Radxa dalang carrier board has 2x USB 2.0 and 1x USB 3.0
ports.
This patch adds support to enable all these USB ports for
N10 and N8 combinations SBCs.
Note that the USB 3.0 port on RockPI N8 combination works
as USB 2.0 OTG since it is driven from RK3288.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rk3288 and rk3288w have a usb host0 ohci controller.
Although rk3288 ohci doesn't actually work on hardware, but
rk3288w ohci can work well.
So add usb host0 ohci node in rk3288 dtsi and the quirk in
ohci platform driver will disable ohci on rk3288.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This sync has changes required to use HDMI CEC pin in U-Boot.
Sync dts from linux v5.8-rc5 commit:
"ARM: dts: rockchip: define the two possible rk3288 CEC pins"
(sha1: 838980dd04e994bf81cf104fa01ae60802146b39)
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
reset cause is a generic functionality based on the soc
cru registers in rockchip. This can be used for printing
the cause of reset in cpuinfo or some other place where
reset cause is needed.
Other than cpuinfo, reset cause can also be using during
bootcount for checking the specific reset cause and glow
the led based on the reset cause.
So, let's separate the reset cause code from cpuinfo, and
add a check to build it for rk3399, rk3288 since these two
soc are supporting reset cause as of now.
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
reset reason can be used several stages of U-Boot bootloader
like SPL, U-Boot proper based on the requirements.
Clearing the status register end of get_reset_cause will end
up showing the wrong reset cause when it read the second time.
For example, if board resets, SPL reads the reset status as
RST whereas U-Boot proper reads the status as POR.
However, based on the latest testing clearing reset status
won't be required for determine the last reset cause or
following resets.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add weak led_setup() so that board which has an uncommon
led setup code that can make use of custom implementation.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The new rk3288 revision rk3288w has some changes with respect
to legacy rk3288 like hclk_vio in cru and usb host0 ohci.
Linux clock driver already handle this via rockchip,rk3288w-cru
compatible.
USB ohci host can enable via dts for rk3288w based boards.
So, add fdt board setup code to update cru compatible with
rk3288w-cru compatible if the SOC revision is RK3288W.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip SoC's has a new revision chip for rk3288 SoCs.
RK3288 has a new revision chip called RK3288W which is similar
but different hclk_vio clock and fixed OHCI host.
Add common Rockchip SoC detection helper to support this rk3288w
detection.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enabled
GPIO pin change compared to 4B, 4C.
So, add or enable difference nodes/properties in 4C dts
by including common dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock PI 4 has 3 variants of hardware platforms called
RockPI 4A, 4B, and 4C.
- Rock PI 4A has no Wif/BT.
- Rock PI 4B has AP6256 Wifi/BT, PoE.
- Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enable
GPIO pin change compared to 4B, 4C
So move common nodes, properties into dtsi file and include
on respective variant dts files.
Use 4B dts into default rock-pi-4 defconfig until we find any
solution for dynamic detection of these variants.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently 2.5 GB is calculated as DRAM size for a 1 GB RK322x board
if CONFIG_SPL_OPTEE is set. This is troublesome when booting a
linux kernel since this size will be injected in FDT of the kernel.
gd->bd->bi_dram[0].start (which is basically CONFIG_SYS_SDRAM_BASE)
must not be taken into consideration for calculation of second bank
size, since this offset is already included in calculation of "top".
After applying this patch 992 MB (1024 MB - 32 MB reserved for
optee-os) is correctly calculated and has also been verified on
2 GB boards.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The empty function define should not be in the header file, or else the
build will error with function multi definition after CONFIG_RAM_ROCKCHIP_DEBUG
is disabled.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI Flash support for the PINE64 Rock64 board
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI support for the RK3328
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(fix checkpatch error for code ident)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Also known as Odroid Go Advance but named Go2 internally by the
vendor it seems.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Get the devicetree from mainline Linux and include it for U-Boot uses.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3326 is just a trimmed down px30 from a software perspective,
so the mainline rk3326 dtsi also ist just a tiny addition.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some code was not converted by coccinelle, somehow.
I manually fixed up the remaining, and comments, README docs.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
[trini: Add arch/arm/mach-davinci/include/mach/sdmmc_defs.h and
include/fdt_support.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXxCxWw8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76bPyACcDZ8gD9jf1P/Zh+7kqrGdIWwURF8AnAiEtNnu
FhE/WQQj4mAEWE4F2bFE
=7ceG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200716' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
i.MX for 2020.10
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
OF graph endpoint connections must be bidirectional and dtc warn if they
are not. i.MX7 based DTs have an error and generate
warnings:
arch/arm/dts/imx7d-sdb.dtb: Warning (graph_endpoint):
/replicator/ports/port@0/endpoint: graph connection to node
'/soc/tpiu@30087000/port/endpoint' is not bidirectional
arch/arm/dts/imx7d-sdb.dtb: Warning (graph_endpoint):
/soc/tpiu@30087000/port/endpoint: graph connection to node
'/replicator/ports/port@1/endpoint' is not bidirectional
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Even if the HAB fuse is not set we want to be able to use the Cryptographic
Accelerator and Assurance Module (CAAM) for generating random numbers. So
SYS_FSL_HAS_SEC should be selected even if IMX_HAB is not set.
arch_misc_init() has to be called to initialize the CAAM.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add SCFW API sc_misc_get_boot_container to get current boot container
set index.
The index value returns 1 for primary container set, 2 for secondary
container set.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Convert pcm058 support to use device trees and the driver model.
Add rudimentary boot scripts to the environment, expand README.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add Phytec Mira device tree files, for use with pcm058.
>From Linux 5.6, commit 7111951b8d49 upstream
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Current codes assume the OPTEE address is at the end of first DRAM bank.
Adjust the process to allow OPTEE in the middle of first bank.
When OPTEE memory is removed from first bank, it may split the first bank
to two banks, adjust the MMU table for the split case,
Since the default CONFIG_NR_DRAM_BANKS is 4, it is enough, just enlarge
i.MX8MP evk to default to avoid issue.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Silvano di Ninno <silvano.dininno@nxp.com>
Tested-by: Silvano di Ninno <silvano.dininno@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To fused part, we need to disable nodes of dtb to let kernel boot.
To mfgtool, USB issue when using super-speed for mfgtool, temporally
work around the problem to use high-speed only.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To use one defconfig for all boot device, we have to runtime set
env offset and return env medium according to the boot device.
This patch overrides the env_get_offset and env_get_location to
implement the feature.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
iMX8MP has 6 fused parts in each qualification tier, with core, VPU,
ISP, NPU or DSP fused respectively.
The configuration tables for enabled modules:
MIMX8ML8DVNLZAA Quad Core, VPU, NPU, ISP, DSP
MIMX8ML7DVNLZAA Quad Core, NPU, ISP
MIMX8ML6DVNLZAA Quad Core, VPU, ISP
MIMX8ML5DVNLZAA Quad Core, VPU
MIMX8ML4DVNLZAA Quad Lite
MIMX8ML3DVNLZAA Dual Core, VPU, NPU, ISP, DSP
Add the support in U-Boot
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
ROM SError happens on two cases:
1. ERR050342, on iMX8MQ HDCP enabled parts ROM writes to GPV1 register, but
when ROM patch lock is fused, this write will cause SError.
2. ERR050350, on iMX8MQ/MM/MN, when the field return fuse is burned, HAB
is field return mode, but the last 4K of ROM is still protected and cause
SError.
Since ROM mask SError until ATF unmask it, so then ATF always meets the
exception. This patch works around the issue in SPL by enabling SPL
Exception vectors table and the SError exception, take the exception
to eret immediately to clear the SError.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add imx_eqos_txclk_set_rate/imx_get_eqos_csr_clk to override the
weak function in driver
Add set_clk_eqos to configure eQoS clk
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Current DM CLK is a bit complicated, for simplity, let DM clk only
support enable/disable/get_rate. For the expected rate settings,
we use non-DM clk to do that. Then we could have simple DM clk for
i.MX and could also share between SPL/U-Boot proper.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
A53 CCM root max support 1GHz, to support high freq, we need
to switch ARM clk sources from ARM PLL directly.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add logic to automatically update umctl2's setting based
on phy training CDD value for rank to rank space issue
Acked-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Oliver Chen <Oliver.Chen@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
the DRAM Controller in i.MX8MP will support a feature called "Inline ECC".
This is supported for all 3 supported DRAM technologies (LPDDR4, DDR4 and
DDR3L). When this feature is enabled by software, the DRAM Controller
reserves 12.5% of DRAM capacity for ECC information, and presents only
the non-ECC portion (lower 87.5% of the installed capacity of DRAM) to
the rest of the SoC.
The DRAM memory can be divided into 8 regions so that if a use case only
requires ECC protection on a subset of memory, then only that subset of
memory need support inline ECC. If this occurs, then there is no
performance penalty accessing the non-ECC-protected memory (no need to
access ECC for this portion of the memory map). This is all configured
with the DRAM Controller.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Replace the function spl_board_prepare_for_boot_linux by the correct
name of the weak function spl_board_prepare_for_linux defined in spl.h.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Buiding u-boot-spl-k3[_HS].its is currently unconditionally verbose
about what it does. Change that by wrapping the call to k3_fit_atf.sh
into a cmd, also using that chance to reduce duplicate lines of makefile
code - only IS_HS=1 is different when CONFIG_TI_SECURE_DEVICE is on.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Sync DT bindings from kernel DT and move them to out of -u-boot.dtsi
files.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Now that commit 3e57f879ee ("mtd: nand: raw: denali: Assert reset
before deassert") added the reset assertion, this code in the board
file is unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now that this directory contains only uniphier_sbc_boot_is_swapped(),
move it to boot-device.c and delete the sbc/ directory entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit 1517126fda ("ARM: uniphier: select DM_ETH"), DM-based
drivers/net/smc911x.c is compiled, but it is never probed because the
parent node lacks the DM-based driver.
I need a skeleton driver to populate child devices (but the next commit
will move more hardware settings to the this driver).
I put this to drivers/bus/uniphier-system-bus.c because this is the
same path as the driver in Linux kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I actually do not see this used these days because eMMC or NAND is used
for non-volatile devices. Dump the burden to maintain this crappy code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This was used by the old sLD3 SoC, the support of which was removed
by commit 00aa453ebf ("ARM: uniphier: remove sLD3 SoC support").
There is no more user of this function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, the supports for the following two ARMv7 SoC groups
are exclusive, because the boot ROM loads the SPL to a different
address:
- LD4, sLD8 (SPL is loaded at 0x00040000)
- Pro4, Pro5, PXs2, LD6b (SPL is loaded at 0x00100000)
This limitation exists only when CONFIG_SPL=y.
Instead of using crappy CONFIG options, checking SPL and SPL_TEXT_BASE
is cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit 45f41c134b.
This weird workaround was the best I came up with at that time
to boot U-Boot from TF-A.
I noticed U-Boot successfully boots on LD20 (i.e. CA72 CPU) by using
the latest TF-A.
Specifically, since the following TF-A commit, U-Boot runs at EL2
instead of EL1, and this issue went away as a side-effect.
|commit f998a052fd94ea082833109f25b94ed5bfa24e8b
|Author: Masahiro Yamada <yamada.masahiro@socionext.com>
|Date: Thu Jul 25 10:57:38 2019 +0900
|
| uniphier: run BL33 at EL2
|
| All the SoCs in 64-bit UniPhier SoC family support EL2.
|
| Just hard-code MODE_EL2 instead of using el_implemented() helper.
|
| Change-Id: I7ab48002c5205bc8c013e1b46313b57d6c431db0
| Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
However, if I reverted that, this problem would come back, presumably
because some EL1 code in U-Boot triggers this issue.
Now that commit f8ddd8cbb5 ("arm64: issue ISB after updating system
registers") fixed this issue properly, this weird workaround is no
longer needed irrespective of the exception level at which U-Boot runs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
patman support for Python3 on Ubuntu 14.04
new checkpatch check to avoid #ifdefs
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8InaQRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreazvAgAgqyvPY2o+BNHscrx9/6sEOHSAVty/D5t
SdaphzRezlJOWy9MC/ZyqyevZjogN7fgGNQVgh/I4BklIc/N5Omn68/+JWylSFVP
taJKiJD1IVSThTXGOMTxlDiTxY7NfVDUDjtFIpCDswBrnSJlX+2v/RsehUwVIrYn
NJwiRXd33IdS1vh1mqqNgwbZNBo+zGWn5LApq71vLSVkiQlmcpMG9FmYYRcg/AhG
3Xd2HB2ANcvb13fMMcwd3s4WPNYoiJvwjSHScNDUPEip7XeZNDiNeq4gC6d2Uw+J
zC3/vOCP3eRtAnr6syJ5QcGN/eeKwLtnTE+fOuOm6s5Y98po4iMykA==
=3fC5
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10jul20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
of-platdata: better phandle and compatible-string support
patman support for Python3 on Ubuntu 14.04
new checkpatch check to avoid #ifdefs
Create a non-cacheable mapping for the 0x600000000 physical memory region,
where MMIO registers for the PCIe XHCI controller are instantiated by the
PCIe bridge. Due to 32bit limit in the CPU virtual address space in ARM
32bit mode, this region is mapped at 0xff800000 CPU virtual address.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Provide function for setting arbitrary virtual-physical MMU mapping
and cache settings for the given region.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the comments in include/asm/system.h to the common style.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On the Raspberry Pi 4, after a PCI reset, VL805's (a xHCI chip) firmware
may either be loaded directly from an EEPROM or, if not present, by the
SoC's VideCore (the SoC's co-processor). Introduce the function that
informs VideCore that VL805 may need its firmware loaded.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Several MMC drivers use GPIO for card detection with cd-gpios property in
the MMC node pointing to a GPIO node. However, as U-Boot tries to save
space by keeping only required nodes using u-boot* properties, several
devices tree result in having only in the MMC node but not the GPIO node
associated to cd-gpios.
This patch, fixes several ocurrence of this issue.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
When using OF_PLATDATA, the bind process between devices and drivers
is performed trying to match compatible string with driver names.
However driver names are not strictly defined, and also there are different
names used when declaring a driver with U_BOOT_DRIVER, the name of the
symbol used in the linker list and the used in the struct driver_info.
In order to make things a bit more clear, rename the drivers names. This
will also help for further OF_PLATDATA improvements, such as checking
for valid driver names.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a fix for sandbox of-platdata to avoid using an invalid ANSI colour:
Signed-off-by: Simon Glass <sjg@chromium.org>
DM, OF_CONTROL, DM_SPI and other driver model migration
deadlines are expired for this board.
Remove it.
Acked-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Gilles Gameiro <gilles@gigadevices.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Drop it.
Cc: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Drop it.
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Drop it.
Cc: Ash Charles <ash@gumstix.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
DM, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
DM, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- Add two- and three-argument versions of CONFIG_IS_ENABLED in
linux/kconfig.h
- Adds a new feature which supports copying modified parts of
the frame buffer to the uncached hardware buffer
- Enable the copy framebuffer on various x86 targets
Create a non-cacheable mapping for the 0x600000000 physical memory region,
where MMIO registers for the PCIe XHCI controller are instantiated by the
PCIe bridge.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Remove the overlap between DRAM and device's IO area.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The spi0 alias is needed by the environment code to retrieve the SPI
flash. This patch adds some -u-boot.dtsi files, providing the spi0
aliases, for all the following Kirkwood-based LaCie boards:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2
Note that this -u-boot.dtsi files will be removed as soon as the spi0
aliases will be available in the upstream Linux dtsi files.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The helios4 is built on the same microsom as the clearfog, by syncing the config
we enable the same featureset that exists in the som on the helios4. The current
config does not boot as some of the clearfog changes needed to be made on the
helios4 also, generally speaking most changes for the clearfog should also be
made on the helios4.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Reviewed-by: Stefan Roese <sr@denx.de>
When running USB compliance tests on our Armada-385 hardware platforms
we have seen some eye mask violations. Marvell's internal documentation
says: Based on silicon test results, it is recommended to change the
impedance calibration threshold setting to 0x6 prior to calibration.
Port changes from Marvell's u-boot fork[1] to address this.
[1] - https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/a6221551
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add parentheses around CONFIG_IS_ENABLED() in the if statement, to
fix potential build failures.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The PHY needs a reset in order to be functionnal for U-Boot, add the old
PHY reset bindings for dwmac until we support the new bindings in the PHY node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Odroid C4 is an Amlogic SM1 device, the board config and board documentation
are adapted from the Odroid-N2 support from the same vendor.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: fix odroid-c4.rst typos and structure]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
This imports the changes and the new Odroid-C4 board from the Linux
commit b3a9e3b9622a ("Linux 5.8-rc1").
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
The smc911X driver is now DM enabled, so we can switch the Juno board
over to use DM_ETH for the on-board Fast Ethernet device.
Works out of the box by using the DT.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Compiling with clang on ARMv8 shows errors like:
./arch/arm/include/asm/system.h:162:32: note: use constraint modifier "w"
asm volatile("msr sctlr_el1, %0" : : "r" (val) : "cc");
^~
%w0
These errors are due to using an incorrect size for the variables used
for writing to and reading from special registers which have 64 bits on
ARMv8.
Mask off reserved bits when reading the exception level.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This patch selects CONFIG_DM_ETH (ethernet driver is base on DM model)
for Action semi owl SoC.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch adds node for ethernet controller found on Action Semi OWL
S700 SoC.
Since, there is no upstream Linux binding exist for S700 ethernet
controller, Changes are put in u-boot specific dtsi file.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patchs adds glue logic to enable designware mac present on
Action Semi based S700 SoC, Configures SoC specific bits.
Undocumented bit that programs the PHY interface select register
comes from vendor source.
It has been tested on Cubieboard7-lite based on S700 SoC.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This commit adds clocks needed for ethernet operations for
Actions OWL family of SoCs (S700 and S900).
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Calculate the SDRAM size from DDR capacity register registers instead
of using hard-coded value. This is quite useful to get correct size
on differnt boards based on Actions OWL family of SoCs (S700 and S900).
There is no documentation available that talks about DDR registers, and
this is very much taken from vendor source.
This commit lets Linux boot on Cubieboard7-lite(based on S700).
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
- use OPP information in device tree for 800MHz/650MHz support
- ram: inprovments of test command
- solve boot on closed chip when access to DBGMCU_IDC is protected
- stm32prog command: Add "device anme" during USB enumeration
- update configs: activate WATCHDOG and 'env erase' command,
increase teed partition, support SD card after NOR boot by default and
use env info in env_check
- some sboard cleanups: gpio hog in dh board, specific driver for
type-c stusb1600 controller code in a driver move part of code in spl.c
and in common directory
- fix STM32 compatible for dwc_eth_qos driver
- support of new pinctrl ops get_dir_flags/set_dir_flags in stm32 and stmfx
drivers
- vrefbuf: fix a possible overshoot when re-enabling
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl8EgGEACgkQ4rK92eCq
k3V7mwf+N5Iq6CbUPP11mFiNgAFZ5+hcn6gBTWvbjnd+oaIp15hiQrUNusGNFxXe
oyM4fvm12tjuWFlA0U6VtiLhuVQB1Yte048oX+edDCCLGwxkp6cKBHtCaGT14XvY
ow60XInv/dlrINumf8isy+5QlLgT1Cb7aGZN1qRHsUtnHB/IC836KO+hukGRUvk3
Lqz+FbHqitKnL+CIboC2+YzXqG6ZXdixFZVVPmTVd34C8hQOdkExJ//uR/lH/s6f
vjaecs7HpIuKRpKpt5WcoLzTLd1hstqNNhmTbBHmVo+EqIjMkpISUwDpDJNU5pki
BPbdG9VXqb46JLaTtPT+U4gX4yJ3Bw==
=jQCC
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200707' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- arch and board update for stm32mp15:
- use OPP information in device tree for 800MHz/650MHz support
- ram: inprovments of test command
- solve boot on closed chip when access to DBGMCU_IDC is protected
- stm32prog command: Add "device anme" during USB enumeration
- update configs: activate WATCHDOG and 'env erase' command,
increase teed partition, support SD card after NOR boot by default and
use env info in env_check
- some sboard cleanups: gpio hog in dh board, specific driver for
type-c stusb1600 controller code in a driver move part of code in spl.c
and in common directory
- fix STM32 compatible for dwc_eth_qos driver
- support of new pinctrl ops get_dir_flags/set_dir_flags in stm32 and stmfx
drivers
- vrefbuf: fix a possible overshoot when re-enabling
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl8DHgAcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyAdDCACFX01IPRmdkNEYrJf0
YfhQPAPZ/5EyHBv36ePl93CbIRnJPpnrGbBXe8+/Jdcq7l6EkJh2cuO+t9axXner
m0kH35LzLiR9Olz6q5Su0InPWpnDtXxtIczK5v7ZHBeMZ2so763e7SQ2VIMyJJb/
VT6hilqJK6+W1c2X1wmzxyh/nnv/bDBz97cavJN1EKw1arYr8jh/8/tpABk5msDm
J6Z5WsS/CYk7cj6hX7dSNRfqcKsjl/gCYjnVssfgaP1sH+NX0mtS8C6zchNILmpB
2T/dKnpYBBAWTD5fGNVKxKphAuZgQHw51AJhkOnYDrMKisifFC0ssvxkh+nvwyTm
1w4R
=1YzJ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.10-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2020.10 cycle
ARM Architecture reference manual clearly states that PE pipeline
should be flushed after changes to some system registers. Refer to
paragraph "B2.3.5 Memory Barriers" at page B2-92 of "Arm Architecture
Reference Manual ARMv8 for ARMv8-A Architecture Profile" (ARM DDI
0487B.a).
Failing to issue instruction synchronization barrier can lead to
spurious errors, like synchronous exception when accessing FPU
registers. This is very prominent on CPUs with long instruction
pipeline, like ARM Cortex A72.
This change fixes the following U-Boot panic:
"Synchronous Abort" handler, esr 0x1fe00000
elr: 00000000800948cc lr : 0000000080091e04
x0 : 00000000801ffdc8 x1 : 00000000000000c8
x2 : 00000000800979d4 x3 : 00000000801ffc60
x4 : 00000000801ffd40 x5 : ffffff80ffffffd8
x6 : 00000000801ffd70 x7 : 00000000801ffd70
x8 : 000000000000000a x9 : 0000000000000000
x10: 0000000000000044 x11: 0000000000000000
x12: 0000000000000000 x13: 0000000000000000
x14: 0000000000000000 x15: 0000000000000000
x16: 000000008008b2e0 x17: 0000000000000000
x18: 00000000801ffec0 x19: 00000000800957b0
x20: 00000000000000c8 x21: 00000000801ffdc8
x22: 000000008009909e x23: 0000000000000000
x24: 0000000000000000 x25: 0000000000000000
x26: 0000000000000000 x27: 0000000000000000
x28: 0000000000000000 x29: 00000000801ffc50
Code: a94417e4 a90217e4 a9051fe6 a90617e4 (3d801fe0)
While executing instruction
str q0, [sp, #112]
in vsnprintf() prologue. This panic was observed only on Cortex A72 so
far.
This patch places ISBs on other strategic places as well.
Also, this probably is the right fix for the issue workarounded in the
commit 45f41c134b ("ARM: uniphier: add weird workaround code for LD20")
Reported-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Suggested-by: Julien Grall <julien.grall.oss@gmail.com>
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
CC: Tom Rini <trini@konsulko.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stefano Stabellini <sstabellini@kernel.org>
Reviewed-by: Julien Grall <julien@xen.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Activate CMD_NVEDIT_INFO and use the new command "env info -d -p -q"
to automatically save the environment on first boot.
This patch allows to remove the env_default variable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
As debugger must be totally closed on Sec closed chip,
the DBGMCU_IDC register is no more accessible (self
hosted debug is disabled with OTP).
This patch adds a function bsec_dbgswenable() to check
if the DBGMCU registers are available before to access them:
BSEC_DENABLE.DBGSWENABLE = self hosted debug status.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add "Device Name" in iproduct during DFU USB enumeration
to have this information in STM32CubeProgrammer trace
(this tools is compatible with @Name since v2.3)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch allows to switch the CPU frequency to 800MHz on the
ST Microelectronics board (DK1/DK2 and EV1) or dh electronics SOM
using the STM32MP15x SOC and when it is supported by the HW
(for STM32MP15xD and STM32MP15xF).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a function stmpic_init to early initialize the PMIC STPMIC1
- keep vdd on during the reset cycle (to avoid issue when backup battery
is absent)
- Check if debug is enabled to program PMIC according to the bit
This patch allows to remove the compilation of spl.c file from stm32mp1
board in dh_stm32mp1.
CONFIG_SPL_BOARD_INIT is removed as the new function is called earlier
in SPL, in the function board_early_init_f.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a weak functions to save the vddcore voltage value provided
in the OPP node when the clock tree is initialized.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This commit adds cpufreq support on stm32mp15x SOC. STM32 cpufreq uses
operating points V2 bindings (no legacy). Nvmem cells have to be used to
know the chip version and then which OPPs are available. Note that STM32
cpufreq driver is mainly based on "cpufreq-dt" driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add the bsec driver in SPL, as it is needed by SOC part number detection
to found the supported OPP.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Rock Pi N8 is a Rockchip RK3288 based SBC, which has
- VMARC RK3288 SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.
VAMRC RK3288 SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N8 SBC.
So, add initial support for Rock Pi N8 by including rk3288,
rk3288 vamrc-som and raxda dalang carrier board dtsi files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
VMARC RK3288 SOM is a standard SMARC SOM design with
Rockchip RK3288 SoC, which is designed by Vamrs.
Specification:
- Rockchip RK3288
- PMIC: RK808
- SD slot, 16GiB eMMC
- 2xUSB-2.0, 1xUSB3.0
- USB-C for power supply
- Ethernet, PCIe
- HDMI, MIPI-DSI/CSI, eDP
Add initial support for VMARC RK3288 SOM, this would use
with associated carrier board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa dalang carrier boards are used to mount vmarc SoM's
of rk3399pro and rk3288 to make complete SBC.
Among these combinations, card detection gpio, max-frequency
properties are used with rk3399pro SoM but not required for
rk3288 SoM based on the hardware schematics.
So, let's move these sdmmc specific properties on associate
vmarc dtsi to make common use of dalang carrier device tree file.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
SPL_ATF_NO_PLATFORM_PARAM is selected by default for RK3399 configs, to
guard against issues when used with TF-A versions that perform
insufficient validation on the platform parameter. However, since commit
8109f738ffa7 "rockchip: increase FDT buffer size" in TF-A, passing a
device tree as platform parameter no longer causes problems for upstream
TF-A for RK3399.
Since SPL_ATF_NO_PLATFORM_PARAM doesn't need to be selected when using
upstream TF-A, change the Kconfig option from select to imply. It'll
still default to being selected but can be deselected by a user if they
know they will be using a compatible version of TF-A.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Walter Lozano <walter.lozano@collabora.com>
Rock Pi N10 is a Rockchip RK3399Pro based SBC, which has
- VMARC RK3399Pro SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.
VAMRC RK3399Pro SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N10 SBC.
So, add initial support for Rock Pi N10 by including rk3399,
rk3399pro vamrc-som and raxda dalang carrier board dtsi files.
rk3399pro-rock-pi-n10.dts was synced from linux-next v5.7-rc1.
Tested
- ROCK PI N10 Model B
- ROCK PI N10 Model C
- Boot from SD
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Carrier board often referred as baseboard. For making
complete SBC or any other industrial boards, these
carrier boards will be used with associated SOMs.
Radxa has Dalang carrier board which supports on-board
peripherals, ports like USB-2.0, USB-3.0, HDMI, MIPI DSI/CSI,
eDP, Ethernet, WiFi, PCIe, USB-C, 40-Pin GPIO header and etc.
Right now Dalang carrier board is used with two SBC-variants:
Rock Pi N10 => VMARC RK3399Por SOM + Dalang carrier board
Rock Pi N8 => VMARC RK3288 SOM + Dalang carrier board(+codec)
So add this carrier board dtsi as a separate file in
ARM directory, so-that the same can reuse it in both
rk3288, rk3399pro variants of Rockchip SOMs.
Sync this dtsi from linux-next v5.7-rc1.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
VMARC RK3399Pro SOM is a standard SMARC SOM design with
Rockchip RK3399Pro SoC, which is designed by Vamrs.
Specification:
- Rockchip RK3399Pro
- PMIC: RK809-3
- SD slot, 16GiB eMMC
- 2xUSB-2.0, 1xUSB3.0
- USB-C for power supply
- Ethernet, PCIe
- HDMI, MIPI-DSI/CSI, eDP
Add initial support for VMARC RK3399Pro SOM, this would use
with associated carrier board.
Sync this dtsi from linux-next v5.7-rc1.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some minor fixes for SPI flash on the Pinebook Pro and also
default to saving environment to the SPI flash as it's
guaranteed to be on board.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(applied with make savedefconfig)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Enable the rng so UEFI can provide entropy for KASLR
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Unless we mark the function as 'static inline' it may end up being
non-inlined by the compiled and result in duplicate functions.
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Vasut <marex@denx.de>
In order to update our <linux/compiler.h> to a newer version that no
longer provides ACCESS_ONCE() but only READ_ONCE()/WRITE_ONCE() we need
to convert arch/arm/mach-tegra/ivc.c to the other macros.
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Minor updates to some platforms I am the listed maintainer of.
Notably this removes the ti814x_evm which stopped building with the PXA
MMC migration series (oops) but hasn't been functional in some time.
The TI814x (DM814x) platform is rather old and in need of a lot of
migration work. As much of that work is well past the deadline, remove
this platform.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
-----BEGIN PGP SIGNATURE-----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=dnTK
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-06-29' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips into next
- net: pcnet: cleanup and add DM support
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
This patch moves the CONFIG_DM_SPI_FLASH and CONFIG_SPI_FLASH_DATAFLASH
to be defined in Kconfig, not in board specific header file
(include/configs/<board>.h).
Before this change the CONFIG_DM_SPI_FLASH was not set in .config (so it
was not possible to use CONFIG_IS_ENABLED(DM_SPI_FLASH) in SPI DM/DTS
converted drivers), but it was set in u-boot.cfg file.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
This patch fixes issue with defining the DM_SPI_FLASH in the
configs/include/<board.h> instead of enabling this option in Kconfig.
The problem is that CONFIG_IS_ENABLED(DM_SPI_FLASH) shows false as there
is no DM_SPI_FLASH=y in .config (but the define is set in u-boot.cfg).
As a result conversion of DM_SPI_FLASH to using CONFIG_IS_ENABLED() is not
working properly.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.
Before this change it was necessary to use:
/* SPI Flash Configs */
#if defined(CONFIG_SPL_BUILD)
#undef CONFIG_DM_SPI
#undef CONFIG_DM_SPI_FLASH
#undef CONFIG_SPI_FLASH_MTD
#endif
in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.
The goal of this patch:
Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.
Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).
In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):
- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
environment with no fitImage and OF_LIBFDT support).
Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.
This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the setting for noc remap out of SPL code. Changing
noc remap inside SPL results in breaking back to BROM
boot.
Fixes commit c14fe2a8e1 ("rockchip: rk3188: Move SoC
one time setting into arch_cpu_init()").
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
While in most cases CSF_SIZE is handled via Kconfig we have some i.MX8M
platforms that set the size based on the now-renamed CONFIG_SECURE_BOOT
symbol. Update things so that CSF_SIZE itself depends on IMX_HAB being
enabled and provide the default value for i.MX8M family of parts.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Ye Li <ye.li@nxp.com>
There are a few remaining places where we say CONFIG_SECURE_BOOT rather
than CONFIG_IMX HAB. Update these instances.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Fix EMAC register address calculation, address need to multiply
with sizeof(u32) or 4.
This fixes write to invalid address.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
We don't really want to have ARM-specific code in a generic file. Create
a new arch-specific function to hold it, and move it into that.
Make the function weak so that any arch can implement it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since commit:
commit 6333cbb381
Author: Michael Walle <michael@walle.cc>
Date: Thu May 7 00:11:58 2020 +0200
phy: atheros: ar8035: remove static clock config
We can configure the clock output in the device tree. Disable the
hardcoded one in here. This is highly board-specific and should have
never been enabled in the PHY driver.
If bisecting shows that this commit breaks your board it probably
depends on the clock output of your Atheros AR8035 PHY. Please have a
look at doc/device-tree-bindings/net/phy/atheros.txt. You need to set
"clk-out-frequency = <125000000>" because that value was the hardcoded
value until this commit.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
, the clock output setting for the AR803x driver is removed from being
hardcoded in the PHY driver and should be passed via device tree instead.
Update the device tree with the "qca,clk-out-frequency" property so that
Ethernet can work again.
Reported-by: Soeren Moch <smoch@web.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Soeren Moch <smoch@web.de>
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
=2Yuu
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.10
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
XDP - Xilinx Drone Platform is a board for drones or other UAV.
Pinmux the SD card by default, and if the SD card detect line is high
(inactive) then pinmux the SD1 interface to EMIO instead. SD is placed on
extension card and shares connection with on board wife. That means that
when SD card is present in the board wifi can't be used.
There seems to be an issue with DDR access from PL at 2400MT/s, after
updating the PMU and ATF firmware this is causing extremely slow DDR
access. Reducing the DDR speed from 2400 to 2133 appears to solve that
issue, even though the hardware has proven to be 2400 capable.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change mini u-boot qspi spi-max-frequency to 108Mhz, make the
frequency similar to full u-boot qspi flash spi-max-frequency.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current aliases missed gpio0 node, and this node shoud be
aliased to gpio index 0 to align with i.MX8QXP. Otherwise, we
will get below message when running "gpio status" command, and
see the reason by "dm uclass".
=> gpio status
Device 'gpio@5d090000': seq 0 is in use by 'gpio@5d080000'
Device 'gpio@5d0a0000': seq 1 is in use by 'gpio@5d090000'
Device 'gpio@5d0b0000': seq 2 is in use by 'gpio@5d0a0000'
=> dm uclass
uclass 36: gpio
0 * gpio@5d080000 @ fbaefb90, seq 0, (req -1)
1 * gpio@5d090000 @ fbaefc70, seq 1, (req 0)
2 * gpio@5d0a0000 @ fbaefd50, seq 2, (req 1)
3 * gpio@5d0b0000 @ fbaefe30, seq 5, (req 2)
4 * gpio@5d0c0000 @ fbaeff10, seq 3, (req 3)
5 * gpio@5d0d0000 @ fbaefff0, seq 4, (req 4)
6 * gpio@5d0e0000 @ fbaf00d0, seq 6, (req 5)
7 * gpio@5d0f0000 @ fbaf01b0, seq 7, (req 6)
Signed-off-by: Ye Li <ye.li@nxp.com>
Select default U-Boot and SPL text base for the MX7 SoC. The U-Boot
text base is picked as the one used by various MX7 boards. The SPL
text base however is different.
The SPL text base is set to 0x912000 instead of the usual 0x911000,
that is because the 0x911000 value cannot work. Using 0x911000 as a
SPL text base will result in the DCD header being placed below the
0x911000 address, which is a reserved SRAM area which must not be
used. This will actually trigger eMMC boot failure on MX7D at least.
Hence the increment.
Update all boards affected by this SPL problem to the new SPL_TEXT_BASE.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
There are systems where board_early_init_f() is plain empty. Switch
the config option from "select" to "imply", to permit user to unset
the BOARD_EARLY_INIT_F if it were to be empty.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The iMX7 defines further DDRC ZQCTLx registers, however those were
thus far missing from the list of registers and not programmed. On
systems with LPDDR2 or DDR3, those registers must be programmed with
correct values, otherwise the DRAM may not work. However, existing
systems which worked without programming these registers before are
now setting those registers to 0, which is the default value, so no
functional change there.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode)
the correct phy-mode should be "rgmii-id", so fix it accordingly
to fix the Ethernet regression.
This problem has been exposed by commit:
commit 13114f38e2
Author: Vladimir Oltean <vladimir.oltean@nxp.com>
Date: Thu May 7 00:11:51 2020 +0200
phy: atheros: Explicitly disable RGMII delays
To eliminate any doubts about the out-of-reset value of the PHY, that
the driver previously relied on.
If bisecting shows that this commit breaks your board you probably have
a wrong PHY interface mode. You probably want the
PHY_INTERFACE_MODE_RGMII_RXID or PHY_INTERFACE_MODE_RGMII_ID mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode)
the correct phy-mode should be "rgmii-id", so fix it accordingly
to fix the Ethernet regression.
This problem has been exposed by commit:
commit 13114f38e2
Author: Vladimir Oltean <vladimir.oltean@nxp.com>
Date: Thu May 7 00:11:51 2020 +0200
phy: atheros: Explicitly disable RGMII delays
To eliminate any doubts about the out-of-reset value of the PHY, that
the driver previously relied on.
If bisecting shows that this commit breaks your board you probably have
a wrong PHY interface mode. You probably want the
PHY_INTERFACE_MODE_RGMII_RXID or PHY_INTERFACE_MODE_RGMII_ID mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix the phy-mode accordingly to fix the regression.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Sync the device tree with 5.8-rc1.
It basically contains the following extra kernel commit:
commit 86b08bd5b99480b79a25343f24c1b8c4ddcb5c09
Author: Russell King <rmk+kernel@armlinux.org.uk>
Date: Wed Apr 15 16:44:17 2020 +0100
ARM: dts: imx6-sr-som: add ethernet PHY configuration
Add ethernet PHY configuration ahead of removing the quirk that
configures the clocking mode for the PHY. The RGMII delay is
already set correctly.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
, which passes the 'qca,clk-out-frequency' property and it is important
to specify the correct frequency generated by the AR8035.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tom Rini <trini@konsulko.com>
The cd-gpios with (GPIO_ACTIVE_LOW | GPIO_PULL_UP) gpio is thus far
unsupported, reinstate the old cd-gpios behavior until this handling
is fully implemented. This avoid potential issue for SDCard boot:
the card detect fails with floating gpio.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The cd-gpios with (GPIO_ACTIVE_LOW | GPIO_PULL_UP) gpio is thus far
unsupported, reinstate the old cd-gpios behavior until this handling
is fully implemented. This permits the DHSOM to boot from SD again,
without this patch the card detect fails.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
- use 'vidconsole' stdout in nitrogen6x upgrade script
- add option for selection of the vidconsole commands
lcdputs and setcurs
- allow building ipuv3 driver with disabled CONFIG_PANEL
- make backlight and panel drivers optional
- remove useless code from ipuv3 driver
- extend existing DM_VIDEO work-around for console name
to support 'vga'
- remove non-DM code in ipuv3
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXuvRkA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXMpeAJkB/FzsJ3O7putHrbLKOrLRF3zZYwCfQxa9jKuh
DXNTYVrHS/43T8ijGYo=
=7G75
-----END PGP SIGNATURE-----
Merge tag 'video-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-video into next
- migrate remaining imx5/imx6qd boards to DM_VIDEO
- use 'vidconsole' stdout in nitrogen6x upgrade script
- add option for selection of the vidconsole commands
lcdputs and setcurs
- allow building ipuv3 driver with disabled CONFIG_PANEL
- make backlight and panel drivers optional
- remove useless code from ipuv3 driver
- extend existing DM_VIDEO work-around for console name
to support 'vga'
- remove non-DM code in ipuv3
The PSCI nodes are currently not populated for the Tegra210 and Tegra186
devices. This prevents the PSCI driver from being able to identify the
PSCI method used by these devices and causes the probe of the PSCI
driver to fail.
Since commit 81ea00838c ("efi_loader: PSCI reset and shutdown") was
added, which moves the PSCI EFI system reset handler into the PSCI
driver, this has prevented the EFI system reset from working for
Tegra210 and Tegra186. Therefore, populating these nodes is necessary
to fix the EFI system reset for Tegra210 and Tegra186.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
cfb_console driver uses 'vga' console name and we still have board
environments defining this name. Re-use existing DM_VIDEO work-
around for console name to support 'vga' name in stdout environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Soeren Moch <smoch@web.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
According to the linker script for both armv7 and arm926ejs based SoC,
BSS section was all the time separated for SPL but this symbol was
only enabled on some boards. However, it is necessary to have it
enabled for OF_SEPARATE configuration where DTB is appended to u-boot
with DTB.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Copy all device tree files required for omap4 sdp4430 support from
mainline Linux.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add OP-TEE firmware node in stm32mp15 U-Boot DTSI. This node is
needed since commit [1] that changed U-Boot/stm32mp15 to detect
OP-TEE availability by probing the resource instead of relying on
U-Boot configuration. The software sequence implemented by [1] is
fine but U-Boot DTS/DTSI files were not updated accordingly since,
hence OP-TEE presence is never detected by U-Boot, preventing Linux
kernel from using OP-TEE resources.
For consistency and to synchronize stm32mp15 DTSI files (excluding
U-Boot specific DTSI files) with the Linux kernel ones, this change
also moves the OP-TEE reserved memory nodes from board generic DTSI
files to U-Boot specific board DTSI files.
Link: [1] commit 43df0a159d ("stm32mp1: dynamically detect op-tee presence")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Fix the sequence in stm32mp1 fdt.c that disables OP-TEE resources
defined in FDT when U-boot detects OP-TEE firmware is not present.
Before this change, helper function stm32_fdt_disable_optee()
set property status to "disabled" for the OP-TEE reserved memory
nodes but this has no impact since Linux kernel does not consider
the status property for reserved-memory subnodes. This change
make U-Boot to attempt to delete the node instead.
Fixes: 4a1b975dac ("board: stm32mp1: reserve memory for OP-TEE in device tree")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change DT compatibility name to match change in driver's name.
Remove unused io_ds and fifo_mode fields from DT.
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Tom Rini <trini@konsulko.com>
Commit e71b6f6622 ("i2c: designware_i2c: Rewrite timing calculation")
change the hcnt and lcnt timing calculation. New timing calculation is
based on calculation from Designware i2c databook.
After this new timing calculation, hcnt will have negative value
with i2c-scl-falling-time-ns 5000 that set in socfpga_cyclone5_socdk.dts.
This patch overwrite i2c-scl-falling-time-ns to 300ns (default SCL fall
time used in Designware i2c driver) for Uboot.
Before the fix:
=> i2c dev 0
Setting bus to 0
Failure changing bus number (-22)
After the fix:
=> i2c dev 0
Setting bus to 0
=> i2c probe
Valid chip addresses: 17 51 55 5B 5C 5E 66 68 70
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Cleanup this driver to use dt in U-boot and static platdata in SPL.
This requires the following steps:
1. Move all platdata assignment from probe() to ofdata_to_platdata().
This function is only called in U-boot.
2. Replicate all the platdata assignment being done in
ofdata_to_platdata() in the omapl138 board file. This data is used in
the SPL case where SPL_OF_CONTROL is not enabled.
3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig
This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL')
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This reverts commit 1f63ee6566.
As reported by Ye Li on ML:
1. Removing the image_offset will break secondary (redundant) boot support for sd and emmc.
2. When booting from emmc boot partition, the image_offset is 0. But the flash.bin
generated by mkimage with imximage-8mp-lpddr4.cfg is for sd. It expects to be burn at 32KB offset.
The fit offset 0x60000 has already included the 32KB offset. So when you burn this flash.bin
to emmc boot partition at offset 0, the fit offset should subtract the 32KB (0x60000 - 0x8000).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Convert the board to DM_ETH instead of legacy networking. This requires
a minor addition to the DT to satisfy the requirement for specifying a
PHY node. No functional change from board user perspective.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The iMX7D RM 9.2.4.9.3 Power removal flow Table 9-11. Re-enabling power
explicitly says both the DDR controller and the PHY must be reset in the
correct sequence. Currently the code only resets the controller. This
leads to a misbehavior where the system brings the DRAM up after reboot,
but the DRAM is unstable. Add the missing reset.
The easiest way to trigger this is by triggering WDT without having the
WDT assert WDOG_B signal, i.e. mw.w 0x30280000 0x25 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
When not booting from FlexSPI, the offset computation is:
offset = image_offset + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8000;
When booting from SD card or eMMC user partition, image_offset is
0x8000. It is useless to add and remove 0x8000.
When booting from other device, image_offset is 0 so this computation is wrong.
Simplfy this computation to work on all booting devices.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
With yModem the FIT Image is only supplied once, so we can only
seek forward in the yModem supplied image and never backwards.
With the recent changes to the SPL mechanism, including loading
U-Boot first, FDT after, then the loadables, we must also reorder
the FIT image script to make sure that the loadables are last in
the FIT image.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Accidentally submitted a patch with indentation not correct, let's fix it
by indenting wrong lines.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
So far the puma dts files only just included the main puma dtsi without
handling the actual baseboard and rk3399-puma.dtsi was very much
detached from the variant in the mainline Linux kernel.
Recent changes resulted in a strange situation with nonworking puma boards.
Commit ab800e5a6f ("arm: dts: rockchip: puma: move U-Boot specific bits to u-boot.dtsi")
moved the sdram include from rk3399-puma-ddrX.dts to new files
rk3399-puma-ddrx-u-boot.dtsi which were never included anywhere though.
Commit 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
replaced the rk3399-puma.dtsi nearly completely, but in the kernel
it definitly depends on a baseboard dts to actually enable peripherals
like sd-slot, uarts, etc.
So to untagle this and bring the whole thing more in line with mainline
Linux, bring the rk3399-puma-haikou.dts over as well, drop the separate
DDR-option devicetrees and instead replace them with a puma Kconfig option
to select and include the needed DDR variant.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tabs not spaces, so transform it to the common styling.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The regulator enable-gpio uses opposite values for the declaration
vs. the enable_active_low property, breaking the regulator enablement.
Make the usbhost-supply work again by bringing them in sync again.
This mimics the upstream Linux change found on:
http://lore.kernel.org/r/20200604091239.424318-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The gmac reset has opposite values for the gpio declaration
and the separate reset-active, bring this in line to make
u-boot also find the ethernet-phy.
This mimics the upstream Linux commit found on
https://lore.kernel.org/r/20200603132836.362519-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The 'stdout-path' is missing after dts sync.
Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The ROCK-PI-E is a credit card size SBC based on Rockchip RK3328
Quad-Core ARM Cortex A53.
Net - Dual ethernet port, 1 X Gbe, 1 X 100M
USB - USB 3.0
DC - USB-Type C, 5V 2A
Storage - TF card, eMMC
Just build idbloader.img and u-boot.itb for Rockpi E board and
follow the blow steps to replace the relevant partition.
dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc
dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc
Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl7YxFMcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyJnICACR6Q6OclfIuM0A3ubV
GV48+iVz55eZnrZFKkbALBNjwTsshLpdZ/7Lr4zPD5e/FmrbJ+RONd0B6E38fSJk
Rq1ZwMyuR6yv+LAb9+La36tGqD9bCFewqBpR5LQNOdjE+fG66rrWxksMME1jOIr5
FLpFkk3lmEUloQumHDCQUgzXC/TUWpedgxpT15l1nR/Ovkh/MPvggIdS2zMWw92J
oA9shaNTVLd//W9icduXagNtRMsjscmf/zTZFCYgBRjUZgiPW+HnitWg7jqbYIuY
AqmNBZIrC6OuZ7W447g1rMGwbwQ5T9vbydp6PpHVqPvTt3D8OZ9h1+Hwwie7u9O1
CPaV
=xLcT
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2020.07-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2020.07 cycle
This set includes just two small commits that fix a build warning and
add a missing serial node.
This patch series addresses the following issues:
* allow compiling with clang
* add missing function descriptions to the HTML documentation
* simplify the validation of UEFI images
* validate load options in the UEFI boot manager
In a preparatory patch a structure definition is moved.
-----BEGIN PGP SIGNATURE-----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=rbBa
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc4
This patch series addresses the following issues:
* allow compiling with clang
* add missing function descriptions to the HTML documentation
* simplify the validation of UEFI images
* validate load options in the UEFI boot manager
In a preparatory patch a structure definition is moved.
On ARM systems gd is stored in register r9 or x18. When compiling with
clang gd is defined as a macro calling function gd_ptr(). So we can not
make assignments to gd.
In the UEFI sub-system we need to save gd when leaving to UEFI binaries and
have to restore gd when reentering U-Boot.
Define a new function set_gd() for setting gd and use it in the UEFI
sub-system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Tom Rini <trini@konsulko.com>
arch/arm/include/asm/system.h declares psci_arch_init(), but it is
surrounded by #ifdef CONFIG_ARMV8_PSCI.
psci_arch_init() is called for CONFIG_ARMV7_PSCI too. Add the missing
function declaration.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When compiling with CONFIG_SPL_SERIAL=n, gcc warns about
mbus_configure_port not being marked as static:
In file included from include/common.h:34,
from arch/arm/mach-sunxi/dram_sunxi_dw.c:11:
include/log.h:185:4: warning: 'printf' is static but used in inline function 'mbus_configure_port' which is not static
185 | printf(pr_fmt(fmt), ##args); \
| ^~~~~~
include/log.h:192:2: note: in expansion of macro 'debug_cond'
192 | debug_cond(_DEBUG, fmt, ##args)
| ^~~~~~~~~~
arch/arm/mach-sunxi/dram_sunxi_dw.c💯2: note: in expansion of macro 'debug'
100 | debug("MBUS port %d cfg0 %08x cfg1 %08x\n", port, cfg0, cfg1);
| ^~~~~
Fix this by updating the function accordingly.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
