This function is unused since commit 862274913f ("bus:
uniphier-system-bus: move hardware init from board files").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fill is code for programming the DDR_PHY_CMD_DESKEW_CONx registers,
which are optional, but can be used to fill in the byte lane delays.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement the 'getprisec' subcommand of 'bmode' command for i.MX7 by
reading out the SRC GPR10 bit 30. This bit is either set by the BootROM
if it switched to the secondary copy due to primary copy being corrupted
OR it can be overridden by the user.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add new 'getprisec' subcommand to 'bmode' command, which sets the return
value of the 'bmode' command to either 0 if the system booted from primary
copy or to 1 if the system booted from secondary copy. This can be used
e.g. in 'test' command to determine which copy of the system is running.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The i.MX6/i.MX7 is capable of booting a secondary "redundant" system
image in case the primary one is corrupted. The user can force this
boot mode as well by explicitly setting SRC GPR10 bit 30. This can be
potentially useful when upgrading the bootloader itself. Expose this
functionality to the user.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add the basic differentiation between i.MX6 and i.MX7 into the bmode
command, the mechanism really works almost the same on both platforms.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Make required updates to run on u-boot and strip test code.
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Add support for Xen para-virtualized serial driver. This
driver fully supports serial console for the virtual machine.
Please note that as the driver is initialized late, so no banner
nor memory size is visible.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Port hypervisor related code from Mini-OS. This is referencing the code
of Mini-OS from [1] by Huang Shijie and Volodymyr Babchuk which is for
ARM64.
Update essential arch code to support required bit operations, memory
barriers etc.
Copyright for the bits ported belong to at least the following authors,
please see related files for details:
Copyright (c) 2002-2003, K A Fraser
Copyright (c) 2005, Grzegorz Milos, gm281@cam.ac.uk,Intel Research Cambridge
Copyright (c) 2014, Karim Allah Ahmed <karim.allah.ahmed@gmail.com>
[1] - https://github.com/zyzii/mini-os.git
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
[trini: Drop wmb() from musb-net/linux-compat.h now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce a minimal Xen guest board running as a virtual
machine under Xen Project's hypervisor [1], [2].
Part of the code is ported from Xen mini-os and also uses
work initially done by different authors from NXP: please see
relevant files for their copyrights.
[1] https://xenbits.xen.org
[2] https://wiki.xenproject.org/
Signed-off-by: Andrii Anisov <andrii_anisov@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
The hardcoded platform variables such as DRAM base address are not
common to Aspeed SoCs AST24xx/AST25xx/AST26xx. This patch replaces
those hardcoded with macros defined in a newly added header, where
the basic SoC HW information are assigned accordingly.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Rename the ast2500-board.c to board_common.c and
place the renamed file under the ast2500 folder.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
The original lowlevel_init function of AST2500 is written
in C. However, the C runtime environment is not ready until
_main execution.
This patch adds the assembly version of the lowlevel_init
function. Additional initialization to DRAM configuration
and LPC reset source are also added.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
If an exception occurs, the relocated program counter and return address
are required for an analysis.
With this patch you get:
=> exception undefined
Unhandled exception: Illegal instruction
EPC: 0000000080595908 RA: 000000008059c0c6 TVAL: 000000008030c01e
EPC: 0000000080007908 RA: 000000008000e0c6 reloc adjusted
We can use the relocated addresses to find the involved functions in
u.boot.map:
.text.do_undefined
0x0000000080007908 0x8 cmd/built-in.o
.text.cmd_process
0x000000008000dfcc 0x11a common/built-in.o
0x000000008000dfcc cmd_process
If an exception occurs in an UEFI binary additionally the load addresses of
the UEFI binaries are needed. With this patch:
=> setenv efi_selftest exception
=> bootefi selftest
Unhandled exception: Illegal instruction
EPC: 000000008042e18a RA: 000000008042e18a TVAL: 000000008030c01e
EPC: 000000007fea018a RA: 000000007fea018a reloc adjusted
UEFI image [0x0000000000000000:0xffffffffffffffff] '/\selftest'
UEFI image [0x000000008042e000:0x000000008042e43f] pc=0x18a '/bug.efi'
The value pc=0x18a matches the position of the illegal instruction in
efi_selftest_miniapp_exception.efi (loaded as /bug.efi);
asm volatile (".word 0xffffffff\n");
00000180 93 85 C5 11 1C 64 22 85 82 97 FF FF FF FF 1C 64
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
We should not initialize a variable if the value is overwritten before
being read.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
After
if (ret) return ret;
we know that ret is zero. Don't check it again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
All FU540 driver related options should be in the SoC level Kconfig.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
spl_soc_init() seems to be a better name, as all SPL functions
names start from the spl_ prefix.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
The generic SPL version of board_init_f() should give a call to
board specific codes to initialize board in the SPL phase.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
- Add STM32 FMC2 EBI controller driver
- Fix dwc3-sti-glue which allows STiH410-B2260 to boot again
- Add fitImage its entry for 587-200 DHCOR SoM
- Add both PDK2 and DRC02 DT into DHCOM fitImage its
- Fix DHCOM KS8851 ethernet MAC address
- Remove stm32mp1 board.c file
- Use const for struct node_info in board stm32mp1.c file
-----BEGIN PGP SIGNATURE-----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=J4aq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200813' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Use IS_ENABLED to prevent ifdef in board_key_check for STM32MP
- Add STM32 FMC2 EBI controller driver
- Fix dwc3-sti-glue which allows STiH410-B2260 to boot again
- Add fitImage its entry for 587-200 DHCOR SoM
- Add both PDK2 and DRC02 DT into DHCOM fitImage its
- Fix DHCOM KS8851 ethernet MAC address
- Remove stm32mp1 board.c file
- Use const for struct node_info in board stm32mp1.c file
Fix these dtc warnings:
Warning (reg_format)
Warning (avoid_default_addr_size)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
The STM32MP1 DHCOM has two ethernet interfaces, the on-SoM DWMAC and KS8851.
Set eth1addr for the KS8851 to a MAC address of the DWMAC incremented by 1.
The MAC of the DWMAC is set from on-SoM EEPROM already, but the MAC address
of KS8851 was left uninitialized, so fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch adds FMC2 External Bus Interface support on stm32mp157c.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in stm32prog command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in bsec driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add the basic a72 basic dts for j7200. Following nodes were supported:
- UART
- MMC SD
- I2C
- TISCI communication
- LPDDR with 1600MTs configuration.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Detect if sysfw is already loaded by ROM and pass this information to
sysfw loader. Based on this information sysfw loader either loads the
sysfw image from boot media or just receives the boot notification
message form sysfw.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Starting J7200 SoC, ROM supports for loading sysfw directly from boot
image. ROM passes this information on number of images that are loaded
to bootloader at certain location. Add support for storing this
information before it gets corrupted.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
The J7200 SoC is a part of the K3 Multicore SoC architecture platform.
It is targeted for automotive gateway, vehicle compute systems,
Vehicle-to-Vehicle (V2V) and Vehicle-to-Everything (V2X) applications.
The SoC aims to meet the complex processing needs of modern embedded
products.
Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, two clusters of lockstep
capable dual Cortex-R5F MCUs and a Centralized Device Management and
Security Controller (DMSC).
* Configurable L3 Cache and IO-coherent architecture with high data
throughput capable distributed DMA architecture under NAVSS.
* Integrated Ethernet switch supporting up to a total of 4 external ports
in addition to legacy Ethernet switch of up to 2 ports.
* Upto 1 PCIe-GEN3 controller, 1 USB3.0 Dual-role device subsystems,
20 MCANs, 3 McASP, eMMC and SD, OSPI/HyperBus memory controller, I3C and
I2C, eCAP/eQEP, eHRPWM among other peripherals.
* One hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
management.
See J7200 Technical Reference Manual (SPRUIU1, June 2020)
for further details: https://www.ti.com/lit/pdf/spruiu1
Add support for detection J7200 SoC
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
In main control mmr there is no partition 4 and partition 6 is available
only on J721e. Fix the same in ctrl_mmr_unlock function
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Add an api soc_is_j721e(), and use it to enable certain functionality
that is available only on j721e. This detection is needed when DT is not
available.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Starting J7200 SoC, ROM supports for loading sysfw directly from boot
image. In such cases, SPL need not load sysfw from boot media, but need
to receive boot notification message from sysfw. So separate out
remoteproc calls for system controller from sysfw loader and just
receive the boot notification if sysfw is already loaded.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
mmr_unlock api is common for all k3 devices. Move it to a common
location.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
If SPL_MULTI_DTB_FIT is not enabled, then CONFIG_SPL_OF_LIST is not defined
And in turn tispl.bin ends up not embedding any DTB.
Fixing it by using CONFIG_DEFAULT_DEVICE_TREE if SPL_OF_LIST is empty.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Guard all eeprom probe with TI_I2C_BOARD_DETECT to avoid reading eeprom
when eeprom is not available
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
U-boot only supports either USB host or device mode for a node at a
time in dts. To support both host and dfu bootmodes, set "peripheral"
as the default dr_mode but fixup property to "host" if host bootmode
is detected.
This needs to happen before the dwc3 generic layer binds the usb device
to a host or device driver. Therefore, add an fdtdec_setup_board()
implementation to fixup the dt based on the boot mode.
Also use the same fixup function to set the USB-PCIe Serdes mux to PCIe
in both the host and device cases. This is required for accessing the
interface at USB 2.0 speeds.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
In order to be able to use things like file system drivers early on in
SPL (before relocation) in a memory-constrained environment when DDR is
not yet available we cannot use the simple malloc scheme which does not
implement the freeing of previously allocated memory blocks. To address
this issue go ahead and enable the use of the full malloc by manually
initializing the required functionality inside board_init_f by creating
a full malloc pool inside the pre-relocation malloc pool.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The various CBASS interconnect nodes on K3 J721E SoCs are defined
using the node name "interconnect". This is not a valid node name
as per the dt-schema. Fix these node names to use the standard name
used for SoC interconnects, "bus".
Signed-off-by: Suman Anna <s-anna@ti.com>
The various CBASS interconnect nodes on K3 AM65x SoCs are defined
using the node name "interconnect". This is not a valid node name
as per the dt-schema. Fix these node names to use the standard name
used for SoC interconnects, "bus".
Signed-off-by: Suman Anna <s-anna@ti.com>
This commit completes the migrations for DM_ETH and DM_USB. The board
is now consistent with omap3_beagle and other remaining OMAP3 boards.
Cc: Tom Rini <trini@konsulko.com>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
When switching on or off the ARM caches some care must be taken to ensure
existing cache line allocations are not left in an inconsistent state.
An example of this is when cache lines are considered non-shared by
and L3 controller even though the lines are shared. To prevent these
and other issues all cache lines should be cleared before enabling
or disabling a coherent master's cache. ARM cores and many L3 controllers
provide a way to efficiently clean out all cache lines to allow for
this, unfortunately there is no such easy way to do this on current K3
MSMC based systems.
We could explicitly clean out every valid external address tracked by
MSMC (all of DRAM), or we could attempt to identify only the set of
addresses accessed by a given boot stage and flush only those
specifically. This patch attempts the latter. We start with cleaning the
SPL load address. More addresses can be added here later as they are
identified.
Note that we perform a flush operation for both the flush and invalidate
operations, this is not a typo. We do this to avoid the situation that
some ARM cores will promote an invalidate to a clean+invalidate, but only
emit the invalidation operation externally, leading to a loss of data.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Add DT entries for main domain watchdog0 and 1 instances on the J721e
well as RTI1-based watchdog on the AM65x. RTI0 does not work for this
purpose on the AM65x, so leave it out.
On AM65x, we mark the power-domain as shared because RTI firmware such
as https://github.com/siemens/k3-rti-wdt may request it as well in order
to prevent accidental shutdown of the watchdog.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Add LED support for Cortina Access Presidio Engineering Board
Signed-off-by: Jway Lin <jway.lin@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CC: Simon Glass <sjg@chromium.org>
Factor out ppc-specific bdinfo setup from generic init sequence to
arch_setup_bdinfo in arch/powerpc/lib/bdinfo.c.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Factor out m68k-specific bdinfo setup to arch_setup_bdinfo in
arch/m68k/lib/bdinfo.c. Also, use if(IS_ENABLED()) instead of #ifdef where
possible.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Move all assignments to gd->bd->bi_mem{start,size} to generic code in
setup_bdinfo.
Xtensa architecture is special in this regard as it defines its own
handling of gd->bd->bi_mem{start,size} fields. In order to avoid defining
a weak SDRAM function, let arch_setup_bdinfo overwrite the generic flags.
For ARC architecture, remove ARCH_EARLY_INIT_R from Kconfig since it is
not needed anymore.
Also, use gd->ram_base to populate bi_memstart to avoid an ifdef.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Acked-by: Alexey Brodkin <abrokdin@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
bi_sramstart and bi_sramsize are generic members of the bd_info structure,
so move the m68k/powerpc-specific prints to generic code. Also, print them
only if SRAM support is enabled via CONFIG_SYS_HAS_SRAM.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Update the MikroTik CRS305-1G-4S flash layout to support redundant UBI
partitions.
Additionally enable the UBI commands in crs305-1g-4s_defconfig.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS328-4C-20S-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS326-24G-2S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS305-1G-4S Bit board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
The Bit board variant is added, which has a bigger Macronix flash.
Add basic U-Boot, UART and Winbond SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
We still have some platforms that only implements functionalities in
PSCI 0.1 (e.g. Allwinner ARMv7 SoCs).
Add a Kconfig option for exporting only PSCI 0.1. The code to export
PSCI 0.1 is still available and gets activated by this patch.
In addition, default ARCH_SUNXI U-Boot PSCI implementation to export
PSCI 0.1, to fix poweroff/reboot regression on Allwinner multi-core
ARMv7 SoCs.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
SPL_CLEAR_BSS is called regardless of build type if
CONFIG_SPL_EARLY_BSS is defined. Add a guard for CONFIG_SPL_BUILD
to fix.
Signed-off-by: Brian Moyer <bdm310@gmail.com>
This patch adds a feature for block device cloning similar to dd
command, this should be useful for boot-strapping a device where
usb gadget or networking is not available. For instance one can
clone a factory image into a blank emmc from an external sd card.
Signed-off-by: John Chau <john@harmon.hk>
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXykjtQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76a1WQCcD+objdS+90mDdT0yTpW3jHS4YiwAn2V2rTTo
4hKj5yxRg3cvb/pBAmbQ
=TyRs
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200804' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2020.10
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
This header file should not be included in other header files. Remove it
from each one and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
PRCI module within SiFive SoC's has register with which we can
reset the sub-systems within the SoC. The resets to DDR and ethernet
sub systems within FU540-C000 SoC are active low, and are hold low
by default on power-up. Currently these are directly asserted within
prci driver via register read/write.
With the DM based reset driver support here, we bind the reset
driver with clock (prci) driver and assert the reset signals of
both sub-system's appropriately.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Pragnesh Patel <Pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
The resets to DDR and ethernet sub-system are connected to
PRCI device reset control register, these reset signals
are active low and are held low at power-up. Add these reset
producer and consumer details needed by the reset driver.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
This patch selects DM_SPI & DM_I2C for MIPS Octeon. DM_GPIO, DM_SERIAL
and DM_ETH are already selected.
Additionally the selections are now alphabetically sorted.
Signed-off-by: Stefan Roese <sr@denx.de>
Instead of hang()ing the system and thus disallowing any automated
recovery possibility from a HAB authentication failure, panic() .
The panic() function can be configured to hang() the system after
printing an error message, however the default is to reset the
system instead.
This allows redundant boot to work correctly. In case the primary
or secondary image cannot be authenticated, the system reboots and
bootrom can try to start the other one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
MYS-6ULX is single board computer (SBC) comes with eMMC or NAND based
on imx6ULL SoC from NXP and provision for expansion board. This
commit adds support only for SBC with NAND.
CPU: Freescale i.MX6ULL rev1.1 528 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 45C
Reset cause: WDOG
Model: MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND
Board: MYiR MYS-6ULX 6ULL Single Board Computer
DRAM: 256 MiB
NAND: 256 MiB
MMC: FSL_SDHC: 0
In: serial@2020000
Out: serial@2020000
Err: serial@2020000
Net: FEC0
Working:
- Eth0
- MMC/SD
- NAND
- UART 1
- USB host
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
- ApolloLake: add u64 parameters support for FSP2 bindings
- ApolloLake: add missing parameters to support full configuration of
the latest FSP MR6 release
- Append appropriate suffixes in various assembly codes
Assembler is not happy:
arch/x86/cpu/call32.S: Assembler messages:
arch/x86/cpu/call32.S:36: Warning: no instruction mnemonic suffix given and no register operands; using default for `retf'
Fix this by adding appropriate suffixes to the assembler commands.
Fixes: 6f92ed8f1a ("x86: Add a way to call 32-bit code from 64-bit mode")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Assembler is not happy:
arch/x86/cpu/sipi_vector.S: Assembler messages:
arch/x86/cpu/sipi_vector.S:134: Warning: no instruction mnemonic suffix given and no register operands; using default for `cmp'
arch/x86/cpu/sipi_vector.S:139: Warning: no instruction mnemonic suffix given and no register operands; using default for `bts'
arch/x86/cpu/sipi_vector.S:157: Warning: no instruction mnemonic suffix given and no register operands; using default for `cmp'
Fix this by adding appropriate suffixes to the assembler commands.
Fixes: 45b5a37836 ("x86: Add multi-processor init")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add missing parameters to support full configuration of the latest FSP
MR6 release.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add FSP_UINT64 read support as preparation for FSP-M and FSP-S parameter
update.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix some typos in arch/x86/include/asm/irq.h.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add simple DT and clock bindings to r2dplus DT to permit U-Boot
to bind the SCIF driver via DT probing instead of hard-coded
config options.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The gd->malloc_base must be set before the C runtime if the MALLOC_F_LEN
is non-zero, otherwise we hit assertion in dlmalloc.c initf_malloc(). So
set it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The Kconfig symbol CONFIG_STACK_SIZE is used both by ARM and Microblaze
with the same meaning. Move it to menu 'General setup' so that we can use
it for all architectures.
Use the value of CONFIG_STACK_SIZE instead of a hard coded 16 MiB value for
reserving memory in the UEFI sub-system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Configuration variables should have the same meaning independent of the
architecture. x86 and ARM both use CONFIG_STACK_SIZE:
* x86: U-Boot's runtime stack size during reboot
* ARM: max stack size that can be used by U-Boot
Rename the x86 configuration variable to CONFIG_STACK_SIZE_REBOOT
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Refactor to allow any arch to create SPI-flash images
New button uclass
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8g33sRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaeEgf/QhmJjd6lEE3ABncRa3texyqq7j9eu+9P
2JMCahrIzps83LLOkzNSGs1+m1hRuTcdnYNV8FxdmkAjDTYwV5RHOfwtpAr2nkH2
HBbJRA2qMPleqT8wcymouhaCIRTTCGfUkFgZ+OowwSlHnQ4d2oGU/59Z+AkbpfX0
3svA1Mlr5rUTZ3qTvdsepuZckuYOTGYZ5jgjbgr+G8F4iW4Ov+OkBxqDz9zFCveF
md5CHKP1SV+bq67Q9uqUEwatLzYpy1p24j1Qe4G08U1+XCi6r+95VEc7TWxggboj
eV/5d/sZbGESAtJiJ4TmqpGVcOLzBLI0FOunky0JNFwdcyRS/6KcCg==
=Xjil
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-28jul20' of git://git.denx.de/u-boot-dm
Use binman instead of one of the Rockchip build scripts
Refactor to allow any arch to create SPI-flash images
New button uclass
- fix SPL boot issue due to early dbgmcu_init() call
- fix SPL boot issue due to dcache memory region configuration
- add support of CONFIG_ENV_IS_IN_MMC
- add specific SD/eMMC partition for U-Boot enviromnent
- enable env in SPL
- use "env info -q" to remove log during boot
- remove env location override for dh_stm32mp1
- update management of misc_read
- check result of find_mmc_device in stm32prog
- use regulator_set_enable_if_allowed for disabling vdd supply in usbphyc
- enable CMD_ADTIMG flag to handle Android images
- device tree alignment with Linux Kernel v5.8-rc1
- remove hnp-srp-disable for usbotg on dk1
- add reset support to uart nodes on stm32mp15x
- use correct weak function name spl_board_prepare_for_linux
- use cd-gpios for ST and DHSOM boards
- add seeed studio odyssey-stm32mp157c board support
- move ethernet PHY into SoM DT
- add DHSOM based DRC02 board support
Use device tree and UCLASS_SYSCON driver to get
Generic Interrupt Controller (GIC) lpi address and
maximum GIC redistributors count.
Also update Kconfig to select REGMAP and SYSCON when
GIC_V3_ITS is enabled.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use device tree and UCLASS_IRQ driver to get following
Generic Interrupt Controller (GIC) details,
-GIC Distributor interface (GICD) base address and
-GIC Redistributors (GICR) base address.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch bcmns3.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add both DRAM banks memory information and
the corresponding MMU page table mappings.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add API to save boot parameters passed from BL31
Use assembly implementation of save_boot_params instead of c function.
Because generally ATF does not set up SP_EL2 on exiting.
Thus, usage of a C function immediately after exiting with no stack
setup done by ATF explicitly, may cause SP_EL2 to be not sane,
which in turn causes a crash if this boot was not lucky to get
an SP_EL2 in valid range. Replace C implementation with assembly one
which does not use stack this early, and let u-boot to set up its stack
later.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Signed-off-by: Rajesh Ravi <rajesh.ravi@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Broadcom Northstar 3 SoC.
NS3 is a octo-core 64-bit ARMv8 Cortex-A72 processors
targeting a broad range of networking applications.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- SPL not supported yet --> no spl-dir in arch/arm/cpu/armv7/s5p4418/.
Appropriate line in Makefile removed.
- cpu.c: '#include <cpu_func.h>' added.
- arch/arm/cpu/armv7/s5p4418/u-boot.lds removed, is not required
anylonger.
- "obj-$(CONFIG_ARCH_NEXELL) += s5p-common/" added to
arch/arm/cpu/armv7/Makefile since s5p-common/pwm.c is used instead
of drivers/pwm/pwm-nexell.c.
- s5p4418.dtsi: '#include "../../../include/generated/autoconf.h"'
removed, is not necessary, error at out-of-tree building.
'#ifdef CONFIG_CPU_NXP4330'-blocks (2x) removed. Some minor changes
regarding mmc. 'u-boot,dm-pre-reloc' added to dp0 because of added
DM_VIDEO support.
- board/s5p4418/ renamed to board/friendlyarm/
- All s5p4418-boards except nanopi2 removed because there is no
possibility to test the other boards.
- Kconfig: Changes to have a structure like mach-bcm283x (RaspberryPi),
e.g. "config ..." entries moved from/to other Kconfig.
- "CONFIG_" removed from several s5p4418/nanopi2 specific defines
because the appropriate values do not need to be configurable.
- nanopi2/board.c: All getenv(), getenv_ulong(), setenv() and saveenv()
renamed to env_get(), env_get_ulong(), env_set() and env_save(),
respectively. MACH_TYPE_S5P4418 is not defined anymore, therefore
appropriate code removed (not necessary for DT-kernels).
- nanopi2/onewire.c: All crc8() renamed to crc8_ow() because crc8() is
already defined in lib/crc8.c (with different parameters).
- dts: "nexell,s5pxx18-i2c" used instead of "i2c-gpio", i2c0 and
i2c1 added. gmac-, ehci- and dwc2otg-entries removed because the
appropriate functionality is not supported yet. New mmc-property
"mmcboost" added.
s5p4418-pinctrl.dtsi: gmac-entries removed, mmc- and i2c-entries
added.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
possible (and similar).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- Since drivers/pwm/pwm-nexell.c is an adapted version of
s5p-common/pwm.c an appropriately changed version of s5p-common/pwm.c
is used instead. Therefore arch/arm/mach-s5pc1xx/include/mach/pwm.h
copied to arch/arm/mach-nexell/include/mach and s5p-common/Makefile
changed appropriately.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
possible (and similar).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- SPL not supported yet --> no spl-directory in arch/arm/mach-nexell.
Appropriate line in Makefile removed.
- clock.c: 'section(".data")' added to declaration of clk_periphs[] and
core_hz.
- Kconfig: Changes to have a structure like in mach-bcm283x/Kconfig,
e.g. "config ..." entries moved from other Kconfig.
- timer.c: 'section(".data")' added to declaration of timestamp and
lastdec.
- arch/arm/mach-nexell/serial.c removed because this is for the UARTs
of the S5P6818 SoC which is not supported yet. S5P4418 UARTs are
different, here the (existing) PL011-code is used.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
possible (and similar).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
The LPAE versions of DCACHE_WRITEBACK and DCACHE_WRITETHROUGH are currently
defined as no-allocate for both reads and writes, which deviates from the
non-LPAE definition, and mostly defeats the purpose of enabling the caches
in the first place.
So align LPAE with !LPAE, and enable allocate-on-read for both. And while
at it, add some clarification about the meaning of the chosen values.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
This introduces initial support for the popular Qualcomm
IPQ40x8 and IPQ40x9 WiSoC series.
IPQ40xx series have 4x Cortex A7 ARM-v7A cores.
Supported are: IPQ4018, IPQ4019, IPQ4028 and IPQ4029.
IPQ40x8 and IPQ40x9 use the same cores, but differ in
addressable RAM size (1GB for IPQ40x9 and 256MB for IPQ40x8)
and supported peripherals (IPQ40x8 lacks RGMII, LCD controller
and EMMC/SDHCI controllers).
IQP4028/IPQ4029 models differ from IPQ4018/IPQ4019 only
by their rated temperatures rates with IPQ402X models being
rated for wider temperature ranges.
Initially this supports:
* Simple clock driver (Only for UART1 now, will be extended)
* Pinctrl driver (Supports UARTX and GPIO now, will be extended)
* GPIOs already supported by msm_gpio driver with updates
* UARTs already supported by serial_msm driver with updates
Further peripherals will come in later patches.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Adds two buttons on sandbox so button framework may be tested.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Since commit 9ba84329dc ("sandbox, test: add test for GPIO_HOG
function"), the gpio_a 0,1,2 and 3 are used by hog in test.dts.
But 2 leds 'sandbox:red' and 'sandbox:green' are using gpio_a 0
and 1. As hog always request his gpios, the led command on both
led is broken:
=> led sandbox:red
LED 'sandbox:red' not found (err=-16)
The gpio is already requested by hog, so it can't be enabled
for led 'sandbox:red'.
This commit change the gpio used by hog to 10, 11, 12 and 13,
so the led command could be used again with 'sandbox:red' and
'sandbox:green'.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
This board does not have microcode but at present that is not supported
by Kconfig nor the binman image layout. Fix both of these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This causes conflicts on chromebook_link64. Move it to after U-Boot where
there should be plenty of space.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that all board use binman instead of this script, drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this board uses a custom script to produce the .its file.
Update it to use binman instead. Binman can create all the images that
are needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
On mediatek various files that need to be created by binman. It does not
make sense to enumerate these in the Makefile. They are described in the
configuration (devicetree) for each board and we can simply run binman
(always) to generate them.
This avoid sprinkling the Makefile with arch-specific code.
Also update the binman definition so that idbloader.img is only needed
when SPL is actually being used.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Quite a few boards using this SoC family don't use binman, yet
CONFIG_BINMAN is enabled for all of them. But the option should only be
enabled if we expect binman to produce an image. Calling binman when the
device tree is missing, etc. will cause failer.
Add a condition so that CONFIG_BINMAN is only enabled as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When binman is in use, most of the targets built by the Makefile are
inputs to binman. We then need a final rule to run binman to produce the
final outputs.
Rename the variable to indicate this, and add a new 'inputs' target.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present only the ARMv7 tegra SoCs actually use binman to create an
image. Change the config to reflect this, since otherwise running binman
will produce an error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple binman config and enable CONFIG_HAS_ROM so that U-Boot
produces a ROM for jerry.
Change the binman image definition to support multiple images, since it
may be used to build both u-boot-rockchip.bin and u-boot.rom
Signed-off-by: Simon Glass <sjg@chromium.org>
Most x86 boards build a u-boot.rom which is programmed into SPI flash. But
this is not unique to x86. For example some rockchip boards can also boot
from SPI flash.
Also, at least on x86, binary blobs are sadly quite common. It is not
possible to build a functional image without them, and U-Boot needs to
know this at build time.
Introduce a new CONFIG_HAS_ROM option which selects whether u-boot.rom is
built and a new CONFIG_ROM_NEEDS_BLOBS option to indicate whether binary
blobs are also needed. If they are not needed, it is safe to build the ROM
always. Otherwise we still require the BUILD_ROM environment variable.
For now this affects only x86, but future patches will enable this for
rockchip too.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add DT for DH DRC02 unit, which is a universal controller device.
The system has two ethernet ports, two CANs, RS485 and RS232, USB,
capacitive buttons and an OLED display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The PHY and the VIO regulator is populated on the SoM, move it
into the SoM DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This commit adds device tree files supporting
SBC from Seeed Studio based on STM32MP157C.
This works with generic stm32mp1 config.
Right now only booting from SD card is supported.
Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Since commit f13ff88b61 ("gpio: stm32: add ops set_dir_flags")
the gpio flags are supported by stm32 pinctrl driver.
The cd-gpios is correctly handle in U-Boot and the patch on the
device tree can be removed.
This reverts commit 792919241b.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Since commit f13ff88b61 ("gpio: stm32: add ops set_dir_flags")
the gpio flags are supported by stm32 pinctrl driver.
The cd-gpios is correctly handle in U-Boot and the patch on the
device tree can be removed.
This reverts commit 3c2e2a1a79.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Replace the function spl_board_prepare_for_boot_linux by the correct
name of the weak function spl_board_prepare_for_linux defined in spl.h.
This patch avoids warning with W=1 option:
u-boot/arch/arm/mach-stm32mp/spl.c:150:6:
warning: no previous prototype for ‘spl_board_prepare_for_boot_linux’
[-Wmissing-prototypes]
Fixes: dc7e5f190d ("arm: stm32mp: activate data cache on DDR in SPL")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
STM32 serial IP can be reset via reset controller.
Add the support of reset to uart nodes on stm32mp15-u-boot.dtsi,
the ad-dons file for U-Boot.
This patch fix issues when previous UART configuration, for example
done in TF-A or ROM code, is not handled in U-Boot stm32 serial driver
init.
This reset property won't be not added in Linux kernel device tree
as this reset is not used in Linux STM32 serial driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove hnp-srp-disable for usbotg node because this feature is only needed
for usbotg in HOST mode (in drivers/usb/host/dwc2.c)
and this feature is not activated in stm32mp15 U-Boot
(stm32mp15_basic_defconfig and stm32mp15_trusted_defconfig);
only the device mode is activated and OTG is not supported in DWC2 driver.
This patch reduces the difference between U-Boot and Linux kernel
device-tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
DT alignment with Linux kernel v5.8-rc1 for the STM32MP15x soc
device tree files and the STMicroelectronics boards device tree files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Alignment with pins name used in Linux kernel v5.8.
It is a preleminary step for device tree alignment.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Check result of find_mmc_device() before calling mmc_init().
This patch avoid a data abort when the command try to acces
to sd/mmc device deactivated in device tree.
Fixes: aff4c5dd82 ("stm32mp: stm32prog: add MMC device")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Save the environment at the end of the U-Boot partition, the GPT
partition named "ssbl" in SD card or eMMC and avoid requirements
on the "bootfs" file system generated via specific raw tools
(like wic and genimage).
With the previous configuration of the U-Boot environment saved in ext4
file, U-Boot need to create/modify the file uenv.txt in the ext4 file
system; so this EXT4 file system need to be generated without some
functionality, like metadata_csum and dir_index, because they are not
supported by U-Boot.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Since commit d877f8fd0f ("arm: provide a function for boards init
code to modify MMU virtual-physical map") the parameter of
mmu_set_region_dcache_behaviour need to be MMU_SECTION_SIZE
aligned.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
As the dbgmcu_init use the function bsec_dbgswenable which is based
on the DM and DT, its call can't be done before the spl is initialized
(driver model, DT and malloc) in board_init_f::spl_early_init().
This function call is moved later in spl_board_init().
Fixes: bd3f60d29c ("arm: stm32mp: protect DBGMCU_IDC access with BSEC")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
Checkpatch reports the following issue:
ERROR: space prohibited before that ',' (ctx:WxW)
#936: FILE: arch/arm/mach-imx/imx8m/soc.c:936:
+ 0, 0 , 0, 0, 0, 0, &res);
Remove the unneeded space.
^
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
