- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
Add macro fdt_for_each_node_by_compatible() to allow iterating over
fdt nodes by compatible string.
Convert various usages of
off = fdt_node_offset_by_compatible(fdt, start, compat);
while (off > 0) {
code();
off = fdt_node_offset_by_compatible(fdt, off, compat);
}
and similar, to
fdt_for_each_node_by_compatible(off, fdt, start, compat)
code();
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
=HtB+
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
Add support of the MAC controller of Aspeed AST2600 SOC. The MAC
controller is the same with AST2500, except it has stand-alone MDIO
hardware block.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support for DM_MDIO to connect to PHY. For the systems that have a
stand-alone MDIO hardware block, enable CONFIG_DM_MDIO to use driver
model for MDIO devices.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
- Let am335x_evm use the CPSW or PRUSS ethernet.
- Implement timer_get_boot_us in the omap timer driver
- gpmc bitflip, QSPI clock calculation on am437x, da8xx_gpio bugfixes
- Assorted K3 updates
For configurations with gmii2rgmii and external phy the DT nodes link
should be gem->gmii2rgmii->phy. But due to limitation in Linux driver
the DT is mentioned as gem->phy and gmii2rgmii->phy as shown in below DT.
ethernet@ff0c0000 {
compatible = "cdns,zynqmp-gem\0cdns,gem";
status = "okay";
interrupt-parent = <0x04>;
interrupts = <0x00 0x3b 0x04 0x00 0x3b 0x04>;
reg = <0x00 0xff0c0000 0x00 0x1000>;
clock-names = "pclk\0hclk\0tx_clk\0rx_clk\0tsu_clk";
#address-cells = <0x01>;
#size-cells = <0x00>;
#stream-id-cells = <0x01>;
iommus = <0x0d 0x875>;
power-domains = <0x0c 0x1e>;
clocks = <0x03 0x1f 0x03 0x69 0x03 0x2e 0x03 0x32 0x03 0x2c>;
phy-handle = <0x0e>;
phy-mode = "gmii";
xlnx,ptp-enet-clock = <0x00>;
local-mac-address = [ff ff ff ff ff ff];
phandle = <0x4d>;
mdio {
#address-cells = <0x01>;
#size-cells = <0x00>;
phandle = <0x4e>;
ethernet-phy@1 {
reg = <0x01>;
rxc-skew-ps = <0x708>;
txc-skew-ps = <0x708>;
phandle = <0x0e>;
};
gmii_to_rgmii_0@8 {
compatible = "xlnx,gmii-to-rgmii-1.0";
phy-handle = <0x0e>;
reg = <0x08>;
phandle = <0x4f>;
};
};
};
Since same DT is used in Linux and U-Boot we need to workaround this
issue by using the gmii2rgmii node which points to phy and we should
ignore the gem pointing to phy directly.
Do this workaround by updating priv->phydev->node value with
priv->phy_of_node only if it is not valid node.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Link: https://lore.kernel.org/r/641eb13425ffe80e0743f60cf90d0f940577b9e9.1642162085.git.michal.simek@xilinx.com
NXP's mEMAC reference manual, Chapter 6.5.5 "MDIO Ethernet Management
Interface usage", specifies to poll the BSY (0) bit in the CFG/STAT
register to wait until a transaction has finished, not bit 31 in the
data register.
In the Linux kernel, this has already been fixed in commit 26eee0210ad7
("net/fsl: fix a bug in xgmac_mdio").
This patch changes the register in the fman_mdio and fsl_ls_mdio
drivers.
As the MDIO_DATA_BSY define is no longer in use, this patch also removes
its definition from the fsl_memac header.
Signed-off-by: Markus Koch <markus@notsyncing.net>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Reduce the missing phy-handle log message to debug message. It is
possible for ethernet DT node to have no phy-handle e.g. in case
of a fixed-link connection. Furthermore, drop the FEC: prefix,
which is a copy-paste error and rather print the ethernet device
name.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This driver is based on an older downstream TI kernel, with
changes and cleanups to work with mainline device-tree bindings.
Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The sja1105_check_device_id() function contains logic to work without
changing the device tree on reworked boards, one of which I have (the
NXP LS1021A-TSN normally has a SJA1105T, but I have a version with a
resoldered SJA1105Q which is pin compatible). This logic is taken from
the Linux driver.
However this logic gets shortcircuited in U-Boot by an earlier check for
the exact device ID specified in the device tree. So the reworked board
does not probe the SJA1105Q switch. Remove this duplicated logic and let
the automatic device ID detection do its job.
Fixes: f24b666b22 ("net: dsa: add driver for NXP SJA1105 L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
On certain TI SoC, like AM64x there is a CPSW3G which supports 2
external independent MAC ports for single CPSW instance.
It is not possible for Ethernet driver to register more than one port
for given instance.
This patch modifies top level CPSW NUSS as UCLASS_MISC and binds
UCLASS_ETH to individual ports so as to support bring up more than one
Ethernet interface in U-Boot.
Note that there is no isolation in the since, CPSW NUSS is in promisc
mode and forwards all packets to host.
Since top level driver is now UCLASS_MISC, board files would need to
instantiate this driver explicitly.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Perform reset before core initialization.
Standard flow which close to 99% users are using getting all IPs out of
reset that there is no need to reset IP again. This is because of all low
level initialization is done in previous bootloader stage.
In SOM case these IPs are not touched by previous bootloader stage that's
why reset needs to be called before IP is accessed to make sure that it is
in correct state.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Link: https://lore.kernel.org/r/5ae1c85b282d632bb62030f1f24a0065661b9153.1638804318.git.michal.simek@xilinx.com
Xilinx DTS files are using two way how to describe ethernet phy.
The first (already supported) has phy as subnode of gem node.
eth {
phy-handle = <&phy0>;
phy0: ethernet-phy@21 {
...
};
};
The second has mdio subnode (with mdio name) which has phy subnode. This
structure allow hadling MDIO reset signal (based on Linux mdio.yaml)
eth {
phy-handle = <&phy0>;
mdio {
phy0: ethernet-phy@21 {
...
};
};
};
This patch adds support for the second case where mdio subnode
is found driver will look at its parent to find out which gem is handling
MDIO bus.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/6748007f0b6db9554d7a4b52352dce23ca403f9d.1638798796.git.michal.simek@xilinx.com
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
As part of this, we use Kconfig to provide the defaults now that were
done in include/spi_flash.h. We also in some cases change from using
CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in
use anyhow as ENV was not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
The RZ/G2 series uses an external clock as a reference to the AVB.
If this clock is controlled by an external programmable clock,
it must be requested by the consumer or it will not turn on.
In order to do this, update the driver to use bulk enable and
disable functions to enable clocks for boards with multiple clocks.
Signed-off-by: Adam Ford <aford173@gmail.com>
Remove the microchip compatible string and default compatible "cdns,macb"
support both 32-bit and 64-bit DMA access.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Enable DWC IP clock in driver probe, so the MII access is possible even
outside of active network transfers. This is particularly useful when
using 'mii' or 'mdio' commands to explore PHY state, neither of which
works with DWMAC currently due to the disabled clock.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The gpio_request_by_name() returns zero in case of success, however the
conditional return value check in gpio_request_by_name() checks only for
(ret != -ENOENT) and if the condition is true, returns ret outright.
This leads to a situation where successful gpio_request_by_name() return
leads to immediate successful eth_phy_of_to_plat() return as well, and
to skipped parsing of "reset-assert-us" and "reset-deassert-us", so the
PHY driver operates with valid reset GPIO, but with assert/deassert times
set to default, which is 0, instead of the values from DT. This breaks
PHY reset.
Fix this by checking if return value is non-zero and then for this one
single allowed non-zero return value, -ENOENT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Broadcom bnxt L2 driver support. Used by the Broadcom
iproc platforms.
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
It turns out that in custom designs if the system is reset
multiple times in conjunction with a slight increase in external
temperature, the felix switch starts to behave in a strange way:
packets are no longer received on the ENECT interface connected
to the L2switch internal port (the TX side of internal port stops working
or the packets do not reach there. It is not very clear where
the packets remain blocked. None of the counters points to a disruption
in the L2switch)
The issue is not reproducible on NXP reference designs.
It was observed that by adding the switch core reset, the problem
goes aways, even if intensive testing in temperature chambers
is applied.
The current patch performs soft reset on the switch core to ensure proper
operation of the L2switch.
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Some boards need to change the tx/rx delay config in order for
gigabit Ethernet to work.
In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), Realtek documented the bits for overriding the delays
from the hardware straps.
Copy the logic from linux, so the delay config is set from the PHY's
interface type (the phy-mode property in the device tree).
This removes the need for a one-off workaround for the Pine A64+ board.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a driver for the MDIO interface for Aspeed AST2600 SOC. The driver
only supports clause 22 for now.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
redundant_init() is only called in the tsec driver. Make it static.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
priv->promisc is used as the parameter of the set_promisc() call
which accepts a bool type instead of char.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If using OF_CONTROL, fdtcontroladdr is set to the fdt used to configure
U-Boot. When using PXE, if no fdt is defined in the menu file, and
there is no fdt at fdt_addr, add fall back on fdtcontroladdr too.
We are developing board support for the Armv8r64 FVP using
config_distro_bootcmd. We are also using OF_BOARD and would like the
PXE boot option to default to the fdt provided by board_fdt_blob_setup.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
The list of ports which support SGMII depending on switch generation is
available here:
https://www.kernel.org/doc/html/latest/networking/dsa/sja1105.html#port-compatibility-matrix
SGMII can either be used to connect to an external PHY or to the host
port. In the first case, the use of in-band autoneg is expected, in the
last, in-band autoneg is expected to be turned off (fixed-link). So the
driver supports both cases.
SGMII support means configuring the PCS and PMA. The PCS is a Synopsys
Designware XPCS, in Linux this has a separate driver but here it is
embedded within the sja1105 driver. If needed it can be taken out later,
although we would need a UCLASS_PCS for it, which we don't have atm.
Nonetheless, I did go all the way to export an internal MDIO bus for PCS
access, because it is nice to be able to debug the PCS through commands
such as:
=> mdio read ethernet-switch@1-pcs 4 1f.0
Reading from bus ethernet-switch@1-pcs
PHY at address 4:
31.0 - 0x1140
The internal MDIO bus is not registered with DM because there is no
udevice on it, as mentioned. But the XPCS code can still be ripped out,
as needed.
I did not add support for 2500base-x because I do not expect this
interface type to be used as a boot source for anybody, it would just
add unnecessary bloat.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The SJA1105 driver is largely reused from Linux. Its programming model
is that it is blank out of reset, and it waits for a static
configuration stream over SPI, which contains all runtime parameters (it
has no notion of "default values").
Keeping a binary array for the configuration stream would have meant
that aspects such as the CPU port and the MAC speeds could have not been
configured easily, and would have been static and board-dependent.
Live-patching the binary array means recalculating the static config
table CRCs, which is not a fun process.
So we create an abstraction over the static config tables, using the
packing API, same as in Linux. The tables are kept as C structures, and
the binary configuration stream is constructed on-the-go, with CRC and
all.
All static config tables instantiated in this driver are mandatory.
The hardware reference manual can be found at:
https://www.nxp.com/docs/en/user-guide/UM10944.pdf
For tagging, a simplified version of tag_8021q from Linux is used. The
VLAN EtherType is the same (0xdadb) but since we don't want switching in
U-Boot, there is no reason to have a TX VLAN and an RX VLAN for each
port. We just need the RX VLANs to act as the unique pvid of each
front-panel port, to decode the switch port number. The RX VLAN is used
for both RX and TX.
The device tree bindings are the same as in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Instead of trying to guess which operating modes need in-band
negotiation to be active and which ones don't, parse the available
information from the device tree. That will be correct in the cases we
can already guess, and more.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The Freescale TSEC can be a DSA master, and the ports of the attached
DSA switch can have different MAC addresses compared to the TSEC.
Nonetheless, the TSEC must receive the packets on behalf of those switch
ports. Therefore, implement the promiscuous mode method to allow DSA to
set this.
Note that the init_registers() function called from eth_ops :: start
overwrites this setting. There is no reason why the RCTRL register
should be zero-initialized, so just stop clearing it so that the setting
we applied in eth_ops :: set_promisc sticks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The VSC8502 is a Microchip (formerly Microsemi, formerly Vitesse)
dual port, gigabit Ethernet copper PHY which supports the MII, GMII and
RGMII MAC-side interfaces.
Of these, I could only test RGMII, and my board needed RGMII delays to
be applied by software, so I am able to confirm that this patch handles
that properly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYZPDrwAKCRDKSWXLKUoM
IS9GAJ93T/uprhLcKWMb+284YMb2caWgOACfZ02nTlzvZKNNXVretJgZaHXqj1M=
=cwTL
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.01-rc3
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
Use moveconfig.py script to convert CONFIG_SYS_FMAN_FW_ADDR,
CONFIG_SYS_QE_FW_ADDR and CONFIG_SYS_QE_FMAN_FW_LENGTH to Kconfig and
move these entries to defconfigs.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The following warning is seen in macb.c in a 32-bit build:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Change to use dev_read_addr_index_ptr(), or cast with uintptr_t.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will
remove the asm/arch/gpio.h header. In preparation, clean up the various
files that include it.
Some files did not contain any GPIO code at all, so this header was
completely unused.
A few files contained only legacy platform-specific GPIO code for
setting up pin muxes. They were left unchanged, as that code will be
completely removed by the DM_PINCTRL migration.
The remaining files contain some combination of DM_GPIO and legacy GPIO
code. For those, switch to including asm/gpio.h (if it wasn't included
already). Right now, this header provides both sets of functions,
because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the
right header to include once the DM_GPIO migration is complete and
GPIO_EXTRA_HEADER is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
