Commit graph

1958 commits

Author SHA1 Message Date
Ye Li
8af1caa237 sf: Add Macronix MX25R6435F SPI NOR flash to flash parameters array
On i.mx7ulp EVK board, we use MX25R6435F NOR flash, add its parameters
and IDs to flash parameter array. Otherwise, the flash probe will fails.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-11 01:30:49 +05:30
Dario Binacchi
1fbfe58df6 spi: fix dev parameter in dev_* calls
Probably the non-use of the device parameter by the print routines did
not generate compilation errors.

Signed-off-by: Dario Binacchi <dariobin@libero.it>
2020-05-11 01:30:49 +05:30
Han Xu
bf9382addf mtd: nand: raw: mxs_nand changes for nandbcb
Add more BCH setting mode and remove the unnecessary platform constrain

Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Alice Guo
fe04bcd7e8 nand: enable the Randomizer module for i.mx7 and i.mx8
To enable the Randomizer module, set GPMI_ECCCTRL[RANDOMIZER_ENABLE] to
1, then set GPMI_ECCCOUNT[RANDOMIZER_PAGE] to select randomizer page
number needed to be randomized.

Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Han Xu
f7bb012ab7 mxs_nand: don't check zero count when ECC reading with randomizer
When enabled randomizer during ECC reading, the controller reported it's
erased page. Checking zero count will cause data get modified to all
0xFF. Stop checking during randomizer to workaround this issue.

Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Ye Li
a59691280d MXS_NAND: Add clock support for iMX8
Since iMX8 has enabled clock uclass, we can parse the clocks from DTB
and enable them in GPMI driver.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Peng Fan
39320e7256 mtd: nand: support GPMI NAND driver for i.MX8
enable the GPMI NAND driver for i.MX8, i.MX8 use similar controller as
i.MX8M

- register definition for i.mx8
- DMA structure must be 32bit address

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Alice Guo
f290fe0a42 nand: mxs_nand: make imx8mm can use hardware BCH and randomizer
imx8mm needs to BCH encode and set NAND page number needed to be
randomized

modify conditional compilation

Use CONFIG_IMX8M, so it apply to imx8mq/mm/mn

Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Han Xu
17282f45ab mtd: mxs_nand: fix the gf_13/14 definition issue
gf_13/14 mask was not set correctly in register definition.

Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Han Xu
9fdb5f0a0c mtd: nand: mxs_nand: add i.MX6QP compatible string
add the dedicate compatible string for i.MX6QP

Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Ye Li
e551ee2dea mxs_nand: Update compatible string for i.MX6SX
The iMX6SX uses compatible string "fsl,imx6sx-gpmi-nand" for gpmi
node in DTS, so update the driver for the string

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Ye Li
b209635c7a nand: Update SPL MXS NAND mini driver
Update the mini driver to add support for getting ecc info from ONFI and
support read image data from page unaligned NAND address.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Ye Li
ff99041b3b mxs_nand: Add support for i.MX8M
Update the gpmi/apbh_dma/bch drivers and relevant registers for i.MX8M.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Peng Fan
29f40c07e7 nand: mxs: correct bitflip for erased NAND page
This patch is a porting of
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/
commit/?h=imx_4.1.15_1.0.0_ga&id=e4dacc44d22e9474ec456cb330df525cd805ea38
"
i.MX6QP and i.MX7D BCH module integrated a new feature to detect the
bitflip number for erased NAND page. So for these two platform, set the
erase threshold to gf/2 and if bitflip detected, GPMI driver will
correct the data to all 0xFF.

Also updated the imx6qp dts file to ditinguish the GPMI module for i.MX6Q
with the one for i.MX6QP.
"

In this patch, i.MX6UL is added and threshold changed to use ecc_strength.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Peng Fan
552c88273e nand: mxs: fix the bitflips for erased page when uncorrectable error
This patch is porting from linux:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/
?h=imx_4.1.15_1.0.0_ga&id=3d42fcece496224fde59f9343763fb2dfc5b0768

"
We may meet the bitflips in reading an erased page(contains all 0xFF),
this may causes the UBIFS corrupt, please see the log from Elie:

-----------------------------------------------------------------
[    3.831323] UBI warning: ubi_io_read: error -74 (ECC error) while reading 16384 bytes from PEB 443:245760, read only 16384 bytes, retry
[    3.845026] UBI warning: ubi_io_read: error -74 (ECC error) while reading 16384 bytes from PEB 443:245760, read only 16384 bytes, retry
[    3.858710] UBI warning: ubi_io_read: error -74 (ECC error) while reading 16384 bytes from PEB 443:245760, read only 16384 bytes, retry
[    3.872408] UBI error: ubi_io_read: error -74 (ECC error) while reading 16384 bytes from PEB 443:245760, read 16384 bytes
...
[    4.011529] UBIFS error (pid 36): ubifs_recover_leb: corrupt empty space LEB 27:237568, corruption starts at 9815
[    4.021897] UBIFS error (pid 36): ubifs_scanned_corruption: corruption at LEB 27:247383
[    4.030000] UBIFS error (pid 36): ubifs_scanned_corruption: first 6569 bytes from LEB 27:247383
-----------------------------------------------------------------

This patch does a check for the uncorrectable failure in the following steps:

   [0] set the threshold.
       The threshold is set based on the truth:
       "A single 0 bit will lead to gf_len(13 or 14) bits 0 after the BCH
        do the ECC."

        For the sake of safe, we will set the threshold with half the gf_len, and
        do not make it bigger the ECC strength.

   [1] count the bitflips of the current ECC chunk, assume it is N.

   [2] if the (N <= threshold) is true, we continue to read out the page with
       ECC disabled. and we count the bitflips again, assume it is N2.
       (We read out the whole page, not just a chunk, this makes the check
        more strictly, and make the code more simple.)

   [3] if the (N2 <= threshold) is true again, we can regard this is a erased
       page. This is because a real erased page is full of 0xFF(maybe also has
       several bitflips), while a page contains the 0xFF data will definitely
       has many bitflips in the ECC parity areas.

   [4] if the [3] fails, we can regard this is a page filled with the '0xFF'
       data.
"

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Ye Li
51cdf83eea mtd: gpmi: provide the option to use legacy bch geometry
Provide an option in DT to use legacy bch geometry, which compatible
with the 3.10 kernel bch setting. To enable the feature, adding
"fsl,legacy-bch-geometry" under gpmi-nand node.

NOTICE: The feature must be enabled/disabled in both u-boot and kernel.

Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Ye Li
616f03daba mtd: gpmi: change the BCH layout setting for large oob NAND
The code change updated the NAND driver BCH ECC layout algorithm to
support large oob size NAND chips(oob > 1024 bytes) and proposed a new
way to set ECC layout.

Current implementation requires each chunk size larger than oob size so
the bad block marker (BBM) can be guaranteed located in data chunk. The
ECC layout always using the unbalanced layout(Ecc for both meta and
Data0 chunk), but for the NAND chips with oob larger than 1k, the driver
cannot support because BCH doesn’t support GF 15 for 2K chunk.

The change keeps the data chunk no larger than 1k and adjust the ECC
strength or ECC layout to locate the BBM in data chunk. General idea for
large oob NAND chips is

1.Try all ECC strength from the minimum value required by NAND spec to
the maximum one that works, any ECC makes the BBM locate in data chunk
can be chosen.

2.If none of them works, using separate ECC for meta, which will add one
extra ecc with the same ECC strength as other data chunks. This extra
ECC can guarantee BBM located in data chunk, of course, we need to check
if oob can afford it.

Previous code has two methods for ECC layout setting, the
legacy_calc_ecc_layout and calc_ecc_layout_by_info, the difference
between these two methods is, legacy_calc_ecc_layout set the chunk size
larger chan oob size and then set the maximum ECC strength that oob can
afford. While the calc_ecc_layout_by_info set chunk size and ECC
strength according to NAND spec. It has been proved that the first
method cannot provide safe ECC strength for some modern NAND chips, so
in current code,

1. Driver read NAND parameters first and then chose the proper ECC
layout setting method.

2. If the oob is large or NAND required data chunk larger than oob size,
chose calc_ecc_for_large_oob, otherwise use calc_ecc_layout_by_info

3. legacy_calc_ecc_layout only used for some NAND chips does not contains
necessary information. So this is only a backup plan, it is NOT
recommended to use these NAND chips.

Signed-off-by: Han Xu <b45815@freescale.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Patrick Delaunay
c39e19a9b0 configs: migrate CONFIG_SYS_MTDPARTS_RUNTIME to defconfigs
Move CONFIG_SYS_MTDPARTS_RUNTIME into Kconfig done by moveconfig.py.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-08 09:16:26 -04:00
Tom Rini
b641dd3ec8 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-spi
- distro boot support for SPI flash
- sifive spi flash driver
2020-04-30 18:05:15 -04:00
Kuldeep Singh
685465fbba mtd: spi-nor-ids: Add Spansion s25fs512s flash entry
Spansion "s25fs512s" flash is incorrectly decoded as "s25fl512s" on
various platforms as former is not present. Add the entry.

Linux already has both the flashes present. A snippet below:
{ "s25fl512s",  INFO6(0x010220, 0x4d0080, 256 * 1024, 256...},
{ "s25fs512s",  INFO6(0x010220, 0x4d0081, 256 * 1024, 256...},

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-04-30 22:34:20 +05:30
Jagan Teki
a976238de3 mtd: spi-nor-ids: Enable 4B_OPCODES for is25wp256
IS25WP256 flash chips do support 4byte address opcodes,
so enable support for it.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Sagar Kadam <sagar.kadam@sifive.com>
2020-04-30 22:34:20 +05:30
Jagan Teki
5bf3f3dd11 mtd: spi-nor: Enable QE bit for ISSI flash
Enable QE bit for ISSI flash chips.

QE enablement logic is similar to what Macronix
has, so reuse the existing code itself.

Cc: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-04-30 22:34:20 +05:30
Tom Rini
6d7dacf726 Xilinx changes for v2020.07-rc2
mmc:
 - Fix dt property handling via generic function
 
 clk:
 - Fix versal watchdog clock setting
 
 nand:
 - Fix zynq nand command comparison
 
 xilinx:
 - Enable ubifs
 - Sync board_late_init configurations with initrd_high setup
 - Make custom distro boot more verbose
 
 zynq:
 - Kconfig alignments
 - Fix nand cse configuration
 
 zynqmp:
 - Fix zcu104 low level qspi configuration
 - Small DT updates
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXqp9yAAKCRDKSWXLKUoM
 IXiuAKCLjBKGQ+o+BkJMvjbydF1JgFdXpwCffFPRe6dTkPsLZhpzW/YQMrjidtg=
 =CQTb
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2020.07-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx changes for v2020.07-rc2

mmc:
- Fix dt property handling via generic function

clk:
- Fix versal watchdog clock setting

nand:
- Fix zynq nand command comparison

xilinx:
- Enable ubifs
- Sync board_late_init configurations with initrd_high setup
- Make custom distro boot more verbose

zynq:
- Kconfig alignments
- Fix nand cse configuration

zynqmp:
- Fix zcu104 low level qspi configuration
- Small DT updates

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-30 11:34:01 -04:00
Robert Marko
f5fba6e85b mtd: nand: spi: add support for Toshiba TC58CVG2S0HRAIJ
Toshiba recently launched new revisions of their serial SLC NAND series.
TC58CVG2S0HRAIJ is a refresh of previous series with minor improvements.
Basic parameters are same so lets add support for this new revision.

Datasheet: https://business.kioxia.com/info/docget.jsp?did=58601&prodName=TC58CVG2S0HRAIJ

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-04-29 01:44:35 +05:30
Robert Marko
8912710484 mtd: spi-nand: Import Toshiba SPI-NAND support
Linux has good support for Toshiba SPI-NAND, so lets import it.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-04-29 01:44:35 +05:30
Bacem Daassi
6f3b1f4a1d mtd: spi-nor: Enable dual and quad read for s25fl256s0
The s25fl256s0 supports dual and quad read like s25fl256s1.
Enable it by adding SPI_NOR_DUAL_READ and SPI_NOR_QUAD_READ
flags to the flash_info entry.
Tested on real silicon and confirmed to be working.

Signed-off-by: Bacem Daassi <Bacem.Daassi@cypress.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-04-29 01:44:35 +05:30
Kuldeep Singh
cae3c7cc58 mtd: spi-nor-ids: Enable SPI_NOR_OCTAL_READ flag for mt35xu*
Commit 658df8bd94 ("mtd: spi-nor-core: Add octal mode support")
enables octal mode(1-1-8) support in spi-nor framework.

mt35xu512aba and mt35xu02g supports SINGLE and OCTAL I/O. Hence, enable
SPI_NOR_OCTAL_READ flag for these flashes.

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-04-29 01:44:35 +05:30
Rasmus Villemoes
7ddea75654 spi: use is_power_of_2 instead of hweight32 in spi_nor_write()
hweight32 is a somewhat expensive way to check for power-of-2. Use the
is_power_of_2 helper, which does the standard and cheap idiom
foo&(foo-1)==0.

add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-96 (-96)
Function                                     old     new   delta
spi_nor_write                                388     292     -96

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2020-04-29 01:44:35 +05:30
Álvaro Fernández Rojas
b9ec102bc4 nand: brcmnand: return without disabling clock
Linux Broadcom NAND driver only disabled clock if no childs are initialized.
This section of the code seems to have been accidentally dropped when it was
imported in U-Boot.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2020-04-27 20:29:33 +02:00
Patrick van Gelder
27d706937a ARM: zynq: Fix invalid check on NAND_CMD_NONE.
The end_cmd field in the variables cmd_phase_addr and data_phase_addr
contains the value 0xFF when the end_cmd equals NAND_CMD_NONE. This
should be 0x00.

This is caused by comparing NAND_CMD_NONE (int) with end_cmd (u8).
end_cmd will be promoted by the int value -1 and therefore is not equal
to 0xFF. Solved by casting NAND_CMD_NONE to u8 which will avoid int
promotion.

Signed-off-by: Patrick van Gelder <patrick.vangelder@nl.bosch.com>
Reviewed-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-27 14:21:18 +02:00
Baruch Siach
593f3976be mtd: nand: pxa3xx: fix raw read when last_chunk_size == 0
Commit 6293b0361d ("mtd: nand: pxa3xx: add raw read support") added the
local data_len variable in handle_data_pio() to track read size, but
forgot to update the condition of drain_fifo() call. That happens to
work when the layout last_chunk_size != 0. But when last_chunk_size ==
0, drain_fifo() is not called to read the last chunk, which leads to
"Wait timeout!!!" error. Fix this.

Fixes: 6293b0361d ("mtd: nand: pxa3xx: add raw read support")
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2020-04-24 15:17:14 -04:00
Michal Simek
3811746ed9 nand: raw: zynq: Do not try to probe driver if nand flash is disabled
There is no reason to continue when DT status property indicates that NAND
flash is disabled. But that means that NOR flash should be present that's
why try it find it out.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-04-06 12:52:15 +02:00
Michal Simek
36f1f3b640 nand: raw: Do not free xnand structure
xnand structure is private data structure and it is handled by core and
probe shouldn't touch it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-04-06 12:52:05 +02:00
Tom Warren
808e19362f mtd: spi: Add Macronix MX25U3235F device
Add Macronix MX25U3235F flash device description.
This is a 4MiB part.

Signed-off-by: Tom Warren <twarren@nvidia.com>
2020-04-02 14:30:02 -07:00
T Karthik Reddy
4c2c28a465 mtd: nand: Fix on-die ecc issues in arasan_nfc driver
Fixed wrong enumeration of nand_config structure. Added chip select
function before reading the nand chip for maf/dev id's, without this
unable to access id's from some of the micron chips. Also added a
print statement to identify if a nand flash is using on-die ecc.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-02-28 12:04:10 +01:00
Masahiro Yamada
9d86b89c59 dma-mapping: move dma_map_(un)single() to <linux/dma-mapping.h>
The implementation of dma_map_single() and dma_unmap_single() is
exactly the same for all the architectures that support them.

Factor them out to <linux/dma-mapping.h>, and make all drivers to
include <linux/dma-mapping.h> instead of <asm/dma-mapping.h>.

If we need to differentiate them for some architectures, we can
move the generic definitions to <asm-generic/dma-mapping.h>.

Add some comments to the helpers. The concept is quite similar to
the DMA-API of Linux kernel. Drivers are agnostic about what is
going on behind the scene. Just call dma_map_single() before the
DMA, and dma_unmap_single() after it.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-02-19 21:27:30 +08:00
Masahiro Yamada
950c596867 dma-mapping: fix the prototype of dma_unmap_single()
dma_unmap_single() takes the dma address, not virtual address.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-02-19 21:27:30 +08:00
Simon Glass
336d4615f8 dm: core: Create a new header file for 'compat' features
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.

Move the compatibility features into a separate header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-02-05 19:33:46 -07:00
Simon Glass
61b29b8268 dm: core: Require users of devres to include the header
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
2020-02-05 19:33:46 -07:00
Simon Glass
8d38a8459b mtd: Rename free() to rfree()
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-02-05 19:33:46 -07:00
Masahiro Yamada
407b01b3b3 mtd: rawnand: denali_dt: use UCLASS_MTD instead of UCLASS_MISC
UCLASS_MTD is a better fit for NAND drivers.

Make NAND_DENALI_DT depend on DM_MTD, which is needed to compile
drivers/mtd/mtd-uclass.c

Also, make ARCH_UNIPHIER select DM_MTD because all the defconfig
of this platform enables NAND_DENALI_DT.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
2020-02-01 01:14:32 +09:00
Masahiro Yamada
80924cc164 mtd: rawnand: denali: set SPARE_AREA_SKIP_BYTES based on DT compatible
Currently, the denali NAND driver in U-Boot configures the
SPARE_AREA_SKIP_BYTES based on the CONFIG option.

Recently, Linux kernel merged a patch that associates the proper
value for this register with the DT compatible string.

Do likewise in U-Boot too.

The denali_spl.c still uses CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-02-01 01:14:32 +09:00
Masahiro Yamada
21d4a3ca54 mtd: rawnand: denali_dt: insert udelay() after reset deassert
When the reset signal is de-asserted, the HW-controlled bootstrap
starts running unless it is disabled in the SoC integration.
It issues some commands to detect a NAND chip, and sets up registers
automatically. Until this process finishes, software should avoid
any register access.

Without this delay function, some of UniPhier boards hangs up while
executing nand_scan_ident(). (denali_read_byte() is blocked)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-02-01 01:14:32 +09:00
Marek Vasut
9925df051a mtd: rawnand: denali: Do not reset the block before booting the kernel
The Denali NAND driver in mainline Linux currently cannot deassert the
reset. The upcoming Linux 5.6 will support the reset controlling, and
also set up SPARE_AREA_SKIP_BYTES correctly. So, the Denali driver in
the future kernel will work without relying on any bootloader or firmware.
However, we still need to take care of stable kernel versions for a while.
U-boot should not assert the reset of this controller.

Fixes: ed784ac382 ("mtd: rawnand: denali: add reset handling")
Signed-off-by: Marek Vasut <marex@denx.de>
[yamada.masahiro: reword the commit description]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-02-01 01:14:32 +09:00
Masahiro Yamada
11bcc5841a mtd: rawnand: denali_dt: make the core clock optional
The "nand_x" and "ecc" clocks are currently optional. Make the core
clock optional in the same way. This will allow platforms with no clock
driver support to use this driver.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Marek Vasut <marex@denx.de> # On SoCFPGA Arria V
2020-02-01 01:14:32 +09:00
Marek Vasut
33672c970b mtd: rawnand: denali-spl: Add missing hardware init on SoCFPGA
On Altera SoCFPGA, upon either cold-boot or power-on reset, the
Denali NAND IP is initialized by the BootROM ; upon warm-reset,
the Denali NAND IP is NOT initialized by BootROM. In fact, upon
warm-reset, the SoCFPGA BootROM checks whether the SPL image in
on-chip RAM is valid and if so, completely skips re-loading the
SPL from the boot media.

This does sometimes lead to problems where the software left
the boot media in inconsistent state before warm-reset, and
because the BootROM does not reset the boot media, the boot
media is left in this inconsistent state, often until another
component attempts to access the boot media and fails with an
difficult to debug failure. To mitigate this problem, the SPL
on Altera SoCFPGA always resets all the IPs on the SoC early
on boot.

This results in a couple of register values, pre-programmed by
the BootROM, to be lost during this reset. To restore correct
operation of the IP on SoCFPGA, these values must be programmed
back into the controller by the driver. Note that on other SoCs
which do not use the HW-controlled bootstrap, more registers
may have to be programmed.

This also aligns the SPL behavior with the full Denali NAND
driver, which sets these values in denali_hw_init().

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-02-01 01:14:32 +09:00
Vignesh Raghavendra
658df8bd94 mtd: spi-nor-core: Add octal mode support
Add support for Octal flash devices. Octal flash devices use 8 IO lines
for data transfer. Currently only 1-1-8 Octal Read mode is supported.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-27 22:27:22 +05:30
Robert Marko
370d33bc8c mtd: spinand: winbond: Add support for W25N01GV
Linux has supported W25N01GV for a long time, so lets import it.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-27 22:27:22 +05:30
Vignesh Raghavendra
6fff562baf mtd: denali: Drop custom dma mapping functions
Drop local dma_map_single() and dma_unmap_single() and use arch specific
common implementation

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-01-25 12:04:36 -05:00
Philippe Reynes
1453301122 nand: brcmnand: add bcm68360 support
This adds the nand support for chipset bcm68360.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2020-01-23 07:29:58 -05:00
Simon Glass
db41d65a97 common: Move hang() to the same header as panic()
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-17 17:53:40 -05:00
Ashok Reddy Soma
2507ecf18b zynq: mtd: nand: Remove hardcoded base addresses
Remove hardcoded base addresses of smc controller and nand controller.
Get those addresses from dt and replace wherever they are used.
Remove smc and nand base address from header file too.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14 09:05:54 +01:00
Ashok Reddy Soma
45397a6ea3 zynq: mtd: nand: Move zynq nand driver to driver model
Move the zynq nand driver to driver model. Select DM_MTD if
zynq nand controller (NAND_ZYNQ) is selected.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14 09:05:54 +01:00
Ashok Reddy Soma
3dd0f8cccd mtd: nand: Remove hardcoded base address of nand
Remove hardcoded base address of nand and replace it with the
value taken from device tree. Remove base address from header
file too.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14 09:05:52 +01:00
Ashok Reddy Soma
b014b833bd mtd: nand: Move arasan nand driver to driver model
Make changes to arasan nand driver to move it to driver model.
Select DM_MTD if arasan nand driver is selected.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14 09:05:52 +01:00
Tom Rini
ac0f978afd First set of u-boot-atmel features for 2020.04 cycle
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJeFDfVAAoJEB6zHgIOrC/IKfsH/2cUfXuc9IgA7L90L3g7htlS
 zLAQSC8Xk0WbgbmBJh/lq6zFWj2Mu2yfkZqRzwN8bHkmOPq40F+pEAszVtjH77HM
 FpSjMSDVWfNXuhmoiS571dehA0TGi1b2kknrAXqpOwVuMRncMCwaPi8yZYZSGlSV
 VzMtguQxD0sZg4oMZVde3tCd41smPTPNDjzLZnXdLa0b09+EtW6enGuk3vzXlS/8
 QUT68wUzkeoptJhf3pQ3BXNvkFwdNdYJ74uevDmkAYtvxyl10WNykcwYmH50Q9qq
 9plF11EizmTHlj16rWpZLx66RP0s4pziKaeGMr6S8uln33Cr9N496wPqtuDBnvA=
 =FYPj
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-atmel-2020.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel

First set of u-boot-atmel features for 2020.04 cycle

This feature set is a patch series from Tudor Ambarus which includes
parsing of the spi flash SFDP parser for SST flashes, and using those
tables to retrieve unique saved per device MAC address. This is then
used as base mac address on the SAMA5D2 Wireless SOM EK board.
2020-01-07 08:44:56 -05:00
Tom Rini
5a8fa095cb Merge branch 'next'
Bring in the following merges:

commit 8fbbec12f7
Merge: 87f69f467a 63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date:   Fri Jan 3 09:48:47 2020 -0500

    Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next

    - updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support

commit 87f69f467a
Merge: c0912f9bbf 4466b99703
Author: Tom Rini <trini@konsulko.com>
Date:   Tue Dec 24 08:18:19 2019 -0500

    Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next

    - Enable DM driver on ppc/km boards
    - Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
      T104x, P4080, P2041, P2020, P1020, P3041
    - Some updates in mpc85xx-ddr driver, km boards

commit c0912f9bbf
Merge: 533c9f5714 a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date:   Wed Dec 18 07:20:19 2019 -0500

    Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next

    - Various x86 common codes updated for TPL/SPL
    - I2C designware driver updated for PCI
    - ICH SPI driver updated to support Apollo Lake
    - Add Intel FSP2 base support
    - Intel Apollo Lake platform specific drivers support
    - Add a new board Google Chromebook Coral

commit 533c9f5714
Merge: 553cb06887 033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date:   Tue Dec 17 07:53:08 2019 -0500

    Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next

    i2c: for next
    - misc: i2c_eeprom:
      Add partition support and add ability to query size
      of eeprom device and partitions
    - i2c common:
      add support for offset overflow in to address and add
      sandbox tests for it.

commit 553cb06887
Merge: f39abbbc53 b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date:   Thu Dec 12 08:18:59 2019 -0500

    Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next

    buildman improvements including toolchain environment feature
    sandbox unicode support in serial
2020-01-06 17:07:49 -05:00
Vignesh Raghavendra
cb56caacf8 mtd: spi-nor-core: Fix static checker warnings
Static checker warns 'ret' variable may be used uninitialized in
spi_nor_erase() and spi_nor_write() in case of zero length requests.
Fix these warnings by checking for zero length requests and returning
early.

Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2019-12-27 17:47:26 +05:30
Peter Robinson
864d66431a mtd: spi-nor: ids: Add GigaDevice gd25q128
Add gd25q128 128Mbit chip to spi-nor id table.

Tested on Pinebook Pro

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-12-18 20:05:40 +05:30
Tudor Ambarus
a11c081da3 mtd: spi: spi-nor-core: Add SST vendor specific SFDP parser
JESD216 allow vendors to define their own SFDP tables.

Add SST SFDP parser. The vendor table is allocated using resource-managed
kmalloc - the table will be freed on driver detach. It will be accessible
by getting the UCLASS_SPI_FLASH's private data.

The SST's SFDP table is particularly of interest because contains
pre-programmed globally unique EUI-48 and EUI-64 identifiers.

Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
2019-12-17 09:49:05 +02:00
Simon Glass
4806fcea1a mtd: spi: Export spi_flash_std_probe()
With of-platdata we need to create drivers for particular chips, or at
least drivers that are separate from the standard code, since C structures
are created by dtoc which are private to that driver.

To avoid duplicating the probing code, export this probe function for use
by these drivers.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-12-15 11:44:24 +08:00
Miquel Raynal
fb4384490d mtd: Makefile: deep cleanup
Move MTD-related lines out of the root Makefile. Put them in their
respective directories. Enclose some of these new lines to skip them
when building the SPL. MTD core files and some MTD device drivers are
compiled in a mtd.o object and included in the final object only if
MTD support is required (there are two different symbols for that, one
for U-Boot and one for the SPL).

Now that all defconfigs have been fixed, we can stop the logic where
enabling a command selects the core files to compile. This logic is
broken since selecting a symbol with a 'depends on' will not enforce
this secondary dependency.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-12-04 17:10:51 -05:00
Miquel Raynal
eb446ef625 cmd: nand/sf: isolate legacy code
The 'sf' command is not supposed to rely on the MTD stack, but both
'sf' and 'nand' commands use helpers located in mtd_uboot.c. Despite
their location, these functions do not depend at all on the MTD
stack.

This file (drivers/mtd/mtd_uboot.c) is only compiled if CONFIG_MTD is
selected, which is inconsistent with the current situation. Solve this
by moving these three functions (which are only used by the above two
commands) out of mtd_uboot.c and put them in a C file only compiled
with cmd/sf.c and cmd/nand.c.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Don't export get_part function now]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04 17:10:51 -05:00
Miquel Raynal
85f7e9d547 mtd: spi: SPI_FLASH_MTD depends on MTD
It is already the case that all defconfigs with SPI_FLASH_MTD also
declare using MTD, but let's make this consistent and enforce it in
Kconfig. Most of the time SPI_FLASH_MTD is used in conjunction with
UBI, which already depends on MTD.

Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-12-04 17:10:51 -05:00
Miquel Raynal
c8f555f102 mtd: nand: add includes in NAND core to avoid warnings
Because of the include's game, when some files are compiled for a SPI
NAND device, no warning appears. But when it is for a raw NAND device,
GCC complains. Fix these warning by including <common.h>.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-04 17:10:51 -05:00
Miquel Raynal
888f184abe mtd: rename CONFIG_MTD_DEVICE -> CONFIG_MTD
Like in Linux, just use CONFIG_MTD to compile the MTD stack.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-03 23:04:10 -05:00
Miquel Raynal
1de770d544 mtd: rename CONFIG_MTD -> CONFIG_DM_MTD
CONFIG_MTD must be reserved for the MTD core. Like any other
subsystem, prefix the symbol by DM when it comes to DM support.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Add Kconfig files]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03 23:04:10 -05:00
Miquel Raynal
88718be300 mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND
Add more clarity by changing the Kconfig entry name.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-03 23:04:10 -05:00
Tom Rini
56e5a39346 mtd: mtdcore: Drop unused mtd_table
The array 'mtd_table' is unused in the code.  Remove this as gcc doesn't
always discard unused global variables.

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03 08:43:24 -05:00
Simon Glass
cb3ef6810a common: Move old EEPROM functions into a new header
These functions do not use driver model but are still used. Move them to a
new eeprom.h header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:25:25 -05:00
Simon Glass
288b29e44d common: Move command functions out of common.h
Move these functions into the command.h header file which is a better fit.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:25:02 -05:00
Simon Glass
36bf446b64 common: Move enable/disable_interrupts out of common.h
Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:25:01 -05:00
Simon Glass
c30b7adbca common: Move interrupt functions into a new header
These functions do not use driver model but are fairly widely used in
U-Boot. But it is not clear that they will use driver model anytime soon,
so we don't want to label them as 'legacy'.

Move them to a new irq_func.h header file. Avoid the name 'irq.h' since it
is widely used in U-Boot already.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:25:00 -05:00
Simon Glass
1eb69ae498 common: Move ARM cache operations out of common.h
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:24:58 -05:00
Simon Glass
3db7110857 crc32: Use the crc.h header for crc functions
Drop inclusion of crc.h in common.h and use the correct header directly
instead.

With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:08 -05:00
Igor Opaniuk
9ab5f221a5 nand: mxs_nand: add API for switching different BCH layouts
On i.MX7 in a sake of reducing the disturbances caused by a neighboring
cells in the FCB page in the NAND chip, a randomizer is enabled when
reading the FCB page by ROM bootloader.

Add API for setting BCH to specific layout (and restoring it back) used by
ROM bootloader to be able to burn it in a proper way to NAND using
nandbcb command.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-11-03 21:49:19 +01:00
Tom Rini
412326d1bc Merge tag 'u-boot-clk-23Oct2019' of https://gitlab.denx.de/u-boot/custodians/u-boot-clk
- Add I2C clocks for i.MX6Q CCF driver
- Fix check in clk_set_default_parents()
- Managed API to get clock from device tree
- Fixes for core clock code (including sandbox regression tests)
2019-10-30 13:13:46 -04:00
Tom Rini
cc64810dc6 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-sunxi
- H6 dts(i) sync (Clément)
- H6 PIO (Icenowy)
- Fix pll1 clock calculation (Stefan)
- H6 dram, half DQ (Jernej)
- A64 OLinuXino eMMC (Sunil)
2019-10-30 09:04:52 -04:00
William Zhang
e365de9051 drivers: nand: brcmnand: fix nand_chip ecc layout structure
The current brcmnand driver is based on 4.18 linux kernel which uses
mtd_set_ooblayout to set ecc layout. But nand base code in u-boot is from
old kernel which does not use this new API and expect nand_chip.ecc.layout
structure to be set. This cause nand_scan_tail function running into a bug
check if the device has a different oob size than the default ones.

This patch ports the brcmstb_choose_ecc_layout function from kernel 4.6.7
that supports the ecc layout struture and replaces the mtd_set_ooblayout
method

Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-10-25 17:20:43 +02:00
Álvaro Fernández Rojas
a9f80cf9ad nand: brcm: add BCM6368 support
This adds support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-10-25 17:20:43 +02:00
Fabio Estevam
395ec74186 spi-nor-ids: Add support for Adesto AT25SL321
Add an entry for the Adesto AT25SL321 SPI NOR chip.

This SPI NOR chip is found in the Embedded Artist i.MX7ULP COM board.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 00:48:32 +05:30
Frieder Schrempf
832ce20278 mtd: spi: Clean up usage of CONFIG_SPI_FLASH_MTD
Most boards currently use SPI_FLASH_MTD only in U-Boot proper, not in
SPL. They often rely on hacks in the board header files to include
this option conditionally. To be able to fix this, we previously
introduced a separate option SPL_SPI_FLASH_MTD.

Therefore we can now adjust the Makefile and change the code in
sf_probe.c and sf_internal.h to use CONFIG_IS_ENABLED(SPI_FLASH_MTD).

We also need to move all occurences of CONFIG_SPI_FLASH_MTD from the
header files to the according defconfigs. The affected boards are
socfpga, aristainetos, cm_fx6, display5, ventana, rcar-gen2, dh_imx6
and da850evm.

We do this all in one patch to guarantee bisectibility.

This change was tested with buildman to make sure it does not
introduce any regressions by comparing the resulting binary sizes.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 00:48:32 +05:30
Vignesh Raghavendra
73d74b5881 spi-nor: spi-nor-ids: Add USE_FSR flag for mt25q* and n25q* entry
n25q* and mt25q* (both 256Mb and 512Mb) flashes support Flag status
register that indicates various errors that may be encountered during
erase/write operations. Therefore add USE_FSR flag wherever missing.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 00:48:32 +05:30
Vignesh Raghavendra
8651593a8c spi-nor: spi-nor-ids: Add entries for mt25q variants
mt25q* flashes support stateless 4 byte addressing opcodes. Add entries
for the same. These flashes have bit 6 set in 5th byte of READ ID
response when compared to n25q* variants.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 00:48:32 +05:30
Vignesh Raghavendra
d66e07cdf9 spi-nor: spi-nor-ids: Disable SPI_NOR_4B_OPCODES for n25q512* and n25q256*
Per datasheets of n25q256* and n25q512* not all variants of n25q256* and
n25q512* support 4 Byte stateless addressing opcodes. Therefore drop
SPI_NOR_4B_OPCODES flag from these entries

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 00:48:32 +05:30
Vignesh Raghavendra
2a2174d3da mtd: spi-nor-core: Replace MTD_SPI_NOR_USE_4K_SECTORS with SPI_FLASH_USE_4K_SECTORS
U-Boot uses CONFIG_SPI_FLASH_USE_4K_SECTORS to enable 4K small sector
support. Use that instead of MTD_SPI_NOR_USE_4K_SECTORS.

Reported-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 00:48:32 +05:30
Vignesh Raghavendra
cc9118757f mtd: spi-nor-core: Use dev_err for reporting erase/write failures
Use dev_err() when reporting reason for erase/write failures so that
users can be made aware of the reason for failure.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 00:48:32 +05:30
Frieder Schrempf
64f736c901 mtd: spi: Add a new option SPL_SPI_FLASH_MTD to Kconfig
To allow SPI_FLASH_MTD being enabled separately in SPL we add a new
option. The only user currently is the stm32mp15_basic board.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 00:48:31 +05:30
Jagan Teki
77df1a9b66 mtd: spi: Kconfig: Imply SPI_FLASH if DM_SPI_FLASH
DM_SPI_FLASH should require spi flash interface code for dm
version, so imply SPI_FLASH core by default if any board
enabled DM_SPI_FLASH.

This overcome the explicit enablement of CONFIG_SPI_FLASH on
respective boards when DM_SPI_FLASH being used.

Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 00:48:31 +05:30
Jagan Teki
97009d543d mtd: spi-nor: ids: Add is25wp256 chip
Add is25wp256, chip to spi-nor id table.

Tested on SiFive FU540 board.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-25 00:48:31 +05:30
Jagan Teki
989fd97fe5 mtd: spi: Kconfig: Update CONFIG_SPI_FLASH
1) CONFIG_SPI_FLASH is not just a legacy code, but it has common
   core code which handle both dm and non-dm spi flash code. So
   fix the info text to make it clear globally.

2) Since it's flash core it shouldn't depends on legacy SPI,
   so remove the 'depends on SPI'

Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 00:42:57 +05:30
Vignesh Raghavendra
c2dfd0a4d8 mtd: Add TI HyperBus Memory Controller driver
AM654/J721e has HyperBus Memory Controller that supports HyperFlash and
HyperRAM devices. It provides a memory mapped interface to interact with
these devices. Add a driver to support the same.
Driver calibrates the controller, setups up for MMIO access and probes
HyperFlash child node.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2019-10-24 09:49:10 +02:00
Vignesh Raghavendra
d75eacf9b8 mtd: cfi_flash: Use CONFIG_SYS_MONITOR_BASE only when defined
Make use of CONFIG_SYS_MONITOR_BASE only when available to avoid build
error when CONFIG_SYS_MONITOR_BASE is not defined.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2019-10-24 09:48:53 +02:00
Jean-Jacques Hiblot
52720c536f drivers: clk: Add a managed API to get clocks from the device-tree
Add devm_clk_get(), devm_clk_get_optional() to get clocks from the
device-tree. The clocks is automatically released and the data structure
freed when the device is unbound.
Also add devm_clk_put() to release the clock and free the data structure
manually.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-22 16:14:05 +02:00
Stefan Roese
524acec47c ubi: Print skip_check in ubi_dump_vol_info()
It might be interesting, if "skip_check" is set or not, so lets print
this flag in ubi_dump_vol_info() as well.

hs: fix typo in commit message

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
2019-10-16 05:42:27 +02:00
Quentin Schulz
386f20cade ubi: provide a way to skip CRC checks
Some users of static UBI volumes implement their own integrity check,
thus making the volume CRC check done at open time useless. For
instance, this is the case when one use the ubiblock + dm-verity +
squashfs combination, where dm-verity already checks integrity of the
block device but this time at the block granularity instead of verifying
the whole volume.

Skipping this test drastically improves the boot-time.

Adapted to U-Boot by Stefan Roese.

Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
2019-10-16 05:42:27 +02:00
Simon Glass
27084c03d3 spl: Allow tiny printf() to be controlled in SPL and TPL
At present there is only one control for this and it is used for both SPL
and TPL. But SPL might have a lot more space than TPL so the extra cost of
a full printf() might be acceptable.

Split the option into two, providing separate SPL and TPL controls. The
TPL setting defaults to the same as SPL.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-08 13:57:45 +08:00
Eugeniy Paltsev
718fd834c0 mtd: spi-nor: enable protection ops for SST26 flash series
Commit c4e8862308 (mtd: spi: Switch to new SPI NOR framework)
performs switch from previous 'spi_flash' infrastructure without
proper testing/investigations which results in a regressions for
SST26 flash series.

Enable protection ops for SST26 flash series which were
previously enabled by
Commit 3d4fed87a5 (mtd: sf: Add support of sst26wf* flash ICs
protection ops)

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-09-16 08:09:22 +05:30
Eugeniy Paltsev
e0cacdcc0a mtd: spi-nor: add missing SST26* flash IC protection ops
Commit c4e8862308 (mtd: spi: Switch to new SPI NOR framework)
performs switch from previous 'spi_flash' infrastructure without
proper testing/investigations which results in a regressions for
SST26 flash series.

Add missing SST26* flash IC protection ops which were introduced
previously by
Commit 3d4fed87a5 (mtd: sf: Add support of sst26wf* flash ICs
protection ops)

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-09-16 08:09:22 +05:30
Jagan Teki
210d8ad0fa mtd: spi: Drop sf.c
spi_write_then_read, will manage to do the respective
spi_xfer based on the tx_buf, rx_buf so drop the
legacy spi_flash_read/write/cm code.

Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-09-16 08:09:22 +05:30
Jagan Teki
43084a56b0 mtd: spi_dataflash: Use spi read then write
Now, we have spi_write_then_read routine that would handle
spi_xfer handling based on the tx_buf and rx_buf parameters.

So, replace individual flash read/write/cmd transfer call
with spi_write_then_read.

Cc: Egnite GmbH <info@egnite.de>
Cc: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
Cc: Ilko Iliev <iliev@ronetix.at>
Cc: Marek Vasut <marex@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Alison Wang <alison.wang@nxp.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-09-16 08:09:22 +05:30
Stefan Roese
c680df7e84 mtd: nand: raw: Move CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig
Convert CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig, update defconfigs,
headers and whitelist.

Please note that this symbol already was used in Kconfig
(imply in CONFIG_NAND_ATMEL) which did not work, since this symbol was
not available in Kconfig. This changes now with this patch and all
boards with CONFIG_NAND_ATMEL will have BBT enabled. Which is what
I also need on my GARDENA AT91SAM based board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
[trini: Rework such that the configs are unchanged to start with]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-25 20:58:37 -04:00
Simon Glass
f3998fdc4d env: Rename environment.h to env_internal.h
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.

Rename this file and add a comment at the top to indicate its internal
nature.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-11 19:27:31 -04:00
Simon Glass
e7dcf5645f env: Drop environment.h header file where not needed
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11 16:43:41 -04:00
Simon Glass
3a7d55716d env: Move env_get_f() to env.h
Move this function over to the new header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-08-11 16:43:41 -04:00
Heinrich Schuchardt
51443f57d8 nand: davinci: avoid out of bounds array access
The array bounds have to be checked before accessing the array element.

Identified by cppcheck.

Fixes: 67ac6ffaee ("mtd: nand: davinci: add opportunity to write keystone U-boot image")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-07-31 13:08:07 -04:00
Bartosz Golaszewski
29d8eb3345 nand: davinci: add support for driver model
Extend the davinci NAND driver to support the driver model. For now this
doesn't add any device-tree parsing due to the fact that we can't access
the actual nand node on the device-tree - it's a subnode of the aemif
device and we don't have an aemif driver on davinci at the moment.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-07-29 17:58:52 -04:00
Bartosz Golaszewski
7bf9972643 nand: davinci: make davinci_nand_init() static
This function is only used within the driver itself. No need
to export it.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-07-29 17:58:52 -04:00
Tom Rini
df9a7a195b u-boot-imx-20190719
- CCF for i.MX6
 - nandbcb command to write SPL into NAND
 - Switch to DM (i.MX28)
 - Boards: Toradex, engicam, DH
 - Fixes for i.MX8
 - Fixes for i.MX7ULP
 
 Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/561147504
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAl0y6dgPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3iDYL/AgznVr7kSHoYpSGfBp8pH3R1UdUiQFg437+
 9/wqMJM5Txm1aK7qTW2u5I7qzIpGw0LMPZ7CDQhWJa1Z0hdNWf/1lMzCVOPvCl1v
 C0TK5hx3ufyfgpkGdkPvVXTmn0f8tdiqtS8zQOLVntPe5dIuOySS0MbD9K4Xewfm
 sVYO0p6F1q+EHbRGw33kIX3/ST8wuj7Iki0AFiZ2hAImHO7UeZP2X3k31kbhs+ZB
 /uhUit3Rn0nc5sIqiiP6Ptfjp8eq13LwWbSwJzezCQssmkTn14z6rrgwUcNuXNlh
 Vi88kJr2ObkFgwUpQCWss+sHzyJQkTX/iLz52FCWB4Ruzr6zGr/4ONLT/iDP0Ydl
 ncO3v8uqLpAeB7kdkt8JRJhq62qihdZc6mdN2YJoCYUZSlR3gxzKmXvT+drglsOi
 B78KoU/MgQ10REQ9IoTRLhQc1gwTF8LJSyfz5hjRGoMhD/Ek5WAQJaMlxDg67Ai8
 HB4lUNjkCV58HdP1+zIWJbbxrDc/lg==
 =LNOs
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20190719' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20190719

- CCF for i.MX6
- nandbcb command to write SPL into NAND
- Switch to DM (i.MX28)
- Boards: Toradex, engicam, DH
- Fixes for i.MX8
- Fixes for i.MX7ULP

Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/561147504
2019-07-27 09:35:05 -04:00
Ashish Kumar
9454fee460 mtd: spi: Add micron mt35xu512aba and mt35xu02g flash ID
mt35xu512aba and mt35xu02g suports Single I/O and OCTAL I/O
also enable use of SPI_NOR_4B_OPCODES.

These flashes are tested on LX2160ARDB and LS1028ARDB respectively

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
[jagan: suffix 'ba' on part name and update commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-22 16:57:23 +05:30
Shyam Saini
1d43e24b94 i.MX6: nand: add nandbcb command for imx
Writing/updating boot image in nand device is not
straight forward in i.MX6 platform and it requires
boot control block(BCB) to be configured.

It becomes difficult to use uboot 'nand' command to
write BCB since it requires platform specific attributes
need to be taken care of.

It is even difficult to use existing msx-nand.c driver by
incorporating BCB attributes like mxs_dma_desc does
because it requires change in mtd and nand command.

So, cmd_nandbcb implemented in arch/arm/mach-imx

BCB contains two data structures, Firmware Configuration Block(FCB)
and Discovered Bad Block Table(DBBT). FCB has nand timings,
DBBT search area, page address of firmware.

On summary, nandbcb update will
- erase the entire partition
- create BCB by creating 2 FCB/DBBT block followed by
  1 FW block based on partition size and erasesize.
- fill FCB/DBBT structures
- write FW/SPL on FW1
- write FCB/DBBT in first 2 blocks

for nand boot, up on reset bootrom look for FCB structure in
first block's if FCB found the nand timings are loaded for
further reads. once FCB read done, DTTB will load and finally
firmware will be loaded which is boot image.

Refer section "NAND Boot" from doc/imx/common/imx6.txt for more usage
information.

Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
2019-07-19 14:51:25 +02:00
Ashish Kumar
8385520f29 mtd: spi: Add flash property for Micron mt25qu512a
mt25qu512a is rebranded after its spinoff from STM, so it is
different only in term of extended jedec ID, initial JEDEC id
is same as that of n25q512a.In order to avoid any confussion
with respect to name new entry is added.

This flash is tested for Single I/O mode on LS1046FRWY although
it also support QUAD I/O.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-18 17:11:16 +05:30
Patrick Delaunay
d99ea13cdf mtd: rawnand: stm32_fmc2: avoid warnings when building with W=1 option
This patch solves warnings detected by setting W=1 when building.

Warnings type detected:
 - [-Wsign-compare]
 - [-Wtype-limits]

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12 11:50:57 +02:00
Markus Klotzbuecher
a2257d378e ubispl: introduce separate CONFIG_UBI_SPL_SILENCE_MSG
This allows to silence ubi and ubispl individually.

Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
2019-07-09 07:00:26 +02:00
Hamish Guthrie
6ea31cce0b ubispl: add support for loading volumes by name
The motivation is to use the UBI atomic volume rename functionality to
allow double copy software updates on UBI. To that end the SPL is
configured to always load the same volume name (e.g. "u-boot"),
whereas a software updater always installs into the secondary volume
"u-boot_r". After successful installation, these two volume names are
switched.

This extension is protected by #ifdefs as it will somewhat slow down
loading of volumes by id. This is because the code needs to disable
the optimization of ignoring all volume ids which are not
to-be-loaded, since these can only be resolved after attaching.

This adds two vtbl related functions from Linux, which are taken from
the same kernel version as the current main U-Boot UBI code (Linux 4.2
64291f7db5bd8).

Signed-off-by: Hamish Guthrie <hamish.guthrie@kistler.com>
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
2019-07-09 07:00:25 +02:00
Markus Klotzbuecher
5ebd3df64d ubi: fix UBI_SILENCE_MSG
- drop CONFIG_ prefix from kconfig entry
 - fix small compilation issue with CONFIG_UBI_SILENCE_MSG

Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
2019-07-09 07:00:23 +02:00
Patrice Chotard
e6b7afe737 mtd: Fix get_mtdparts()
When ENV_IS_IN_UBI is enable, get_mtdparts is called before relocation.

During first get_mtdparts() call, mtdparts is not available in environment,
it can be retrieved by calling board_mtdparts_default(), but following
env_set() do nothing as we are before relocation. Finally mtdparts is
still not available in environment.

At second get_mtdparts() call, use_defaults is false, but mtdparts is still
not in environment and is NULL.

Remove use_defaults bool, only mtdparts criteria is useful.

Fixes: commit 5ffcd50612 ("mtd: Use default mtdparts/mtids when not defined
in the environment")

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06 17:40:14 +02:00
Mario Six
fe7d654d04 mpc83xx: Migrate CONFIG_SYS_{BR, OR}*_PRELIM to Kconfig
Migrate the BR/OR settings to Kconfig. These must be known at compile
time, so cannot be configured via DT.

Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-21 07:52:33 +02:00
Trevor Woerner
1001502545 CONFIG_SPL_SYS_[DI]CACHE_OFF: add
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.

Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-18 08:15:35 -04:00
Chris Packham
661bbc50d3 mtd: ubi: Remove select for non existent option
There is no 'config CRC32' remove the select that was attempting to use
it.

Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2019-05-10 07:18:13 -04:00
Tom Rini
8b77ea90a7 Merge branch 'master' of git://git.denx.de/u-boot-spi
- Important spi-mem fix
2019-05-06 07:18:28 -04:00
Bartosz Golaszewski
a7fc3d7c68 nand: davinci: remove dead code for dm644x
The support for DaVinci DM* SoCs has been dropped. The code that used
to be relevant to dm644x is no longer needed. Remove it.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-05-04 13:04:07 -04:00
Weijie Gao
60e2bf4678 mtd: spi-nor: fix page program issue when using spi-mem driver
Some SPI controllers can't write nor->page_size bytes in a single step
because their TX FIFO is too small, but when that happens we should
make sure a WRITE_EN command before each write access and READ_SR command
after each write access is issued.

We should allow nor->write() to return a size that is smaller than the
requested write size to gracefully handle this case.

Also, the spi_nor_write_data() should return the actual number of bytes
that were written during the spi_mem_exec_op() operation.

This patch is a combination of two commits backported from kernel:

  commit 630d6bd8a3b4 ("mtd: spi-nor: Support controllers with limit ...")
  commit 3baa8ec88c2f ("mtd: devices: m25p80: Make sure WRITE_EN is ...")

Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Acked-by: Vignesh R <vigneshr@ti.com>
Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com> # microzed
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2019-05-03 15:26:12 +05:30
Gregory CLEMENT
5f626e7849 mtd: nand: raw: Fix CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT behavior
The purpose of "mtd: nand: raw: allow to disable unneeded ECC layouts"
was to allow disabling the default ECC layouts if a driver is known to
provide its own ECC layout. However, this commit did the opposite and
disabled the default layout when it was _not_ selected.

It breaks all the NAND drivers not providing their own ECC layout this
patch fix this situation.

It was tested with the lpc32xx_nand_slc driver.

Fixes: a38c3af868 ("mtd: nand: raw: allow to disable unneeded ECC layouts")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-04-26 18:58:20 -04:00
Philippe Reynes
f917438772 drivers: nand: brcmnand: add an option to read the write-protect from device tree
The option write-protect may only change on the kernel command line,
we add a property in the device tree to be more flexible.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-22 11:55:58 -04:00
Philippe Reynes
317d40eb01 drivers: nand: brcmnand: add parameter parameter-page-big-endian
The parameter page isn't always in big endian, so we add
an option to choose the endiannes of the parameter page.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-22 11:55:58 -04:00
Philippe Reynes
22daafba25 drivers: nand: brcmnand: add initial support
The driver brcmnand come from linux kernel 4.18.
Only SoC bcm6838 and bcm6858 are supported.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-22 11:55:58 -04:00
Boris Brezillon
9db29b300f mtd: nand: provide several helpers to do common NAND operations
Linux commit 97d90da8a88 ("mtd: nand: provide several helpers
to do common NAND operations")

This is part of the process of removing direct calls to ->cmdfunc()
outside of the core in order to introduce a better interface to execute
NAND operations.

Here we provide several helpers and make use of them to remove all
direct calls to ->cmdfunc(). This way, we can easily modify those
helpers to make use of the new ->exec_op() interface when available.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[miquel.raynal@free-electrons.com: rebased and fixed some conflicts]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[Philippe Reynes: adapt code to u-boot and only keep new function]

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-22 11:55:58 -04:00
Simon Goldschmidt
ed784ac382 mtd: rawnand: denali: add reset handling
This adds reset handling to the devicetree-enabled Denali NAND driver.

For backwards compatibility, only a warning is printed when failing to
get reset handles.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-04-17 22:20:16 +02:00
Tom Rini
216800acf1 Merge branch 'master' of git://git.denx.de/u-boot-spi
Conflicts:
	arch/arm/dts/armada-385-amc.dts
	arch/arm/dts/armada-xp-theadorable.dts
	arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-14 00:03:06 -04:00
Christophe Kerello
7bb75023a7 mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver
The driver adds the support for the STMicroelectronics FMC2 NAND
Controller found on STM32MP SOCs.

This patch adds the polling mode, a basic mode that do not need
any DMA channels.

Only NAND_ECC_HW mode is actually supported.
The driver supports a maximum 8k page size.
The following ECC strength and step size are currently supported:
 - nand-ecc-strength = <8>, nand-ecc-step-size = <512> (BCH8)
 - nand-ecc-strength = <4>, nand-ecc-step-size = <512> (BCH4)
 - nand-ecc-strength = <1>, nand-ecc-step-size = <512> (Extended ECC
   based on Hamming)

This patch has been tested on Micron MT29F8G08ABACAH4.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
2019-04-12 16:09:13 +02:00
Neil Armstrong
30b9a28a3f mtd: spi-nor-ids: Add Gigadevice gd25lq128 ID
This adds support for the Gigadevice gd25lq128 ID needed on the
upcoming libretech-ac board.

SPI_NOR_QUAD_READ is not set since it has not been tested in Quad
mode.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-12 18:41:33 +05:30
Patrick Delaunay
b0cc1b846f dm: spi: Read default speed and mode values from DT
This patch update the behavior introduced by
commit 96907c0fe5 ("dm: spi: Read default speed and mode values from DT")

In case of DT boot, don't read default speed and mode for SPI from
CONFIG_* but instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.

Remove also use in boards of the value speed=0 (no more supported)
for ENV in SPI by using CONFIG_ENV_SPI_MAX_HZ=0.

DT values will be always used when available (full DM support of
SPI slave with available DT node) even if speed and mode are requested;
for example in splash screen support (in splash_sf_read_raw)
or in SPL boot (in spl_spi_load_image).
The caller of spi_get_bus_and_cs() no more need to force speed=0.

But the current behavior don't change if the SPI slave is not
present (device with generic driver is created automatically)
or if platdata is used (CONFIG_OF_PLATDATA).

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-12 11:54:50 +05:30
Marek Vasut
f909ddb3e1 mtd: spi: Replace ad-hoc default implementation with spi_mem_op
Replace the ad-hoc erase operation implementation with a simple spi_mem_op
implementation of the same functionality. This is a minor optimization and
removal of the ad-hoc code.

This however also changes the behavior of the execution of the erase
opcode from two separate transfer requests to the SPI NOR driver to
one transfer request to the SPI NOR driver. The former was how U-Boot
behaved before the SPI NOR framework was imported and the later was
introduced by the SPI NOR framework. The former is more optimal, so
keep that.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Vignesh R <vigneshr@ti.com>
Tested-by: Ashish Kumar <Ashish.kumar@nxp.com>
2019-04-12 11:42:48 +05:30
Miquel Raynal
3f3aef4b9d mtd: fix Coverity integer handling issue
A Coverity robot reported an integer handling issue
(OVERFLOW_BEFORE_WIDEN) in the potentially overflowing expression:

    (mtd_div_by_ws(mtd->size, mtd) - mtd_div_by_ws(offs, mtd)) *
    mtd_oobavail(mtd, ops)

While such overflow will certainly never happen due to the numbers
handled, it is cleaner to fix this operation anyway.

The problem is that all the maths include 32-bit quantities, while the
result is stored in an explicit 64-bit value.

As maxooblen will just be compared with a size_t, let's change the
type of the variable to a size_t. This will not fix anything but will
clarify a bit the situation. Then, do an explicit cast to fix Coverity
warning.

Addresses-Coverity-ID: 184180 ("Integer handling issues")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-04-12 10:59:17 +05:30
Marek Vasut
3d2f12c4a1 mtd: spi: Add Macronix MX66U2G45F device
Add Macronix MX66U2G45F flash device description.
This is a 256 MiB part.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Vignesh R <vigneshr@ti.com>
[jagan: use 'g' instead of 'f' in flash name]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-12 10:56:25 +05:30
Neil Armstrong
cd35365762 mtd: sf_probe: remove spi-flash compatible
Now the "spi-flash" compatible has been removed in the DTS files,
remove this compatible from sf_probe to finally use the Linux "jedec,spi-nor"
compatible.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-04-12 10:54:27 +05:30
Heiko Schocher
a2dc8b1832 mtd: add spi flash id s25fl064l
Add support for SPANSION s25fl064l

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Vignesh R <vigneshr@ti.com>
2019-04-12 10:54:27 +05:30
Stefan Roese
d67fb265d1 mtd: spinand: Sync GigaDevice GD5F1GQ4UExxG with latest Linux version
This patch sync's the U-Boot SPI NAND GigaDevice GD5F1GQ4UExxG support
with the latest Linux version (v5.0-rc3) plus the chip supported posted
on the MTD list. Only the currently in U-Boot available chip is
supported with this sync.

The changes for the GD5F1GQ4UExxG are:
- Name of NAND device changed to better reflect the real part
- OOB layout changed to only reserve 1 byte for BBT
- Use ECC caps 8bits/512bytes instead of 8bits/2048bytes
- Enhanced ecc_get_status() function to determine and report
  a more fine grained bit error status

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2019-04-12 10:54:11 +05:30
Eran Matityahu
734b080e78 mtd: ubi, ubifs debug: Use pr_debug instead of pr_crit
Before printk.h was introduced and MTDDEBUG was removed,
pr_crit() was calling MTDDEBUG(), which was since then
replaced by the current pr_debug().

pr_debug is more appropriate here.

Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2019-04-09 07:46:42 +02:00
Eran Matityahu
66e78fc196 mtd: ubi debug: Remove the pid print from ubi_assert
Add a new definition for ubi_assert and keep
the original one in an ifndef __UBOOT__.

Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2019-04-09 07:46:31 +02:00
Patrick Delaunay
14453fbfad Convert CONFIG_SF_DEFAULT_* to Kconfig
This converts the following to Kconfig:
  CONFIG_SF_DEFAULT_BUS
  CONFIG_SF_DEFAULT_CS
  CONFIG_SF_DEFAULT_MODE
  CONFIG_SF_DEFAULT_SPEED

I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25 17:36:53 -04:00
Adam Ford
d46d27d3b6 MTD: mxs_nand_spl: Redo the way nand_init initializes
Currently the spl system calls nand_init which does nothing.
It isn't until an attempt to load from NAND that it gets initialized.
Subsequent attempts to load just skip the initialization  because
NAND is already initialized.

This moves the contents of mxs_nand_init to nand_init.  In the event
of an error, it clears the number of nand chips found.  Any
attempts to use nand will check if there are nand chips available
instead of actually doing the initialization at that time. If there
are none, it will return an error to the higher level calls.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-03-13 09:14:35 +01:00
Adam Ford
04568bd0b6 MTD: nand: mxs_nand: Allow driver to auto setup ECC in SPL
The initialization of the NAND in SPL hard-coded ecc.bytes,
ecc.size, and ecc.strength which may work for some NAND parts,
but it not appropriate for others.  With the pending patch
"mxs_nand: Fix BCH read timeout error on boards requiring ECC"
the driver can auto configure the ECC when these entries are
blank.  This patch has been tested in NAND flash with oob 64
and oob 128.

Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15 12:42:13 +01:00
Adam Ford
5645df9e00 MTD: NAND: mxs_nand_init_dma: Make mxs_nand_init_dma static
mxs_nand_init_dma is only referenced from mxs_nand.c.  It's not
referenced in any headers or outside code, so this patch
defines it as static.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-02-15 12:36:44 +01:00
Adam Ford
5ae585ba3a MTD: mxs_nand: Fix BCH read timeout error on boards requiring ECC
The LogicPD board uses a Micron Flash with ECC.  To boot this from
SPL, the ECC needs to be correctly configured or the BCH engine
times out.

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15 12:36:08 +01:00
Vignesh R
778572d7cb mtd: spi: Add lightweight SPI flash stack for SPL
Add a tiny SPI flash stack that just supports reading data/images from
SPI flash. This is useful for boards that have SPL size constraints and
would need to use SPI flash framework just to read images/data from
flash. There is approximately 1.5 to 2KB savings with this.

Based on prior work of reducing spi flash id table by
Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Vignesh R
5b66fdb29d mtd: spi: Remove unused files
spi_flash and spi_flash_ids are no longer needed after SPI NOR
migration. Remove them.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Vignesh R
c4e8862308 mtd: spi: Switch to new SPI NOR framework
Switch spi_flash_* interfaces to call into new SPI NOR framework via MTD
layer. Fix up sf_dataflash to work in legacy way. And update sandbox to
use new interfaces/definitions

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Vignesh R
2ee6705be0 mtd: spi: sf_probe: Add "jedec, spi-nor" compatible string
Linux uses "jedec,spi-nor" as compatible string for JEDEC compatible
SPI Flash device nodes. Therefore make U-Boot also to look for the same
compatible string so that we can use Linux DTS files as is.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Vignesh R
8c927809ea mtd: spi: spi-nor-core: Add back U-Boot specific features
For legacy reasons, we will have to keep around U-Boot specific
SPI_FLASH_BAR and SPI_TX_BYTE. Add them back to the new framework

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Vignesh R
0c6f187cdb mtd: spi: spi-nor-core: Add SFDP support
Sync Serial Flash Discoverable Parameters (SFDP) parsing support from
Linux. This allows auto detection and configuration of Flash parameters.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Vignesh R
61059bc55a mtd: spi: spi-nor-core: Add 4 Byte addressing support
Sync changes from Linux SPI NOR framework to add 4 byte addressing
support. This is required in order to support flashes like MT35x
that no longer support legacy Bank Address Register(BAR) way of accessing
>16MB region.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Vignesh R
492e65b29b mtd: spi: spi-nor-core: Add SPI MEM support
Many SPI controllers have special MMIO interfaces which provide
accelerated read/write access but require knowledge of flash parameters
to make use of it. Recent spi-mem layer provides a way to support such
controllers.
Therefore, add spi-mem support to spi-nor-core as a way to support SPI
controllers with MMIO interface. SPI MEM layer takes care of translating
spi_mem_ops to spi_xfer()s in case of legacy SPI controllers.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Vignesh R
7aeedac015 mtd: spi: Port SPI NOR framework from Linux
Current U-Boot SPI NOR support (sf layer) is quite outdated as it does not
support 4 byte addressing opcodes, SFDP table parsing and different types of
quad mode enable sequences. Many newer flashes no longer support BANK
registers used by sf layer to a access >16MB of flash address space.
So, sync SPI NOR framework from Linux v4.19 that supports all the
above features. Start with basic sync up that brings in basic framework
subsequent commits will bring in more features.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Adam Ford
96d0be07e7 MTD: nand: mxs_nand_spl: Fix empty function pointer for BBT
The initialization function calls a nand_chip.scan_bbt(mtd) but
scan_bbt is never initialized resulting in an undefined function
pointer.  This will direct the function pointer to nand_default_bbt
defined in the same file.

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
2019-01-28 20:55:46 +01:00
T Karthik Reddy
97fca6a146 mtd: nand: arasan_nfc: Add support for nand multi chip select
This patch adds support for nand multi chip select.
Also adding CONFIG_SYS_NAND_MAX_CHIPS to Kconfig to specify maximum number
of nand chips.

Signed-off-by: Tummala Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24 10:03:42 +01:00
Derald D. Woods
49ad40298c ARM: at91: Convert SPL_GENERATE_ATMEL_PMECC_HEADER to Kconfig
This commit converts the following items to Kconfig:

CONFIG_ATMEL_NAND_HWECC
CONFIG_ATMEL_NAND_HW_PMECC
CONFIG_PMECC_CAP
CONFIG_PMECC_SECTOR_SIZE
CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER

[PMECC References]
https://www.at91.com/linux4sam/bin/view/Linux4SAM/PmeccConfigure
https://www.at91.com/linux4sam/bin/view/Linux4SAM/AT91Bootstrap

[Mailing List Thread]
https://lists.denx.de/pipermail/u-boot/2018-December/350666.html

Fixes: 5541543f ("configs: at91: Remove CONFIG_SYS_EXTRA_OPTIONS assignment")
[trini: Make the migration be size neutral and possibly not fix the
above in all cases]
Reported-by: Daniel Evans <photonthunder@gmail.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-21 08:36:11 -05:00
Stefan Agner
a38c3af868 mtd: nand: raw: allow to disable unneeded ECC layouts
Each ECC layout consumes about 2984 bytes in the .data section. Allow
to disable the default ECC layouts if a driver is known to provide its
own ECC layout.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-01-16 16:14:45 -05:00
Tom Rini
695f67b5b3 Merge branch 'master' of git://git.denx.de/u-boot-spi 2019-01-02 14:20:29 -05:00
Nikolai Zhubr
cdf72c188c mtd: nand: raw: Add Hynix H27UBG8T2BTR id table
This patch adds Hynix H27UBG8T2BTR id table as part of raw nand,
these chips were available in some A20-olinuxino-micro boards.

Signed-off-by: Nikolai Zhubr <n-a-zhubr@yandex.ru>
[jagan: add proper commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-02 00:58:16 +05:30
Tom Rini
522e035441 imx for 2019.01
- introduce support for i.MX8M
 - fix size limit for Vhybrid / pico boards
 - several board fixes
 - w1 driver for MX2x / MX5x
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAlwrbc8PHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3oCwL/RCqesqQaLKkUQDiYQJzoa6Ia7TeSTD1HoHl
 lYXarE9FloD7lHp4Lz1elU8Y+yTtjvixKS9UJGRc0pMcJJ/CEavjK+oBOVNbEnvH
 vm/oXQfZqj60tLc2Z7RfRe1gHHCcaGiBXJePea5WhP89cUZW1YBs4TVY2AIEQeRV
 V8vcxbBprqqBWyFRgH+ORsWrmkfcYEfiMr97Y8v07RRPX/C80e98PTc16fh9o7S1
 +i8Pcs0SIMnA8PqXVgrpa4DT7OS/ZtLADG/ODpvJ25nHoKvdhlXMc8o8L5dyaO1f
 66UD0A8D3PXkXkFodZujSjtKl5ygeA/4YkEnY6PRqd2W6kZsq6R7XCu/3e3eQSwK
 GFnWQnzLkDOCKMZlxR8l3sJdhY3Ee3oAQ+EX3PEy1MvKKrGA8PSOIKHq3tVNrPYB
 tBnJP32G+2Ya0SG169ROoUMZQQXfTt+9kdqsxx5xL2Pfpt9d+YinCM8uQdhqBGPa
 COqegLaD0ZkADsodZp876u3Irbo6bw==
 =mEcH
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20190101' of git://www.denx.de/git/u-boot-imx

imx for 2019.01

- introduce support for i.MX8M
- fix size limit for Vhybrid / pico boards
- several board fixes
- w1 driver for MX2x / MX5x
2019-01-01 10:01:00 -05:00
Lukasz Majewski
acdf10e179 nand: vybrid: Extend the vf610 NFC NAND driver to support device tree (and DM)
This commit adds support for device tree and enumeration via device model
for the Vybrid's NFC NAND driver.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-01-01 14:12:18 +01:00
Lukasz Majewski
8a12d127d7 Kconfig: Add entry for VF610 NAND NFC device tree aware driver
This commit provides code to add proper entry to Kconfig to enable
support for VF610 device tree aware driver.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-01-01 14:12:18 +01:00
Lukasz Majewski
254409dbe8 nand: vybrid: Use calloc() instead of malloc() to allocate struct nfc
Without this change it is possible that Vybrid's NFC driver malloc() call
will obtain some memory used (and correctly free'd) by some previous
driver (in this case pinctrl for Vybrid).

As a result some fields of struct nfc - in out case mtd->_get_device - are
"pre initialized" with some random values.

On the latter stage of booting, when e.g. somebody calls 'mtdparts default'
the "data abort" is observed when __get_mtd_device() function is called.

The mtd->_get_device pointer is not NULL and wrong value is referenced.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
2019-01-01 14:12:18 +01:00
Masahiro Yamada
9d43649a77 mtd: rawnand: denali: fix a race condition when DMA is kicked
Based on Linux commit cf51e4b9c34407bf0c3d9b582b7837e047e1df47

Add the register read-back, commenting why this is necessary.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-29 11:38:37 +09:00
Masahiro Yamada
8ccfbfb3e1 mtd: rawnand: denali: optimize timing parameters for data interface
Based on Linux commit 1dfac31a5a63ac04a9b5fbc3f5105a586560f191

This commit improves the ->setup_data_interface() hook.

The denali_setup_data_interface() needs the frequency of clk_x
and the ratio of clk_x / clk.

The latter is currently hardcoded in the driver, like this:

  #define DENALI_CLK_X_MULT       6

The IP datasheet requires that clk_x / clk be 4, 5, or 6.  I just
chose 6 because it is the most defensive value, but it is not optimal.
By getting the clock rate of both "clk" and "clk_x", the driver can
compute the timing values more precisely.

To not break the existing platforms, the fallback value, 50 MHz is
provided.  It is true for all upstreamed platforms.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-29 11:38:37 +09:00
Masahiro Yamada
a13fe7afe9 mtd: rawnand: denali_dt: add more clocks based on IP datasheet
Based on Linux commit 6f1fe97bec349a1fd6c5a8c7c5998d759fe721d5

Currently, denali_dt.c requires a single anonymous clock, but
the Denali User's Guide requires three clocks for this IP:

 - clk: controller core clock

 - clk_x: bus interface clock

 - ecc_clk: clock at which ECC circuitry is run

This commit supports these named clocks to represent the real hardware.

For the backward compatibility, the driver still accepts a single clock
just as before.  The clk_x_rate is taken from the clock driver again if
the named clock "clk_x" is available.  This will happen only for future
DT, hence the existing DT files are not affected.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-29 11:38:36 +09:00
Tom Rini
9450ab2ba8 Merge branch 'master' of git://git.denx.de/u-boot-spi
- Various MTD fixes from Boris
- Zap various unused / legacy paths.
- pxa3xx NAND update from Miquel

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-12-05 15:06:24 -05:00
Boris Brezillon
08898e8b22 mtd: sf: Make sf_mtd.c more robust
SPI flash based MTD devs can be registered/unregistered at any time
through the sf probe command or the spi_flash_free() function.

This commit does not try to fix the root cause as it would probably
require rewriting most of the code and have an mtd_info object
instance per spi_flash object (not to mention that the the spi-flash
layer is likely to be replaced by a spi-nor layer ported from Linux).

Instead, we try to be as safe as can be by checking the code returned
by del_mtd_device() and complain loudly when there's nothing we can
do about the deregistration failure. When that happens we also reset
sf_mtd_info.priv to NULL, and check for NULL pointer in the mtd hooks
so that -ENODEV is returned instead of hitting a NULL pointer
dereference exception when the MTD instance is later accessed by a user.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
2018-12-06 00:45:36 +05:30
Boris Brezillon
7371944a71 mtd: sf: Unregister the MTD device prior to removing the spi_flash obj
The DM implementation of spi_flash_free() does not unregister the MTD
device before removing the spi dev object. This leads to a use-after-free
bug when the MTD device is later accessed by a MTD user (observed when
attaching the device to UBI after env_sf_load() has called
spi_flash_free()).

Implement ->remove() and call spi_flash_mtd_unregister() from there.

Fixes: 9fe6d8716e ("mtd, spi: Add MTD layer driver")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-12-06 00:45:36 +05:30
Boris Brezillon
4a5594fa20 mtd: Don't stop MTD partition creation when it fails on one device
MTD partition creation code is a bit tricky. It tries to figure out
when things have changed (either MTD dev list or mtdparts/mtdids vars)
and when that happens it first deletes all the partitions that had been
previously created and then creates the new ones based on the new
mtdparts/mtdids values.
But before deleting the old partitions, it ensures that none of the
currently registered parts are being used and bails out when that's
not the case. So, we end up in a situation where, if at least one MTD
dev has one of its partitions used by someone (UBI for instance), the
partitions update logic no longer works for other devs.

Rework the code to relax the logic and allow updates of MTD parts on
devices that are not being used (we still refuse to updates parts on
devices who have at least one of their partitions used by someone).

Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
2018-12-06 00:45:36 +05:30
Boris Brezillon
2428d9160b mtd: Make sure we don't parse MTD partitions belonging to another dev
The mtdparts variable might contain partition definitions for several
MTD devices. Each partition layout is separated by a ';', so let's
make sure we don't pick a wrong name when mtdparts is malformed.

Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
2018-12-06 00:45:36 +05:30
Boris Brezillon
772aa97993 mtd: Make sure the name passed in mtdparts fits in mtd_name[]
The local mtd_name[] variable is limited in size. Return an error if
the name passed in mtdparts does not fit in this local var.

Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
2018-12-06 00:45:36 +05:30
Boris Brezillon
429e048e41 mtd: Be more strict on the "mtdparts=" prefix check
strstr() does not guarantee that the string we're searching for is
placed at the beginning. Use strncmp() instead.

Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
2018-12-06 00:45:36 +05:30
Boris Brezillon
96b06434e5 mtd: Use get_mtdids() instead of env_get("mtdids") in mtd_search_alternate_name()
The environment is not guaranteed to contain a valid mtdids variable
when called from mtd_search_alternate_name(). Call get_mtdids() instead
of env_get("mtdids").

Fixes: ff4afa8a98 ("mtd: uboot: search for an equivalent MTD name with the mtdids")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
2018-12-06 00:45:36 +05:30
Boris Brezillon
492151b209 mtd: sf: Make sure we don't register the same device twice
spi_flash_mtd_register() can be called several times and each time it
will register the same mtd_info instance like if it was a new one.
The MTD ID allocation gets crazy when that happens, so let's track the
status of the sf_mtd_info object to avoid that.

Fixes: 9fe6d8716e ("mtd, spi: Add MTD layer driver")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-12-06 00:45:36 +05:30
Boris Brezillon
a02820fca9 mtd: Delete partitions attached to the device when a device is deleted
If we don't do that, partitions might still be exposed while the
underlying device is gone.

Fixes: 2a74930da5 ("mtd: mtdpart: implement proper partition handling")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
2018-12-06 00:45:36 +05:30
Boris Brezillon
779c9c0565 mtd: Parse mtdparts/mtdids again when the MTD list has been updated
Updates to the MTD device list should trigger a new parsing of the
mtdids/mtdparts vars even if those vars haven't changed.

Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
2018-12-06 00:45:36 +05:30
Boris Brezillon
4c47fd0b6b mtd: Add a function to report when the MTD dev list has been updated
We need to parse mtdparts/mtids again everytime a device has been
added/removed from the MTD list, but there's currently no way to know
when such an update has been done.

Add an ->updated field to the idr struct that we set to true every time
a device is added/removed and expose a function returning the value
of this field and resetting it to false.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
2018-12-06 00:45:36 +05:30
Martin Lund
1cefca71d2 mtd: nand: Arasan: Add subpage configuration support
Add support for disabling subpage write support via
CONFIG_SYS_NAND_NO_SUBPAGE_WRITE.

Currently the Linux Arasan driver does not support subpage writes and in
case of running UBI and accessing the same UBI volume from both U-Boot
and Linux it is required to have the same subpage write configuration
else the location of the UBI headers (EC + VID) will be misaligned
(subpage vs page) and incompatible. Hence the need for disabling
subpage write support in the U-Boot Arasan NAND driver.

Signed-off-by: Martin Lund <malu@gomspace.com>
Acked-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-26 10:50:54 +01:00
Miquel Raynal
c907464a0a mtd: rawnand: pxa3xx: fix 2kiB pages with 8b strength chips layout
The initial layout for such NAND chips was the following:

+----------------------------------------------------------------------------+
| 1024 (data) | 30 (ECC) | 1024 (data) | 30 (ECC) | 32 (free OOB) | 30 (ECC) |
+----------------------------------------------------------------------------+

This layout has a weakness: reading empty pages trigger ECC errors
(this is expected), but the hardware ECC engine tries to correct the
data anyway and creates itself bitflips, hence bitflips are detected
in erased pages while actually there are none in the NAND chip.

Two solutions have been found at the same time. One was to enlarge the
free OOB area to 64 bytes, changing the layout to be:

+----------------------------------------------------------------------------+
| 1024 (data) | 30 (ECC) | 1024 (data) | 30 (ECC) | 64 (free OOB) | 30 (ECC) |
+----------------------------------------------------------------------------+
                                                    ^^

The very big drawbacks of this solution are:
1/ It prevents booting from NAND.
2/ The current Linux driver (marvell_nand) does not have such problem
because it already re-reads possible empty pages in raw mode before
checking for bitflips. Using different layouts in U-Boot and Linux
would simply not work.

As this driver does support raw reads now and uses it to check for
empty pages, let's forget about this broken hack and return to the
initial layout with only 32 free OOB bytes.

Fixes: ac56a3b30c ("mtd: nand: pxa3xx: add support for 2KB 8-bit flash")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-11-22 11:38:13 +05:30
Miquel Raynal
af61ea27f5 mtd: nand: pxa3xx: re-read a page in raw mode on uncorrectable error
This only applies on BCH path.

When an empty page is read, it triggers an uncorrectable error. While
this is expected, the ECC engine might produce itself bitflips in the
read data under certain layouts. To overcome this situation, always
re-read the entire page in raw mode and check for the whole page to be
empty.

Also report the right number of bitflips if there are any.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-11-22 11:38:05 +05:30
Miquel Raynal
6293b0361d mtd: nand: pxa3xx: add raw read support
Raw read support is added by editing a few code sections:

    ->handle_data_pio() includes the ECC bytes that are not consumed
    anymore by the ECC engine.

    ->prepare_set_command() is changed so that the ECC bytes are
    requested as part of the data I/O length.

    ->drain_fifo() shall also avoid checking the R/B pin too often
    when in raw mode.

    ->read_page_raw()/->read_oob_raw() are written from scratch.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-11-22 11:37:44 +05:30
Simon Glass
a58986ca8b sf: Add a method to obtain the block-protect setting
It is useful to obtain the block-protect setting of the SPI flash, so we
know whether it is fully open or (perhaps partially) write-protected. Add
a method for this. Update the sandbox driver to process this operation and
add a test.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-11-20 19:14:22 -07:00
Vladimir Zapolskiy
44cdfc0ece mtd: nand: lpc32xx slc: disable DMA support in SPL builds
Testing and analysis shows that at the moment LPC32xx NAND SLC driver
can not get PL080 DMA backbone support in SPL build, because SPL NAND
loaders operate with subpage (ECC step to be precisely) reads, and
this is not supported in the NAND SLC + DMA + hardware ECC calculation
bundle.

The change removes a cautious build time warning and explicitly
disables DMA flavour of the driver for SPL builds, to reduce the
amound of #ifdef sections the code blocks are minimally reorganized.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
2018-11-16 13:34:37 -05:00
Vladimir Zapolskiy
a098ce2142 mtd: nand: lpc32xx mlc: predefine number of NAND chips to support
Build option CONFIG_SYS_MAX_NAND_CHIPS is used by NXP LPC32xx NAND MLC
driver only, as a preparation for potential removal or replacement of
the option the change predefines CONFIG_SYS_MAX_NAND_CHIPS to 1, same
value is used by the single user Work Microwave Work 92105 board, thus
it will be safe now to remove the option as a board specific one.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-11-16 13:34:36 -05:00
Boris Brezillon
1f758b7936 mtd: Drop duplicate MTD_PARTITIONS Kconfig option
Commit 9c5b00973b ("Convert CONFIG_MTD_PARTITIONS et al to Kconfig")
introduced a publicly visible Kconfig entry for the
CONFIG_MTD_PARTITIONS option, while the rework on MTD partitioning
was in progress, and we somehow did not notice that the same Kconfig
entry was added by commit 4048a5c519 ("mtd: declare MTD_PARTITIONS
symbol in Kconfig"), but this time as an invisible entry (this can
only be selected by other options).

Keep the non-visible version of this symbol, since MTD_PARTITIONS is
not something the user should be able to enable/disable directly.

Fixes: 4048a5c519 ("mtd: declare MTD_PARTITIONS symbol in Kconfig")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13 18:53:10 +05:30
Boris Brezillon
5ffcd50612 mtd: Use default mtdparts/mtids when not defined in the environment
U-boot provides a mean to define default values for mtdids and mtdparts
when they're not defined in the environment. Patch mtd_probe_devices()
to use those default values when env_get("mtdparts") or
env_get("mtdids") return NULL.

This implementation is based on the logic found in cmd/mtdparts.c.

Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13 18:53:10 +05:30
Bin Meng
ed5df0852f nand: atmel: Initialize pmecc smu with correct size
Currently in pmecc_get_sigma(), the code tries to clear the memory
pointed by smu with wrong size 'sizeof(int16_t) * ARRAY_SIZE(smu)'.
Since smu is actually a pointer, not an array, so ARRAY_SIZE(smu)
does not generate correct size to be cleared.

In fact, GCC 8.1.0 reports a warning against it:

error: division 'sizeof (int16_t * {aka short int *}) / sizeof (int16_t
{aka short int})' does not compute the number of array elements
[-Werror=sizeof-pointer-div]

Fix it by using the correct size.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-10-22 09:18:49 -04:00
Adam Ford
2fe88d4522 Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig
This converts the following to Kconfig:
   CONFIG_FLASH_CFI_DRIVER
   CONFIG_SYS_FLASH_USE_BUFFER_WRITE
   CONFIG_FLASH_CFI_MTD
   CONFIG_SYS_FLASH_PROTECTION
   CONFIG_SYS_FLASH_CFI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-19 19:19:50 -04:00
Tom Rini
e6cd05e502 Merge branch 'master' of git://git.denx.de/u-boot-spi 2018-10-12 11:54:13 -04:00
Ashish Kumar
5c391486b4 sf: Add MICRON manufacturer id
NOR flash name MT35X_QLKA and MT25Q_** used on NXP board has
manufacturer id as 0x2C, which are rather for newer flashes
after the split of Micron from ST.

So macro for this micron manufacturer id.

Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
[jagan: updated commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-10-12 11:37:49 +05:30
Adam Ford
c8602061a7 mtd: uboot: Fix hanging during mtd list command
Some boards (like omap3_logic) hang when trying to access
address 0. This happens when executing the new 'mtd list' command.
This patch enhances the checks for conditions that would
preclude mtd_probe_devices() from operating.

Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-10-10 11:34:10 +05:30
Simon Glass
5e24a2ef8b dm: spi: Add logging of some return values
When SPI flash operations fail it is helpful to be able to see the error
codes and where they are generated. Add logging to capture this
information for read operations.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
97f57109bb sf: Avoid allocating memory on every read operation
At present spi_flash_cmd_read_ops() allocates and frees a few bytes of
memory every time it is called. It is faster to use the stack for this
and this is now supported by the minimum GCC version required by U-Boot.

Remove the allocation and use a variable-sized array instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
66613f5dd2 dm: spi: Clean up detection of sandbox SPI emulator
Now that we don't have to deal with the command-line flag we can simplify
the code for detecting the emulator. Remove the lookup based on the SPI
specification, relying just on the device tree to locate the emulator.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
c3aed5db59 sandbox: spi: Add more logging
Add logging to aid debugging features in these drivers. Also drop some
code in sandbox_spi_xfer() which is not used.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
1289e96797 sandbox: spi: Drop command-line SPI option
At present we support specifying SPI flash devices to use in the device
tree and on the command line. Drop the second option, since it is a pain
to support nicely with driver model, and unnecessary.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:26 -06:00
Stefan Roese
9e5c2a755a mtd: nand: spi: Add Gigadevice SPI NAND support
This patch adds support for Gigadevices SPI NAND device to the new SPI
NAND infrastructure in U-Boot. Currently only the 128MiB GD5F1GQ4UC
device is supported.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Jagan Teki <jagan@openedev.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-10-04 18:24:24 +05:30
Stefan Roese
881e4fc206 sf: Add XMC xm25qh64a and xm25qh128a entries
This patch adds support for 2 new XMC (Wuhan Xinxin Semiconductor
Manufacturing Corp) SPI NOR chips.

This support can be enabled by selecting the SPI_FLASH_XMC Kconfig
option.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-04 18:21:23 +05:30
Miquel Raynal
5db66b3aee cmd: mtd: add 'mtd' command
There should not be a 'nand' command, a 'sf' command and certainly not
a new 'spi-nand' command. Write a 'mtd' command instead to manage all
MTD devices/partitions at once. This should be the preferred way to
access any MTD device.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-10-02 22:12:32 +05:30
Miquel Raynal
2a74930da5 mtd: mtdpart: implement proper partition handling
Instead of collecting partitions in a flat list, create a hierarchy
within the mtd_info structure: use a partitions list to keep track of
the partitions of an MTD device (which might be itself a partition of
another MTD device), a pointer to the parent device (NULL when the MTD
device is the root one, not a partition).

By also saving directly in mtd_info the offset of the partition, we
can get rid of the mtd_part structure.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-10-02 22:12:32 +05:30
Miquel Raynal
ff4afa8a98 mtd: uboot: search for an equivalent MTD name with the mtdids
Using an MTD device (resp. partition) name in mtdparts is simple and
straightforward. However, for a long time already, another name was
given in mtdparts to indicate a device (resp. partition) so the
"mtdids" environment variable was created to do the match.

Let's create a function that, from an MTD device (resp. partition)
name, search for the equivalent name in the "mtdparts" environment
variable thanks to the "mtdids" string.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-10-02 22:12:32 +05:30
Miquel Raynal
21cc1fb5af mtd: mtdpart: add a generic mtdparts-like parser
The current parser is very specific to U-Boot mtdparts implementation.
It does not use MTD structures like mtd_info and mtd_partition. Copy
and adapt the current parser in drivers/mtd/mtd-uclass.c (to not break
the current use of mtdparts.c itself) and write some kind of a wrapper
around the current implementation to allow other commands to benefit
from this parsing in a user-friendly way.

This new function will allocate an mtd_partition array for each
successful call. This array must be freed after use by the caller.
The given 'mtdparts' buffer pointer will be moved forward to the next
MTD device (if any, it will point towards a '\0' character otherwise).

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-10-02 22:12:31 +05:30
Miquel Raynal
e9f62db64b mtd: uclass: add probe function
The user might want to trigger the probe of any MTD device, export these
functions so they can be called from a command source file.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-10-02 22:12:31 +05:30
Miquel Raynal
b0036f7004 mtd: mtdpart: balance debug messages
Balance debug message in the partition allocation/removal process in
order to keep track of them more easily.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-09-20 20:10:49 +05:30
Miquel Raynal
4048a5c519 mtd: declare MTD_PARTITIONS symbol in Kconfig
UBI selects MTD_PARTITIONS which is the symbol to compile
drivers/mtd/mtdpart.c. Unfortunately, the symbol was not defined in
Kconfig and this worked only with board files defining it. Fix this by
adding a boolean in Kconfig so boards defined by defconfig files only
will work as expected.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-09-20 20:10:49 +05:30
Miquel Raynal
515d021261 mtd: spinand: Add initial support for the MX35LF2GE4AB chip
Add support for the MX35LF2GE4AB chip, which is similar to its cousin
MX35LF1GE4AB, with two planes instead of one.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-09-20 20:10:49 +05:30
Boris Brezillon
6f041ccabb mtd: spinand: Add initial support for the MX35LF1GE4AB chip
Add minimal support for the MX35LF1GE4AB SPI NAND chip.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-09-20 20:10:49 +05:30
Frieder Schrempf
3181c0a622 mtd: spinand: Add initial support for Winbond W25M02GV
Add support for the W25M02GV chip.

Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-09-20 20:10:49 +05:30
Peter Pan
883d8778ae mtd: spinand: Add initial support for Micron MT29F2G01ABAGD
Add a basic driver for Micron SPI NANDs. Only one device is supported
right now, but the driver will be extended to support more devices
afterwards.

Signed-off-by: Peter Pan <peterpandong@micron.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-09-20 20:10:49 +05:30
Peter Pan
0a6d6bae03 mtd: nand: Add core infrastructure to support SPI NANDs
Add a SPI NAND framework based on the generic NAND framework and the
spi-mem infrastructure.

In its current state, this framework supports the following features:

- single/dual/quad IO modes
- on-die ECC

Signed-off-by: Peter Pan <peterpandong@micron.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-09-20 20:10:49 +05:30
Boris Brezillon
b95db8d33a mtd: nand: Add core infrastructure to deal with NAND devices
Add an intermediate layer to abstract NAND device interface so that
some logic can be shared between SPI NANDs, parallel/raw NANDs,
OneNANDs, ...

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-09-20 20:10:49 +05:30
Miquel Raynal
3657b2f4a3 mtd: rename nand into rawnand in Kconfig prompt
Sync the Kconfig raw NAND entry title with the code architecture.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-09-20 20:10:49 +05:30
Miquel Raynal
a430fa06a4 mtd: move NAND files into a raw/ subdirectory
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-09-20 20:10:49 +05:30
Miquel Raynal
ce9bdc8743 mtd: move all flash categories inside MTD submenu
There is no reason to have NAND, SPI flashes and UBI sections outside of
the MTD submenu in Kconfig.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-09-20 20:10:49 +05:30
Miquel Raynal
d02f1d36ec mtd: move definitions to enlarge their range
Some helpers might be useful in a future 'mtd' U-Boot command to parse
MTD device list.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-09-20 20:10:49 +05:30
Miquel Raynal
ca040d8512 mtd: Fallback to ->_read/write() when ->_read/write_oob() is missing
Some MTD sublayers/drivers are implementing ->_read/write() and
not ->_read/write_oob().

While for NAND devices both are usually valid, for NOR devices, using
the _oob variant has no real meaning. But, as the MTD layer is supposed
to hide as much as possible the flash complexity to the user, there is
no reason to error out while it is just a matter of rewritting things
internally.

Add a fallback on mtd->_read() (resp. mtd->_write()) when the user calls
mtd_read_oob() (resp. mtd_write_oob()) while mtd->_read_oob() (resp.
mtd->_write_oob) is not implemented. There is already a fallback on the
_oob variant if the former is used.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-09-20 20:10:49 +05:30
Boris Brezillon
8fad769f1e mtd: Add sanity checks in mtd_write/read_oob()
Unlike what's done in mtd_read/write(), there are no checks to make sure
the parameters passed to mtd_read/write_oob() are consistent, which
forces implementers of ->_read/write_oob() to do it, which in turn leads
to code duplication and possibly errors in the logic.

Do general sanity checks, like ops fields consistency and range checking.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Peter Pan <peterpandong@micron.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
[Miquel: squashed the fix about the chip's size check]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-09-20 20:10:49 +05:30
Ezequiel Garcia
5f50d82d89 mtd: Uninline mtd_write_oob and move it to mtdcore.c
There's no reason for having mtd_write_oob inlined in mtd.h header.
Move it to mtdcore.c where it belongs.

Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-09-20 20:10:49 +05:30
Boris Brezillon
596cf083da mtd: Fallback to ->_read/write_oob() when ->_read/write() is missing
Some MTD sublayers/drivers are implementing ->_read/write_oob() and
provide dummy wrappers for their ->_read/write() implementations.
Let the core handle this case instead of duplicating the logic.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-09-20 20:10:49 +05:30
David Sniatkiwicz
e76afd8409 fix: nand: pxa3xx: Add WA for eliminating flash ready timeout
add delay before processing the status flags in pxa3xx_nand_irq().

Signed-off-by: David Sniatkiwicz <davidsn@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
c: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:02:34 +02:00
Konstantin Porotchkin
b7b3f2c8bb nand: pxa3xx: Add support for 8KB page 4 and 8 bit ECC NAND
Add support for NAND chips with 8KB page, 4 and 8 bit ECC (ONFI).

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:02:34 +02:00
Konstantin Porotchkin
e9a0777f85 nand: pxa3xx: cosmetic: add comments to the timing layout structures
Add comments with timing parameter names and some details about
nand layout fileds.
Remove unneeded definition.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:02:34 +02:00
Konstantin Porotchkin
2057eb0b16 fix: nand: Replace hardcoded page chunk size with calculated one
Replace the hardcoded value of page chink with value that
depends on flash page size and ECC strength.
This fixes nand access errors for 2K page flashes with 8-bit ECC.
Move the initial flash commannd function assignment past the ECC
structures initialization for eliminating usage of hardcoded page
chunk size value.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:02:34 +02:00
Konstantin Porotchkin
b0d7c106c9 mtd: nand: pxa3xx: add support for Toshiba flash
Add timings and device ID for Toshiba TC58NVG1S3HTA00 flash

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:02:34 +02:00
Victor Axelrod
ac56a3b30c mtd: nand: pxa3xx: add support for 2KB 8-bit flash
Add support for 2KB page 8-bit ECC strength flash layout

Signed-off-by: Victor Axelrod <victora@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:02:34 +02:00
Boris Brezillon
f3d235702d mtd: nand: pxa3xx: Fix READOOB implementation
In the current driver, OOB bytes are accessed in raw mode, and when a
page access is done with NDCR_SPARE_EN set and NDCR_ECC_EN cleared, the
driver must read the whole spare area (64 bytes in case of a 2k page,
16 bytes for a 512 page). The driver was only reading the free OOB
bytes, which was leaving some unread data in the FIFO and was somehow
leading to a timeout.

We could patch the driver to read ->spare_size + ->ecc_size instead of
just ->spare_size when READOOB is requested, but we'd better make
in-band and OOB accesses consistent.
Since the driver is always accessing in-band data in non-raw mode (with
the ECC engine enabled), we should also access OOB data in this mode.
That's particularly useful when using the BCH engine because in this
mode the free OOB bytes are also ECC protected.

Fixes: 43bcfd2bb24a ("mtd: nand: pxa3xx: Add driver-specific ECC BCH support")
Cc: stable@vger.kernel.org
Reported-by: Sean Nyekjær <sean.nyekjaer@prevas.dk>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:02:34 +02:00
Ofer Heifetz
b47f677931 mtd: nand: pxa3xx_nand: add support for partial chunks
This commit is needed to properly support the 8-bits ECC configuration
with 4KB pages.

When pages larger than 2 KB are used on platforms using the PXA3xx
NAND controller, the reading/programming operations need to be split
in chunks of 2 KBs or less because the controller FIFO is limited to
about 2 KB (i.e a bit more than 2 KB to accommodate OOB data). Due to
this requirement, the data layout on NAND is a bit strange, with ECC
interleaved with data, at the end of each chunk.

When a 4-bits ECC configuration is used with 4 KB pages, the physical
data layout on the NAND looks like this:

| 2048 data | 32 spare | 30 ECC | 2048 data | 32 spare | 30 ECC |

So the data chunks have an equal size, 2080 bytes for each chunk,
which the driver supports properly.

When a 8-bits ECC configuration is used with 4KB pages, the physical
data layout on the NAND looks like this:

| 1024 data | 30 ECC | 1024 data | 30 ECC | 1024 data | 30 ECC | 1024 data | 30 ECC | 64 spare | 30 ECC |

So, the spare area is stored in its own chunk, which has a different
size than the other chunks. Since OOB is not used by UBIFS, the initial
implementation of the driver has chosen to not support reading this
additional "spare" chunk of data.

Unfortunately, Marvell has chosen to store the BBT signature in the
OOB area. Therefore, if the driver doesn't read this spare area, Linux
has no way of finding the BBT. It thinks there is no BBT, and rewrites
one, which U-Boot does not recognize, causing compatibility problems
between the bootloader and the kernel in terms of NAND usage.

To fix this, this commit implements the support for reading a partial
last chunk. This support is currently only useful for the case of 8
bits ECC with 4 KB pages, but it will be useful in the future to
enable other configurations such as 12 bits and 16 bits ECC with 4 KB
pages, or 8 bits ECC with 8 KB pages, etc. All those configurations
have a "last" chunk that doesn't have the same size as the other
chunks.

In order to implement reading of the last chunk, this commit:

 - Adds a number of new fields to the pxa3xx_nand_info to describe how
   many full chunks and how many chunks we have, the size of full
   chunks and partial chunks, both in terms of data area and spare
   area.

 - Fills in the step_chunk_size and step_spare_size variables to
   describe how much data and spare should be read/written for the
   current read/program step.

 - Reworks the state machine to accommodate doing the additional read
   or program step when a last partial chunk is used.

This commit is taken from Linux:
'commit c2cdace755b'
("mtd: nand: pxa3xx_nand: add support for partial chunks")

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:00:39 +02:00
Ofer Heifetz
7efd95eacf mtd: pxa3xx_nand: Simplify pxa3xx_nand_scan
This commit simplifies the initial configuration performed
by pxa3xx_nand_scan. No functionality change is intended.

This commit is taken from Linux:
'commit 154f50fbde53'
("mtd: pxa3xx_nand: Simplify pxa3xx_nand_scan")

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:00:39 +02:00
Ofer Heifetz
b87ae6f587 mtd: pxa3xx_nand: Fix initial controller configuration
The Data Flash Control Register (NDCR) contains two types
of parameters: those that are needed for device identification,
and those that can only be set after device identification.

Therefore, the driver can't set them all at once and instead
needs to configure the first group before nand_scan_ident()
and the second group later.

Let's split pxa3xx_nand_config in two halves, and set the
parameters that depend on the device geometry once this is known.

This commit is taken from Linux:
'commit 66e8e47eae65'
("mtd: pxa3xx_nand: Fix initial controller configuration")

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:00:39 +02:00
Ofer Heifetz
6bbe7f681f mtd: pxa3xx_nand: Increase the initial chunk size
The chunk size represents the size of the data chunks, which
is used by the controllers that allow to split transferred data.

However, the initial chunk size is used in a non-split way,
during device identification. Therefore, it must be large enough
for all the NAND commands issued during device identification.
This includes NAND_CMD_PARAM which was recently changed to
transfer up to 2048 bytes (for the redundant parameter pages).

Thus, the initial chunk size should be 2048 as well.

On Armada 370/XP platforms (NFCv2) booted without the keep-config
devicetree property, this commit fixes a timeout on the NAND_CMD_PARAM
command:

  [..]
  pxa3xx-nand f10d0000.nand: This platform can't do DMA on this device
  pxa3xx-nand f10d0000.nand: Wait time out!!!
  nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x38
  nand: Micron MT29F8G08ABABAWP
  nand: 1024 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224

This commit is taken from Linux:
'commit c7f00c29aa8'
("mtd: pxa3xx_nand: Increase the initial chunk size")

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:00:39 +02:00
Ofer Heifetz
94488612cb nand: pxa3xx: Increase READ_ID buffer and make the size static
The read ID count should be made as large as the maximum READ_ID size,
so there's no need to have dynamic size. This commit sets the hardware
maximum read ID count, which should be more than enough on all cases.
Also, we get rid of the read_id_bytes, and use a macro instead.

This commit is taken from Linux:
'commit b226eca2088'
("nand: pxa3xx: Increase READ_ID buffer and make the size static")

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:00:39 +02:00
Ofer Heifetz
cd11b2b457 mtd: nand: pxa3xx-nand: fix random command timeouts
When 2 commands are submitted in a row, and the second is very quick,
the completion of the second command might never come. This happens
especially if the second command is quick, such as a status read
after an erase

This patch is taken from Linux:
'commit 21fc0ef9652f'
("mtd: nand: pxa3xx-nand: fix random command timeouts")

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:00:39 +02:00
Ofer Heifetz
658999244a mtd: nand: pxa3xx_nand: fix early spurious interrupt
When the nand is first probe, and upon the first command start, the
status bits should be cleared before the interrupts are unmasked.

This commit is taken from Linux:
'commit 0b14392db2e'
("mtd: nand: pxa3xx_nand: fix early spurious interrupt")

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:00:39 +02:00
Ofer Heifetz
d3859d1b53 mtd: nand: pxa3xx_nand: sync pxa3xx_nand_set_sdr_timing()
Since the pxa3xx_nand driver was added there has been a discrepancy in
pxa3xx_nand_set_sdr_timing() around the setting of tWP_min and tRP_min.
This brings us into line with the current Linux code.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:00:39 +02:00
Ofer Heifetz
8cdcf672c5 mtd: nand: pxa3xx_nand: use nand_to_mtd()
Don't store struct mtd_info in struct pxa3xx_nand_host. Instead use the
one that is already part of struct nand_chip. This brings us in line
with current U-boot and Linux conventions.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:00:39 +02:00
Ofer Heifetz
144532242e mtd: nand: pxa3xx_nand: Increase initial buffer size
The initial buffer is used for the initial commands used to detect
a flash device (STATUS, READID and PARAM).

ONFI param page is 256 bytes, and there are three redundant copies
to be read. JEDEC param page is 512 bytes, and there are also three
redundant copies to be read. Hence this buffer should be at least
512 x 3. This commits rounds the buffer size to 2048.

This commit is taken from Linux:
'commit c16340973fcb64614' ("nand: pxa3xx: Increase initial buffer size")

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:00:39 +02:00
Masahiro Yamada
e8f65763ef mtd: nand: denali: fix unaligned cache operations on ARMv7 SoCs
If the OOB size is not multiple of the cache line size, the ARMv7
cache operation still prints "Misaligned operation at range".

=> nand info

Device 0: nand0, sector size 256 KiB
  Page size       4096 b
  OOB size         224 b
  Erase size    262144 b
  subpagesize     4096 b
  options     0x00104200
  bbt options 0x00060000
=> nand dump 0
CACHE: Misaligned operation at range [9fb15280, 9fb16360]
CACHE: Misaligned operation at range [9fb15280, 9fb16360]
CACHE: Misaligned operation at range [9fb15280, 9fb16360]
CACHE: Misaligned operation at range [9fb15280, 9fb16360]
  ...

The cache flushing operations won't happen in this case to cover all of
the range to fix this by making sure we have things aligned.

Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Reword the commit message to be clear this is a direct problem
rather than just a warning]
2018-09-10 14:08:22 -04:00
Tom Rini
b8a1f47be3 Merge git://git.denx.de/u-boot-fsl-qoriq 2018-08-13 12:34:55 -04:00
Darwin Dingel
1711add3dc mtd: nand: fsl_ifc: Fix handling of bitflips in erased pages
This is a fix made for the fsl_ifc_nand driver on linux kernel by
Pavel Machek and is applied to uboot. It is currently on applied on
linux-mtd.

https://patchwork.kernel.org/patch/9758117/

IFC always raises ECC errors on erased pages. It is only ignored when
the buffer is checked for all 0xFF by is_blank(). The problem is a
single bitflip will cause is_blank() and then mtd_read to fail. The fix
makes use of nand_check_erased_ecc_chunk() to check for empty pages
instead of is_blank(). This also makes sure that reads are made at ECC
page size granularity to get a proper bitflip count. If the number of
bitflips does not exceed the ECC strength, the page is considered empty
and the bitflips will be corrected when data is sent to the higher
layers (e.g. ubi).

Signed-off-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Cc: Pavel Machek <pavel@denx.de>
Cc: Scott Wood <oss@buserror.net>
Acked-by: Pavel Machek <pavel@denx.de>
[Kurt: Replaced dev_err by printf due to compiler warnings]
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-08-10 10:35:51 -07:00
Michal Simek
13f451bf56 spi: Kconfig: Create ISSI Kconfig entry
Add ISSI to Kconfig to make it selectable via menuconfig.
Also convert all current platforms.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-08-06 08:44:35 +02:00
Tom Rini
bb694d4e89 Merge branch 'master' of git://git.denx.de/u-boot-spi 2018-08-04 19:41:43 -04:00
Clément Laigle
04d57b1d58 mtd: add spi flash id s25fl128l
Add support for SPANSION s25fl128l

Signed-off-by: Clément Laigle <c.laigle@catie.fr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: fixed , at the end of } ]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-08-03 11:09:53 +05:30
Mylène Josserand
850bdafa50 mtd: nand: sunxi: Return on set_feature only when not ENOTSUPP
Return the error code of the set_features function only if
the error code is not ENOTSUPP. Otherwise, if this function
is not supported, it will return and fail to initialize the
NAND.

Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-07-31 20:45:50 +05:30
Mylène Josserand
cbe9ea26e3 mtd: nand: nand_base: Convert EINVAL into ENOTSUPP
Convert the EINVAL error into ENOTSUPP when the GET/SET_FEATURES
is not supported.

Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-07-31 20:45:42 +05:30
Masahiro Yamada
4a610fada1 mtd: nand: denali: correct buffer alignment for DMA transfer
The NAND framework makes sure to pass in the buffer with at least
chip->buf_align alignment.  Currently, the Denali NAND driver only
requests 16 byte alignment.  This causes unaligned cache operations
for the DMA transfer.

[Error Example]

=> nand read 81000010 0 1000

NAND read: device 0 offset 0x0, size 0x1000
CACHE: Misaligned operation at range [81000010, 81001010]
CACHE: Misaligned operation at range [81000010, 81001010]
CACHE: Misaligned operation at range [81000010, 81001010]
CACHE: Misaligned operation at range [81000010, 81001010]
 4096 bytes read: OK

Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-07-25 08:47:52 +09:00
Tom Rini
f0306a145b Merge branch 'master' of git://git.denx.de/u-boot-imx
trini: Update colibri-imx6ull to use Kconfig for mtdparts related
options.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-07-23 13:37:42 -04:00
Stefan Agner
c7f367bc8d mtd: nand: mxs_nand: add device tree support for i.MX 6
Support i.MX 6 NAND GPMI driver data from device tree.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-07-23 10:12:00 +02:00