uninitialized retval variable warning fixed
crc32 APIs moved to crc.h (newly added) and build warnings fixed
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
The number of CPUs are getting detected dynamically by checking the
processor SVR value. Also removed CONFIG_NUM_CPUS references from all
the platforms with 85xx/86xx processors.
This can help to use the same u-boot image across the platforms.
Also revamped and corrected few Freescale Copyright messages.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The reordering of include/common.h by commit fcd3c87e49 broke
boards with status LED support, resulting in
error: #error Status LED configuration missing
errors. Undo this reordering to avoid this issue.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 70ebf316 factored out the ROUND() macro into include/common.h,
not realizing that the primary use of this macro on AT91 systems was
in start.S where common.h was not included, and could not be included
because it contains a lot of C code which the assembler doesn't
understand.
This patch wraps such code in common.h in a "#ifndef __ASSEMBLY__"
construct, and then adds an include to cpu/arm926ejs/start.S thus
solving the problem.
Signed-off-by: Wolfgang Denk <wd@denx.de>
A large number of boards (all AT91 based) duplicated the ROUND()
macro in their board specific config files. Add the definition to
include/common.h and clean up the board config files.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Use the standard lowercase "xx" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Move needed definitions (register descriptions etc.) from
include/mpc512x.h into include/asm-ppc/immap_512x.h.
Instead of using a #define'd register offset, use a function that
provides the PATA controller's base address.
All the rest of include/mpc512x.h are register offset definitions
which can be eliminated by proper use of C structures.
There are only a few register offsets remaining that are needed in
cpu/mpc512x/start.S; for these we provide cpu/mpc512x/asm-offsets.h
which is intended as a temporary workaround only. In a later patch
this file will be removed, too, and then auto-generated from the
respective C structs.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
The kernel stores address<->symbol names in it so things can be decoded at
runtime. Do it in U-Boot, and we get nice symbol decoding when crashing.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
introduce serial_exit for this purpose. Use it only when the rm9200
serial driver is active
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
According to the doc/feature-removal-schedule.txt, the "autoscr"
command will be replaced by the "source" command in approximately 6
months from now.
This patch prepares this change and starts a 6 month transition
period as follows:
- The new "source" command has been added, which implements exactly
the same functionlaity as the old "autoscr" command before
- The old "autoscr" command name is kept as an alias for compatibility
- Command sequences, script files atc. have been adapted to use the
new "source" command
- Related environment variables ("autoscript", "autoscript_uname")
have *not* been adapted yet; these will be renamed resp. removed in
a separate patch when the support for the "autoscr" command get's
finally dropped.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
Rather than have common ppc code call a board-specific function like
load_sernum_ethaddr(), have each board call it in its own board-specific
misc_init_r() function.
The boards that get converted here are:
- kup4k/kup4x
- pcs440ep
- tqm8xx
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Stefan Roese <sr@denx.de>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
Rather than have the common ppc code have board-specific hooks, move the
board_get_enetaddr() function into the board-specific init functions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
NetLoop polls every cycle with getenv some environment variables.
This is horribly slow, especially when the environment is big.
This patch reads only the environment variables in NetLoop,
when they were changed.
Also moved the init part of the NetLoop function in a seperate
function.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds flush_/invalidate_dcache_range() to the MIPS architecture.
Those functions are needed for the upcoming dcache support for the USB
EHCI driver. I chose this API because those cache handling functions are
already present in the PPC architecture.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Modifications to support console multiplexing. This is controlled using
CONFIG_SYS_CONSOLE_MUX in the board configuration file.
This allows a user to specify multiple console devices in the environment
with a command like this: setenv stdin serial,nc. As a result, the user can
enter text on both the serial and netconsole interfaces.
All devices - stdin, stdout and stderr - can be set in this manner.
1) common/iomux.c and include/iomux.h contain the environment setting
implementation.
2) doc/README.iomux contains a somewhat more detailed description.
3) The implementation in (1) is called from common/cmd_nvedit.c to
handle setenv and from common/console.c to handle initialization of
input/output devices at boot time.
4) common/console.c also contains the code needed to poll multiple console
devices for input and send output to all devices registered for output.
5) include/common.h includes iomux.h and common/Makefile generates iomux.o
when CONFIG_SYS_CONSOLE_MUX is set.
Signed-off-by: Gary Jennejohn <garyj@denx.de>
Round clock frequencies for printing.
Many boards printed off clock frequencies like 399 MHz instead of the
exact 400 MHz because numberes were not rounded. This is fixed now.
Signed-off-by: Wolfgang Denk <wd@denx.de>
ARM, i386, m68k and ppc all have identical implementations of strmhz().
Other architectures don't provide this function at all.
This patch moves strmhz() into lib_generic, reducing code duplication
and providing a more unified API across architectures.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.
This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.
MAKEALL ppc/arm has some issues:
* DOC/OneNand/nand_spl is not building (I have not tried porting
these parts, and since I do not have any HW and I am not familiar
with this code/HW I think its best left to someone else.)
Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
cpu/ppc4xx/ndfc.c
cpu/arm926ejs/davinci/nand.c
board/delta/nand.c
board/zylonite/nand.c
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The compiler will help find mismatches between printf formats and
arguments if you let it. This patch adds the necessary attributes to
declarations in include/common.h, then begins to correct the resulting
compiler warnings. Some of these were bugs, e.g., "$d" instead of
"%d" and incorrect arguments. Others were just annoying, like
int-long mismatches on a system where both are 32 bits. It's worth
fixing the annoying errors to catch the real ones.
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
ALIGN() returns the smallest aligned value greater than the passed
in address or size. Taken from Linux.
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory. phys_size_t is defined as an unsigned long on almost
all current platforms.
This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram). It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.
Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
AVR32 and AT91SAM9 both have their own identical definitions of
container_of() taken from the Linux kernel. Move it to common.h so
that all architectures can use it.
container_of() is already used by some drivers, and will be used
extensively by the new and improved SPI API.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Implement watchodg-aware variants of hash calculation functions:
- crc32_wd()
- md5_wd()
- sha1_csum_wd()
The above functions calculate the hash of the input buffer in chunks,
triggering the watchdog after processing each chunk. The chunk size
is given as a function call parameter.
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
in commit fad634071 "make show_boot_progress () weak."
show_boot_progress is supposed to be declared as weak but declared as
inline instead.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
eg. because of rounding error we can get 799Mhz instead of 800Mhz.
Introduced DIV_ROUND_UP and roundup taken from linux kernel.
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
The envcrc.c does sizeof(unsigned long) when calculating the crc, but
this is done with the build toolchain instead of the target tool
chain, so if the build is a 64bit system but the target is 32bits,
the size will obviously be wrong. This converts all unsigned long
stuff related to crc32 to uint32_t types. Compile tested only: output
of ./tools/envcrc when run on a 32bit build system matches that of a
64bit build system.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Introduce the new logical option CONFIG_HAS_POST which is set when the
platform has CONFIG_POST set. Use CONFIG_HAS_POST in the post/ Makefiles
to determine should the POST libs be compiled for the selected target
platform, or not.
To avoid breaking u-boot linking process, the empty post/libpost.a file is
created for platforms which do not have POSTs.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
The following changes are needed to be inline with ePAPR v0.81:
* r4, r5 and now always set to 0 on boot release
* r7 is used to pass the size of the initial map area (IMA)
* EPAPR_MAGIC value changed for book-e processors
* changes in the spin table layout
* spin table supports a 64-bit physical release address
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added the cpu command that provides a generic mechanism to get status,
reset, and release secondary cores in multicore processors.
Added support for using the ePAPR defined spin-table mechanism on 85xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
autoscript() routine is updated to accept second argument, which
is only used for FIT images and provides a FIT subimage unit name.
autoscript() routine callers must now pass two arguments. For
non-interactive use (like in cmd_load.c, cmd_net.c), new environment
variable 'autoscript_uname' is introduced and used as a FIT
subimage unit name source.
autoscript command accepts extended syntax of the addr argument:
addr:<subimg_uname>
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
This patch adds a IRQ demultiplexer callback to the arm920 cpu core code,
plus a stub implementation of it for the S3C2410.
The purpose is to allow arm920t implementations such as the s3c24x0 to
implement interrupt handlers in u-boot without having to touch core
arm920t code.
Signed-off-by: Harald Welte <laforge@openmoko.org>
Add new function readline_into_buffer() that allows the
output of readline to be put into a pointer to char buffer.
This refactoring allows other functions besides the
main command loop to also use the same input mechanism.
Signed-off-by: James Yang <James.Yang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
This is an API for external (standalone) applications running on top of
U-Boot, and is meant to be more extensible and robust than the existing
jumptable mechanism. It is similar to UNIX syscall approach. See api/README
for more details.
Included is the demo application using this new framework (api_examples).
Please note this is still an experimental feature, and is turned off by
default.
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
The MPC8572 introduces the concept of an asynchronous DDR clock with
regards to the platform clock.
Introduce get_ddr_freq() to report the DDR freq regardless of sync/async
mode.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Till now the UTL registers on 405EX were not initialized but left with
their default values. This patch new initializes some of the UTL
registers on 405EX.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves some common 4xx macros and the PPC405_SYS_INFO/
PPC440_SYS_INFO structure into the common ppc4xx.h header.
Lot's of other macros are good candidates to be consolidated this way
in the future.
Signed-off-by: Stefan Roese <sr@denx.de>
- correct configuration space mapping
- correct bus numbering
- better access to config space
Prior to this patch, the 440SPe host/PCIe bridge was able to configure only the
first device on the first bus. We now allow to configure up to 16 buses;
also, scanning for devices behind the PCIe-PCIe bridge is supported, so
peripheral devices farther in hierarchy can be identified.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Add support for the following DaVinci boards:
- DV_EVM
- SCHMOOGIE
- SONATA
Changes:
- Split into separate board directories
- Removed changes to MTD_DEBUG (or whatever it's called)
- New CONFIG_CMD party line followed
- Some cosmetic fixes, cleanup etc.
- Patches against the latest U-Boot tree as of now.
- Fixed CONFIG_CMD_NET in net files.
- Fixed CONFIG_CMD_EEPROM for schmoogie.
- Made sure it compiles and works (forceenv() link problem) on SCHMOOGIE and
DV_EVM. Can't check if it works on SONATA, don't have a board any more,
but it at least compiles.
Here is an excerpt from session log on SCHMOOGIE...
U-Boot 1.2.0-g6c33c785-dirty (Aug 7 2007 - 13:07:17)
DRAM: 128 MB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
ARM Clock : 297MHz
DDR Clock : 162MHz
ETH PHY : DP83848 @ 0x01
U-Boot > iprobe
Valid chip addresses: 1B 38 3A 3D 3F 50 5D 6F
U-Boot > ping 192.168.253.10
host 192.168.253.10 is alive
U-Boot >
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Zach Sadecki <Zach.Sadecki@ripcode.com>
Acked-by: Stefan Roese <sr@denx.de>
83xx processor family has many reset sources, such as
power on reset, software hard reset, software soft reset,
JTAG, bus monitor, software watchdog, check stop reset,
external hard reset, external software reset.
sometimes, to figure out the fault of system, we need to
know the cause of reset early before the prompt of
u-boot present.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch removes the CFG_PCI_PRE_INIT option completely, since
it's not needed anymore with the patch from Matthias Fuchs with
the "weak" pci_pre_init() implementation.
Signed-off-by: Stefan Roese <sr@denx.de>
Printing a buffer is a darn useful thing. Move the buffer print code
into print_buffer() in lib_generic/
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The 834x rev1.x silicon has one CPU5 errata.
The issue is when the data cache locked with
HID0[DLOCK], the dcbz instruction looks like no-op inst.
The right behavior of the data cache is when the data cache
Locked with HID0[DLOCK], the dcbz instruction allocates
new tags in cache.
The 834x rev3.0 and later and 8360 have not this bug inside.
So, when 834x rev3.0/8360 are working with ECC, the dcbz
instruction will corrupt the stack in cache, the processor will
checkstop reset.
However, the 834x rev1.x can work with ECC with these code,
because the sillicon has this cache bug. The dcbz will not
corrupt the stack in cache.
Really, it is the fault code running on fault sillicon.
This patch fix the incorrect dcbz operation. Instead of
CPU FP writing to initialise the ECC.
CHANGELOG:
* Fix the incorrect dcbz operation instead of CPU FP
writing to initialise the ECC memory. Otherwise, it
will corrupt the stack in cache, The processor will checkstop
reset.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Added code for reading and writing Mac addresses to/from ID EEPROM(0x57).
With attached patch, we can use command "mac/mac read/mac save/"
to read and write EEPROM under u-boot prompt.
U-boot will calculate the checksum of EEPROM while bootup,
if it is right, then u-boot will check whether the mac address
of eTSEC0/1/2/3 is availalbe (non-zero).
If there is mac address availabe in EEPROM, u-boot will use it,
otherewise, u-boot will use the mac address defined in
MPC8641HPCN.h. This matches the requirement to set unique mac address
for each TSEC port.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Second serial port on 440GX now defined as a system device.
Add 'Short Etch' code for Cicada PHY within 440gx_enet.c
Patch by Travis B. Sawyer, 12 Jul 2005
Check return value of malloc in 440gx_enet.c
Patch by Travis B. Sawyer, 18 Jul 2005
- remove all references to CONFIG_INIT_CRITICAL for ARM based boards
- introduce two new configuration options instead:
CONFIG_SKIP_LOWLEVEL_INIT and CONFIG_SKIP_RELOCATE_UBOOT
* Patch by Sascha Hauer, 28 Jun:
- add generic support for Motorola i.MX architecture
- add support for mx1ads, mx1fs2 and scb9328 boards
* Patches by Marc Leeman, 23 Jul 2004:
- Add define for the PCI/Memory Buffer Configuration Register
- corrected comments in cpu/mpc824x/cpu_init.c
* Add support for multiple serial interfaces
(for example to allow modem dial-in / dial-out)
Completion of the 8540ADS/8560ADS updates:
Fix some PCI and Rapid I/O memory maps,
Initialize both TSEC 1 and 2,
Initialize SDRAM
Update MAINTAINER for 85xx boards and README.mpc85xxads
- Make MPC5200 boards evaluate the SVR to print processor name and
version in checkcpu() (cpu/mpc5xxx/cpu.c).
* Patch by Kai-Uwe Bloem, 06 May 2004:
Fix endianess problem in cramfs code
- Add support for the Logic Zoom LH7A40x based SDK board(s),
specifically the LPD7A400.
* Patches by Robert Schwebel, 15 May 2004:
- call MAC address reading code also for SMSC91C111;
- make SMSC91C111 timeout configurable, remove duplicate code
- fix get_timer() for PXA
- update doc/README.JFFS2
- use "bootfile" env variable also for jffs2
- Rename DUET_ADS to MPC885ADS
- Rename CONFIG_DUET to CONFIG_MPC885_FAMILY
- Rename CONFIG_866_et_al to CONFIG_MPC866_FAMILY
- Clean up FADS family port to use the new defines
- add auto-complete support to the U-Boot CLI
- add support for NETTA and NETPHONE boards; fix NETVIA board
* Patch by Yuli Barcohen, 28 Mar 2004:
- Add support for MPC8272 family including MPC8247/8248/8271/8272
- Add support for MPC8272ADS evaluation board (another flavour of MPC8260ADS)
- Change configuration method for MPC8260ADS family
- Unify video mode handling for Chips & Technologies 69000 Video
chip and Silicon Motion SMI 712/710/810 Video chip
- Add selection of the video output (CRT or LCD) via 'videoout'
environment variable for the Silicon Motion
- README update
* Patch by Pierre Aubert, 18 Mar 2004:
include/common.h typo fix
* Patches by Tolunay Orkun, 17 Mar 2004:
- Add support for bd->bi_iic_fast[] initialization via environment
variable "i2cfast" (CONFIG_I2CFAST)
- Add "i2cfast" u-boot environment variable support for csb272
- Added LBA48 support (CONFIG_LBA48 & CFG_64BIT_LBA)
- Added support for 64bit printing in vsprintf (CFG_64BIT_VSPRINTF)
- Added support for 64bit strtoul (CFG_64BIT_STRTOUL)
* Patch by Masami Komiya, 27 Feb 2004:
Fix rarpboot: add autoload by NFS
* Patch by Dan Eisenhut, 26 Feb 2004:
fix flash_write return value in saveenv
* Patch by Stephan Linz, 11 Dec 2003
expand config.mk to avoid trigraph warnings on NIOS
* Rename "BMS2003" board into "HMI10"
Add support for IBM PPC440GX. Multiple EMAC Ethernet devices,
select MDI port based on enabled EMAC device.
Add support for XES Inc <http://www.xes-inc.com> XPedite1000 440GX
base PrPMC board.
see doc/README.MPC866 for details;
implement workaround for "SIU4" and "SIU9" silicon bugs on MPC866;
calculate CPU clock frequency from PLL register values.
* Add support for 128 MB RAM on TQM8xxL/M modules
before we can access it; add delay in case we are faster (with no
CF card inserted)
* Cleanup of some init functions
* Make sure SCC Ethernet is always stopped by the time we boot Linux
to avoid Linux crashes by early packets coming in.
* Accelerate flash accesses on LWMON board by using buffered writes
* Patch by Scott McNutt, 02 Jan 2004:
Add support for the Nios Active Serial Memory Interface (ASMI)
on Cyclone devices
* Patch by Andrea Marson, 16 Dec 2003:
Add support for the PPChameleon ME and HI modules
* Patch by Yuli Barcohen, 22 Dec 2003:
Add support for Motorola DUET ADS board (MPC87x/88x)
- add support for the PATI board (MPC555)
- add SPI support for the MPC5xx
* Patch by Anders Larsen, 08 Dec 2003:
add configuration options CONFIG_SERIAL_TAG and CONFIG_REVISION_TAG
to pass ATAG_SERIAL and ATAG_REVISION, resp., to the ARM target;
cleanup some redundand #defines
* Minor code cleanup (coding style)
* Patch by Reinhard Meyer, 30 Dec 2003:
- cpu/mpc5xxx/fec.c: added CONFIG_PHY_ADDR, added CONFIG_PHY_TYPE,
- added CONFIG_PHY_ADDR to include/configs/IceCube.h,
- turned debug print of PHY registers into a function (called in two places)
- added support for EMK MPC5200 based modules
* Fix MPC8xx PLPRCR_MFD_SHIFT typo
* Add support for TQM866M modules
* Fixes for TQM855M with 4 MB flash (Am29DL163 = _no_ mirror bit flash)
* Fix a few compiler warnings
environment variable which can set to "100", "133", or "150". The
CPU clock will be configured accordingly upon next reboot. Other
values are ignored. In case of an invalid or undefined "cpuclk"
value, the compile-time default CPU clock speed will be used.
* Enable Quad-UART on BMS2003 board (initialize the PCMCIA memory
window that is used to access the UART registers by the Linux driver)
* Patch by Reinhard Meyer, 20 Dec 2003:
Fix clock calculation for the MPC5200 for higher clock frequencies
(above 2**32 / 10 = 429.5 MHz).
- Added Motorola CPU 8540/8560 support (cpu/85xx)
- Added Motorola MPC8540ADS board support (board/mpc8540ads)
- Added Motorola MPC8560ADS board support (board/mpc8560ads)
* Minor code cleanup
- fix cmd_ide.c for non ppc boards (read/write functions did not
add ATA base address)
- fix for shannon board
- #ifdef CONFIG_IDE_8xx_DIRECT some otherwise unused code
* Patch by Sangmoon Kim, 07 Oct 2003:
add support for debris board
applications: instead of using (PPC-specific) system calls we now
use a jump table; please see doc/README.standalone for details
* Patch by Dave Westwood, 24 Jul 2003:
added support for Unity OS (a proprietary OS)
add delay to get I2C working with "imm" command and s3c24x0_i2c.c
* Patch by Richard Woodruff, 17 July 03:
- Fixed bug in OMAP1510 baud rate divisor settings.
* Patch by Nye Liu, 16 July 2003:
MPC860FADS fixes:
- add MPC86xADS support (uses MPC86xADS.h)
- add 866P/T core support (also MPC859T/MPC859DSL/MPC852T)
o PLPRCR changes
o BRG changes (EXTAL/XTAL restricted to 10MHz)
o don't trust gclk() software measurement by default, depend on
CONFIG_8xx_GCLK_FREQ
- add DRAM SIMM not installed detection
- use more "correct" SDRAM initialization sequence
- allow different SDRAM sizes (8xxADS has 8M)
- default DER is 0
- remove unused MAMR defines from FADS860T.h (all done in fads.c)
- rename MAMR/MBMR defines to be more consistent. Should eventually
be merged into MxMR to better reflect the PowerQUICC datasheet.
* Patch by Yuli Barcohen, 16 Jul 2003:
support new Motorola PQ2FADS-ZU evaluation board which replaced
MPC8260ADS and MPC8266ADS
- remove trailing white space, trailing empty lines, C++ comments, etc.
- split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c)
* Patches by Kenneth Johansson, 25 Jun 2003:
- major rework of command structure
(work done mostly by Michal Cendrowski and Joakim Kristiansen)
- Hymod board database mods: add "who" field and new xilinx chip types
- provide new "init_cmd_timeout()" function so code external to
"common/main.c" can use the "reset_cmd_timeout()" function before
entering the main loop
- add DTT support for adm1021 (new file dtt/adm1021.c; config
slightly different. see include/configs/hymod.h for an example
(requires CONFIG_DTT_ADM1021, CONFIG_DTT_SENSORS, and
CFG_DTT_ADM1021 defined)
- add new "eeprom_probe()" function which has similar args and
behaves in a similar way to "eeprom_read()" etc.
- add 8260 FCC ethernet loopback code (new "eth_loopback_test()"
function which is enabled by defining CONFIG_ETHER_LOOPBACK_TEST)
- gdbtools copyright update
- ensure that set_msr() executes the "sync" and "isync" instructions
after the "mtmsr" instruction in cpu/mpc8260/interrupts.c
- 8260 I/O ports fix: Open Drain should be set last when configuring
- add SIU IRQ defines for 8260
- allow LDSCRIPT override and OBJCFLAGS initialization: change to
config.mk to allow board configurations to override the GNU
linker script, selected via the LDSCRIPT, make variable, and to
give an initial value to the OBJCFLAGS make variable
- 8260 i2c enhancement:
o correctly extends the timeout depending on the size of all
queued messages for both transmit and receive
o will not continue with receive if transmit times out
o ensures that the error callback is done for all queued tx
and rx messages
o correctly detects both tx and rx timeouts, only delivers one to
the callback, and does not overwrite an earlier error
o logic in i2c_probe now correct
- add "vprintf()" function so that "panic()" function can be
technically correct
- many Hymod board changes
* Patches by Kyle Harris, 13 Mar 2003:
- Add FAT partition support
- Add command support for FAT
- Add command support for MMC
----
- Add Intel PXA support for video
- Add Intel PXA support for MMC
----
- Enable MMC and FAT for lubbock board
- Other misc changes for lubbock board
instead CFG_MONITOR_LEN is now only used to determine _at_compile_
_time_ (!) if the environment is embedded within the U-Boot image,
or in a separate flash sector.
* Cleanup CFG_DER #defines in config files (wd maintained only)
* Patch by Keith Outwater, 28 Apr 2003:
- Miscellaneous corrections and additions to GEN860T board specific code.
- Added GEN860_SC variant to GEN860T.
- Miscellaneous corrections to GEN860T documentation.
- Correct duplicate entry in U-Boot CREDITS file.
- Add GEN860T_SC entry in MAINTAINERS file.
- Update CREDITS file with GEN860T_SC info.
* Update Smiths Aerospace addresses in MAINTAINERS file
* Fix error handling in hush's version of "run" command
- Add port to MPC555/556 microcontrollers
- Add support for cmi customer board with
Intel 28F128J3A, 28F320J3A or 28F640J3A flash.
* Patch by Rick Bronson, 28 Mar 2003:
- fix common/cmd_nand.c
- 16/32 MB and 50/80 MHz support with auto-detection for IP860
- ETH05 and BEDBUG support for CU824
- added support for MicroSys CPC45
- new BOOTROM/FLASH0 and DOC base for PM826
* Patch by Robert Schwebel, 12 Mar 2003:
Fix the chpart command on innokom board
* Name cleanup:
mv include/asm-i386/ppcboot-i386.h include/asm-i386/u-boot-i386.h
s/PPCBoot/U-Boot/ in some files
s/pImage/uImage/ in some files
* Patch by Detlev Zundel, 15 Jan 2003:
Fix '' command line quoting
* Patch by The LEOX team, 19 Jan 2003:
- add support for the ELPT860 board
- add support for Dallas ds164x RTC
* Patch by Erwin Rol, 27 Feb 2003:
Add support for RTEMS
* Add image information to README
* Fix dual PCMCIA slot support (when running with just one
slot populated)
* Add VFD type detection to trab board
* extend drivers/cs8900.c driver to synchronize ethaddr environment
variable with value in the EEPROM
* Start adding MIPS support files
Add code for AmigaOne board
(preliminary merge to U-Boot, still WIP)
* Patch by Jon Diekema, 12 Nov 2002:
- Adding URL for IEEE OUI lookup
- Making the autoboot #defines dependent on CONFIG_AUTOBOOT_KEYED
being defined.
- In the CONFIG_EXTRA_ENV_SETTINGS #define, the root-on-initrd and
root-on-nfs macros are designed to switch how the default boot
method gets defined.
Add support for i386 architecture and AMD SC520 board
* Patch by Pierre Aubert, 12 Nov 2002:
Add support for DOS filesystem and booting from DOS floppy disk
Add "-n" to linker options to get rid of "Not enough room for
program headers" problem
* Patch by David Müller, 05 Nov 2002
Rename CONFIG_PLL_INPUT_FREQ to CONFIG_SYS_CLK_FREQ
so we can use an already existing name
* Patch by Pierre Aubert, 05 Nov 2002
Hardware related improvements in FDC boot code
* Patch by Holger Schurig, 5 Nov 2002:
Make the PXA really change it's frequency
* Patch by Pierre Aubert, 05 Nov 2002
Add support for slave serial Spartan 2 FPGAs
* Fix uninitialized memory (MAC address) in 8xx SCC/FEC ethernet
drivers
