The system fails to boot without any environment location, so return
ENVL_NOWHERE when there's nowhere to store the environment instead
of ENVL_UNKNOWN.
The same change was also done by commit 50918d0df5 ("xilinx: Return
ENVL_NOWHERE instead of ENVL_UNKNOWN") for zynq and zynqmp.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/e4ed36408f10159677ed8060bfd5289f3e0691fa.1637752614.git.michal.simek@xilinx.com
The xilinx board_fdt_blob_setup() implementation makes use of
XILINX_OF_BOARD_DTB_ADDR, but no default value is currently defined for
microblaze. Add one so that microblaze could also work with
CONFIG_OF_SEPARATE.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211202195657.246723-1-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
MicroBlaze vector base address is configurable (hdl C_BASE_VECTORS
configuration parameter). Current code assumes that the reset vector
location is always 0x0.
Add the XILINX_MICROBLAZE0_VECTOR_BASE_ADDR Kconfig option so the user
can adjust the reset vector address.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-8-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Migrate CONFIG_SYS_USR_EXCEP to Kconfig. Also, rename it to
XILINX_MICROBLAZE0_USR_EXCEP in order to match the naming convention of
microblaze-generic Kconfig options.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-7-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Previous psu init was targeting SOM + KV260 carrier card and also contain
configurations for other devices on carrier card. This config is removing
all expected configurations for CC and let U-Boot to handle all of it self.
This configuration is designed for SOM itself (and I would bet without
eMMC).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/5782131058dc372befd3fdb4dceabeea5ba56606.1637236693.git.michal.simek@xilinx.com
The SMSC driver is using the old driver model.
Init the virtio system in vexpress64.c so that the network device is
discovered.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Capture x0 in lowlevel_init.S as potential fdt address. Modify
board_fdt_blob_setup to use fdt address from either vexpress_aemv8.h
or lowlevel_init.S.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Rename from vexpress_aemv8a.h -> vepxress_aemv8.h as new FVPs may not be
v8-A. No change in behavior.
This is towards future work to enable support for the FVP_BaseR.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYcsdCQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXCLhAJ9pLJE3SpQRzpm+Nu4EMbCDzZKr+wCfbxnAZ9LC
zS1XZ6u9Se4ysDb+PYs=
=Hf5j
-----END PGP SIGNATURE-----
Merge tag 'video-next-20211228' of https://source.denx.de/u-boot/custodians/u-boot-video into next
- various fixes to the sandbox display support
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
This converts the following to Kconfig:
CONFIG_88F5182
CONFIG_BOARD_IS_OPENRD_BASE
CONFIG_BOARD_IS_OPENRD_CLIENT
CONFIG_BOARD_IS_OPENRD_ULTIMATE
CONFIG_D2NET_V2
CONFIG_FEROCEON
CONFIG_FEROCEON_88FR131
CONFIG_INETSPACE_V2
CONFIG_KW88F6192
CONFIG_KW88F6281
CONFIG_KW88F6702
CONFIG_NET2BIG_V2
CONFIG_NETSPACE_LITE_V2
CONFIG_NETSPACE_MAX_V2
CONFIG_NETSPACE_MINI_V2
CONFIG_NETSPACE_V2
CONFIG_SHEEVA_88SV131
At this point mv-plug-common.h is now only an include of mv-common.h so
remove that indirection.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Signed-off-by: Tom Rini <trini@konsulko.com>
This CONFIG option is used in one of two ways. The first way is that it
is defined to a static value, of an unsigned long size. The second way
is that it is defined to something, typically a function, to determine
this value at run time.
However, in a few cases that function returns a static value. Change
that to using the static value directly.
In the case of using something at run time, convert everything to using
a function of the same name and prototype. This will allow for further
cleanups.
Finally, we have a few cases where the function is just not used, so
drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
When we have CONFIG_DYNAMIC_DDR_CLK_FREQ set is the only time we should
have this function, so guard it so that we can include <clock_legacy.h>
in this file later on.
Signed-off-by: Tom Rini <trini@konsulko.com>
When we have CONFIG_DYNAMIC_DDR_CLK_FREQ set is the only time we should
have this function, so guard it so that we can include <clock_legacy.h>
in this file later on.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the case of CONFIG_SYS_FDT_ADDR this was being used to modify the
default value of fdt_addr / fdt_addr_r, which is not something to expose
in this manner and is not otherwise done. The case of SYS_ENV_ADDR is
similar but only done on the pic32mzdask platform, for scriptaddr.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VID
CONFIG_VOL_MONITOR_INA220
CONFIG_VOL_MONITOR_IR36021_READ
CONFIG_VOL_MONITOR_IR36021_SET
CONFIG_VOL_MONITOR_LTC3882_READ
CONFIG_VOL_MONITOR_LTC3882_SET
To finish this migration, we first need to introduce CONFIG_SPL_VID as
some platforms only use this code in full U-Boot while others use it in
SPL as well. To make the Kconfig logic clearer, guard all of the
sub-options with a if VID || SPL_VID check. Finally, add Kconfig
options for the remaining related options that did not previously have
one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Because of how these symbols work, and the remaining board config.h file
uses, we need to do these at the same time. In some cases we just get
to move rather directly to the defconfigs. A few cases require manual
intervention.
For the case of the eb_cpu5282 we need to select HW_WATCHDOG for the
target, given how it's implemented.
For the cases of m53menlo, dh_imx6, display5, and display5_factory we
disable SPL watchdog support as the particular combination of options
they want would require either more symbols or enabling SPL_DM.
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is used as part of configuring the default environment for a
number of platforms. However, it is always set to 1 and the only time
it is part of Kconfig, it is used in a hard-coded manner. Hard-code the
value in the environment instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
10.1" OF is a capacitive touch 10.1" Open Frame panel solutions.
PX30.Core needs to mount on top of C.TOUCH 2.0 carrier with pluged
10.1" OF for creating complete PX30.Core C.TOUCH 2.0 10.1" Open Frame.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Long gone is the time a custom TF-A was needed for Puma, upstream TF-A
works just fine now.
The flashing instructions are updated to match how newer rkdeveloptool
and rkbin work.
Finally, rkbin provides a way to flash SPI via USB OTG interface so
let's document that.
Cc: Quentin Schulz <foss+u-boot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use this new Kconfig instead of OF_BOARD, so we know for sure which boards
obtain their devicetree from a prior stage. Leave sandbox alone since it
does not. Also don't touch xilinx_versal_virt since it does not have a
specific TARGET Kconfig.
This option implies OF_BOARD for now, but with future work standard
passage may be used instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add rpi_4_32b and rpi_arm64 to the list of boards converted]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move Turris MOX specific remove_disabled_nodes() to fdt_support with
name fdt_delete_disabled_nodes(), so that others can potentially use it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The pre-relocation board topology reading in board_fix_fdt() is
unstable: sometimes wrong data are read from the SPI bus.
This is due to wrong order of SPI bus configuration instructions: we
first need to set the pins to SPI mode, and only after that configure
the bus.
Also add a 1ms delay before enabling chip-select, so that the clock pin
is high for some time before reading the bus.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable eth1 node in U-Boot's device-tree if a network module (SFP, Topaz
or Peridot) is detected.
This is required for proper detection of eth1 comphy in a3700 comphy
driver by the following patches.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
It is better to find DT nodes by compatible strings or aliases instead
of path.
There were issues with Linux some DTBs having different names of some
nodes, e.g.
internal-regs
instead of
internal-regs@d0000000
This should be a generic fix for such issues.
Also since fdt_support now contains needed functions, we can drop our
own implementations.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Since no one uses this feature and I am not aware of any parsers of this
in Linux, remove it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit f0921f5098 ("fdt: Sync up to the latest libfdt") introduced
fdt_generate_phandle() in libfdt, making fdt_alloc_phandle() obsolete in
fdt_support.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: "hui.song" <hui.song_1@nxp.com>
Cc: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace fdt_alloc_phandle() with subsequent fdt_set_phandle() by
fdt_create_phandle().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
No functional change intended. This patch switches from the legacy I2C
API to the DM I2C API, so that this code can be used with DM I2C
enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
The variables retaining the strap values have to be initialized, always,
make it so. Moreover, free the requested GPIO list at the end to avoid
wasting memory.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The rzg2_beacon_defconfig creates an image for RZ/G2[MNH] and
as such creates three different device trees and each of them
have a corresponding -u-boot.dtsi file which are basically
copies of each other. Create a common include file to be
referenced by each of the respective board-u-boot.dtsi files
to reduce duplicate code and simplify support going forward.
This also restores some lost functionality from the device
tree re-sync and updates the MAINTAINER file to include all
beacon-renesom device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
The sunxi MUSB glue driver has some code to check for external VBUS
presence when it's going to use the MUSB host mode, and it warns if
there is VBUS provided through the cable (in sunxi_musb_enable()).
This code was apparently copied to the USB gadget detection code
(g_dnl_board_usb_cable_connected()), but here we actually *expect*
external VBUS power, so a warning is wrong and confusing.
So far this message rarely triggered, but a recent patch (6fa41cdd19)
changed this:
===========================
=> ums 0 mmc 2
UMS: LUN 0, dev mmc 2, hwpart 0, sector 0x0, count 0xe90000
A charger is plugged into the OTG
/A charger is plugged into the OTG
\A charger is plugged into the OTG
|A charger is plugged into the OTG
-A charger is plugged into the OTG
....
===========================
Remove the message for the gadget cable detection call, and just return
the status of the VBUS detection, as this is what the callers are after.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Enable saving environment to SPI flash memory on SiFive
Unmatched.
Signed-off-by: Thomas Skibo <thomas-git@skibo.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Configure SPI flash devices into SPL. Add SPI boot option to spl.c.
Document how to format flash for booting.
Signed-off-by: Thomas Skibo <thomas-git@skibo.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This patch updates Microchip MPFS Icicle Kit support. For now,
add Microchip I2C driver, set environment variables for
mac addresses and default build for SBI_V02.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Load NetXtreme firmware in board_init when BNXT_ETH is selected.
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
Add support of mtd backend for nor1 when this device is present on the
board, on STM32MP157C-EV1 for example, as the support of several MTD
spi-nor instance are now supported with commit b7f060565e ("mtd:
spi-nor: allow registering multiple MTDs when DM is enabled").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable an existing simple framebuffer node in the Linux kernel device
tree and the add the associated reserved memory node to preserved the
resources (clock, memory) used by the stm32 video driver to display
the splashscreen = background in exlinux.conf file.
These resources will be released by the Linux driver only when the
associated driver is ready to avoid transition issues during the Linux
kernel initialization between U-Boot splash screen and the final display.
See Linux documentation for details:
Documentation/devicetree/bindings/display/simple-framebuffer.yaml
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Rename the function named lcd_dt_simplefb* to fdt_simplefb* to be aligned
with the associated file name fdt_simplefb.h/fdt_simplefb.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
The variables retaining the strap values have to be initialized, always,
make it so. Moreover, free the requested GPIO list at the end to avoid
wasting memory.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The Raspberry Pi Foundation released the new Zero 2 W which we
want to detect, so we can detect the correct device tree file name.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The Raspberry Pi Foundation has updated their documentation so update
the URL to the latest place to find the HW device revision codes.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Commit aeb0ca64db ("arm: mvebu: turris_omnia: disable MCU watchdog in
SPL when booting over UART") disabled MCU watchdog when booting over
UART to ensure that watchdog does not reboot the board before UART
transfer finishes.
But if UART transfer fails for some reason, or if U-Boot binary crashes,
then board hangs forever as there is no watchdog running which could
reset it.
To fix this issue, enable A385 watchdog with very high timeout before
disabling MCU watchdog to ensure that even slow transfer can finish
successfully before watchdog timer expires and also to ensure that if
board hangs for some reason, watchdog will reset it.
Omnia's MCU watchdog has fixed 120 seconds timer and it cannot be
changed (without updating MCU firmware). A385 watchdog by default uses
25 MHz input clock and so the largest timeout value (2^32-1) can be
just 171 seconds. But A385 watchdog can be switched to use NBCLK (L2) as
input clock (on Turris Omnia it is 800 MHz clock) and in this case final
watchdog clock frequency is calculated as:
freq = NBCLK / 2 / (2 ^ R)
So A385 watchdog on Turris Omnia can be configured to at most 1374
seconds (about 22 minutes). We set it to 10 minutes, which should be
enough even for bigger U-Boot binaries or slower UART transfers.
Both U-Boot and Linux kernel, when initializing A385 watchdog, switch
watchdog timer to 25 MHz input clock, so usage of NBCLK input clock in
U-Boot SPL does not cause any issues.
Fixes: aeb0ca64db ("arm: mvebu: turris_omnia: disable MCU watchdog in SPL when booting over UART")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
The common emulation Makefile has a dependency on a non-existent
qemu_capsule.o when building with support for capsule update enabled
(CONFIG_EFI_RUNTIME_UPDATE_CAPSULE=y).
The code which was in qemu_capsule.c has been completely moved to
lib/efi_loader/efi_capsule.c by commit 7a6fb28c8e ("efi_loader: capsule:
add back efi_get_public_key_data()").
Remove the false dependency.
This fixes the following build error:
make[1]: *** No rule to make target 'board/emulation/common/qemu_capsule.o', needed by 'board/emulation/common/built-in.o'. Stop.
Fixes: commit 47a25e81d3 ("Revert "efi_capsule: Move signature from DTB to .rodata"")
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Simon Glass <sjg@chromium.org>
Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.
This reverts commit 535870f3b0.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
These conflict with real-word addresses. Use locally administered
MAC addresses and a suitable IPv4 address from 192.0.2.0/24
(TEST-NET-1).
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Alexander Dahl <ada@thorsis.com>
Use a text file for the environment instead of the #define settings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYZPDrwAKCRDKSWXLKUoM
IS9GAJ93T/uprhLcKWMb+284YMb2caWgOACfZ02nTlzvZKNNXVretJgZaHXqj1M=
=cwTL
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.01-rc3
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
The subdivision name "TQ Components" hasn't been in use for a long time.
Rename the vendor directory to "tq", which also matches our Device Tree
vendor prefix.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Config check should be done without the SPL_ prefix.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Link: https://lore.kernel.org/r/20211104192802.3093811-1-ricardo@foundries.io
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We need to filter out NET_ETH_START errors because we have to enable
networking in order to propagate the MAC addresses to the DT while there
is no network driver for the prueth in U-Boot yet.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
- device-tree sync-up with Linux for ls1028a
- fixes/update in fsl-ddr driver, fsl-validate, lx2162a, fsl-mc,
spintable code, configs, qspi node, pci
- enable EFI_SET_TIME support in sl28
- powerpc: Drop -mstring
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
-----BEGIN PGP SIGNATURE-----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=lqEG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211110' of https://source.denx.de/u-boot/custodians/u-boot-stm
- DHSOM update:
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
In some part of STM32MP15 support the CONFIG_TFABOOT can be replaced
by other config: CONFIG_ARMV7_PSCI and CONFIG_ARM_SMCCC.
This patch also simplifies the code in cpu.c, stm32mp1_ram.c and
clk_stml32mp1.c as execution of U-Boot in sysram (boot without SPL and
without TFA) is not supported: the associated initialization code is
present only in SPL.
This cleanup patch is a preliminary step to support SPL load of OP-TEE
in secure world, with SPL in secure world and U-Boot in no-secure world.
Reported-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The DHSOM uses different SPI NOR layout than the ST devkit, stop
pulling in the ST specific runtime mtdparts settings and adjust
the mtdparts accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The stm32 gpio driver private data are not needed in arch include files,
they are not used by code except for stm32 gpio and pincontrol drivers,
using the same IP; the defines for this IP is moved in a new file
"stm32_gpio_priv.h" in driver/gpio.
This patch avoids to have duplicated file gpio.h for each SOC
in MPU directory mach-stm32mp and in each MCU directory arch-stm32*
and allows to remove CONFIG_GPIO_EXTRA_HEADER for all STM32.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a configuration file "stm32mp15_st_common.h" to handle the
STMicroelectronics boards configuration and rename stm32mp1.h to
"stm32mp15_common.h" to handle the generic STM32MP15x series configuration.
The configuration file "dh_stm32mp1.h" is also renamed to
"stm32mp15_dh_dhcom" for the configuration of board based on the
dhelectronics STM32MP15x SOM.
In the STMicroelectronics board configuration the default bootcmd
"bootcmd_stm32mp" is updated to only select the extlinux file found on
SD-Card on STM32MP15x EV1 for boot from NOR device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
I'd like to keep informed about ls1028a.dtsi changes. For now, there is
no top-level entry for any layerscape specific files. Instead, add the
file entry to my board MAINTAINERS file.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Increase fdt blob size for lx2160 and lx2162 series
to fix below errors/warnings during device tree fixup.
Unable to update property /soc/spi@2100000:status, err=FDT_ERR_NOSPACE
Unable to update property /soc/spi@2110000:status, err=FDT_ERR_NOSPACE
Unable to update property /soc/spi@2120000:status, err=FDT_ERR_NOSPACE
WARNING: could not set reg FDT_ERR_NOSPACE.
WARNING unable to set iommus: FDT_ERR_NOSPACE
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Set popts->cpo_sample to 0x54 in t104xrdb/ddr.c to optimize cpo
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
According to ./include/linux/kconfig.h,
CONFIG_IS_ENABLED(OF_BOARD) expands to 0
when CONFIG_SPL_BUILD is defined because
there is no CONFIG_SPL_OF_BOARD.
Use #if defined instead.
Fixes: 2e8d2f8843 ("riscv: Remove OF_PRIOR_STAGE from RISC-V boards")
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The current EFI video driver only works when running in the stub. In that
case the stub calls boot services (before jumping to U-Boot proper) and
copies the graphics info over to the efi table. This is necessary because
the stub exits boot services before jumping to U-Boot.
The app maintains access to boot services throughout its life, so does not
need to do this. Update the driver to support calling boot services
directly.
Enable video output for the app. Note that this uses the
EFI_GRAPHICS_OUTPUT_PROTOCOL protocol, even though it mentions vesa.
A sample qemu command-line for this case is:
qemu-system-x86_64 -bios /usr/share/edk2.git/ovmf-ia32/OVMF-pure-efi.fd
-drive id=disk,file=try.img,if=none,format=raw -nic none
-device ahci,id=ahci -device ide-hd,drive=disk,bus=ahci.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Most modern platforms use 64-bit EFI so it is useful to have a U-Boot app
that runs under that. Add a (non-functional) build for this.
Note that --whole-archive causes the gcc 9.2 linker to crash, so disable
this for now. Once this is resolved, things should work.
For now, avoid mentioning the documentation for the 64-bit app, since it
does not work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- add JetHub D1 eth mac generation with manufacturer OUI
-----BEGIN PGP SIGNATURE-----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=UyL3
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20211102' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- add sm efuse write support and cmd for read/write efuse
- add JetHub D1 eth mac generation with manufacturer OUI
patman 'postfix' support
fix binman test race condition causing a timeout error
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmF+8FcRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYP+AgApwZWYteNQu/OKwCFrZq0QIQYZwJQqe93
9CdQtpKH2boakfNcvsbPP5dXk8GNz5cEky1Whk2kIH1b11FHgklnIPFtFxzMesm8
oYET1w0iItp+4P4ZsQmVgJpynz4yUmUnMEOBNqwI2zeo7dMgx8Zw+cWz8FDo4e6K
pDKHAx9UmiCRu6h+IbsAzeMcq/HqAvFOzoWbp/LkmaWnwIjASCM4UUVoz1+UtoFU
0ENn/7vn70WOLw0JoEib8M7qy+IT7Mz42eZwDVGzYKSDlTZmXNwKLLzgJpEqW4hw
lYIEBUK3sr0q+kcKI776JeFaFhI6k71uVJcjkkUgGuF1hda1kc0Msw==
=E8s4
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-boo21' of https://source.denx.de/u-boot/custodians/u-boot-dm
Environment tidy-ups
patman 'postfix' support
fix binman test race condition causing a timeout error
# gpg: Signature made Sun 31 Oct 2021 03:36:55 PM EDT
# gpg: using RSA key B25C0022AF86A7CC1655B6277F173A3E9008ADE6
# gpg: issuer "sjg@chromium.org"
# gpg: Good signature from "Simon Glass <sjg@chromium.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B25C 0022 AF86 A7CC 1655 B627 7F17 3A3E 9008 ADE6
Allow usage of the bootstage facilities in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sometimes we use uchar and sometimes char for the default environment
array. By always using char, we can get rid of some explicit casts.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Various freescale boards set gd->env_addr to default_environment in
board_init(), conditional on CONFIG_ENV_IS_NOWHERE, but this is
redundant, since it is done by env_init() before board_init() is called.
Let the env subsystem handle this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Samsung Galaxy A3, A5, A7 (2017) - middle class Samsung smartphones.
U-boot can be used as chain-loaded bootloader to gain control
on booting vanilla linux(and possibly others) kernels
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Samsung S9 SM-G9600 - Snapdragon SDM845 version of the phone,
for China \ Hong Kong markets.
Has unlockable bootloader, unlike SM-G960U (American market version),
which allows running u-boot as a chain-loaded bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Stop using the device tree as a source for ad-hoc information.
This reverts commit 2ae7adc659.
Signed-off-by: Michael Walle <michael@walle.cc>
[trini: Also make board/broadcom/bcmns3/ns3.c fail clearly now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that the three M/N/H variants can be built from one config,
rename the defconfig file to be more generic since it supports multiple
RZ/G2.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that TARGET_BEACON_RZG2M can handle all the work that
was done with TARGET_BEACON_RZG2N and TARGET_BEACON_RZG2H,
remove them since they just create more duplicate code.
Signed-off-by: Adam Ford <aford173@gmail.com>
There are three boards from Beacon, RZ/G2 M/N/H which all
use the same board file, but different device trees.
Add code to automatically select the proper device tree
based on the CPU type.
Signed-off-by: Adam Ford <aford173@gmail.com>
JetHome has own MAC OUI. Add jethub-j100 board file. Update config.
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Fix issue reported by checkpatch.pl
WARNING: Possible comma where semicolon could be used
#499: FILE: board/xilinx/zynqmp/zynqmp.c:499:
+ size = ALIGN(CONFIG_SYS_MALLOC_LEN + total_size, MMU_SECTION_SIZE),
+ reg = lmb_alloc(&lmb, size, MMU_SECTION_SIZE);
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/ef264451ef9455ada9784bedbc91f74b94b8a237.1634799528.git.michal.simek@xilinx.com
- mvebu: Fix usage of BIN header arguments (Pali)
- mvebu: turris_omnia: Fix MTD partitions order for Linux (Pali)
- mvebu: nandpagesize support for kwbimage v1 (Pali)
Linux enumerates MTD partitions in DTB order, while the fdt_add_subnode()
function puts a new subnode at the beginning.
To fix this, put MTD partitions into DTB in reverse order.
Fixes: 92f36c8e74 ("arm: mvebu: turris_omnia: fixup MTD partitions in Linux' DTB")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
OF_HOSTFILE is used on sandbox configs only. Although it's pretty
unique and not causing any confusions, we are better of having simpler
config options for the DTB.
So let's replace that with the existing OF_BOARD. U-Boot would then
have only three config options for the DTB origin.
- OF_SEPARATE, build separately from U-Boot
- OF_BOARD, board specific way of providing the DTB
- OF_EMBED embedded in the u-boot binary(should not be used in production
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
On the iMX7ULP uCOM board, OP-TEE uses the memory region defined by the
maximum DRAM address minus CONFIG_OPTEE_TZDRAM_SIZE, so subtract
CONFIG_OPTEE_TZDRAM_SIZE from the available DRAM size to avoid
conflicts.
Note the OPTEE boot process itself subtracts the DRAM region it
lives in from the memory map passed to Linux.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Since we uses the DTS and PHY reset gpio in EQoS driver to do the
reset, remove the duplicated codes from board file.
Signed-off-by: Ye Li <ye.li@nxp.com>
When boot.bin is configured for secure boot the CSU will disable the
JTAG interface on all cases.
Some boards might rely on this interface for flashing to QSPI in which
case those systems might end up bricked during development.
This commit will restore the interface under CSU control
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Link: https://lore.kernel.org/r/20211013134800.19452-1-jorge@foundries.io
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We are printing board information in checkboard() function, which is
called from the default weak implementation of show_board_info().
Rename checkboard() to show_board_info(). This throws away the weak
implementation of show_board_info().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently we always overwrite ethaddrs with those from EEPROM.
In order to allow user to use a cloned MAC address in U-Boot, change the
code so that it sets ethaddr variables only if they aren't set or are
invalid.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently we overwrite ethaddr and eth1addr only if these variables
don't exist.
Better overwrite them even if the env variable exists, but is invalid -
eth_env_get_enetaddr_by_index() checks for validity.
Refactor the code to use a for cycle.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Handle reset button even if we can't configure modules.
This happens if we fail retrieving reset GPIO with which we can reset
the modules.
(Note that this GPIO is different from reset button GPIO.)
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
We are printing board information in last_stage_init(), but U-Boot has
dedicated function, show_board_info(), for this.
Move code which prints board information (board version, serial number,
module topology, ...) to show_board_info().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add code to build the eMMC variant of the Colibri iMX6ULL, i.e. the
'Colibri iMX6ULL 1GB' which has a eMMC instead of the raw NAND used
on other SKUs.
Related-to: ELB-4056, ELB-4057
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Integrate new Toradex SKU 0062 Colibri iMX6ULL 1GB IT. This commit
basically adjusts three parameters of the RAM settings:
Increase density from 4Gb to 8Gb
Increase ROW address from 15 to 16
Increase tRFC (refresh command time) from 260 to 350
This timing is valid for all Toradex Colibri iMX6ULL SKUs
Related-to: ELB-4055, ELB-4057
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add new i.MX 6ULL and 8M Plus SKUs to ConfigBlock handling:
0062: Colibri iMX6ULL 1GB IT (eMMC)
0063: Verdin iMX8M Plus Quad 4GB IT
0064: Verdin iMX8M Plus Quad 2GB Wi-Fi / BT IT
0065: Verdin iMX8M Plus QuadLite 1GB IT
0066: Verdin iMX8M Plus Quad 8GB Wi-Fi / BT
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Restore "Is the module an IT version? [y/N]" for "cfgblock create"
interactive mode command, which was leading to invalid detection
of 0051 Colibri iMX8DX 1GB WB module;
Fixes: a5b5ad4d85 ("toradex: tdx-cfg-clock: add new i.mx 8m mini/plus skus")
Related-to: ELB-3482
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Also take over maintainership of remaining Toradex SoMs as Oleksandr
has left our company.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
CC: Oleksandr Suvorov <cryosay@gmail.com>
After the conversion to binman in commit 8996e6b7c6 ("imx8mm_evk: switch
to use binman to pack images"), it is necessary to flash both flash.bin and
u-boot.itb to get a bootable system. Prior to this commit, only flash.bin
was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single
bootable binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone
(for example, for secure boot purposes).
Also update imx8mm_evk.rst to remove the u-boot.itb copy step.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
NXP used to setup the gpmi clock root from gpmi_clk in early versions
in their downstream BSP. [1]
However on mainline the gpmi clock root was always setup from enfc
since the beginning of the i.MX 6 series SoCs, which is still the same
today. [2]
NXP followed the mainline approach at some point and changed
setup_gpmi_io_clk to setup gpmi clock root from enfc which left faulty
code behind in our board file. [3]
This commit follows the change of NXP as it improves the performance of
the NAND from ~1.2 MiB/s to ~12 MiB/s. [3]
This change was verified to work in recovery-mode and u-boot loaded
from NAND on all four Colibri iMX6ULL SKUs from Toradex.
The frequency used to read the NAND, measured on RE# (Read Enable):
before this patch: 1.4 MHz
after this patch: 22 MHz
in Linux Kernel: 50 MHz
[1] https://source.codeaurora.org/external/imx/uboot-imx/tree/arch/arm/cpu/armv7/mx6/clock.c?h=nxp/imx_v2016.03_4.1.15_2.0.0_ga#n62
[2] commit 23608e23fd ("i.mx: add the initial support for freescale i.MX6Q processor")
[3] https://source.codeaurora.org/external/imx/uboot-imx/commit/?id=7a82a19ceabfb04bbc1591a67c99751748781c7d
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
We drop support for Verdin iMX8M Mini V1.0B.
Related-to: ELB-3551
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Turns out Microship (formerly Micrel) meanwhile integrated proper
support for the DLL setup on their KSZ9131. Unfortunately, this
conflicts with our previous board code doing that.
Fix this by getting rid of our board code and just relying on the
generic implementation relying on rgmii-id being used as phy-mode.
Fixes: commit c6df0e2ffd
("net: phy: micrel: add support for DLL setup on ksz9131")
Fixes: commit af2d3c91d8
("ARM: dts: imx8mm-verdin: Set PHY mode to RGMII-ID")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The following warning is seen in unleashed.c in a 32-bit build:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Cast with uintptr_t.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Commit 47d73ba4f4 ("board: sifive: overwrite board_fdt_blob_setup in u-boot proper")
added a board-specific implementation of board_fdt_blob_setup() which
takes a pointer as the return value, but it does not return anything
if CONFIG_OF_SEPARATE is not enabled. This will cause a build warning
seen when testing booting S-mode U-Boot directly from QEMU, per the
instructions in [1]:
board/sifive/unleashed/unleashed.c: In function ‘board_fdt_blob_setup’:
board/sifive/unleashed/unleashed.c:125:1: warning: control reaches end of non-void function [-Wreturn-type]
Return &_end as the default case.
[1] https://qemu.readthedocs.io/en/latest/system/riscv/sifive_u.html#running-u-boot
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The board can do primary/secondary boot switching, enable the bmode command.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Enable dynamic DDR calibration to have a reliable behavior on edge
temperatures conditions.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Enable dynamic DDR calibration to have a reliable behavior on edge
temperatures conditions.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
At some point back in 2018 prior_stage_fdt_address and OF_PRIOR_STAGE got
introduced, in order to support a DTB handed over by an earlier stage boo
loader. However we have another option in the Kconfig (OF_BOARD) which has
identical semantics.
So let's remove the option in an effort to simplify U-Boot's config and DTB
management, and use OF_BOARD instead.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
At some point back in 2018 prior_stage_fdt_address and OF_PRIOR_STAGE got
introduced, in order to support a DTB handed over by an earlier stage boo
loader. However we have another option in the Kconfig (OF_BOARD) which has
identical semantics.
On RISC-V some of the boards pick up the DTB from a1 and copy it in their
private gd_t. Apart from that they copy it to prior_stage_fdt_address, if
the Kconfig option is selected, which is unnecessary.
So let's switch the config option for those boards to OF_BOARD and define
the required board_fdt_blob_setup() for them.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Update the e-mail addresses and person responsible.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
CC: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
CC: Rainer Boschung <rainer.boschung@hitachienergy.com>
Rather than duplicate the Ethernet MAC address and carveout updating
code for each board, move it to a common location and make it more
reusable.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The EMC frequency tables are created from a training sequence performed
during early boot and passed in via a reserved memory region by nvtboot.
Copy this table to the kernel DTB so that the kernel can use it to scale
the EMC frequency at runtime.
Note that early bootloaders store the EMC table at an address that
currently intersects with the load address of the initial ramdisk. In
order to avoid copying the table to a different address, simply change
the load address for the initial ramdisk in U-Boot.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Support multiple reserved memory regions per device to support platforms
that use both a framebuffer and color conversion lookup table for early
boot display splash.
While at it, also pass along the name, compatible strings and flags of
the carveouts.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reserved memory nodes can have additional flags. Support reading and
writing these flags to ensure that reserved memory nodes can be properly
parsed and emitted.
This converts support for the existing "no-map" flag to avoid extending
the argument list for fdtdec_add_reserved_memory() to excessive length.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The fdtdec_set_carveout() function's parameters are inconsistent with
the parameters passed to fdtdec_add_reserved_memory(). Fix up the order
to make it more consistent.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reserved memory nodes can have a compatible string list to identify the
type of reserved memory that they represent. Support specifying an
optional compatible string list when creating these nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When retrieving a given carveout for a device, allow callers to query
the name. This helps differentiating between carveouts when there are
more than one.
This is also useful when copying carveouts to help assign a meaningful
name that cannot always be guessed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----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=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
The bulk of it is Samuel's DM_I2C rework, which removes the nasty I2C
deprecation warnings for most 32-bit boards. It also includes some
smaller refactorings that pave the way for more changes, mostly driven
by needing to support the Allwinner RISC-V SoC later on.
Board wise we gain support for the FriendlyARM NanoPi R1S H5 router
board and official Pinetab support.
Build-tested for all 160 sunxi boards, and boot tested on a A64, A20,
H3, H6, and H616 board. USB, SD card, eMMC, and Ethernet all work there
(where applicable).
Fix a regression brings by commit 84f8e36f03 ("cmd: bind: allow to
bind driver with driver data")
As example, the following bind command doesn't work:
bind /soc/usb-otg@49000000 usb_ether
As usb_ether driver has no compatible string, it can't be find by
lists_bind_fdt(). In bind_by_node_path(), which called lists_bind_fdt(),
the driver entry is known, pass it to lists_bind_fdt() to force the driver
entry selection.
For this, add a new parameter struct *driver to lists_bind_fdt().
Fix also all lists_bind_fdt() callers.
Fixes: 84f8e36f03 ("cmd: bind: allow to bind driver with driver data")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reported-by: Herbert Poetzl <herbert@13thfloor.at>
Cc: Marek Vasut <marex@denx.de>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Two displays supported by the sunxi display driver (each one used by a
single board) require initialization over I2C. Both previously used
i2c_soft; replace this with the i2c-gpio instance that already exists in
those boards' device trees (sun5i-a13-utoo-p66 and sun6i-a31-colombus).
Since the i2c-gpio nodes are not referenced by any other node in the
device trees (the device trees have no panel node), the I2C bus is
selected by its node name.
This panel initialization code was the only i2c_soft user, so the
i2c_soft GPIO setup code can be removed now as well.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The macro called MUX_VAL generates a writel instruction with
semicolon at the end. This table was written to use semicolons,
however one was missed:
MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /* GPIO_4 */
Since the extra semicolon is unnecessary with the use of the macro,
remove all of them, and cleanup whitespace.
Reviewed-by: Wolfgang Denk <wd@denx.de>
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Adam Ford <aford173@gmail.com>
This adds support for the NanoPi R1S H5 board.
Allwinner H5 SoC
512MB DDR3 RAM
10/100/1000M Ethernet x 2
RTL8189ETV WiFi 802.11b/g/n
USB 2.0 host port (A)
MicroSD Slot
Reset button
Serial Debug Port
WAN - LAN - SYS LED
The dts file is taken from Linux 5.14 tag.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will
remove the asm/arch/gpio.h header. In preparation, clean up the various
files that include it.
Some files did not contain any GPIO code at all, so this header was
completely unused.
A few files contained only legacy platform-specific GPIO code for
setting up pin muxes. They were left unchanged, as that code will be
completely removed by the DM_PINCTRL migration.
The remaining files contain some combination of DM_GPIO and legacy GPIO
code. For those, switch to including asm/gpio.h (if it wasn't included
already). Right now, this header provides both sets of functions,
because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the
right header to include once the DM_GPIO migration is complete and
GPIO_EXTRA_HEADER is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For some systems, such as the PinePhone, there is no way for the end
user to make sure the system is indeed booting before the boot script is
executed, which takes several seconds. Therefore, it can be useful to
provide early visual feedback as soon as possible.
In order achieve this goal, this patch initializes the status LED (if
configured) in the SPL.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Only one board, Yones Toptech BD1078, actually uses a non-default MMC
pinmux. All other uses of these symbols select the default value or an
invalid value. To simplify things, remove support for the unused pinmux
options, and convert the remaining option to a Boolean.
This allows the pinmux to be chosen by the preprocessor, instead of
having the code parse a string at runtime (for a build-time option!).
Not only does this reduce code size, but it also allows this Kconfig
option to be used in a table-driven DM pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The PineTab device-tree is already in u-boot, this commit adds the
corresponding defconfig, based on pinephone_defconfig.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add a host Kconfig for OF_LIBFDT. With this we can use
CONFIG_IS_ENABLED(OF_LIBFDT) directly in the tools build, so drop the
unnecessary indirection.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
DM_GPIO_HOG flag has been replaced by GPIO_HOG flag since a while in
commit 49b10cb492 ("gpio: fixes for gpio-hog support").
And furthermore, gpio_hog_probe_all() is already called in board_r.c.
So gpio_hog_probe() can be removed from stm32mp1.c.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
DM_GPIO_HOG flag has been replaced by GPIO_HOG flag since a while in
commit 49b10cb492 ("gpio: fixes for gpio-hog support").
And furthermore, gpio_hog_probe_all() is already called in board_r.c.
So gpio_hog_probe() can be removed from stm32mp1.c.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Commit ca1a4c8632 ("mvebu: select boot device at SoC level") made it
unnecessary for the A385 boards to have their own kwbimage.cfg but as
the x530 was in flight at the time it was added with it's own
kwbimage.cfg. Remove the custom kwbimage.cfg as the SoC level file is
suitable.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Since the CP1 pinctrl is not properly set in the DTS, there is no
need for setting the pinctrl by writing hardcoded values to the MPP
registers.
So, drop the code relating to that.
Fixes: 87c220d0 ("arm: mvebu: mvebu_armada-8k: Add support for initializing iEi Puzzle-M801 networking")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
The stm32 platforms never had to support an ATAGs-based Linux Kernel,
so remove the bi_boot_params initialization.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The Kontron SoM-Line i.MX8MM (N801x) by Kontron Electronics GmbH is a SoM
module with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC.
The matching evaluation boards (Board-Line) have 2 Ethernets, USB 2.0, HDMI/LVDS,
SD card, CAN, RS485 and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Remove board_ehci_hcd_init function that is not used with DM_USB
and replace its functionality with device-tree configuraton that treats
USB HUB RST# as a gpio enable for the usbh1 vbus regulator.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable LVDS display detection and panel-specific configuration
Make I2C based LVDS detection and configuration model specific:
- not all boards support LVDS connectors; fail detection that do not
support LVDS to avoid misdetecting an I2C device as a display
- GPIO configuration is panel specific; use panel name where needed
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
We configure network phy configuration for internal delay, LED config,
and clock config. If we leave the phy reset gpio defined in dt the
kernel may issue a reset to the phy and break these configs. While some
may be handled by a kernel phy driver, others may not (typically LED
config).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.
Currently there are the following SoM flavors (SoM-Line):
* N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
* N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
* N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND
And the according evaluation boards (Board-Line):
* N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
* N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
* N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...
Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
binman conversion made flashing flash.bin
and u-boot.itb necessary. Update binman config
to create a single flash.bin image again.
This updates imx8mp_evk and phyCORE-i.MX8MP as they share the
same binman config.
Updated also imx8mp_evk documentation.
Tested on phyCORE-i.MX8MP.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
When purchasing imx8mm-cl-iot-gate it is able to customize the
memory size. It could be 1GB, 2GB and 4GB. We implement
board_phys_sdram_size() to detect the memory size for usage.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Currently imx8mm-cl-iot-gate_defconfig fails to produce a working boot
binary due to the lack of fip.bin:
" BINMAN all
Image 'main-section' is missing external blobs and is non-functional: blob-ext
Some images are invalid"
To make the build process more consistent with the other i.MX8M targets,
split the defconfig in two:
- imx8mm-cl-iot-gate_defconfig: standard defconfig that only
requires ATF / DDR firmware.
- imx8mm-cl-iot-gate-optee_defconfig: "more advanced" defconfig that
requires ATF / Optee / mbedtls / DDR firmware.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Display hwmon values by default when using the 'gsc' command.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add documentation bits for the Radxa Zero
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: updated u200 MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add a defconfig for the Radxa Zero SBC, using an Amlogic S905Y2 chip.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: updated u200 MAINTAINERS & add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for new home automation devices.
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting case
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB DDR3
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- Square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB DDR3
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB with serial console
Patches from:
- JetHub H1
https://lore.kernel.org/r/20210915085715.1134940-4-adeep@lexina.inhttps://git.kernel.org/amlogic/c/abfaae24ecf3e7f00508b60fa05e2b6789b8f607
- JetHub D1
https://lore.kernel.org/r/20210915085715.1134940-5-adeep@lexina.inhttps://git.kernel.org/amlogic/c/8e279fb2903990cc6296ec56b3b80b2f854b6c79
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: removed unused variable value]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Beelink GS-King X is a variant of the GS King boards but with an internal
USB to SATA bridge and advanced audio features.
[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Odroid-HC4 is a variant of the Odroid-C4 board but with a PCIe-SATA bridge
instead of the USB3 ports.
[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly. Then, include
<linux/mtd/rawnand.h> where required directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add stub for tee_find_device function when CONFIG_TEE is not activated
to simplify the caller code.
This patch allows to remove the CONFIG_IS_ENABLED(OPTEE) tests
for stm32 platform.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Etienne Carriere <etienne.carriere@inaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
This adds support for the IOT2050 Basic and Advanced devices. The Basic
used the dual-core AM6528 GP processor, the Advanced one the AM6548 HS
quad-core version.
Both variants are booted via a Siemens-provided FSBL that runs on the R5
cores. Consequently, U-Boot support is targeting the A53 cores. U-Boot
SPL, ATF and TEE have to reside in SPI flash.
Full integration into a bootable image can be found on
https://github.com/siemens/meta-iot2050
Based on original board support by Le Jin, Gao Nian and Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last armada100 platform, remove that support
as well.
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last mx35 platform, remove that support as
well.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYVWWZgAKCRDKSWXLKUoM
IY3MAJ43Mlut5tK9gv45bp4HpyVOMuSvJwCfTiVr7ZxrBE8I8QC5+zHzBTmuM6g=
=aQtT
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.01-rc1
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
Generate dfu_alt_info setup at runtime for capsule update.
Enabling this feature will help with upgrading boards without remembering
what is where.
The similar change was done for ZynqMP by commit b86f43de0b ("xilinx:
zynqmp: Add support for runtime dfu_alt_info setup").
Code needs to be enabled by CONFIG_SET_DFU_ALT_INFO.
And also enable capsule on disk for RAW firmware images with efidebug
command.
Two indexes are supported for SPL flow. Images can be generated like:
./tools/mkeficapsule --raw spl/boot.bin --index 1 capsule1.bin
./tools/mkeficapsule --raw u-boot.img --index 2 capsule2.bin
Then place them to SD card and load them:
load mmc 0 10000000 capsule1.bin && efidebug capsule update -v 10000000
load mmc 0 10000000 capsule2.bin && efidebug capsule update -v 10000000
FSBL flow will also work where only index 1 capsule is used. There
should be enough space for using boot.bin with bitstream too.
Zynq also support multiple boot locations in SPI or MMC but it is not wired
by this patch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/bea5fc75a87a5971f118b46bab4aa7ca39a629c6.1630061610.git.michal.simek@xilinx.com
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
After the discussion here:
https://lore.kernel.org/netdev/20210603143453.if7hgifupx5k433b@pali/
which resulted in this patch:
https://patchwork.kernel.org/project/netdevbpf/patch/20210704134325.24842-1-pali@kernel.org/
and many other discussions before it, notably:
https://patchwork.kernel.org/project/linux-arm-kernel/patch/1512016235-15909-1-git-send-email-Bhaskar.Upadhaya@nxp.com/
it became apparent that nobody really knows what "SGMII 2500" is.
Certainly, Freescale/NXP hardware engineers name this protocol
"SGMII 2500" in the reference manuals, but the PCS devices do not
support any "SGMII" specific features when operating at the speed of
2500 Mbps, no in-band autoneg and no speed change via symbol replication
. So that leaves a fixed speed of 2500 Mbps using a coding of 8b/10b
with a SERDES lane frequency of 3.125 GHz. In fact, "SGMII 2500 without
in-band autoneg and at a fixed speed" is indistinguishable from
"2500base-x without in-band autoneg", which is precisely what these NXP
devices support.
So it just appears that "SGMII 2500" is an unclear name with no clear
definition that stuck.
As such, in the Linux kernel, the drivers which use this SERDES protocol
use the 2500base-x phy-mode.
This patch converts U-Boot to use 2500base-x too, or at least, as much
as it can.
Note that I would have really liked to delete PHY_INTERFACE_MODE_SGMII_2500
completely, but the mvpp2 driver seems to even distinguish between SGMII
2500 and 2500base-X. Namely, it enables in-band autoneg for one but not
the other, and forces flow control for one but not the other. This goes
back to the idea that maybe 2500base-X is a fiber protocol and SGMII-2500
is an MII protocol (connects a MAC to a PHY such as Aquantia), but the
two are practically indistinguishable through everything except use case.
NXP devices can support both use cases through an identical configuration,
for example RX flow control can be unconditionally enabled in order to
support rate adaptation performed by an Aquantia PHY. At least I can
find no indication in online documents published by Cisco which would
point towards "SGMII-2500" being an actual standard with an actual
definition, so I cannot say "yes, NXP devices support it".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
After getting MTD device via get_mtd_device_nm(), we need to put it with
put_mtd_device(), otherwise we get
Removing MTD device #0 (mx25l6405d) with use count 1
before booting kernel.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
