This patch adds support for PDMA v2 hardware. The PDMA v2 has extended the
DMA descriptor to 8-words, and some of its fields have changed comparing
to the v1 hardware.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch is a preparation for adding a new version of PDMA of which the
DMA descriptor fields has changed. Using bitfields will result in a complex
modification. Convert bitfields to u32 units can solve this problem easily.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Using a single soc id to control different initialization and TX/RX flow
for all SoCs is not extensible if more hardware variations are added in
the future.
This patch introduces a struct to replace the original mtk_soc to allow
the driver be able handle newer hardwares.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add eMMC and SDXC support for MediaTek MT7981/MT7986 SoCs
Both chips support SDXC and eMMC 4.5. MT7986A supports eMMC 5.1.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds general board files based on MT7981 SoCs.
MT7981 uses one mmc controller for booting from both SD and eMMC, and the
pins of mmc controller are also shared with spi controller.
So three configs are need for these boot types:
1. mt7981_rfb_defconfig - SPI-NOR and SPI-NAND
2. mt7981_emmc_rfb_defconfig - eMMC only
3. mt7981_sd_rfb_defconfig - SD only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add general board files based on MT7986 SoCs.
MT7986 uses one mmc controller for booting from both SD and eMMC.
Both MT7986A and MT7986B use the same pins for spi controller.
Configs for various boot types:
1. mt7986_rfb_defconfig - SPI-NOR and SPI-NAND for MT7986A/B
2. mt7986a_bpir3_emmc_defconfig - eMMC for MT7986A only
3. mt7986a_bpir3_sd_defconfig - SD for MT7986A only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds basic support for MediaTek MT7981 SoC.
This include the file that will initialize the SoC after boot and its
device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds basic support for MediaTek MT7986 SoC.
This include the file that will initialize the SoC after boot and its
device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmMoEdgcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyNvEB/4nEeiBx7Lo1gK+79PJ
9kCUngglHRu3/+FJMpcOp+2b6sSW1IZs8qGBMAMFSRoFElrLMMbVEgBR0ZfJCl3c
It0xN9Buhe8muwtAdE8Amr4PddUEynzglVPpFUFfir6ZqFAcedmN6iuh+K82r7Be
7s/8tRb2hVp//TpkEntf2yxrYnyeW4qiXyUxbUhaUyyhkM3RBXySuY4qnaaLp3NY
R9rsIY5j3kA2QylebEamlXI+KDvszrGbkUOUUrlwkygQNR/GmAYQPlY1TdBwk0wE
U1CO8zQYaL3OY998lU32pMVClmwyXbn2i7KAyMm3TEgrfpjQsLTS2BK+w+RBdMGL
XGnt
=lRvM
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.01 cycle:
This feature set includes the important update on PIO4 pinctrl driver
that solves a long time mismatch between Linux and U-boot, related on
the unification of pinctrl and gpio driver support, now respecting the
pinctrl bindings ABI; and also support for pinctrl subnodes. The feature
set also adds support for PDA screen detection for sam9x60_curiosity
board , one fix for SD-Card reinsertion and one fix for sam9x60 clocks.
With the recent changes in the Orion timer driver Kconfig setup, the
board specific enabling is not needed any more. This patch sync's these
2 boards with their current defconfig version.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Michael Walle <michael@walle.cc>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Adding the "u-boot,dm-pre-reloc" DT property to the timer node is
necesssary to support the timer in the early boot phases (e.g.
SPL & pre-reloc).
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Add the DT bindings / descriptions for timer0 & timer1, exactly as done
in mainline Linux.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
This patch changes the compilation, so that the Armada 375 board(s) are
compiled in a separate step. This is necessary for the timer dts
conversion, as A375 has a different / timer description in the dts.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Now that the new timer support is available for these platforms, let's
select this IF for all these platforms. This way it's not necessary
that each board changes it's config header.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Add timer_get_boot_us() to support boards, that have CONFIG_BOOTSTAGE
enabled, like pogo_v4.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
This patch adds support for other Marvell Armada SoC's, supporting the
25MHz fixed clock operation, like the Armada XP etc.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
With the recent changes in the Marvel mvneta network driver, the MDIO
bus is not connected any more. This patch updates the DT nodes to use
the nodes from the dtsi files instead of creating ad-hoc nodes.
Signed-off-by: Stefan Roese <sr@denx.de>
- Remove EFI support as it's not used on this board
- Disable CONFIG_FIT_PRINT to reduce the serial output (minimal speedup)
Signed-off-by: Stefan Roese <sr@denx.de>
32-bit Marvell Armada BootROMs limit maximal size of SPL image to 192 kB.
So define 192 kB (= 0x30000) limit as default value for SPL_SIZE_LIMIT.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Maximal size of u-boot kwb image binary is $CONFIG_ENV_OFFSET which is
0xF0000 = 983040 bytes. So add missing CONFIG_BOARD_SIZE_LIMIT definition
to ensure that u-boot binary does not overflow to the u-boot env storage.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently CONFIG_BOARD_SIZE_LIMIT check is ignored for u-boot-spl.kwb
target. Fix it by adding missing $(BOARD_SIZE_CHECK) macro.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
commit 970bf8603b ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")
had an unintended side effect of resulting in a bootcmd env var change
for boards like venice that did not have CONFIG_USE_BOOTCOMMAND defined
and relied on it being defaulted in include/config_distro_bootcmd.h.
Following that patch it instead got defaulted in tools/env/fw_env_private.h
Fix this by enabling CONFIG_USE_BOOTCOMMAND for venice.
Fixes: commit 970bf8603b ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
I messed up application of patch 5a428e7510 ("mmc: fsl_esdhc_spl: Add
support for builds without CONFIG_SYS_MMC_U_BOOT_OFFS"). I took it from
a work-in-progress branch where I changed usage of
CONFIG_SDCARD to CONFIG_SD_BOOT
and refactored
SYS_MPC85XX_NO_RESETVEC
mess.
But these changes aren't in master yet. Fix the wrong usage of these
macros.
Fixes: 5a428e7510 ("mmc: fsl_esdhc_spl: Add support for builds without
CONFIG_SYS_MMC_U_BOOT_OFFS")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
Previously, in order for the `pinctrl-*` DT node properties
to be properly processed, the pinctrl's subnodes were limited
to only having the `pinmux` property as well as other additional
properties (slew-rate, bias-disable, etc.). Now, with this patch
the pinctrl driver is made to work similarly to the one from Linux.
It can now distinguish between one subnode and a subnode with multiple
subnodes.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
This has been done in order to align the DT of U-Boot with the DT
of Linux. In Linux, a phandle from a '-gpio' DT property is linked
to the pinctrl driver, a single driver that handles both pinctrl
settings and offers GPIO API to callers. On the other hand,
U-Boot redirects such phandle to a corresponding UCLASS_GPIO
driver, because U-Boot offers two different types of drivers
in this case: UCLASS_PINCTRL which handles pin functions and
UCLASS_GPIO which handles gpio requests as a gpio provider.
Due to this, we have two drivers in Uboot, but the Devicetree
has a single node. Thus, just one of the drivers can be probed
for the DT node during platform initialization, before relocation.
Our previous solution in U-Boot was to have a different devicetree:
the gpio node has a subnode for the pinctrl driver, which
is not compliant with Linux ABI. Furthermore, our documentation
for this type of nodes mentions no such gpio compatible.
After this patch, we can no longer add nodes with a gpio
compatible in the DT. Thus, in order to link the pinctrl driver to
the gpio one, a hook to the bind method of the former in U-Boot has
been added and the GPIO related compatibles have been removed to
avoid conflict when compatibles are enumerated and bound to drivers
during platform start before relocation. The bind method will attach
the GPIO driver to the pinctrl DT node so that every phandle coming
from '-gpio' DT properties will be redirected to a valid driver
attached to the pinctrl DT node.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
This patch makes sure that the Devicetree for the sama7
boards are aligned with the Devicetree from Linux. This
implies removing the GPIO compatible and replacing it
with the PINCTRL one, as well as unifying the SDMMC
pinctrl related subnodes under one single subnode.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
This patch makes sure that the Devicetree for the sama5
boards are aligned with the Devicetree from Linux. This
implies removing the GPIO compatible and replacing it
with the PINCTRL one, as well as unifying the SDMMC
pinctrl related subnodes under one single subnode.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
ddrck and qspick should have mck_div as parent clocks to be in sync with
linux driver.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Call the PDA detection mechanism at boot time so that we can
have the pda environment variable ready for use.
Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
SAM9X60 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol. Enabling one wire and eeprom drivers
for this memory.
Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
Whenever the SD Card would be removed and then re-inserted while in the
U-Boot command line, the `SDBPWR` bit of the `SDMMC_PCR` register would
remain unset afterwards. In order for the bit to be set again after
re-insertion, register an additional `deferred_probe` method that the
DM would then transparently call. This method will call the generic
`sdhci_probe` which will, during its execution flow, set this bit to 1.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reported-by: Mihai Sain <mihai.sain@microchip.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Adjust the DRAM timing settings for this board per ones provided
by hardware department. The change is applied to the LPDDR4 MR11
register CA ODT configuration, from RZQ/6 to RZQ/3, which fixes
stability issues on subset of boards. The DDR PHY PIE block has
been updated accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable GPIO hog support in SPL to match the GPIO hog support in U-Boot proper.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
- integrate bootcount using SNVS_LP general purpose register LPGPR0
- enable link-time optimisation
- explicitly set a boot delay of one second
- enable CRC32 and MD5
- enable command for low-level access to data in a partition
- enable time commands
- enable PMIC commands
- improve ETHPRIME configuration
- enable eMMC HS400 functionality
- enable fixed PHY and MDIO driver model
- remove stale PFUZE100 PMIC driver
- enable thermal management unit driver
- enable more USB host functionality
- enable hexdump
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
"alloc space exhausted" happens in very early stage, which could be seen
with DEBUG_UART options enabled and leeds to an non-functional board.
kontron_pitx_imx8m:
CONFIG_DEBUG_UART_BASE=0x30880000 # for serial3
CONFIG_DEBUG_UART_CLOCK=24000000
imx8mqevk:
CONFIG_DEBUG_UART_BASE=0x30860000 # for uart1
CONFIG_DEBUG_UART_CLOCK=24000000
It is because CONFIG_SYS_MALLOC_F_LEN is too small and still leave
CONFIG_SPL_SYS_MALLOC_F_LEN as 0x2000.
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
only waiting for TXEMPTY leads to corrupted messages going over the
wire - which is fixed by making use of the FIFO
this change is following the linux kernel uart driver
(drivers/tty/serial/imx.c), which also checks UTS_TXFULL
instead of UTS_TXEMPTY
Signed-off-by: Johannes Schneider <johannes.schneider@leica-geosystems.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
on imx8(mm) the RXDMUXSEL needs to be set for data going over the wire
(as observable on a connected 'scope) to actually make it into the
RXFIFO
the reference manual is not overly clear about this, and only
mentiones that "UCR3_RXDMUXSEL should always be set." - and since the
CR3 register reverts to its reset values after setting the baudrate,
setting this bit is done during '_mxc_serial_setbgr'
Signed-off-by: Johannes Schneider <johannes.schneider@leica-geosystems.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Currently, when running ./scripts/get_maintainer.pl on serial_mxc.c
no i.MX maintainer is returned.
Fix it by adding an entry for this driver.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
This code part is broken, remove it.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
This code part is broken, remove it.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
- Annotate boot devices available in spl_board_boot_device().
- Drop SD3_BOOT/MMC3_BOOT not available for boot on Verdin iMX8M Mini.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Prepare for optional job ring driver model. Sec may be initialized based
on the job ring information processed from the device tree.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
