No one is using CONFIG_EDT32F10; remove related code.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
No one is using CONFIG_SYS_INVERT_COLORS; remove related code.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Currently, "nand scrub" runs chip->scan_bbt at the end of
nand_erase_opts() even if NAND_SKIP_BBTSCAN flag is set.
It violates the intention of NAND_SKIP_BBTSCAN.
Move NAND_SKIP_BBTSCAN flag check to nand_block_checkbad() so that
chip->scan_bbt() is never run if NAND_SKIP_BBTSCAN is set.
Also, unset NAND_BBT_SCANNED flag instead of running chip->scan_bbt()
right after scrub. We can be lazier here because the BBT is scanned
at the next call of nand_block_checkbad().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Commit 35c204d8a9 (nand: reinstate lazy bad block scanning)
broke NAND_BBT_USE_FLASH feature.
Its git-log claimed that it reinstated the change as by commit
fb49454b1b ("nand: reinstate lazy bad block scanning"), but it moved
"chip->options |= NAND_BBT_SCANNED" below "chip->scan_bbt(mtd);".
It causes recursion if scan_bbt does not find a flash based BBT
and tries to write one, and the attempt to erase the BBT area
causes a bad block check.
Reinstate commit ff49ea8977 (NAND: Mark the BBT as scanned prior to
calling scan_bbt.).
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Rostislav Lisovy <lisovy@merica.cz>
Cc: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Since commit ff94bc40af (mtd, ubi, ubifs: resync with Linux-3.14),
the "nand scrub" command has not been working.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
The QSPI controller in i.MX 6SoloX and Vybrid supports reading data using
IP register and AHB bus.
The original driver only supports reading data from IP interface. The IC
team suggests to use AHB read which is faster then IP read. Using AHB read,
we can directly memcpy, a "missed" access to the buffer will cause the
controller to clear the buffer and use the SEQID stored in bfgencr register
to initiate a read from flash device.
Since AHB bus is 64 bit width, we can not set MCR register using 32bit. In
order to minimize code change, redefine QSPI_MCR_END_CFD_LE to 64bit Little
endian but not 32bit Little endia.
Introduce a new configuration option CONFIG_SYS_FSL_QSPI_AHB. If want to
use AHB read, just define CONFIG_SYS_FSL_QSPI_AHB. If not, just ignore it.
Actually if Vybrid is migrated to use AHB read, this option can be removed and
IP read function can be discared. The reason to introduce this option
is that only i.MX SOC is tested in my side, no Vybrid platform for me.
In spi_setup_slave, the original piece code to set AHB is deleted, since
Vybrid platform does not use this to intiate AHB read. Instead, add
qspi_init_ahb_read function if defined CONFIG_SYS_FSL_QSPI_AHB.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
We should not hardcode array size of i2c_data to 3. To CONFIG_FSL_LSCH3,
there are 4 i2c interface, but not 3. So the size of i2c_data array should
be calculated using "ARRAY_SIZE(i2c_bases)".
To avoid compile error, move i2c_bases before sram_data structure which
contains i2c_data array.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
No functional change, just simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
fdt_first_subnode() returns -FDT_ERR_NOTFOUND if no subnode found.
0 is supposed to be a valid offset returns from fdt_first_subnode().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
To support bigger than 16MB size qspi flashes, spi framework uses bank
switch to access higher bank or lower bank.
In this patch, QSPI_CMD_BRRD, QSPI_CMD_BRWR, QSPI_CMD_WREAR, QSPI_CMD_RDEAR
is initialized in LUT register with related pad and length configuration.
qspi_op_pp is originally for page programming, this patch reuses this function
for bank register switch and renamed it with qspi_op_write.
Since bank or EAR register is only 1 byte length, however original qspi_op_pp
or now renamed qspi_op_write only support 4 bytes lenght as the access unit,
this will trigger data abort exception when access EAR or bank register.
This is because upper framework passes a 1 bytes pointer to qspi_op_write,
however qspi_op_write treat it as an int pointer. This patch fixes this for
accessing EAR or bank register.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Linux now also contains SPI driver, yet the name is 'snps,dw-apb-ssi'.
Fix the naming before we have to support both names.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Current code tries to find the highest valid fifo depth by checking the value
it wrote to DW_SPI_TXFLTR. There are a few problems in current code:
1) There is an off-by-one in dws->fifo_len setting because it assumes the latest
register write fails so the latest valid value should be fifo - 1.
2) We know the depth could be from 2 to 256 from HW spec, so it is not necessary
to test fifo == 257. In the case fifo is 257, it means the latest valid
setting is fifo = 256. So after the for loop iteration, we should check
fifo == 2 case instead of fifo == 257 if detecting the FIFO depth fails.
This patch fixes above issues.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Get about 40x faster access on SHEEVAPLUG MMC
Fix some SD type compatibility
Changes in v3:
- fix the HW_STATE (from linux mvsdio)
- review delays and timeouts
Changes in v2:
- increase number of loops
- remove initial delay
Changes in v1:
- review all loops, delays and timeouts
Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The ChromeOS EC keyboard is used by various different chromebooks. Peach
pi being the third board in the u-boot tree to use it (snow and peach
pit the other two). Rather then embedding the same big DT node in the
peach-pi DT again, copy the dtsi snippit & bindings documentation from
linux and include it in all 3 boards.
This slightly changes the dt bindings in u-boot:
* google,key-rows becomes keypad,num-rows
* google,key-colums becomes keypad,num-colums
* google,repeat-delay-ms and google,repeat-rate-ms are no longer used
and replaced by hardcoded values (similar to tegra kbc)
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
drivers/misc/i2c_eeprom.c fails to build unless CONFIG_FIT_SIGNATURE
is defined.
CC drivers/misc/i2c_eeprom.o
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_read':
drivers/misc/i2c_eeprom.c:15:10: error: 'ENODEV' undeclared
(first use in this function)
drivers/misc/i2c_eeprom.c:15:10: note: each undeclared identifier
is reported only once for each function it appears in
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_write':
drivers/misc/i2c_eeprom.c:21:10: error: 'ENODEV' undeclared
(first use in this function)
drivers/misc/i2c_eeprom.c:22:1: warning: control reaches end of
non-void function [-Wreturn-type]
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_read':
drivers/misc/i2c_eeprom.c:16:1: warning: control reaches end of
non-void function [-Wreturn-type]
make[2]: *** [drivers/misc/i2c_eeprom.o] Error 1
make[1]: *** [drivers/misc] Error 2
make: *** [drivers] Error 2
By the way, Sandbox (enabling CONFIG_FIT_SIGNATURE) is luckily
working depending on it.
Sandbox includes include/asm-generic/errno.h
from include/errno.h
from include/u-boot/rsa-checksum.h
from include/image.h
from include/common.h
from drivers/misc/i2c_eeprom.c
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
"err" was an unsigned variable, causing negative error codes to turn
into positive values, which are interpreted as an amount of succesfully
corrected bitflips (and thus not an error).
In particular, this resulted in that if the elm reports uncorrectable
errors (-EBADMSG), the MTD layer (and UBI) falsely succeeded.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Stefan Roese <sr@denx.de>
This allow the platform to handle a custom reset sequence.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Extract controller reset code from ahci_host_init() into separate
ahci_reset().
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
All the MPC824X boards are still non-generic boards:
A3000, CPC45, CU824, eXalion, MVBLUE, MUSENKI, Sandpoint824x, utx8245
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Josef Wagner <Wagner@Microsys.de>
Cc: Torsten Demke <torsten.demke@fci.com>
Cc: Jim Thompson <jim@musenki.com>
Cc: Greg Allen <gallen@arlut.utexas.edu>
These boards are still non-generic boards.
drivers/rtc/ds12887.c should also be removed because it can not
be built without CONFIG_ATC.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
This board is still a non-generic board.
Unused code in arch/powerpc/cpu/mpc8xx/video.c should be also deleted
because CONFIG_VIDEO_ENCODER_AD7176, CONFIG_VIDEO_ENCODER_AD7177,
CONFIG_VIDEO_ENCODER_AD7179 are not defined any more.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
This patch adds driver support for the ASIX AX88179 USB3.0 to GbE network
adapter.
Driver has been tested on the RECS5250 COM module (similar to ARDALE5250).
Testcase was DHCP and PXE boot.
Signed-off-by: Rene Griessl <rgriessl@cit-ec.uni-bielefeld.de>
Add 4k erase command support for qspi driver. reuse the 64k erase function,
but change the function name from qspi_op_se to qspi_op_erase, since it
supports 64k and 4k erase.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
According cs, use different amba_base to choose the corresponding
flash devices. If not, `sf probe 1:0` and `sf probe 1:1` will
choose the same flash device, but not different flash devices.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Use QSPI_CMD_xx instead of flash opcodes
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Intel Tunnel Creek GPIO register block is compatible with current
ich6-gpio driver, except the offset and content of GPIO block base
address register in the LPC PCI configuration space are different.
Use u16 instead of u32 to store the 16-bit I/O address of the GPIO
registers so that it could support both Ivybridge and Tunnel Creek.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This network interface card is found on the NVIDIA Jetson TK1.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
To work around potential issues with explicit cache maintenance of the
RX and TX descriptor rings, allocate them from a pool of uncached memory
if the architecture supports it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
RX and TX descriptor rings should be aligned to 256 byte boundaries. Use
the DEFINE_ALIGN_BUFFER() macro to define the buffers so that they don't
have to be manually aligned later on. Also make sure that the buffers do
align to cache-line boundaries in case the cache-line is higher than the
256 byte alignment requirements of the NIC.
Also add a warning if the cache-line size is larger than the descriptor
size, because the driver may discard changes to descriptors made by the
hardware when requeuing RX buffers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
According to the top-level README file, this configuration setting can
be used to override the number of receive buffers that an ethernet NIC
uses.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for the PCIe controller found on some generations of Tegra.
Tegra20 has 2 root ports with a total of 4 lanes, Tegra30 has 3 root
ports with a total of 6 lanes and Tegra124 has 2 root ports with a total
of 5 lanes.
This is based on the Linux kernel driver, originally submitted upstream
by Mike Rapoport.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The AS3722 provides a number of DC/DC converters and LDOs as well as 8
GPIOs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the necessary flash entry for the Spansion S25FL164K
flash. Tested on Marvell 88F6218 based design.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Added S25FL116K flash and tested on Marvell 88F6281 based system.
Signed-off-by: Adnan Ali <adnan.ali@codethink.co.uk>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add support for SST25WF040B-40I-SN flash.
Tested on T1024QDS board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Removed ramtron driver since the EMK boards are
no longer been active, and these are the only boards
used this flash driver.
Commit details for EMK zap:
"ppc/arm: zap EMK boards"
(sha1: d58a9451e7)
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
In function dfu_get_buf(), the size of allocated buffer could
be defined by the env variable. The size from this variable
was passed for memalign() without checking its value.
And the the memalign will return non null pointer for size 0.
This could possibly cause data abort, so now the value of var
is checked before use. And if this variable is set to 0 then
the default size will be used.
This commit also changes the base passed to simple_strtoul()
to 0. Now decimal and hex values can be used for the variable
dfu_bufsiz.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[TestHW: Exynos4412-Trats2]
Some pointers in function download_tail() were not checked
before the use. This could possibly cause the data abort.
To avoid this, check if the pointers are not null is added.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[TestHW: Exynos4412-Trats2]
The function mmc_block_op() is the last function before
the physicall data write, but the mmc device pointer is not
checked. If mmc device not exists, then data abort will occur.
To avoid this, first the mmc device pointer is checked.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[TestHW: Exynos4412-Trats2]
The fastboot continue command is defined to exit fastboot and continue
autoboot. This commit implements the continue command and the exiting of
fastboot only. Subsequent u-boot commands can be processed after exiting
fastboot. Autoboot should implement a boot script such as "fastboot; mmc
read <...>; bootm" to fully implement the fastboot continue function.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[TestHW: Exynos4412-Trats2]
In order to add detach functions for fastboot, make the DFU detach related
functions common so they can be shared.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[TestHW: Exynos4412-Trats2]
When receive data, the RXRDY in status register set by hardware
after a new packet has been stored in the endpoint FIFO. After,
we copy from FIFO, we clear it, make the FIFO can be accessed
again.
In the receive_data() function, this bit RXRDY has been cleared.
So, after the receive_data() function return, this bit should
not be cleared again, or else it will cause the accessing FIFO
corrupt, which will make the data loss.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Deep sleep for generic board is supported now, modify qe
deep-sleep code to adapt it.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Corrected the order of arguments in memset in run_descriptor
function. Wrong order of argumnets led to improper initialization
of members of struct type result. This resulted in RNG instantiation
error.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
we need to differentiate dual-role MACs into two types: MACs with
10GEC enumeration consistent with DTSEC enumeration(defined by
CONFIG_FSL_FM_10GEC_REGULAR_NOTATION) and other MACs without
CONFIG_FSL_FM_10GEC_REGULAR_NOTATION defined.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For DDR controller version 4.7 or newer, MRC_CYC (mode register set
cycle time) is max(tMRD, tMOD). tMRD is 4nCK, or 8nCK (RDIMM). tMOD
is max(12nCK, 15ns) according to JEDEC spec.
DDR4 is not affected by this change.
Signed-off-by: York Sun <yorksun@freescale.com>
Add Intel Tunnel Creek SPI controller support which is an ICH7
compatible device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
On most x86 boards, the legacy serial ports (io address 0x3f8/0x2f8)
are provided by a superio chip connected to the LPC bus. We must
program the superio chip so that serial ports are available for us.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Movie setup_pch_gpios() in the ich6-gpio driver to the board support
codes, so that the driver does not need to know any platform specific
stuff (ie: include the platform specifc chipset header file).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
ICH 7 SPI controller only supports byte program (02h) for SST flash.
Word program (ADh) is not supported.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
ICH 7 SPI controller only supports array read command (03h).
Fast array read command (0Bh) is not supported.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Enabled byte program support for sst flashes in sf.
Few controllers will only support BP, so this patch gives
a tx transfer flag to set the BP so-that sf will operate
on byte program transfer.
A new TX operation mode SPI_OPM_TX_BP is introduced for such SPI
controller to use byte program op for SST flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Currently if SST flash advertises SST_WP flag in the params table
the word program command (ADh) with auto address increment will be
used for the flash write op. However some SPI controllers do not
support the word program command (like the Intel ICH 7), the byte
programm command (02h) has to be used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
At present SECT_4K is the same as SST_WP so we cannot tell these apart. Fix
this so that the table in sf_params.c can be used correctly.
Reported-by: Jens Rottmann <Jens.Rottmann@adlinktech.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Few of the spi controllers are only supports array slow
read which is quite different behaviour compared to others.
So this fix on sf will correctly handle the slow read supported
controllers.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Current code does not set gpio output value in ich6_gpio_direction_output(),
fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Simon Glass <sjg@chromium.org>
The ich spi controller driver spi_xfer() tries to align reading
address to 64 bytes when doing spi data in, which causes a bug of
either infinite loop or a huge size memcpy().
Actually the ich spi controller does not have such requirement of
64 bytes alignment when reading data from spi slave devices.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The card_caps bit should denote the card capability to use DDR mode,
but we need the flag indicating that the DDR mode is active.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Block length for write and read commands is fixed to 512 bytes
when the card is in Dual Data Rate mode. If block length read from CSD
is different, make sure the driver will use correct length
in all further calculations and settings.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Since the driver doesn't work in 1.2V or 1.8V signaling level modes,
Dual Data Rate mode can be supported by the driver only if it is supported
by the card in regular 3.3V mode. So, check for a particular single
bit in card type field.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
If the MMC_MODE_DDR_52MHz flag is set in card capabilities bitmask,
it is never cleared, even if switching to DDR mode fails, and if
the controller driver uses this flag to check the DDR mode, it can
take incorrect actions.
Also, DDR related checks in mmc_startup() incorrectly handle the case
when the host controller does not support some bus widths (e.g. can't
support 8 bits), since the host_caps is checked for DDR bit, but not
bus width bits.
This fix clearly separates using of card_caps bitmask, having there
the flags for the capabilities, that the card can support, and actual
operation mode, described outside of card_caps (i.e. bus_width and
ddr_mode fields in mmc structure). Separate host controller drivers
may need to be updated to use the actual flags. Respectively,
the capabilities checks in mmc_startup are made more correct and clear.
Also, some clean up is made with errors handling and code syntax layout.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
if the card claims to be high capacity and the card
is partitioned the capacity shall still be read from
ext_csd SEC_COUNT even if the resulting capacity is
smaller than 2 GiB
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
If print_mmc_devices() was called with a '\n' separator (as done
for example by the "mmc list" command), it offset the 2-nd and
all subsequent lines by one space. Fixing this.
Signed-off-by: Lubomir Popov <l-popov@ti.com>
This converts all Tegra boards over to use driver model for I2C. The driver
is adjusted to use driver model and the following obsolete CONFIGs are
removed:
- CONFIG_SYS_I2C_INIT_BOARD
- CONFIG_I2C_MULTI_BUS
- CONFIG_SYS_MAX_I2C_BUS
- CONFIG_SYS_I2C_SPEED
- CONFIG_SYS_I2C
This has been tested on:
- trimslice (no I2C)
- beaver
- Jetson-TK1
It has not been tested on Tegra 114 as I don't have that board.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
There seem to be a few EEPROM drivers around - perhaps we should have a
single standard one? This simple driver is used for sandbox testing, but
could be pressed into more active service.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
To enable testing of I2C, add a simple I2C EEPROM simulator for sandbox.
It supports reading and writing from a small data store.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This driver includes some test features such as only supporting certain
bus speeds. It passes its I2C traffic through to an emulator.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
In order to test I2C we need some sort of emulation interface. Add hooks
to allow a driver to emulate an I2C device for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The uclass implements the same operations as the current I2C framework but
makes some changes to make it fit driver model better:
- Remove the chip address from API calls
- Remove the address length from API calls
- Remove concept of 'current' I2C bus
- Drop all existing init functions
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
The private data size is missing from the driver, so we store it at 0,
which causes problems when something overwrites memory at 0.
Fix this.
Change-Id: I6f551ee905b0064ae8343e41e46450c37c8c8c1a
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Move strlcpy() definition from drivers/usb/gadget/ether.c to
lib/string.c because it is a very useful function.
Let's add the prototype to include/linux/string.h too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
'eccstat' array elements might be used uninitialized
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
With the introducing of generic board and ARM-based cores, current
deep sleep framework doesn't work anymore.
This patch will convert the current framework to adapt this change.
Basically it does:
1. Converts all the Freescale's DDR driver to support deep sleep.
2. Added basic framework support for ARM-based and PPC-based
cores separately.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Check USB Erratum A007792 applicability. If applicable, add
corresponding property in the device tree via device tree fixup
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add a new framework for fsl usb erratum handling to standardize
erratum checking only inside Uboot. Information to kernel is passed
via a boolean property corresponding to erratum, hence eliminating
need for code duplication inside kernel
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
move usb device tree fixup code from "arch/powerpc/" to "drivers/usb/"
so that it works independent of architecture it is running on
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch changes PCIe dts node status to 'disabled' if the
corresponding controller is disabled according to serdes protocol.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The macro __iomem is defined in include/linux/compiler.h.
Let's include it rather than double __iomem defines.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.adi@gmail.com>
pl010 & pl011 have different control register offsets, setting it as per
the pl01x type.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
Receive line control uses same setting as transmit line control, also one lcrh
write is effective for both baud rate & receive line control internal update.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
UART_IBRD, UART_FBRD, and UART_LCR_H form a single 30-bit wide register which
is updated on a single write strobe generated by a UART_LCR_H write. So, to
internally update the content of UART_IBRD or UART_FBRD, a write to UART_LCR_H
must always be performed at the end.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
Although we were checking the pl01x type, seems like PL010 type was being
passed by mistake.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
Due to an uninitialised variable, when muxes were deselected, any value
could be written to the mux control register. On the PCA9548, this could
result in multiple channels being selected, thus enabling multiple
pull-up resistors, and much bus capacitance.
The fix is simply to initialise the written value to zero.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
As suggested by Pavel, here some fixes to the designware SPI driver:
- Spelling fixes
- Comment for timeout added
- Removed n_bytes completely (bits_per_word is enough for this)
- Unput clock now not defined via macro. The function to
get the clock value is now called directly from within the driver
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This patch adds the driver for the Designware master SPI controller. This
IP core is integrated on the Altera SoCFPGA. This implementation is a
driver model (DM) implementation. So multiple SPI drivers can be used.
Thats necessary, since SoCFPGA also integrates the Cadence QSPI controller
used to connect the SPI NOR flashes. Without DM, using multiple SPI
drivers is not possible.
This driver is very loosely based on the Linux driver. Most of the Linux
driver is removed. Only the polling loop for the transfer is really used
from this driver, as we don't support interrupts and DMA right now.
This is tested on the SoCrates SoCFPGA board using the SPI pins on the
P14 header.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This driver is cloned from the Altera Rockerboard.org U-Boot
repository. I used this git tag: ACDS14.0.1_REL_GSRD_RC2. With Some
modification to support the U-Boot driver model (DM).
As mentioned above, in this new version I ported this driver to the
new driver model (DM). One big advantage of this move is that now
multiple SPI drivers can be enabled on one platform. And since the
SoCFPGA also has the Designware SPI master controller integrated,
this feature is really needed to support both controllers.
Because of this, this series needs the DT support for SoCFPGA
to be applied. For DT based probing in the SPI DM.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
VSC8514 QSGMII PHY requires enabling auto-negotiation,
otherwise it wouldn't work.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
fm_standard_init() initializes each 10G port by FM_TGEC_INFO_INITIALIZER.
but it needs different implementation of FM_TGEC_INFO_INITIALIZER on different SoCs.
on SoCs earlier(e.g. T4240, T2080), the notation between 10GEC and MAC as below:
10GEC1->MAC9, 10GEC2->MAC10, 10GEC3->MAC1, 10GEC4->MAC2
on SoCs later(e.g. T1024, etc), the notation between 10GEC and MAC as below:
10GEC1->MAC1, 10GEC2->MAC2
so we introduce CONFIG_FSL_FM_10GEC_REGULAR_NOTATION to fit the new SoCs on
which 10GEC enumeration is consistent with MAC enumeration.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for Freescale T1024/T1023 SoC.
The T1024 SoC includes the following function and features:
- Two 64-bit Power architecture e5500 cores, up to 1.4GHz
- private 256KB L2 cache each core and shared 256KB CoreNet platform cache (CPC)
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- Four MAC for 1G/2.5G/10G network interfaces (RGMII, SGMII, QSGMII, XFI)
- High-speed peripheral interfaces
- Three PCI Express 2.0 controllers
- Additional peripheral interfaces
- One SATA 2.0 controller
- Two USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/eSDHC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Two 8-channel DMA engines
- Multicore programmable interrupt controller (PIC)
- LCD interface (DIU) with 12 bit dual data rate
- QUICC Engine block supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Differences between T1024 and T1023:
Feature T1024 T1023
QUICC Engine: yes no
DIU: yes no
Deep Sleep: yes no
I2C controller: 4 3
DDR: 64-bit 32-bit
IFC: 32-bit 28-bit
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Some UDIMMs have faulty SPD with wrong mapping for DQ[36-39].
Using raw card spec in case this error is detected.
Signed-off-by: York Sun <yorksun@freescale.com>
In B4860QDS board SerDes2 lanes EFGH either go to SFP or AMC riser card
slot2 so either DTSEC3/DTSEC4 or TGEC1/TGEC2 should be accessible. This
Patch enables DTSEC3/DTSEC4 or TGEC1/TGEC2 on bases of user specified
string fsl_b4860_serdes2:sfp_amc=amc or fsl_b4860_serdes2:sfp_amc=sfp
respectively in hwconfig.
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We need following changes to make xfi work on B4:
1. set cross-point switch VSC3308 to use sfp config when running xfi;
2. add 10G interface check for xfi;
3. set phy address for xfi so the 10G ports can be registered by mdio;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for Cortina CS4315/CS4340 10G PHY.
- This driver loads CS43xx firmware from NOR/NAND/SPI/SD device
to initialize Cortina PHY.
- Cortina PHY has non-standard offset of PHY ID registers, thus
we define own get_phy_id() to override default get_phy_id().
- To define macro CONFIG_PHY_CORTINA will enable this driver.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Increase write-to-write and read-to-read turnaround time for two-slot DDR
configurations. Previously only quad-rank and two dual-rank configurations
have this additional turnaround time. A recent test on two single-rank
DIMMs shows the shorter additional turnaround time is also needed.
Signed-off-by: York Sun <yorksun@freescale.com>
fman_port_enet_if() tests if FM1_DTSEC2 or FM1_DTSEC4 uses
RGMII or MII and if not returns PHY_INTERFACE_MODE_NONE.
This excludes testing for SGMII further down.
Remove the unconditional "else return PHY_INTERFACE_MODE_NONE"
so SGMII can be tested too.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Reviewed-by: York Sun <yorksun@freescale.com>
The same problem that is seen on some OMAP3 is also seen on some OMAP4
so include them in the test in order to prevent some hangs during SPL.
[trini: Re-word commit message, make apply cleanly]
Signed-off-by: Tom Rini <trini@ti.com>
The functions to detect the state of the ready / busy signal is already
available but only used in the SPL case. Lets use it always, also for the
main U-Boot. As all boards should have this HW connection.
Testing on Siemens Draco (am335x) showed a small perfomance gain by using
this ready pin to detect the NAND chip state. Here the values tested on
Draco with Hynix 4GBit NAND:
Without NAND ready pin:
U-Boot# time nand read 80400000 0 400000
NAND read: device 0 offset 0x0, size 0x400000
4194304 bytes read: OK
time: 2.947 seconds, 2947 ticks
With NAND ready pin:
U-Boot# time nand read 80400000 0 400000
NAND read: device 0 offset 0x0, size 0x400000
4194304 bytes read: OK
time: 2.795 seconds, 2795 ticks
So an increase of approx. 5%.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Boards using the TWL4030 regulator may not all use the LDOs the same way
(e.g. MMC2 power can be controlled by another LDO than VMMC2).
This delegates TWL4030 MMC power initializations to board-specific functions,
that may still call twl4030_power_mmc_init for the default behavior.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Fix omap3_evm warning, add twl4030.h]
Signed-off-by: Tom Rini <trini@ti.com>
Renesas R-Mobile/R-Car ARM SoC of MMC has the same IP that are supported by
sh_mmcif. This adds support R-Mobile/R-Car ARM SoC with the setting of the
clock support.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Maximum value and the minimum value of clock for sh_mmcif instead by
base of MMC clock. This removes fixed clock, make the changes to be calculated
according to environment.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Use DIV_ROUND_UP and fls to simplify the code.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Not every device has multiple MMC slots available, so it makes sense to enable
only the required LDOs for the available slots. Generic code in omap_hsmmc will
enable both VMMC1 and VMMC2, in doubt.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
Some devices may use non-standard combinations of regulators to power MMC:
this allows these devices to provide a board-specific MMC power init function
to set everything up in their own way.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
just add a few ifdefs around because this
device is very similar to dra7xxx.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
there's no such function usb3_phy_power(),
it's likely that author meant to call,
usb_phy_power() instead, but that's already
called properly from xhci-omap.c.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
- fix crash when sata device is not initialized
- remove disable_sata_clock() since it is not clear which clock for which
device should be disabled here
- call disable_sata_clock() for mx6 in preboot_os instead
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Leave the OCOTP turned on, so that we subsequent access do not fail.
After enabling the thermal driver on a mx6sxsabresd board:
U-Boot 2015.01-rc1-18267-g99d4189-dirty (Nov 24 2014 - 12:59:01)
CPU: Freescale i.MX6SX rev1.0 at 792 MHz
CPU: Temperature 48 C
Reset cause: POR
Board: MX6SX SABRE SDB
I2C: ready
DRAM: 1 GiB
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
00:01.0 - 16c3:abcd - Bridge device
01:00.0 - 8086:08b1 - Network controller
In: serial
Out: serial
Err: serial
Net:
(hang)
As the thermal driver accesses the ocotp registers, its clock will be disabled
afterwards.
Then when the MAC address is read (also from ocotp registers) it will cause a
hang.
Do not disable the ocotp clock to prevent this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Printing the calibration data on every boot does not provide really useful
information:
U-Boot 2015.01-rc1-18266-ge7eb277 (Nov 24 2014 - 11:29:51)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
CPU: Thermal calibration data: 0x5d85067d
CPU: Temperature 33 C
Reset cause: POR
Board: MX6-SabreSD
Do not display the calibration data in order to have a cleaner boot log.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
A previous operation may have set the error flag, which must be cleared
before a new write operation can be issued.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The write operation may fail when trying to write to a locked area. In
this case the ERROR bit is set in the CTRL register. Check for that
condition and return an error.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
The code may goto 'fail' upon error with 'ret' variable set to an error
code, but this variable was being overwritten by a final preparation
function to restore the HCLK, so success was (in general) returned even
after an error was hit previously.
With this change, the function may now return success even if the final
preparation function fails, but it's probably enough to print a message
because (if successful) the real programming of the fuses has already
completed.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
If CONFIG_OF_CONTROL is defined, search device tree nodes that are
compatible with "panasonic,uniphier-ehci" and take the base address
from their "reg" property.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Marek Vasut <marex@denx.de>
This commit implements the ofdata_to_platdata handler for the UniPhier
serial driver and adds serial device nodes to the device tree sources.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The fdt_path_offset() checks an alias too.
fdtdec_get_alias_node(blob, "foo") is equivalent to
fdt_path_offset(blob, "foo").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Merge struct s3c2410_nand and struct s3c2440_nand into one unified
struct s3c24x0_nand. While at it, fix up and rename the functions
to retrieve the NAND base address and fix up the s3c NAND driver to
reflect this change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
This patch disables subpage writes for vf610_nfc nand
driver. This is required, as without this fix, writing
unaligned u-boot images with DFU results in a hang.
Trying to write unalgined binary images also results
in a hang, without disabling subpage writes.
Patch has been tested on a Colibri VF61 module.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Some but not all of implementations of the Denali NAND controller
have hardware circuits to detect the device parameters such as
page_size, erase_size, etc. Even on those SoCs with such hardware
supported, the hardware is known to detect wrong parameters for some
nasty (almost buggy) NAND devices. The device parameters detected
during nand_scan_ident() are more trustworthy.
This commit sets some hardware registers to mtd->pagesize,
mtd->oobsize, etc. in the code between nand_scan_ident() and
nand_scan_tail().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Chin Liang See <clsee@altera.com>
Some variants of the Denali NAND controller need some registers
set up based on the device information that has been detected during
nand_scan_ident().
CONFIG_SYS_NAND_SELF_INIT has to be defined to insert code between
nand_scan_ident() and nand_scan_tail(). It is also helpful to reduce
the difference between this driver and its Linux counterpart because
this driver was ported from Linux. Moreover, doc/README.nand recommends
to use CONFIG_SYS_NAND_SELF_INIT.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Chin Liang See <clsee@altera.com>
Commit ff94bc40af
("mtd, ubi, ubifs: resync with Linux-3.14")
accidentally reverted part of the commit
13f0fd94e3
("NAND: Scan bad blocks lazily.").
Reinstate the change as by commit
fb49454b1b
("nand: reinstate lazy bad block scanning")
Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
Acked-by: Heiko Schocher <hs@denx.de>
This is a rare event and should not happen. When it does it is confusing to
work out why. At least we should print a message.
Adjust the emulator to always print decode errors to the console.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there are DEBUG options spread around the place. If you enable
one and not another you can end up with an emulator that does not work,
since each file can have a different view of what the registers look like.
To fix this, create a global CONFIG_X86EMU_DEBUG option that keeps
everything consistent.
Signed-off-by: Simon Glass <sjg@chromium.org>
As well as locating the ROM on the PCI bus, allow the ROM to be supplied to
the emulator. Split the init up a little so that callers can supply their
own interrupt routines. Also allow a vesa mode to be provided, to be
selected once the BIOS run is complete.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is an implicit assumption that x86 machines want to use raw I/O in the
BIOS emulator, but this should be selectable. Add an CONFIG_X86EMU_RAW_IO
option to control it instead.
Also fix a few bugs which cause warnings on x86 and adjust the Makefile to
remove the assumption that only PowerPC uses the emulator.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a very simple driver which uses vesa to discover the video mode and
then provides a frame buffer for use by U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Some platforms don't have native code for dealing with their video
hardware. In some cases they use a binary blob to set it up and perform
required actions like setting the video mode. This approach is a hangover
from the old PC days where a ROM was provided and executed during startup.
Even now, these ROMs are supplied as a way to set up video. It avoids the
code for every video chip needing to be provided in the boot loader. But
it makes the video much less flexible - e.g. it is not possible to do
anything else while the video init is happening (including waiting hundreds
of milliseconds for display panels to start up).
In any case, to deal with this sad state of affairs, provide an API for
execution of x86 video ROMs, either natively or through emulation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some PCI functions cannot be auto-configured. Add a function to set up a
fixed BAR which can be used in these situations. Also add a function to read
the current address of a BAR.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add simplefb support, note this depends on the kernel having support for
the clocks property which has recently been added to the simplefb devicetree
binding.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Use pre-populated simplefb node under /chosen as
disussed on the devicetree list]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>.
Besided needing the usual sun6i specific ahb1_reset bits poking, it turns out
that sun6i also needs the drc to be taken out of reset and clocked even though
it is in pass-through mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
This adds a fixed mode hdmi driver for the sunxi platform. The fixed
mode is a relatively safe 1024x768, more complete EDID handling is
currently not provided. Only HDMI is supported today.
This code is enabled when HPD detects an attached monitor.
Current config is such that 8MB is shaved off at the top of the RAM.
This avoids several memory handling issues, most significant is the fact
that on linux on ARM you are not allowed to remap known RAM as IO. A
clued in display driver will be able to recycle this reserved RAM in
future though.
cfbconsole was chosen as it provides the most important functionality: a
working u-boot console, allowing for the debugging of certain issues
without the need for a UART.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Major cleanups and some small bugfixes]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Set TXFIFOTHRESH to adjust ddr pipeline delay for successful large
usb writes
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add reset_sata() to the sata driver interface and implement it
for dwc_ahsata. This function cleans up after sata_init(), and
therefore accepts a device number like sata_init() does.
A dummy implementation is provided for the rest of the drivers.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
The sandbox/ext4/fat/generic fs commands do not gracefully deal with files
greater than 2GB. Negative values are returned in such cases.
To handle this, the fs functions have been modified to take an additional
parameter of type "* loff_t" which is then populated. The return value
of the fs functions are used only for error conditions.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Update board/gdsys/p1022/controlcenterd-id.c,
drivers/fpga/zynqpl.c for changes]
Signed-off-by: Tom Rini <trini@ti.com>
When enumerating devices, honour the pci_skip_dev() function. This can
be used by PCI controller drivers to restrict which devices will be
probed.
This is required by the NVIDIA Tegra PCIe controller driver, which will
fail with a data abort exception if an access is attempted to a device
number larger than 0 outside of bus 0. pci_skip_dev() is therefore
implemented to prevent any such accesses.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Except the first loop, init_sata() should return 0 instead of 1
in the others.
This patch fix the issue of the 2nd sata port not workable on pci-sata card.
Signed-off-by: Pengbo Li <Pengbo.Li@freescale.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
These conditions never happen.
- There is no real uclass with UCLASS_INVALID id.
- uclass never becomes NULL because ll_entry_start() always returns
a valid pointer.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
The variable "drv" never becomes NULL because ll_entry_start()
always returns a valid pointer even if there are no entries.
The case "n_ents == 0" is covered by the following "for" loop.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
If the variable "ret" is equal to "-ENOENT", it is trapped at [1] and
never reaches [2]. At [3], the condition "ret != -ENOENT" is always
true.
if (ret == -ENOENT) { <------------------ [1]
continue;
} else if (ret == -ENODEV) {
dm_dbg("Device '%s' has no compatible string\n", name);
break;
} else if (ret) { <------------------ [2]
dm_warn("Device tree error at offset %d\n", offset);
if (!result || ret != -ENOENT) <------------------ [3]
result = ret;
break;
}
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
This fixes this cppcheck report:
[drivers/misc/cros_ec.c:704]: (error) Uninitialized variable: req
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Wolfgang Denk <wd@denx.de>
The SPI function does the same thing, so we may as well just use the new
generic function. The 'cs' parameter was not actually used, so can be
dropped.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
This code was not updated when the chip select handling was adjusted. Fix
it to call the correct function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
In some cases we need to manually bind a device to a particular driver.
Add a function to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Add dev_get_parent() as a convenience to obtain the parent of a device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
When the device is created from a device tree node, it matches a compatible
string. Allow access to that string and the associated data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
Move USB Errata checking code from "arch/powerpc" to architecture independent
file "fsl_usb.h" so that errata(s) become independent of the architecture.
For each erratum checking function for PPC arch, define a nop function for
non PPC arch for successful compilation in either case
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add a new thermal uclass for thermal sensor and implement the imx
thermal driver basing on this uclass.
Signed-off-by: Ye.Li <B37916@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Provide a CONFIG_DM_STDIO option to enable registering a serial device
with the stdio library. This is seldom useful in SPL, so disable it by
default when building for SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
For SPL we don't expect to need to remove a device. Save some code space
by dropping this feature. The board config can define
CONFIG_DM_DEVICE_REMOVE if this is in fact needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Add driver model support while retaining the existing legacy code. This
allows the driver to support boards that have converted to driver model
as well as those that have not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Before adding driver model support, split out a few of the functions so
that they can be used by the driver model code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Modify this driver to support driver model, with platform data required to
determine the GPIOs that it controls.
Signed-off-by: Simon Glass <sjg@chromium.org>
When not relying on Coreboot for GPIO init the GPIOs must be set up
correctly. This is currently done statically through a rather ugly method.
As the GPIOs are figured out they can be moved to the device tree and set
up as needed rather than all at the start.
In this implementation, board files should call ich_gpio_set_gpio_map()
before the GPIO driver is used in order to provide the GPIO information.
We use the early PCI interface so that this driver can now be used before
relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
For board IDs a common approach is to set aside several GPIOs for use in
determining the board ID. This can provide information about board features
and the revision.
Add a function that turns a list of GPIOs into an integer by assigning
each GPIO to a single bit.
Signed-off-by: Simon Glass <sjg@chromium.org>
In general we can't store things in the data section until we have inited
SDRAM. Some platforms allow this (e.g. those with SPL) but some don't. Move
the pointer to global_data so that it will work on all platforms.
Without this fix the serial port will not work prior to relocation with
driver model on some platforms.
Signed-off-by: Simon Glass <sjg@chromium.org>
U-Boot has imported various utility macros from Linux
scattering them to various places without consistency.
In include/common.h are min, max, min3, max3, ARRAY_SIZE, ALIGN,
container_of, DIV_ROUND_UP, etc.
In include/linux/compat.h are min_t, max_t, round_up, round_down,
etc.
We also have duplicated defines of min_t in some *.c files.
Moreover, we are suffering from too cluttered include/common.h.
This commit moves various macros that originate in
include/linux/kernel.h of Linux to their original position.
Note:
This commit simply moves the macros; the macros roundup,
min, max, min2, max3, ARRAY_SIZE are different
from those of Linux at this point.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The Linux-compatible macro DIV_ROUND_CLOSEST is a bit more flexible
and safer than DIV_ROUND.
For example,
foo = DIV_ROUND_CLOSEST(x, y++)
works expectedly, but
foo = DIV_ROUND(x, y++)
does not. (y is incremented twice.)
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
CONFIG_CPU_ARM920T was introduced into Kconfig by commit 2e07c249a6
(kconfig: arm: introduce symbol for ARM CPUs).
This commit removes all the defines of CONFIG_ARM920T and replaces the
only reference in drivers/usb/host/ohci-hcd.c with CONFIG_CPU_ARM920T.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The reset value of "uSDHCx_INT_STATUS_EN" register is changed to 0
on iMX6SX. So the fsl_esdhc driver must update to set the register,
otherwise no state can be detected.
Signed-off-by: Ye.Li <B37916@freescale.com>
for multi instance API we use struct fsl_esdhc_cfg to
pass the clock rate. Do not set f_max from global data,
since this is wrong for multi instance case.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As auto-negotiation is not supported for 2.5G SGMII, we need
to add a new type PHY_INTERFACE_MODE_SGMII_2500 to differentiate
SGMII-1G and SGMII-2.5G with different setting for auto-negotiation.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
According to EHCI specification, the LSB of DWORD 3 of Queue Head
(Current qTD Pointer) is not T-bit, but always zero.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
ls1021 is arm-core and support qe which is u-qe.
add u-qe init for arm board.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
[York Sun: Fix compiling error caused by u_qe_init()]
Reviewed-by: York Sun <yorksun@freescale.com>
The device id makes u-boot think that this chip needs
cfi_reverse_geometry(), which is not the case.
Add it to jedec_flash, so it is handled properly.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
ff94bc40af "mtd, ubi, ubifs: resync with Linux-3.14"
introduced the writebufsize field in struct mtd_info, which
is not initialized in the cfi_flash driver, which leads in
not working ubi on cfi flashes. Fix it
Signed-off-by: Heiko Schocher <hs@denx.de>
Reported-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
The User Register in GMAC IP is used to select interface type.
When with GE feature, it is used to select interface between
RGMII and GMII. If without GE feature, it is used to select
interface between MII and RMII.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
As in SAMA5D4 SoC, the gf table in ROM code can not be seen.
So, when we try to use PMECC, we need to build it when do
initialization.
Add a macro NO_GALOIS_TABLE_IN_ROM in soc header file. If it
is defined we will build gf table runtime.
The PMECC use the BCH algorithm, so based on the build_gf_tables()
function in lib/bch.c, we can build the Galois Field lookup table.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
device ready pin is signalling that the device is ready on state 1
not on 0. Simmiliar as it is in drivers/mtd/nand/nand_spl_simple.c
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
erase one nand block in spl code. keep it simple, as size matters
This is used on the upcoming taurus spl support.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
using this driver in SPL code with CONFIG_SPL_NAND_ECC
configured leads in an compileerror. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
[fix subject]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
move CONFIG_SYS_SPI_WRITE_TOUT into drivers/spi/atmel_spi.h
and define a default value. Delete this define in the board
config files, where it is possible (all boards use currently
the same value).
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
When boot up without mac address setting, it will give the warning
message like: "Warning: failed to set MAC address", however when
execute network related command, it still execute them without any
warning information.
With this patch, it will exit directly with following information:
"gmac0: mac address is not valid"
It also solve the problem after bootup then set mac address and the
mac address won't set to net device issue.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This change adds support for enabling the USB host features of the board.
This includes the USB3503A hub and the SMC LAN9730 ethernet controller
as well.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Allow to set the buck voltage for the max77686.
This will be used to reset the SMC LAN9730 ethernet on the odroids.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Recently the ext4 file system imposed passing absolute path with its file
name parameter.
As a result dfu_alt_info env variable has been modified to provide absolute
path when ext4 file system is accessed (e.g. /uImage ext4 0 2;).
Unfortunately, lthor flashing program provides plain file name (like uImage)
and hence those two file names do not match anymore.
Presented commit also allows lthor to write files to sub directories (like
/boot/bin/uImage).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Marek Vasut <marex@denx.de>
usb_phy_enable should return status bit, but not phy mode bit, thus
add a new function usb_phy_mode to query the PHY for it's mode and
make usb_phy_enable just return 0 but not 'phy_ctrl & USBPHY_CTRL_OTG_ID'.
Include a new board weak function board_usb_phy_mode. If board code
does not reimplement this function, it just call usb_phy_mode and return
usb_phy_mode's return value. The reason to include such a weak function
is: " SOC OTG core <--connect--> board HOST port, but no pin id for
the board host port, so board can not use usb_phy_mode to return the
phy mode, but define it's own rule."
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>
NEG bit default is '1' for external MDIOs as per FMAN-v3 RM, but on some
platforms, e.g. T2080QDS, this bit is '0', which leads to MDIO failure
on XAUI PHY, so set this bit definitely to align with the RM.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. use Payload length check disable when enable MAC;
2. add XGMII support for setting MAC interface mode;
3. only enable auto negotiation for Non-XGMII mode;
4. return 0xffff if clause 22 is used to read 10G phy_id;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-By: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for the 2 ehci controllers found on the sun6i (A31) soc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Marek Vasut <marex@denx.de>
Add proper Kconfig options to select the usb Vbus gpio-s, besides moving to
Kconfig being the right thing to do, an added advantage of this is that it
allows for boards without Vbus gpio-s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The A31 uses the AXP221 pmic for various voltages.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
--
Changes in v2:
-Rebase
Changes in v3:
-Add support for all dldo and aldo-s
-Add Kconfig option to select building AXP221 and to select voltage of
dldo and aldo-s
Changes in v4:
-Add axp221_setbits helper function
-Use symbolic names for enabled bits in CTRL1 - CTRL3 registers
Support EHCI host driver used on Panasonic UniPhier platform.
Since Device Tree is not supported on UniPhier yet, the base address
of USB cores are passed from board files (platdevice.c).
TODO for me:
Move the base address to device trees.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
The same bit-field macros are defined in include/linux/serial_reg.h
so let's include it and delete duplicated defines.
Also, remove unnecessary inclusion of <common.h>.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
In case of repeated START condition, the restart has to be kicked
before clear status (MSR register). If it is kicked after clear status,
R-Car I2C may transfer data (TXD register) or receive data (RXD register)
instead of transferring slave address (MAR register).
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Some slow I2C devices like Power Monitor(ZM7304) at times
do not work well with low timeout value, so I2C bus get stuck
during read cycle with this device, changing it to 100ms from
10ms works fine
A lot of other i2c drivers like mxc and i2c drivers of BOOTROM
also use relax timeouts to give sufficient ticks to work well
with slower devices
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
ppc4xx i2c master gets stuck on errors while repeated start is
active. Can be easily reproduced by "i2c md" on an unpopulated
i2c address. There is not stop condition given, scl remains
pulled low.
The only way out seems to be doing a stop manually and then a
soft reset.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Debugging some i2c trouble I saw on my scope that repeated
start is not working properply. The 4xx even held clock pulled down
after transfers. Having a look in the driver I realized
that IIC_CNTL_RPST is set on that part of the transfer that should
begin with a repeated start. But repeated start is about not sending a
stop condition, so IIC_CNTL_RPST has to be set on the last transfer
before the repeated start happens.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix error detected by cppcheck:
[drivers/net/uli526x.c:551]: (error) printf format string requires 3
parameters but only 2 are given.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Roy Zang <tie-fei.zang@freescale.com>
The pmic_spi_free function isn't ever used, and as the frameworks stand
today, cannot be, so remove it. Integrate the probe function into
pmic_reg as it's not really a "probe" today. Finally, add an err label
for the common failure cases.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Make sure to keep the MAC address programmed in the SMC911x ADDRH
and ADDRL registers. Linux can read those registers to determine
the MAC address on EEPROM-less configurations.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Tom Rini <trini@ti.com>
CMD_IAAD (Interrupt on Async Advance Doorbell) is bit 6, not bit 5.
While we are here, sort the flags.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Split the Samsung specific PHY control into a separate file
and compile this into the S3C OTG driver only if used on a
Samsung system.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Encapsulate the Samsung PHY control and its register accesses
into the otg_phy_init() and otg_phy_off() functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Remove the useless inclusion of arch/arm/gpio.h , which is completely
bogus in this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Switch the default CD GPIO polarity to active low.
The current hsmmc driver assumption that the CD GPIO is active high, but
in the real hardware, usually the opposite holds.
The usual SD card socket has a mechanical switch which is grounded as
soon as a card is inserted.
Of course there might be some board logic which inverts the signal, but
as far as current users are concerned, there is no such logic.
Current U-Boot users either not using the CD functionality, or have a
different way (e.g. external to SoC GPIO controller) for checking the
card presence.
This patch also brings the polarity assumption in line with the Linux
kernel and adds appropriate comments.
This patch also might spare issues once the TWL GPIO driver will be
converted to the DM.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
The verification qm_cfg existence is done at ksnav_init().
So, there is no need to verify it after initialization.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
As per Marvell Release Notes - Alaska 88E1510/88E1518/88E1512/88E1514
Rev A0, Errata Section 3.1 Marvell PHY has an errata which requires
that certain registers get written in order to restart
autonegotiation.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Keystone2 Lamar SoC uses the same keystone net driver.
This patch adds opportunity to use it by K2L SoCs.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Keystone2 Lamar SoC uses the same keystone SerDes driver.
All Keystone2 EVM boards currently use SerDes driver, so move
CONFIG_TI_KEYSTONE_SERDES to common configuration file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This is necessary for the device-model enabled builds to work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is necessary for the device-model enabled builds to work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a driver for the designware serial UART used on sunxi. This just
redirects to the normal ns16550 driver.
Add a stdout-path to the device tree so that the correct UART is chosen.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This adds driver model support to the sunxi GPIO driver, using the device
tree to trigger binding of the driver. The driver will still operate
without driver model too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Mostly automatic with:
sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I)
followed by removing the relevant #defines from include/configs/sun?i.h by
hand.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
R8A7791, R8A7793 and R8A7794 have same IP of USB controller.
This collect up address data of each SoCs.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
R8A7793 has same IP of USB controller as R8A7791 and R8A7794 of rmobile
ARM SoCs. This adds support R8A7793 to EHCI HCD of rmobile.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
A bit field of DMA descriptor is on memory area of DMA. If we set data
to bit of DMA descriptor, we must be writeback data of DMA descriptor.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
RX_DESC_SIZE and TX_DESC_SIZE mean the size of the data descriptor for sh-eth.
We can acquire this in sizeof. It is not necessary to define these in define.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
R8A7793 has the same sh-ether IP core as other SH/rmobile.
This patch adds support of R8A7793.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This adds the preset value to register for R8A7793.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This enables the VMMC2 LDO, which powers the MMC2 device.
When the device starts from MMC2, this has already been enabled by the BootROM,
but when starting from peripheral boot (USB, UART), it is not the case.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
With enabled framebuffer console the printenv command can take several
seconds to complete. This patch temporarily disables cache flush when
writing strings to fb console. Then there is no noticable delay anymore.
Tested with imx6 hdmi framebuffer.
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Add ECC geometry for NAND which has 2048b pagesize and 112b OOB
size. This is for example Macronix MX30LF2G28AB chip.
Signed-off-by: Marek Vasut <marex@denx.de>
In preparation for the SoCFPGA support of the designware I2C driver,
convert this driver to the common CONFIG_SYS_I2C framework.
This patch converts all users of this driver, this is:
- ST spearxxx boards
- AXS101 (ARC700 platform)
I couldn't test this patch on those boards. Only compile tested for all
spear boards. And tested on SoCFPGA.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
This patch permeates the struct i2c_adapter throughout the driver,
so that it can be used to determine which adapter should be used.
Note that the driver still supports only one adapter. Note that
the patch does shuffle mxs_i2c_set_bus_speed() to the top of the
driver, but the function remains unchanged.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This patch just converts the function prototypes used throughout
this driver to match those of the i2c framework. There is so far
no functional change. This patch does not do the deeper integration
of the framework bits.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This patch prepares the MXS I2C driver for the conversion to the
new I2C driver framework by pulling out the hard-coded I2C0 address
from all the places.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
The logic of the return statement in sata_port_status() calls for a
bitwise 'AND' operator, not logical 'AND'. Fix the typo.
Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
The SD Card slot detection pin should be configured as input.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
I finally had a look at the datasheet and spotted an additional
register address difference between regular E1000 and i210/i211 chips.
This patch fixes this and now successfully works on programmed
i210/i211 as well as unprogrammed i211.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Commit 951860634f may have changed
the logic unintentially from "if (!(swfw_sync & (fwmask | swmask)))"
to "if ((swfw_sync & swmask) && !(swfw_sync & fwmask))". This change
breaks some e1000 NIC with a message "ERROR: Unable to read EEPROM!".
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Marek Vasut <marex@denx.de>
CC: Tim Harvey <tharvey@gateworks.com>
Acked-by: Marcel Ziswiler <marcel@ziswiler.com>
it is not correct to init for a specific slave in spi_setup_slave.
instead buffer the values and delay init until spi_claim_bus.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
the second reset prevents other registers to be written.
This will prevent to have the correct signal levels for
SCLK before writing to the config reg in spi_xchg_single.
Tested with GPIO based chipselect and SPI_MODE_3 on i.MX6S
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Just move the configuration options scattered all over the driver
to the top of the source file. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
The variable d is used in rather questionable way. Rework the code
a bit so it's clearer what it does. Also, rename the variable from
d to data to make it's name less mysterious. Finally, change it's
data type to uint32_t , since it's accessed as a 32bit number.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
The driver contained an endless loop when waiting for TX completion,
this is a bad idea since if the hardware fails, the loop might spin
forever. Add timeout and handle it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This patch just zaps most of the checkpatch cries present in the
driver. There is one more left, which will be addressed separately.
There is no functional change.
This patch also adds a bunch of newlines all around the place, this
is to make the code much more readable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Clean up the definitions of bits in the Altera SPI driver, there
is no need to put braces around numbers afterall. No functional
change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Zap the offset-based register access and use the struct-based one
as this is the preferred method.
No functional change, but there are some line-over-80 problems in
the driver, which will be addressed later.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
The file board/Marvell/include/mv_gen_reg.h is incompatible with
the GPL (see for example the "MARVELL RESERVES THE RIGHT AT ITS SOLE
DISCRETION TO REQUEST THAT THIS CODE BE IMMEDIATELY RETURNED TO
MARVELL" clause). As this cannot be fixed, we remove the file and all
code that depends on it. Fortunately this only affects some very old
boards that have long reached EOL:
CPCI750
DB64360
DB64460
p3m750
p3m7448
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Include the i2c header and change the non confirming
functions to do so.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Heiko Schocher <hs@denx.de>
[trini: Fix i2c_get_bus_num prototype]
Signed-off-by: Tom Rini <trini@ti.com>
- make omap_spl_dev_ready static
- make omap_reverse_list static, move to under CONFIG_NAND_OMAP_ELM
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Tom Rini <trini@ti.com>
get_phy_id is marked weak but has no protype nor a
strong version, just make it static. Use __weak for
board_phy_config.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
For various reasons (design, errata) boards may need to implement their
own versions of these accessors. So in the case of
CONFIG_CFI_FLASH_USE_WEAK_ACCESSOR mark the functions as weak. In the
normal case mark them as static to allow for better optimization.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
[trini: Reword commit message]
Signed-off-by: Tom Rini <trini@ti.com>
The Allwinner A23 SoC has reset controls like the A31 (sun6i).
The FIFO address is also the same as sun6i.
Re-use code added for sun6i.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
sunxi SOCs can boot from both mmc0 and mmc2, detect from which one we're
booting, and make that one "mmc dev 0" so that a single u-boot binary can
be used for both the onboard eMMC and for external sdcards.
When we're booting from mmc2, we make it dev 0 because that is where the SPL
will load the tertiary payload (the actual u-boot binary in our case) from,
see: common/spl/spl_mmc.c, which has dev 0 hardcoded everywhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The mmc hardware on sun6i has an extra reset control that needs to
be de-asserted prior to usage. Also the FIFO address is different.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: use setbits_le32 for reset control, drop obsolete changes,
rewrite different FIFO address handling, add commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Allwinner A20/A23/A31's SD/MMC host support SDHC High Capacity feature.
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The UniPhier serial driver has been converted to driver model.
Let's remove uniphier_serial_initialize() call from the old
serial driver framework.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit converts UniPhier on-chip serial driver to driver model.
Since UniPhier SoCs do not have Device Tree support, some board files
should be added under arch/arm/cpu/armv7/uniphier/ph1-*/ directories.
(Device Tree support for UniPhier platform is still under way.)
Now the base address and master clock frequency are passed from
platform data, so CONFIG_SYS_UNIPHIER_SERIAL_BASE* and
CONFIG_SYS_UNIPHIER_UART_CLK should be removed.
Tested on UniPhier PH1-LD4 ref board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
