This is supposed to be a build-system flag. Move it there so we can
define it before linux/kconfig.h is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
The PLL_CMNLC clocks are modelled as a child clock device of seirra. In the
function device_probe, the corresponding clocks are probed before calling
the device's probe. The PLL_CMNLC mux clock can only be created after the
device's probe. Therefore, move assigned-clocks and assigned-clock-parents
to the link nodes in U-Boot device tree file.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
First check the presence of the ipu firmware in the boot partition.
If present enable the ipu and the related clocks & then move
on to load the firmware and eventually start remoteproc IPU1/IPU2.
do_enable_clocks by default puts the clock domains into auto
which does not work well with reset. Hence adding do_enable_ipu_clocks
function.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[Amjad: fix IPU1_LOAD_ADDR and compile warnings]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
J721S2 can support two instances for DDR. Therefore, add the device support
for the same and use 4266MT/s as DDR frequency.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The EVM architecture for J721S2 is similar to that of J721E and J7200. It
is as follows,
+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board
Common Processor board is the baseboard that contains most of the actual
connectors, power supply etc. The System on Module (SoM) is plugged on to
the common processor baord. Therefore, add support for peripherals brought
out in the common processor board.
Link to Common Processor Board: https://www.ti.com/lit/zip/sprr439
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
A System on Module (SoM) contains the SoC, PMIC, DDR and basic high speed
components necessary for functionality. Therefore, add support for the
components present on the SoM.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The J721S2 SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration in automotive ADAS applications and
industrial applications requiring AI at the network edge. This SoC extends
the Jacinto 7 family of SoCs with focus on lowering system costs and power
while providing interfaces, memory architecture and compute performance for
single and multi-sensor applications.
Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, three clusters of lockstep capable
dual Cortex-R5F MCUs, Deep-learning Matrix Multiply Accelerator(MMA), C7x
floating point Vector DSP.
* 3D GPU: Automotive grade IMG BXS-4-64
* Vision Processing Accelerator (VPAC) with image signal processor and
Depth and Motion Processing Accelerator (DMPAC)
* Two CSI2.0 4L RX plus one eDP/DP, two DSI Tx, and one DPI interface.
* Two Ethernet ports with RGMII support.
* Single 4 lane PCIe-GEN3 controllers, USB3.0 Dual-role device subsystems,
* Up to 20 MCANs, 5 McASP, eMMC and SD, OSPI/HyperBus memory controller,
QSPI, I3C and I2C, eCAP/eQEP, eHRPWM, MLB among other peripherals.
* Hardware accelerator blocks containing AES/DES/SHA/MD5 called SA2UL
management.
See J721S2 Technical Reference Manual (SPRUJ28 – NOVEMBER 2021)
for further details: http://www.ti.com/lit/pdf/spruj28
Introduce basic support for the J721S2 SoC.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Update to the 5.16 imx8mq dts files and dt bindings
Changes since v1:
Dropped rfkill.h that is not in linux mainline yet.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Commit 97c16dc8bf ("imx: mx6ull: update the REFTOP_VBGADJ setting")
made this macro unused. Then remove it.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The previous code wrote the contents of the fuse as is in the
REFTOP_VBGADJ[2:0], but this was wrong if you consider the contents of
the table in the code comment. This table is also different from the
table in the commit description. But then, which of the two is correct?
If it is assumed that an unprogrammed fuse has a value of 0 then for
backward compatibility of the code REFTOP_VBGADJ[2:0] must be set to
6 (b'110). Therefore, the table in the code comment can be considered
correct as well as this patch.
Fixes: 97c16dc8bf ("imx: mx6ull: update the REFTOP_VBGADJ setting")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add the PCIe support on i.MX8MM platforms.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de> # Pick from Linux 854a4766ac12 ("arm64: dts: imx8mm: Add the pcie support")
Add the PCIe PHY support on iMX8MM platforms.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de> # Pick from Linux b9ec888f636f ("arm64: dts: imx8mm: Add the pcie phy support")
Fix address of the pad control register
(IOMUXC_SW_PAD_CTL_PAD_SD1_DATA0) for SD1_DATA0_GPIO2_IO2. This seems
to be a typo but it leads to an exception when pinctrl is applied due to
wrong memory address access.
Signed-off-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Fixes: c1c9d41319c3 ("dt-bindings: imx: Add pinctrl binding doc for imx8mm")
Fixes: 748f908cc882 ("arm64: add basic DTS for i.MX8MQ")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de> # Picked from Linux 5cfad4f45806f ("arm64: dts: imx8mm/q: Fix pad control of SD1_DATA0")
Add PLL 1.4 GHz, 1.5 GHz, 1.6 GHz, 1.8 GHz options for iMX8M SoCs
in case they should be operated faster, e.g. to improve boot time.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Linux uses slightly different divider settings for the 1.2 GHz PLL
configuration, adjust the coefficients to match Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
According to TRM for i.MX8M Nano and Plus, GPR10 register contains lock
bit for TZASC_ID_SWAP_BYPASS bit. This bit is required to be set in
order to avoid AXI bus errors when GPU is enabled on the platform.
TZASC_ID_SWAP_BYPASS bit is alread set for all imx8m applicable
derivatives, but is missing a lock settings to be applied.
Set the TZASC_ID_SWAP_BYPASS_LOCK bit for those derivatives which have
it implemented.
Since we're here, provide also names to bits from TRM instead of using
BIT() macro in the code.
Fixes: deca6cfbf5 ("imx8mn: set BYPASS ID SWAP to avoid AXI bus errors")
Fixes: a07c718129 ("imx8mp: set BYPASS ID SWAP to avoid AXI bus errors")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
With the updated device tree's having USB support, enable in
U-Boot. This also requires the addition of the imx8m power
domain, since the USB is gated by the power domain controller.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Resync the SOM and baseboar files with the device trees that will
be included in 5.17-RC1 when it's cut. This will improve pinmuxing
for USDHC1 and add USB functionality.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
As suggested in commit 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") for imx8mm_evk, it is possible to produce
single bootable image via binman. This restores the original behavior in
distros, where only one boot container is used to create target image.
Perform similar adaptions in order to provide single bootable image for
imx8mn-ddr4-evk derivate.
Update documentation to drop additional step of copying u-boot.itb
Fixes: 353dfe4b43 ("imx8mn-ddr4-evk: switch to use binman")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Rather than using odd implicit blob-ext naming, explicitly specify the
type to be of blob-ext and therefore also simplify the node naming.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Some of the nodes were named using a underscore, so rectify this and
consistenly use dashes.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
When using a board variant that selects the lvds specific dtb the
*.u-boot.dtsi file will not be included. To have a lvds dtb specific
u-boot.dtsi file move this part to a common board u-boot.dtsi file and
include this in the board base u-boot.dtsi and create an additional one
for the lvds variant.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Add support of secondary boot address for imx8mn. The secondary
boot address is hardcoded in the fuse. The value is calculated
from there according to the following description:
The fuse IMG_CNTN_SET1_OFFSET (0x490[22:19]) is defined as follows:
- Secondary boot is disabled if fuse value is bigger than 10, n = fuse
value bigger than 10.
- n == 0: Offset = 4MB
- n == 2: Offset = 1MB
- Others & n <= 10 : Offset = 1MB*2^n
- For FlexSPI boot, the valid values are: 0, 1, 2, 3, 4, 5, 6, and 7.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Similar to what has been done before with c5437e5b for u-boot proper, we
enable the SMP bit for SPL as well. This is necessary when SDP booting
straight into Linux, i.e. falcon boot. When SDP boot mode is active, the
ROM code does not set this bit which makes the caches not work once
activated in Linux.
On an i.MX6ULL (528MHz), this reduces a minimal kernel's boot time into
an initramfs shell from ~6.1s down to ~1.2s.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Synchronize DH DHCOM DTs with Linux commit 25960cafa06e ("Linux 5.15.12").
There is no functional change to the resulting DTs. The imx6qdl-dhcom-pdk2.dtsi
had to be adjusted with additional headers, gpio.h, pwm.h, input.h, else
the DT cannot be compiled, the same change is likely necessary in Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add labels to remaining anatop regulators, so their supplies can be
assigned in board DTs. This is similar to Linux kernel commit
93385546ba369 ("ARM: dts: imx6qdl-sabresd: Assign corresponding power supply for LDOs")
except it does not contain the unrelated sabresd changes.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Now the dts information corresponds to the one available in the kernel.
With this patch applied the 'mtd list' shows proper names and
offsets for MTD partitions.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
With the current configuration provided in mxsimage{-spl}.mx28.cfg the
size of SPL binary has been constrained to 32 KiB, due to "LOAD IVT"
command with 0x8000 offset.
The problem was that, the imx28 ROM takes the u-boot.sb and then
extracts from it the IVT header and places it on the 0x8000 OCRAM offset
overwriting any valid (i.e. loaded from eMMC or SPI-NOR) SPL code. This
bug was unnoticed as the overwrite size was just 32 bytes, so the
probability that some important code is altered was low.
However, in the XEA board (where the SPL size is ~39KiB), the overwritten
data was `(struct dm_spi_ops *) 0x800c <mxs_spi_ops>`, which is used
during the boot process.
As a result the SPL execution code hanged with "undefined instruction"
abort as callbacks (with wrong addresses) from it were called.
The fix is to change the OCRAM's offset where IVT is loaded to 0xE000,
so the SPL can grow up to ~57KiB (the maximal size of OCRAM memory
available is 0xE3FC).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
According to the i.MX6ULL Reference Manual, pad CSI_DATA07 may
have the ESAI_TX0 functionality, not ESAI_T0.
Also, NXP's i.MX Config Tools 10.0 generates dtsi with the
MX6ULL_PAD_CSI_DATA07__ESAI_TX0 naming, so fix it accordingly.
There are no devicetree users in mainline that use the old name,
so just remove the old entry.
Fixes: f8ca22b8de ("arm: dts: imx6ull: add pinctrl defines")
Reported-by: George Makarov <georgemakarov1@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Use imx6_src_get_boot_mode() instead of manually reading SBMR1. The
existing function has proper handling for software overrides of the
bootdevice which can happen, for example, when booting from an alternate
source using `bmode`.
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The PDK2 board is capable of running both 100M and 1G ethernet. However,
the i.MX6 has only one ethernet MAC, so it is possible to configure
either 100M or 1G Ethernet. In case of 100M option, the PHY is on the
SoM and the signals are routed to a RJ45 port. For 1G the PHY is on
the PDK2 board with another RJ45 port. 100M and 1G ethernet use
different signal pins from the i.MX6, but share the MDIO bus.
This SoM board combination is used to demonstrate how to enable 1G
ethernet configuration.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
The FXL6408 GPIO expander manages critical devices,
including on-module USB hub. Configure the expander to
switch the USB hub into bypass mode, allowing to use
on-carrier-board USB hub.
Signed-off-by: Oleksandr Suvorov <cryosay@gmail.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Extension boards can be added to Compulab's iot-gate-imx8mm.
We implement extension board manager for detecting the extension
boards.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: uboot-imx <uboot-imx@nxp.com>
Obatin the SoC current temperature in print_cpuinfo().
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The DDRLOCKED bit in CGC2 DDRCLK will auto lock up and down by HW
according to DDR DIV updating or DDR CLK halt status change. So DDR
PCC disable/enable will trigger the lock up/down flow. We
need wait until unlock to ensure clock is ready.
And before configuring the DDRCLK DIV, we need polling the DDRLOCKED
until it is unlocked. Otherwise writing ti DIV bits will not set.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch implements enable_adc1_clk() to enable or disable the ADC1
clock on i.MX8ULP.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Get the MAC address from fuse bank5 word 3 and 4. It has
MSB first at lowest address, so have a reverse order with other
iMX used in mac.c
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When LPAV is allocated to RTD, the LPAV won't be reset. So we have to
reset DCNano and MIPI DSI in u-boot before enabling the drivers
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The LPAV is not allocated to APD when dual boot, so LPAV won't
reset when APD is reset. We have to explicitly reset the DDR,
otherwise its initialization will fail.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
8ULP ROM should read the LPOSC trim BIAS fuse to fill the CGC0
LPOSCCTRL[7:0], but it writes a fixed value on A0.1 revision.
A0.2 will fix the issue in ROM. But A0.1 we have to workaround
it in SPL by setting LPOSCCTRL BIASCURRENT again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Remove the freescale vendor name from CPU revision print to align
with other i.MX platforms
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The setting does not have effect because we should set it after
power on the PS16 for NIC AV.
So move it after upower_init which has powered on all PS
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To avoid DCNANO underrun issue on high loading test, set its
read Qos on NIC_LPAV to highest
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board use IO9 of PCA6416 on LPI2C0 and TPM0 for MIPI DSI MUX and
backlight. However the LPI2C0 and TPM0 are M33 resources, in this
patch we simply access them, but this is a temporary solution.
We will modify it when M33 FW changes to set MIPI DSI panel as default
path and enable backlight after reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the DSI clock enable and disable with PCC reset used.
Add the LCD pixel clock calculation and configuration for DCNano
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Assign the PXP/HIFI4/EPDC to APD domain, otherwise APD not
able to receive interrupts from the modules.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When single boot, assign AP domain as the master domain of the LPAV.
Allocates LPAV master and slave resources like GPU, DCNano, MIPI-DSI
eDMA channel and eDMA request to APD
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
S400 enables RDC only when the DBD_EN is fused. Otherwise, the RDC
is allowed by all masters.
Current S400 has issue if the XRDC has released to A35, then A35 reset
will fail in ROM due to S400 fails to get XRDC.
So temp work around is checking the DBD_EN, if it is not fused, we
don't need to call release XRDC or TRDC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Change boot device logic to also allow environment stored in fat and in
ext4 when booting from SD or from eMMC.
As the boot device check for SD and for eMMC was depending on
ENV_IS_IN_MMC being defined, change the ifdef blocks at env_get_location
to use IS_ENABLED instead for all modes, returning NOWHERE when no valid
mode is found.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Correct printf format for unsigned long long is %llx and not %llxx.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The imx28 uses following voltage supplies hierarchy:
VDD_5V (VDD_BAT) -> VDDIO -> VDDA -> VDDMEM
\-----> VDDD
One shall first enable DCDC on the parent source (VDDIO) and then
follow with its children.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add EA iMX7ULP COM board support for building SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Force selecting features present in SoC i.MX7ULP.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Return the root clock values for MXC_CSPI_CLK, MXC_I2C_CLK,
MXC_UART_CLK and MXC_QSPI_CLK.
At least for the I2C clock the missing support leads to a wrong
configured I2C frequency. The expected value is 100kHz but the resulting
value is about 1MHz.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Non GMAC's MDIO pins should have slew rate disabled for R(G)MII modes. Set
them accordingly in DT.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
This is the promised second part of the sunxi PR for 2022.04, albeit
technially outside of the merge window. We were working on this full
steam since the beginning of the year, and it deserves to be merged,
I think.
The main attraction is support for the F1C100s SoC, which sports a
venerable ARM926 core. Support for this SoC and the LicheePi Nano board
has been in Linux for years, and U-Boot patches were posted mid last
year already.
The new SoC using ARMv5 also means that the bulk of the new code should
not touch any existing boards, although we did some refactorings first,
of course, which actually cleans up some existing sunxi code.
Compile tested for all 160 sunxi boards, and briefly tested on BananaPi M1,
OrangePi Zero, Pine64 and Pine-H64. Tested by others on their boards,
including F1C100s and F1C200s devices.
Add device tree files for suniv and
Lichee Pi Nano it is a board based on F1C100s.
dt-bindings/dts are synced with 5.16.0
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add support for the suniv architecture, which is newer ARM9 SoCs by
Allwinner. The design of it seems to be a mixture of sun3i, sun4i and
sun6i.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add support for F1C100s internal dram controller.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch aims to add header files for the suniv.
The header files included add support for uart, and clocks.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Some Allwinner SoCs use ARM926EJ-S core.
Add Allwinner/sunXi specific code to ARM926EJ-S CPU dircetory.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Both armv7 and arm926ejs use this timer code so move it to mach-sunxi.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The ARMv7 start code has support for saving some boot params at the
entry point, which is used by some SoCs to return to BROM.
Port this to ARM926EJ-S start code.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When we added Allwinner SoC support to ARMv8, we needed to pull in an
implementation of lowlevel_init() calling the C function s_init(), as
sunxi required it as this time.
The last few patches got rid of this bogus requirement, and as sunxi was
still the only user, we can now remove this lowlevel_init.S from ARMv8
altogether.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Currently we do some magic "SRAM setup" MMIO writes in s_init(), copied
from the original BSP U-Boot. The comment speaks of this being required
before DRAM access gets enabled, but there is no indication that this
would actually be required that early.
Move this out of s_init(), into board_init_f(). Since this actually only
affects a very few older SoCs, the actual code goes into the cpu/armv7
directory, to move it out of the way for all other SoCs.
This also uses the opportunity to convert some #ifdefs over to the fancy
IS_ENABLED() macros used in actual C code.
We keep the s_init() stub around for now, since armv8's lowlevel_init
still relies on it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
According to their TRMs, Cortex ARMv7 CPUs with SMP support require the
ACTLR.SMPEN bit to be set as early as possible, before any cache or TLB
maintenance operations are done. As we do those things still in start.S,
we need to move the SMPEN bit setting there, too.
This introduces a new ARMv7 wide symbol and code to set bit 6 in ACTLR
very early in start.S, and moves sunxi boards over to use that instead
of the custom code we had in our board.c file (where it was called
technically too late).
In practice we got away with this so far, because at this point all the
other cores were still in reset, so any broadcasting would have been
ignored anyway. But it is architecturally cleaner to do it early, and
we move a core specific piece of code out of board.c.
This also gets rid of the ARM_CORTEX_CPU_IS_UP kludge I introduced a few
years back, and moves the respective logic into the new Kconfig entry.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far all Allwinner based boards were doing some not-so-lowlevel-setup
in lowlevel's s_init() routine.
This includes the initial clock, timer and pinmux setup, among other
things. This is clearly out of the "absolute bare minimum to get started"
scope that lowlevel_init.S suggests for this function.
Since we have an SPL, which is called right after s_init(), move those
calls to our board_init_f() function. As we overwrite this only for
the SPL, this has the added benefit of not doing this setup *again*
shortly afterwards, when running U-Boot proper.
This makes gpio_init() to be called from the SPL only, so pull this code
into a CONFIG_SPL_BUILD protected part to avoid build warnings.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
There is some code that tries to "reset" the SCTLR_ELx register early in
the boot process. The idea seems to be to guarantee some sane settings
that U-Boot actually relies on, for instance running in little-endian
mode, with the MMU off initially.
However the current code has multiple problems:
- For a start, no platform or config defines the symbol that would
enable that code.
- The code itself really only works if the bits that it tries to clear
are already cleared:
- If we run in big-endian mode initially, any previous loads would have
been wrong already. That applies to the (optional) relocation code,
but more prominently to the mask that it uses to clear those bits:
"ldr x1, =0xfdfffffa" looks innocent, but actually involves a memory
access to the literal pool, using the current endianness.
- If we run with the MMU enabled, we are probably doomed already. We
*could* hope that we are running with an identity mapping, but would
need to do some cache maintenance to avoid losing dirty cache lines.
- The idea of doing a read-modify-write of SCTLR is somewhat
questionable to begin with, because as the owner of the current
exception level we should initialise all bits of this register with a
certain fixed value.
- The code is unnecessarily complicated, and the function name is
misspelled.
While those problems *could* admittedly be fixed, the point that is does
not seem to be used at all at the moment tells me we should just remove
this code, and be it to not give a bad example.
If people care, I could introduce some proper SCTLR initialisation code.
We are about to work this out for the boot-wrapper[1] as we speak, but
apparently we got away without doing this in U-Boot ever since, so it
might not be worth the potential trouble.
[1] https://lore.kernel.org/linux-arm-kernel/20220114105653.3003399-7-mark.rutland@arm.com/
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Setting LINUX_KERNEL_IMAGE_HEADER=y attempts to include an ARM64 Linux
kernel image header at the start of both U-Boot proper and SPL binaries.
However, some definitions that the image header uses are not included by
the SPL linker script, resulting in a build error. Include them the way
they are included in U-Boot proper's linker script to fix the error.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
The commit in the Fixes: tag below broke traffic through switch ports
where the SERDES protocol requires in-band autoneg and this requirement
isn't described in the device tree: SGMII, QSGMII, USXGMII (with
2500Base-X, in-band autoneg isn't supported).
The LS1028A-QDS boards are not yet ready for syncing their device trees
with Linux, since Ethernet is missing there (but has been submitted):
https://lore.kernel.org/lkml/20211112223457.10599-11-leoyang.li@nxp.com/
When agreement is reached for the Ethernet support in Linux, there will
be a sync for these boards as well. For now, just enable in-band autoneg
to fix the breakage.
Fixes: e3789a7262 ("net: dsa: felix: configure the in-band autoneg property based on OF node info")
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Allow device trees to be reused between Linux and U-Boot.
The source for these device trees is linux-next as of commit
bd8a9cd624c6 ("arm64: dts: ls1028a-rdb: update copyright"), which was
chosen because some changes needed to be done to the Linux DTs too,
before they could be shared:
https://lore.kernel.org/linux-arm-kernel/20211202141528.2450169-5-vladimir.oltean@nxp.com/T/#m6f63c92e75fa79a01144b2c2c6dc4776e7971395
There are two more commits on the RDB device tree which haven't been
picked up yet, because they have dependencies on the SoC device tree:
dd3d936a1b17 ("arm64: dts: ls1028a: add ftm_alarm1 node to be used as wakeup source")
b2e2d3e02fb6 ("arm64: dts: ls1028a-rdb: enable pwm0")
These will be picked up on the next resync.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reuse the scheme implemented by the Kontron SL28 boards in
commit d08011d7f9
("arm: dts: ls1028a: disable the PCIe controller by default")
and move the 'status = "okay"' lines for the PCIe controllers
inside a separate U-Boot dtsi for the LS1028A-RDB board. This way, the
existing Linux device tree can simply be dropped in.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is no I2C peripheral on these buses on the reference design board,
and the Linux device tree does not enable them either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is no SPI peripheral on the LS1028A-RDB, therefore no reason to
enable these nodes in the U-Boot device tree (and Linux does not enable
them either).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In a bit of a blunder, the blamed commit in the Fixes: tag below made
the mscc_felix switch driver look at the 'managed = "in-band-status"'
device tree property, forgetting that the U-Boot device tree had not
been updated to include that property, whereas the Linux one does.
The switch is therefore described in the device tree as not requiring
in-band autoneg, but the PHY driver for VSC8514 (drivers/net/phy/mscc.c)
still enables that feature. This results in a mismatch => no traffic.
This patch is a copy-paste of the Ethernet device tree nodes from Linux,
which resolves that issue. The device tree update also renames the
Ethernet PHY labels.
Fixes: e3789a7262 ("net: dsa: felix: configure the in-band autoneg property based on OF node info")
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The nodes in the NXP LS1028A-RDB device tree are out of order, regroup
them alphabetically to have a simple delta when the Linux device tree is
brought in.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
During the LS1028A-RDB sync with Linux device trees, it was observed
that the same RTC is present on the two boards, and the wrong compatible
string is used in both places. This change updates the RTC from the
LX2160A-RDB to use the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
During this board's sync with Linux device trees, it was observed that
it doesn't use the same compatible string for the RTC node as in U-Boot.
This change makes the RTC compatible strings match, for a smoother sync.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The LS1028A-QDS board won't be synced with the Linux device trees right
now, since those are currently still in progress (Ethernet is missing).
However, while we're at converting the RDB, it can be observed that the
same RTC is present on the two boards, and the wrong compatible string
is used in both places. This change updates the RTC from the QDS to use
the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
During the LS1028A-RDB sync with Linux device trees, it was observed
that the same RTC is present on the two boards, and the wrong compatible
string is used in both places. This change updates the RTC from the
LX2160A-QDS to use the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
During the LS1028A-RDB sync with Linux device trees, it was observed
that the same RTC is present on the two boards, and the wrong compatible
string is used in both places. This change updates the RTC from the
LS1088A-RDB to use the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
During the LS1028A-RDB sync with Linux device trees, it was observed
that the same RTC is present on the two boards, and the wrong compatible
string is used in both places. This change updates the RTC from the
LS1088A-QDS to use the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Even not used by u-boot, this has to be inline with the hw and kernel dts.
U-boot partition table is defined by MTDPARTS_DEFAULT Kconfig.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Beside that mounted rgmii debug phy is 1000Mbps capable, the debug link
between the piggy board and the phy is 100Mbps only.
This leads to longer link establishment time when working in debug mode,
as phy tries to autoneg 1000Mbps.
This patch fixes the speed to 100Mbps and allows smother link establishment
time for the debug interface.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Although it isn't known what bit 0 in PHY reg 8 does, it's obvious that
it has to be set before read calibration and cleared afterwards. This is
already done for first rank, but not for second (copy & paste error.)
Fix it.
Fixes: f4317dbd06 ("sunxi: Add H616 DRAM support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Kconfig symbol is missing CONFIG_ prefix, so compiler will always
skip ODT configuration.
Fix symbol name.
Fixes: f4317dbd06 ("sunxi: Add H616 DRAM support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For sunxi boards with the AXP209, AXP221, AXP809, and AXP818 PMICs
(plus possibly others, I only confirmed the datasheets for these),
it is sometimes desirable to not boot whenever the device is
plugged in. An example would be when using the NTC CHIP inside a
PocketCHIP.
This provides a configurable option to check if bit 0 of
register 0 of the PMIC says it was powered because of a power button
press (0) or a plug-in event (1). If the value is 1 and this option
is selected, the device shuts down shortly after printing a message
to console stating the reason why it's shutting down. Powering up the
board with the power button is not affected.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
[Andre: reword to speak of boot, remove #ifdefs]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The calls for flipping bits in the Allwinner pin controller registers
were using unnecessarily complex pointer arithmetic.
Improve readability by simplifying the expression.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The GPIO and pinctrl drivers need these setters for pin configuration.
Since they are DM drivers, they should not be using hardcoded base
addresses. Factor out variants of the setter functions which take a
pointer to the GPIO bank's MMIO registers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The return values of these functions are always zero, and they are
never checked. Since they are not needed, remove them.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
ROM supports cpsw_port2 for Ethernet boot and SPL stages continue to
download images on the same port, therefore there is no need to enable
cpsw_port1. Disable the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Since commit 9855034397 ("fdt: Don't call board_fdt_blob_setup()
without OF_BOARD") board_fdt_blob_setup() is no more called on
STM32MP platforms in trusted boot which hangs during boot process.
Enable OF_BOARD flag to fix this issue.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add the partition name and remove the line number in error messages
of treat_partition_list() to provide correct information to user of
STM32CubeProgrammer.
The "line number" value was confusing because it is incorrect here;
the index in part_array[] is not aligned with the line number in
the parsed Layout file, because the empty lines and the lines beginning
by '#' are skipped during the first parsing in parse_flash_layout().
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Synchronize DH DHCOM DTs with Linux commit 25960cafa06e ("Linux 5.15.12").
There is no functional change to the resulting DTs. The eeprom0 alias and
PHY reset GPIO are now reinstated in SoM u-boot dtsi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Synchronize DH DHCOR DTs with Linux commit 25960cafa06e ("Linux 5.15.12").
There is no functional change to the resulting DTs. The eeprom0 alias is
now reinstated in SoM u-boot dtsi, the PHY reset GPIO is reinstated in AV96
u-boot dtsi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Device tree alignment with Linux kernel v5.16-rc5
- ARM: dts: stm32: set otg-rev on stm32mp151
- ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151
- ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
- ARM: dts: stm32: fix SAI sub nodes register range
- ARM: dts: stm32: fix STUSB1600 Type-C irq level on stm32mp15xx-dkx
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Default value for CONFIG_SYS_BOOTCOUNT_SINGLEWORD and
CONFIG_SYS_BOOTCOUNT_ADDR are only needed when
CONFIG_BOOTCOUNT_GENERIC is used.
This patch avoids to define these configs when an other bootcount backend
is activated, for example for CONFIG_BOOTCOUNT_ENV.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Today the bootcount is not managed by the Linux kernel for STM32MP15 as
we don't have driver to update the used backup register in TAMP and the
recovery command still executes the normal bootcmd with
'altbootcmd=run bootcmd'.
So the bootcount feature is never used, the config CONFIG_BOOTCOUNT_LIMIT
and the associated environment variable 'altbootcmd' can be removed to
reduce the U-Boot size.
Each boards can re-enable this feature later in their defconfig, if it is
needed, with the expected backend, for example CONFIG_BOOTCOUNT_GENERIC
or CONFIG_BOOTCOUNT_ENV.
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch configures U-Boot SPL for DHCOR SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
To start U-Boot on DHCOR based board, e.g. Avenger96, proceed as follows:
- Install dfu-util on the host PC (in debian this is package 'dfu-util')
- Power off the Avenger96 board.
- Connect both USB-serial console and USB-OTG microB ports to host PC.
- Switch Avenger96 to USB boot mode -- BOOT0..2 switches all set to 0.
- Power on the Avenger96 board.
- Verify using '$ dmesg' that a new device has been detected as follows:
New USB device found, idVendor=0483, idProduct=df11, bcdDevice= 2.00
New USB device strings: Mfr=1, Product=2, SerialNumber=3
Product: DFU in HS Mode @Device ID /0x500, @Revision ID /0x0000
Manufacturer: STMicroelectronics
- Upload U-Boot SPL:
$ dfu-util -a 1 -D u-boot-spl.stm32
- Upload U-Boot proper:
$ dfu-util -a 0 -D u-boot.itb
- At this point, SPL will wait for user to press "Ctrl-C" on serial
console. When ready to interact with U-Boot, press Ctrl-C to start
the bootloader.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In case the SoC reports the boot device type is USB, it means the SPL was
loaded via BootROM DFU mode. Currently the spl_boot_device() returns boot
device as USB host, change it to DFU instead, so the SPL can continue the
DFU boot and load U-Boot via DFU.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When booting from QSPI, the boot ROM appears to mux the QSPI
pins, but it's not guaranteed to be setup when booting from
eMMC. Fix this by explicitly configuring the pinmux.
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_AT91_EFLASH
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Eugen Hristev <eugen.hristev@microchip.com>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
Use the preferred
if (IS_ENABLED(X))
instead of
#ifdef X
where possible.
There are still places where this is not possible or is more complicated
to convert in this file. Leave those be for now.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Checkpatch warns about using uint32/16/8_t instead of u32/16/8.
Use the preferred types.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Print the wrong srcaddr (spl_image->offset) in error message also for
SATA case.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Last 4 bytes of kwbimage boot image is checksum. Verify it via the new
spl_check_board_image() function which is called by U-Boot SPL after
loading kwbimage.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Each boot mode has its own kwbimage specified by blockid. So check that
kwbimage is valid by blockid.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add parameter spl_boot_device to spl_parse_board_header(), which allows
the implementations to see from which device we are booting and do
boot-device-specific checks of the image header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
There are certain restrictions for kwbimage offset and blocksize.
Validate them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Kirkwood uses macros KW_DEFADR_PCI_MEM and KW_DEFADR_PCI_IO for base
address of PCIe mappings. Size of PCIe windows is not defined in any macro
yet, so export them in new KW_DEFADR_PCI_MEM_SIZE and KW_DEFADR_PCI_IO_SIZE
macros.
Kirkwood arch code already maps mbus windows for io and mem, so avoid
calling mvebu_mbus_add_window_by_id() function which would try to do
duplicate window mapping.
Kirkwood PCIe controllers already use "marvell,kirkwood-pcie" DT compatible
string, so mark pci_mvebu.c driver as compatible for it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add macro fdt_for_each_node_by_compatible() to allow iterating over
fdt nodes by compatible string.
Convert various usages of
off = fdt_node_offset_by_compatible(fdt, start, compat);
while (off > 0) {
code();
off = fdt_node_offset_by_compatible(fdt, off, compat);
}
and similar, to
fdt_for_each_node_by_compatible(off, fdt, start, compat)
code();
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
=HtB+
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
There are 4 MDIO bus controllers in AST2600 SOC. Each of them can
connect to one or more PHY chips and is flexible to work with the 4 MAC
devices in AST2600. On AST2600 EVB, MDIO 0,1,2,3 connect to the PHY
chips used by MAC 0,1,2,3 respectively.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
