Because the mvpp2 driver now relies on the PHYLIB and
the external MDIO driver, configuring low level
SMI bus settings is redundant.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
1. Differ between Port1 RGMII and SFI modes in Netcomplex config.
2. Remove XPCS config from SFI mode.
Port1 doesn't XPCS domain, XPCS config should be removed.
Access to Port1 XPCS can cause stall.
3. Add Port1 MPCS configurations.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
When the PHY interface is set as TXID & RXID, the delays should be taken from DT,
but first they should not be hardcoded since the PHY driver will set them.
Fixes: 798424e857 ("net: designware: add Amlogic Meson8b & later glue driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Currently driver may end up caching disabled port ID as active
interface. Fix this by bailing out earlier in case port is marked
disabled in the DT.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CPSW NUSS IP on K3 SoCs can have more than one external port (upto 8)
Therefore increase AM65_CPSW_CPSWNU_MAX_PORTS to 9 (8 ext + 1 Root port)
as preparation to allow any one of the 8 ports to be used as ethernet
interface in U-Boot.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
If we fail to probe for whatever reason, we cannot unregister/free the
MII bus unless we registered it with fec_get_miibus. This fixes FECs
sharing an MDIO bus from destroying it, preventing the other FEC from
using it.
Fixes: 6a895d039b ("net: Update eQos driver and FEC driver to use eth phy interfaces")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If a phy is disabled, don't use it. This matches Linux's behavior.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
binman FMAP improvements
minor test improvements and fixes
minor dm improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmCKoLERHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYCpgf/ROfOg76k18PdWcQTZr10CnU0iqTaOyYx
129hvb4n4bx4Q7Zr/HrWT6y7vvD01NOiNCwSX8qdF7S1bqs2/2AM+Yk/vLimXVOg
UDGXGRABkbHQFVMzBUSmlmQvKoG5G6AhS6/5/F7q4jj+QCVMGarves7G7ImhFOFw
6WKeNGv6FWX4UPSxm0TDJETiIqURNZOsu2vU9DmkR/b1eY13/qf/9J4zzEP1DaJt
7PrKmyblRhPlMsi59EjNyEQOnY/A17en8Ik3Zt336tLPELlczRc4Xp8HslQsy2i3
o457il6x8kl828oVwm3Sx4R/UvM8+qE1jWRcPA7vWrxCy3+AqDcTfQ==
=tiPD
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-29apr21' of https://source.denx.de/u-boot/custodians/u-boot-dm
buildman environment fix
binman FMAP improvements
minor test improvements and fixes
minor dm improvements
Today of_address_to_resource() is called only in
ofnode_read_resource() for livetree support and
fdt_get_resource() is called when livetree is not supported.
The fdt_get_resource() doesn't do the address translation
so when it is required, but the address translation is done
by ofnode_read_resource() caller, for example in
drivers/firmware/scmi/smt.c::scmi_dt_get_smt_buffer() {
...
ret = ofnode_read_resource(args.node, 0, &resource);
if (ret)
return ret;
faddr = cpu_to_fdt32(resource.start);
paddr = ofnode_translate_address(args.node, &faddr);
...
The both behavior should be aligned and the address translation
must be called in fdt_get_resource() and removed for each caller.
Fixes: a44810123f ("dm: core: Add dev_read_resource() to read device resources")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
The commit 6c993815bb ("net: phy: xilinx: Be compatible with live OF
tree") change driver behavior to while loop which wasn't correct because
the driver was looping over again and again. The reason was that
ofnode_valid() is taking 0 as correct value.
Fix it by changing while loop to ofnode_for_each_subnode() which is only
loop over available nodes.
Fixes: 6c993815bb ("net: phy: xilinx: Be compatible with live OF tree")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The dw_eth_pdata is not accessible from the mdio device, it gets the mdio bus plat
leading to random sleeps (-10174464 on Odroid-HC4).
This moves the dw_mdio_reset function to a common one taking the ethernet
device as parameter and use it from the dw_mdio_reset and dm_mdio variant functions.
Fixes: 5160b4567c ("net: designware: add DM_MDIO support")
Reported-by: Mark Kettenis <mark.kettenis@xs4all.nl>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Commit eb5a2b6710 ("net: sun8i-emac: Determine pinmux based on SoC,
not EMAC type") switched the pinmux setup over to look at
CONFIG_MACH_SUN* symbols, to find the appropriate mux value.
Unfortunately this patch missed to check for the H5, which is
pin-compatible to the H3, but uses a different Kconfig symbol (because
it has ARMv8 vs. ARMv7 cores).
Replace the pure SUN8I_H3 symbol with the joint SUNXI_H3_H5 one, which is
there to cover the peripherals common to both SoCs.
Also explicitly list each supported SoC, and have an error message in the
fallback case, to avoid those problems in the future.
This fixes Ethernet support on all H5 boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi PC2
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Sometimes no traffic was getting out on the ports, the root cause was
a wrong configuration of the Serdes6G, which is used on jr2 pcb111.
This patch fixes this issue by applying the correct configuration.
Fixes: 5e1d417bec ("net: Add MSCC Jaguar2 network driver.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Make sure to reset the switch core at probe time.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
To squash that nasty warning message and make better use of the newly
gained OF_CONTROL feature, let's convert the calxedagmac driver to the
"new" driver model.
The conversion is pretty straight forward, mostly just adjusting the
use of the involved data structures.
The only actual change is the required split of the receive routine into
a receive and free_pkt part.
Also this allows us to get rid of the hardcoded platform information and
explicit init calls.
This also uses the opportunity to wrap the code decoding the MMIO
register base address, to make it safe for using PHYS_64BIT later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The fdt node offset is apparently not set properly when probed
causing no MDIO busses to be found. Fix this by obtaining the
offset.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Revert a change that occured between the Marvell SDK-10.1.1.0
and SDK-10.3.1.1 which broke QSMII phy support.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
At present the tsec driver uses a non-standard DT bindings to get
its <reg> base / size. The upstream Linux kernel seems to require
the <reg> base / size to be put under a subnode of the eTSEC node
with a name prefix "queue-group". This is not documented in the
kernel DT bindings, but it looks every dtsi file that contains the
eTSEC node was written like this.
This commit updates the tsec driver to handle this case.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
dev_remap_addr() eventually calls dev_read_addr_index(), while
pdata->iobase holds the return value of dev_read_addr() that calls
dev_read_addr_index() too. Such duplication can be avoided by using
map_physmem() directly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The DSA sandbox driver is used for unit testing the DSA class code.
It implements a simple 2 port switch plus 1 CPU port, and uses a
very simple tag to identify the ports.
The DSA sandbox device is connected via CPU port to a regular Ethernet
sandbox device, called 'dsa-test-eth, managed by the existing eth
sandbox driver. The 'dsa-test-eth' is not intended for testing the
eth class code however, but it is used to emulate traffic through the
'lan0' and 'lan1' front pannel switch ports. To achieve this the dsa
sandbox driver registers a tx handler for the 'dsa-test-eth' device.
The switch ports, labeled as 'lan0' and 'lan1', are also registered
as eth devices by the dsa class code this time. So pinging through
these switch ports is as easy as:
=> setenv ethact lan0
=> ping 1.2.3.5
Unit tests for the dsa class code were also added. The 'dsa_probe'
test exercises most API functions from dsa.h. The 'dsa' unit test
simply exercises ARP/ICMP traffic through the two switch ports,
including tag injection and extraction, with the help of the dsa
sandbox driver.
I took care to minimize the impact on the existing eth unit tests,
though some adjustments needed to be made with the addition of
extra eth interfaces used by the dsa unit tests. The additional eth
interfaces also require MAC addresses, these have been added to the
sandbox default environment.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <20210216224804.3355044-5-olteanv@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that the fixed phy driver has been fully adapted to OF APIs,
and dm_eth_phy_connect() already can handle the fixed phy, call
dm_eth_phy_connect() directly in the DM tsec driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210216224804.3355044-4-olteanv@gmail.com>
[bmeng: split from "net: mdio: teach dm_eth_phy_connect to connect to fixed PHY"]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Update fixedphy_probe() to support the old DT binding.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The printf statement doesn't end with a newline. Add it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The PHY driver ops should be made static.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Simplify the logic of phy_connect_fixed() by using the new API
ofnode_phy_is_fixed_link(), which brings additional bonus of
supporting the old DT bindings.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present phy_connect_gmii2rgmii() is implemented using a DM API
dev_of_offset() hence it cannot support a non-DM configuration.
Remove the non-DM version prototype of phy_connect_gmii2rgmii()
and make the driver depend on CONFIG_DM_ETH.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Following the same updates that were done to the fixed phy driver,
use ofnode_ APIs instead of fdt_ APIs so that the Xilinx PHY driver
can support live DT.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In drivers/net/phy/Kconfig, CONFIG_PHY_FIXED already depends on
CONFIG_DM_ETH, so the function prototype definition when
CONFIG_DM_ETH=n does nothing, so it can be dropped. It is also
never reachable, since the whole function is already under #ifdef
CONFIG_PHY_FIXED (which again, as I said, depends on CONFIG_DM_ETH=y).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210216224804.3355044-3-olteanv@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
On systems that use CONFIG_OF_LIVE, the "ofnode" type is defined
as const struct device_node *np, while on the flat DT systems it
is defined as a long of_offset into gd->fdt_blob.
It is desirable that the fixed PHY driver uses the higher-level
ofnode abstraction instead of parsing gd->fdt_blob directly,
because that enables it to work on live OF systems.
The fixed PHY driver has used a nasty hack since its introduction in
commit db40c1aa1c ("drivers/net/phy: add fixed-phy /
fixed-link support"),
which is to pass the long gd->fdt_blob offset inside int phydev->addr
(a value that normally holds the MDIO bus address at which the PHY
responds). Even ignoring the fact that the types were already
mismatched leading to a potential truncation (flat OF offset was
supposed to be a long and not an int), we really cannot extend this
hack any longer, because there's no way an int will hold the other
representation of ofnode, the struct device_node *np.
So we unfortunately need to do the right thing, which is to use the
framework introduced by Grygorii Strashko in
commit eef0b8a930 ("net: phy: add ofnode node to struct phy_device").
This will populate phydev->node for the fixed PHY.
Note that phydev->node will not be valid in the probe function, since
that is called synchronously from phy_device_create and we really have
no way of passing the ofnode directly through the phy_device_create API.
So we do what other drivers do too: we move the OF parsing logic from
the .probe to the .config method of the PHY driver. The new function
will be called at phy_config() time.
I do believe I've converted all the possible call paths for creating
a PHY with PHY_FIXED_ID, so there is really no reason to maintain
compatibility with the old logic of retrieving a flat OF tree offset
from phydev->addr. We just pass 0 to phydev->addr now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210216224804.3355044-2-olteanv@gmail.com>
[bmeng: keep fixedphy_probe(); update mdio-uclass.c to handle fixed phy]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them. As the P5020 is the last ARCH_P5020 platform, remove that
support as well.
Cc: Andy Fleming <afleming@gmail.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. It is also the only ARCH_T2081 board so remove that support
as well.
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds a proper glue driver for the Designware DWMAC ethernet MAC IP
found in the Amlogic Meson8, GXBB, GXL, GXM, G12A, G12B & SM1 SoCs.
This is aimed to replace the static ethernet link setup found on the board
init code for the Amlogic SoC based boards.
Tested on a libretech-cc (S905x Internal RMII 10/100 PHY) and Khadas VIM3 (A113d
with external 10/100/1000 RGMII PHY) to cover the most extreme setups.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic G12A & compatible SoCs embeds a mux to either communicate with
the external PHY or the internal 10/100 PHY.
This adds support for this mux as a MDIO MUX device.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support for DM_MDIO to connect to PHY and expose a MDIO device for the
internal MDIO bus in order to dynamically connect to MDIO PHYs with DT
with eventual MDIO muxes in between.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support for MMIO register MDIO muxes based on the Linux mdio-mux-mmioreg driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The code was trying to disable PCS auto-negotiation when a fixed-link node
is present and enable it otherwise. However, the PCS registers were being
written before the PCSSEL bit was set in the network configuration
register, and it appears that in this state, PCS register writes are
ignored. The result is that the intended change only took effect on the
second network operation that was performed, since at that time PCSSEL is
already enabled.
Fix the order of register writes so that PCS registers are only written to
after the PCS is enabled.
Fixes: 26e62cc971 ("net: gem: Disable PCS autonegotiation in case of fixed-link")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When copying to a u32 field we should use sizeof(u32) and not
sizeof(*u32) in memcpy.
On 64bit systems like cortina_presidio-asic-emmc_defconfig using
sizeof(*u32) leads to a buffer overrun.
Fixes: febe13b438 ("net: cortina_ni: Add eth support for Cortina Access CAxxxx SoCs")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
qspi:
- Support for dual/quad mode
- Fix speed handling
clk:
- Add clock enable function for zynq/zynqmp/versal
gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path
fpga:
- Fix buffer alignment for ZynqMP
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYDUezQAKCRDKSWXLKUoM
IbtgAJ9jZ+BOtwFaHR19TENC2DsHTINnnwCfSDn3fU0OFJRI0HD7pRxXr4xrb3M=
=Kr8x
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.04-rc3
qspi:
- Support for dual/quad mode
- Fix speed handling
clk:
- Add clock enable function for zynq/zynqmp/versal
gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path
fpga:
- Fix buffer alignment for ZynqMP
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
Enable rx clock along with tx clock for versal platform. Use compatible
data to enable/disable clocks in the driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
A lot of Xilinx drivers are checking -ENOSYS which means that clock driver
doesn't have enable function. Remove this checking from drivers and create
dummy enable function as was done for clk_fixed_rate driver by
commit 6bf6d81c11 ("clk: fixed_rate: add dummy enable() function").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This driver is used for the Ethernet switch integrated into LS1028A NXP.
Felix on LS1028A has 4 front panel ports and two internal ports, I/O
to/from the switch is done through an ENETC Ethernet interface.
The 4 front panel ports are available as Ethernet interfaces and can be
used with the typical network commands like tftp.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
DSA stands for Distributed Switch Architecture and it covers switches that
are connected to the CPU through an Ethernet link and generally use frame
tags to pass information about the source/destination ports to/from CPU.
Front panel ports are presented as regular ethernet devices in U-Boot and
they are expected to support the typical networking commands.
DSA switches may be cascaded, DSA class code does not currently support
this.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
The DSA (Distributed Switch Architecture) implementation has made a
design decision when it got introduced to the Linux kernel in 2008.
That was to hide away from the user the CPU-facing Ethernet MAC, since
it does not make sense to register it as a struct net_device (UCLASS_ETH
udevice for U-Boot), because that would never be beneficial for a user:
they would not be able to use it for traffic, since conceptually, a
packet delivered to the CPU port should loop back into the system.
Nonetheless, DSA has had numerous growing pains due to the lack of a
struct net_device for the CPU port, but so far it has overcome them.
It is unlikely at this stage of maturity that this aspect of it will
change.
We would like U-Boot to present the same information as Linux, to be at
parity in terms of number of interfaces, so that ethNaddr environment
variables could directly be associated between U-Boot and Linux.
Therefore, we would implicitly like U-Boot to hide the CPU port from the
user as well.
But the paradox is that DSA still needs a struct phy_device to inform
the driver of the parameters of the link that it should configure the
CPU port to. The problem is that the phy_device is typically returned
via a call to phy_connect, which needs an udevice to attach the PHY to,
and to search its ofnode for the 'fixed-link' property. But we don't
have an udevice to present for the CPU port.
Since 99% of DSA setups are MAC-to-MAC connections between the switch
and the host Ethernet controller, the struct phy_device is going to be a
fixed PHY. This simplifies things quite a bit. In U-Boot, a fixed PHY
does not need an MDIO bus, and does not need an attached dev either.
Basically, the phy_connect call doesn't do any connection, it just
creates the fixed PHY.
The proposal of this patch is to introduce a new fixed_phy_create
function which will take a single argument: the ofnode that holds this:
port@4 {
reg = <4>;
phy-mode = "internal";
fixed-link {
speed = <2500>;
full-duplex;
};
};
and probe a fixed PHY driver using the information from this ofnode.
DSA will probably be the only user of this function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Unlike the Linux fixed PHY driver, the one in U-Boot does not attempt to
emulate the clause 22 register set of a gigabit copper PHY driver
through the swphy framework. Therefore, the limitation of being unable
to support speeds higher than gigabit in fixed-link does not apply to
the U-Boot fixed PHY driver. This makes the fixed-link U-Boot
implementation more similar to the one from phylink, which can work with
any valid link speed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
At present this function does not accept a size for the FIT. This means
that it must be read from the FIT itself, introducing potential security
risk. Update the function to include a size parameter, which can be
invalid, in which case fit_check_format() calculates it.
For now no callers pass the size, but this can be updated later.
Also adjust the return value to an error code so that all the different
types of problems can be distinguished by the user.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Bruce Monroe <bruce.monroe@intel.com>
Reported-by: Arie Haenel <arie.haenel@intel.com>
Reported-by: Julien Lenoir <julien.lenoir@intel.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
As this is the last SH4A board, remove that support as well.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Patch-cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Patch-cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
If probe fails, the mdio bus isn't unregistered. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current MDIO wait time is too long, which introduce long delay when
PHY negotiation register checking. Reduce it to 10us
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
We have encountered circumstances when a board design does not include
pull-up resistors on the external MDIO buses which are not used. This
leads to the MDIO data line not being pulled-up, thus the MDIO controller
will always see the line as busy.
Without a timeout in the MDIO bus driver, the execution is stuck in an
infinite loop when any access is initiated on that external bus.
Add a timeout in the driver so that we are protected in this
circumstance. This is similar to what is being done in the Linux
xgmac_mdio driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
priv->iobase was declared as phys_addr_t which is now a 64-bit
address. In a 32-bit build, this causes the following warning
seen when building ftmac100.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Cast priv->iobase with uintptr_t.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The pinmux choice for the RMII/RGMII pins the EMAC is connected to is
not dependent on the EMAC IP, but on the SoC it is integrated in.
Deriving the pinmux from the DT compatible string (as we do at the
moment) will thus cause problems with certain EMAC IP / SoC combinations.
To avoid this exact issue with the H616, let's use our Kconfig MACH
symbols to choose the correct pinmux setup.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
At the moment we only consider the EPHY register for those SoCs were
we actually have an internal PHY to configure. However even other SoCs
have this register, an expect the EPHY select bit to be cleared for
proper operation with an external PHY.
Rework sun8i_emac_set_syscon_ephy() to be called regardless of the EMAC
model, and clear the H3_EPHY_SELECT bit if no internal PHY is used.
We get away without it so far because SoCs like the A64 clear this bit
on reset, but we need to explicitly clear it on the H616, for instance.
The Linux driver does so as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
The phydev structure has a PHY OF node pointer in it, use that OF node
first when looking up PHY OF node properties, since that is likely the
correct PHY OF node pointer. If the pointer is not valid, which is the
case e.g. on legacy DTs, fall back to parsing MAC ethernet-phy subnode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Add phy driver support for MACs embedded inside Cortina Access SoCs
Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Tom Rini <trini@konsulko.com>
CC: Aaron Tseng <aaron.tseng@cortina-access.com>
Moved out PHY specific code out of Cortina NI Ethernet driver
and into a Cortina Access PHY interface driver
Add some missing address translations from virtual address in local DRAM
to physical address, which is needed for the DMA transactions to work
correctly.
This issue was detected while testing the e1000 driver on the MIPS
Octeon III platform, which needs address translation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Using (dm_)pci_virt_to_mem() is incorrect to translate the virtual
address in local DRAM to a physical address. The correct macro here
is virt_to_phys() so switch to using this macro.
As virt_to_bus() is now not used any more, this patch also removes
both definitions (DM and non-DM).
This issue was detected while testing the e1000 driver on the MIPS
Octeon III platform, which needs address translation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
bus_to_phys() is defined but not referenced at all. This patch removes
it completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
So far all GBit users of the sun8i-emac driver were using the "rgmii"
PHY mode, even though this turns out to be wrong. It just worked because
the PHY driver doesn't do the proper setup (yet).
In fact for most boards the "rgmii-id" or "rgmii-txid" PHY modes are the
correct ones.
To allow the DTs to describe the phy-mode correctly, and to stay
compatible with Linux, at least allow those other RGMII modes in the
driver.
This avoids breakage if mainline DTs will be synced with U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
This patch adds ethernet driver for MediaTek MT7620 SoC.
The MT7620 SoC has a built-in ethernet (Frame Engine) and a built-in
7-port switch and two xMII interfaces (can be MII/RMII/RGMII).
The port 0-3 of the switch connects to intergrited FE PHYs. Port 4 can be
configured to connect to either the intergrited FE PHY, or the xMII.
Port 5 always connects to the xMII. Port 6 is the CPU port.
This driver supports MT7530 giga switch connects to port 5.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Take into account all RGMII interface types. Depending on it
the RGMII PHY's timings are setup.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
clk_set_rate() returns the set rate in case of success and a
negative number in case of failure. Consider failure only the
negative numbers.
Fixes: 3ef64444de ("dm: net: macb: Implement link speed change callback")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Different implementation of USER IO register needs different
mapping for bit fields of this register. Add implementation
for this and, since clken is part of USER IO and it needs to
be activated based on per SoC capabilities, add caps in
macb_config where clken specific information needs to be filled.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
The DWMAC4 IP has the possibility to skip up to 7 AXI bus width size words
after the descriptor. Use this to pad the descriptors to cacheline size and
remove the need for noncached memory altogether. Moreover, this lets Tegra
use the generic cache flush / invalidate operations.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
A sporadic condition occurs when the "bad packet" error is triggered
repeatedly, which results in "bad packet" messages scrolling on the
console during transfer. To avoid triggering this, reset the internal
RXFC count on the first occurance of the "bad packet", which forces
the code to re-read the RX packet count from the MAC, and prevents
any additional "bad packet" messages if there are no more packets in
the MAC. Also print better debug information if this condition occurs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Tom Rini <trini@konsulko.com>
Implement programming MAC address to the hardware also for device model
configuration.
Fixes: b565b18a29 ("board: ge: bx50v3: Enable DM for PCI and ethernet")
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Read phy address from device tree and use it to find the phy device
if not found then search in the range of 0 to 31.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Enable 32-bit or 64-bit DMA in the macb driver based on the macb
hardware compatibility and it is configured with structure macb_config
in the driver.
The Microchip PolarFire SoC Memory Protection Unit(MPU) gives the 64-bit
DMA access with the GEM, the MPU transactions on the AXI bus is 64-bit
not 32-bit So 64-bit DMA is enabled for the Microchip PolarFire SoC GEM.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Add a return value to bb_miiphy_init and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In non-secure mode (EL2), MAC driver calls the SMC/PSCI services
provided by ATF to setup the PHY interface.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Checking for seq == -1 is effectively checking that the device is
activated. The new sequence numbers are never -1 for a bound device, so
update the check.
Also drop the note about valid sequence numbers so it is accurate with the
new approach.
Signed-off-by: Simon Glass <sjg@chromium.org>
Several Octeon drivers operate by setting the sequence number of their
device. This should not be needed with the new sequence number setup. Also
it is not permitted. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is not necessary anymore, since device_bind_ofnode() does
the same thing and works with both flattree and livetree.
Rename it to indicate that it is special.
Signed-off-by: Simon Glass <sjg@chromium.org>
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[Fixed whitespace errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can
be controlled via defconfig files.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case there is an EEPROM attached to the KS8851 MAC and the EEPROM
contains a valid MAC address, the MAC address is loaded into the NIC
registers on power on. Read the MAC address out of the NIC registers
and provide it to U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
As per hardware documentation, ECx_PMUX has precedence
over SerDes protocol.
For LX2160/LX2162 if DPMACs 17 and 18 are enabled as SGMII
through SerDes protocol but ECx_PMUX configured them as RGMII,
then the ports will be configured as RGMII and not SGMII.
Signed-off-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This adds the driver for the IPQ40xx built-in MDIO.
This will be needed to support future PHY driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
When sending a command via the MDIO bus, the Designware MAC expects some
bits in the CMD register to describe the clock divider value between
the main clock and the MDIO clock.
So far we were omitting these bits, resulting in setting "00", which
means "/ 16", so ending up with an MDIO frequency of either 18.75 or
12.5 MHz.
All the internal PHYs in the H3/H5/H6 SoCs as well as the Gbit Realtek
PHYs seem to be fine with that - although it looks like to be severly
overclocked (the MDIO spec limits the frequency to 2.5 MHz).
However the external 100Mbit PHY on the Pine64 (non-plus) board is
not happy with that, Ethernet was actually never working there, as the
PHY didn't probe.
As we set the EMAC clock (via AHB2) to 300 MHz in ATF (on the 64-bit
SoCs), and use 200 MHz on the H3, we need the highest divider of 128
to let the MDIO clock end up below the required 2.5 MHz.
This enables Ethernet on the Pine64(non-plus).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The current implementation of sun8i_get_ephy_nodes() makes quite some
assumptions, in general relying on DT path names is a bad idea.
I think the idea of the code was to determine if we are using the
internal PHY, for which there are simpler and more robust methods:
Rewrite (and rename) the existing function to simply lookup the DT node
that "phy-handle" points to, using the device's DT node.
Then check whether the parent of that PHY node is using an "H3 internal
MDIO" compatible string. If we ever get another internal MDIO bus
implementation, we will probably need code adjustments anyway, so this
is good enough for now.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[jagan: rebase on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The error handling in recv() is somewhat broken, for instance
good_packet isn't really used, and it's hardly readable. Also we try
to check for short or too big packets, but those are actually filtered
out by the hardware.
Simplify the whole routine and improve the error handling:
- Bail out early if the current RX descriptor is not ready.
- Enable propagation of runt, huge and broken packets.
- Check for runt and huge packets, and return 0 to indicate this.
This will force the framework to call free_pkt for cleanup.
- Avoid aligning the packet buffer for invalidation again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The EMAC soft reset routine was subtly broken, using an open coded
timeout routine without any actual delay.
Remove the unneeded initial reset bit read, and call wait_for_bit_le32()
to handle the timeout correctly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When iterating over all RX/TX buffers, we were using a rather long "idx"
control variable, which lead to a nasty overlong line.
Replace "idx" with "i" to avoid this.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To meet the current alignment requirements for our cache maintenance
functions, we were explicitly aligning the *arguments* to those calls.
This is not only ugly to read, but also wrong, as we need to make sure
we are not accidentally stepping on other data.
Provide wrapper functions for the common case of cleaning or
invalidating a descriptor, to make the cache maintenance calls more
readable. This fixes a good deal of the problematic calls.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
There is no reason to invalidate a TX descriptor before we are setting
it up, as we will only write to a field.
Remove the not needed invalidate_dcache_range() call.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When we initialise the TX descriptors, there is no need yet to clean
them all to memory, as they don't contain any data yet. Later we will
touch and clean each descriptor anyway.
However we tell the MAC about the beginning of the chain, so we have to
clean at least the first descriptor, to make it clear that this is empty
and there are no packets to transfer yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Before we initialise the RX descriptors, there is no need to *clean*
them from the cache, as we touch them for the first time.
However we should cover the case that those buffers contain dirty cache
lines, which could be evicted and written back to DRAM any time later,
in the worst case *after* the MAC has transferred a packet into them.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The EMAC driver contains a lot of magic bits, although the manuals
and the Linux driver have all names for them.
Define those names and use them when programming the registers.
Also this replaces a lot of readl/mask/writel operations with the much
easier-to-read setbits_le32() macro.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Apparently due to copying from some older or converted driver, the
sun8i_emac driver contains pointless wrapper functions to bridge
between a legacy driver and the driver model.
Since sun8i_emac is (and always was) driver model only, there is no
reason to have those confusing wrappers. Just remove them, and use
the driver model prototypes directly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When preparing the register value for the MDIO command register, we
start with a zeroed register, so there is no need to mask off certain
bits before setting them.
Simplify the sequence, and rename the variable to a more matching
mii_cmd on the way.
Also the open-coded time-out routine can be replaced with a much safer
and easier-to-read call to wait_for_bit_le32().
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When initialising the TX DMA descriptors, we mostly chain them up,
but of course don't know about any data or its length yet.
That means they are still invalid, and the OWN bit should NOT be set
yet.
In fact when we later tell the MAC about the beginning of the chain,
and enable TX DMA in the start() routine, the MAC will start fetching
TX descriptors prematurely, as it can be seen by dumping the TX_DMA_STA
and TX_DMA_CUR_DESC registers.
Clear the owner bit, to not give the MAC the wrong illusion that it
owns the descriptors already.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When phy_startup() returns with an error, because there is no link or
the user interrupted the process, we shall stop the _start() routine
and return with an error, instead of proceeding anyway.
This fixes pointless operations when there is no Ethernet cable
connected, for instance.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- Octeon TX: Add NAND driver (Suneel)
- Octeon TX: Add NIC driver driver (Suneel)
- Octeon TX2: Add NIC driver driver (Suneel)
- Armada 8040: Add iEi Puzzle-M80 board support (Luka)
- Armada A37xx SPI: Add support for CS-GPIO (George)
- Espressobin: Use Linux model/compatible strings (Andre)
- Espressobin: Add armada-3720-espressobin-emmc.dts from Linux (Andre)
- Armada A37xx: Small cleanup of config header (Pali)
Set the defaults on probe for the packet buffer size registers
for the i210.
The TX/RX PBSIZE register of the i210 resets to its default value
only at power-on - see Intel Ethernet Controller I210 Datasheet rev 3.5
chapter 8.3 'Internal Packet Buffer Size Registers'.
If something (another driver, another OS, etc.) modifies this register
from its default value, the e1000 driver doesn't function correctly. It
detects a hang of the transmitter and continuously resets the adapter.
Here we set this value to its default when resetting the i210 to
resolve this issue.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Adds support for Network Interface controllers found on
OcteonTX2 SoC platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Adds support for Network Interface controllers found on
OcteonTX SoC platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The cell_count argument is required when cells_name is NULL.
This patch adds this parameter in live tree API
- of_count_phandle_with_args
- ofnode_count_phandle_with_args
- dev_count_phandle_with_args
This parameter solves issue when these API is used to count
the number of element of a cell without cell name. This parameter
allow to force the size cell.
For example:
count = dev_count_phandle_with_args(dev, "array", NULL, 3);
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Upon further discussion on the mailing list, we should not get in the
situation where the generic code path to set ethaddr/etc correctly does
not work. Revert this until someone can further debug the smc911x
driver regarding this issue.
This reverts commit 387cbf096e.
Signed-off-by: Tom Rini <trini@konsulko.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The ethernet controller can read the MAC from EEPROM and display it,
but if ethaddr is not set, the ethernet is still unavailable.
This patch checks will automatically set the MAC address if it has
not already been set.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
ftgmac100 driver is using hard-coded PHY interface address of zero.
Each board can have different PHY interface address (phy_addr).
This commit modifies the driver to make use of board specific address
by leveraging CONFIG_PHY_ADDR.
Signed-off-by: Thirupathaiah Annapureddy <thiruan@linux.microsoft.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The Linux kernel does set the clock delays to
- 0.2 ns (their default, and lowest, hardware value) if delays should
not be enabled
- 2.0 ns (which causes the data to be sampled at exactly half way between
clock transitions at 1000 Mbps) if delays should be enabled
depending on the interface mode
See https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/phy/mscc/mscc_main.c#n523
So instead of using arbitrary delay values like now, mimic this behaviour.
The behaviour is the same for all of vsc8530/8531/8540/8541 so move that
to a shared function while at it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The vsc8530/8531/8540/8541 phys have a configurable clock output that
can emit 25, 50 and 125 MHz rates, which in turn may be needed for
stable network connections.
This follows a similar change introduced into the Linux kernel at
https://lore.kernel.org/netdev/20200609133140.1421109-2-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Without DM_ETH, cpsw_priv.dev is an eth_device. Just use its name instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Pass a udevice into a few functions so `dev` is defined.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
There's no dev to log with, so pass the device along with the priv data.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
netdev_xxx evaluates to printf in U-Boot, so there is no extra info
printed. mvpp2 one of only two drivers which use these functions in U-Boot.
Convert these functions to dev_xxx where possible (and to log_xxx where
not).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove some prefixes, or get the device from the phy.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
netdev_xxx evaluates to printf in U-Boot, so there is no extra info
printed. mvneta is one of two drivers which use these functions in U-Boot.
Convert these functions to dev_xxx where possible (and to log_xxx where
not).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
No need for indirection here.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
The micrel phy driver is already configuring this values from
device tree. So remove the redundant phy configuration call from
this driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
CONFIG_DM_SPI_FLASH is only supported now with passing of driver
conversion deadline from non-DM to DM model. Hence, it's safe to remove
non-DM code check from pfe_spi_flash_init.
Also use CONFIG_ENV_SPI_MODE and CONFIG_ENV_SPI_MAX_HZ instead of
reading reading values from DT.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix Coverity issue: RESOURCE_LEAK.
leaked_storage: Variable addr going out of scope leaks the storage it
points to.
Fixes: e0152dbed6 ("net: pfe_eth: Use spi_flash_read API to access
flash memory")
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
All the 10G ports that were working in XFI mode were described as
using XGMII (as PHY_INTERFACE_MODE_XFI was not added at the time).
Add the minimal changes required for the FMan code to support XFI.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
PFE DDR addresses are now stored on to a stack varaiable rather
dynamic allocation.
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
correction in delay implementation before we exit out of tx timeout.
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The next DPMAC was always verified if it is enabled. In case of
DPMAC@6, the DPMAC@7 is verified. As DPMAC@7 is disabled, DPMAC@6 will
be considered disabled and not detected by uboot.
Signed-off-by: Grigore Popescu <grigore.popescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
The info of fixed-link PHY is described in DT node instead of
getting from MII, so detect the fixed-link PHY DT node first,
if it doesn't exist then probe the MII.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
For the platforms on which the eTSEC driver uses DM_ETH, convert its
MDIO controller code to also use DM_MDIO.
Note that for handling the TBI PHY (the MAC PCS for SGMII), we still
don't register a udevice for it, since we can drive it locally and there
is no point in doing otherwise.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Reworked to fix gazerbeam config]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The MII management register block offset is different between
gianfar and etsec2 compatible devices, this patch is to fix
this issue by adding driver data for different compatible
string.
Fixes: 2932c5a802 ("net: tsec: fsl_mdio: add DM MDIO support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Use virtual address to access the MII block registers instead
of physical address.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It is utterly pointless to require an MDIO bus pointer for a fixed PHY
device. The fixed.c implementation does not require it, only
phy_device_create. Fix that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
flush_cache() arguments are not type casted to take care of 64 bit
systems. Use phys_addr_t to type cast for it to work properly for 32 bit
and 64 bit systems.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
There are compilation warnings showing up when we compile AXI ethernet
driver for 64bit architectures. Fix them, so that it works on both 32
and 64 bit architectures.
DMA descriptors are not taking care of 64bit addresses. To fix it,
change axidma_bd members as below:
next ==> next_desc
reserverd1 ==> next_desc_msb
phys ==> buf_addr
reserverd2 ==> buf_addr_msb
and update next_desc and buf_addr with lower 32 bits of the addresses,
update next_desc_msb and buf_addr_msb with upper 32 bits of the 64bit
addresses.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Find out MDIO bus and enable MDIO access to it if this is done via
different GEM controller. Only works across GEM instances.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
add DM/DTS support for the UEC ethernet on QUICC Engine
Block.
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Patch-cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Patch-cc: Madalin Bucur <madalin.bucur@oss.nxp.com>
Series-changes: 3
- revert:
commit "3374264df97b" ("drivers: net: qe: deselect QE when DM_ETH is enabled")
as now qe works with DM and DM_ETH support.
- fix mailaddress from Holger
Series-changes: 2
- add comments from Qiang Zhao:
- add device node documentation
- I did not drop the dm_qe_uec_phy.c and use drivers/net/fsl_mdio.c
because using drivers/net/fsl_mdio.c leads in none existent
udevice mdio@3320
instead boards with DM ETH support should use now this
driver.
- remove RFC tag
Commit-notes:
- I let the old none DM based implementation in code
so boards should work with old implementation.
This Code should be removed if all boards are converted
to DM/DTS.
- add the DM based qe uec driver under drivers/net/qe
- Therefore copied the files uccf.c uccf.h uec.h from
drivers/qe. So there are a lot of Codingstyle problems
currently. I fix them in next version if this RFC
patch is OK or it needs some changes.
- The dm based driver code is now under drivers/net/qe/dm_qe_uec.c
Used a lot of functions from drivers/qe/uec.c
- seperated the PHY specific code into seperate file
drivers/net/qe/dm_qe_uec_phy.c
END
The commit 57805f2270 ("net: bcmgenet: Don't set ID_MODE_DIS when
not using RGMII") needed to be extended for the case of using the
rgmii-rxid. The latest version of the Rasbperry Pi4 dtb files for the
5.4 now specify the rgmii-rxid.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Tested-by: Petr Tesarik <ptesarik@suse.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This commit fixes a serious issue occurring when several network
commands are run on a raspberry pi 4 board: for instance a "dhcp"
command and then one or several "tftp" commands. In this case,
packet recv callbacks were called several times on the same packets,
and send function was failing most of the time.
note: if the boot procedure is made of a single network
command, the issue is not visible.
The issue is related to management of the packet ring buffers
(producer / consumer) and DMA.
Each time a packet is received, the ethernet device stores it
in the buffer and increments an index called RDMA_PROD_INDEX.
Each time the driver outputs a received packet, it increments
another index called RDMA_CONS_INDEX.
Between each pair of network commands, as part of the driver
'start' function, previous code tried to reset both RDMA_CONS_INDEX
and RDMA_PROD_INDEX to 0. But RDMA_PROD_INDEX cannot be written from
driver side, thus its value was actually not updated, and only
RDMA_CONS_INDEX was reset to 0. This was resulting in a major
synchronization issue between the driver and the device. Most
visible behavior was that the driver seemed to receive again the
packets from the previous commands (e.g. DHCP response packets
"received" again when performing the first TFTP command).
This fix consists in setting RDMA_CONS_INDEX to the same
value as RDMA_PROD_INDEX, when resetting the driver.
The same kind of fix was needed on the TX side, and a few variables
had to be reset accordingly (c_index, tx_index, rx_index).
The rx_index and tx_index have only 256 entries so the bottom 8 bits
must be masked off.
Originated-by: Etienne Dublé <etienne.duble@imag.fr>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Tested-by: Petr Tesarik <ptesarik@suse.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in
PL and vice versa. That's why change dependencies and do not limit enabling
just for some platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add configuration flag to select the supported dwc driver configuration:
- CONFIG_DWC_ETH_QOS_TEGRA186
- CONFIG_DWC_ETH_QOS_IMX
- CONFIG_DWC_ETH_QOS_STM32
See Linux driver ethernet/stmicro/stmmac and associated glue layers
for other configuration examples.
This patch removes the not-selected compatibles and lets the linker remove
the unused functions to reduce the size of the driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The sgmii mode init flow is almost the same for all mediatek SoC, the
only difference is the register offset(SGMSYS_GEN2_SPEED) is 0x2028
in the old chip(mt7622) but changed to 0x128 for the newer chip(mt7629
and the following chips).
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
The correct setting for the RGMII ports on LS1012ARDB is to
enable delay on both Rx and Tx so the interface mode used should
be PHY_INTERFACE_MODE_RGMII_ID
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Current PFE firmware access spi-nor memory directly. New spi-mem
framework does not support direct memory access. So, let's use
spi_flash_read API to access memory instead of directly using it.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With all the changes in place, add support for DM into the
dc2114x driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Split the common code from the non-DM code, so it can be reused by
the DM code later. As always, the recv() function had to be split
into the actual receiving part and free_pkt part to fit with the
DM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Split the RX data check from the rest of the RX function, so that
the check can be performed separately from the processing of the
packet and the release of the received packet once the processing
is finished.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
The RX/TX DMA descriptor rings are per-device-instance private data,
so move them into the private data.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
This is a trick in preparation for adding DM support. By passing in
the PCI BDF into the phys_to_bus() macros and calling that dev, we
can substitute dev with udevice when DM support lands and do minor
adjustment to the macros to support both DM and non-DM operation.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
This patch replaces the various uses of struct eth_device for accessing
device private data with struct dc2114x_priv, which is compatible both
with DM and non-DM operation.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Introduce dc2114x_priv, which is a super-structure around eth_device
and tracks per-device state and the device IO address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
The current dc21x4x driver accesses its memory mapped registers directly
instead of using the standard I/O accessors. This can cause problems on
some systems as the accesses can get out of order. So convert the direct
volatile dereferences to use the normal in/out macros.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
This code is never used, remove it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Add Kconfig entries for the dc2114x driver and convert various boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
For the usage in this driver, the chips are identical,
so support all of them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Use this macro to fully fill the PCI device ID table. This is mandatory
for the DM PCI support, which checks all the fields.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some code was not converted by coccinelle, somehow.
I manually fixed up the remaining, and comments, README docs.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
[trini: Add arch/arm/mach-davinci/include/mach/sdmmc_defs.h and
include/fdt_support.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
