The total FIFO size of some SoCs may be different from the existen, this
patch supports fifo size setting from platform data.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
- update fastboot_okay() and fastboot_fail()
This file originally came from upstream code.
While retaining the storage abstraction feature, this is the second
set of the changes required to resync with the
cmd_flash_mmc_sparse_img()
in the file
aboot.c
from
https://us.codeaurora.org/cgit/quic/la/kernel/lk/plain/app/aboot/aboot.c?h=LE.BR.1.2.1
Signed-off-by: Steve Rae <srae@broadcom.com>
This "session-id" alogrithm is not required, and currently corrupts
the stored image whenever more the one "session" is required.
Signed-off-by: Steve Rae <srae@broadcom.com>
Define CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8 to allow the
physical interface to be 8-bit (rather than 16-bit).
Signed-off-by: Steve Rae <srae@broadcom.com>
Reported by Coverity:
Logically dead code (DEADCODE)
dead_error_line: Execution cannot reach this statement:
(f_dfu->strings + --i).s = ....
If calloc failed, i is still 0 and no need to call free,
so discard the dead code.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: "Łukasz Majewski" <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Remaining bytes means bytes that are not yet transferred
and not the bytes that were transferred in the last transfer.
Reported-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Steve Rae <srae@broadcom.com>
[Test HW: bcm28155_ap board]
Request size can be greater than ep.packet and still end in a
short packet. We need to tackle this case as end of transfer
(if short_not_ok is not set) as indicated in USB 2.0 Specification [1],
else we get stuck up on certain protocols like fastboot.
[1] - USB2.0 Specification, Section 5.3.2 Pipes
Reported-by: Steve Rae <steve.rae@broadcom.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Steve Rae <steve.rae@broadcom.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Just use ep->maxpacket to get the maxpacket size
and simplify the bulk-out maxpacket alignment.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Steve Rae <srae@broadcom.com>
In a dual speed configuration we need to check at runtime if
we want to enable the Full-Speed or High-Speed endpoint.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Steve Rae <srae@broadcom.com>
[Test HW: bcm235xx board]
wMaxPacketSize for IN endpoing in High-Speed must be 512 and not 64.
While fixing that we do some clean ups like
- use cpu_to_le16(decimal_length) instead of hexadecimal length.
- No need to initialize bInterval to 0. Static variables are 0 initialized.
- Move descriptor setting from fastboot_add to to fastboot_bind.
- check for dual speed configuration before setting the high speed descriptors.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Steve Rae <srae@broadcom.com>
Tested-by: Steve Rae <srae@broadcom.com> [Test HW: bcm235xx board]
While at it, remove obsolete CONFIG_USBDOWNLOAD_GADGET option from some
config headers. This is also probably fixes am335x_baltos board.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Move CONFIG_USB_GADGET_DUALSPEED option to Kconfig and
make all UDC controllers select USB_GADGET_DUALSPEED:
- add next options to Kconfig selecting USB_GADGET_DUALSPEED:
- USB_GADGET_ATMEL_USBA
- USB_GADGET_DWC2_OTG
- USB_DWC3
- CI_UDC
- make USB_MUSB_GADGET select USB_GADGET_DUALSPEED
While at it, make some related fixes:
- remove DUALSPEED from configs that don't enable gadget support:
- kwb.h
- tseries.h
- add missing USB_GADGET option to next configs:
- novena_defconfig
- pcm051_rev*_defconfig
- xfi3_defconfig
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
The description was borrowed from kernel. Definitions were added to
defconfig files in a way that "make savedefconfig" generates exactly
the same file as used defconfig.
Boards using 0 mA as CONFIG_USB_GADGET_VBUS_DRAW value were moved to use
2 mA (as minimal allowed by Kconfig).
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
The USB Mass Storage (ums) works in Windows, Linux and OS X (EL Capitan).
But, not in OS X (Yosemite). By applying the said patch, it extends
the ums support.
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid XU3 (./test/py UMS + DFU tests)
Tested-by: John Tobias <john.tobias.ph@gmail.com>
Linux:
- Run ums to expose all my eMMC partition - shows all correctly
- Run ums to expose only 1 partition of my eMMC - show correctly
Windows:
- Run ums to expose all my eMMC partition - it detects but it prompts,
if I want to format it (due to a non windows partition)
- Run ums to expose only the FAT32 partition - it show the partition
correctly.
Some boards need to expose device specific variable through fastboot
(to adpat the flashing script depending on hardware revision for
example).
Provide a way to expose custom fastboot variables. Note that all
variables meant to be exposed through fastboot should be be prefixed
with 'fastboot.', the variable should not exceed 32 bytes (including
the prefix and the trailing '\0') and the variable content should
fit in the response buffer (60 bytes excluding the 'OKAY' prefix and
the trailing '\0').
Signed-off-by: Rob Herring <rob.herring@linaro.org>
[Boris Brezillon: add a commit message]
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Steve Rae <srae@broadcom.com>
The description was borrowed from kernel. "tristate" type was changed
to "bool" (I believe we don't support modules for u-boot yet, right?).
CONFIG_USB_GADGET requires CONFIG_USB to be defined too, so add it along
as well.
Definitions were added to defconfig files in a way that
"make savedefconfig" generates exactly the same file as used defconfig.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Add zynq_zc702 conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>
In case when usb_composite_register() failed once (for whatever reason),
it will fail further even if all conditions are correct. Example:
=> fastboot 2
Invalid Controller Index
couldn't find an available UDC
g_dnl_register: failed!, error: -19
exit not allowed from main input shell.
=> fastboot 0
g_dnl_register: failed!, error: -22
exit not allowed from main input shell.
Despite that 0 is correct index for USB controller, "fastboot 0" command
will fail, because "composite" structure wasn't cleared properly on
previous fail (on "fastboot 2" command).
This patch fixes that erroneous behavior, allowing us to use composite
even after previous failure.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Fix the formatting in error messages, and demote one error message
to a warning, as it is only informational.
Signed-off-by: Steve Rae <srae@broadcom.com>
This patch fixes situation when one would like to write large file into
medium with the file system (fat, ext4, etc).
This change sets file size limitation to the DFU internal buffer size.
Since u-boot is not supporting interrupts and seek on file systems, it
becomes challenging to store large file appropriately.
To reproduce this error - create large file (around 26 MiB) and sent it
to the target board.
Lets examine the flow of USB transactions:
0. DFU uses EP0 with 64B MPS [Max Packet Size]
1. Send file - OUT (PC->target) - dat_26MiB.img is sent with 4096 B transactions
2. Get status - OUT (PC->target) - wait for DFU_STATE_dfuDNLOAD_IDLE (0x05) sent
from target board - IN transaction
(target->PC)
3. The whole file content is sent to target - OUT (PC->target) with ZLP [Zero
Length Packet]
Now the interesting part starts:
4. OUT (PC->target) Setup transaction (request to share DFU state)
5. IN (target->PC) - reply the current DFU state
- In the UDC driver the req->completion (with dfu_flush) is called
after successful IN transfer.
- The dfu_flush() (called from req->completion callback) saves the
whole file at once (u-boot doesn't support seek on fs).
Such operation takes considerable time. When the file
is large - e.g. 26MiB - this time may be more than 5 seconds.
6. OUT (PC->target) - ZLP, is send in the same time when dfu_flush()
writes data to eMMC memory.
The dfu-util application has hard coded timeout on USB transaction
completion set to 5 seconds (it uses libusb calls).
When the file to store is large (e.g. 26 MiB) the time needed to write it
may excess the dfu-util timeout and following error message will be displayed:
"unable to read DFU status" on the HOST PC console.
This change is supposed to leverage DFU's part responsible for storing files
on file systems. Other DFU operations - i.e. raw/partition write to NAND and
eMMC should work as before.
The only functional change is the error reporting. When dfu_flush() fails
the u-boot prompt will exit with error information and dfu-util application
exits afterwards as well.
Test HW:
- Odroid XU3 (Exynos5433) - test with large file
- Trats (Exynos4210) - test for regression - eMMC, raw,
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reported-by: Alex Gdalevich <agdalevich@axion-biosystems.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Heiko Schocher <hs@denx.de>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
In current high speed fastboot, fs_ep_in.wMaxPacketSize is configured 64 bytes
as default, as a result, it failed to match the size at initialization stage in
usb controller.
Actually, hardware can support less than or equal to 512 bytes in high speed mode,
so I changed the condition from '!=' to '>' to fix this issue.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Tested-by: Steve Rae <srae@broadcom.com>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
All the i.MX6, i.MX23 and i.MX28 OTG controllers only support UTMI
interface. Set to ULPI is not correct, even the controller will
reject this setting in PORTSC register.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.
Simple uses of sprintf are also converted to use strcpy.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Extend the ums command to accept a list of block devices. Each of these
will be exported as a separate LUN. An example use-case would be:
ums 0 mmc 0,0.1,0.2
... which would export LUNs for eMMC 0's user data, boot0, and boot1 HW
partitions. This is useful since it allows the host access to everything
on the eMMC without having to somehow stop the ums command from executing
and restart it with different parameters.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The driver is actually for the Designware DWC2 controller.
This patch renames the global s3c_udc.h header to dwc2_udc.h.
The rename is done automatically:
$ sed -i "s/s3c_udc\.h/dwc2_udc.h/g" \
`git grep "s3c_udc\.h" | cut -d : -f 1`
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch is the second and final to rename global symbol,
the s3c_udc_probe() function.
The rename is done automatically:
$ sed -i "s/s3c_udc_probe/dwc2_udc_probe/g" \
`git grep s3c_udc_probe | cut -d : -f 1`
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch is the first to rename global symbol, the struct
s3c_plat_otg_data.
The rename is done automatically:
$ sed -i "s/s3c_plat_otg_data/dwc2_plat_otg_data/g" \
`git grep s3c_plat_otg_data | cut -d : -f 1`
Signed-off-by: Marek Vasut <marex@denx.de>
The s3c-otg IP block is in fact a DWC2 OTG one, so finally rename the
config option to make it less misleading. No functional change, just
a mechanical change done using the following script:
git grep USB_GADGET_S3C_UDC_OTG | cut -d : -f 1 | sort -u | \
while read line ; do
sed -i "s/USB_GADGET_S3C_UDC_OTG/USB_GADGET_DWC2_OTG/g" $line ;
done
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
Tweak the comments in the driver to reflect this fact.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames the remaining S3C_* macros to match the
DWC2 naming.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames the local source files to dwc2_*c and
adjusts the Makefile to use the new names.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames the local header files to dwc2_*h and
adjusts the sources to use the new names.
Signed-off-by: Marek Vasut <marex@denx.de>
The extern statements are useless, remove them. Also remove the
extern ... controller, which is completely useless.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames the remaining local s3c_*() functions
to reflect this.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames the s3c_ep_*() functions to reflect this.
The function s3c_udc_probe() is a special case and is not
renamed by this patch yet.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames the s3c_ep_*() functions to reflect this.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames the s3c_ep0_*() functions to reflect this.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_request to reflect this.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_ep to reflect this.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_dev_*_ep to reflect this.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_usbotg_phy to struct dwc2_usbotg_phy
to make things more obvious and clear.
Signed-off-by: Marek Vasut <marex@denx.de>
Most of the functions are local to the s3c_udc driver, remove them
from the s3c_udc.h header to stop those bits from propagating all
over the place. Instead, move all the private stuff into new private
s3c_udc_otg_priv.h header.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_usbotg_reg to struct dwc2_usbotg_reg
to make things more obvious and clear.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_udc to struct dwc2_udc to make
things more obvious and clear.
Signed-off-by: Marek Vasut <marex@denx.de>
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
So far the fastboot code was only supporting MMC-backed devices for its
flashing operations (flash and erase).
Add a storage backend for NAND-backed devices.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The fastboot flash command that writes an image to a partition works in
several steps:
1 - Retrieve the maximum size the device can download through the
"max-download-size" variable
2 - Retrieve the partition type through the "partition-type:%s" variable,
that indicates whether or not the partition needs to be erased (even
though the fastboot client has minimal support for that)
3a - If the image is smaller than what the device can handle, send the image
and flash it.
3b - If the image is larger than what the device can handle, create a
sparse image, and split it in several chunks that would fit. Send the
chunk, flash it, repeat until we have no more data to send.
However, in the 3b case, the subsequent transfers have no particular
identifiers, the protocol just assumes that you would resume the writes
where you left it.
While doing so works well, it also means that flashing two subsequent
images on the same partition (for example because the user made a mistake)
would not work withouth flashing another partition or rebooting the board,
which is not really intuitive.
Since we have always the same pattern, we can however maintain a counter
that will be reset every time the client will retrieve max-download-size,
and incremented after each buffer will be flashed, that will allow us to
tell whether we should simply resume the flashing where we were, or start
back at the beginning of the partition.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The functions and a few define to generate a fastboot message to be sent
back to the host were so far duplicated among the users.
Move them all to a common place.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Cast u32 bit value to 64bit before recasting to 64bit pointer to avoid
pointer from integer cast size mismatch warnings.
Warning log:
+../drivers/usb/gadget/udc/udc-core.c: In function
‘usb_gadget_unmap_request’:
+../drivers/usb/gadget/udc/udc-core.c:68:19: warning: cast to pointer
from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch removes this warning:
CC drivers/usb/gadget/f_thor.o
drivers/usb/gadget/f_thor.c: In function ‘thor_tx_data’:
drivers/usb/gadget/f_thor.c:572:2: warning: format ‘%d’ expects argument
of type ‘int’, but argument 4 has type ‘long unsigned int’ [-Wformat=]
debug("%s: dev->in_req->length:%d to_cpy:%d\n", __func__,
^
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The current fastboot support assumes that CONFIG_FASTBOOT_FLASH implies
that we have an MMC in our system, which might not be the case if we have
some other storage device.
Change the configuration option protecting that call to
FASTBOOT_FLASH_MMC_DEV, that makes much more sense.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit 6a13241635 "ci_udc: Update the ci_udc driver to support bulk
transfers" caused the value of "len" to change without updating subsquent
users of that variable in ci_ep_submit_next_request(). This caused the
code that detects when to emit ZLPs (Zero Length Packets) never to
trigger, which in turn caused host timeouts when a ZLP was required,
which in turn broke tests/dfu/, even despite the assertion in that
commit's description that "These changes are tested for both the DFU and
lthor."
Fix this by modifying the added dtd iteration code not to modify "len",
but rather to keep state in a separate variable. Rename the variables
while we're at it so they describe their purpose better.
Fixes: 6a13241635 ("ci_udc: Update the ci_udc driver to support bulk transfers")
Cc: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Implement endpoint dequeue callback function.
Without this function, uboot will hang when executing fastboot comamnd.
See following flow:
"fastboot_tx_write_str->fastboot_tx_write->usb_ep_dequeue->ep->ops->dequeue"
without implement ci_udc dequeue function, ep->ops->dequeue is NULL, then
uboot will hang.
Tested on mx6qsabresd board with fastboot enabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: "Łukasz Majewski" <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
By the time g_dnl_unbind() is run, cdev->config has been set to NULL,
so the free() there does nothing, and the config struct is leaked.
Equally, struct usb_gadget contains a linked list of config structs, so
the code should iterate over them all and free each one, rather than
freeing one particular config struct.
composite_unbind() already iterates over the list of config structs, and
unlinks each from the linked list. Fix this loop to free() each struct as
it's unlinked and otherwise forgotten.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Now that we have a new header file for cache-aligned allocation, we should
move the stack-based allocation macro there also.
Signed-off-by: Simon Glass <sjg@chromium.org>
port at91_udc driver from linux:
original commit Message:
commit c94e289f195e0e13cf34d27f9338d28221a85751
Author: Arnd Bergmann <arnd@arndb.de>
Date: Sat Apr 11 00:14:21 2015 +0200
usb: gadget: remove incorrect __init/__exit annotations
A recent change introduced a link error for the composite
printer gadget driver:
`printer_unbind' referenced in section `.ref.data' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
Evidently the unbind function should not be marked __exit here,
because it is called through a callback pointer that is not necessarily
discarded, __composite_unbind() is indeed called from the error path of
composite_bind(), which can never work for a built-in driver.
Looking at the surrounding code, I found the same problem in all other
composite gadget drivers in both the bind and unbind functions, as
well as the udc platform driver 'remove' functions. Those will break
if anyone uses the 'unbind' sysfs attribute to detach a device from a
built-in driver.
This patch removes the incorrect annotations from all the gadget
drivers.
Signed-off-by: Heiko Schocher <hs@denx.de>
Allocate request up to THOR_PACKET_SIZE not the ep0->maxpacket
as the descriptors data depend on the number of descriptors
and this 64 bytes were not enough and the buffer might overflow
which results in memalign failures later.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Dont perform reset at the end of thor download
if configured to do reset off.
Reset may not be required in all cases and hence
provided an option to do so.
The case would be to download the images to DDR instead
of flash device.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cleaning up order of include files by sorting them alphabetically
keeping in mind to leave common.h on top.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
populate _reset_ callback to the USB ethernet gadget since UDC core
expects every gadget driver to have the reset callback. This shouldn't
be needed once the ethernet gadget driver is adapted to use the
composite driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Ethernet gadget driver can be used both by both SPL and u-boot. Since
usb_eth_init() is the entry point for ethernet gadget driver, perform
board initialization there. Also perform the cleanup in usb_eth_halt.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The ci_udc driver request allocation assumes that the endpoint descriptor
pointer is set to retrieve the endpoint number, but that is only true
when the endpoint is enabled. This results in a NULL ptr dereference
which for me happens to return 0 value. This causes the EP0 request
struct to be returned for other endpoints. Some gadget drivers like
fastboot and USB MS work fine, but ethernet does not.
Really, the ci_udc driver is the oddball here doing this EP0 special
case handling Stephen added. All the other drivers alloc/free functions
are pretty much the same with the only variation being the size of the
private struct. This could all be consolidated to a common function.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
FASTBOOT is defined both by CONFIG_USB_FUNCTION_FASTBOOT AND CONFIG_CMD_FASTBOOT, so it doesn't
make much sense to have a CONFIG_USB_FASTBOOT prefix for fastboot-specific options, especially
given that other config options for fastboot use the CONFIG_FASTBOOT prefix.
This replaces the CONFIG_USB_FASTBOOT prefix with CONFIG_FASTBOOT, for consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Add the required files for the Broadcom UDC OTG interface.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Recent versions of the fastboot tool will query the partition type before doing
an operation on a partition (such as erase, flash, etc). It will then submit
the operation as soon as the response for the partition type is received.
Usually, the MUSB controller will see that the partition type request return
status was read by the host at the very same time as the actual operation
request is submitted by the host. However, the operation will be read first
(int_rx is handled first in musb_interrupt) and after it is completed, the
fastboot USB gadget driver will send another return status. Hence, this happens
before the musb gadget framework has had a chance to handle the previous
acknowledgement that the host read the return status and dequeue the request.
The host will then usually empty the FIFO by the time musb_interrupt gets around
handling the return status acknowledgement (for the previous request, this is
still on the same musb_interrupt call), so no other interrupt is generated and
the most recent return status acknowledgement remains unaccounted for.
It will then be used as a response for the next command, and the proper response
for it will be delayed to the next command, and so on.
Dequeuing the previous IN request in the fastboot code ensures that no previous
return status remains. It is acceptable to do it since there is no callback to
it anyways.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This avoids handling requests that have an error status or no data.
In particular, this avoids showing unnecessary error messages when the USB
gadget gets disconnected (e.g. with fastboot continue) and the fastboot USB
gadget driver sends an error back to the host (that has disconnected already).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Weak versions of board_usb_init and board_usb_cleanup are defined in common USB
host code, but it is also used for USB device gadgets, so we also need a weak
definition of it when there is no USB host enabled.
Both weak definitions do not conflict.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
USB download gadget functions such as thor and dfu have a separate config option
for the USB gadget part of the code, independent from the command part.
This switches the fastboot USB gadget to the same scheme, for better
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
This introduces a coherent scheme for naming USB download gadget and functions
config options. The download USB gadget config option is moved to
CONFIG_USB_GADGET_DOWNLOAD for better consistency with other gadgets and each
function's config option is moved to a CONFIG_USB_FUNCTION_ prefix.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
This change decreases the interval of calls to:
- display busy indicator
- check ctrlc()
- check cable connection
By this change, breaking the UMS command is more easy on Odroid XU3.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Update the ci_udc driver to support bulk transfer
and also added capability of having multiple dtds
if requested data is more than 16K.
These changes are tested for both the DFU and lthor.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.
This cleans up the temporary hacks that were added to this interface
along with the DM support.
This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Use "_ethaddr" at the end of variables and drop CamelCase.
Make constant values actually 'const'.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some controllers support OTG (on-the-go) where they can operate as either
host or device. The gadget layer in U-Boot supports this.
While this layer does not interact with driver model, we can provide a
function which sets up the controller in the correct way. This way the code
at least builds (although it likely will not work).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The "fastboot reboot-bootloader" command is defined to
re-enter into fastboot mode after rebooting into
bootloader. This command is usually used after updating
bootloader via fastboot.
This commit implements only a generic side of the
command - setting of the reset flag and then resetting.
Setting of the reset flag is implemented using __weak
fb_set_reboot_flag() function. The actual setting and
checking of the reset flag should be implemented by
a boot script and/or board/SoC specific code.
Signed-off-by: Alexey Firago <alexey_firago@mentor.com>
Tested-by: Steve Rae <srae@broadcom.com>
[Test HW: bcm28155_ap board]
This patch adds code to select standard, commonly used usb endpoint
configuration (ep1in-bulk, ep2out-bulk, ep3in-int) to dwc3 driver. This
ensures compatibility with old userspace and windows drivers, which
expects hardcoded endpoint numbers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
DWC3 UDC driver requires presence of .reset callback in a composite driver.
This setting is similar to the one nowadays present in linux kernel.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Since we support multiple dwc3 controllers to be existent at the same
time, in order to handle the interrupts of a particular dwc3 controller
usb_gadget_handle_interrutps should take controller index as an
argument.
Hence the API of usb_gadget_handle_interrupts is modified to take
controller index as an argument and made the corresponding changes to all
the usb_gadget_handle_interrupts calls.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Taken from linux kernel with commit
commit 765f5b830e547229bb752e7b232ee83e2b3d49d5
Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date: Thu Jun 23 14:26:11 2011 +0200
usb: gadget: defer setting maxpacket till ->setup()
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Now that the entire dwc3 driver is adapted to compile with uboot build,
modify the Makefiles so that the dwc3 driver can be built.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Make udc-core compile in u-boot by removing all linux specific
stuff and having only the bare minimal udc-core required for
usb gadget drivers. Also modified the file header to a format that is
generally being used in u-boot.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added udc-core.c from linux kernel 3.19-rc1 (97bf6af1f9) to u-boot.
This will be adapted to work with u-boot in the
following patches.
Adding support for udc will help to seamlessly port dwc3 driver from
linux kernel to u-boot (since dwc3 uses udc-core) and it'll also help
to add support for multiple gadget controllers to be functional at the
same time.
All other gadget drivers can also be adapted to use udc-core.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: "Łukasz Majewski" <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Some ethernet drivers use their own version of ethernet FCS length
macro which is really common. We define ETH_FCS_LEN in net.h and
replace those custom versions in various places.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Configure the serial number using the serial# environment variable
during the fastboot bind.
This enables "fastboot devices" to return the serial number for
the attached devices.
Signed-off-by: Dileep Katta <dileep.katta@linaro.org>
Acked-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
OUT transactions must be aligned to wMaxPacketSize for each transfer,
or else transfer will not complete successfully. This patch modifies
rx_bytes_expected to return a transfer length that is aligned to
wMaxPacketSize.
Note that the value of wMaxPacketSize and ep->maxpacket may not be
the same value, and it is the value of wMaxPacketSize that should be
used for alignment. wMaxPacketSize is passed depending on the speed of
connection.
Signed-off-by: Dileep Katta <dileep.katta@linaro.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Adds the fastboot erase functionality, to erase a partition
specified by name. The erase is performed based on erase group size,
to avoid erasing other partitions. The start address and the size
is aligned to the erase group size for this.
Currently only supports erasing from eMMC.
Signed-off-by: Dileep Katta <dileep.katta@linaro.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Add "oem format" command to write partition table. This relies on the
env variable partitions to contain the list of partitions as required by
the gpt command.
Note that this does not erase any data other than the partition table.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Steve Rae <srae@broadcom.com>
Add code stub to handle "fastboot oem __" command. As unlock is a common
fastboot command, distinguish that it is not implemented.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Steve Rae <srae@broadcom.com>
Fix use-before-initialized bug in pxa25x_udc driver.
Function usb_gadget_register_driver calls udc_disable,
and udc_disable calls pullup_off that uses dev->mach->udc_command.
But dev->mach is initialized in usb_gadget_register_driver after
calling udc_disable. This patch fixes the order of initialization.
Signed-off-by: Alex Sadovsky <Nable.MainInbox@googlemail.com>
Without this function the USB compliance test (USB 2.0 Command Verifier) will
fail in the "Interface Descriptor Test" with this error message:
FAIL
(1.2.51) A successful GetInterface request must return the alternate setting
set by a prior call to SetInterface.
Lets add this function to read back the value so that the DFU device fully
passes the USB compliance test.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Enrico Leto <enrico.leto@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
On the DXR2 board (AM335x using MUSB) the USB compliance test suite
(USB 2.0 Command Verifier) will cause the board to crash and reset
upon the "BOS Descriptor Test - Addressed state". Here the output
from the DRX2 while running this test:
GADGET DRIVER: usb_dnl_dfu
musb-hdrc: peripheral reset irq lost!
composite_setup (776)
data abort
pc : [<87f693ac>] lr : [<87f6911c>]
sp : 86f33a58 ip : 00000000 fp : 86f3bbac
r10: 00000f00 r9 : 86f33ef4 r8 : 86f37da8
r7 : 00000005 r6 : 86f33a90 r5 : 00000000 r4 : 86f37e30
r3 : 00000000 r2 : 00000000 r1 : 87f9c888 r0 : 00000016
Flags: Nzcv IRQs off FIQs on Mode SVC_32
Resetting CPU ...
resetting ...
By adding the case statement for USB_DT_BOS and therefore not running
into the default case (jump to unkown label) this crash is fixed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Enrico Leto <enrico.leto@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Some pointers in function download_tail() were not checked
before the use. This could possibly cause the data abort.
To avoid this, check if the pointers are not null is added.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[TestHW: Exynos4412-Trats2]
The fastboot continue command is defined to exit fastboot and continue
autoboot. This commit implements the continue command and the exiting of
fastboot only. Subsequent u-boot commands can be processed after exiting
fastboot. Autoboot should implement a boot script such as "fastboot; mmc
read <...>; bootm" to fully implement the fastboot continue function.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[TestHW: Exynos4412-Trats2]
In order to add detach functions for fastboot, make the DFU detach related
functions common so they can be shared.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[TestHW: Exynos4412-Trats2]
When receive data, the RXRDY in status register set by hardware
after a new packet has been stored in the endpoint FIFO. After,
we copy from FIFO, we clear it, make the FIFO can be accessed
again.
In the receive_data() function, this bit RXRDY has been cleared.
So, after the receive_data() function return, this bit should
not be cleared again, or else it will cause the accessing FIFO
corrupt, which will make the data loss.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Move strlcpy() definition from drivers/usb/gadget/ether.c to
lib/string.c because it is a very useful function.
Let's add the prototype to include/linux/string.h too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
Split the Samsung specific PHY control into a separate file
and compile this into the S3C OTG driver only if used on a
Samsung system.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Encapsulate the Samsung PHY control and its register accesses
into the otg_phy_init() and otg_phy_off() functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Remove the useless inclusion of arch/arm/gpio.h , which is completely
bogus in this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Without NULL termination, various commands will read past the
end of input. In particular, this was noticed with error()
calls in cb_getvar and simple_strtoul() in cb_download.
Since the download callback happens elsewhere, the 4k buffer
should always be sufficient to handle command arguments.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
The processing of the max-download-size variable requires a
radix specifier, or the fastboot host tool will interpret
it as an octal number.
See function get_target_sparse_limit() in file fastboot/fastboot.c
in the AOSP:
https://android.googlesource.com/platform/system/core/+/master
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Current Android Fastboot seems to use 'max-download-size' instead
of 'downloadsize' variable to indicate the maximum size of sparse
segments.
See function get_target_sparse_limit() in file fastboot/fastboot.c
in the AOSP:
https://android.googlesource.com/platform/system/core/+/master
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Force full-speed (12 Mbit/s) operation if CONFIG_USB_GADGET_DUALSPEED
is not defined.
The controller is capable of high-speed (480 Mbit/s) operation,
but some designs may require the use of lower-speed operation.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
When download is ongoing, if the actual size of one transfer
is not the same as BYTES_PER_DOT, which will cause the dot
won't print anymore. Then it will let the user thinking it
is stuck, actually it is transfering without dot printed.
So, improve the method to show the progress bar (print dot).
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Marek Vasut <marex@denx.de>
Without this flag, tools like Alex Page's USB Image Tool
won't see drives exposed over USB Gadget as removable,
and won't allow access to them.
http://www.alexpage.de/usb-image-tool/
The code was pulled from the main-line kernel:
drivers/usb/gadget/function/f_mass_storage.c
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
DFU now can use also fullspeed.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Liu Bin <b-liu@ti.com>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
- update static function
- additional debugging statements
- update "fastboot command" information
- add missing include file
- update spelling
Signed-off-by: Steve Rae <srae@broadcom.com>
- implement 'fastboot flash' for eMMC devices
Signed-off-by: Steve Rae <srae@broadcom.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Marek Vasut <marex@denx.de>
When enable debug option to compile, it will give the following
warning, this patch is used to get rid of it.
--->8---
warning: 'flags' is used uninitialized in this function [-Wuninitialized]
---8<---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
When enable debug option to compile, it will give the following
warning, this patch is used to get rid of it.
--->8---
warning: 'flags' is used uninitialized in this function [-Wuninitialized]
---8<---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
This allows the USB code to determine whether a USB bus reset was issued,
which in turn allows the code to differentiate between a detach (return
to shell prompt) and a board reset/reboot request.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
New dfu_usb_get_reset() method is necessary to distinct two different
use cases of dfu-util program.
This method checks if the USB bus reset has been really performed after
DFU DETACH.
Without this function the previous DFU behavior is preserved.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
This commit provides distinction between DFU device detach and reset.
The -R behavior is preserved with proper handling of the dfu-util's -e
switch, which detach the DFU device.
By running dfu-util -e; one can force device to finish the execution of
dfu command on target and execute some other scripted commands.
Moreover, some naming has been changed - the dfu_reset() method now is known
as dfu_detach(). New name better reflects the purpose of the code.
It was also necessary to increase the number of usb_gadget_handle_interrupts()
calls since we also must wait for detection of the USB reset event.
Example usage:
1. -e (detach) switch
dfu-util -a0 -D file1.bin;dfu-util -a3 -D uImage;dfu-util -e
access to u-boot prompt.
2. -R (reset) switch
dfu-util -a0 -D file1.bin;dfu-util -R -a3 -D uImage
target board reset
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
- move linux specific defines from usb and video code
into linux/compat.h
- move common linux specific defines from include/ubi_uboot.h
to linux/compat.h
- add for new mtd/ubi/ubifs sync new needed linux specific
defines to linux/compat.h
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
[trini: Add spin_lock_irqsave/spin_unlock_irqrestore dummies from
usb/lin_gadet_compat.h]
Signed-off-by: Tom Rini <trini@ti.com>
Emails to the board maintainer
"Rishi Bhattacharya <rishi@ti.com>"
have been bouncing.
Tom suggested to remove this board.
Remove also omap1510_udc.c because this is the last board
to enable it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
The following configs are not defined at all.
- CONFIG_OMAP1510
- CONFIG_OMAP_1510P1
- CONFIG_OMAP_SX1
- CONFIG_OMAP3_DMA
- CONFIG_OMAP3_ZOOM2
- CONFIG_OMAP_INNOVATOR
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
CONFIG_SYS_DFU_DATA_BUF_SIZE may be large to allow for FAT/ext layouts
to transfer large files. However, this means that individual write
operations will take a long time. Allow backends to specify a maximum
buffer size, so that each write operation is limited to a smaller data
block. This prevents the DFU protocol from timing out when e.g. writing
to SPI flash. I would guess that NAND might benefit from setting this
value too, but I can't test that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Fix calls to dfu_write() and dfu_flush() to detect errors in the I/O
itself. This could happen due to problems with the storage medium, or
simply when trying to write a FAT/ext file that is larger than the buffer
dfu_mmc.c maintains for this purpose.
Signal the error by switching the DFU state/status. This will be picked
up by the DFU client when it sends the next DFU request. Note that errors
can't simply be returned from e.g. dnload_request_complete(), since that
function has no way to pass errors back to the DFU client; a call to
dnload_request_complete() simply means that a USB OUT completed.
This error state/status needs to be cleared when the next DFU client
connects. While there is a DFU_CLRSTATUS request, no DFU client seems to
send this. Hence, clear this when selecting the USB alternate setting on
the USB interface.
Finally, dfu.c relies on a call to dfu_flush() to clear up the internal
state of the write transaction. Now that errors in dfu_write() are
detected, dfu_flush() may no longer be called for every transaction.
Separate out the cleanup code into a new function, and call it whenever
dfu_write() fails, as well as from any call to dfu_flush().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Almost all of ci_udc.c uses variable name "ep" for a struct usb_ep and
"ci_ep" for a struct ci_ep. This is nice and consistent, and helps people
know what type a variable is without searching for the declaration.
handle_ep_complete() doesn't do this, so fix it to be consistent.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
A UDC's alloc_request method should zero out the newly allocated request.
Ensure the Atmel driver does so. This issue was found by code inspection,
following the investigation of an intermittent issue with ci_udc, which
was tracked down to failing to zero out allocated requests following some
of my changes. All other UDC drivers already zero out requests in one
way or another.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
struct ci_req is a purely software structure, and needs no specific
memory alignment. Hence, allocate it with calloc() rather than
memalign(). The use of memalign() was left-over from when struct ci_req
was going to hold the aligned bounce buffer, but this is now dynamically
allocated.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
There's no need to store an array of QTD pointers in the controller.
Since the calculation is so simple, just have ci_get_qtd() perform it
at run-time, rather than pre-calculating everything.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2 QTDs are allocated for each EP. The current allocation scheme aligns
the first QTD in each pair, but simply adds the struct size to calculate
the second QTD's address. This will result in a non-cache-aligned
addresss IF the system's ARCH_DMA_MINALIGN is not 32 bytes (i.e. the
size of struct ept_queue_item).
Similarly, the original ilist_ent_sz calculation aligned the value to
ARCH_DMA_MINALIGN but didn't take the USB HW's 32-byte alignment
requirement into account. This doesn't cause a practical issue unless
ARCH_DMA_MINALIGN < 32 (which I suspect is quite unlikely), but we may
as well fix the code to be explicit, so it's obviously completely
correct.
The new value of ILIST_ENT_SZ takes all alignment requirements into
account, so we can simplify ci_{flush,invalidate}_qtd() by simply using
that macro rather than calling roundup().
Similarly, the calculation of controller.items[i] can be simplified,
since each QTD is evenly spaced at its individual alignment requirement,
rather than each pair being aligned, and entries within the pair being
spaced apart only by structure size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This will allow functions other than ci_udc_probe() to make use of the
constants in a future change.
This in turn requires converting the const int variables to #defines,
since the initialization of one global const int can't depend on the
value of another const int; the compiler thinks it's non-constant if
that dependency exists.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Fix ci_ep_submit_next_request()'s ZLP transmission code to explicitly
call ci_get_qtd() to find the address of the other QTD to use. This
will allow us to correctly align each QTD individually in the future,
which may involve leaving a gap between the QTDs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
ci_udc_probe() initializes a pair of QHs and QTDs for each EP. After
each pair has been initialized, the pair is cache-flushed. The
conversion from QH/QTD index [0..2*NUM_END_POINTS) to EP index
[0..NUM_ENDPOINTS] is incorrect; it simply subtracts 1 (which yields
the QH/QTD index of the first entry in the pair) rather than dividing
by two (which scales the range). Fix this.
On my system, this avoids cache debug prints due to requests to flush
unaligned ranges. This is caused because the flush calls happen before
the items[] array entries are initialized for all but EP0.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
cb_getvar tries to prevent overflowing the response buffer
by using strncat. But strncat takes the number of data bytes
copied as a limit not the total buffer length so it can still
overflow. Pass the correct value instead.
cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
cc: Rob Herring <robh@kernel.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
since ALLOC_CACHE_ALIGN_BUFFER defines a pointer and not a
buffer, the memset with sizeof(rqt) likely does something else
then intended. Since there is a memcpy directly after it with
the full size, drop the memset completely.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Since the struct fsg_common is calloced, reset it completely
with zero's when reused. While at it, make checkpatch happy.
cc: Lukasz Majewski <l.majewski@samsung.com>
cc: Piotr Wilczek <p.wilczek@samsung.com>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
ci_udc.c's usb_gadget_unregister_driver() doesn't call driver->unbind()
unlike other USB gadget drivers. Fix it to do this.
Without this, when ether.c's CDC Ethernet device is torn down,
eth_unbind() is never called, so dev->gadget is never set to NULL.
For some reason, usb_eth_halt() is called both at the end of the first
use of the Ethernet device, and prior to any subsequent use. Since
dev->gadget is never cleared, all calls to usb_eth_halt() attempt to
stop, disconnect, and clean up the device, resulting in double cleanup,
which hangs U-Boot on my Tegra device at least.
ci_udc allocates its own singleton EP0 request object, and cleans it up
during usb_gadget_unregister_driver(). This appears necessary when using
the USB gadget framework in U-Boot, since that does not allocate/free
the EP0 request. However, the CDC Ethernet driver *does* allocate and
free its own EP0 requests. Consequently, we must protect
ci_ep_free_request() against double-freeing the request.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Sometimes, a zero-length packet is required at the end of an IN
transaction so that the host knows the device is done sending data.
Enhance ci_udc to send a zlp when necessary. See the comments for
more details.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
usb_gadget_unregister_driver() is called to tear down the USB device mode
stack. Fix the driver to stop the USB HW (which causes any attached host
to notice the disappearance of the device), and free all allocations
(which obviously prevents memory leaks).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
ci_ep_alloc_request() avoids allocating multiple request objects for ep0
by keeping a record of the first req allocated for ep0, and always
returning that instead of allocating a new req. However, if this req is
ever freed, the record of the previous allocation is not cleared, so
ci_ep_alloc_request() will keep returning this stale pointer. Fix
ci_ep_free_request() to clear the record of the previous allocation.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
ci_pullup()'s !is_on path contains a cut/paste copy of udc_disconnect().
Remove the duplication by simply calling udc_disconnect() instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
handle_setup() currently assumes that the response to a Setup transaction
will be an OUT transaction, and any subsequent packet (if any) will be an
IN transaction. This appears to be valid in many cases; both USB
enumeration and Mass Storage work OK with this restriction. However, DFU
uses ep0 to transfer data in both directions. This renders the assumption
invalid; when sending data from device to host, the Data Stage is an IN
transaction, and the Status Stage is an OUT transaction. Enhance
handle_setup() to deduce the correct direction for the USB transactions
based on Setup transaction data.
ep0's request object only needs to be automatically re-queued when the
Data Stage completes, in order to implement the Status Stage. Once the
Status Stage transaction is complete, there is no need to re-queue the
USB request, so don't do that.
Don't sent USB request completion callbacks for Status Stage transactions.
These were queued by ci_udc itself, and only serve to confuse the USB
function code. For example, f_dfu attempts to interpret the 0-length data
buffers for Status Stage transactions as DFU packets. These buffers
contain stale data from the previous transaction. This causes f_dfu to
complain about a sequence number mismatch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Allocate ep0's USB request object when the UDC driver is probed. This
solves a couple of issues in the current code:
a) A request object always exists for ep0. Prior to this patch, if setup
transactions arrived in an unexpected order, handle_setup() would need
to reply to a setup transaction before any ep0 usb_req was created.
This issue was introduced in commit 2813006fec "usb: ci_udc: allow
multiple buffer allocs per ep."
b) handle_ep_complete no longer /has/ to queue the ep0 request again
after every single request completion. This is currently required, since
handle_setup() assumes it can find some request object in ep0's request
queue. This patch doesn't actually stop handle_ep_complete() from always
requeueing the request, but the next patch will.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
ci_udc currently points ep->desc at separate descriptors for IN and OUT.
These descriptors only differ in the ep address IN/OUT field. Modify the
code to use a single descriptor, and change that descriptor's ep address
to indicate IN/OUT as required. This removes some data duplication.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The flipping of ep0 between IN and OUT relies on ci_ep_queue() consuming
the current IN/OUT setting immediately. If this is deferred to a later
point when the req is pulled out of ci_req->queue, then the IN/OUT
setting may have been changed since the req was queued, and state will
get out of sync. This condition doesn't occur today, but could if bugs
were introduced later, and this error-check will save a lot of debugging
time.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Since dfu_flush() can write raw data, dfu_write() with zero size
can be removed from download_tail() in thor gadget.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
ci_udc only allocates a single QTD structure per EP. All data needs to be
extracted from the DTD prior to calling ci_ep_submit_next_request(), since
that fills the QTD with next transaction's parameters. Fix
handle_ep_complete() to extract the transaction (remaining) length before
kicking off the next transaction.
In practice, this only causes writes to UMS devices to fail for me. I may
have tested the final versions of my previous ci_udc patch only with
reads. More recently, I had patches applied locally that allocated a QTD
per USB request rather than per USB EP, although since that doesn't give
any performance benefit, I'm dropping those.
Fixes: 2813006fec ("usb: ci_udc: allow multiple buffer allocs per ep")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
add a possibility to add a medium specific polltimeout
function. So it is possible to define different
poll timeouts.
Used on nand medium, for setting the DFU_MANIFEST_POLL_TIMEOUT
only on nand ubi partitions, which is currently the only
usecase.
Change-Id: If1db5f49b32d93fefa7481e8dfe5b7ccc0e65af4
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
This patch contains an implementation of the fastboot protocol on the
device side and documentation. This is based on USB download gadget
infrastructure. The fastboot function implements the getvar, reboot,
download and reboot commands. What is missing is the flash handling i.e.
writting the image to media.
v3 (Rob Herring):
This is based on http://patchwork.ozlabs.org/patch/126798/ with the
following changes:
- Rebase to current mainline and updates for current gadget API
- Use SPDX identifiers for licenses
- Traced the history and added missing copyright to cmd_fastboot.c
- Use load_addr/load_size for transfer buffer
- Allow vendor strings to be optional
- Set vendor/product ID from config defines
- Allow Ctrl-C to exit fastboot mode
v4:
- Major re-write to use the USB download gadget. Consolidated function
code to a single file.
- Moved globals into single struct.
- Use puts and putc as appropriate.
- Added CONFIG_USB_FASTBOOT_BUF_ADDR and CONFIG_USB_FASTBOOT_BUF_SIZE to
set the fastboot transfer buffer.
v5:
- Add CONFIG option documentation to README
- Rebase using new downloader registration
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Now that the ci_udc driver supports allocating multiple requests per
endpoint, we can revert the special-case added by a022c1e13c "usb:
ums: use only 1 buffer for CI_UDC".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Modify ci_ep_alloc_request() to return a dynamically allocated request
object, rather than a singleton that's part of the endpoint. This
requires moving various state from the endpoint structure to the request
structure, since we need one copy per request.
The "fast bounce buffer" b_fast is removed by this change rather than
moved to the request object. Instead, we enhance the bounce buffer logic
in ci_bounce()/ci_debounce() to keep the bounce buffer around between
request submissions. This avoids the need to allocate an arbitrarily-
sized bounce buffer up-front, yet avoids incurring the allocation
overhead each time a request is submitted.
A future enhancement would be to actually submit multiple requests to HW
at once. The Linux driver shows that this is possible. That might improve
throughput (depending on the USB protocol in use), since USB could be
performing a transfer to one HW buffer in parallel with whatever SW
actions U-Boot performs on another buffer. However, I have not made this
change as part of this patch, in order to keep SW changes related to
buffer management separate from any change in the way the HW is
programmed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
g_dnl_register() currently first attempts to register a composite
driver by name, and then saves the driver name once it's registered.
Internally to the registration code, g_dnl_do_config() is called and
attempts to compare the composite device's name with the list of known
device names. This fails since the composite device's name has not yet
been stored. This means that the first time "ums 0 0" is run, it fails,
but subsequent attempts succeed.
Re-order the name-saving and registration code to solve this.
Fixes: e5b834e07f51 ("USB: gadget: added a saner gadget downloader registration API")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Preprocessor definitions and hardcoded implementation selection in
g_dnl core were replaced by a linker list made of (usb_function_name,
bind_callback) pairs.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
Former usb_cable_connected() patch broke compilation of boards which do
not support this feature.
I've renamed usb_cable_connected() to g_dnl_usb_cable_connected() and added
its default implementation to gadget downloader driver code. There's
only one driver of this kind and it's unlikely there'll be another, so
there's no point in keeping it in /common.
Previously this function was declared in usb.h. I've moved it, since
it's more appropriate to keep it in g_dnl.h - usb.h seems to be intended
for USB host implementation.
Existing code, confronted with default -EOPNOTSUPP return value,
continues as if the cable was connected.
CONFIG_USB_CABLE_CHECK was removed.
Change-Id: Ib9198621adee2811b391c64512f14646cefd0369
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Allow ci_udc.o to be built when using the new(?) USB gadget framework,
as enabled by CONFIG_USB_GADGET.
Note that this duplicates the Makefile entry for ci_udc.o, since it's
also included inside #ifdef CONFIG_USB_ETHER. I'm not sure what that
define means; perhaps an old style of Ethernet-specific USB gadget
implementation?
I wonder if the line that this patch adds shouldn't be outside all of
the ifdefs, so it stands on its own, similar to how e.g. epautoconf.o
is shared between the two?
Signed-off-by: Stephen Warren <swarren@nvidia.com>
ci_udc.c allocates only a single buffer for each endpoint, which
ci_ep_alloc_request() returns as a hard-coded value rather than
dynamically allocating. Consequently, storage_common.c must limit
itself to using a single buffer at a time. Add a special case
to the definition of FSG_NUM_BUFFERS for this.
Another option would be to fix ci_ep_alloc_request() to dynamically
allocate the buffers like some/all(?) other device mode drivers do.
However, I don't think that ci_ep_queue() supports queueing up
multiple buffers either yet, and I'm not familiar enough with the
controller yet to implement that. As such, any attempt to use multiple
buffers simply results in data corruption and other errors.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra's USB controller appears to be a variant of the ChipIdea
controller; perhaps derived from it, or simply a different version of
the IP core to what U-Boot supports today.
In this variant, at least the following difference are present:
- Some registers are moved about.
- Setup transaction completion is reported in a separate 'epsetupstat'
register, rather than in 'epstat' (which still exists, perhaps for
other transaction types).
- USB connection speed is reported in a separate 'hostpc1_devlc'
register, rather than 'portsc'.
- The registers used by ci_udc.c begin at offset 0x130 from the USB
register base, rather than offset 0x140. However, this is handled
by the associated EHCI controller driver, since the register address
is stored in controller.ctrl->hcor.
Introduce define CONFIG_CI_UDC_HAS_HOSTPC to indicate which variant of
the controller should be supported. The "HAS_HOSTPC" part of this name
mirrors the similar "has_hostpc" field used by the Linux EHCI controller
core to represent the presence/absence of the hostpc1_devlc register.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
usb_gadget_register_driver() currently unconditionally programs PORTSC
to select a ULPI PHY. This is incorrect on at least the Tegra boards I
am testing with, which use a UTMI PHY for the OTG ports. Make the PHY
selection code conditional upon the specific EHCI controller that is in
use.
Ideally, I believe that the PHY initialization code should be part of
ehci_hcd_init() in the relevant EHCI controller driver, or some board-
specific function that ehci_hcd_init() calls.
For MX6, I'm not sure this PHY initialization code is correct even before
this patch, since ehci-mx6's ehci_hcd_init() already configures PORTSC to
a board-specific value, and it seems likely that the code in ci_udc.c is
incorrectly undoing this. Perhaps this is not an issue if the PHY
selection register bits aren't implemented on this instance of the MX6
USB controller?
ehci-mxs.c doens't appear to touch PORTSC, so this code is likely still
required there.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
At least drivers/usb/gadget/storage_common.c expects that ep->req.actual
contain the number of bytes actually transferred. (At least in practice,
I observed it failing to work correctly unless this was the case).
However, ci_udc.c modifies ep->req.length instead. I assume that .length
is supposed to represent the allocated buffer size, whereas .actual is
supposed to represent the actual number of bytes transferred. In the OUT
transaction case, this may happen simply because the host sends a smaller
packet than the max possible size, which is quite legal. In the IN case,
transferring fewer bytes than requested could presumably happen as an
error.
Modify handle_ep_complete() to write to .actual rather than modifying
.length.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
ci_ep_queue() currently only fills in the page0/page1 fields in the
queue item. If the buffer is larger than 4KiB (unaligned) or 8KiB
(page-aligned), then this prevents the HW from knowing where to write
the balance of the data.
Fix this by initializing all 5 pageN pointers, which allows up to
16KiB (potentially non-page-aligned) buffers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Allow a NULL table to be passed to usb_gadget_get_string for cases
when a string table may not be populated.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Since dfu read/write operations needs to be flushed manually,
writing to filesystem on MMC by thor was broken. MMC raw write
actually is working fine because current dfu_flush() function
writes filesystem only. This commit adds dfu_flush() to f_thor
and now filesystem write is working.
This change was tested on Trats2 board.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
In thor's download_tail() function, dfu_get_entity() is called
before each dfu_write() call and the returned entity pointers
are the same. So dfu_get_entity() can be called just once and
this patch changes this.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
on nand flash using ubi, after the download of the new image into
the flash, the "rest" of the nand sectors get erased while flushing
the medium. With current u-boot version dfu-util may show:
Starting download: [##################################################] finished!
state(7) = dfuMANIFEST, status(0) = No error condition is present
unable to read DFU status
as get_status is not answered while erasing sectors, if erasing
needs some time.
So do the following changes to prevent this:
- introduce dfuManifest state
According to dfu specification
( http://www.usb.org/developers/devclass_docs/usbdfu10.pdf ) section 7:
"the device enters the dfuMANIFEST-SYNC state and awaits the solicitation
of the status report by the host. Upon receipt of the anticipated
DFU_GETSTATUS, the device enters the dfuMANIFEST state, where it
completes its reprogramming operations."
- when stepping into dfuManifest state, sending a PollTimeout
DFU_MANIFEST_POLL_TIMEOUT in ms, to the host, so the host
(dfu-util) waits the PollTimeout before sending a get_status again.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
The mv_udc is not marvell-specific anymore. The mv_udc is used to drive
generic ChipIdea CI13xxx series OTG cores, so rename the driver to ci_udc
instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
Apparently debug memset (with a 0x55 value) has been overlooked in the
f_thor code.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Now it is possible to allocate static request - which receives data from
the host (OUT transaction) to the size of THOR packet.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
The Samsung's UDC driver is not anymore copying data from USB requests to
aligned internal buffers. Now it works directly in data allocated in the
upper layers like UMS, DFU, THOR.
This change is possible since those gadgets now must take care to allocate
buffers aligned to cache line (CONFIG_SYS_CACHELINE_SIZE).
This can be achieved by using DEFINE_CACHE_ALIGN_BUFFER() or
ALLOC_CACHE_ALIGN_BUFFER() macros. Those take care to allocate buffer
aligned to cache line in both starting address and its size.
Sometimes it is enough to just use memalign() with size being a
multiplication of cache line size.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurement:
Transmission speed: 27.04 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
This patch removed obscure restriction on the HW setting of DMA transfers.
Before this change each transaction sent up to 512 bytes (with packet count
equal to 1) for non EP0 transfer.
Now it is possible to setup DMA transaction up to DMA_BUFFER_SIZE.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurement:
Transmission speed: 20.74 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
A set of cache operations (both invalidation and flush) were redundant
in the S3C HS OTG Samsung driver:
1. s3c_udc_ep0_zlp - to transmit EP0's ZLP packets one don't need to flush
the cache (since it is the zero length transmission)
2. s3c_udc_pre_setup and s3c_ep0_complete_out - cache invalidation is not
needed when the buffer for OUT EP0 transmission is setup, since no data
has yet arrived.
Cache cleanups presented above don't contribute much to transmission speed
up, hence shall be regarded as cosmetic changes.
3. setdma_rx - here the s3c UDC driver's internal buffers were invalidated.
This call is not needed anymore since we reuse the buffers passed from
gadgets. This is a key contribution to transmission speed improvement.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurements:
Base values (without improvement):
Transmission speed: 9.51 MiB/s
After the change:
Transmission speed: 10.15 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Calls to malloc() have been replaced by memalign. It now provides proper
buffer alignment.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
The fifo size of ep0 is 64 bytes, and if the packet size grater than
64 bytes, the driver would have to fill up the fifo multiple times,
and before filling up the fifo, the driver should make sure the fifo
is empty by checking fifo empty indication.
However there is a hardware bug that the fifo empty indication is
somehow a bit earlier than fifo reset. So if I don't add an extra
delay here, the data might be corrupted. (i.e., 1 byte missing)
After a couple of tests, it truns out that 1 usec is good enough.
This workaround should be applied to all hardware revisions.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
Since hardware revision 1.11.0, the following interrupt status
registers are now W1C (i.e., write 1 clear):
1. Interrupt Source Group 0 Register (0x144) (EP0 Abort: BIT5)
2. Interrupt Source Group 2 Register (0x14C) (All bits)
And before revision 1.11.0, these registers are all R/W.
Which means software must write a 0 to clear the status.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
It is necessary to deter the host from sending subsequent DFU_GETSTATUS
request in the case of e.g. writing the buffer to medium.
Here the timeout is increased when we fill up the whole buffer. This delay
allows eMMC memory to perform its internal operations.
Otherwise we end up with HOST's error regarding GET_STATUS receive timeout.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Before switching to the real Kbuild, drivers/usb/gadget/Makefile
must be fixed.
If none of CONFIG_USB_GADGET, CONFIG_USB_ETHER, CONFIG_USB_DEVICE
is defined, both obj- and obj-y get empty.
We need non-empty obj- or obj-y on each Makefile
to generate built-in.o on the real Kbuild.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This patch add new defines for usb phy for Exynos4x12.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
add the possibility to set the bcdDevice number board specific.
Therefore the weak function g_dnl_get_board_bcd_device_number()
is introduced. Used on the siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
add the possibility to set the iSerialNumber board specific.
Default value for iSerialNumber is 0x0. This value can
changed board specific through the new function
g_dnl_set_serialnumber() which must be called from the
board specific function g_dnl_bind_fixup().
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
This patch allows exiting from UMS mode to u-boot prompt
by detaching usb cable or by pressing ctrl+c.
Add new config: CONFIG_USB_CABLE_CHECK. If defined then board
file should provide function: usb_cable_connected() (include/usb.h)
that return 1 if cable is connected and 0 otherwise.
Changes v2:
- add a note to the README
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
This patch prevents:
- ums disk capacity miscalculation because of integer overflow
Changes v2:
- Prevents passing zero size disk capacity to ums gadget driver
- Change function ums_get_capacity() to ums_disk_init() and do ums disk
initialization before gadget init
- Remove unnecessary code from mass storage driver
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
This patch introduces some cleanups to ums code. Changes:
ums common:
- introduce UMS_START_SECTOR and UMS_NUM_SECTORS as defined in
usb_mass_storage.h both default values as 0 if board config
doesn't define them
common cleanup changes:
- change name of struct "ums_board_info" to "ums"
- "ums_device" fields are moved to struct ums and "dev_num" is removed
- change function name: board_ums_init to ums_init
- remove "extern" prefixes from usb_mass_storage.h
cmd_usb_mass_storage:
- change error() to printf() if need to print info message
- change return values to command_ret_t type at ums command code
- add command usage string
Changes v2:
ums common:
- always returns number of read/write sectors
- coding style clean-up
ums gadget:
- calculate amount of read/write from device returned value.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Move defines only needed by mv_udc.c to a file
in the same directory.
This allows usbtty to compile for mv_udc,
but it still doesn't link.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Only perform one copy, either in the bounce
routine for IN transfers, or the debounce
rtn for OUT transfer.
On out transfers, only copy the number
of bytes received from the bounce buffer
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
i.mx6 has 1 otg controller, and 3 host ports. So,
CONFIG_USB_MAX_CONTROLLER_COUNT can be greater than 1
even though only 1 device mode controller is supported.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Implementation of USB download function which supports THOR protocol.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
New parameter, namely *name has been added to g_dnl_bind_fixup().
It is necessary (for compatibility reasons) to assign new USB idProduct
and idVendor for different usb functions.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
When the usb_configuration structure is declared as static, it is very
hard to assure, that relevant fields (as e.g. config->interfaces[]) are
cleared out before new call to g_dnl related functions.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
The s3c udc driver sends data in a max packet size. Therefore the dcache
invalidate range shall be equal to max packet, not the entire
DMA_BUFFER_SIZE.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Make sure the transfer descriptor is flushed
before the queue is updated so that the controller
will not see old information.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
This prevents a crash if tftpboot is given a bad filename.
rx_req will be released by eth_reset_config
which is called by eth_disconnect,
which is called using the .disconnect member of usb_gadget_driver by mv_pullup in mv_udc
which is called using the .pullup member of usb_gadget_ops by usb_gadget_disconnect
which is called by usb_eth_halt
which is called using the .halt member of eth_device by eth_halt
which is called by TftpHandler when TFTP_ERR_FILE_NOT_FOUND or TFTP_ERR_ACCESS_DENIED occurs
I trigger this with the following commands
setenv ipaddr 10.0.0.2 && setenv netmask 255.255.255.0 && setenv serverip 10.0.0.1
setenv usbnet_devaddr 00:11:22:33:44:55 && setenv usbnet_hostaddr 00:aa:bb:cc:dd:ee
setenv ethprime usb_ether && setenv ethact usb_ether && setenv ncip 10.0.0.1
tftpboot 10800000 10.0.0.1:missing_file
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
set wMaxPacketSize for full speed descriptors
fs_source_desc, fs_sink_desc to 64.
Full-speed bulk endpoint can have a maximum packet size of
8, 16, 32, or 64 bytes, so choice 64.
The hs_source_desc, hs_sink_desc, already have their wMaxPacketSize
set to 512. That is the only legal value for high speed bulk endpoints.
Strictly speaking, this patch is not needed because
usb_ep_autoconfig will call ep_matches which will
override wMaxPacketSize for BULK endpoints only with
the size associated with the endpoint setup by the udc driver.
But if you want to rely on this, you may as well combine the
full speed descriptor with the high speed descriptor to
minimize confusion.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
The download gadget code and DFU function lacks of proper declarations
for the case when a target board wants to use only one of available usb
functions.
Moreover the relevant declarations have been moved to consistent
localization (like <dfu.h>).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Only the <linux/usb/gadget.h> requires error.h include. Hence, several
includes of error.h at USB gadget functions are not needed.
Moreover unnecessary malloc.h includes were also removed.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
The mass storage composite function is now compiled in only when
CONFIG_USB_GADGET_MASS_STORAGE is defined.
Such change provides binary size reduction for boards which use USB
download gadget (like am335x_evm) with DFU, but don't use UMS.
For example at am335x_evm board reduction is more than 2KiB for
text and around 120B for data.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Add atmel usba udc driver support, porting from Linux kernel
The original code in Linux Kernel information is as following
commit e01ee9f509a927158f670408b41127d4166db1c7
Author: Jingoo Han <jg1.han@samsung.com>
Date: Tue Jul 30 17:00:51 2013 +0900
usb: gadget: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
As seen with codesourcery compiler 2010q1, the buf pointer in
usb_request structure is not aligned on 4 bytes boundary causing
data aborts in eth_setup -> conf_buf -> usb_gadget_config_buf.
Make it as align access to fix this issue.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
[voice.shen@atmel.com: add commit message]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
As seen on GCC 4.6 Linaro compiler, control_req buffer is not aligned
on 4 byte boundaray causing data aborts in eth_setup -> conf_buf
during dhcp boot over usb_ether. Fix the issue my aligning control_req
buffer using DEFINE_CACHE_ALIGN_BUFFER.
Tested on am335x_evm platform (beaglebone).
Applies on 2013.10-rc1 branch.
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Joel Fernandes <joelf@ti.com>
The manufacturer and product IDs are dynamically assigned when gadget is
bind.
Now the IDs aren't assigned at struct g_dnl_string_defs definition.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Egli, Samuel" <samuel.egli@siemens.com>
USB composite gadget (g_dnl) supports only one configuration. Due to that
the corresponding field - bConfigurationValue has been changed.
Moreover more descriptive names were chosen for relevant fields.
Windows XP setup:
- Thesyscon USB Descriptor Dumper
- zadig_xp program for WinUSB installation (which is required by dfu-util)
- dfu-util for windows (version 0.6)
- TRATS target connected via USB hub to test Win XP machine.
Tested at: Trats - Exynos4210
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Egli, Samuel" <samuel.egli@siemens.com>
This patch extends dfu code to support transmission with -R switch
specified at dfu-util.
When -R is specified, the extra USB_REQ_DFU_DETACH request is sent after
successful data transmission. Then dfu resources are released and reset
command is issued.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The requests sent to the controller are not properly cache aligned
most of the time, thus implement a simple bounce buffer to avoid
problem with cache.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Implement functions to flush/invalidate dcache over QH and qTDs
and make use of them where appropriate. Also use them to replace
the old incorrect cache management attempt. This is the first step
towards making this driver work with data cache enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The code for retrieving qTD item for particular endpoint is hard
to understand, moreover it's duplicated all over the driver. Move
the code into single nice and documented function.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Allocate the qTD items all at once instead of allocating them
separately. Moreover, make sure each qTD is properly aligned
to 32-bytes boundary and that cache can be safely flushed over
each qTD touple.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The code for retrieving QH for particular endpoint is hard to understand,
moreover it's duplicated all over the driver. Move the code into single
nice and documented function.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Check the length of system cacheline at compile-time and fail
if the system uses too long cachelines.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The endpoint QH list has to be aligned to 10-bit boundary. We also have
to make sure the list is aligned on a cacheline boundary. Make sure it
is. Furthermore, check if the memory allocation for the QH list didn't
fail. Moveover, improve the comment about the QH list structure.
Finally, the qTD item list has to be aligned only to 5-bit boundary, not
10-bit as it is now, fix this as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Both the endpoint queue head and the endpoint item list is a controller
specific thing. Move them both into controller private data.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
There is no need to init this field at runtime, so init it statically.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The QH_MAXNUM is used in absolutelly incorrect manner and is not
even needed. Remove it and correctly replace it's occurance with
2 * NUM_ENDPOINTS .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Clean up the code that checks the validity of a USB gadget driver
in usb_gadget_register_driver(). Moreover, limit the speed of the
driver to either FULL or HIGH, this is more precise and once we
have xHCI support, also more correct.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The usb_lowlevel_init() call already fills and passes back struct
ehci_ctrl , which readily contains correctly determined address of
the port register block address computed from values from controller
configuration registers. Leverage this and make use of this value
as this makes the code mode universal, but also gets us rid of the
CONFIG_USB_REG_BASE configuration option.
Moreover, this patch cleans up the usb_gadget_register_driver() call
a little by correcting the error handling. Note the usb_lowlevel_init()
and mvudc_probe() are now called in reversed order, but this has no
impact on the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Move the constant values that are programmed into mv_ep.ep into
separate static const structure so they can be memcpy()'d when
the initialization happens.
Moveover, we only every init NUM_ENDPOINTS, not 2 * NUM_ENDPOINTS,
so fix this bug as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The endpoints are operated on a per-controller basis, move the
endpoint array into controller's private data. Also shuffle the
struct mv_ep structure definition just above the definition of
the struct mv_drv so they're well grouped together.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The mv_udc driver is broken for a while and doesn't even compile.
This patch fixes the issues and gets the driver into working state
again. This driver was tested on Freescale i.MX233/i.MX28 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Newer gcc versions warn about unused variables. This patch corrects a few of
those warnings that popped up in a build for the palmtreo680 board.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
The DFU's state machine original implementation author and copyright were
missing.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
