When moving the PHYLIB PHY drivers around in Kconfig we did not at the
same time perform a careful migration of the related drivers and
sub-options. This lead to the case where previously Kconfig-enabled
driver choices were now disabled on some platforms. Correct this by
enabling both the PHY driver and sub-option on the above referenced
platforms.
Fixes: af2cbfd6b9 ("drivers: net: Provide Kconfig menu for PHYLIB")
Fixes: 8728c97eff ("configs: Re-sync")
Reported-by: Dario <dario86@tutamail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
After checking back on the original commit I can see that these are the
only two platforms to have been broken in the change.
Enable these standard U-Boot commands for image manipulation and for
starting the default boot command using 'boot' command in U-Boot shell.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
FVP now loads an Android boot image named boot.img if available,
otherwise it falls back to the existing code path.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
FU540 uses OF_SEPARATE instead of OF_PRIOR_STAGE.
Enable OF_BOARD_FIXUP to update the DT with reserved-memory node.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
With support added for Armada 38x, include the bubt command in
ClearFog defconfig.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Update mvebu SPL boot selection mechanism for the move to driver model
usage by ensuring that the required driver support for SPI and MMC
booting is available in SPL when the respective boot method is
selected.
Previously, all mvebu boards selected a boot method (implicitly
MVEBU_SPL_BOOT_DEVICE_SPI for many) even if SPL booting wasn't used.
This changes mvebu boot method selection to depend on SPL usage which
resolves the issue with aarch64 boards which don't use SPL getting an
implicit boot device selection resulting in unmet dependencies. The
32-bit arm boards do use SPL, but I'm led to conclude that most aren't
intentionally using the MVEBU_SPL_BOOT_DEVICE selection since none have
SPL_DM_SPI enabled in their defconfig even though they still implicitly
select the SPI boot method.
This also results in the new addition of SPL_GPIO_SUPPORT to helios4.
The mainline dts for helios4 includes the cd-gpios entry for sdhci with
identical addresses as the clearfog dts. I don't have a helios4 board
to confirm, but based on the current source conclude that the board
itself is either wired to pull the signal low for eMMC, or the default
MMC boot isn't fully functional in mainline. In either case, as far as
I can tell, including the GPIO support will at least cause no
regression.
Tested on SolidRun ClearFog devices.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
-----BEGIN PGP SIGNATURE-----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=1Ffl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200420' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- enable DM_RNG on meson boards
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
- Fix boot on am335x guardian board
- Increase OPSI speed on AM65x and J721E devices
- Use JTAD register for identifying K3 devices.
- Update TI entry in MAINTAINERS file.
The CONFIG_PHY_FIXED is necessary to allow DSA switch work in U-Boot after
the
commit 3bf135b6c3 ("drivers: net: phy: Ignore PHY ID 0 during PHY probing").
This particular device - LAN9303 - returns phy_id == 0. With
CONFIG_PHY_FIXED enabled HSC and DDC boards work again with the same U-Boot
binary.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Use DM_ETH instead of legacy networking. Add VIO as a fixed regulator
to the relevant device-trees and augment the FEC node with properties
for the reset GPIO.
It should be noted that the relevant properties for the reset GPIO
already exist in the PHY node (reset-gpios, reset-delay-us,
reset-post-delay-us) but U-Boot currently ignores those and only
supports the bus-level reset properties in the FEC node
(phy-reset-gpios, phy-reset-duration, phy-reset-post-delay).
Signed-off-by: Harald Seiler <hws@denx.de>
Since we are using revD1 device tree for all board revisions, the
following can be seen on a revB1 board:
Model: Wandboard i.MX6 Quad Board revD1
Board: Wandboard rev B1
To avoid such confusing messages, disable CONFIG_DISPLAY_BOARDINFO_LATE.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
The detection of the revD1 version is based on the presence of the PMIC.
Currently revb1 device trees are used for mx6q/mx6dl variants, which
do not have the PMIC nodes.
This causes revD1 boards to be incorrectly be detected as revB1.
Fix this issue by using the revd1 device trees, so that the PMIC node can be
found and then the PMIC can be detected by reading its register ID.
Imported the revd1 device trees from mainline kernel version 5.7-rc1.
Reported-by: Heiko Schocher <hs@denx.de>
Reported-by: Derek Atkins <derek@ihtfp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Derek Atkins <derek@ihtfp.com>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
mxsfb needs a dcache function not implemented in cortex-M7, so for the
moment let's keep dcache not enabled.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Enable DM_VIDEO subsystem and its BACKLIGHT_GPIO. Then enable
SYS_WHITE_ON_BLACK to have classic black background on display. Need
also to enable CONFIG_SYS_CONSOLE_ENV_OVERWRITE to retrieve
stdin/stdout/stderr from CONFIG_EXTRA_ENV_SETTINGS.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Currently the following build warning is seen:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
===================================================
Since the mx6ulz-evk board does not have networking support, explicitly
disable networking to avoid the board removal.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
CONFIG_FEC_MXC is supported in Kconfig, so it is preferred to
move it to defconfig file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This is pretty minor set of changes mostly touching HSDK board:
* Enable on-chip reset controller on HSDK
* Add possibility to turn-on & off L2$ on more
recent ARC HS processors.
* AXI tunnel clock calculation on HSDK
This pull request
* provides an implementation of UEFI secure booting
* fixes a problem with the rsa_mod_exp driver which stops some boards
from booting when CONFIG_RSA is enabled which is needed for UEFI
secure booting
* enables the EFI_RNG_PROTOCOL if DM_RNG is enabled
* fixes some function comments
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAl6YjlcACgkQxIHbvCwF
GsQ6Jg/+KVRQF0Dn2jiag8Me9ZhafZx4xGTI3LEzFD7V9kG3dmUzbO3m8a5dEevW
bcPNA6EmcKAjyP09AZY4C8ns4sU7wzPu/GQvApD4S5+vcuNbEqRHfW6zzReNXq09
t89DrFH+XLhGnh4uSh0hmfjrlIPVi86hs/f57vKRayrBu8W2yGPci3SNTO5Y0AY1
to7sxP3hGlDCUhqIABWp5ylpWWUSG1MsVNcMOnHpj+jl0iWWYP46EQrGr95egQor
gcGgUOLdOLLOHPYUIOBmo9INnS2MbvE9Mfgh5Bw7JW8DIu/Xp7r1qePQyMLsngc1
pO5yzwMq6EQy6OjuYnXdIBXtHOlZ8rnE9pbTgyUR8T/2CdL2hqr9ddpqa4ryDABX
iaQF8FG+KhY0XQ5EIJV7pEkvf9TMwGguJNlOkmJPeub2n9i0k1tPk0Rwq5ZWWBIn
rHcgZXwl0On3O3f0HvfL0Oas5u9KE1HhA12h/EVmu2Muy36x2WxAAzDnsH19HzqU
QnWBAo8VMyp3qTIZjb3y+qrxcU/joPGt9+hxmur03hzmKOJ9JNOv6vExb+yUIyXQ
4ML6jvTvSVZbvkP++0zMKOjT8ks3xv5q84oFD5Gp4cG8ZpHpA9dj3mXM92Waepo4
pAkko5IGQ4SqaGIBltEQzrG+cCiHHezdD/raCwAo6DgYSmfZUvc=
=+ZDZ
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc1
This pull request
* provides an implementation of UEFI secure booting
* fixes a problem with the rsa_mod_exp driver which stops some boards
from booting when CONFIG_RSA is enabled which is needed for UEFI
secure booting
* enables the EFI_RNG_PROTOCOL if DM_RNG is enabled
* fixes some function comments
As the driver of on-chip reset controller became available
we are ready to enable it.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Enhancements to 'dm' command
Log test enhancements and syslog driver
DM change to read parent ofdata before children
Minor fixes
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl6YdaMRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYLRwf8C+vKmERVLLcrMZMMiLctbY2kVflJV8zG
RjFwBcazZDPYjtHqClFZtJyIDYzgkVQRo+QPcdLxjcA+gjSXdteeRa0XTsBTXOZQ
kbs7yBkL+rCIO2WyXtuyajsmDMQtqM5vYgeBdTeYnJu7NVxwRMYrUqqAKLolNpIN
SKNYz+a8OEOG2EetbTdwwrmSpNy/cZ3wDGYK25DFTte8/vCZMRBTPiiNSrLp/RsM
xIojRcLqzARwpvPfFZ8psASKei9+5oIICUrNvwwQGtjepvZwdFQEl90SKaHw8kMf
sP9rxuqlEN5ec6xnMTUgwfnyBZgNIMSeb4KVPP1rxN2eAa5+bK1OlQ==
=gyyY
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10apr20-take2' of git://git.denx.de/u-boot-dm
Functions for reading indexed values from device tree
Enhancements to 'dm' command
Log test enhancements and syslog driver
DM change to read parent ofdata before children
Minor fixes
'bootefi hello' is used in one of the Python tests.
efidebug can be used to verify the correct initialization of the UEFI
sub-system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromum.org>
For testing purposes enable the syslog logging driver.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
ACPI (Advanced Configuration and Power Interface) is a standard for
specifying information about a platform. It is a little like device
tree but the bindings are part of the specification and it supports an
interpreted bytecode language.
Driver model does not use ACPI for U-Boot's configuration, but it is
convenient to have it support generation of ACPI tables for passing to
Linux, etc.
As a starting point, add an optional set of ACPI operations to each
device. Initially only a single operation is available, to obtain the
ACPI name for the device. More operations are added later.
Enable ACPI for sandbox to ensure build coverage and so that we can add
tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Adding those extra configurations allows us to successfully run UEFI
secure boot pytest on Travis CI.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
CONFIG_SMBIOS_MANUFACTURER="amlogic"
CONFIG_SMBIOS_PRODUCT_NAME="p200"
is incorrect for the ODROID-C2.
Show correct board name and manufacturer in SMBIOS.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Enable these standard U-Boot commands for image manipulation and for
starting the default boot command using 'boot' command in U-Boot shell.
Cc: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a121 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add DT entries, Kconfig entries and board-specific entries to configure
FMC2 bus and make KS8851-16MLL on that bus accessible to U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
- Misc enhancements to Clearfog, including board variant detection
(Joel)
- Misc enhancements to Turris Mox, including generalization of the
ARMADA37xx DDR size detection (Marek)
In order to support MOX boards with 2 GB or 4 GB RAM, we use the new
Armada-3700 generic code for memory information structures. This is done
by removing dram_init and dram_init_banksize from turris_mox.c, in order
for the generic, weak definitions to be used.
Also for boards with 4 GB RAM it is needed to increase
CONFIG_NR_DRAM_BANKS to 2 in turris_mox_defconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Patch Linux's device tree according to which Mox modules are connected.
Linux's device tree has all possible Mox module nodes preprogrammed, but
in disabled state.
If MOX B, MOX F or MOX G module is present, this code enables the PCI
node.
For the network modules (MOX C, MOX D and MOX E) are present, the code
enables corresponding ethernet and swtich nodes and DSA connections.
For the SFP cage the SFP GPIO controller node and SFP node are also
enabled.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Migrate the values for ENV_SIZE and ENV_OFFSET into board specific
Kconfig defaults so they're more accessible for configuration.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
- As there is a requirement to store certain data, we need a persistent
storage in u-boot. Hence, we need to save env in NAND
- Add default Guardian environment variables
- Update partition table:
- Reserve some space for experimentation, this ensures proper
backwards compatibility
- Update defconfig accordingly
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
This patch enables the guardian board to provide feedback
about the boot stage in headless mode. The on-board led
would behave in the following pattern
* U-boot -> GLOW LED
* Linux -> BLINK LED [HEART-BEAT PATTERN]
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
- On Guardian board, usb-eth boot in SPL stage fails due to certain
misconfiguration. Hence, add the same to fix the issue.
- configs are set based on the conditional statement present in
arch/arm/mach-omap2/am33xx/board.c
- disable tiny printf in SPL stage:
As the library is optimized, the ability to deal with ethaddr is lost.
The following message would be printed on the console,
Error: flags type check failure for "ethaddr" <= "80a81144M" (type: m)
Error inserting "ethaddr" variable, errno=1
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
Add and enable RTC-backed boot counter on ABB SECU1 platform.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
- sync all Amlogic DT from Linux v5.6-rc2
- MMC clock fixups
- add support for Libre Computer AML-S905D-PC and AML-S912-PC
-----BEGIN PGP SIGNATURE-----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=PiOt
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200406' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic into next
- clk: meson-g12a: missing break
- sync all Amlogic DT from Linux v5.6-rc2
- MMC clock fixups
- add support for Libre Computer AML-S905D-PC and AML-S912-PC
Enable support for Gigadevice/ISSI flash parts for Versal platform.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
With multi defconfig NOR flash information about NOR should be taken from
DT that's why there is no reason to specify address and sizes via fixed
config.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are a lot of zynq configurations which can be merged together and use
only one for all. The similar change has been done for ZynqMP by commit
be1b6c32d9 ("arm64: zynqmp: Use zynqmp_virt platform")
Build SPL with u-boot.img for zc706 like this.
export DEVICE_TREE=zynq-zc706 && make xilinx_zynq_virt_defconfig && make -j8
u-boot.img is generic for all boards.
Tested on Zybo, zc702, zc706, zc770-xm011-x16, cc108 and microzed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable cache commands by default for mtest configuration. It is good to be
able to enable/disable caches when you test memory.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add DISTRO_DEFAULTS config to versal virt defconfig file which is
suitable for booting general purpose Linux distributions. Remove
other configs which are selected by default by DISTRO_DEFAULTS
configuration.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the Amlogic based libretech-pc platform.
This platform comes with 2 variant, based on the s905d or s912 SoC.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: update board/amlogic/q200/MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Jetson Nano Developer Kit is a Tegra X1-based development board. It
is similar to Jetson TX1 but it is not pin compatible. It features 4GB
of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot
used for storage.
HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0
and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI
Ethernet controller provides onboard network connectivity. NVMe support
has also been added. Env save is at the end of QSPI (4MB-8K).
A 40-pin header on the board can be used to extend the capabilities and
exposed interfaces of the Jetson Nano.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
This allows the user to set $serverip in the environment before
executing a DHCP request. If they do, U-Boot will use that IP rather
than using the IP in the DHCP response.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
U-Boot is configured to build as position independent executable. Enable
relocation of RELA section required to work with different load
addresses.
Signed-off-by: Vishruth <vishruthj@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Peter Robinson <probinson@gmail.com>
This series fixes:
* UEFI Python tests CONFIG_OF_CONTROL=y.
* int to pointer cast warning for cmd/efidebug.c
* memory reservation even if fdt node is disabled
Now that the Python test is fixed reintroduce the reverted patch for
vexpress_ca9x4 to enable EFI_LOADER and define the dtb file name.
-----BEGIN PGP SIGNATURE-----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=Cgg0
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-04-rc5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc5
This series fixes:
* UEFI Python tests CONFIG_OF_CONTROL=y.
* int to pointer cast warning for cmd/efidebug.c
* memory reservation even if fdt node is disabled
Now that the Python test is fixed reintroduce the reverted patch for
vexpress_ca9x4 to enable EFI_LOADER and define the dtb file name.
CONFIG_ENV_ADDR helps in picking environment from flash before DDR init.
Define the value as 0x20500000 for lx2160ardb and lx2160aqds.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable FSPI controller support. So, flash environment can now be used.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The eMMC HS200 speed mode on Layerscape platforms has not been
supported properly. The eSDHC clock tuning has not been implemented
by now. So disable it until it is supported properly in case of
any potential issues.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add config to enable the PFE and ETH support.
Also change the pfe secure boot header address.
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable CONFIG_DM_USB to remove below compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
With DM_USB enabled, enable CONFIG_BLK to remove this
compile warning for ls1012afrdm based targets:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1046A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1043A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable DM_SPI and DM_SPI_FLASH in U-Boot on V2H Blanche.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
mmc bootbus and partconf commands are needed in order to be able to
configure booting from separate boot0/boot1 eMMC partitions.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[jagan: rebase on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
EFI was disabled in f95b8a4b5f because of the missing DTB file,
and indeed, the DTB file is required to load recent versions of GRUB
(2.04) correctly.
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
Currently this causes failures of the platform when running the EFI
loader tests, so disable it for now.
This reverts commit af827140e5.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently the following error message is seen during boot:
U-Boot 2020.01-08751-g55759ae141 (Mar 09 2020 - 14:44:52 -0300)
Model: Elgin RV1108 R1 board
DRAM: 128 MiB
APLL: 600000000 DPLL:1200000000 GPLL:1188000000
ACLK_BUS: 148500000 ACLK_PERI:148500000 HCLK_PERI:148500000 PCLK_PERI:74250000
MMC: dwmmc@30110000: 0
Loading Environment from MMC... OK
In: serial@10210000
Out: serial@10210000
Err: serial@10210000
Model: Elgin RV1108 R1 board
rockchip_dnl_key_pressed: adc_channel_single_shot fail!
....
Since the elgin-rv1108 does not use ADC to read the download
key status, select CONFIG_ROCKCHIP_BOOT_MODE_REG=0 to avoid
such error.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Since commit 8e9a8d0d0c ("rockchip: elgin-rv1108: use board_early_init_f
for per-boar init") the function that configure the board GPIOs is no
longer called since CONFIG_BOARD_EARLY_INIT_F=y is not selected.
These GPIOs do not need to be configured in such early stagem, so change it
to rk_board_late_init() and also select CONFIG_BOARD_LATE_INIT=y
to fix the regression.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
These boards aren't ChromeOS devices so won't have a cros-ec-keyb
input as it's the keyboard available via the ChromeOS Embedded
Controller. Update them to use a USB keyboard which would actually
be available. Also enable the usb keyboard option for those devices
that don't have it enabled already.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
EFI was disabled in f95b8a4b5f because of the missing DTB file,
and indeed, the DTB file is required to load recent versions of GRUB
(2.04) correctly.
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
Now that those common Allwinner config symbols are defined automatically
for all boards in their Kconfig files, we can remove the now redundant
definitions from the boards' _defconfig files.
Some boards had a differing definiton for some of those symbols, it
looks like mostly to "merge races" when the symbol was introduced (new
board *_defconfig file missed the "add symbol to all files" patch).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Pine H64 board comes with some onboard SPI flash chip, which is
perfect for loading SPL, ATF and U-Boot proper from there.
Enable the functionality in the defconfig, so that we use sunxi-fel to
transfer a bootable image to the NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
K3 J721E:
* OSPI boot support
* Support for loading remote cores in R5 SPL
* PMIC ESM Support
* Minor fixes for R5F and C7x remoteproc drivers
K3 AM654:
* Update AVS class 0 voltages.
* Add I2C nodes
DRA7xx/AM57xx:
* Fixed Android boot on AM57xx
AM33/AM43/Davinci:
* switch to driver model for the net and mdio driver for baltos
* Add DM/DTS support for omap video driver
* Enable fastboot on am335x-evm
In a few boards we had overridden, intentionally, the value used for
CONFIG_SPL_LDSCRIPT. However, rather than using the ARCH value (arm)
they used the $(ARCH) variable in make. This doesn't help really, so
switch to a hard-coded value.
Signed-off-by: Tom Rini <trini@konsulko.com>
As there is only one machine under mach-orion5x, having a Kconfig entry
for SPL_LDSCRIPT is not helpful, move this to the defconfig file.
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
As there is only one mx31pdk config file and with upcoming updates to
the Kconfig parsing logic, rather than have an entry in
board/freescale/mx31pdk/Kconfig, move this single setting to the
defconfig file.
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Magnus Lilja <lilja.magnus@gmail.com>
This pull request provides the hardware RNG driver for Amlogic systems needed
for the EFI_RNG_PROTOCOL.
Furthermore bug fixes are provided:
* correct an error message in the efidebug command
* correct an error in the 'efidebug rm' command
* remove an unnecessary assignment in efi_queue_event()
-----BEGIN PGP SIGNATURE-----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=fiKc
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-04-rc4-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc4 (3)
This pull request provides the hardware RNG driver for Amlogic systems needed
for the EFI_RNG_PROTOCOL.
Furthermore bug fixes are provided:
* correct an error message in the efidebug command
* correct an error in the 'efidebug rm' command
* remove an unnecessary assignment in efi_queue_event()
We want to always run RSA library test on sandbox build in Travis CI.
Just adding CONFIG_RSA_VERIFY_WITH_PKEY would be good enough for this
purpose.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
For all sandbox systems with DM_RNG we enable RNG_SANDBOX. So we can simply
set the default to yes.
All rng drivers depend on DM_RNG. Use a single 'if' instead of individual
dependencies. Now 'make menuconfig' shows the individual drivers neatly
indented under the DM_RNG entry.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Additions have been made to the non-HS defconfig without the same
being made to the HS defconfig, sync them.
Signed-off-by: Andrew F. Davis <afd@ti.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl5nWr8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyGaOCACkavhqX4EP1FeRDX7m
Uujnacekt0y0uC54aGqBZ2u8Y+iwFza7rd4RcWOAx1pHq1QggAF+h5So8cOfSjpD
6Uad4ql0EOYuH5xcFYCzmEmOMj25DrIZ0F+nPnxhdK0novBrUO8QD2v4r8TgrcWs
dFxe7RCvop4I54Bq14LzZsCozlYEqHaf5E3fSas2LVeDIBrkzGh6pYhWM62FFRuy
71kIC+y9pfRPXaeiOSDp1ZqPkzQA8xw5AWAx4TCmTZ1DjLLBAoRbe0Iv9fseHct0
BFGD4+G1g0GfrNrjAG2OPAePDXq+6fmoAZFbkDGeoFwGnZXhxEnVnN4w5t+Hl0H4
82tF
=eO+8
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2020.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2020.04 cycle:
- Includes two small configuration fixes that will solve the SPL booting
on sama5d3_xplained board.
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Booting a mainline kernel in secure mode on i.MX7D causes only
one CPU to be brought up.
Change it to booting in non secure mode by default, which
allows the two CPUs to be brought up.
It does have a side effect of not probing the CAAM driver.
If CAAM driver is needed then a secure world OS such as OPTEE needs
to be used.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Convert imx6sabresd ethernet to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On the aristainetos2c boards the PMIC needs to be initialized,
because the Ethernet PHY uses a different regulator that is not
setup per hardware default. This does not influence the other
versions as this regulator isn't used there at all.
Signed-off-by: Heiko Schocher <hs@denx.de>
With CONFIG_SUPPORT_EMMC_BOOT moved to Kconfig, move it to defconfig
files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add initial support for the ABB SECU board, which is an ArriaV-based
SoCFPGA system with ethernet and booting from Denali NAND.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This config option was present in am335x_boneblack_defconfig, but we
have to use generic am335x_evm_defconfig now, as BBB defconfig was
removed in commit 8fa7f65dd0 ("configs: Remove
am335x_boneblack_defconfig"). So this patch merely brings that option
back.
Tested on BeagleBone Black:
=> fastboot 0
$ fastboot flash rootfs rootfs.img
Fixes: 8fa7f65dd0 ("configs: Remove am335x_boneblack_defconfig")
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
DFU over TFTP flashing method might be helpful in order to speed-up the
flashing process of big images (as DFU works over USB EP0, which is
quite slow). Also, it's a good backup option in the case when USB got
broken (either in software or hardware), to avoid resorting to SD card
boot.
This config option was present in am335x_boneblack_defconfig, but we
have to use generic am335x_evm_defconfig now, as BBB defconfig was
removed in commit 8fa7f65dd0 ("configs: Remove
am335x_boneblack_defconfig"). So this patch merely brings that option
back.
Tested on BeagleBone Black:
=> setenv dfu_alt_info $dfu_alt_info_emmc
=> setenv ipaddr 192.168.0.100
=> setenv serverip 192.168.0.1
=> setenv updatefile update_uboot.itb
=> dfu tftp mmc 1
Where 'update_uboot.its' file looks like this:
/dts-v1/;
/ {
description = "Automatic U-Boot update";
#address-cells = <1>;
images {
u-boot.img.raw-1 {
description = "U-Boot binary";
data = /incbin/("u-boot.img");
compression = "none";
type = "firmware";
load = <0x60000>;
hash-1 {
algo = "sha1";
};
};
};
};
And 'update_uboot.itb' is generated as follows:
$ mkimage -f update_uboot.its update_uboot.itb
Newly flashed U-Boot works fine.
Fixes: 8fa7f65dd0 ("configs: Remove am335x_boneblack_defconfig")
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
Enable ESM modules for both PMIC and SoC side for proper watchdog
handling on the board.
SPL_BOARD_INIT is also enabled so that the board init function
probing the drivers is called.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Remove saving ENV in eMMC in R5 as the power domains are not
setup. Environment in eMMC cannot be read if we do not boot from
eMMC.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Enable R5F remoteproc support in R5 defconfig so that R5s can
be started in SPL. While at it enable the SPL_FS_EXT4 config
option to load the firmwares from file system.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
- Enable ADMA and HS400 for the eMMC driver on 64-bit SoCs
- Add some convenient environment variables to handle SD card
- Sanitize the NAND controller reset sequence and its WP handling
- Sync DT with Linux
-----BEGIN PGP SIGNATURE-----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=h4lQ
-----END PGP SIGNATURE-----
Merge tag 'uniphier-v2020.04-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier
UniPhier SoC updates for v2020.04 (3rd)
- Enable ADMA and HS400 for the eMMC driver on 64-bit SoCs
- Add some convenient environment variables to handle SD card
- Sanitize the NAND controller reset sequence and its WP handling
- Sync DT with Linux
The board uses 100 MHz clock for UART bitrate generator,
but is configured as 50 MHz on defconfig.
This produces wrong console output.
The first message, "Debug uart enabled" is received as:
"������b"
Fix the issue by configuring the correct clock for the
UART baudrate generator
Signed-off-by: Milan Obuch <u-boot@dino.sk>
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The eMMC controller on LD20 or later supports HS-400 mode. It works on
a quick test. Enable it in case somebody may want to use it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This fixes the inadvertent definition of CONFIG_DTB_RESELECT and
CONFIG_MULTI_DTB_FIT in the K2x HS defconfigs, that happened as part of
a resync of the defconfigs.
The inclusion of these config options causes ethernet to stop working on
K2x HS devices as they interfere with the installation of the secure
boot monitor.
This patch also removes the above configs for the K2 GP devices, as they
are not needed, and to keep the differences between the GP and HS
defconfigs to a minimum.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
When the board was originally submitted, it was attempting to use the
ESDHC driver. The board uses the USDHC driver.
Signed-off-by: Carl Gelfand <carl@novtech.com>
Cc: Shawn Guo <shawn.guo@kernel.org> (maintainer:MEERKAT96 BOARD)
Acked-by: Shawn Guo <shawnguo@kernel.org>
This reverts commit 02dc1599ba
Commit 02dc1599ba ("configs: enable sata, eSDHC, USB device module in
T2080QDS")
has some sata defconfig changes to fit support DM mode, Now the driver
will be reverted, So revert it.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There are many boards share the board file and device header file with
rk3399 evb, add target type MACRO so that it is fixed instead of default
to the first target in "RK3399 board select".
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Added support for onboard LED's and push button. When powered board will be
in low power mode(yellow LED), on button press, board enters full power mode
(red LED) and boots u-boot.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
roc-pc-rk3399 board has one user button & three user LED's. Currently
we don't have any code support for these devices. Since button and LED's are
specific to roc-pc-rk3399 board, split it into its own board file and add code
support here.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl5GcB0ACgkQ4rK92eCq
k3Wr9gf/dDPJi6UBhLDio/IVKDBddOEUN0Lwdr9W0upL+DrdvEOyNyMSEKuLccIE
UTd1NmNNwcvgDRaPvB5o3R7twWItTW0cYlmVkFSZ228aq6xdf/SElN2OUD6B9Gh+
8bi6oVLu41TNMYn4VYxsEftcT2megfH8s+SH/FlvR5ua1yCC1vyrytEQjPIbJAB2
sa90ewDyp5EYqGLdAk6AVjPLeNZsaleGwuyLf04PoC2xhn+3HTEKJCJN4O46aJUr
0GUI7YN7pTjIfZdYfFqjcwoQV1xV2HtbjCTcOb8Td8TEYjIoILF8tSyfIwDXWGB5
zMQIQxUdQyNiqdBPFcnkAufjk+zLIQ==
=0dG+
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200214' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- add DH Electronics DHCOM SoM and PDK2 board
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
Add mmc device partition 0 as the seat of the environment.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP15xx and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
It's a very rare if at all existing occasion when ARC CPU template
is used as is w/o any changes - in the end it's a beauty and competitive
advantage of ARC cores to be tailored for a particular use-case - and
so it doesn't make a lot of sense to offer template-based "-mcpu" selection.
Given for each and every platform we end-up adding quite a few more flags
it's logical to move "-mcpu" selection to platform's definition as well
which we exactly do here.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Given now nsim_hs38 configuration is usable on QEMU and in QEMU
we have Virtio working perfectly fine the next logical step
is to add support of supported & known to work net & bkl to this
config.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We don't have yet any brc700 or big-enadian platforms with networking
support to run this particular configuration.
Whenever QEMU for ARC supports arc700 or big-endian targets we may revisit
this one.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Since v2019.06 DesingWare nSIM supports DesignWare UART simulation
and so we may switch from pretty unusual ARC UART to much more standard
DesignWare UART (which in case of U-Boot is just an ordinary 16650 UART).
This among other things makes built dinaries compatible with our other
platforms to name a few: FPGA-based HAPS boards, QEMU and even ZeBU.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
- Move P2SB from Apollo Lake to a more generic location
- Add a function to find a device by drvdata in DM core
- Enhancement of DM IRQ uclass driver
- Add a clock driver for Intel devices
- Add support for ACPI general-purpose events
- Add a TPM driver for H1/Cr50
- Enable TPM on Google Chromebook Coral
