Add SPL_DM_REGULATOR configs for palmas/lp873x/lp87565. These were missing
and the Makefile already assumes them to be defined. Add the corresponding
SPL config options. This enables the regulator support in SPL.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Add SPL_PMIC configs for palmas/lp873x/lp87565. These were missing
and the Makefile already assumes them to be defined. Add the corresponding
SPL config options. This enables the pmics in SPL.
Signed-off-by: Keerthy <j-keerthy@ti.com>
This patch solves the following warnings:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
drivers/power/regulator/stm32-vrefbuf.c: In function 'stm32_vrefbuf_set_value':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (uV == stm32_vrefbuf_voltages[i]) {
^~
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Adds support for SYSRESET_POWER_OFF = PMIC power off used by command
power off and introduced by commit 751fed426f ("sysreset: Add a way
to find the last reset").
The driver use SYSRESET_POWER for the PMIC-level power cycle, with restart.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
https://source.codeaurora.org/external/imx/uboot-imx
cherry picked, styled and merged commits:
- MLK-18387 pmic: Add pmic driver for BD71837: e9a3bec2e95a
- MLK-18590 pmic: bd71837: Change to use new fdt API: acdc5c297a96
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The code that sets a regulator by looking up the voltage in a table had
an off by one error. vsel_mask is a bitmask, not the number of table
entries, so a vsel_mask value of 0x7 indicates there are 8, not 7,
entries in the table.
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Add functions to read/update the non volatile memory of STPMIC1
(8 bytes-register at 0xF8 address) and allow access
with fuse command (bank=1, word > 0xF8).
For example:
STM32MP> fuse read 1 0xf8 8
Reading bank 1:
Word 0x000000f8: 000000ee 00000092 000000c0 00000002
Word 0x000000fc: 000000f2 00000080 00000002 00000033
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Alignment with STPMIC1 datasheet
s/MAIN_CONTROL_REG/MAIN_CR/g
s/MASK_RESET_BUCK/BUCKS_MRST_CR/g
s/MASK_RESET_LDOS/LDOS_MRST_CR/g
s/BUCKX_CTRL_REG/BUCKX_MAIN_CR/g
s/VREF_CTRL_REG/REFDDR_MAIN_CR/g
s/LDOX_CTRL_REG/LDOX_MAIN_CR/g
s/USB_CTRL_REG/BST_SW_CR/g
s/STPMIC1_NVM_USER_STATUS_REG/STPMIC1_NVM_SR/g
s/STPMIC1_NVM_USER_CONTROL_REG/STPMIC1_NVM_CR/g
and update all the associated defines.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Alignment with kernel driver name & binding
introduced by https://patchwork.kernel.org/cover/10761943/
to use the final marketing name = STPMIC1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Prepare file modification for kernel alignment and
rename driver to stpmic1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
SW impact for Rev 1.2 of STPMIC1 in U-Boot:
Buck converters output voltage change for Buck1
=> Vdd min 0,725 to max 1,5V instead of 0.6V to 1.35V
(see STPMIC1 datasheet / chapter 5.3 Buck converters)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As per recent TRM[1], PBIAS cell on dra7 devices supports
3.3v and not 3.0v as documented earlier.
Update PBIAS regulator max voltage and the voltage written
in the driver to reflect this.
[1] http://www.ti.com/lit/pdf/sprui30
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
According to datasheet, the output on LDO regulators will start
appearing after 10-15 us.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Changing voltage and enabling regulator might require delays so the
regulator stabilizes at expected level.
Add support for "regulator-ramp-delay" binding which can introduce
required time to both enabling the regulator and to changing the
voltage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Fix typo in axp_set_dldo() so that it correctly uses AXP818_DLDO1_CTRL
register to configure the voltage instead of setting AXP818_ELDO1_CTRL
register which is obviously incorrect.
Signed-off-by: Ondřej Jirman <megous@megous.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
regulator_set_enable() api throws an error in the following three cases:
- when requested to disable an always-on regulator
- when set_enable() ops not provided by regulator driver
- when enabling is actually failed.(Error returned by the regulator driver)
Sometimes consumer drivers doesn't want to track the first two scenarios
and just need to worry about the case where enabling is actually failed.
But it is also a good practice to have an error value returned in the
first two cases.
So introduce an api regulator_set_enable_if_allowed() which ignores the
first two error cases and returns an error as given by regulator driver.
Consumer drivers can use this api need not worry about the first two
error conditions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit e17e0ceb83.
It is advised to return an error when trying to disable an always-on
regulator and let the consumer driver handle the error if needed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The OMAP36 and DM37 TRM state to disable extneded drain IO before
changing the PBIAS. This patch does this before pmic writes if
the CONFIG_MMC_OMAP36XX_PINS flag is set and the cpu family is
omap36xx
Signed-off-by: Adam Ford <aford173@gmail.com>
MESON_GX_VPU_POWER_DOMAIN should depend on POWER_DOMAIN.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This patch allows to enable the PWM regulator driver
independent for U-Boot and SPL.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
commit 4f86a724e8 ("power: regulator: denied disable on always-on
regulator") throws an error when requested to disable an always-on
regulator. It is right that an always-on regulator should not be
attempted to be disabled. But at the same time regulator framework
should not return an error when such request is received. Instead
it should just return success without attempting to disable the
specified regulator. This is because the requesting driver will
not have the idea if the regulator is always-on or not. The
requesting driver will always try to enable/disable regulator as
per the required flow. So it is upto regulator framework to not
break such scenarios.
Fixes: 4f86a724e8 ("power: regulator: denied disable on always-on regulator")
Reported-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDiw9AAoJECaAFcEOcohNEa8H/RBWLbVQjHPXf6EjchXgVcSs
Gc+g2QmKZbN21XebfzBpCuZj62NROTWUcrPtor17yEBiMM1xPfe1vC7qtbkR6USj
VTt1JHeyGx3XafkkUpeps382YPfuaNqtabjwZaXlmeE4/VLbXQPE7x4tC4fdWus4
9K3OGQgRNFirn+RIZ7dQWtCby82PEC3cHkPc/n82cVHofcDsgKYK9mPpfcCn/gWF
A4Fa9cx4pjeaMrBHKjcByCiFmwYBPc97Hqzz64oHOdQP0g3h04ko+2w5DdwdeHVV
jKNcvkHESF4m1RGjrTbLEhy1f5UuOfcA1ise/cDX4pjXlBdwxHmvqT5vsE0MQzI=
=5sHL
-----END PGP SIGNATURE-----
Merge tag 'for-master-20181210' of git://git.denx.de/u-boot-rockchip
Improvements:
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
This adds a driver for the FAN53555 family of regulators and wraps it
in a PMIC implementation.
While these devices support a 'normal' and 'suspend' mode (controlled
via an external pin) to switch between two programmable voltages, this
incarnation of the driver assumes that the device is always operating
in 'normal' mode.
Only setting/reading the programmed voltage is supported at this time
and the following device functionality remains unsupported:
- switching the selected voltage (via a GPIO)
- disabling the voltage output via software-control
This matches the functionality of the Linux driver.
Tested on a RK3399-Q7 (with 'option 5' devices): setting voltages from
the U-Boot shell and verifying output voltages on the board.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Those driver are not DM drivers per se (not using the PMIC/regulator
framework) and are using the legacy I2C API. Make them compatible with
the DM_I2C API.
This impacts the following drivers:
- palmas (used by am57xx/dra7xx evms)
- tps65218 (used by am43xx evms)
- tps65217 and tps65910 (used by am335x evms and am335x boneblack vboot)
- twl4030 (used by omap3_logicpd)
- tps65217 (used by brppt1)
- twl6030
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Some boards feature a capacitance on LDO3's output that is too large,
causing inrush currents which as a result, shut down the AXP209. This
has been reported before, without knowing the actual cause.
A fix appeared to be done with
commit 0e6e34ac8d ("sunxi: Olimex A20 boards: Enable LDO3 and LDO4 regulators").
The description there is a bit misleading, the kernel does not hang
during AXP209 initialization, the PMIC shuts down, causing voltages to
drop and thus the whole system freezes.
While the AXP209 does have the ability to ramp up the voltage slowly, to
reduce these inrush currents, the voltage rate control (VRC) however is
not applicable when switching on the LDO3 output. Only when going from
an enabled lower voltage setting, to a higher voltage setting is the VRC
in effect.
To work around this problem, we set LDO3 to the lowest possible setting
of 0.7 V if it was not yet enabled, and then let the VRC (if enabled) do
its thing. It should be noted, that for some undocumented reason, there
is a short delay needed between setting the LDO3 voltage register and
enabling the power. One would expect that this delay ought to be just
after enabling the output power at 0.7 V, but this did not work.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AXP209 LDO3 regulator supports voltage rate control, or can set a
slew rate.
This allows for the power to gradually rise up to the desired voltage,
instead of spiking up as fast as possible. Reason to have this can be
to reduce the inrush currents for example.
There are 3 slopes to choose from, the default, 'none' is a voltage rise
of 0.0167 V/uS, a 1.6 mV/uS and a 0.8 mV/uS voltage rise.
In ideal world (where vendors follow the recommended design guidelines)
this setting should not be enabled by default. Unless of course AXP209
crashes instead of reporting overcurrent condition as it normally should
do in this case.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AXP209 has a few 'magisc-ish' values that are better served with
clear defines.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Use a define for the chip version mask on the axp209.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Don't disable regulator which are tagged as "regulator-always-on" in DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jack Mitchell <jack@embed.me.uk>
Tested-by: Jack Mitchell <jack@embed.me.uk>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Richard Röjfors <richard@puffinpack.se>
Tested-by: Richard Röjfors <richard@puffinpack.se>
Reviewed-by: Felix Brack <fb@ltec.ch>
Tested-by: Felix Brack <fb@ltec.ch>
There is a newline missing from quite a few printf() strings in these pmic
files. Fix them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This adds a power domain driver for the Mediatek SCPSYS unit.
The System Control Processor System (SCPSYS) has several power
management related tasks in the system. The tasks include thermal
measurement, dynamic voltage frequency scaling (DVFS), interrupt
filter and lowlevel sleep control. The System Power Manager (SPM)
inside the SCPSYS is for the MTCMOS power domain control.
For now this driver only adds power domain support.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Makefile already tests for SPL_DM_REGULATOR_GPIO, but Kconfig
does not provide it. This adds SPL_DM_REGULATOR_GPIO to Kconfig.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Complete in the drivers directory the work started with
commit 83d290c56f ("SPDX: Convert all of our single
license tags to Linux Kernel style").
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add the power domain DM driver for i.MX8, that it depends on the DTB
power domain trees to generate the power domain provider devices. Users
need to add power domain trees with property "compatible = "nxp,imx8-pd";"
When power on a PD device, the driver will power on its ancestor PD
devices in power domain tree.
When power off a PD device, the driver will check its child PD devices
first. Only if all child PD devices are off, then power off the current PD
device. Then the driver checks sibling PD devices. If sibling PD devices
are off, then it will power off parent PD device.
There is no counter maintained in this driver, but a state to hold current
on/off state. So the request and free functions are empty.
The power domain implementation in i.MX8 DTB set the "#power-domain-cells"
to 0, so there is no ID binding with each PD device. We don't use "id"
variable in struct power_domain. At the same time, we have to set of_xlate
to empty to bypass standard of_xlate in uclass driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The driver was developed with references for more than just
dra7, but never included. At least for omap3, this appears
to be functional.
Signed-off-by: Adam Ford <aford173@gmail.com>
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a power domain driver that communicates to the system
controller over the TI SCI protocol for performing power management of
various devices present on the SoC. Various power domain functionalities
are achieved by the means of different TI SCI device operations provided
by the TI SCI framework.
This code is loosely based on the drivers/soc/ti/ti_sci_pm_domains.c
driver of the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
There are cases where there are more than one power domain
attached to the device inorder to get the device functional.
So add support for enabling power domain based on the index.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The Amlogic Meson SoCs embeds a specific Power Domain dedicated to the
Video Processing Unit.
This patch implements support for this power domain in preparation of the
future support for the Video display support in U-Boot.
This driver will depend on changes in the clock driver to handle the setup
of the VPU and VAPB clocks configured from DT using assigned-clocks entries.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add u-boot,off-on-delay-us for fixed regulator.
Depends on board design, the gpio regulator sometimes
connects with a big capacitance. When need to off, then
on the regulator, if there is no enough delay,
the voltage does not drop to 0, so introduce this
property to handle such case.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add CONFIG_SPL_POWER_DOMAIN config entry.
Build drivers/power/domain if this config is selected.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove additional trailing whitespaces in prompt reported by kconfiglib:
warning: DM_PMIC_SANDBOX (defined at drivers/power/pmic/Kconfig:133) has
leading or trailing whitespace in its prompt
warning: <choice> (defined at dts/Kconfig:204) has leading or trailing
whitespace in its prompt
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Felix Brack <fb@ltec.ch>
This patch adds a delay when regulators are disabled.
This delay is set to 5 ms to cover all use cases.
The worst use case actually seen is during a SD card power cycle.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The PFUZE3000 uses registers addresses up to 0xff.
The DM pfuze100 driver supports both pfuze100 and pfuze3000. Allow it
to use the device type to return the correct number of registers.
Also rename the too generic PMIC_NUM_OF_REGS enumeration value for
pfuze3000 to match the other "PFUZE3000_" prefixed enumerations and the
pfuze100 enumeration value PFUZE100_NUM_OF_REGS.
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This change enables support for MC34708 PMIC in sandbox. Now we can
emulate the I2C transfers larger than 1 byte.
Notable changes for this driver:
- From now on the register number is not equal to index in the buffer,
which emulates the PMIC registers
- The PMIC register's pool is now dynamically allocated up till
64 regs * 3 bytes each = 192 B
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support for MC34708 PMIC, to be used with driver model
(DM).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit provides support for transmissions larger than 1 byte for
PMIC devices used with DM (e.g. MC34708 from NXP).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The struct uc_pmic_priv's trans_len field stores the number of types to
be transmitted per PMIC transfer.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix ldo_get_enable() and ldo_set_enable() functions for LDOs with an
index > 7. Turns out there are actually two separate AS3722_LDO_CONTROL
registers AS3722_LDO_CONTROL0 and AS3722_LDO_CONTROL1. Actually make use
of both. While at it also actually use the enable parameter of the
ldo_set_enable() function which now truly allows disabling as opposed to
only enabling LDOs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add regulator driver for STM32 voltage reference buffer which can be
used as voltage reference for ADCs, DACs and external components through
dedicated VREF+ pin.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add regulator bindings to get access to regulator managed
by drivers/power/regulator/stpmu1.c regulator driver.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Enable support for the regulator functions of the STPMU1X PMIC. The
driver implements get/set api for the various BUCKS and LDOs supported
by the PMIC device. This driver is controlled by a device tree node
which includes voltage limits.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
max77686 pmic is supporting with max77686.c under pmic/ and regulator/
direnctroy. Remove pmic_max77686.c what didn't use anywhere.
Instead, enable CONFIG_DM_REGULATOR_MAX77686 and
CONFIG_DM_PMIC_MAX77686.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document. Note that parenthesis are
allowed so when they were used before we continue to use them.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
We should not evaluate the value of reg before its value is set.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver implements register read/write operations for STPMU1.
The STPMU1 PMIC provides 4 BUCKs, 6 LDOs, 1 VREF
and 2 power switches. It is accessed via an I2C interface.
This device is used with STM32MP1 SoCs.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add simple and meaningful kconfig option for pmic_bus.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add the probe function to support the s2mps11 regulator driver.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
exynos5422 has the s2mps11 PMIC.
s2mps11 pmic has the 10-BUCK and 38-LDO regulators.
Each IP and devices in exynos5422 can be controlled by each regulators.
This patch is support for s2mps11 regulator driver.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
In order to discard this code when unused in SPL we need to guard the
command with a check for CONFIG_SPL_BUILD and we rearrange the code
slightly to make this cleaner.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The patch replaces the former error() by the new pr_err().
This makes the TPS65910 driver conform to Masahiro's patch
'treewide:replace with error() with pr_err()' introduced
October 2017.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Simon Glass <sjg@chromium.org>
Texas Instrument's TPS65910 PMIC contains 3 buck DC-DC converts, one
boost DC-DC converter and 8 LDOs. This patch implements driver model
support for the TPS65910 PMIC and its regulators making the get/set
API for regulator value/enable available.
This patch depends on the patch "am33xx: Add a function to query MPU
voltage in uV" to build correctly. For boards relying on the DT
include file tps65910.dtsi the v3 patch "power: extend prefix match
to regulator-name property" and an appropriate regulator naming is
also required.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch extends pmic_bind_children prefix matching. In addition to
the node name the property regulator-name is used while trying to match
prefixes. This allows assigning different drivers to regulator nodes
named regulator@1 and regulator@10 for example.
I have discarded the idea of using other properties then regulator-name
as I do not see any benefit in using property compatible or even
regulator-compatible. Of course I am open to change this if there are
good reasons to do so.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Simon Glass <sjg@chromium.org>
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
The Makefile already tests for SPL_DM_REGULATOR_FIXED, but Kconfig
does not provide it. This adds SPL_DM_REGULATOR_FIXED to Kconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the TI SOCs a PBIAS cell exists to provide a bias voltage to the MMC1
IO cells. Without this bias voltage these I/O cells can not function
properly. The PBIAS cell is controlled by software.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove header file includes that have been left over after the
conversion to livetree-support.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add a convenience macro to iterate over subnodes of a node. Make use of
this where appropriate in the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is not necessary that ldo1 is used to power on mmc.
So, add support for passing ldo registers for powering on mmc.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some LDOs have a bypass capability. Make sure that the bypass is disabled
when is the LDO is enabled (otherwise the voltage can't be changed).
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Modify palmas_mmc1_poweron_ldo() API to set the voltage based on the
voltage parameter passed as argument instead of always setting it to
3.0V. This allows MMC1 to set the LDO1 regulator voltage to 3.3V or 1.8V.
1.8V is required to add support for UHS mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Convert this PMIC driver to driver model and fix up other users. The
regulator and GPIO functions are now handled by separate drivers.
Update nyan-big to work correct. Three boards will need to be updated by
the maintainers: apalis-tk1, cei-tk1-som. Also the TODO in the code re
as3722_sd_set_voltage() needs to be completed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
This pmic includes GPIOs which should have their own driver. Add
a driver to support these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
This pmic includes regulators which should have their own driver. Add
a driver to support these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
The regulator_enable() should be called from upper layer like
regulators_enable_boot_on(), remove it from pwm regulator driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[fixed up typo in commit message:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The rkpwm reg order has fixed by below patch:
e3ef41d rockchip: pwm: fix the register layout for the PWM controller
We need to correct the parameter order for pwm_set_config() to make
the pwm regulator works correctly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
get_enable should be able to return error values. Hence change
the return type to integer.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
get_enable should be able to return error values. Hence change
the return type to integer.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
get_enable should be able to return error values. Hence change
the return type to integer.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
get_enable should be able to return error values. Hence change
the return type to integer.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
get_enable should be able to return error values. Hence change
the return type to integer.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
get_enable should be able to return error values. Hence change
the return type to integer.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
get_enable should be able to return error values. Hence change
the return type to integer.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
get_enable should be able to return error values. Hence change
the return type to integer.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
get_enable should be able to return error values. Hence change
the return type to integer.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
get_enable should be able to return error values. Hence change
the return type to integer.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
get_enable should be able to return error values. Hence change
the return type to integer.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK818 PMIC contains a charger. Add very basic charger functionality
to be able to regulate the USB input current and charger shutdown limits.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enabling CONFIG_SPL_POWER_SUPPORT will cause a compiler warning:
‘get_ldo_reg’ defined but not used [-Wunused-function]
Let's wrap get_ldo_reg(), rk808_ldo and rk818_ldo with ENABLE_DRIVER
which is only set for non SPL builds.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This file does not report a few possible errors and one message is missing
a newline. Fix these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The driver provides regulator set/get voltage
enable/disable functions for lp87565 family of PMICs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support to bind the regulators/child nodes with the pmic.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Some boards like am437x-gp-evm require dcdc3 also to be configured
as it feeds on to ddr. Hence add the capability as well.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Since priv->init_voltage is an unsigned integer it can never be
negative. So the current code fails to detect a missing
'regulator-init-microvolt' property and instead misconfigures the
PWM device. Fix this by making the relevant members of
'struct pwm_regulator_info' signed integers.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Till now get_ldo_reg did a return &rk808_ldo[num - 1]; to return
the ldo register offset but didn't take into account that its
calling functions already created the ldo as ldo = dev->driver_data - 1.
This resulted in the setting for ldo8 writing to the register of ldo7
and so on. So fix this and get the correct ldo register data.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
The rk8xx_priv structure need to allocate for driver, or else
it will cause data abort when CPU access it.
This is a bug fix for below patch set:
https://www.mail-archive.com/u-boot@lists.denx.de/msg247345.html
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
This PMIC driver (power and GPIO) is used by the sandbox SPMI tests.
Update the drivers to support a live device tree so that the tests pass.
Signed-off-by: Simon Glass <sjg@chromium.org>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently while setting the vsel value for dcdc1 and dcdc2
the driver is wrongly masking the entire 8 bits in the process
clearing PFM (bit7) field as well. Hence describe an appropriate
mask for vsel field and modify only those bits in the vsel
mask.
Source: http://www.ti.com/lit/ds/symlink/tps65218.pdf
Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixes: 86db550b38 ("power: Add support for the TPS65218 PMIC")
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Inside of
max77686_buck_volt2hex/max77686_buck_hex2volt/max77686_ldo_volt2hex we
check that the value we calculate is >= 0 however we declare 'hex' as
unsigned int making these always true. Mark these as 'int' instead. We
also move hex_max to int as they are constants that are 0x3f/0xff.
Given that the above functions are marked as returning an int, make the
variables we assign their return value to also be int to be able to
catch the error condition now. Reported by clang-3.8.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that CMD_POWEROFF can turn off the twl4030, let's imply that
just incase someone wants to disable it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds a new firefly-rk3399 board, MIPI support for rk3399 and
rk3288, rk818 pmic support, mkimage improvements for rockchip and a few
other things.
Since this driver can be used for rk8xx series pmic,
let's rename rk808 to rk8xx, to make it clear.
Configs parts are done by sed -i "s/RK808/RK8XX/g" `grep RK808 -lr ./`
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Add support for the rk818 regulator. The regulator module consists
of 4 DCDCs, 9 LDOs, 1 switch and 1 BOOST converter which is used to
power OTG and HDMI5V.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK818 chip is a Power Management IC (PMIC) for multimedia and handheld
devices.
For boards use rk818, the input current should be set in the early stage, before
ddr initialization.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Both RK808 and RK818 chips are using a similar register map,
so we can reuse them.
I have also add reg prefix to exist registers, to keep them same style.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The latest kernel PWM drivers enable the polarity settings. When system
run from U-Boot to kerenl, if there are differences in polarity set or
duty cycle, the PMW will re-init:
close -> set polarity and duty cycle -> enable the PWM.
The power supply controled by pwm regulator may have voltage shaking,
which lead to the system not stable.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
As requested, I added the CONFIG_TWL4030_POWER to Kconfig and made it
the implied default when selecting OMAP34XX as a platform.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the addition of twl4030_power_off(), let's allow the 'poweroff' command
to run this function when CONFIG_CMD_POWEROFF is enabled.
Tested on a DM3730 with twl4030 PMIC.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Driver for that regulator is used only in SPL and it uses old I2C
interface. If we want to use DM I2C in U-Boot proper, compilation of
this driver has to be limited only to SPL.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 SoC uses the AXP221s in I2C mode to supply power.
Some regulator's common usages have changed, and also the recommended
voltage for existing usages have changed. Update the defaults to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The execution flow is currently like this for aldo_num == 1 or 2:
int axp_set_aldo(int aldo_num, unsigned int mvolt)
{
...
if (mvolt == 0)
return pmic_bus_clrbits(AXP809_OUTPUT_CTRL1,
AXP809_OUTPUT_CTRL1_ALDO1_EN << (aldo_num - 1));
...
return pmic_bus_clrbits(AXP809_OUTPUT_CTRL1,
AXP809_OUTPUT_CTRL1_ALDO1_EN << (aldo_num - 1));
}
I.e. aldo1 and aldo2 will always be disabled. This patch fixes it by
setting (rather than clearing) the enable bit when mvolt != 0.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Fixes: 795857df41 ("sunxi: power: add AXP809 support")
Add the max8997 controller for Driver model.
Exynos4210 is using max8997 pmic controller.
(pmic_max8997.c should be deprecated.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The array indices used currently are dispalaced by 1 for
SMPS6 through SMPS10 in the respective places of voltage and ctrl
arrays hence fix the same as to assign the right voltage and ctrl
registers.
Signed-off-by: Keerthy <j-keerthy@ti.com>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds a simple pmic driver for the mc34vr500 pmic which
is used in conjunction with the fsl T1 and LS1 series SoC.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The variable ret was added but never set as we did not make calls to
other functions that we needed to check the return value on.
Fixes: 505cf4750a ("power: change from meaningless value to error number")
Signed-off-by: Tom Rini <trini@konsulko.com>
'-1' is absolutely meaningless value.
This patch changed from meaningless value to error number.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to handle enable-active-high DT property. This property is
used to drive the gpio controlling fixed regulator as active high when
claiming gpio line.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add the max8998 controller for Driver model.
Samsung S5P series are using max8998 pmic controller.
In future, it should be supported the regulator framework.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Palmas driver assumes it is always TPS659xx regulator on all DRA7xx based
boards to enable mmc regulator. This is not true always like in case of
DRA71x-evm. So get this information based on the board.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Delete omap4_vmmc_pbias_config from omap_hsmmc.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_AM57XX is just an unnecessary macro that is redundant given So,
remove the same instead of spreading through out the u-boot source
code and getting in the way to maintain common code for DRA7x family.
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently the specific set ops functions are directly
called without any check for min/max current limits for a regulator.
Check for them and proceed.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixed checking of current limits:
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently the specific set ops functions are directly
called without any check for voltage limits for a regulator.
Check for them and proceed.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fixed checking of voltate limits:
Signed-off-by: Simon Glass <sjg@chromium.org>
In case we want to force a particular value on a regulator
irrespective of the min/max constraints for testing purposes
one can call regulator_set_value_force function.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit a85362fb3e refactored the code
but the register read ended up in the wrong if branch.
Currently, the else branch checks a variable which is always 0.
Signed-off-by: Nicolae Rosia <nicolae_rosia@mentor.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The signature for this macro has changed. Bring in the upstream version and
adjust U-Boot's usages to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update to drivers/power/pmic/palmas.c:
Signed-off-by: Keerthy <j-keerthy@ti.com>
Change-Id: I6cc9021339bfe686f9df21d61a1095ca2b3776e8
The driver provides regulator set/get voltage
enable/disable functions for lp873x family of PMICs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver provides regulator set/get voltage
enable/disable functions for palmas family of PMICs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write funtions to access pmic
registers.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for gpio regulators. As of now this driver caters
to gpio regulators with one gpio. Supports setting voltage values to gpio
regulators and retrieving the values.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
According to the binding documentation the fixed regulator enable GPIO
is optional. However so far registration thereof failed if no enable
GPIO was specified. Fix this by making it entirely optional whether an
enable GPIO is used.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add device model enabled PMIC driver for Ricoh RN5T567 PMIC used
on Colibri iMX7.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
add driver support for pwm regulator.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
When cold-booting the ldoio0/1 regulators are always off / the
gpios are always at tristate. But when re-booting from android these
are sometimes on. Disable them at axp_init time (iow as early as possible)
to remove this difference between a cold boot and a reboot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When enabling a fixed regulator, it may take some time to rise to the
correct voltage. If we do not delay here then subsequent operations
will fail.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In Tegra186, SoC power domains are manipulated using IPC requests to
the BPMP (Boot and Power Management Processor). This change implements a
driver that does that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The voltage and control registers need to be looked up from the value in
driver_data. Adjust the get_value and get_enable functions to match the
corresponding set_* functions.
Signed-off-by: John Keeping <john@metanate.com>
Acked-by: Simon Glass <sjg@chromium.org>
Linux stopped the use of keyword 'boolean' in Kconfig.
Refer to commit 6341e62b212a2541efb0160c470e90bd226d5496 ("kconfig:
use bool instead of boolean for type definition attributes")
in Linux Kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Many SoCs allow power to be applied to or removed from portions of the SoC
(power domains). This may be used to save power. This API provides the
means to control such power management hardware.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quite a few places have a bind() method which just calls dm_scan_fdt_dev().
We may as well call dm_scan_fdt_dev() directly. Update the code to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The A80 uses the AXP809 as its primary PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Adds poweroff support for axp818 pmic.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The AXP818 has a switchable output, SW. This is commonly used for
controlling power to the LCD backlight.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Description said eldo2 instead of fldo2, a copy-paste error.
Fixes: 38491d9c65 ("power: axp818: Add support for FLDOs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The ELDO enable bits and registers are contiguous for axp221. Instead
of a switch case testing against the index, just use the index to shift
the bit or register offset.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
If get_dev_addr fails it will return FDT_ADDR_T_NONE and:
>>> "priv->usid == 4294967295U" is always false regardless of the values of its operands. This occurs as the logical operand of if.
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reported-by: Coverity (CID: 143914)
Signed-off-by: Tom Rini <trini@konsulko.com>
This PMIC is connected on SPMI bus so needs SPMI support enabled.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The Allwinner A64 SoC is used in the Pine64. This patch adds
all bits necessary to compile U-Boot for it running in AArch64
mode.
Unfortunately SPL is not ready yet due to legal problems, so
we need to boot using the binary boot0 for now.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: remove SPL code, move to AArch64]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The FLDOs on AXP818 PMIC normally provide power to CPUS and USB HSIC PHY
on the A83T/H8.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
DCDC5 is designed to supply VCC-DRAM, which is normally 1.5V for DDR3,
1.35V for DDR3L, and 1.2V for LPDDR3.
Also remove CONFIG_AXP_DCDC5_VOLT from h8_homlet_v2_defconfig.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The TWL6030 power driver is only built when CONFIG_TWL6030_POWER is selected,
thus there is no reason to wrap the code with ifdef.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
When booting from USB, the bootrom sets the VUSB_IN_PMID bit of the MISC2
register of the TWL6030. However, U-Boot sets the VUSB_IN_VSYS bit to enable
VBUS input. As both bits are contradictory, enabling both disables the input,
according to the TWL6030 TRM.
Thus, we need to clear the VUSB_IN_PMID bit in case of an USB boot (which could
just as well be a memory boot after USB timed out).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Not every device has multiple MMC slots available, so it makes sense to enable
only the required LDOs for the available slots. Generic code in omap_hsmmc will
enable both VMMC and VAUX1, in doubt.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This enables the VAUX1 supply, used for eMMC power in standard configurations.
Its voltage is determined by the value of the BOOT2 pin of the TWL6030.
Note that the TWL6030 might already have enabled this regulator at startup
(depending on the value of the BOOT3 pin of the TWL6030), according to the
TWL6030 datasheet.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This makes the twl6030 mmc and usb-related power registers and values
definitions more explicit and clear and adds prefixes to them.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Add the following functions:
tps65218_reg_read() for accessing redisters
tps65218_toggle_fseal() for toggling the fseal bit
tps65218_lock_fsea() for locking the fseal bit to 1
Add the following defines:
All status register bits
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
SY8106A is a PMIC which is used on the Allwinner
H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is
implemented to set the default V-CPU voltage to 1200 mV.
This driver is required to ensure the SY8106A V-CPU
voltage is set to 1200 mV after a software reset. On cold
boot the default SY8106A output voltage is selected to be
1200 mV by a pair of resistors on the Orange Pi PC and Plus.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Previously, AXP818 ALDO support was partially added to Kconfig, but
never enabled in the board file, nor properly set or configured in
Kconfig. The boards continue to work because the AXP818 is designed
to pair with the A83T/H8, and the default voltages match the reference
design's requirements.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
AXP818 provides an array of LDOs to provide power to various peripherals.
None of these regulators are critical.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Instead of one function for each DLDO regulator, make 1 function that
takes an extra "index". Since the control bits for the DLDO regulators
are contiguous, this makes the function very simple. This removes a lot
of duplicate code.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Adds poweroff support for axp209 pmic.
Signed-off-by: Michael van Slingerland <michael@deviousops.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Some regulators will not implement any operations (e.g. fixed regulators).
This is not an error, so allow the autoset process to continue when one
of these regulators is found.
Signed-off-by: Simon Glass <sjg@chromium.org>
The currect PMIC debugging is a little confusing. Adjust it so that it is
clear whether the operation succeeded or failed. Also, avoid creating a new
error return value when a perfectly good one is already available.
Signed-off-by: Simon Glass <sjg@chromium.org>
For some boards the pmic interface is useful but the regulator interface
(which comes with it) is too large. Allow them to be separated such that
SPL can decide which it needs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add regulator support for the RK808 PMIC. It integrated 4 BUCKs and 8 LDOs
all of which are supported by this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
This Rockchip PMIC provides features suitable for battery-powered
applications. It is commonly used with Rockchip SoCs.
Add a driver which provides register access. The regulator driver will use
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
With gcc-5.3 we get a warning for using switch() on a bool type.
Rewrite these sections as if/else and update the one section that was
using 1/0 instead of true/false.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
AXP818 is rsb based PMIC and used on Allwinner A83T H8 Homlet dev board.
It's registers are different and calculating reg config is different than
that of earlier axp power ICs.
DCDC1, DCDC2, DCDC3 and DCDC5 is implemented at the moment.
all other voltages can be added subsequently.
AXP datasheet is uploaded to wiki:
http://linux-sunxi.org/File:AXP818_datasheet_Revision1.0.pdf
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add initial sun8i H3 support, only uart + mmc are supported for now.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some devices are supplied by configurable regulator's output.
But there was no function for getting it. This commit adds
function, that allows for getting the supply device by it's phandle.
The returned regulator device can be used with regulator uclass's API.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This driver allows I/O operations on the Samsung S2MPS11 PMIC,
which provides lots of LDO/BUCK outputs.
To enable it, update defconfig with:
- CONFIG_PMIC_S2MPS11
and additional, if were not defined:
- CONFIG_CMD_PMIC
- CONFIG_ERRNO_STR
The binding info: doc/device-tree-bindings/pmic/s2mps11.txt
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
LDO3 and LDO4 are normally either unused, or used to power csi
attached camera sensors, and as such do not need to be enabled at
boot time.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for disabling the regulators found on the axp209 pmic.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The only thing axp221.c's axp_init() does which needs protection
against multiple calls is calling pmic_bus_init, and pmic_bus_init()
itself is already protected against being called multiple times.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Use the generic pmic_bus helpers for the axp152 / axp209 drivers,
rather then having them define their own register read / write
functions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V, make this
the default.
Note that this does not cause any functional changes since all sun8i
board defconfig-s already contained: CONFIG_AXP_ALDO1_VOLT=3000 .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Change the axp223 dcdc2 / VDD-SYS default from 1.2V to 1.1V, 1.1V is the
value recommended by Allwinner and is what most fex files specify.
This has been tested on a number of A23/A33 tablets including on an
A23 Ippo-q8h-v1.2 PCB tablet which has a fex file which specifies 1.2V
(which is where our original 1.2V default comes from).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Stop prefixing the axp functions for setting voltages, etc. with the
model number, there ever is only one pmic driver built into u-boot,
this allows simplifying the callers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On boards with axp221/223 pmic-s we already allow configuring most
voltages. Make the Kconfig options for these also apply to boards with
axp152 / axp209 pmic-s and extend them to configure all voltages.
The Kconfig defaults are chosen so that this commit does not introduce any
functional changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Kconfig-ify CONFIG_AXP152_POWER and _AXP209_POWER settings, removing
them from CONFIG_SYS_EXTRA_OPTIONS.
Note that sun5i boards can have either an AXP209 or an AXP152 pmic, the
Kconfig default is AXP209, boards with an AXP152 must explicitly select
this. Likewise boards without a pmic must explicitly select SUNXI_NO_PMIC
in their defconfig.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a full regulator driver for the ACT8846. This provides easy access to
voltage and current settings for each regulator.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a driver for the ACT8846 PMIC. This supports several LDOs and BUCKs and
is connected to the I2C bus. This driver supports using a regulator driver
to access the regulators.
Signed-off-by: Simon Glass <sjg@chromium.org>
* Add pmic pfuze3000 support, implement power_pfuze3000_init to be
used in power_init_board callback function.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Allow specifying the axp221 dcdc2 voltage via Kconfig, this is necessary
because on some boards the 1.2V default does not work reliable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This part of mentioned commit, was missed by my mistake during the rebase.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Original commit message:
power: pmic: pfuze100 support driver model
1. Support driver model for pfuze100.
2. Introduce a new Kconfig entry DM_PMIC_PFUZE100 for pfuze100
3. This driver intends to support PF100, PF200 and PF3000, so add
the device id into the udevice_id array.
4. Rename PMIC_NUM_OF_REGS macro to PFUZE100_NUM_OF_REGS.
Change-Id: I4fc88414f3c0285f9648e47ec7aed60addeccc4d
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a simple pmic driver for the hi6553 pmic which is used in
conjunction with the hi6220 SoC on the hikey board. Eventually this
driver will be updated to be a proper UCLASS PMIC driver which
can parse the voltages direct from device tree.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
This adds support for powering off (the omap3 SoC) from the twl4030. This is
especially useful when the kernel does not actually power off the device using
this method but reboots and leaves it up to the bootloader to actually turn the
power off.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The return type of pmic_read and pmic_write is signed int, so
correct variable 'ret' from type unsigned int to int.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
1. Add new regulator driver pfuze100.
* Introduce struct pfuze100_regulator_desc for maintaining info
for one regulator.
2. Add new Kconfig entry DM_REGULATOR_PFUZE100 for pfuze100.
3. This driver intends to support PF100, PF200 and PF3000.
4. Add related macro definition in pfuze header file.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
1. Support driver model for pfuze100.
2. Introduce a new Kconfig entry DM_PMIC_PFUZE100 for pfuze100
3. This driver intends to support PF100, PF200 and PF3000, so add
the device id into the udevice_id array.
4. Rename PMIC_NUM_OF_REGS macro to PFUZE100_NUM_OF_REGS.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
If there is no property named 'regulator-name' for regulators,
choose node name instead, but not directly return failure value.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Remove the old drivers (both the normal one and the cros_ec one) now that
we have new drivers that use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Not all regulators can be set up automatically. Adjust the code so that
regulators_enable_boot_on() will return success when some are skipped.
Only genuine errors are reported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Some regulators use the wrong voltage register and thus it is not possible
to control them. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
This should write the register, not read it. Fix this bug.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
