Add features to write protect single boot area rather than all boot
areas.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Only newer eSDHC controllers set PRSSTAT_SDSTB flag. So do not wait until
flag PRSSTAT_SDSTB is set on old pre-2.2 controllers. Instead sleep for
fixed amount of time like it was before commit 6f883e501b ("mmc:
fsl_esdhc: Add emmc hs200 support").
This change fixes error 'Internal clock never stabilised.' which is printed
on P2020 board at every access to SD card.
Fixes: 6f883e501b ("mmc: fsl_esdhc: Add emmc hs200 support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
In order to have the possibility to configure the regulators at system
startup through DM support, all LDOs and bucks must be able to be
changeable. Currently there is a limitation to change the values when
the output is enabled. Since the driver is based on the ROHM BD71837 and a
comment that describes a limitation about switching while the output is
enabled can also be found there, the limitation probably comes from this type.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The generic ARM relocate_code function was using its own function entry
point as a relocation base, and it was obtaining that address by using
the "adr" instruction on that entry point label.
However that label is not just an ordinary label, instead we explicitly
mark it as a function start address. Normally that doesn't change much
(other than for debugging), but when assembled in Thumb mode, newer
versions of the GNU assembler prepare everything for this address being
used as the argument to a "bx" call, so make sure bit 0 is set in there
to mark this function as Thumb code. Of course this doesn't end up very
well when we use this address for the ensuing memcpy operation.
To avoid this problem, and to solve it in a robust way, add an extra
label, which is not marked as a function entry, and use that for the adr
instruction. This lets all assemblers generate the right immediate offset
in the "adr" instruction.
This fixes in particular ARMv7-M ports when using GNU binutils v2.37 or
newer (commit d3e52e120b68 seems to trigger the change in behaviour).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Jesse Taube <mr.bossman075@gmail.com>
fpga:
- Convert SYS_FPGA_CHECK_CTRLC and SYS_FPGA_PROG_FEEDBACK to Kconfig
- Add support for secure bitstream loading
spi:
- xilinx_spi: Add support for memopers and supports_op
- zynq_qspi: Add support for supports_op/child_pre_probe
- zynq_qspi: Fix dummy cycle and qspi speed calculations
xilinx:
- Get rid of #stream-id-cells
- Use fixed partitions for SOM
- Add support for UUID reading from FRU
- Use strlcpy instead of strncpy
- Add reset driver support for ZynqMP and Versal
- Enable power domain driver in ZynqMP and Versal
zynqmp:
- Do no place BSS at 0 which have issue with NULL pointer
- Enable SLG gpio driver
- Disable LMB for mini configurations
- Remove duplicate PMIO_NODE_ID_BASE macro
versal:
- Add xlnx-versal-resets.h header
mmc:
- zynq_sdhci: Fix macro for MMC HS
relocate-rela:
- Fix support for BE hosts
- Define all macros for e_machine and reloc types
misc:
- Get rid of guard macros from ARM and RISC-V
lmb:
- Add support for disabling LMB
serial:
- zynq: Fix baudrate calculation
tests:
- Mark bind tests to run only on sandbox
- List also dm uclass and devres
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYt/MrgAKCRDKSWXLKUoM
Idn1AKCZaIz+7b/si1+pTmdVqdFSd3GrigCeLlVkhR7lXm36fVsv0TCQr0mwJPc=
=KCC4
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.10-rc2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.10-rc2
fpga:
- Convert SYS_FPGA_CHECK_CTRLC and SYS_FPGA_PROG_FEEDBACK to Kconfig
- Add support for secure bitstream loading
spi:
- xilinx_spi: Add support for memopers and supports_op
- zynq_qspi: Add support for supports_op/child_pre_probe
- zynq_qspi: Fix dummy cycle and qspi speed calculations
xilinx:
- Get rid of #stream-id-cells
- Use fixed partitions for SOM
- Add support for UUID reading from FRU
- Use strlcpy instead of strncpy
- Add reset driver support for ZynqMP and Versal
- Enable power domain driver in ZynqMP and Versal
zynqmp:
- Do no place BSS at 0 which have issue with NULL pointer
- Enable SLG gpio driver
- Disable LMB for mini configurations
- Remove duplicate PMIO_NODE_ID_BASE macro
versal:
- Add xlnx-versal-resets.h header
mmc:
- zynq_sdhci: Fix macro for MMC HS
relocate-rela:
- Fix support for BE hosts
- Define all macros for e_machine and reloc types
misc:
- Get rid of guard macros from ARM and RISC-V
lmb:
- Add support for disabling LMB
serial:
- zynq: Fix baudrate calculation
tests:
- Mark bind tests to run only on sandbox
- List also dm uclass and devres
After we switch to use BINMAN_SYMBOLS, there is no need to pad
the file size to 0x8000 and 0x4000. After we use BINMAN_SYMBOLS,
the u-boot-spl-ddr.bin shrink about 36KB with i.MX8MP-EVK.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8m[m,n,p]-venice
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
By reading binman symbols, we no need hard coded IMEM_LEN/DMEM_LEN after
we update the binman dtsi to drop 0x8000/0x4000 length for the firmware.
And that could save binary size for many KBs.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8m[m,n,p]-venice
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
[Alper: Check BINMAN_SYMS_OK instead]
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
We are migrating to use binman symbols, the current names are
inconsistent across different boards, so unify them.
Also add `type = "blob-ext";`, since the new names are not valid binman
types.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8m[m,n,p]-venice
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
[Alper: Edit commit message]
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Since new atheros PHY driver needs to access its PHY node through
phy device, we have to assign the phy node in ethernet controller
driver. Otherwise the PHY driver will fail to get some nodes
and properties.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move i.MX code to a standalone file to make it easy for adding new
platform support
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move macros and structures to header file and make some functions
public, so that could used by other files, this is to
prepare split platform specific config to one file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When CONFIG_CLK is not enabled, there will be buil break:
"error: ‘eqos’ undeclared (first use in this function)"
Take eqos definition out the CONFIG_CLK ifdef.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set ARM clock to OD frequency 1.7Ghz, since we have set PMIC VDD_SOC
to Overdrive voltage 0.9V
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the DTSi file and DT header files for i.MX93 SoC
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add Kconfig for enabling reference events counter in DDRC performance
monitor by default
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since i.MX9 uses same DDR PHY with i.MX8M, split the DDRPHY to a common
directory under imx, then use dedicated ddr controller driver for each
iMX9 and iMX8M.
The DDRPHY registers are space compressed, so it needs conversion to
access the DDRPHY address. Introduce a common PHY address remap function
for both iMX8M and iMX9 for all PHY registers accessing.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement the DDR driver clock interfaces for set DDR rate and
bypass DDR PLL
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add bootaux command to support on-demand booting M33 from u-boot.
It kicks M33 via ATF by "bootaux 0x201e0000 0"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support on-demand booting M33 image from A core. SPL needs
to follow M33 kick up sequence to release M33 firstly,
then set M33 CPUWAIT signal. ATF will clear CPUWAIT to kick
M33 to run.
The prepare function also works around the M33 TCM ECC issue by
clean the TCM. Also enable sentinel handshake and WDOG1 clock
for M33 stop and reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add power init of MEDIAMIX, MLMIX and DDRMIX. And clear isolation
of MIPI DSI/CSI, USBPHY after the power up.
SPL should call the power init in its boot sequence before accessing
above three MIX and USB.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add GPIO registers structure for iMX93, so that we can enable lpgpio
driver
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sentinel have read access of OTP shadow register 0-511, and fsb have
read access of shadow 0-51/312-511.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX93 fuse can be accessed through FSB and s400-api. Add mapping tables
for i.MX93. The offset address of FSB accessing OTP shadow registers is
different between i.MX8ULP and i.MX93, so use macro to define the offset
address instead of hardcode.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The i.MX93 platform wants to reuse drivers/misc/imx8ulp/fuse.c. Moving
fuse.c from the folder imx8ulp to sentinel makes it can be used by other
platforms.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the get chip revision methond to use S400 API, also record
other information like lifecycle and UID to global data.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add TRDC driver to iMX9. The TRDC init splits to two phases:
1. Early init phase will release TRDC from Sentinel and open write
permission to the memory where SPL image runs. Sentinel will set
the memory to RX only after ROM authentication for the OEM
closed part.
2. Init phase will configure TRDC to allow non-secure master to
access DDR. So the peripherals can work in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce Sentinel API ahab_release_m33_trout to make sure sentinel
release M33 trout and make sure M33 could boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support more RDC instances on i.MX93, update API to latest
definition.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since iMX9 uses S401 which shares the API with iMX8ULP. So move S400
MU driver and API to a common place and selected by CONFIG_IMX_SENTINEL
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX9 shares same ROM API with i.MX8ULP, so make the i.MX8ULP the function
prototype common and usable by i.MX9.
Also include mmc env functions that use ROM API.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add timer_init to update ARM arch timer with correct frequency
from system counter and enable system counter.
Signed-off-by: Jian Li <jian.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add clock API to support CCM root clock and LPCG setting
Set the CCM AUTHEN register to allow non-secure world to set
root clock and lpcg.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
