enable support for fixed-link phys
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iEYEABECAAYFAluss3IACgkQykllyylKDCFQWwCfc7bvoUN1vevGYTfcG2cEYSF5
 IxQAoI/10FGWJS6rgTG0IVFvoSI1ALhA
 =Q/Tg
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2018.11' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.11

- Handle BOARD_LATE_INIT via Kconfig

SPL:
- Enable GZIP for all partitions types(not only for kernel)

ZynqMP:
- Rearrange pmufw version handling
- Support newer PMUFW with improved fpga load sequence

Zynq:
- Cleanup config file
- Simplify zybo config by enabling option via Kconfig

net:
- Fix gems max-speed property reading
- Enable support for fixed-link phys
2018-09-27 08:29:10 -04:00
Michal Simek
8eb55e1965 arm64: zynqmp: Handle CONFIG_BOARD_LATE_INIT via Kconfig
Disable BOARD_LATE_INIT via Kconfig.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-09-26 10:15:00 +02:00
AKASHI Takahiro
a47c1b5b87 arm: qemu-arm: enable RTC (PL031) by default
Virtual machine provided by qemu-arm has a ARM PL031 Real Time Clock
device. With this patch, the driver is enabled by default.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
2018-09-23 21:55:31 +02:00
Lokesh Vutla
586bde93eb arm: K3: Add initial support for TI's K3 generation of SoCs
Add support for Texas Instruments' K3 Generation Processor
families.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-09-11 08:32:55 -04:00
Vikas Manocha
17d2887a9e arm: stm32: Remove redundant thumb build selection
All armv7m arch builds are thumb & SYS_THUMB_BUILD is already selected by
CPU_ARMV7M.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2018-09-10 21:19:33 -04:00
Masahiro Yamada
c6cca10b9c cmd: ubi: change 'default y' for SUNXI to 'imply' in Kconfig
It is not preferred to put SUNXI-specific code in the common place.

Change it to 'imply' property of ARCH_SUNXI.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-08-26 12:24:03 -04:00
Marek Vasut
d6a61da462 ARM: socfpga: Remove adhoc ethernet reset and configuration
Remove ad-hoc ethernet syscon registers configuration and reset support.
Reset is now handled by the reset framework and the syscon registers are
set in the dwmac_socfpga.c driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-13 22:35:42 +02:00
Baruch Siach
ad105f5f86 mvebu: consolidate SPL boot device config symbols
Use MVEBU_SPL_BOOT_DEVICE_* to select between SPI and MMC, instead of
board specific symbols. This commit enables the boot device selection
menu to all mvebu platforms, but it is only effective on Turris Omnia
and gdsys Controlcenter DC platforms. A following commit will enable
boot selection for other platforms.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-08-06 14:07:23 +02:00
Michal Simek
08a00cba06 dm: Change CMD_DM enabling
CMD_DM is used for debug purpose and it shouldn't be enabled by default
via Kconfig. Unfortunately this is in the tree for quite a long time
that's why solution is to use imply DM for all targets which are
enabling DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-30 07:18:48 -04:00