Commit graph

202 commits

Author SHA1 Message Date
Stephen Warren
4ff213b8e4 ARM: tegra: clamp inputs on Jetson TK1
The HW-defined procedure for booting Tegra requires that
CLAMP_INPUTS_WHEN_TRISTATED be enabled before programming the pinmux.
Modify the Jetson TK1 board to do this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-05-13 10:41:32 -07:00
Stephen Warren
9348532f51 ARM: tegra: make use of GPIO init table on Jetson TK1
The HW-defined procedure for booting Tegra requires that some pins be
set up as GPIOs immediately at boot in order to avoid glitches on those
pins, when the pinmux is programmed. This patch implements this
procedure for Jetson TK1. For pins which are to be used as GPIOs, the
pinmux mux function need not be programmed, so the pinmux table is also
adjusted.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-05-13 10:41:32 -07:00
Stefan Agner
8f9fd6caaf usb: tegra: combine header file
Combine the Tegra USB header file into one header file for all SoCs.
Use ifdef to account for the difference, especially Tegra20 is quite
different from newer SoCs. This avoids duplication, mainly for
Tegra30 and newer devices.

Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:06 -07:00
Stephen Warren
e04bfdacb3 ARM: tegra: add Jetson TK1 board
Jetson TK1 is an NVIDIA Tegra124 reference board, which shares much of
its design with Venice2.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:06 -07:00
Stephen Warren
d68c942927 ARM: tegra: Tegra124 pinmux cleanup
This renames all the pinmux pins, drive groups, and functions so they
have a prefix which matches the type name. These lists are also auto-
generated using scripts that were also used to generate the kernel
pinctrl drivers. This ensures that the lists are consistent between the
two.

The entries in tegra124_pingroups[] are all updated to remove the columns
which are no longer used.

All affected code is updated to match.

There are differences in the set of drive groups. I have validated this
against the TRM. There are differences order of pin definitions in
pinmux.c; these previously had significant mismatches with the correct
order:-( I adjusted a few entries in pinmux-config-venice2.h since the
set of legal functions for some pins was updated to match the TRM.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:06 -07:00
Stephen Warren
1fa3a63413 ARM: tegra: Tegra114 pinmux cleanup
This renames all the pinmux pins, drive groups, and functions so they
have a prefix which matches the type name. These lists are also auto-
generated using scripts that were also used to generate the kernel
pinctrl drivers. This ensures that the lists are consistent between the
two.

The entries in tegra114_pingroups[] are all updated to remove the columns
which are no longer used.

All affected code is updated to match.

This introduces a few changes to pin/group/function naming and the set of
available functions for each pin. The new values now exactly match the
TRM; the chip documentation. I adjusted a few entries in
pinmux-config-dalmore.h due to this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:06 -07:00
Stephen Warren
803d01edc2 ARM: tegra: Tegra30 pinmux cleanup
This renames all the pinmux pins, drive groups, and functions so they
have a prefix which matches the type name. These lists are also auto-
generated using scripts that were also used to generate the kernel
pinctrl drivers. This ensures that the lists are consistent between the
two.

The entries in tegra30_pingroups[] are all updated to remove the columns
which are no longer used.

All affected code is updated to match.

This introduces a few changes to pin/group/function naming and the set of
available functions for each pin. The new values now exactly match the
TRM; the chip documentation. I adjusted one entry in
pinmux-config-cardhu.h due to this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:05 -07:00
Stephen Warren
70ad375ee4 ARM: tegra: Tegra20 pinmux cleanup
This renames all the Tegra20 pinmux pins and functions so they have a
prefix which matches the type name.

The entries in tegra20_pingroups[] are all updated to remove the columns
which are no longer used.

All affected code is updated to match.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:05 -07:00
Stephen Warren
dfb42fc95d ARM: tegra: pinmux naming consistency fixes
Clean up the naming of pinmux-related objects:
* Refer to drive groups rather than pad groups to match the Linux kernel.
* Ensure all pinmux API types are prefixed with pmux_, values (defines)
  are prefixed with PMUX_, and functions prefixed with pinmux_.
* Modify a few type names to make their content clearer.
* Minimal changes to SoC-specific .h/.c files are made so the code still
  compiles. A separate per-SoC change will be made immediately following,
  in order to keep individual patch size down.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:05 -07:00
Stephen Warren
07bbd48b47 ARM: tegra: prototype pinmux_init() in board.h
pinmux_init() is a board-level function, not a pinmux driver function.
Move the prototype to a board header rather than the driver header.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:05 -07:00
Stephen Warren
352580870c ARM: tegra: make all I2C ports open-drain
I2C protocol requires open-drain IOs. Fix the Dalmore and Venice2 pinmux
tables to configure the IOs correctly. Without this, Tegra may actively
drive the lines high while an external device is actively driving the
lines low, which can only lead to bad things.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-03-26 15:20:56 -07:00
Masahiro Yamada
3241e3d08c venice2: move device tree to fix build error
Commit 5ab502cb gathered all device tree sources
to arch/$(ARCH)/dts/.
So tegra124-venice2.dts also must go to arch/arm/dts directory
to build venice2 board.

(Commit 5ab502cb had been posted before venice2 board support
was merged. So an unvisible conflict happened.)

Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
2014-02-20 12:00:20 -05:00
Masahiro Yamada
5ab502cb89 dts: move device tree sources to arch/$(ARCH)/dts/
Unlike Linux Kernel, U-Boot historically had *.dts files under
board/$(VENDOR)/dts/ and *.dtsi files under arch/$(ARCH)/dts/.

I think arch/$(ARCH)/dts dicretory is a better location
to store both *.dts and *.dtsi files.

For example, before this commit, board/xilinx/dts directory
had both Microblaze dts (microblaze-generic.dts) and
ARM dts (zynq-*.dts), which are totally unrelated.

This commit moves *.dts to arch/$(ARCH)/dts/ directories,
allowing us to describe nicely mutiple DTBs generation in the next commit.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19 11:10:05 -05:00
Masahiro Yamada
9e4140329e kbuild: change out-of-tree build
This commit changes the working directory
where the build process occurs.

Before this commit, build process occurred under the source
tree for both in-tree and out-of-tree build.

That's why we needed to add $(obj) prefix to all generated
files in makefiles like follows:
  $(obj)u-boot.bin:  $(obj)u-boot

Here, $(obj) is empty for in-tree build, whereas it points
to the output directory for out-of-tree build.

And our old build system changes the current working directory
with "make -C <sub-dir>" syntax when descending into the
sub-directories.

On the other hand, Kbuild uses a different idea
to handle out-of-tree build and directory descending.

The build process of Kbuild always occurs under the output tree.
When "O=dir/to/store/output/files" is given, the build system
changes the current working directory to that directory and
restarts the make.

Kbuild uses "make -f $(srctree)/scripts/Makefile.build obj=<sub-dir>"
syntax for descending into sub-directories.
(We can write it like "make $(obj)=<sub-dir>" with a shorthand.)
This means the current working directory is always the top
of the output directory.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
2014-02-19 11:07:50 -05:00
Tom Warren
f7dc4ac37c ARM: tegra: add Venice2 (Tegra124) board
These are the board files for Venice2 (Tegra124), plus the AS3722 PMIC
files. PMIC init will be moved to pmic_common_init later.

This builds/boots on Venice2, SPI/MMC/USB/I2C all work. Audio, display
and WB/LP0 are not supported yet.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:47 -07:00
Tom Warren
a57c5846a2 ARM: tegra: add DT files for Tegra124 and Venice2
These are fairly complete, and near-clones of Tegra114 Venice, with an
additional I2C port, and MMC address changes for Tegra124.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:47 -07:00
Tom Warren
dcd12518b1 ARM: tegra: only build __pinmux_nand() when it's needed
__pinmux_nand() won't compile if PERIPH_ID_NDFLASH isn't defined.
Prevent this from causing build problems on newer SoCs without NAND
support (or without SW support for NAND yet), but preventing
compilation unless the function will actually be used, i.e. when
CONFIG_TEGRA_NAND is defined.

Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, rewrote commit description, moved ifdef around whole function
rather than just body]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:46 -07:00
Darwin Rambo
de351d6be6 lib: time: add weak timer_init() function
If timer_init() is made a weak stub function, then it allows us to
remove several empty timer_init functions for those boards that
already have a timer initialized when u-boot starts. Architectures
that use the timer framework may also remove the need for timer.c.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
2014-01-24 16:59:06 -05:00
Masahiro Yamada
e5c5301f14 Makefile: make directories by Makefile.build
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-17 14:11:31 -05:00
Masahiro Yamada
3bddafaab4 Makefile: convert makefiles to Kbuild style and delete grep switch
We have converted all makefiles needed to build $(LIBS).

Until this commit we used to grep switch so that U-Boot style
and Kbuild style makefiles coexist.
But we do not need any more.

Goint forward, use always Kbuild style Makefile when adding
a new Makefile

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-01 11:42:13 -04:00
Masahiro Yamada
a79854a90f board: arm: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Tom Rini <trini@ti.com>
2013-11-01 11:42:12 -04:00
Mateusz Zalega
16297cfb2a usb: new board-specific USB init interface
This commit unifies board-specific USB initialization implementations
under one symbol (usb_board_init), declaration of which is available in
usb.h.

New API allows selective initialization of USB controllers whenever needed.

Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
2013-10-20 23:42:40 +02:00
Tom Rini
c2120fbfbc Merge branch 'master' of git://git.denx.de/u-boot-i2c
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
	board/sandburst/common/ppc440gx_i2c.c
	board/sandburst/common/ppc440gx_i2c.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:50:24 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Simon Glass
1f2ba722ac tegra: i2c: Enable new CONFIG_SYS_I2C framework
This enables CONFIG_SYS_I2C on Tegra, updating existing boards and the Tegra
i2c driver to support this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
2013-07-23 08:34:55 +02:00
Stephen Warren
d035fcf9b6 ARM: tegra: enable LCD panel on Ventana
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-07-11 14:15:16 -07:00
Stephen Warren
b46694df84 ARM: tegra: enable LCD panel on Harmony
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-07-11 14:15:16 -07:00
Jim Lin
7e44d9320e ARM: Tegra: USB: EHCI: Add support for Tegra30/Tegra114
Tegra30 and Tegra114 are compatible except PLL parameters.

Tested on Tegra30 Cardhu, and Tegra114 Dalmore
platforms. All works well.

Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-07-11 14:15:15 -07:00
Jim Lin
56867d88c4 ARM: Tegra: FDT: Add USB EHCI function for T30/T114
Add DT node for USB EHCI function.
Add support for T30-Cardhu, T30-Beaver, T114-Dalmore boards.

Signed-off-by: Jim Lin <jilin@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-07-11 14:15:15 -07:00
Tom Warren
dcfe863838 Tegra: T30: Beaver: Fix board/board_name env vars, s/b beaver, not cardhu
Did a 'strings u-boot-dtb-tegra.bin | less' and saw that both
board and board_name == beaver. Didn't test as I have no T30
Beaver board here.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
2013-05-28 12:58:41 -07:00
Tom Warren
601795462a Tegra: T30: Beaver board support.
Beaver is a Tegra30 board that is nearly 100% compatible w/Cardhu.
Add a Beaver build so it can begin to be differentiated, if need be.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-04-15 16:13:51 -07:00
Tom Warren
49493cb714 Tegra: Split tegra_get_chip_type() into soc & sku funcs
As suggested by Stephen Warren, use tegra_get_chip() to return
the pure CHIPID for a Tegra SoC (i.e. 0x20 for Tegra20, 0x30 for
Tegra30, etc.) and rename tegra_get_chip_type() to reflect its true
function, i.e. tegra_get_chip_sku(), which returns an ID like
TEGRA_SOC_T25, TEGRA_SOC_T33, etc.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-04-15 11:01:38 -07:00
Tom Warren
6d9ea159e4 Tegra114: MMC: Add SD bus power-rail init routine
T114 requires SD bus power-rail bringup for the SDIO card on SDMMC3.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-25 09:56:07 -07:00
Tom Warren
2a04a31791 Tegra114: Dalmore: Add SDIO3 pad config to pinctrl_config table
SDIO1 (the SD-card slot on Dalmore) needs to have its pads setup
before the MMC driver is added.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-25 09:56:07 -07:00
Tom Warren
e9cd20654c Tegra114: fdt: Add SDMMC (sdhci) nodes for T114 boards (Dalmore for now)
Took these values directly from the kernel dts files.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-25 09:56:07 -07:00
Allen Martin
af77fdb2ce tegra114: dalmore: fdt: enable dalmore SPI controller
Dalmore has a SPI flash part attached to controller 4, so enable
controller 4 and set to 25MHz.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-25 09:56:07 -07:00
Allen Martin
78f47b7353 spi: add common fdt SPI driver interface
Add a common interface to fdt based SPI drivers.  Each driver is
represented by a table entry in fdt_spi_drivers[].  If there are
multiple SPI drivers in the table, the first driver to return success
from spi_init() will be registered as the SPI driver.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-25 09:56:06 -07:00
Allen Martin
ff1da6fb5f tegra: spi: rename tegra SPI drivers
Rename tegra SPI drivers to tegra20_flash and tegra20_slink in
preparation for commonization and addition of tegra114_spi.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-25 09:56:05 -07:00
Allen Martin
9000652da0 tegra: remove support for UART SPI switch
This feature was only used for tegra20 seaboard that had a pinmux
conflict on the SPI pins.  These boards were never manufactured, so
remove this support to clean up SPI driver.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-25 09:56:05 -07:00
Tom Warren
477393e787 Tegra114: Dalmore: Add pad config tables/code based on pinmux code
Pad config registers exist in APB_MISC_GP space, and control slew
rate, drive strengh, schmidt, high-speed, and low-power modes for
all of the pingroups in Tegra30. This builds off of the pinmux
way of constructing init tables to configure select pads (SDIOCFG,
for instance) during pinmux_init().

Currently, no padcfg entries exist. SDIO3CFG will be added when the
MMC driver is added as per the TRM to work with the SD-card slot on
Dalmore E1611.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:49:14 -07:00
Tom Warren
5647c03431 Tegra114: fdt: Move aliases from dtsi to dts file as per other Tegras
All other Tegra boards have their alias nodes in the .dts file

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:49:07 -07:00
Tom Warren
f31a5443a8 Tegra114: Dalmore: Always use DEFAULT instead of DISABLE for lock bits
The pinmux code issues a warning if the caller attempts to disable the
lock bit in a pinmux register, since this is impossible (once it's
locked, the only way to unlock it is to reset the device/pmt controller).

The I2C/DDC/CEC/USB macros expect a lock setting to be passed in,
and the previous setting of DISABLE caused the pinmux table parsing
code to issue the warning. Changing the lock bits in these table
entries to DEFAULT (i.e. don't touch it) fixes this.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:48:55 -07:00
Tom Warren
190be1f9b7 Tegra30: MMC: Add SD bus power-rail and SDMMC pad init routines
T30 requires specific SDMMC pad programming, and bus power-rail bringup.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:06:44 -07:00
Tom Warren
1baa4e72c6 Tegra30: fdt: Add SDMMC (sdhci) nodes for T30 boards (Cardhu for now)
Took these values directly from the kernel dts files.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:06:44 -07:00
Tom Warren
8ca79b2ff4 Tegra30: Cardhu: Add pad config tables/code based on pinmux code
Pad config registers exist in APB_MISC_GP space, and control slew
rate, drive strengh, schmidt, high-speed, and low-power modes for
all of the pingroups in Tegra30. This builds off of the pinmux
way of constructing init tables to configure select pads (SDIOCFG,
for instance) during pinmux_init().

Currently, only SDIO1CFG is changed as per the TRM to work with
the SD-card slot on Cardhu.

Thanks to StephenW for the suggestion/original idea.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:06:43 -07:00
Tom Warren
8b7776b9f9 Tegra114: pinmux: Update pinmux tables & code, fix a bug w/SDMMC3 init
Use the latest tables & code from our internal U-Boot repo.
The SDMMC3_CD, CLK_LB_IN and CLK_LB_OUT offsets in the pingroup
table were off by a few indices, causing the pinmux init code to
write bad data to the PINMUX_AUX_ regs. This also enabled the lock
bit, which made it impossible to reconfig the pads correctly for
SDMMC3 (SD card on Dalmore) operation. Also fixes SPI_CS2_N,
USB_VBUS_EN0, HDMI_CEC and UART2_RXD/TXD muxes.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:06:43 -07:00
Tom Warren
bb638bb756 Tegra30: Cardhu: Remove unneeded cardhu.c.mmc file
This was an older debug/developmental file that got added
accidentally. Not needed/used in any Cardhu build.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:06:43 -07:00
Tom Warren
527519ae69 Tegra30: fdt: Sync DT nodes with kernel DT files (I2C, SPI, GPIO, clock)
Minor edits to clock, apbdma and SPI, make I2C match kernel DT, and add gpio

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:06:43 -07:00
Tom Warren
73bb244394 Tegra: fdt: Remove memreserve line from Cardhu/Seaboard DT files
Not used, and wrong in Cardhu's case

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:06:42 -07:00
Tom Warren
c9aa831ee2 Tegra: MMC: Add DT support to MMC driver for all T20 boards
tegra_mmc_init() now parses the DT info for bus width, WP/CD GPIOs, etc.
Tested on Seaboard, fully functional.

Tamonten boards (medcom-wide, plutux, and tec) use a different/new
dtsi file w/common settings.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:06:42 -07:00
Tom Warren
126685ad44 Tegra: fdt: Add/enhance sdhci (mmc) nodes for all T20 DT files
Linux dts files were used for those boards that didn't already
have sdhci info populated. Tamonten has their own dtsi file with
common sdhci nodes (sourced from Linux).

Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:06:42 -07:00
Tom Warren
6c5be646b4 Tegra: fdt: Change /include/ to #include for C preprocessor
dts Makefile has the arch & board include paths added to DTS_CPPFLAGS.
This allows the use of '#include "xyz"' in the dts/dtsi file which
helps the C preprocessor find common dtsi include files.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:06:42 -07:00
Tom Warren
b77c3547e8 Tegra114: fdt: Update DT files with I2C info for T114/Dalmore
T114, like T30, does not have a separate/different DVC (power I2C)
controller like T20 - all 5 I2C controllers are identical, but
I2C5 is used to designate the controller intended for power
control (PWR_I2C in the schematics). PWR_I2C is set to 400KHz.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:06:41 -07:00
Lucas Stach
7ae18f3725 tegra: usb: move implementation into right directory
This moves the Tegra USB implementation into the drivers/usb/host
directory. Note that this merges the old
/arch/arm/cpu/armv7/tegra20/usb.c file into ehci-tegra.c. No code
changes, just moving stuff around.

v2: While at it also move some defines and the usb.h header file to make
usb driver usable for Tegra30.
NOTE: A lot more work is required to properly init the PHYs and PLL_U on
Tegra30, this is just to make porting easier and it does no harm here.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-03-14 11:06:41 -07:00
Tom Warren
07067145de Tegra114: Add/enable Dalmore build (T114 reference board)
This build is stripped down. It boots to the command prompt.
GPIO is the only peripheral supported. Others TBD.

Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-02-11 10:35:26 -07:00
Tom Warren
94829195ac Tegra114: Add generic Tegra114 build support
This patch adds basic Tegra114 (T114) build support - no specific
board is targeted.

Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-02-11 10:35:26 -07:00
Tom Warren
8aff009585 Tegra114: Dalmore: Add DT files
These are stripped down for bringup, They'll be filled out later
to match-up with the kernel DT contents, and/or as devices are
brought up (mmc, usb, spi, etc.).

Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-02-11 10:35:25 -07:00
Allen Martin
b19f57491a tegra: add SPI SLINK driver
Add driver for tegra SPI "SLINK" style driver.  This controller is
similar to the tegra20 SPI "SFLASH" controller.  The difference is
that the SLINK controller is a genernal purpose SPI controller and the
SFLASH controller is special purpose and can only talk to FLASH
devices.  In addition there are potentially many instances of an SLINK
controller on tegra and only a single instance of SFLASH.  Tegra20 is
currently ths only version of tegra that instantiates an SFLASH
controller.

This driver supports basic PIO mode of operation and is configurable
(CONFIG_OF_CONTROL) to be driven off devicetree bindings.  Up to 4
devices per controller may be attached, although typically only a
single chip select line is exposed from tegra per controller so in
reality this is usually limited to 1.

To enable this driver, use CONFIG_TEGRA_SLINK

Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-02-11 10:35:25 -07:00
Allen Martin
23e3158f34 tegra30: fdt: add SPI SLINK nodes
Add tegra30 SPI SLINK nodes to fdt.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-02-11 10:35:24 -07:00
Allen Martin
36068ae75e tegra: fdt: add back missing host1x node
Add back host1x node to seaboard dts file.  This got dropped during
the tegra fdt sort.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-02-11 10:35:23 -07:00
Allen Martin
b7723f3f30 tegra: fdt: sort dts files
Sort nodes in dts files according the the following rules:

1) Any nodes that already exist in any /include/d file, in the order
they appear in the /include/d file.

2) Any nodes with a reg property, in order of their address.

3) Any nodes without a reg property, alphabetically by node name.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-01-17 09:07:34 -07:00
Allen Martin
d3f8752ed6 tegra: fdt: remove clocks nodes
These nodes are unused.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-01-17 09:07:23 -07:00
Allen Martin
d08b9e9c7e tegra: remove IRDA pinmux synonym
IRDA is a synonym for UARTB in tegra pinmux, remove all usage of this
synonym and replace with UARTB to disambiguate.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-01-16 13:40:08 -07:00
Tom Warren
083bbbbe77 Tegra30: fdt: Update DT files with I2C info for T30/Cardhu
Note that T30 does not have a separate/different DVC (power I2C)
controller like T20 - all 5 I2C controllers are identical, but
DVC_I2C is still used to designate the controller intended for
power control (PWR_I2C in the schematics). On Cardhu, it's used
to access the PMU and EEPROM, as well as the audio codec, temp
sensor, and fuel gauge devices from the OS.

Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-01-16 13:40:08 -07:00
Tom Warren
f01b631f7d Tegra30: Add/enable Cardhu build (T30 reference board)
This build is stripped down. It boots to the command prompt.
GPIO is the only peripheral supported. Others TBD.

include/configs/tegra-common.h now holds common config options
for Tegra SoCs.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-01-16 13:40:08 -07:00
Tom Warren
6d6c0baebe Tegra30: Add generic Tegra30 build support
This patch adds basic Tegra30 (T30) build support - no specific
board is targeted.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-01-16 13:40:08 -07:00
Tom Warren
79ce91bade Tegra30: Cardhu: Add DT files
These are stripped down for bringup, They'll be filled out later
to match-up with the kernel DT contents, and/or as devices are
brought up (mmc, usb, spi, etc.).

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-01-16 13:40:08 -07:00
Marc Dietrich
716d943983 tegra: display: add board pinmux
Boards may require a different pinmux setup for DISPALY than the default one.
Add a way to call into board specific code to set this up.

Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-01-16 13:40:07 -07:00
Stephen Warren
72573543b5 ARM: tegra: enable 8-bit SD slots in board files
Harmony contains an SD slot with all 8 bits routed. This allows plugging
in an eMMC-chip-in-SD-form-factor.

Seaboard/Springbank/Ventana/AC100 all have an eMMC chip with all 8 bits
hooked up.

Now that the U-Boot eMMC code fully supports 8-bit operation, initialize
those ports as 8-bit instead of 4-bit to improve performance.

Whistler was already registering its ports as 8-bit.

TrimSlice doesn't have any 8-bit ports.

I don't have any Avionic Design boards nor the Colibri board to test with.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-11-19 08:15:42 -07:00
Simon Glass
77139f5170 tegra: fdt: Add LCD definitions for Seaboard
The Seaboard has a 1366x768 16bpp LCD. The backlight is controlled
by one of the PWMs.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-11-19 08:15:39 -07:00
Simon Glass
1b24a50b44 tegra: Add LCD support to Nvidia boards
Add calls to the LCD driver from Nvidia board code.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-11-19 08:15:37 -07:00
Simon Glass
e1ae0d1f71 tegra: Add support for PWM
The pulse width/frequency modulation peripheral supports generating
a repeating pulse. It is useful for controlling LCD brightness.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-11-19 08:15:36 -07:00
Stephen Warren
a2ab6b7d32 ARM: tegra: don't request GPIO from Seaboard's SPL
Seaboard has a GPIO that switches an external mux between Tegra's debug
UART and SPI flash. This is initialized from the SPL so that SPL debug
output can be seen. Simplify the code that does this, and don't actually
request the GPIO in the SPL; just program it. This saves ~4.5K from the
size of the SPL, mostly BSS due to the large gpio_names[] table that is
no longer required. This makes Seaboard's SPL fit within the current max
size.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Allen Martin <amartin@nvidia.com>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-29 09:07:05 -07:00
Stephen Warren
da1f735272 ARM: tegra: select between Seaboard/Ventana at compile time
Seaboard and Ventana are very similar boards, and so share the seaboard.c
board file. The one difference needed so far is detected at run-time by
calling machine_is_ventana(). This bloats the Ventana build with code
that is never used. Switch to detecting Ventana at compile time to remove
bloat. This shaves ~5K off the SPL size on Ventana, and makes the SPL fit
within the max size.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-29 09:07:05 -07:00
Stephen Warren
56f42f85f5 ARM: tegra: Whistler: remove unused USB alias
Port USB1 on Whistler is intended as a device port for USB recovery.
Whistler's DT currently contains an alias for this USB port, even though
Whistler's config doesn't enable multiple USB controllers, so the alias
is unused. Remove the unused alias for consistency for now. Similar,
explicitly disable the port in the device tree too.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-29 09:07:05 -07:00
Stephen Warren
699c40e878 ARM: tegra: Harmony: enable ULPI USB port
The ULPI port is routed onto pins on the mini PCI Express connector. A
standard breakout board may be used to access the port.

* Add required DT entries to configure the ULPI port.
* Setup up the ULPI pinmux in the board code.
* Enable multiple USB controller and ULPI support in the board config.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-29 09:07:04 -07:00
Marc Dietrich
73286d8729 tegra: move common features to a common makefile
For Non-Nvidia boards to include newly added features (like emc clock
scaling) it would be necessary to add each feature to their own board
Makefile. This is because currently the top Makefile automaticly includes
these features only for Nvidia boards.

This patch adds a simple Makefile include so all new features become
available for non-Nvidia board vendors.

Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-29 09:07:04 -07:00
Lucas Stach
c0720afbb5 tegra: nand: add board pinmux
Boards may require a different pinmux setup for NAND than the default one.
Add a way to call into board specific code to set this up.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15 11:54:07 -07:00
Lucas Stach
516f00b324 tegra: clean up board include hell
The prototypes used in board files were all scattered out, which lead to
code duplication between SPL and normal U-Boot and some prototypes not actually
being used. Consolidate this in a common board header.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15 11:54:07 -07:00
Lucas Stach
0cd10c7abf tegra20: rework UART GPIO handling
Rename board provided gpio_config_uart() to
gpio_early_init_uart() as it does the same thing as the equally
called function provided by the uart-switch code. This allows
to simply call this function in early board init whether or not
we are building with CONFIG_UART_SWITCH defined.

Also provide a weak symbol for this function, to avoid the
need to provide this function for boards that don't need any
fixup.

This patch supersedes the earlier posted
"tegra: convert gpio_config_uart to weak symbol".
Build tested with MAKEALL -s tegra20

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15 11:54:07 -07:00
Tom Warren
150c24936b Tegra20: Move some include files to arch-tegra for sharing with Tegra30
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h.
Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs
that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20'
'root' file.

All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK.

Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15 11:54:06 -07:00
Tom Warren
29f3e3f248 Tegra: Change Tegra20 to Tegra in common code, prep for T30
Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate.
Convert tegra20_ source file and function names to tegra_, also.

Upcoming Tegra30 port will use common code/defines/names where possible.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
2012-09-10 13:01:24 -07:00
Stephen Warren
cf46cdebdd ARM: tegra: fix Ventana standalone build
Ventana always pulls in files from the Seaboard directory, so needs to
mkdir $(obj)../seaboard unconditionally. This fixes:

git clean -f -d -x
./MAKEALL ventana

"MAKEALL -s tegra20" passes without this change, because Seaboard
happens to be built before Ventana, and hence the directory has already
been created.

I believe the mkdir is only needed for out-of-tree builds, since the
seaboard directory is part of the source tree. However, since we always
build an SPL for Tegra now, which I believe is effectively an out-of-tree
build, we will always need this at some time. The overhead of just
uncondtionally executing the mkdir is minimal, and simplifies the
Makefile, since we don't need to code up the exact minimal condition to
execute the mkdir.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-09-07 13:54:32 -07:00
Stephen Warren
3aa7a6a635 ARM: tegra: remove redundant mkdirs from board Makefiles
None of harmony, seaboard, ventana, whistler directly build files from
../common/, so there's no need to mkdir the obj directory for such files.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-09-07 13:54:31 -07:00
Stephen Warren
9614a1e963 tegra: enable NAND on Harmony
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-09-07 13:54:31 -07:00
Simon Glass
7cedd1811a tegra: fdt: Add NAND definitions to fdt
Add a flash node to handle the NAND, including memory timings and
page / block size information.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-09-07 13:54:30 -07:00
Allen Martin
a49716aa7c tegra20: move SDRAM param save to later in boot
Move warmboot_save_sdram_params() to later in the boot sequence.  This
code relies on devicetree to get the address of the memory controller
and with upcoming changes for SPL boot it gets called early in the
boot process when devicetree is not initialized yet.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-09-01 14:58:22 +02:00
Allen Martin
45ec5b2579 tegra20: remove timer_init from SPL build
Don't use timer_init from tegra board.c.  This comes out of arm720t
for the SPL build.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-09-01 14:58:21 +02:00
Allen Martin
00a2749d7b tegra20: rename tegra2 -> tegra20
This is make naming consistent with the kernel and devicetree and in
preparation of pulling out the common tegra20 code.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-09-01 14:58:21 +02:00
Stephen Warren
e028494887 tegra: add pin_mux_spi() board initialization function
Boards can override this to set up the pinmux correctly to access serial
flash.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-09 22:44:33 +02:00
Tom Warren
1e2d785975 tegra: fix leftover CONFIG_TEGRA2_MMC & _SPI build switches
Missed some boards after my tegra2_mmc.* -> tegra_mmc.* change, and
one instance of CONFIG_TEGRA2_SPI. MAKEALL -s tegra2 AOK, Seaboard MMC
AOK. Didn't test Tamonten, Paz00 or TrimSlice, as I have none here.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
2012-07-09 22:44:32 +02:00
Thierry Reding
cb7a1cf36a tegra: Allow boards to perform early GPIO setup
The new gpio_early_init() function, which does nothing by default, can
be overridden by boards to configure GPIOs at an early stage.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-09 22:44:32 +02:00
Tom Warren
3f82d89d3d mmc: tegra2: rename tegra2_mmc.* to tegra_mmc.*
In anticipation of Tegra3 support, continue removing/renaming
Tegra2-specific files. No functional changes (yet).
Updated copyrights to 2012.

Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:20 +02:00
Tom Warren
edffa63d3d spi: tegra2: rename tegra2_spi.* to tegra_spi.*
In anticipation of Tegra3 support, start removing/renaming
Tegra2-specific files. No functional changes (yet).
Also updated copyright to 2012.

Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:20 +02:00
Stephen Warren
b1b9e4ce3a tegra: ventana: add own device tree, enable USB
Add a device tree for Ventana; the Seaboard file no longer represents
the HW present on Ventana.

Enable USB on Ventana.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:19 +02:00
Stephen Warren
f3d93309c1 tegra: harmony: add device tree support
... to enable USB host support, which enables Ethernet support.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:19 +02:00
Stephen Warren
d5ebc937c9 tegra: Whistler board support
Whistler is a highly configurable Tegra evaluation and development board.
This change adds support for the following specific configuration:

E1120 motherboard
E1108 CPU board
E1116 PMU board

The motherboard configuration switches are set as follows:
SW1=0 SW2=0 SW3=5
S1/S2/S3/S4 all on, except S3 7/8 are off.

Other combinations of daugher boards may work to varying degrees, but will
likely require some SW adjustment.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:17 +02:00
Tom Warren
078078cfa9 spi: Tegra2: Seaboard: fix UART corruption during SPI transactions
Simon Glass's proposal to fix this on Seaboard was NAK'd, so I
removed his NS16550 references and added a small delay before
SPI/UART muxing. Tested on my Seaboard with large SPI reads/writes
and saw no corruption (crc's matched) and no spurious comm chars.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Jimmy Zhang <jimmzhang@nvidia.com>
2012-07-07 14:07:17 +02:00
Anton Staff
c3ab91f064 tegra: fdt: Add keyboard definitions for Seaboard
Seaboard uses a QUERTY keyboard. We add key codes for this to
enable key scanning to work.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15 08:31:40 +02:00
Simon Glass
d376e8d228 tegra: fdt: Add EMC data for Tegra2 Seaboard
This adds timings for T20 and T25 Seaboards, using the bindings found here:

http://patchwork.ozlabs.org/patch/132928/

We supply both full speed options for normal running, and half speed options
for testing / development.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15 08:31:39 +02:00