The SPL image overflows when cpsw dt nodes are added and SPL_OF_CONTROL
is enabled. Use static platdata instead to save space.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Create a ft_board_setup() api that gets called as part of
DT fixup before jumping to kernel. In this ft_board_setup()
call fdt_fixup_msmc_ram that update msmc sram node.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
If SW 8 pins 0 and 1 indicate that NAND should be enabled then
the pins pinmux must be reconfigured for NAND mode.
Therefore, enable NAND by reconfiguring the pinmux.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
By default VOUT3 occupies the pins required for NAND. Therefore, create
a seperate entry that can be use to reconfigure these pins to work for
NAND.
On the EVM SWITCH 8 pins 0 and 1 will be used to determine if NAND is
enabled or not. For NAND to be selected pin 0 should be on and pin 1
should be off. Any other combination will assume NAND shouldn't be
enabled.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
This patch adds a workaround to reset the phy one time during boot
using GPIO0 pin 10 to make sure, the Phy latches the configuration
from the input pins correctly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch updates pinmux configuration for K2G GP EVM based on
data generated by the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This add pinmux configuration for rgmii interface so that network
driver can be supported on K2G ICE boards. The pinmux configurations
for this are generated using the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
As this required some BUFFER_CLASS definitions, same is re-used
from the linux defnitions in include/dt-bindings/pinctrl/keystone.h
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When these were moved from mach-omap2 to board files they got placed
inside TI_SECURE_DEVICE ifdef block, they are not secure only, move
them up and out.
Fixes: 413b90777f ("ti: fastboot: Move weak overrides to board files")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
- Switch to using the omap3-u-boot.dtsi file for needed properties.
- Remove a few SPL features to free up more SRAM space.
- Switch CONFIG_SYS_TEXT_BASE to the normal default, we don't need to
worry about X-Loader at this point anymore.
- A few related updates to SPL options as part of switching to DM SPL.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
am43xx_evm_ethboot_defconfig is not being actively used and has not been
moved to DM or DT. Also, ethboot cannot be tested on AM43xx EVM as such
due EVM limitations. Therefore delete it.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These defconfigs don't seem be actively used any more, and have not been
moved to adapt DM or DT. Therefore delete them.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable USB clocks in late init stage to support ports under DM_USB.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C
API when DM_I2C is used. The goal is to eventually remove DM_I2C_COMPAT
when all I2C "clients" have been migrated to use the DM API.
This a step in that direction for the TI based platforms.
Build tested with buildman:
buildman -dle am33xx ti omap3 omap4 omap5 davinci keystone
boot tested with:
am335x_evm, am335x_boneblack, am335x_boneblack_vboot (DM version),
am57xx_evm, dra7xx_evm, k2g_evm, am437x_evm
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The EEPROM reading in the board detection code is done through legacy
I2C functions which on platforms using DM_I2C this functionality is
provided via the CONFIG_DM_I2C_COMPAT layer. To allow newer platforms
to use the board detection code without relying on CONFIG_DM_I2C_COMPAT
go ahead and add an I2C handling implementation that directly uses the
I2C DM functionality.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Enable DM_USB and DM_USB_DEV for AM57xx based boards.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable USB clocks in late init stage to support ports under DM_USB.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For USB ports that use the Driver Model, turn on the clocks during the
late init stage.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently k2 spi boot is broken as the image header
is getting copied to an invalid memory location
CONFIG_SYS_TEXT_BASE - sizeof (struct image_size)
which maps to 0xc000000 - 0x40 = 0xbffffc0 being a reserved
location.
We cannot change the CONFIG_SYS_TEXT_BASE address as the single
stage boots like UART boot will need the address to be 0xc000000
hence override the spl_get_load_buffer to have image_header
address as CONFIG_SYS_TEXT_BASE aka 0xc000000
Signed-off-by: Keerthy <j-keerthy@ti.com>
Update the README file to add r5 build support and system
firmware support.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Add initial defconfig support for AM65x
that runs on R5.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Add initial support for AM654 based EVM running on R5.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Networking support for all TI K2 boards converted to use DM model and
CONFIG_DM_ETH enabled in all corresponding defconfig files, hence drop
unused non DM K2 networking code.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
The uinitrd fixup logic should be executed after the FDT /chosen
node has been properly populated by fdt_initrd()
Signed-off-by: Nicholas Faustini <nicholas.faustini@azcomtech.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On beaglebone black, it can so happen that PHY address
is not latched correctly on reset and board boots with
PHY responding to a different address than that
programmed in device-tree. For example, see this report:
https://groups.google.com/d/msg/beagleboard/9mctrG26Mc8/1FuI_i5KW10J
Workaround this by fixing up device-tree passed to kernel
by using the PHY address detected in hardware.
Beaglebone itself uses only one ethernet port and its DT
currently uses phy_id (obsoleted). But the function has
been written to handle multiple ports and phy_id as well
as phy-handle to make the function more generically useful.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add initial support for AM654 based EVM running on A53. Enable
4GB of DDR available on the EVM so that kernel DTB file
can be updated accordingly.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[Andreas: Added 4GB ddr support]
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:
* Gigabit capable PHY
* Extra USB hub, optional i2c control
* lps3331ap barometer connected over i2c
* MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
* 1GiB DDR3 RAM
* RTL8723 Wifi/Bluetooth connected over USB
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some times gcc may generate data that is then used within code that may
be part of an efi runtime section. That data could be jump tables,
constants or strings.
In order to make sure we catch these, we need to ensure that gcc emits
them into a section that we can relocate together with all the other
efi runtime bits. This only works if the -ffunction-sections and
-fdata-sections flags are passed and the efi runtime functions are
in a section that starts with ".text".
Up to now we had all efi runtime bits in sections that did not
interfere with the normal section naming scheme, but this forces
us to do so. Hence we need to move the efi_loader text/data/rodata
sections before the global *(.text*) catch-all section.
With this patch in place, we should hopefully have an easier time
to extend the efi runtime functionality in the future.
Signed-off-by: Alexander Graf <agraf@suse.de>
[agraf: Fix x86_64 breakage]
The pin used for HDMI HPD should be set to GPIO mode on DRA76, similarly
to all the other DRA7 and AM5 SoCs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Overriding fastboot_set_reboot_flag() in arch/arm/mach-omap2/boot-common.c
leaves it applying all boards that derive from this, not just the ones which
have support for Android bootloader flow. Move the weak function override to
the relevant board files.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to
drivers/fastboot.
Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants
FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split
USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing
behaviour.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
A common voltage of 1.35V was being programmed for all am43 board
versions. EPOS-EVM Needs 1.20V for LPDDR2.
Fixes: fc69d47262 (“board: ti: AM43XX: Add ddr voltage rail configuration”)
Reported-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If CONFIG_SPL_SERIAL_SUPPORT is not set, then the build will fail:
board/ti/am335x/built-in.o: In function `spl_start_uboot':
board/ti/am335x/board.c:247: undefined reference to `serial_tstc'
board/ti/am335x/board.c:247: undefined reference to `serial_getc'
Avoid the calls to the serial functions in that case.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.
This fixes failures such as:
board/ti/am335x/built-in.o: In function `board_late_init':
board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'
which caters for use cases such as:
commit f411b5cca4 ("board: am335x: Always set eth/eth1addr environment
variable")
when Ethernet is required in Linux, but not U-Boot.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
When compiling without CONFIG_CLOCK_SYNTHESIZER (which is implied by
CONFIG_DRIVER_TI_CPSW for am335x_evm), exclude the network setup for
AM335x-ICEv2 to avoid link time failures:
board/ti/am335x/board.c:683: undefined reference to `setup_clock_synthesizer'
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
AM437x QSPI boot is a single stage boot and hence needs runtime DTB
selection to support AM437x-SK and AM437x-IDK with DM enabled. This is
required to move am43xx_evm_qspiboot_defconfig to use DM/DT.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Kernel stores information to the RTC_SCRATCH0 and RTC_SCRATCH1 registers
for wakeup from RTC-only mode with DDR in self-refresh. Parse these
registers during SPL boot and jump to the kernel resume vector if the
device is waking up from RTC-only modewith DDR in Self-refresh.
The RTC scratch register layout used is:
SCRATCH0 : bits00-31 : kernel resume address
SCRATCH1 : bits00-15 : RTC magic value used to detect valid config
SCRATCH1 : bits16-31 : board type information populated by bootloader
During the normal boot path the SCRATCH1 : bits16-31 are updated with
the eeprom read board type data. In the rtc_only boot path the rtc
scratchpad register is read and the board type is determined and
correspondingly ddr dpll parameters are set. This is done so as to avoid
costly i2c read to eeprom.
RTC-only +DRR in self-refresh mode support is currently only enabled for
am43xx_evm_rtconly_config.
This is not to be used with epos evm builds.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[j-keerthy@ti.com Rebased to latest u-boot master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Texas Instruments AM3358 based low-cost board using Octavo Systems OSD3358 SIP
with built-in TPS65217 PMIC and 512MB DDR3. Board features small 35mm x
55mm size, high-speed USB OTG, microSD and 72 0.1" expansion header
pins with 2xSPI, 2xI2C, 2xUART, USB, 8xADC, up-to-44 GPIO, PRU pins and much more.
https://beagleboard.org/pocket
This was tested using the am335x_evm_usbspl_defconfig.
Note that MII pins are enabled despite not having Ethernet on this
board. This avoids an issue where otherwise many timeout errors would be
generated. See https://e2e.ti.com/support/arm/sitara_arm/f/791/t/298976
for some related discussion.
Signed-off-by: Jason Kridner <jdk@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
It is safe to always setup the pinmux for UART1 and UART3 to be used in
early_padconf and then if these pins are needed later on, they will be
re-muxed. This allows us to drop the usage of CONFIG_CONS_INDEX here.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
serial# variable is needed to show the device correctly in "fastboot
devices" output. It's useful when we have several devices (in fastboot
mode) connected to single host and want to choose which one to flash.
We can't use omap_die_id_serial() for this, because AM335x lacks
DIE_ID, as can be seen from AM335x TRM. Let's do next:
- reuse board_serial variable (obtained from EEPROM in
set_board_info_env() function) to set serial#
- if board_serial is "unknown", reuse ethaddr variable to set serial#
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
BeagleBoard 'xM' does not really have NAND. CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT can/should be empty for 'xM'. This commit sets
the defined values if they exist.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER.
This enables users to block text using CONFIG_IS_ENABLED() instead
of resorting to #if ladders with SPL and non-SPL cases.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
This seems to have been missed, possibly due to the inability to
enable TI_SECURE_DEVICE on Keystone2 devices previously.
Fixes: bfebc8c965 ("env: Rename getenv_hex(), getenv_yesno(), getenv_ulong()")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Since DRA7xx/AM57xx SR1.1 and SR1.0 has errata to limit the frequency of
MMC1 to 96MHz and frequency of MMC2 to 48MHz for AM572x SR1.1, limit the
frequency and disable higher speed modes for those revision.
Also use the recommended IO delays (those tagged with "rev11")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
board_usb_init()/_cleanup() should be in board files and don't have
a place in the xhci-omap driver. Weak versions for
board_usb_init()/_cleanup() already exist in common/usb.c
(for host mode) and drivers/usb/gadget/g_dnl.c (for gadget mode).
Therefore, remove init and cleanup functions from xhci-omap and
implement them in the board files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
hw_data_init() is called before relocation to initialise hardware data.
Since ctrl is initialized to OMAP_SRAM_SCRATCH_SYS_CTRL in
arch/arm/mach-omap2/am33xx/hw_data.c, the pointer *ctrl will not be
updated during relocation and will hold a stale value.
Therefore call hw_data_init() again after relocation to
reinitialize *ctrl.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Update the board pinmux for AM574x-IDK board using latest PMT[1] and the
board files named am574x_idk_v1p3b_sr2p0 that were auto generated on
13th October, 2017 by "Ahmad Rashed <a-rashed@ti.com>".
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM574x-idk has the following DDR parts attached:
EMIF1: MT41K256M16HA (1GB with ECC)
EMIF2: MT41K256M16HA (1GB without ECC)
Enabling 2GB DDR without interleaving between EMIFs. And
enabling ECC on EMIF1.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
DRA762 comes in two packages:
- ABZ: Pin compatible package with DRA742 with DDR@1333MHz
- ACD: High performance(OPP_PLUS) package with new IPs
Both the above packages uses the same IDCODE hence needs to
differentiate using package information in DIE_ID_2.
Add support for the same. Also update clock, ddr, emif information.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
All ddr3_emif declarations are not used outside ddr3_k2g.c
file. So make all of them as static.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
gpio1_2 is used for HPD interrupt with DRA76's DVI add-on board, so mux
the pin as gpio and PIN_INPUT.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Added support for K2G EVM with FlipChip SoC of which
ARM/DDR3 runs at 1GHz/1066 MT/s. The patch is also
backward compatible with old revision EVM and EVM
with WireBond SoC. Their ARM/DDR3 run at 600MHz/800 MT/s.
The new SoC supports 2 different speeds at 1GHz and 600MHz.
Modyfied the CPU Name to show which SoC is used in the EVM.
Modified the DDR3 configuration to reflect New SoC supports
2 different CPU and DDR3 speeds, 1GHz/1066MT and 600MHz/800MT.
Added new inline function board_it_k2g_g1() for the new FlipChip 1GHz,
and set the u-boot env variable board_name accordingly.
Modified findfdt script in u-boot environment variable to include new k2g board type.
Signed-off-by: Rex Chang <rchang@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
MCAN can be accessed via DCAN1 or DCAN2. Determining which DCAN instance
to use if any at all is done through
CTRL_CORE_CONTROL_SPARE_RW.SEL_ALT_MCAN. Since general pinmuxing is
handled in U-boot. Handle this additional pinmuxing requirement in U-boot
to ensure that MCAN is used by default via the DCAN1 pins.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
[fcooper@ti.com: Update commit message and use DCAN1 not DCAN2 for MCAN]
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
This commit clears 'ethaddr' before calling 'smc911x_initialize' to
allow the SROM MAC address to be assigned properly.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
This header was renamed to rawnand.h in Linux.
The following is the corresponding commit in Linux.
commit d4092d76a4a4e57b65910899948a83cc8646c5a5
Author: Boris Brezillon <boris.brezillon@free-electrons.com>
Date: Fri Aug 4 17:29:10 2017 +0200
mtd: nand: Rename nand.h into rawnand.h
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When usb_hub_reset_devices is called, it should be passed both an
indicator which hub it should operate on and what port number (local
to that hub) should be reset.
Previously, the usb_hub.c code did not include such context and
always started resets from port number 1, performing multiple
reset-requests for the same devices:
/*
* Reset any devices that may be in a bad state when applying
* the power. This is a __weak function. Resetting of the devices
* should occur in the board file of the device.
*/
for (i = 0; i < dev->maxchild; i++)
usb_hub_reset_devices(i + 1);
This adds an additional 'hub' parameter to usb_hub_reset_devices
that provides the context to fully qualify the port-number in.
Existing implementations are changed to accept and ignore the new
parameter.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
All regulators are hooked to EN_Pin at reset so that EN Pin controls
their state. Hook the LDO1 regulator to EN pin which at reset is not
hooked. This applies only to LP8733.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This comment creates a wrong entry in config_whitelist.txt.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
CONFIG_FIT_EMBED might be confused with CONFIG_OF_EMBED, rename it
MULTI_DTB_FIT as it is able to get a DTB from a FIT image containing
multiple DTBs. Also move the option to the Kconfig dedicated to the DTS
options and create a README for this feature.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Add support for detection
of SR2.1 version of DRA71x family of processors.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The PMMC firmware should be bundled into a FIT image on HS
devices to allow authentication/decryption, add a handler to
process this PMMC firmware.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Add support for selecting proper dtb for
am57xx BeagleBoard X15 revC u-boot from FIT
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
AM571x supports DDR running at 666MHz. Right now it is
clocked at 532MHz which is lower than what is supported.
In order to have maximum performance on AM571-IDK,
switch DDR to 666MHz.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for selecting proper dtb for
dra76x u-boot from FIT.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adding pinmux and IODELAY data for dra76-evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76-evm has the ddr parts connectedi running at 666MHz:
EMIF1: MT41K512M16HA-125 AIT:A x 2
EMIF2: MT41K512M8RH-125-AAT:E x 4
Add support for configuring the above DDR parts.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76-evm uses lp8736 and tps65917 pmic for powering on
various peripherals. Add data for these pmics and register
for dra76-evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The dra76-evm is a board based on TI's DRA76 processor
Add eeprom support
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
It is not necessary that ldo1 is used to power on mmc.
So, add support for passing ldo registers for powering on mmc.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
It is not necessary all omap5+ based uses the same PMIC
to poweron mmc. So add support for enabling mmc based on board.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
- Pass MTDPARTS kernel arguments to kernel
- Use Kconfig CONFIG_NAND instead of CONFIG_SYS_EXTRA_OPTIONS="NAND"
- Call 'usb_stop' on kernel start
- Update Falcon mode setup to match other OMAP3 boards
- Use "uEnv.txt" as boot script instead of "boot.scr"
We are now using an env_ prefix for environment functions. Rename these
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
This is a strange name for a function that loads the environment. There is
now only one implementation of this function, so use the new env_load()
function directly instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present we support multiple environment drivers but there is not way to
select between them at run time. Also settings related to the position and
size of the environment area are global (i.e. apply to all locations).
Until these limitations are removed we cannot really support more than one
environment location. Adjust the location to be a choice so that only one
can be selected. By default the environment is 'nowhere', meaning that the
environment exists only in memory and cannot be saved.
Also expand the help for the 'nowhere' option and move it to the top since
it is the default.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Move all of the imply logic to default X if Y so it works again]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch brings the OMAP3 EVM to a bootable state, on master, as of
v2017.09-rc1.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Traditional KS2 devices supported NAND via the AEMIF peripheral. However,
66AK2G doesn't use the AEMIF but rather the GPMC for NAND. Therefore,
clarify some statements to indicate only certain devices have AEMIF and
in other places just say NAND instead of AEMIF NAND
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
The driver is for all boards 24XX and up, so let's eliminate the
extra option called CONFIG_SYS_I2C_OMAP34XX since the driver checks
for CONFIG_OMAP34XX we don't need CONFIG_SYS_I2C_OMAP34XX.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
When we have MMC available we assume that we want to put the env as a
file on FAT.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
BeagleBoard X15 revC board is similar to X15 revB1 except
with a SR2.0 where revB1 uses a SR1.1. Add board detection
support for revC.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
board_is*("rev", board_ti_get_rev()) uses strncmp() for
revison detection and assumes it is success if return value
is <= 0. This will fail in case of multiple versions, as
revb will be true for board_is_*revb() and board_is_*reva().
Fix it by looking for exact match of the string.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
K2G ICE evm will have its own dtb. Therefore, add it to the list of dtbs
located in the appended U-boot dtb FIT image. Therefore, when swapping out
dtbs K2G ICE boards can grab the correct one.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to allow "board_name" to
be set depending on the board it is being ran on.
Update findfdt to use this new dynamic board_name value to determine
which dtb should be used.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Certain peripherals used by K2G GP aren't used on K2G ICE evm. Or
configuration is slightly different. Therefore, use board detection to
deal with these variations.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some code doesn't apply to K2G ICE evm. Therefore, use board detection to
wrap these calls.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add configuration settings used by the K2G ICE evm. Also use board
detection to determine which DDR3 configuration to use.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add basic pinmux data for new K2G ICE evm. Also add pinmuxing for a
generic K2G evm which includes I2C 0 and 1 used for board detection
purposes.
Since multiple K2G boards are supported that means initially generic
pinmuxing should be used when board detection hasn't ran. Once board
detection runs the proper pinmuxing can be reran to match the board
being ran on.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a function that can be used to determine if the board being ran on is
a K2G Industrial Communication Engine EVM or K2G General Purpose EVM based
on values programmed on the EEPROM.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Different K2G evms may need to program the various
KS2_DDRPHY_DATX8_X_OFFSET registers in different ways. Therefore, use
the mask and val registers for each KS2_DDRPHY_DATAX_X_OFFSET to
properly program the register.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
K2G GP doesn't require the MR2 register to be programed since the
default is good enough. However, newer K2G boards do need to change
this register value. Therefore, instead of not writing this register if
ran on a K2G board just program the value to be written to match the
default/reset value.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some K2G evms have their EEPROM programming while most do not. Therefore,
add EEPROM board detection to be used as the default method and fall back
to the alternative board detection when needed.
Also reorder board configuration. Perform bare minimal configuration
initially since board detection hasn't ran. Finish board configuration
once the board has been identified.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now with support for U-boot runtime dtb selection each board needs to
define board_fit_config_name_match so U-boot can determine what the
correct dtb is within the FIT blob.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For K2G, runtime DTB selection utilizes the embedded_dtb_select function.
Therefore, define the function which will perform a EEPROM read and then
retries selecting the correct dtb now that it can detect which board its
on. For other Keystone devices use an empty function since they will still
use the embedded FIT functionality but their FIT will only contain a single
dtb.
Most production K2G boards do not have their EEPROM programmed. Therefore,
perform a test to verify a K2G GP is currently being used and if it is then
set the values normally set by a EEPROM read.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When the EEPROM is first read its contents are stored in memory as a
cache to avoid further I2C operations. To determine if the EEPROM was
previously read the easiest way is to check the memory to see if the
EEPROM's magic header value is set. Create a new function that can
determine if the EEPROM was previously read or not without having to
perform a I2C transaction.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In some situations the EEPROM used for board detection may not be
programmed or simply programmed incorrectly. Therefore, it may be
necessary to "simulate" reading the contents of the EEPROM to set
appropriate variables used in the board detection code.
This may also be helpful in certain boot modes where doing i2c reads
may be costly and the config supports running only a specific board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Franklin S Cooper Jr. <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The ti816x SoC revision of the ethernet IP block is handled by the
"davinci_emac" driver, rather than the "cpsw" driver as done by later
members of the family. Enable the relevant plumbing.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
commit 0650798824 ("board: am335x: Introduce scale_vcores")
updated voltages of each board based on efuse. It updated
beagle bone specific voltages under the condition board_is_bone().
But this is true only for BeagleBoneWhite. Due to which voltages
are not configured for BBB, BBW as wrong device is being probed.
So create a common function board_is_beaglebonex() which includes
am335x based beagle family. Use this for updating voltages.
Also remove extra if condition for selecting voltages which is
done later using a switch case and match usb current limit as
before the commit 0650798824.
Fixes: 0650798824 ("board: am335x: Introduce scale_vcores")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
One can obtain those variables using next commands:
$ fastboot getvar cpu
$ fastboot getvar secure
$ fastboot getvar board_rev
$ fastboot getvar userdata_size
Those variables are needed for fastboot.sh script.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
One can obtain those variables using next commands:
$ fastboot getvar cpu
$ fastboot getvar secure
$ fastboot getvar board_rev
$ fastboot getvar userdata_size
Those variables are needed for fastboot.sh script.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the board pinmux for AM572x-evm using latest PMT[1] and the
board files named am572x_gp_evm_A3a_sr2p0 and am572x_gp_evm_A2b_sr1p1
that were autogenerated on 30th January, 2017 by
"Ahmad Rashed <a-rashed@ti.com>" and "Tom Johnson <thjohnson@ti.com>".
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update the board pinmux for AM571x-IDK board using latest PMT[1] and the
board files named am571x_idk_v1p3b_sr2p0 that were autogenerated on
23rd March, 2017 by "Ahmad Rashed <a-rashed@ti.com>" and
"Tom Johnson <thjohnson@ti.com>".
[1] https://dev.ti.com/pinmux/app.html#/default/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update the board pinmux for AM572x-IDK board using latest PMT[1] and the
board files named am572x_idk_v1p3b_sr2p0 that were autogenerated on
30th January, 2017 by "Ahmad Rashed <a-rashed@ti.com>" and
"Tom Johnson <thjohnson@ti.com>".
[1] https://dev.ti.com/pinmux/app.html#/default/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Refactor OMAP3/4/5 code so that we have only one get_device_type()
function for all platforms.
Details:
- Add ctrl variable for AM33xx and OMAP3 platforms (like it's done for
OMAP4/5), so we can obtain status register in common way
- For now ctrl structure for AM33xx/OMAP3 contains only status register
address
- Run hw_data_init() in order to assign ctrl to proper structure
- Remove DEVICE_MASK and DEVICE_GP definitions as they are not used
(DEVICE_TYPE_MASK and GP_DEVICE are used instead)
- Guard structs in omap_common.h with #ifdefs, because otherwise
including omap_common.h on non-omap4/5 board files breaks compilation
Buildman script was run for all OMAP boards. Result output:
arm: (for 38/616 boards)
all +352.5
bss -1.4
data +3.5
rodata +300.0
spl/u-boot-spl:all +284.7
spl/u-boot-spl:data +2.2
spl/u-boot-spl:rodata +252.0
spl/u-boot-spl:text +30.5
text +50.4
(no errors to report)
Tested on AM57x EVM and BeagleBoard xM.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Rework the guards as to not break TI81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add ddr voltage rail (dcdc3) configuration. Set the dcdc3
DDR supply to 1.35V.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Rather than relying on common.h to provide this include, which is going
away at some point, include it explicitly in each file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
- Switch to using <configs/ti_armv7_omap.h> and family. This lets us
drop lots of custom defines.
- Ensure that our default environment uses DEFAULT_LINUX_BOOT_ENV so
that Linux will boot correctly.
- Enable CONFIG_DISTRO_DEFAULTS
- Switch to using CONFIG_OF_CONTROL
- Various other cleanups to match other SoCs in the family line.
Signed-off-by: Tom Rini <trini@konsulko.com>
The ti816x/am389x SoC is the first generation in what U-Boot calls the
"am33xx" family. In the first generation of this family the DDR
initialization sequence is quite different from all of the subsequent
generations. Whereas with ti814x (second generation) we can easily work
the minor differenced between that and am33xx (third generation), our
attempts to do this for ti816x weren't sufficient. Rather than add a
large amount of #ifdef logic to make this different sequence work we add
a new file, ti816x_emif4.c to handle the various required undocumented
register writes and sequence and leverage what we can from
arch/arm/mach-omap2/am33xx/ddr.c still. As DDR2 has similar problems
today but I am unable to test it, we drop the DDR2 defines from the code
rather than imply that it works by leaving it. We also remove a bunch
of other untested code about changing the speed the DDR runs at.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently these (board agnostic) commands cannot be selected using
menuconfig and friends. Fix this the obvious way. As part of this,
don't muddle the meaning of CONFIG_HASH_VERIFY to mean both 'hash -v'
and "we have a hashing command" as this makes the Kconfig logic odd.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[trini: Re-apply, add imply for a few cases, run moveconfig.py, also
migrate CRC32_VERIFY]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_EEPROM
CONFIG_CMD_EEPROM_LAYOUT
CONFIG_EEPROM_LAYOUT_HELP_STRING
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework Kconfig logic slightly, define EEPROM location on TI eval
platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add #undef CONFIG_DM_MMC_OPS to omap3_logic in the SPL build case, to
match other TI platforms in the same situation.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Now CONFIG_GENERIC_MMC and CONFIG_MMC match for all defconfig.
We do not need two options for the same feature. Deprecate the
former.
This commit was generated with the sed script 's/GENERIC_MMC/MMC/'
and manual fixup of drivers/mmc/Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Drop use of this long-deprecated option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
am335x supports various sysclk frequencies which can be determined
using sysboot pins. PLLs should be configures based on this
sysclk frequency. Add PLL configurations for all supported
frequencies.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In non DM I2C read operations the address length passed in during a read
operation will be used automatically. However, in DM I2C the address length
is set to a default value of one which causes problems when trying to
perform a read with a differing alen. Therefore, before the first read in a
series of read operations set the alen to the correct value.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reading from the I2C EEPROM used typically requires using an address length
of 2. However, when using DM for I2C the default address length used is 1.
To fix this introduce a new function that allows the address length to be
changed. The logic to do so was copied from cmd/i2c.c.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
