Using set and clear macro is incorrect because it is not overwritting
origin mdc clock division setup.
For example origin setup is 8(0b001) and new setup is 64(0b100) which
means 0b101 is setup which is 96 divider.
Using writel to rewrite all setting like for 1000Mbit/s case.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Zynq has no priority queues.
ZynqMP has one priority queue and this change is required
to get ethernet working.
This patch was not needed on ep108 for uknown reason even
it should be used.
Tested on Zynq and ZynqMP.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Target is duplicating packets. IP prefetches another BD and process it
when the first one is sent. Adding one dummy BD to the chain fix the
problem with packet duplication.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
BD_SEPRN_SPACE should not have hard coded value and it will be
calculated based on the number of buffer descriptors that we
would like to use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Previous loop was completely bogus. Iterration should go just over
statistic counters.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Extend comments with register offset to help with debuggging.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
MII is setup by default for all cases. The most of boards are using
RGMII but PHY drivers are not doing any specific setting that's why MII
setting was working fine. With TI DP83867 is necessary to setup
paramaters based on interface type.
Use one setting per board for it which is something what will be removed
when driver is moved to DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add debug messages to phyread/write to help with PHY debug.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Code is taken from Linux kernel driver (v4.2).
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Change ioremap() to map_physmem(), as it is more used in u-boot.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
-> Add National instrument ethernet transceiver configuration used (DP83848)
-> Change cpsw slave phy address
-> modify nand configuration to use the correct ECC and correct nand features
Fix below warnings happening for xilinx_zynqmp_ep_defconfig
drivers/net/zynq_gem.c: In function ‘zynq_gem_init’:
drivers/net/zynq_gem.c:330:7: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
((u32)(priv->rxbuffers) +
^
In file included from drivers/net/zynq_gem.c:19:0:
drivers/net/zynq_gem.c:336:10: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
writel((u32)priv->rx_bd, ®s->rxqbase);
^
./arch/arm/include/asm/io.h:146:34: note: in definition of macro ‘writel’
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
^
drivers/net/zynq_gem.c: In function ‘zynq_gem_send’:
drivers/net/zynq_gem.c:399:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
writel((u32)priv->tx_bd, ®s->txqbase);
^
./arch/arm/include/asm/io.h:146:34: note: in definition of macro ‘writel’
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
^
drivers/net/zynq_gem.c:404:22: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
priv->tx_bd->addr = (u32)ptr;
^
drivers/net/zynq_gem.c:409:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
addr = (u32) ptr;
^
drivers/net/zynq_gem.c:414:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
addr = (u32)priv->rxbuffers;
^
drivers/net/zynq_gem.c: In function ‘zynq_gem_recv’:
drivers/net/zynq_gem.c:454:31: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
net_process_received_packet((u8 *)addr, frame_len);
^
drivers/net/zynq_gem.c: In function ‘zynq_gem_initialize’:
drivers/net/zynq_gem.c:533:35: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
priv->rx_bd = (struct emac_bd *)((u32)bd_space + BD_SEPRN_SPACE);
^
drivers/net/zynq_gem.c:533:16: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
priv->rx_bd = (struct emac_bd *)((u32)bd_space + BD_SEPRN_SPACE);
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
The Modular Scatter-Gather DMA core is a new DMA core to work
with the Altera Triple-Speed Ethernet MegaCore. It replaces the
legacy Scatter-Gather Direct Memory Access (SG-DMA) controller
core. Please find details on the "Embedded Peripherals IP User
Guide" of Altera.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Add priv ops to prepare msgdma support. These ops are dma type
specific.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Move the sgdma wait from free_pkt to recv. This is the proper
place to wait recv sgdma done.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Get numbers of fdt address and size cells in altera_tse_probe(),
thereby remove the assumption of one address cell and one size
cell.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Replace numerical bit shift with BIT macro
in altera_tse
:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Remove the useless parenthesis.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Chin Liang See <clsee@altera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use data type u32/u16/u8 for regs and desc, as it is more
portable.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Chin Liang See <clsee@altera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Remove unused macro and regs def.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Chin Liang See <clsee@altera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In pch_gbe_probe(), some additional resources are allocated
(eg: mdio, phy). We should free these in the driver remove phase.
Add pch_gbe_remove() to clean it up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In designware_eth_probe(), some additional resources are allocated
(eg: mdio, phy). We should free these in the driver remove phase.
Add designware_eth_remove() to clean it up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
In phy_connect_dev(), if the phy device has an accociated mac device
before, a warning message will be printed. But we should test the
old device against the new one, if they are actually the same one,
don't print the warning message.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In get_phy_device_by_mask(), when no phy is found, currently we only
print a message to show the first phy address that is not found. But
this is not always the case as multiple phys can be specified by
phy_mask. Change to print all phys that are not found, and to reduce
the console boot log, change to use 'debug' instead of 'printf'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In get_phy_device_by_mask(), when no phy is found, we should not
create any phy device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
NAND-tree is used to check wiring between MAC and PHY using NAND gates
on the PHY side, hence the name.
NAND-tree initial status is latched at reset by probing the IRQ pin.
However some devices are sharing the PHY IRQ pin with other peripherals
such as Atmel SAMA5D[34]x-EK boards when using the optional TM7000
display module, therefore they are switching the PHY in NAND-tree test
mode depending on the current IRQ line status at reset.
This patch ensure PHY is not in NAND-tree test mode only for the Micrel
KSZ8051 PHY used by Atmel. There are other Micrel PHY affected but I
doubt they are used on such weird hardware design.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Casting from dev->priv to pci_dev_t changes the value's size on a 64-bit
system. This causes the compiler to complain about casting a pointer to an
integer of a different (smaller) size. To avoid this, cast to an integer
of matching size first, then perform an int->int cast to perform the size
change. This signals explicitly that we do want to change the size, and
avoids the compiler warning. This is legitimate since we know the pointer
actually stores a small integer, not a pointer value.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds support for Micrel KSZ8021RNL & KSZ8031RNL.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
There are two LS series processors are built on ARMv8 Layersacpe
architecture currently, LS2085A and LS1043A. They are based on
ARMv8 core although use different chassis, so create fsl-layerscape
to refactor the common code for the LS series processors which also
paves the way for adding LS1043A platform.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
QSGMII PCS needed to be programmed same as SGMII PCS, and there are
four ports in QSGMII PCS, port 0, 1, 2, 3, all the four ports shared
port 0's MDIO controller, so when programming port 0, we continue to
program other three ports.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The fsl_dtsec.h & fsl_tgec.h & fsl_fman.h can be shared on both ARM
and PPC, move it out of ppc to include/, and change the path in
drivers accordingly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
codes related to phylib operations should be wrapped by CONFIG_PHYLIB.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In convention, the '0' is a normal return value indicating there isn't
an error. While some functions of FMan IM driver treat '0' as an error
return value.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The FMan IM driver is developed for 32-bit platfroms and isn't
friendly to 64-bit platforms, so do the minimal refactor:
1. Refine the MURAM management and access.
2. Correct the initialization and operations for QDs and BDs.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Frame Manager(FMan) is a big-endian peripheral, so the
registers, internal MURAM and BDs, which are allocated in main
memory and used to communication between core and FMan, should
be accessed in big-endian. The big-endian platforms can access
them directly as the code implemented so far, while for the
little-endian platforms it need to swap the byte-order.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Currently ldpaa ethernet driver rely on DPL file to statically configure
mac address for the DPNIs. It is not a correct approach.
Add support setting MAC address from env variable or Random MAC address.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Convert altera_tse to driver model and phylib.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
remove unused code as the same is achieved when configuring sgmii
and link status is verifed.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In K2G, Ethernet doesn't support SGMII instead it support RGMII,
adding support to the driver to connect to RGMII phy.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Phy mode is a board property and it can be different between
multiple board and ports, so it should not be hardcoded in
driver to one specific mode. So adding a field in eth_priv_t
structure to pass phy mode to driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch uses the eth_is_active() function to work around
issues that prevented compilation with the newer driver model.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently when phy device is created the link variable is
initialized to 1 which denoted phy link is already up. On a power
reset there is no issue as phy status register link status will
not be set, so phy auto negotiate will be started. But when a cpu
reset is issued (ex: dra72x-evm) phy's link status bit is already
set which leads to assume that link is already setup in
genphy_update_link() initial check which results in ehternet not
working. So do not assume that link is already up and on phy
device create set link to zero. This is verified on dra72x-evm.
Reported-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The command:
ethsw [port <port_no>] ingress filtering
{ [help] | show | enable | disable }
- enable/disable VLAN ingress filtering on port
can be used to enable/disable/show VLAN ingress filtering on a port.
This command has also been added to the ethsw generic parser
from common/cmd_ethsw.c
Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The command:
ethsw vlan fdb { [help] | show | shared | private }
- make VLAN learning shared or private"
configures the FDB to share the FDB entries learned on multiple VLANs
or to keep them separated. By default, the FBD uses private VLAN
learning. This command has also been added to the ethsw generic parser
from common/cmd_ethsw.c
Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The new added commands can be used to configure VLANs for a port
on both ingress and egress.
The new commands are:
ethsw [port <port_no>] pvid { [help] | show | <pvid> }
- set/show PVID (ingress and egress VLAN tagging) for a port;
ethsw [port <port_no>] vlan { [help] | show | add <vid> | del <vid> }
- add a VLAN to a port (VLAN members);
ethsw [port <port_no>] untagged { [help] | show | all | none | pvid }
- set egress tagging mod for a port"
ethsw [port <port_no>] egress tag { [help] | show | pvid | classified }
- Configure VID source for egress tag. Tag's VID could be the
frame's classified VID or the PVID of the port
These commands have also been added to the ethsw generic parser from
common/cmd_ethsw.c
Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The new command:
ethsw [port <port_no>] [vlan <vid>] fdb
{ [help] | show | flush | { add | del } <mac> }
Can be used to add and delete FDB entries. Also, the command can be used
to show entries from the FDB tables. When used with [port <port_no>]
and [vlan <vid>], only the matching the FDB entries can be seen or
flushed. The command has also been added to the generic ethsw parser
from cmd_ethsw.c.
Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The command:
ethsw [port <port_no>] learning { [help] | show | auto | disable }
can be used to enable/disable HW learning on a port.
This patch also adds this command to the generic ethsw parser from
cmd_ethsw.
Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The new added command:
ethsw [port <port_no>] statistics { [help] | [clear] }
will print counters like the number of Rx/Tx frames,
number of Rx/Tx bytes, number of Rx/Tx unicast frames, etc.
This patch also adds this commnd in the genereric ethsw
parser from cmd_ethsw.c
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch replaces the parser used by VSC9953 L2 Switch driver with
the generic one. Also, the config macro that enables the
VSC9953 commands has been replaced in all the platforms that
use this driver with the config macro that corresponds to the
generic parser.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
At startup, the default configuration should be:
- enable HW learning on all ports (HW default);
- all ports are VLAN aware;
- all ports are members of VLAN 1;
- all ports have Port-based VLAN 1;
- on all ports, the switch is allowed to remove
maximum one VLAN tag,
- on egress, the switch should add a VLAN tag if the
frame is classified to a different VLAN than the port's
Port-based VLAN;
Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When a port is enabled at init time, the initializing function
touches more bits than necessary to enable a port (also touches
reserved bits and default bit values). This patch fixes this issue
by changing the value of the define used to enable the port and
assures that no other bits are changes by replacing out_le32()
with setbits_le32().
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch groups some macros defined for registers and
replaces some magic numbers from vsc9953 with macros. Also,
"port" and "port_nr" words are replaced with "port_no",
puts each variable declaration on a line and removes
unnecessary tabs.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Designware ethernet controller is also seen on PCI bus, e.g.
on Intel Quark SoC. Add this support in the DM version driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that we have a new header file for cache-aligned allocation, we should
move the stack-based allocation macro there also.
Signed-off-by: Simon Glass <sjg@chromium.org>
When building dm version of designware eth driver on a platform
with 64-bit phys_addr_t, it reports the following warnings:
drivers/net/designware.c: In function 'designware_eth_probe':
drivers/net/designware.c:599:2:
warning: format '%lx' expects argument of type 'long unsigned int',
but argument 3 has type 'phys_addr_t' [-Wformat]
drivers/net/designware.c:600:21:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/net/designware.c:601:21:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
This commit fixes the build warnings.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit converts pch_gbe ethernet driver to driver model.
Since this driver is only used by Intel Crown Bay board, the
conversion does not keep the non-dm version.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Zap variable which is set but never used.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
The MIB RAM and FIFO receive start register does not exist on
i.MX6UL. Accessing these register will cause enet not work well.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Stefano Babic <sbabic@denx.de>
Replace the DMACTRL[LE] hack with recommended settings
for ETSECDMAMCR to get the same end effect - obtaining
big-endian buffer descriptors and frame data for eTSEC.
The reset / default value for ETSECDMAMCR is preserved,
excepting the BD and FR bits which are cleared to enable
the BE mode in accordance with the H/W specifications.
Fixes: 52d00a8 "ls102xa: etsec: Add etsec support for LS102xA"
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Tested-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of VSC8584 phy placed on new QSGMII/SGMII ethernet riser cards
used on LS2085QDS platforms.
Signed-off-by: King Chung Lo@freescale.com <KingChungLo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Recently the FMan Port and MAC compatibles were changed.
This patch aligns the FMan Port and MAC compatibles
to the new FMan device tree binding document.
The FMan device tree binding document can be found in the Linux kernel:
./Documentation/devicetree/bindings/powerpc/fsl/fman.txt
This patch doesn't affect legacy compatibles support.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Tested-by: Xing Lei <xing.lei@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
commit 6497e37 "net: e1000: Support 64-bit physical address" causes
compiler warnings on 32-bit U-Boot build below.
drivers/net/e1000.c: In function 'e1000_configure_tx':
drivers/net/e1000.c:4982:2: warning: right shift count >= width of type [enabled by default]
drivers/net/e1000.c: In function 'e1000_configure_rx':
drivers/net/e1000.c:5126:2: warning: right shift count >= width of type [enabled by default]
This commit fixes the build warnings.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add Kconfig options in preparation for moving boards to use Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Update this driver to support driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Apalis T30 2GB on Apalis Evaluation Board
Since struct eth_device does not exist with CONFIG_DM_ETH defined, avoid
using it in the driver unless necessary. Most of the time it is better to
pass the private driver pointer anyway.
Also refactor the code so that code that the driver model implementation
will share are available in functions that can be called. Add stubs where
necessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Apalis T30 2GB on Apalis Evaluation Board
We cannot currently include any header files in the C files since common.h
needs to be included first, and it is in the header file. Move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Apalis T30 2GB on Apalis Evaluation Board
High 32-bit address is needed when u-boot runs in 64-bit space.
Tested on armv8-based LS2085ARDB.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch enables the NAND controller on the Armada XP/38x and provides
a new function that returns the NAND controller input clock. This
function will be used by the MVEBU NAND driver.
As part of this patch, the multiple BIT macro definitions are moved
to a common place in soc.h.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter Morrow <peter@senient.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Add support to specify the Ethernet buffer base address;
if none are supply by the board, the default value is use (from existing code).
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The current 4.5 timeout for the autonegotiation are not enough to
complete it on my platform. Using the Intel E1000 PCIe card in the
Marvell db-mv784mp-gp eval board. So lets increase the timeout to
8 seconds.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>
Add Ethernet PHY for BCM Cygnus SoC
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
With commit e3a77218a2 the MII bus is only
reset if a reset handler is registered. If there is no reset handler there
is no need to wait for a device to come out of the reset.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
The rxbd is not correctly handled in case of a frame physical error
(FPE) or frame size error (FSE). The rxbd must be cleared and
advanced in case of an error to avoid receive stall.
Signed-off-by: Daniel Inderbitzin <daniel.inderbitzin@gmail.com>
LPC32xx MAC and clock control configuration requires some minor quirks
to deal with a phy connected by RMII.
It's worth to mention that the kernel and legacy BSP from NXP sets
SUPP_RESET_RMII == (1 << 11) bit, however the description of this bit is
missing in shared LPC32x0 User Manual UM10326 Rev. 3, July 22, 2011
and in LPC32x0 Draft User Mannual Rev. 00.27, November 20, 2008, also
in my tests an SMSC LAN8700 phy device connected over RMII seems to
work correctly without touching this bit.
Add support of RMII, if CONFIG_RMII is defined, this option is aligned
with a number of boards, which already define the same config value.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
This change rearranges general MAC configuration and PHY specific
configuration of MAC registers (duplex mode and speed), before this
change set bits related to PHY configuration in MAC2 and COMMAND
registers are rewritten by the following writing to the registers.
Without the change auto negotiation on boot quite often is not
completed in reasonable time:
Waiting for PHY auto negotiation to complete......... TIMEOUT !
Additionally MAC1_SOFT_RESET clear bit is removed since it is done in
preceding lpc32xx_eth_initialize() and in lpc32xx_eth_halt(), instead
added missing MCFG_RESET_MII_MGMT on device initialization.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The lpc32xx_eth_phylib_init() function is capable to connect LPC32XX
MAC to some specified phy by phy id, by chance the single user of
lpc32xx_eth has CONFIG_PHY_ADDR set to 0, however other boards may
have non-zero CONFIG_PHY_ADDR value, fix it.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
According to LPC32x0 User Manual the following bits in Command
register 0x3106_0100 are defined:
Bit Symbol
2 - Unused
3 RegReset
4 TxReset
5 RxReset
Fix wrong (1-bit shifted right) COMMAND_RESETS value, which sets
an unused bit, but neglects RxReset.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tearing down an unitialized rx channel causes a pending address hole
event to be queued. When booting linux it will report this pending
as something like "Address Hole seen by USB_OTG at address 57fff584",
since u-boot did not handled this interrupt. Prevent that by not
tearing down the rx channel, when not receiving.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Support the 88E1510 PHY which is very similar to the 88E1518.
I also set the INTn output and configured the LEDs.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
