TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also remove CONFIG_LTO=y now that there is sufficient space for SPL in
SPI flash, and to fix a build issue reported by Peter Robinson.
Fixes: 5713135ecc ("rockchip: rockpro64: Build u-boot-rockchip-spi.bin")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
BootRom will try to load TPL+SPL from media in the following order:
- SPI NOR Flash
- SPI NAND Flash
- NAND Flash
- eMMC
- SDMMC
SPL will try to load FIT from media in the order defined in the device
tree u-boot,spl-boot-order property.
Change the default order to load FIT from to:
- same media as TPL+SPL
- SDMMC
- eMMC
Boards with strict load order requirements should override the
u-boot,spl-boot-order property in the board specific u-boot.dtsi.
Fixes: 42f67fb51c ("rockchip: rk3568: Fix boot device detection")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph-all prop to common pinctrl nodes for eMMC, FSPI, SD-card and
UART2 that are typically used by multiple boards. Unreferenced nodes are
removed from the SPL device tree during a normal build.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz compute module is mostly pin-compatible with the RPi
CM4 form factor. Therefore, it can slot into the official Raspberry Pi
CM4 IO carrier board. Add this configuration to U-Boot.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz Blade board is a carrier board for the SOQuartz
CM4-compatible compute module. It features PoE, an M.2 slot, an SD card
slot, HDMI, USB, serial and ethernet.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz Model A board is a carrier board for the SOQuartz
CM4-compatible compute module. It exposes PCIe, ethernet, USB, HDMI,
CSI, DSI, eDP and a 40 pin GPIO header, and is powered by 12V DC.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model B is a credit-card sized single-board
computer based on the Rockchip RK3566 SoC. The board features an M.2
PCIe slot, USB3, USB2, eMMC, SD, ethernet, HDMI, analog audio out, a
40 pin GPIO header and a DSI and CSI port, as well as on-board Wi-Fi.
Features tested on a Quartz64-B 4GB v1.4 2022-06-06:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model A is a single-board computer based on the
Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0,
CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a
20 pin GPIO header.
Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove regulator-boot-on prop from regulators now that the phy core has
support for phy-supply after the commit c57e0dcd93 ("phy: add support
for phy-supply").
This reverts commit 7911f409ff.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit ec107f04b6 ("rockchip: chromebook_minnie: Enable sound") and
commit 2d0c01b8f0 ("sound: rockchip: Add sound support for jerry")
enable audio support for chromebook_minnie and chromebook_jerry. Enable
it for chromebook_speedy as well, but put the non-upstream sound node
in the board -u-boot.dtsi instead.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3288-veyron-speedy-u-boot.dtsi file duplicates the bootphase dts
fragments from rk3288-veyron-u-boot.dtsi even though it #inclues that.
Deduplicate these into the latter file, which should also make the eMMC
available to the other veyron boards' SPL.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit 9b312e26fc ("rockchip: Enable building a SPI ROM image on
jerry") produces a u-boot.rom file for chromebook_jerry, intended to be
written to SPI flash. Build this file for other veyron boards as well,
especially because they are already configured only to boot from SPI.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Boot devices defined in rk3308.c and in rk3308.dtsi do not match, causing
'same-as-spl' feature not to work. Update DTS definitions, aligning to
Linux kernel DTS and to other Rockchip DTS files, i.e. from dwmmc to mmc.
Add rk3308-rock-pi-s.dtb in dtb-y targets for CONFIG_ROCKCHIP_RK3308.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some ROCK Pi S SKU/models are not equipped with SD-NAND (eMMC),
therefore SPL needs access to sdmmc: add it to rk3308-u-boot.dtsi
with bootph-all property.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Call to board_debug_uart_init() is useless, as mainline U-Boot can
not build TPL for rk3308, and proprietary ddr.bin to be used as TPL
is responsible to init debug uart. Moreover current implementation
of board_debug_uart_init() is not compatible with ROCK Pi S, as it
sets pins for UART2 channel 1 breaking access to sdmmc due to pinmux
conflict. Debug uart for ROCK Pi S is UART0.
Thus, avoid ROCKCHIP_RK3308 to select DEBUG_UART_BOARD_INIT and allow
to deselct it in rock-pi-s-rk3308_defconfig. The DEBUG_UART_BOARD_INIT
is already implied by ARCH_ROCKCHIP, therefore other boards based on
rk3308 chip are not affected by change.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Definition of function board_debug_uart_init() must be under
CONFIG_DEBUG_UART_BOARD_INIT and not under CONFIG_DEBUG_UART,
as it was: see debug_uart.h. In this way the debug uart can
be used but its board-specific initialization skipped by
configuration, if useless.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Resync some of the K3 DTS files with the kernel, and pull in some
required related updates to keep drivers in sync with the dts files
now. Bring in some incremental fixes on top of one of the series I
applied recently as well as updating the iot2050 platform. Also do a
few small updates to the K2 platforms.
The following checks are more reasonable as the previous logs were a bit
misleading as we could still get the logs that the authetication is
being skipped but still authenticate. Move the debug prints and checks
to proper locations.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Fix missing declaration of fdt_del_node_path() while compiling am625_fdt.c and
missing common_fdt.h include in common_fdt.c
Fixes: 70aa5a94d4 ("arm: mach-k3: am62: Fixup CPU core, gpu and pru nodes in fdt")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
This avoids having to maintain to defconfigs that are 99% equivalent.
The approach is to use binman to generate two flash images,
flash-pg1.bin and flash-pg2.bin. With the help of a template dtsi, we
can avoid duplicating the common binman image definitions.
Suggested-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Update the am62 and am625 device-trees from linux v6.5-rc1. This needed
the following tweaks to the u-boot specific dtsi as well:
- Switch tick-timer to the main_timer as it's now defined in the main dtsi
- Secure proxies are defined in SoC dtsi
- Drop duplicate nodes - u-boot.dtsi is includes in r5-sk, no need for
either the definitions from main.dtsi OR duplication from u-boot.dtsi
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Maxime Ripard <mripard@kernel.org>
Cc: Francesco Dolcini <francesco@dolcini.it>
Cc: Sjoerd Simons <sjoerd@collabora.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Timer0 is used by u-boot as the tick timer; Add it to the soc devices
list so it can be enabled via the k3 power controller.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Cc: Francesco Dolcini <francesco@dolcini.it>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Hardkernel ODROID-M1 is a single board computer with a RK3568B2 SoC,
a slightly modified version of the RK3568 SoC.
Features tested on a ODROID-M1 8GB v1.0 2022-06-13:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe/AHCI
- SATA port
- USB host
Device tree is imported from linux v6.4.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update config, IO and memory regions used based on [1] with pcie3x2
config reg address and reg size corrected.
Before this change:
PCI Autoconfig: Bus Memory region: [0-3eefffff],
PCI Autoconfig: Bus I/O region: [3ef00000-3effffff],
After this change:
PCI Autoconfig: Bus Memory region: [40000000-7fffffff],
PCI Autoconfig: Bus I/O region: [f0100000-f01fffff],
[1] https://lore.kernel.org/lkml/20221112114125.1637543-2-aholmes@omnom.net/
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add missing pinctrl and defconfig options to enable PCIe and NVMe
support on Radxa ROCK 3 Model A.
Use of pcie20m1_pins and pcie30x2m1_pins ensure IO mux selection M1.
The following pcie_reset_h and pcie3x2_reset_h ensure GPIO func is
restored to the perstn pin, a workaround to avoid having to define
a new rockchip,pins.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add board-specific devicetree/config for the RK3399T-based Radxa ROCK 4SE
board. This board offers similar peripherals in a similar form-factor to
the existing ROCK Pi 4B but uses the cost-optimised RK3399T processor
(which has different OPP table than the RK3399) and other minimal hardware
changes.
Kernel tag: next-20230719
Kernel commits:
- 86a0e14a82ea ("arm64: dts: rockchip: Add Radxa ROCK 4SE")
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To prepare for ROCK 4 SE support, changes are needed to the common ROCK
Pi 4 devicetree to move the OPP from the common devicetree to individual
board devicetrees. Sync the Rockchip RK3399 ROCK Pi 4-related DTs from
Linux to gain from these changes.
Kernel tag: next-20230719
Kernel commits:
cfa12c32b96f ("arm64: dts: rockchip: correct wifi interrupt flag in Rock \
Pi 4B")
cee572756aa2 ("arm64: dts: rockchip: Disable HS400 for eMMC on ROCK Pi 4")
2bd1d2dd808c ("arm64: dts: rockchip: Disable HS400 for eMMC on ROCK 4C+")
fd2762a62646 ("arm64: dts: rockchip: Move OPP table from ROCK Pi 4 dtsi")
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For RK322x series ARM SoCs the OP-TEE is non-optional, as besides the TEE
it also provides the PSCI implementation, which is expected to be available
by upstream linux.
Select CONFIG_SPL_OPTEE_IMAGE if an FIT image is built.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_SPL_OPTEE_IMAGE option is used during DRAM size detection for
Rockchip ARM platform to indicate that an OP-TEE binary was already loaded
and a Trusted Execution Environment (TEE) is available in order to
block/reserve a memory-region for it.
This adds a bunch of new `#if's` to u-boot-rockchip.dtsi to include the
OP-TEE binary in the FIT image for ARM SOCs if CONFIG_SPL_OPTEE_IMAGE is
selected.
That makes it a little harder to read, but I opted for that, because all
the duplicates in an extra ARM-OP-TEE-specfic .dtsi would be the greater
evil, IMHO. Besides it's more likley being "forgotten" to sync when changes
in u-boot-rockchip.dtsi are made.
The no longer required rockchip-optee.dtsi and it's inclusions are dropped.
The hardcoded load address is common across all OP-TEE implemenations for
Rockchip (vendor and upstream).
The OP-TEE-binary is non-optional if CONFIG_SPL_OPTEE_IMAGE is selected and
there will be an error if the file does not exist and/or `TEE=` build
option is missing.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Current SYS_MALLOC_F_LEN of 0x2000 (8 KB) used in SPL is too small for
some RK3568 boards. SPL will print following during boot:
alloc space exhausted
Increase the default SYS_MALLOC_F_LEN to 0x20000 (128 KB) to mitigate.
Fixes: 2a950e3ba5 ("rockchip: Add rk3568 architecture core")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Long are gone the times TF-A couldn't handle the FDT passed by U-Boot.
Specifically, since commit e7b586987c0a ("rockchip: don't crash if we
get an FDT we can't parse") in TF-A, failure to parse the FDT will use
the fallback mechanism. This patch was merged in TF-A v2.4-rc0 from two
years ago.
New boards should likely have this option disabled or explicitly enable
it in their respective defconfig.
Because existing boards might depend on a TF-A version that predates
v2.4, let's just enable this option in all RK3399 defconfigs.
Maintainers of each board can decide for themselves if they would prefer
to disable this option and allow U-Boot to pass the DT to TF-A.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6B(Neu6B) is a 96boards SoM-CB compute module
based on Rockchip RK3588J from Edgeble AI.
Add support for this SoM and IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6B(Neu6B) is a 96boards SoM-CB compute module
based on Rockchip RK3588J from Edgeble AI.
General features:
- Rockchip RK3588J
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
- On module WiFi6/BT
Neural Compute Module 6B(Neu6B) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
General features:
- microSD slot
- 1x HDMI Out
- 1x HDMI In
- 2x DP
- 1x eDP
- 2x MIPI DSI connector
- 4x MIPI CSI2 connector
- 2x USB Host
- 2x USB 3.0 OTG/Host
- 1x SATA
- 1x 2.5Gbps Ethernet
- 1x M.2 B-Key for 4G/5G cards
- 1x M.2 M-Key slot
- 1x Onboard PoE
- 1x RS485, RS232, CAN
- 1x Audio, MIC port
- RTC battery slot
- 40-pin GPIO expansion
Neu6B needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6B(Neu6B) IO platform.
Kernel commits:
commit <5f06c3f508f7> ("arm64: dts: rockchip: Add rk3588 Edgeble Neu6
Model B SoM")
commit <3a9181a43b94> ("arm64: dts: rockchip: Add rk3588 Edgeble Neu6
Model B IO")
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add rk3588j-u-boot.dtsi for adding U-Boot specific nodes and
properties for Rockchip RK3588J SoC.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip RK3588J is the industrial-grade version of RK3588 SoC and
is operated with -40 °C to +85 °C temparature.
Add rk3588j specific dtsi for adding rk3588j specific operating points
and other changes to be add in future.
Kernel commit:
commit <8274a04ff1dc> ("arm64: dts: rockchip: Add Rockchip RK3588J")
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
FriendlyARM NanoPi R5C is an open-sourced mini IoT gateway device.
Specification:
- Rockchip RK3568
- 1/4GB LPDDR4X RAM
- 8/32GB eMMC
- SD card slot
- M.2 Connector
- 2x USB 3.0 Port
- 2x 2500 Base-T (PCIe, r8125)
- HDMI 2.0
- MIPI DSI/CSI
- USB Type C 5V
The device tree is taken from kernel v6.4-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
FriendlyARM NanoPi R5S is an open-sourced mini IoT gateway device.
Board Specifications
- Rockchip RK3568
- 2 or 4GB LPDDR4X
- 8GB or 16GB eMMC, SD card slot
- GbE LAN (Native)
- 2x 2.5G LAN (PCIe)
- M.2 Connector
- HDMI 2.0, MIPI DSI/CSI
- 2xUSB 3.0 Host
- USB Type C PD, 5V/9V/12V
- GPIO: 12-pin 0.5mm FPC connector
The device tree is taken from kernel v6.4-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and RAM type
changed from DDR4 to LPDDR3.
The device tree is taken from kernel v6.4-rc1.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.
The device tree and description are taken from kernel v6.3-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Add support for the DSI and DSI-DPHY to U-Boot for the RGxx3. These are
needed so we can send a panel ID request to determine which panel is
being used.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The pinctrl on the Anbernic RGxx3 for the i2c2 bus does not use the
default value, so explicitly define it.
Fixes: 6cf6fe2537 ("board: rockchip: add Anbernic RGXX3 Series Devices")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the USB3.0 host node, and gadget node.
The gadget is available through the USB type C connector on the board.
The connector is tied to a Fairchild fusb302b device, which currently
does not have a driver in U-boot, but the node is here for correct
description of the board + Linux future compatibility.
It will be easier to move the node as-is when it will be available
in the DT from Linux
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the USB 3.0 devices in rk3588:
- USB DRD(dual role device) 3.0 #0 as usbdrd3_0 which is available in
rk3588s
- USB DRD(dual role device) 3.0 #1 as usbdrd3_1 which is available in
rk3588 only
- USB DP PHY (combo USB3.0 and DisplayPort Alt Mode ) #0 phy interface
as usbdp_phy0
- USB DP PHY (combo USB3.0 and DisplayPort Alt Mode ) #1 phy interface
as usbdp_phy1
- USB 2.0 phy #2 , the USB 3.0 device can work with this phy in USB 2.0
mode
- associated GRFs (general register files) for the devices.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
[eugen.hristev@collabora.com: move nodes to right place, adapt from latest
linux kernel]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the devicetree with linux-next tag: next-20230525
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Since commit 56670d6fb8 ("disk: part: use common api to lookup part
driver") part_get_info_by_name_type() ignores the part_type parameter
used to restrict the partition table type.
omap_mmc_get_part_size() and part_get_info_by_name() are the only
consumers.
omap_mmc_get_part_size() calls with part_type = PART_TYPE_EFI because at
the time of implementation a speed up could be gained by passing the
partition table type. After 5 years experience without this restriction
it looks safe to keep it that way.
part_get_info_by_name() uses PART_TYPE_ALL.
Move the logic of part_get_info_by_name_type() to part_get_info_by_name()
and replace the function in omap_mmc_get_part_size().
Fixes: 56670d6fb8 ("disk: part: use common api to lookup part driver")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit d927d1a808, reversing
changes made to c07ad9520c.
These changes do not pass CI currently.
Signed-off-by: Tom Rini <trini@konsulko.com>
Emulate Secure World's FF-A ABIs and allow testing U-Boot FF-A support
Features of the sandbox FF-A support:
- Introduce an FF-A emulator
- Introduce an FF-A device driver for FF-A comms with emulated Secure World
- Provides test methods allowing to read the status of the inspected ABIs
The sandbox FF-A emulator supports only 64-bit direct messaging.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
add support for x0-x17 registers used by the SMC calls
In SMCCC v1.2 [1] arguments are passed in registers x1-x17.
Results are returned in x0-x17.
This work is inspired from the following kernel commit:
arm64: smccc: Add support for SMCCCv1.2 extended input/output registers
[1]: https://documentation-service.arm.com/static/5f8edaeff86e16515cdbe4c6?token=
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
- Actually merge the assorted K3 platform improvements that were
supposed to be in commit 247aa5a191 ("Merge branch
'2023-07-21-assorted-TI-platform-updates'")
The USB 3.0 driver xhci-mem.c requires CONFIG_SYS_CACHELINE_SIZE to be set.
Define the cache line size for QEMU on RISC-V to be 64 bytes.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Harts need to use per-hart stack before any function call, even if that
function is a simple one. When the callee uses stack for register save/
restore, especially RA, if nested call, concurrent access by multiple
harts on the same stack will cause data-race.
This patch sets up SP before `board_init_f_alloc_reserve`. A side effect
of this is that the memory layout has changed as the following:
+----------------+ +----------------+ <----- SPL_STACK/
| ...... | | hart 0 stack | SYS_INIT_SP_ADDR
| malloc_base | +----------------+
+----------------+ | hart 1 stack |
| GD | +----------------+ If not SMP, N=1
+----------------+ | ...... |
| hart 0 stack | +----------------+
+----------------+ ==> | hart N-1 stack|
| hart 1 stack | +----------------+
+----------------+ | ...... |
| ...... | | malloc_base |
+----------------+ +----------------+
| hart N-1 stack| | GD |
+----------------+ +----------------+
| | | |
Signed-off-by: Bo Gan <ganboing@gmail.com>
Cc: Rick Chen <rick@andestech.com>
Cc: Leo <ycliang@andestech.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Enabling FIT_SIGNATURE required the old authentication method to be
disabled so disable this for K3 SOCs and enable FIT_SIGNATURE for K3
Platforms.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
[ cleanup the patch ]
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
FIT signature requires the updates to u-boot.dtb and the DTB that we
pack don't get updates with the changes of the signature node.
Pack u-boot.dtb as the default DTB so that the signature node changes
can be reflected in them.
(Note, this is only packaging the primary platform and the secondary
platform will require manual changes for the FIT signature enablement)
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
[ add additional boards that were missing ]
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The 'gsub' setexpr sub command is using when creating the FIT image
configuration string on K3 devices. Enable this for K3.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The background firewall calculations were wrong, fix that to determine
both the background and foreground correctly.
Fixes: 8bfce2f998 ("arm: mach-k3: common: reorder removal of firewalls")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Fix the regression that occurred during the alignment of binman series
merges along with these HS fixes that caused silent regression in this.
Fixes: 30a7ee87fd ("Kconfig: j721s2: Change K3_MCU_SCRATCHPAD_BASE to non firewalled region")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Fix regression occurred during refactoring for the mentioned commit.
Fixes: bd6a247593 ("arm: mach-k3: security: separate out validating binary logic")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Since binman is used to package bootloader images for all K3 devices, we
do not have to rely on the earlier methods to package them.
Scripts that were used to generate x509 certificate for tiboot3.bin and
generate tispl.bin, u-boot.img have been removed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Move to using binman to generate tispl.bin which is used to generate the
final flash.bin bootloader for iot2050 boards.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
By providing entries in the binman node of the device tree, binman will
be able to find and package board config artifacts generated by
TIBoardConfig with sysfw.bin and generate the final image sysfw.itb.
It will also pick out the R5 SPL and sign it with the help of TI signing
entry and generate the final tiboot3.bin.
Entries for A72 build have been added to k3-j721e-binman.dtsi to
generate tispl.bin and u-boot.img.
Support has been added for both HS-SE(SR 1.1), HS-FS(SR 2.0) and GP images
In HS-SE, the encrypted system firmware binary must be signed along with
the signed certificate binary.
HS-SE:
* tiboot3-j721e_sr1_1-hs-evm.bin
* sysfw-j721e_sr1_1-hs-evm.itb
* tispl.bin
* u-boot.img
HS-FS:
* tiboot3-j721e_sr2-hs-fs-evm.bin
* sysfw-j721e_sr2-hs-fs-evm.itb
* tispl.bin
* u-boot.img
GP:
* tiboot3.bin -->tiboot3-j721e-gp-evm.bin
* sysfw.itb --> sysfw-j721e-gp-evm.itb
* tispl.bin_unsigned
* u-boot.img_unsigned
It is to be noted that the bootflow followed by J721E requires:
tiboot3.bin:
* R5 SPL
* R5 SPL dtbs
sysfw.itb:
* TIFS
* board-cfg
* pm-cfg
* sec-cfg
* rm-cfg
tispl.bin:
* DM
* ATF
* OP-TEE
* A72 SPL
* A72 SPL dtbs
u-boot.img:
* A72 U-Boot
* A72 U-Boot dtbs
Reviewed-by: Simon Glass <sjg@chromium.org>
[afd@ti.com: changed output binary names appropriately]
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Board config binary artifacts must be generated to be used by binman to
package sysfw.itb and tiboot3.bin for all K3 devices.
For devices that follow combined flow, these board configuration
binaries must again be packaged into a combined board configuration
blobs to be used by binman to package tiboot3.bin.
Add common k3-binman.dtsi to generate all the board configuration
binaries needed.
Also add custMpk.pem and ti-degenerate-key.pem needed for signing GP and
HS bootloader images common to all K3 devices.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Use spl_dcache_enable, in place of setup_dram, arch_reserve_mmu to set
up pagetable, initialise DRAM and enable Dcache to avoid multiple
function calls.
Check for CONFIG_SPL_VIDEO in place of CONFIG_SPL_VIDEO_TIDSS to prevent
any build failure in case video config is not defined and video related
functions are called.
Check for CONFIG_SPL_SPLASH_SCREEN and CONFIG_SPL_BMP before calling
splash_display to avoid compilation failure.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
In spl_dcache_enable after setting up page table, set gd->relocaddr
pointer to tlb_addr, to get next location to reserve memory. Align
tlb_addr with 64KB address.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
There is little need to print the devstat information or when we exit a
function during a typical boot. Remove them to reduce the noise during
typical operation
Signed-off-by: Bryan Brattlof <bb@ti.com>
The function declaration for force_emif_self_refresh takes no parameters
but does not specify this, only the prototype in the headers do. As
clang will warn about this, correct it.
Signed-off-by: Tom Rini <trini@konsulko.com>
AM62x SoC is available in multiple variant:
- CPU cores (Cortex-A) AM62x1 (1 core), AM62x2 (2 cores), AM62x4 (4 cores)
- GPU AM625x with GPU, AM623x without GPU
- PRU (Programmable RT unit) can be present or not on AM62x2/AM62x4
Remove the relevant FDT nodes by reading the actual configuration
from the SoC registers, with that change is possible to have a single
dts/dtb file handling the different variant at runtime.
While removing GPU node and CPU nodes also the watchdog node
in the same Module Domain is removed.
A similar approach is implemented for example on i.MX8 and STM32MP1 SoC.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Add register address and relevant bitmasks and shifts.
Allow reading these information:
- device identification
- number of cores (part of device identification)
- features (currently: PRU / no PRU)
- security
- functional safety
- speed grade
- temperature grade
- package
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andrew Davis <afd@ti.com>
ft_system_setup cannot be enabled on SoC without msmc sram otherwise
fdt_fixup_msmc_ram function fails causing system reset.
Fix by moving fdt_fixup_msmc_ram to common_fdt.c file and creating
SoC (AM654, J721E and J721S2) specific files for fdt fixups.
This change was verified to not change anything on any existing board
(all the J721S2, AM654 and J721E boards requires it,
none of the remaining k3 boards require it).
Fixes: 30e96a2401 ("arm: mach-k3: Move MSMC fixup to SoC level")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
On security enforced (HS-SE) devices ROM firewalls OSPI data region3 that
is present in above 64bit region. Open this up in bootloader to allow
Linux to access OSPI flashes in mmap mode.
Without this kernel will crash when accessing this region due to
firewall violations on HS-SE devices.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
For once this adds USB support for two SoCs: the H616 and the F1C100s
series. The rest is support for LPDDR3 DRAM chips on H616 boards.
Gitlab CI passed, and I booted that briefly on an H616 and an F1C200s
board. I don't have an H616 board with LPDDR3 DRAM, but reportedly that
works for Mikhail, and doesn't regress on my DDR3 boards.
axi_emac:
- Change return value if RX packet is not ready
cadence_qspi:
- Enable flash reset for Versal NET
dt:
- Various DT syncups with Linux kernel
- SOM - reserved pmufw memory location
fpga:
- Add load event
mtd:
- Add missing dependency for FLASH_CFI_MTD
spi/nand:
- Minor cleanup in Xilinx drivers
versal-net:
- Prioritize boot device in boot_targets
- Wire mini ospi/qspi/emmc configurations
watchdog:
- Use new versal-wwdt property
xilinx:
- fix sparse warnings in various places ps7_init*
- add missing headers
- consolidate code around zynqmp_mmio_read/write
- switch to amd.com email
zynqmp_clk:
- Add handling for gem rx/tsu clocks
zynq_gem:
- Configure mdio clock at run time
zynq:
- Enable fdt overlay support
zynq_sdhci:
- Call dll reset only for ZynqMP SOCs
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZLqHzgAKCRDKSWXLKUoM
IcdEAKCSgy0lMxb1c0adCjpkQR9x63oKbQCdGiioU+W+0moznHdI7+W2UptNt3w=
=Uzn8
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.10-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2023.10-rc1 v2
axi_emac:
- Change return value if RX packet is not ready
cadence_qspi:
- Enable flash reset for Versal NET
dt:
- Various DT syncups with Linux kernel
- SOM - reserved pmufw memory location
fpga:
- Add load event
mtd:
- Add missing dependency for FLASH_CFI_MTD
spi/nand:
- Minor cleanup in Xilinx drivers
versal-net:
- Prioritize boot device in boot_targets
- Wire mini ospi/qspi/emmc configurations
watchdog:
- Use new versal-wwdt property
xilinx:
- fix sparse warnings in various places ps7_init*
- add missing headers
- consolidate code around zynqmp_mmio_read/write
- switch to amd.com email
zynqmp_clk:
- Add handling for gem rx/tsu clocks
zynq_gem:
- Configure mdio clock at run time
zynq:
- Enable fdt overlay support
zynq_sdhci:
- Call dll reset only for ZynqMP SOCs
To sync with the upstream code, removed 'snps,enable_guctl1_resume_quirk'
quirk for usb. This quirk is no more available in linux after the xilinx
release 2022.2.
This functionality is taken care of by the 'snps,resume-hs-terminations'
quirk.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/4b7a132116bf0248cdb558e04de3b06b412c4a0f.1688992653.git.michal.simek@amd.com
Explicitly specify interrupt affinity to avoid HW perfevents
need to guess. This avoids the following error upon linux boot:
armv8-pmu pmu: hw perfevents: no interrupt-affinity property,
guessing.
Reported-by: John Toomey <john.toomey@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c2f55a10cf54c6004f5dfe2ea18bcb4cf04f5723.1688992653.git.michal.simek@amd.com
Linux kernel throws "cacheinfo: Unable to detect cache hierarchy for
CPU 0" warning when booting on zu+ Soc. To fix it add the L2 cache
node and let each CPU point to it.
Reported-by: John Toomey <john.toomey@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c8dfabab12c97922aaad7fa91be0cbc7e4021528.1688992653.git.michal.simek@amd.com
The commit a4180c3696 ("arm64: zynqmp: Add mode-pin GPIO controller DT
node") added usb phy reset over bootmode pins by default on usb0 only.
zcu100 is using usb0 as peripheral and usb1 as host. Unfortunately reset
line is shared for both usb ulpi phys but usb_rst_b is connected to usb5744
hub which is used only in host mode. Especially this chip requires reset to
operate properly that's why better assign gpio reset to usb1 instead of
usb0.
Without this change usb start crashed when runs.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/1ca80ec5bf7a595c03822f3e4e3683298205067a.1688992653.git.michal.simek@amd.com
Extend compatible versions for K24 SOM.
Changes are not affecting SW behavior that's why all versions are
compatible to each other.
Describing all revisions is done by purpose because user space SW is
reading compatible string for logic around DT overlays and bitstreams.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/92eba01ac316e58bd2d3508b0e63bbfafbedbb73.1688992653.git.michal.simek@amd.com
Increase reset assert time for TI SGMII PHY on KR260 CC starting
6.1 kernel. This PHY does not come out of reset with the existing
100us pulse width as per testing on multiple carrier cards. The reset
is driven via a PCA9570 I2C expander. The expander driver was updated
to an upstream version in 6.1 where gpio_chip _set was optimized.
Delays in earlier kernels may have masked this issue. This is a safe
workaround value for assert pulse width before the discussions are
resolved with TI.
Signed-off-by: Harini Katakam <harini.katakam@amd.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/8fb9f17d43a43ef504c9f29006cd686cce8ac98b.1688992653.git.michal.simek@amd.com
Add support for Versal NET mini Octal SPI flash configuration. This runs
from onchip memory, so it has to be compact. Hence only Octal SPI
related settings are enabled.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614121351.21521-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for Versal NET mini Quad SPI flash configuration. This runs
from onchip memory, so it has to be compact. Hence only Quad SPI
related settings are enabled.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614121351.21521-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Enable flash reset functionality for Versal NET platform.
In cadence_qspi.c there is weak function defined for reset, hence remove
the check for config, so that it will work for Versal and Versal NET
platforms.
Add register defines in Versal NET hardware.h for mini U-Boot flash
reset.
Add read_delay initialization for Versal NET also.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614120452.21019-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
PMUFW requires top 1MB of the lower DDR memory reserved for its operation,
this is missing in k26/k24 sm static dts files because of which U-Boot
throws warning messages "efi_free_pool: illegal free" as EFI puts
some code to that space which shouldn't happen.
Signed-off-by: Sharath Kumar Dasari <sharath.kumar.dasari@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/57452d16df2d48593de206bebf877d2c2cfe7bf1.1685966389.git.michal.simek@amd.com
The H616 SoC has support for several types of DRAM: DDR3, LPDDR3,
DDR4 and LPDDR4.
At the moment, the driver only supports DDR3 memory.
Let's extend the driver to support the LPDDR3 memory. All "magic"
values obtained from the boot0.
Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Allwinner H616 SoC supports several types of DRAM memory. To further
integrate other types of memory, we need to add this delimitation.
Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently there is one DRAM parameter struct for the Allwinner H616 DRAM
"driver". It contains many fields that are compile time constants
(set by Kconfig variables), though there are also some fields that are
probed and changed over the runtime of the DRAM initialisation.
Because of this mixture, the compiler cannot properly optimise the code
for size, as it does not consider constant propagation in its full
potential.
Help the compiler out by splitting that structure into two: one that only
contains values known at compile time, and another one where the values
will actually change. The former can then be declared "const", which will
let the compiler fold its values directly into the code using it.
We also add "const" tags for some new "struct dram_config" pointers, to
further increase code optimisation.
To help the compiler optimise the code further, the definition of the
now "const struct dram_para" has to happen at a file-global level, so
move that part out of sunxi_dram_init().
That results in quite some code savings (almost 2KB), and helps to keep
the code small with the LPDDR3 support added later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
There are quite some functions in the Allwinner H616 DRAM "driver", some
of them actually change the parameters in the structure passed to them,
but many are actually not.
To increase the optimisation potential for the code, mark those functions
that just read members of the passed dram_para struct as "const".
This in itself does not decrease the code size, but lays the groundwork
for future changes doing so.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The usage of the C keyword "inline" seems to be a common
misunderstanding: it's a *hint* only, and modern compilers will inline
(or not) functions based on their own judgement and provided compiler
options.
So while marking functions as "inline" does not do much, missing the
"static" keyword will force to compiler to spell out a version of the
function for potential external callers, which actually increases the
code size (though hopefully the linker will drop the function).
Change the "inline" attribute for the mbus_configure_port() functions in
some Allwinner DRAM drivers to "static", so that the explicit version
can actually be dropped from the object file, reducing the code size.
"static inline" has a use case in header files, where it avoids a warning
if a .c file including this header does not use the particular function.
In a .c file itself "static inline" is not useful otherwise, so just use
static here as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
At the moment we use "select" in each Allwinner SoC's Kconfig section to
include the USB PHY driver in the build. This means it cannot be disabled
via Kconfig, although USB is not really a strictly required core
functionality, and a particular board might not even include USB ports.
Rework the Kconfig part by removing the "select" lines for each SoC's
section, and instead letting it default to "y" in the PHY driver section
itself. We use "depends on !" to exclude the few SoCs we don't support
(yet). The Allwinner V3s does not enable USB (PHY) support at the moment,
even though it should work: let the PHY default to "n" to keep the
current behaviour.
Also the MUSB USB driver directly calls some functions from the PHY
driver, so let the former depend on the PHY driver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Sam Edwards <CFSworks@gmail.com>
These boards use SPL in a mkimage entry and apparently access the symbol
containing the image position of U-Boot, but put U-Boot in another
image. This means that binman is unable to fill in the symbol correctly
in the SPL binary.
This doesn't matter at present since mkimage doesn't support symbol
writing. But with the upcoming conversion to a section, it will. So add
a property to disable symbol writing.
Signed-off-by: Simon Glass <sjg@chromium.org>
With sandbox and sandbox64 configurations:
In file included from .../u-boot/include/test/test.h:156,
from .../u-boot/include/test/lib.h:9,
from .../u-boot/test/lib/test_crc8.c:8:
.../u-boot/arch/sandbox/include/asm/test.h: In function ‘sandbox_sdl_set_bpp’:
.../u-boot/arch/sandbox/include/asm/test.h:323:17: error: ‘ENOSYS’ undeclared (first use in this function)
323 | return -ENOSYS;
| ^~~~~~
Per Tom Rini's suggestion:
move that function prototype over to arch/sandbox/include/asm/sdl.h
and make test/dm/video.c include <asm/sdl.h>
Cc: Simon Glass <sjg@chromium.org>
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With gcc-13.1 we get a warning about enum vs int here, so correct the
declaration to match the implementation.
Signed-off-by: Tom Rini <trini@konsulko.com>
When building with gcc-13.1 we see that the prototype for
cvmx_pko3_sq_config_children does not match the declaration. Make these
match and correct a typo in the function's version of the docs that the
prototype did not have, as part of keeping those in-sync.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is more convenient since it does not require a video BIOS. Enable
it for QEMU.
Also drop use of video in SPL for the 64-bit QEMU, since it not needed
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some boards need to access GPIOs to determine which SDRAM is fitted to the
board, for example chromebook_link. Probe this device (if it exists) to
make sure that this works as expected.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add the required tag so that micron memory can be set up correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move from using debug() to log_debug() so that we don't have to use the
__func__ parameter and can access other logging features.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The ACPI tables are special in that they are passed to EFI as a separate
piece, independent of other tables.
Also they can be spread over two areas of memory, e.g. with QEMU we end
up with tables kept in high memory as well.
Add new global_data fields to hold this information and update the bdinfo
command to show the table areas.
Move the rom_table_end variable into the loop that uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The implementation of write_tables() is confusing because it uses the
rom_table_start variable as the address pointer as it progresses.
Rename it to rom_addr to make the code clearer. Move the rom_table_end
variable into the block where it is used.
Also update logging to use the ACPI category, now that it is available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When global_data is relocated, log_head moves in memory, meaning that
the items in that list point to the wrong place.
Disable logging when making the change, then reenable it afterwards, so
that logging works normally.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When video is required in SPL, set this up ready for use. Ignore any
problems since it may be that video is not actually available and we
still want to continue on to U-Boot proper in that case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Print the banner in SPL init only if the spl_board_init() function isn't
enabled. The spl_board_init() function is in the same file, but is called
later, by board_init_r().
This avoids printing two banners, which causes tests to fail.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With qemu-x86_64 we need to run the video BIOS while in 32-bit mode, i.e.
SPL. Add a Kconfig option for this, adjust the Makefile rules and use
CONFIG_IS_ENABLED() where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this leaves the stack at the pre-relocation value. This is not
ideal since we want to have U-Boot running entirely from the top of
memory.
In addition, the new global_data pointer is not actually used, since
the global_data pointer itself is relocated, then the pre-relocation value
is changed, so the effective value (after relocation) does not update.
Adjust the implementation to follow the 32-bit code more closely, with a
trampoline function which is passed the new stack and global_data pointer.
This ensures that the correct values come through even when relocating.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Rather than silently hanging, show an error first. This can happen when
there is something wrong with the video BIOS.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use an assembler implementation as is done for i386, so that the results
are equivalent for i386 and x86_64.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is useful information so show it with the bdinfo command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a comment for this function in the header.
Change the function (and the one after) to use __noreturn to keep
checkpatch happy.
Add docs to board_init_f_r() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The ll_boot_init() check handles the EFI case so we don't need the rest
of the code. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move MTRR-listing code into a common file so it can be used from SPL.
Update the 'mtrr' command to call it.
Use this in SPL just before adjusting the MTRRs, so we can see the state
set up by the board. Only show it when debug is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Allow reading the command line from a zimage, so that it can be recorded
in the bootflow.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a direct interface to booting a zimage, so that bootstd can call it
without going through the command-line interface.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Flushing kernel image after decompression was taking 113 milliseconds
with U-boot 2022.10. With U-boot 2023.01 and 2023.04, flushing
the same amount of memory takes approx 1.5 seconds. With
U-boot 2023.07-rc6, it takes 6.5 seconds.
powerpc flush_cache() function used to call WATCHDOG_RESET() after
flushing every cacheline. At that time WATCHDOG_RESET() was light
so the operation was almost seamless.
But commit 29caf9305b ("cyclic: Use schedule() instead of
WATCHDOG_RESET()") replaced WATCHDOG_RESET() by schedule() and that
started to hurt with U-boot 2022.10.
And in U-boot 2023.07-rc6 that's even worse after
commit 26e8ebcd7c ("watchdog: mpc8xxx: Make it generic").
In the meantime commit 729c1fe656 ("powerpc: introduce
CONFIG_CACHE_FLUSH_WATCHDOG_THRESHOLD") gives us the opportinity to
only call schedule() every given chunk of data instead of every
cacheline. As explained in that commit there is no point in pinging
the watchdog after every cacheline flush, so lets define a sensible
default chunk size of 4k which matches to size of a page on most
powerpc platforms.
With that new default threshold, the culprit flushing performed after
kernel image decompression now takes 85 milliseconds on a powerpc 8xx.
Fixes: 29caf9305b ("cyclic: Use schedule() instead of WATCHDOG_RESET()")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
The only way to create an expo at present is by calling the functions to
create each object. It is useful to have more data-driven approach, where
the objects can be specified in a suitable file format and created from
that. This makes testing easier as well.
Add support for describing an expo in a devicetree node. This allows more
complex tests to be set up, as well as providing an easier format for
users. It also provides a better basis for the upcoming configuration
editor.
Signed-off-by: Simon Glass <sjg@chromium.org>
It looks better if menus have a bit of an inset, rather than be drawn hard
up against the background. Also, menu items look better if they have a bit
of spacing between them.
Add theme options for these and implement the required changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
With recent changes to how sandbox handles reset, closing the window
currently just restarts sandbox.
Use the correct sysreset type to tell it to shut down.
Signed-off-by: Simon Glass <sjg@chromium.org>
The sar-reg0 alias was left over from an earlier iteration of the
patches adding support for this board. Remove the unused alias.
Fixes: 6cc8b5db40 ("arm: mvebu: Add RD-AC5X board")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The x240 and SE240 are a series of L2+ switches from Allied Telesis.
There are a number of them in the range but as far as U-Boot is
concerned all the CPU block components are the same so there's only one
board defined.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Drive CTRL_SLEEP_MOCI# high at boot (SPL) using a GPIO hog, this signal
may be used to control some power-rails on the carrier board, therefore
it should be set to high when the module is booting.
To do this as early as possible is generally a good idea and the issue
was noticed on the Yavia carrier board where it is needed to power the
I2C EEPROM on the carrier board.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drive CTRL_SLEEP_MOCI# high at boot (SPL) using a GPIO hog, this signal
may be used to control some power-rails on the carrier board, therefore
it should be set to high when the module is booting.
To do this as early as possible is generally a good idea and the issue
was noticed on the Yavia carrier board where it is needed to power the
I2C EEPROM on the carrier board.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The USB Power domains should not have been removed as it causes
the board to hang if the USB is started.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Several changes have been made to the device tree
in the kernel, so update that as well as the
corresponding imx8mp-u-boot.dtsi files to prevent
breaking the booting.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
For SOM with the EC configuration, the ethernet PHY is located on the
SOM itself, and connected to the CPU ethernet controller. It has a
reset line controlled via GPIO1_IO9. In this configuration, the PHY
located on the carrier board is not connected to anything and is
therefore not used.
For SOM without EC configuration, the ethernet PHY on the carrier
board is connected to the CPU ethernet controller. It has a reset line
controlled via the GPIO expander PCA9534_IO5.
The hardware configuration (EC) is determined at runtime by
reading from the SOM EEPROM.
To support both hardware configurations (EC and non-EC), adjust/fix
the PHY reset gpios according to the hardware configuration
read at runtime from the SOM EEPROM. This adjustement is done in
U-Boot (OF_BOARD_FIXUP) and kernel (OF_BOARD_SETUP) device trees.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Bitwise operations on signed integers are not defined,
replace them with per-call checks.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
In order to enable HAB, FSL_CAAM, ARCH_MISC_INIT and
SPL_CRYPTO should be enabled in Kconfig like other i.MX8M
boards.
This also needs to occur in the SPL so enable CONFIG_SPL_BOARD_INIT and
add a void spl_board_init function which calls arch_misc_init to probe
the CAAM driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
add support for SHA-256 secure hash algorithm using the ARM v8
SHA-256 instructions for verifying image hash.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Abstract common interfaces for AHAB authentication operations.
Then share some common codes for AHAB and SPL container authentication
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If the container has image which conflicts with
spl_get_load_buffer address, there are processing failures.
Use malloc instead of spl_get_load_buffer.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Nitin Garg <nitin.garg@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
1. Implement bootaux for the M4 boot on i.MX8QM and QXP. Users need to download
M4 image to any DDR address first. Then use the
"bootaux <M4 download DDR address> [M4 core id]" to boot CM4_0
or CM4_1, the default core id is 0 for CM4_0.
Since current M4 only supports running in TCM. The bootaux will copy
the M4 image from DDR to its TCML.
2. Implment bootaux for HIFI on QXP
command: bootaux 0x81000000 1
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The bootaux uses ulong to read private data and write to M4 TCM,
this cause problem on ARM64 platform where the ulong is 8bytes.
Fix it by using u32 to replace ulong.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current bootaux supports i.MX8M and i.MX93, but the name "_M4_"
implies that the SoCs have Cortex-M4. Actually i.MX8MM/Q use Cortex-M4,
i.MX8MN/P use Cortex-M7, i.MX93 use Cortex-M33, so use "_MCU_" in place
of "_M4_" to simplify the naming.
Signed-off-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the support for loading image from secondary container set on
iMX8QM B0, iMX8QXP C0.
Using the SCFW API to get container set index, if it is the secondary
boot, get the offset from fuse and apply to offset of current container
set beginning for loading.
Also override the emmc boot partition to check secondary boot and switch
to the other boot part.
This patch is modified from NXP downstream:
imx8: Fix the fuse used by secondary container offset
imx: container: Skip container set check for ROM API
imx8: spl: Support booting from secondary container set
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Checking container header tag and version is wrong, it causes to fail
to bypass invalid container
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix below coverity issues caused by get_idx function where "-1" is
compared with uint8_t "element"
343336 Unsigned compared with neg
343337 Operands don't affect result
Additional, this function returns "-1" will cause overflow to
event string array.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On the imx8ulp A1 SoC, the ELE RNG needs to be manually started.
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity (CID 21143558).
When tee_shm_register returns failure, the shm_input pointer is
invalid, should not free it. Same issue also exists on registering
shm_output.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add two ELE API: ele_return_lifecycle_update and ele_write_secure_fuse
Add two cmd: ahab_return_lifecycle and ahab_sec_fuse_prog
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix build warning:
warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3
has type ‘u64’ {aka ‘long long unsigned int’} [-Wformat=]
printf("can't find memreg for image %d load address 0x%x, error %d\n",
warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but
argument 3 has type ‘sc_faddr_t’ {aka ‘long long unsigned int’} [-Wformat=]
debug("memreg %u 0x%lx -- 0x%lx\n", mr, start, end);
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Per NXP requirement, we rename all the NXP EdgeLock Secure Enclave
code including comment, folder and API name to ELE to align.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make sure the serial driver is initialized before relocation by tagging
the serial nodes with "bootph-all". Add these u-boot specific properties
to an *-u-boot.dtsi file.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the serial node descriptions similar to Linux v6.4 for the
t1024rdb board and its dependencies.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make sure the serial driver is initialized before relocation by tagging
the serial nodes with "bootph-all". Add these u-boot specific properties
to an *-u-boot.dtsi file.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the serial node descriptions similar to Linux v6.4 for the
t1042d4rdb board and its dependencies.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make sure the serial driver is initialized before relocation by tagging
the serial nodes with "bootph-all". Add these u-boot specific properties
to an *-u-boot.dtsi file.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the serial node descriptions similar to Linux v6.4 for the t4240rdb
board and its dependencies.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make sure the serial driver is initialized before relocation by tagging
the serial nodes with "bootph-all". Add these u-boot specific properties
to an *-u-boot.dtsi file.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the serial node descriptions similar to Linux v6.4 for the t2080rdb
board and its dependencies.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The NF_CLK for the AC5 SoC runs at 400MHz. There's no strapping
or gating require so just add a mvebu_get_nand_clock() that
returns this value.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The AC5/AC5X SoC has a NAND flash controller. Add this to the
SoC device tree.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Update the Thecus N2350 DTS to conform with latest device-tree binding
and styles.
- Correct typo in mdio node.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
