Enable AHB support for Flexspi controller interface meaning
memory can be accessed via md command using absolute addresses
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hardware comes out of reset with implicit values, but these are outside
the accepted range for Layerscape gen 3 chassis spec used on LS1028A.
Allocate different IDs and fix up Linux DT to use them.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
USB3.0 Receiver needs to enable fixed equalization
for each of PHY instances in an SOC. This is similar
to erratum A-009007, but this one is for LX2160A,
and the register value is different.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Although layerscape platforms reuse mxc_get_clock() of i.MX platforms,
eSDHC clock getting do not have to use it. It uses global data
gd->arch.sdhc_clk directly in fsl_esdhc driver. Even there are more
than one eSDHC controllers on SoC, they use same reference clock.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Erratum A-050382 states that the eDMA ICID programmed in the eDMA_AMQR
register in DCFG is not correctly forwarded to the SMMU.
The workaround consists in programming the eDMA ICID in the eDMA_AMQR
register in DCFG to 40.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
If SEC FW support is not enabled (ARMV8_SEC_FIRMWARE_SUPPORT=n), below
compilation error appears
arch/arm/include/asm/arch-fsl-layerscape/fsl_icid.h:169:4: error:
'CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT' undeclared here (not in a function)
Fix it by wrapping with CONFIG_IS_ENABLED().
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2160A/LX2120A/LX2080A SVR value should be
0x873600/0x873620/0x873602
Previous values were valid only if CAN fuse is blown.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
ls1028a has 4 personalities: ls1028a, ls1027a, ls1017a and ls1018a.
Both ls1027a and ls1017a personalities are lower functionality version
which doesn't support the multimedia subsystems, like LCD, GPU.
To disable multimedia feature on non-multimedia version,
set the status property to disabled in dts nodes.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Program register bit of SCFG_SNPCNFGCR_USBxRDSNP and
SCFG_SNPCNFGCR_USBxWRSNP(x = 1, 2, 3) to drive USBx read/write
snoop signal on LS1043A and LS1046A.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add LS1027A, LS1018A and LS1017A personalities support to
LS1028A SoC family.
LS1028A is the prime personality of LS1028A SoC family.
LS1027A is a lower funtionality version of QorIQ LS1028A
which does not support the multimedia subsystems, such as LCD
controller, GPU, and eDP PHY.
The QorIQ LS1018A and LS1017A SoCs are single 64-bit Arm A72
core, low power versions of the QorIQ LS1028A and LS1027A
SoCs respectively.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, sec. The ICID macros for SEC needed to be adapted because
the format of the registers is different.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The current implementation assumes that the registers holding the ICIDs
are universally big endian. That's no longer the case on newer
platforms so update the code to take into account the endianness of
each register.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
I2C dm mode enablemenet causes below compilation errors:
In file included from include/config.h:8:0,
from include/common.h:20:
include/config_fallbacks.h:51:4: error: #error "Cannot define
CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
# error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
^~~~~
In file included from include/config.h:8:0,
from include/common.h:20:
include/config_fallbacks.h:51:4: error: #error "Cannot define
CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
# error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
^~~~~
board/freescale/lx2160a/lx2160a.c: In function 'board_early_init_f':
board/freescale/lx2160a/lx2160a.c:108:2: warning: implicit declaration
of function 'i2c_early_init_f'; did you mean 'arch_early_init_r'?
[-Wimplicit-function-declaration]
i2c_early_init_f();
^~~~~~~~~~~~~~~~
arch_early_init_r
drivers/i2c/mxc_i2c.c: In function 'mxc_i2c_probe':
drivers/i2c/mxc_i2c.c:824:8: warning: implicit declaration of function
'enable_i2c_clk';
did you mean 'enable_irq_wake'? [-Wimplicit-function-declaration]
ret = enable_i2c_clk(1, bus->seq);
^~~~~~~~~~~~~~
enable_irq_wake
So fix these compilation errors.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
LS1028A includes an integrated PCI bus with 11 PCI functions residing on
bus 0. ECAM plus the device register space takes up 256MB of address
space.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Layerscape began to use two eSDHC controllers, for example,
LS1028A. They are same IP block with same reference clock.
This patch is to add clock support for the second eSDHC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Enable workaround for USB erratum A-008997. Here PCSTXSWINGFULL
registers has been moved to DSCR as compared to other Layerscape SoCs
where it was in SCFG.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The lx2160a have up to 6 PCIe controllers and have different
address and size of PCIe region.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The LS2080A has 8GB region for each PCIe controller, while the
other platforms have 32GB.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
sec_firmware reserves JR3 for it's own usage and deletes the JR3 node
from the device tree. This causes this warning to be issued when doing
the device tree fixup:
WARNING could not find node fsl,sec-v4.0-job-ring: FDT_ERR_NOTFOUND.
Fix it by excluding the device tree fixup for the JR reserved by
sec_firmware.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The SEC QI ICID setup in the QIIC_LS register is actually an offset
that is being added to the ICID coming from the qman portal. Setting
it with a non-zero value breaks SMMU setup as the resulting ICID is
not known. On top of that, the SEC QI ICID must match the qman portal
ICIDs in order to share the isolation context.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Moves FSL_TZASC_400 and FSL_TZPC_BP147 configs to Kconfig
for LS1088A and LS2088A platforms.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As per hardware documentation,
CONFIG_SYS_FSL_PEBUF_BASE for lx2160a is 0x1c00000000
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The ICIDs for the qdma device are not configured through SCFG but
through some registers found in the actual device register block.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1043A/LS1023A 23x23 package silicon has different SVR:VAR_PER.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
NXP layerscape architecture Chassis 3.2 builds upon chassis3
architecture with changes like DDR Memory map change,
removal of IFC and support of upto 8 I2C controller.
Patch add README.lsch3_2 and the above changes under
macro CONFIG_NXP_LSCH3_2.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some lsch3 based SoCs like lx2160a contains three
serdes modules.
Add support for third serdes protocol in lsch3
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Workaround of erratum A010539 clears the RCW source field in PORSR1
register, causing failure of detecting boot source using this method.
Use SMC call if U-Boot runs at EL2. If SMC is not implemented or
running at EL3, continue to read PORSR1 and presume QSPI as boot
source if erratum workaround A010539 is enabled and RCW source is
cleared.
Signed-off-by: York Sun <york.sun@nxp.com>
Adds SMC calls for getting DDR size and bank info for TFABOOT.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PORSR register holds the cfg_rcw_src field which can be used
to identify boot source.
Further, it can be used to select the environment location.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: fix multiple checkpatch issues]
Reviewed-by: York Sun <york.sun@nxp.com>
Move static definitions to cpu.c file, as it doesn't allow
the cpu.h file to be included in multiple c files.
Signed-off-by: York Sun <york.sun@nxp.com>
Reuse the existing ICID setup code done for LS1046A smmu enablement
and add the equivalent setup for LS1043A chips.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The QMan IP block in this SoC is version 3.2 so advertise
this in the SoC configuration header.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The iommu-map property in the fsl-mc node is updated by
valid stream-ids by u-boot. This patch is to fixup this
property for LS208x and LS1088.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Program Central Security Unit (CSU) to grant access to USB 2.0
controller.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: rewrite commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Move ns_dev[] from header file to C file to avoid compiling warning
when header file is included by others.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: rewrite commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for SEC ICID configuration and apply it for ls1046a.
Also add code to make the necessary device tree fixups.
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for ICID setting of fman ports and the required device
tree fixups.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
