The subdivision name "TQ Components" hasn't been in use for a long time.
Rename the vendor directory to "tq", which also matches our Device Tree
vendor prefix.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Get Unique ID of SoC iMX7ULP, using the logic described in Fusemap
(IMX7ULPRMB2_Rev0_Fusemap) attached in the i.MX 7ULP APRM [1].
[1]
https://www.nxp.com/docs/en/reference-manual/IMX7ULPRMB2.pdf
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
i.MX8MP has two ENET controllers, have to update the function to
enable loading two MAC addresses.
Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Make use of the host Kconfig for FIT. With this we can use
CONFIG_IS_ENABLED(FIT) directly in the host build, so drop the unnecessary
indirection.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
After switch to use binman, no need to use the bash script
to check file exsiting or not. And there is bug that
the script will be executed everytime Makefile is used which is
confusing people.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The Kontron SoM-Line i.MX8MM (N801x) by Kontron Electronics GmbH is a SoM
module with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC.
The matching evaluation boards (Board-Line) have 2 Ethernets, USB 2.0, HDMI/LVDS,
SD card, CAN, RS485 and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.
Currently there are the following SoM flavors (SoM-Line):
* N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
* N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
* N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND
And the according evaluation boards (Board-Line):
* N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
* N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
* N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...
Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Update the mx7ulp wdog disable sequence to avoid potential reset
issue in unlock or refresh sequence. Both sequence need two words
write to wdog CNT register in 16 bus clocks window, if miss the
window, the write will cause violation in wdog and reset the chip.
Current u-boot code is using writel() function which has a DMB
barrier to order the memory access. The DMB between two words write
may introduce some delay in certain circumstance, causing the wdog
reset due to 16 bus clock window requirement.
Also, WDOG1 might have been enabled already depending on FUSE hence
we need to be as close as possible to its reconfiguration timing
requirement of 128 bus clock limit.
This patch replaces writel() function by __raw_writel() to avoid such
issue, and improve to check if watchdog is already disabled or
unlocked.
Signed-off-by: Ye Li <ye.li@nxp.com>
Co-developed-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Co-developed-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Since derivatives are moving to binman from usage of the FIT generator
script, and considering the warning introduced in f4a43d2925
("Makefile: Warn against using CONFIG_SPL_FIT_GENERATOR"), usage of FIT
generator is discouraged.
Current FIT generator also generates broken output, since commit
3f04db891a ("image: Check for unit addresses in FITs") prohibits using
'@' for unit addresses but the generator script still emits the old
sematics.
Remove the generator script and corresponding call in Makefile, all
derivatives should be migrated to binman in order to provide binary
images.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently imx8mm-cl-iot-gate_defconfig fails to produce a working boot
binary due to the lack of fip.bin:
" BINMAN all
Image 'main-section' is missing external blobs and is non-functional: blob-ext
Some images are invalid"
To make the build process more consistent with the other i.MX8M targets,
split the defconfig in two:
- imx8mm-cl-iot-gate_defconfig: standard defconfig that only
requires ATF / DDR firmware.
- imx8mm-cl-iot-gate-optee_defconfig: "more advanced" defconfig that
requires ATF / Optee / mbedtls / DDR firmware.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
When TEE is loaded, we need to restrict the memory usage based
on rom_pointer[0]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
cherry-picked from NXP code:
719d665a87c6: ("MLK-20467 imx8m: Fix issue for booting signed image through uuu")
which fixes secure boot on imx8m based boards. Problem was
that FIT header and so IVT header too, was loaded to
memallocated address. So the ivt header address coded
in IVT itself does not fit with the real position.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tim Harvey <tharvey@gateworks.com>
read the address where the IVT header must sit
from IVT image header, loaded from SPL into
an malloced buffer and copy the IVT header
to this address
May make this dependend on SoC ?
Signed-off-by: Heiko Schocher <hs@denx.de>
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly. Then, include
<linux/mtd/rawnand.h> where required directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This config is only used by three boards with this SOC. Most other
platforms derive this information from devicetree, and are unlikely
to ever need this config.
Moreover, it is confusing when Kconfig asks for this value under
"Support OPTEE images", but does not do anything with the value.
Move it to imx7 for those boards who still make use of it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This function is clearly architecture specific code, not board specific
code. The only difference from the previous arm arch_lmb_reserve() is the
extra reservation of 16k of memory below the stack bottom, rather than
the 4k. The common code now also uses 16k alignment. Remove this custom
implementation, as it now behaves exactly as the common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Hai Pham <hai.pham.ud@renesas.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ye Li <ye.li@nxp.com>
No iMX platforms have supported ATAG-based booting. They have however
re-used the CONFIG_SERIAL_TAG option as a way to enable support of
reading the OTP fuses and setting the serial# environment variable in
some cases. Change the warp7 support to use this symbol, use this for
updating the rest of the imx7 code, and update the imx8 conditionals.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Provide a default Kconfig value of the default script
- Largely continue to define this via the board Kconfig file
- For the boards that select a script based on defconfig rather than
TARGET, keep this within the defconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, there is no over-arching symbol for access to
arch/arm/mach-imx nor the CONFIG symbols that are common over all of
these related platforms. This new CONFIG symbol will allow us to start
down this path.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART
Log as below: I would keep some debug info for now, and after we move
to be stable and production launch, we could drop that.
U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
Normal Boot
upower_init: soc_id=48
upower_init: version:11.11.6
upower_init: start uPower RAM service
user_upwr_rdy_callb: soc=b
user_upwr_rdy_callb: RAM version:12.6
Turn on switches ok
Turn on memories ok
Clear DDR retention ok
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F0 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
complete
De-Skew PLL is locked and ready
WDT: Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x3a800 by ROM_API
NOTICE: BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94
NOTICE: BL31: Built : 01:56:58, Jun 29 2021
NOTICE: upower_init: start uPower RAM service
NOTICE: user_upwr_rdy_callb: soc=b
NOTICE: user_upwr_rdy_callb: RAM version:12.6
U-Boot 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
CPU: Freescale i.MX8ULP rev1.0 at 744 MHz
Reset cause: POR
Boot mode: Single boot
Model: FSL i.MX8ULP EVK
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... ***
Warning - bad CRC, using default environment
In: serial@293a0000
Out: serial@293a0000
Err: serial@293a0000
Net:
Warning: ethernet@29950000 (eth0) using random MAC address -
96:35:88:62:e0:44
eth0: ethernet@29950000
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When booting from boot part1/2, the image offset should be 0, but
ROM has a bug to return 0x8000. Has to workaround the issue before
ROM fix it.
Use a ROM function to know boot from emmc boot part or user part
So we can set the image offset accordingly.
Signed-off-by: Ye Li <ye.li@nxp.com>
Since CMC1 MR0 only reflects high 16 bits boot cfg used for AP domian,
it does not connect to low 16 bits for RTD. So we can't get the correct
boot mode.
Change to use DGO_GP5 of SEC_SIM which is set by ROM.
Signed-off-by: Ye Li <ye.li@nxp.com>
The CMC1 SRS reflects the current reset cause, not SSRS.
Then you could get "Reset cause: WARM-WDG" when issue reset in U-Boot.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Need probe the S400 MU device in arch_cpu_init_dm, so we can use
S400 API in u-boot
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Rlease LPAV from RTD to APD
Release gpu2D/3D to APD
Set TRDC MBC2 MEM1 for iomuxc0 access
Since upower depends AP/M33 SW to configure IOMUX for its PMIC i2c
and MODE pins. we have to open iomuxc0 access for A35 core (domain 7)
in single boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
There is xrdc inside i.MX8ULP, we need to configure permission to make
sure AP non-secure world could access the resources.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since S400 will set the memory of SPL image to R/X. We can't write
to any data in SPL image.
1. Set the parameters save/restore only for u-boot, not for SPL. to
avoid write data.
2. Not use MU DM driver but directly call MU API to send release XRDC
to S400 at early phase.
3. Configure the SPL image memory of SRAM2 to writable (R/W/X)
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because we have set reset vector to ATF in SPL, have to set it back
to ROM for any reset in u-boot
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SRAM2 is half L2 cache and default to SRAM after system boot.
To enable the full l2 cache (512KB), it needs to reset A35 to make
the change happen.
So re-implement the jump entry function in SPL:
1. configure the core0 reset vector to entry (ATF)
2. enable the L2 full cache
3. reset A35
So when core0 up, it runs into ATF. And we have 512KB L2 cache working.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8ULP support using ROM API to load container image,
it use same ROM API as i.MX8MN/MP, and use same container format
as i.MX8QM/QXP.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since the container is shared among i.MX platforms, move its header file
to mach-imx
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add basic i.MX8ULP support
For the MMU part, Using a simple way the calculate the MMU size to avoid
default heavy calcaulation. And align address and size in the table
settings to 2MB or 4GB as much as possible. So we can reduce the 4K page
allocations in MMU table which will spends much time in create the
page table
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
As the deadline for migration to DM_USB, when using a USB host
controller has now gone two years past the deadline, enforce migration.
This is done by:
- Ensuring that all host controller options (other than the very legacy
old MUSB ones) now select USB_HOST. USB_HOST now enforces DM_USB and
OF_CONTROL.
- Remove other parts of Kconfig logic that had platforms pick DM_USB.
- To keep Kconfig happy, have some select statements test for USB_HOST
as well.
- Re-order some Kconfig entries and menus so that we can cleanly pick
host or gadget roles. For the various HCD options that have platform
glue options, group them together and update dependencies in some
cases.
- As SPL_DM_USB is not required, on platforms that had not yet enabled
it, disable it.
Cc: Marek Vasut <marex@denx.de>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Samuel Holland <samuel@sholland.org>
Cc: FUKAUMI Naoki <naobsd@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add clock function to setup relevant clocks for USB3.0 controllers and
PHYs on i.MX8MQ
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Patrick Wildt <patrick@blueri.se>
In case the iMX8M boot from eMMC boot partition and the primary image
is corrupted, the BootROM is capable of starting a secondary image in
the other eMMC boot partition as a fallback.
However, the BootROM leaves the eMMC BOOT_PARTITION_ENABLE setting as
it was, i.e. pointing to the boot partition containing the corrupted
image, and the BootROM does not provide any indication that this sort
of fallback occured.
According to AN12853 i.MX ROMs Log Events, Rev. 0, May 2020, it is
possible to determine whether fallback event occurred by parsing the
ROM event log. In case ROM event ID 0x51 is present, fallback event
did occur.
This patch implements ROM event log parsing and search for event ID
0x51 for all iMX8M SoCs, and based on that corrects the eMMC boot
partition selection. This way, the SPL loads the remaining boot
components from the same eMMC boot partition from which it was
started, even in case of the fallback.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Harald Seiler <hws@denx.de>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Make macros actually use passed parameter instead of local variables
that happen
to be named the same as symbols in macro expansion.
Signed-off-by: Kacper Kubkowski <kkubkowski@fluence.pl>
Some IPs have their accessible address space restricted by the
interconnect. Let's make sure U-Boot only ever uses the space below
the 4G address boundary (which is 3GiB big), even when the effective
available memory is bigger.
We implement board_get_usable_ram_top() for all i.MX8M SoCs, as the
whole family is affected by this.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.
Based on the original U-Boot work done by Phytec.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ()
macro, which expands the value provided to the Hz range without taking into
account the precise Hz setting. This causes the frequency of 266 MHz not ot
be found in the imx8mm_fracpll_tbl, since it is entered there with a
precise Hz value. This in turn causes the boot hang in SPL, as proper DDR
fracpll frequency cannot be determined.
Correct the value in imx8mm_fracpll_tbl to match the one expanded by
MHZ(266) macro, rounding it down to MHz range only.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Clock initialization functionality has ambitious debug messages, which are
printed out when failures are triggered during execution:
- Separate frequency table lookup functions have the the same output that
makes it impossible to understand which function failed and produced the
output
- PLL decoding routine has a generic debug statement printed, which does
not state the actual value failed to be found
Extend the output for both cases with prefixing table lookup functions
output with function name, and report the failed value in PLL decoding
routine.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Board designed for quick prototyping and has one microSD port,
2 Ethernet ports, 2 USB ports, I2C, SPI, CAN, RS-485, GPIO,
UART interfaces, and 2 RGB LEDs.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
We need those macros to instruct drivers on how to behave for SoC specific
quirks, so let's add it as done for other i.MX SoCs.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
This mpu handling works for every i.MXRT SoC that we have, so let's
generalize imxrt1050_region_config to imxrt_region_config.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
When building imx8mp_evk_defconfig with LTO, the compiler complains
about type mismatch of function imx_eqos_txclk_set_rate() in file
drivers/net/dwc_eth_qos.c:845:12
which contains a weak definition of this function, vs file
arch/arm/mach-imx/imx8m/clock_imx8mm.c
which contains an implementation.
Change the type of this function in the implementation to fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On ARM, the gd pointer is stored in registers r9 / x18. For this the
-ffixed-r9 / -ffixed-x18 flag is used when compiling, but using global
register variables causes errors when building with LTO, and these
errors are very difficult to overcome.
Richard Biener says [1]:
Note that global register vars shouldn't be used with LTO and if they
are restricted to just a few compilation units the recommended fix is
to build those CUs without -flto.
We cannot do this for U-Boot since all CUs use -ffixed-reg flag.
It seems that with LTO we could in fact store the gd pointer differently
and gain performance or size benefit by allowing the compiler to use
r9 / x18. But this would need more work.
So for now, when building with LTO, go the clang way, and instead of
declaring gd a global register variable, we make it a function call via
macro.
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=68384
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Supported peripherals: Ethernet, eMMC, Serial.
U-Boot SPL 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14
+0200)
Normal Boot
Trying to boot from MMC2
U-Boot 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14 +0200)
CPU: Freescale i.MX8MQ rev2.1 at 1000 MHz
Reset cause: POR
Model: Ronetix iMX8M-CM SoM
DRAM: 1 GiB
WDT: Started with servicing (60s timeout)
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 (eth0) using random MAC address -
42:0d:e7:78:da:53
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
u-boot=>
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
instead using ls and awk to determine file size use stat instead.
This fixes an invalid size reporting for user or group names that have
spaces in them.
This adds a dependency on the stat application which is part of
the coreutils package which also includes ls.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose Carrier
board.
Genaral features:
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Carrier board for
creating complete i.Core MX8M Mini C.TOUCH 2.0 board.
Linux dts commit details:
commit <a142252061ff> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
C.TOUCH 2.0")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Mini EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <051c08eea682> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
EDIMM2.2 Starter Kit")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
