Discard all .dynsym sections from linker scripts
Remove all __dynsym_start definitions from linker scripts
Remove all __dynsym_start references from the codebase
Note: this touches include/asm-generic/sections.h, which
is not ARM-specific, but actual uses of __dynsym_start
are only in ARM, so this patch can safely go through
the ARM repository.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Move pinmux configurations for the DA830 SoCs from board file
to the arch tree so that it can be used for all da830 based devices.
Also, avoids duplicate pinmuxing in case of NAND.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
The vectoring table has to be placed at 0x0, but U-Boot on MX23/MX28
starts from RAM, so the vectoring table at 0x0 is not present. Craft
code that will be placed at 0x0 and will redirect interrupt vectoring
to proper location of the U-Boot in RAM.
Signed-off-by: Marek Vasut <marex@denx.de>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Replace all relocate_code routines from ARM start.S files
with a single instance in file arch/arm/lib/relocate.S.
For PXA, this requires moving the dcache unlocking code
from within relocate_code into c_runtime_cpu_setup.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Simon Glass <sjg@chromium.org>
Add support for following features:
- nand boot, with PMECC 2bit ECC for 512 bytes sector
- SPI flash boot
- SD card boot
- LCD support
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[fix -Wimplicit-function-declaration for at91_lcd_hw_init()]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
this is needed to bring UART0 out of reset but this function
currently only exists for dm644x/355/365/646x when da850 (at
least am1808 also need it).
Signed-off-by: Eric Bénard <eric@eukrea.com>
This function turns on the LCDIF clock and configures it's frequency. The
dividers settings are calculated within the function and the current
implementation should be fast and accurate.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The u-boot-imx23.bd and u-boot-imx28.bd need to be preprocessed, otherwise
they have issues with out-of-tree build where elftosb tool couldn't sometimes
find the u-boot.bin and spl/u-boot-spl.bin .
Preprocess these .bd files with sed and insert full path to u-boot.bin and
spl/u-boot-spl.bin to prevent this issue. Moreover, to avoid adding more
churn into main Makefile, move all this preprocessing and u-boot.sb generation
into CPU directory instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
The VDDMEM ramped up in very weird way as it was horribly misconfigured.
Instead of setting up VDDMEM in one swipe, let it rise slowly the same
way as VDDD and VDDA in spl_power_init.c and then only clear ILIMIT before
memory gets inited. This makes sure the VDDMEM rises sanely, not jumps up
and down as it did till now.
The VDDMEM prior to this change did this:
2V0____ .--------2V5
| `--'
0V____|
The VDDMEM now does this:
2V0_____,-----------2V5
/
0V__|
Moreover, VDDIO on MX23 uses 25mV steps while MX28 uses 50mV steps,
fix this difference too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Put an explanation in the source code as to why some DDR registers do not
need to be configured.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
After the recent fixes in the mx23 DDR setup, it is safe to operate DDR voltage
at the recommended 2.5V voltage level again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
FSL bootlets code set the PORT_PRIORITY_ORDER field of register HW_EMI_CTRL
as 0x2, which means:
PORT0231 = 0x02 Priority Order: AXI0, AHB2, AHB3, AHB1
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
HW_DRAM_CTL27, HW_DRAM_CTL28 and HW_DRAM_CTL35 are not initialized as per
FSL bootlets code.
mx23 Reference Manual mark HW_DRAM_CTL27 and HW_DRAM_CTL28 as "reserved".
HW_DRAM_CTL8 is setup as the last element.
So skip the initialization of these DRAM_CTL registers.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
On mx23 there is no 'DRAM init complete' in register HW_DRAM_CTL18.
Remove this erroneous setting.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Delete all occurrences of hang() and provide a generic function.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Modify check around puts() in hang.c slightly]
Signed-off-by: Tom Rini <trini@ti.com>
commit 5c2f444c9 (mxs: Reset the EMI block on mx23) changed the DDR voltage
level, which causes mx23evk to fail to load a kernel.
Put back the original values, so that mx23evk can boot a kernel again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
This patch moves the following functions into the imx-common
directory:
- mxs_wait_mask_set()
- mxs_wait_mask_clr()
- mxs_reset_block()
These are currently used by i.MX28. But the upcoming GPMI NAND port
for i.MX6 will also use these functions. So lets move them to a
common location to re-use them.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
The following headers are moved to a i.MX common location:
- regs-common.h
- regs-apbh.h
- regs-bch.h
- regs-gpmi.h
- dma.h
This way this header can be re-used also by other i.MX platforms.
For example the i.MX6 which will need it for the upcoming NAND
support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Let all ARM linker scripts handle properly -ffunction-sections
and -fdata-sections. This will be useful for future changes in order to create
symbol-specific sections in common .S files.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Commit e05e5de7fa made the 2 1st parameters of
ARM's relocate_code() useless since it moved the code handling them to crt0.S.
So, drop these parameters.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This also fixes support for mx31pdk and tx25, which had been broken by commit
e05e5de7fa.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Automatically build the 'u-boot.imx' (i.e. imx header + u-boot.bin) and 'SPL'
(i.e. imx header + u-boot-spl.bin) make targets for all imx processors
supporting this header, so for arm926ejs, arm1136 and armv7. Some combinations
were missing.
At the same time, fix the build of SPL targets not supporting the imx header on
arm1136. For arm1136, the 'SPL' make target was forced to build in all cases if
CONFIG_SPL_BUILD was defined, even for non-imx platforms or imx setups without
an imx header.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Use __image_copy_end instead of __bss_start for the end of the image to
relocate. This is the same as commit 033ca72, but applied to all ARM start.S.
This is a more appropriate symbol naming for an image copy & relocate feature,
and this also saves a useless copy of data put between __image_copy_end and
__bss_start in linker scripts (e.g. relocation information, or MMU
initialization tables used only before jumping to the relocated image).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Commit e05e5de7fa made ARM's relocate_code()
return to its caller, but it did not update its declaration accordingly.
Fixing this function declaration fixes dropped C code following calls to
relocate_code().
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
_TEXT_BASE must be set to CONFIG_SPL_TEXT_BASE for generic SPL, and to
CONFIG_SYS_TEXT_BASE for non-SPL builds.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: Tom Rini <trini@ti.com>
The function get_timer() should return time in ms and CONFIG_SYS_HZ
should be set to 1000 by default. Fix both of these items.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
'bool' is defined in random places. This patch consolidates them into a
single header file include/linux/types.h, using stdbool.h introduced in C99.
All other #define, typedef and enum are removed. They are all consistent with
true = 1, false = 0.
Replace FALSE, False with false. Replace TRUE, True with true.
Skip *.py, *.php, lib/* files.
Signed-off-by: York Sun <yorksun@freescale.com>
Currently the following kernel hang happens when loading a 2.6.35 kernel from
Freeescale on a mx28evk board:
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registered
mxs_cpu_init: cpufreq init finished
...
Loading the same kernel using the bootlets from the imx-bootlets-src-10.12.01
package, the hang does not occur.
Comparing the DDR2 initialization from the bootlets code against the U-boot
one, we can notice some mismatches, and after applying the same initialization
into U-boot the 2.6.35 kernel can boot normally.
Also tested with 'mtest' command, which runs succesfully.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Marek Vasut <marex@denx.de>
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end. We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.
Conflicts:
arch/arm/cpu/ixp/u-boot.lds
arch/arm/cpu/u-boot.lds
arch/arm/lib/Makefile
board/actux1/u-boot.lds
board/actux2/u-boot.lds
board/actux3/u-boot.lds
board/dvlhost/u-boot.lds
board/freescale/mx31ads/u-boot.lds
doc/README.scrapyard
include/configs/tegra-common.h
Build tested for all of ARM and run-time tested on am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
Note this is a tree-wide change affecting multiple architectures.
At present we use __bss_start, but mostly __bss_end__. This seems
inconsistent and in a number of places __bss_end is used instead.
Change to use __bss_end for the BSS end symbol throughout U-Boot. This
makes it possible to use the asm-generic/sections.h file on all
archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Many SPL linker scripts needlessly include linker lists (aka LGAs).
Remove them whenever possible; keep it only in the seven am335x_evm
variants (am335x_evm, am335x_evm_uart[1-5], am335x_evm_spiboot),
where there is actual content in output section .u_boot_list.
This commit keeps all u-boot.bin and u-boot-spl.bin in ARM targets
byte-identical.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
As the CPU name is not configurable, using CPU string directly
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Local macros apply to both iMX23 and iMX28. This patch renames local
macros with attribute MX28 to MXS.
Signed-off-by: Fadil Berisha <f.koliqi@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch add timer support to i.MX23 and complete bit fields and values
on regs-timrot.h.
Testet on imx23-olinuxino board.
Signed-off-by: Fadil Berisha <f.koliqi@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Add a comment about the tRAS lockout setting of HW_DRAM_CTL08 to
enable the 'Fast Auto Pre-Charge' found in the memory chip. The
setting is applied after memory initialization and it is worth
document it.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The power switch option is compatible with i.MX23 and i.MX28 so the
configration option needs to reflect it. We choose
'CONFIG_SPL_MXS_PSWITCH_WAIT' for the option name.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
This patch streamlines the differences between the MX23 and MX28 by
implementing a few helper functions to handle different DMA channel
mapping, different clock domain for SSP block and fixes a few minor
bugs.
First of all, the DMA channel mapping is now fixed in dma.h by defining
the actual channel map for both MX23 and MX28. Thus, MX23 now does no
longer use MX28 channel map which was wrong. Also, there is a fix for
MX28 DMA channel map, where the last four channels were incorrect.
Next, because correct DMA channel map is in place, the mxs_dma_init_channel()
call now bases the channel ID starting from SSP port #0. This removes the
need for DMA channel offset being added and cleans up the code. For the
same reason, the SSP0 offset can now be used in mxs_dma_desc_append(), thus
no need to adjust dma channel number in the driver either.
Lastly, the SSP clock ID is now retrieved by calling mxs_ssp_clock_by_bus()
which handles the fact that MX23 has shared SSP clock for both ports, while
MX28 has per-port SSP clock.
Finally, the mxs_ssp_bus_id_valid() pulls out two implementations of the
same functionality from MMC and SPI driver into common code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The real reason for memory instability was the fact that the EMI block
was gated and not reset throughout the boards' operation. This patch
resets the EMI block properly while also reverts the memory voltage bump.
The memory stability issues were caused by the EMI not being reset properly
and thus there is no longer need to run the memory at higher voltage than
it ought to run at.
This partly reverts 8303ed128a .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The issue got introduced in a cleanup by Manjunath Hadli in commit
826e99136e. The eth_getenv_enetaddr_by_index
method will validate the MAC addr and if none is set in the environment
0 will be returned. Set the MAC from the eeprom if no valid address
is found in environment.
Signed-off-by: Holger Hans Peter Freyther <holger@freyther.de>
When calling 'make u-boot.imx' the build were failing as it were
expecting the full path for the file; this regression has been
included by commit 71a988a (imximage.cfg: run files through C
preprocessor).
The direct references for u-boot.imx were replaced by $(obj) as
config.mk handles the proper setting of it making it set to $(OBJTREE)
when required.
The build has been test using:
- ./MAKEALL -s mx5 -s mx6
- make u-boot.imx
- make O=/tmp/build
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Using the __weak annotation can make the code cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
The memory power supply on MX23 didn't pump out enough juice into
the DRAM chip, thus caused occasional memory corruption. Fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
The '#' used as comments in the files cause the preprocessor
trouble, so change to /* */.
The mkimage command which uses this preprocessor output
was moved to arch/arm/imx-common/Makefile
.gitignore was updated to ignore .cfgtmp files.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
The MX23 has different handling of the SSP clock and GPMI NAND clock sources,
add necessary quirks into the clock code to properly handle these.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The memory init is slightly different on MX23, thus split the memory
init for mx23 and mx28 into different functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The power block on MX23 must first be ungated before it can be operated.
Add function to MXS power init that ungates it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
For i.MX23 we need to pass imx23 as elftosb param.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This adds the boot mode support for i.MX23 processors.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add information to identify i.MX23 chips and its known revisions.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Create function which converts SSP bus number to SSP register pointer.
This functionality is reimplemented multiple times in the code, thus
make one common implementation. Moreover, make it a switch(), since the
SSP ports are not mapped in such nice linear fashion on MX23, therefore
having it a switch will simplify things there.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
This saves stack and code memory for local copy, and
consumes initialized data memory. For 22 of the 29
kirkwood-based boards, this results in a global saving
of about 30 bytes. For 7 of them, it results in an
increase of 6 to 14 bytes.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Move all the C runtime setup code from every start.S
in arch/arm into arch/arm/lib/crt0.S. This covers
the code sequence from setting up the initial stack
to calling into board_init_r().
Also, rewrite the C runtime setup and make functions
board_init_*() and relocate_code() behave according to
normal C semantics (no jumping across the C stack any
more, etc).
Some SPL targets had to be touched because they use
start.S explicitly or for some reason; the relevant
maintainers and custodians are cc:ed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This commit merges branches from samsung, imx and tegra
meant to fix merge issues between u-boot/master and
u-boot-arm/master, as well as a few manual merge fixes.
This algorithm computes the values of TIMING{0,1,2} registers for the
MX28 I2C block. This algorithm was derived by using a scope, but the
result seems correct.
The resulting values programmed into the registers do not correlate
with the contents in datasheet. When using the values from the datasheet,
the I2C clock were completely wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
The reset procedure works on watchdog timer while before it was modifying
TIMER_1 registers.
Tested on DM365.
Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Use a generic 'dram_vals[]' array that has the full initialization
sequence and rename the initialization method so it doesn't has a
frequency on its name.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The MXS SPL didn't mark local functions "static". Fix it. This also makes the
SPL smaller by roughly 300 bytes.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
The memory setup code adjusted the VDDD voltage. Remove this adjustment
and configure the VDDD voltage correctly in the power supply setup code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Implement common function to setup the VDDIO, VDDD and VDDA voltage.
Right now, there are two almost identical functions to setup VDDIO
and VDDD, which is prone to breakage. Pull out the differences into
constant structure and pass them as an argument to the common function.
Moreover, the function has almost identical loops for setting higher
and lower VDDx voltage. Merge these two loops.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
The command declaration now uses the new LG-array method to generate
list of commands. Thus the __u_boot_cmd section is now superseded and
redundant and therefore can be removed. Also, remove externed symbols
associated with this section from include/command.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Add section for the linker-generated lists into all possible linker
files, so that everyone can easily use these lists. This is mostly
a mechanical adjustment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
The MMC driver appropriate for the i.MX25 is fsl_esdhc, which has nothing to do
with mxcmmc.
Also, each eSDHC instance has a dedicated clock, so gd->sdhc_clk must be set
accordingly. This is good for the case only a single SDHC instance is used
(initialization made with fsl_esdhc_mmc_init()). A future patch will fix the
multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
The FEC is the only SoC Ethernet support available on i.MX25, so define
cpu_eth_init() only for it instead of returning a misleading success code.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Use the standard mxc_get_clock() instead of exporting internal functions and
using literal constant values.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
mxc_get_clock(MXC_FEC_CLK) should return the IPG clock, not the AHB clock.
Also, imx_get_fecclk() was correct but reimplemented the calculation of the IPG
clock, so remove the duplicated code.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Avoid possible overflow in clock calculations, and do not waste calls to lldiv()
to divide simple ulongs.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
The MFN bit-field of the PLL registers represents a signed value. See the
reference manual.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
tested on a MCIMX257CJM4A which now reports :
CPU: Freescale i.MX25 rev1.2 at 399 MHz
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Remove the empty bodies from serial_* functions from MXS SPL code.
These empty implementations are now in common/serial.c instead so
declaring them also in the SPL code would cause a colision once
serial multi is enabled unconditionally.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Under option -munaligned-access, gcc can perform local char
or 16-bit array initializations using misaligned native
accesses which will throw a data abort exception. Fix files
where these array initializations were unneeded, and for
files known to contain such initializations, enforce gcc
option -mno-unaligned-access.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Switch to usign call cc-option for -mno-unaligned-access as
Albert had done previously as that's really correct]
Signed-off-by: Tom Rini <trini@ti.com>
When the u-boot address of destination equal to __start,
no relocation. relocation offset(r9) = 0.
Signed-off-by: Zhong Hongbo <bocui107@gmail.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Size of the SDRAM chips might differ between any two (otherwise
identical) instances of the same board.
So add a function kw_sdram_size_adjust() which reads out the current
ram size for a given bank, and adjusts the Kirkwood's SDRAM window size
register accordingly.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Some boards might be equipped with different SDRAM configurations.
When that is the case, CPU CS Window Size Register (CS[0]n Size)
should be set to the biggest value through board.cfg file; then its
value can be fixed at runtime according to the detected SDRAM size.
Therefore, implement kw_sdram_bs_set().
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Marek Vasut <marex@denx.de>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
Remove the defines and do this with a C-struct.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Marek Vasut <marex@denx.de>
Acked-By: Prafulla Wadaskar <Prafulla@marvell.com>
- Convert the non-relocation part of board_init_f to spl_board_init, turn on CONFIG_SPL_BOARD_INIT in the configs.
- Remove duplicated code.
- Add spl_boot_device() that returns the statically chosen boot device.
Signed-off-by: Tom Rini <trini@ti.com>
Use proper struct-based access for this register in the SPL code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Orion5x did not actually write GPIO output values
or input polarities, and ED Mini V2 had bad or
missing values for GPIO settings.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
For representing a timeout value, it makes more sense to pass it as
'unsigned int'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
The DRAM initialization, after SPL has complete, is exactly the same
for all mxs SoCs so we should name it accordinly.
The following boards has been changed:
* apx4devkit
* m28evk
* mx28evk
* sc_sps_1
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
The internal Ethernet controller is only available on i.MX28
processors so it needs to use CONFIG_MX28 guardian to avoid having
this code called in others.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
The elftosb call needs to use a target param specific for i.MX28. This
patch allow for later addition of i.MX233.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
Now that the main i.MX features work fine with dcache enabled, enabled it by
default if CONFIG_SYS_DCACHE_OFF is not defined.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Move some function calls to a more appropriate place, so they're
called only when needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The SPL doesn't need the CP15 reconfiguration, as that's what the
BootROM does for us already. Moreover, when the CP15 is reconfigured
and the code returns control to BootROM, the USB boot works no more.
Remove the code and allow [1] to work properly as well.
[1] http://git.bfuser.eu/?p=marex/mxsldr.git;a=summary
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The sys_proto.h functions (except the boot modes) are compatible with
i.MX233 and i.MX28 so we use 'mxs' prefix for its methods.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The iomux header is included on sys_proto.h so to avoid SoC specific
header inclusion.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
We can safely use the same reset code written in C for both Davinci and
C6X platforms. In addition the C version of the code is marginally
smaller on Davinci.
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Also enable the ohci port on hawkboard. These additions result in an
increased u-boot size -- adjust the same accordingly in the board's
config.
Move the usb header for da8xx platforms under arch-davinci.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
This gets us rid of duplication of the same file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
If VDDIO has a brownout, then the VDD5V_GT_VDDIO becomes unreliable
but this wasn't clear on code so a comment has been added to clarify
it.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
As the register accessing mode is the same for all i.MXS SoCs we ought
to use 'mxs' prefix intead of 'mx28'.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Most code can be shared between i.MX23 and i.MX28 as both are from
i.MXS family; this source directory structure makes easy to share code
among them.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
The mx28 prefix has been added to the initialization data and function
so it is clear by which SoC it is used as i.MX233 will have a specific
one. While on that, we also change it to static.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
The information now is gathered from HW_DIGCTL_CHIPID register and
includes the chip modem and revision on the output.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Markus Hubig <mhubig@imko.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add at91sam9x5ek board support, this board support the following SoCs
AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35
Using at91sam9x5ek_nandflash to configure for the board
Now only supports NAND with software ECC boot up
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[move MAINTAINERS entry to right place]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
For the DA8xx family of SoCs, the set_cpu_clk_info() function was not
initialising the DSP frequency, leading to 'bdinfo' command output such as:
[...snip...]
ARM frequency = 300 MHz
DSP frequency = -536870913 MHz
DDR frequency = 300 MHz
This commit provides a separate implementation of set_cpu_clk_info() for
the DA8xx SoCs that initialises the DSP frequency to zero (since
currently the DSP is not enabled by U-Boot on any DA8xx platform). The
separate implementation is justified because there is no common code
between DA8xx and the other SoC families. It is now much easier to
understand the flow of the two separate functions.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Hadli, Manjunath <manjunath.hadli@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Replace a magic number for the DDR2/mDDR PHY clock ID with a proper
definition. In addition, don't request this clock ID on DA830 hardware,
which does not have a DDR2/mDDR PHY (or associated PLL controller).
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
follow section 15.2.13.1 (Initializing Following Device Power Up or Reset) of
OMAP-L138 DSP+ARM Processor Technical Reference Manual
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
DA850/OMAP-L138 does not support strict MMC/SD boot mode. SPL will
be in SPI flash and U-Boot image will be in MMC/SD card. SPL will
do the low level initialization and then loads the u-boot image
from MMC/SD card.
Define CONFIG_SPL_MMC_LOAD macro in the DA850/OMAP-L138
configuration file to enable this feature.
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
initialize baudrate, flags, data and serial initialization,
only when CONFIG_SPL_LIBCOMMON_SUPPORT is defined.
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
This patch adds support for MMC/SD on DA850/OMAP-L138.
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
This patch moves all bootcount implementations into a common
directory: drivers/bootcount. The generic bootcount driver
is now usable not only by powerpc platforms, but others as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
No need to define CONFIG_ARCH_CPU_INIT.
All mx28 based boards should use arch_cpu_init().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
This patch adds SPL support for SPEAr600. Currently only SNOR
(Serial NOR) flash support is included. Other boot devices
(NAND, MMC, USB ...) may be added with later patches.
Tested on the STM SPEAr600 evaluation and x600 SPEAr600 boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
UART in u-boot intends to run on 48MHz clock supplied by USB PLL.
Explicitly select the intended clock source.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Earlier, architecture specific init code was mixed with board initialization
code in board/spear/... This patch updates architecture support for SPEAr in
latest u-boot and prints the SoC information.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
If a second non NULL argument is given to the kirkwood_mpp_conf
function, it will be used to store the current configuration of the MPP
registers. mpp_save must be a preallocated table of the same size as
mpp_list and it must be zero terminated as well.
A later call to kirkwood_mpp_conf function with this saved list as first
(mpp_conf) argment will set the configuration back.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This function can be overridden at run-time and allows implementors
of new boards based on the i.MX28 chip to fine-tune the memory params.
It is possible to write into the dram_vals array because when the SPL
runs, it is located SRAM. Therefore the location is writable. There is
no possibility of these data to be read-only.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Previously, only the low 5 bits (NCH) were being transfered
from DDRVTPR to DDRVTPIOCR, the bits 5-9 where zeroed.
VTP_RECAL should be bit 15, not 18.
The only mainline board affected by this change is davinci_sonata.
The other Davinci boards define CONFIG_SKIP_LOWLEVEL_INIT.
However, if the program that loads u-boot on these boards
copied the code from u-boot, they will need fixed as well.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Please get tested by acks before applying, where tested by
means an overnight memory test.
Thanks
Troy
Do not define serial_putc() and serial_puts() calls if
CONFIG_SPL_SERIAL_SUPPORT is set.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
This code is part of battery boot support for i.MX28.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
If the LCD controller is on before the CPU goes into reset, the traffic on LCDIF
data pins interferes with the BootROM's boot mode sampling. So shut the
controller down.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Pass memory size from SPL via structure located in SRAM instead of SCRATCH
registers. This allows passing more data about boot from SPL to U-Boot, like the
boot mode pads configuration.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
This solves issues when larger amount of DRAM is used, like 256MB.
Behave the same in case of CPU bypass as we do in case of EMI
bypass, but wait 15 ms. We need to wait until the clock domain
stabilizes.
This issue seemed to have been caused by not waiting after frobbing
with the CPU bypass, it was unrelated to memory, but had a direct
impact, causing trouble. This was yet another X-File of the
imx-bootlets, sigh. The conclusion is, trying a semi-random delay
(there is delay after the EMI bypass change), the issue is fixed.
Another possible explanation is that we do not do the "simple memory
test" FSL does in their imx-bootlets (1000 R/W cycles to/from piece of
the memory, while also outputing something on the serial port). This
might have caused the similar delay in the imx-bootlets and therefore
they didn't need to add this explicitly.
For now, this seems good fix enough, but to me, whole that memory
init code in imx-bootlets is completely flunked and it'd need deeper
investigation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Defining CONFIG_FSL_ESDHC brings in a call to get_clocks, so let's
implement get_clocks function. This is how it seems to be implemented
elsewhere.
Signed-off-by: Timo Ketola <timo@exertus.fi>
Acked-by: Stefano Babic <sbabic@denx.de>
This reverts commit 69d26d09de.
Apparently, this commit got mainline only because of out-of-tree
port and causes breakage on board that is mainline. Revert.
Reason:
* The OOT board has 512MB of DRAM, enabling this additional address
line enabled it to work fine with 512MB of RAM.
* Every mainline port has max. 256MB of DRAM, therefore this revert
has no impact on any mainline port
* Though this caused a problem with new M28 board with 256MB of DRAM
where the chips are wired differently. The patch-to-be-reverted
caused the DRAM to behave like this:
[128MB chunk #1][128MB chunk #1 again][128MB chunk #2][128MB chunk #2 again]
Therefore to retain the current one-memory-init-rules-them-all situation,
revert this patch until another board emerges and will actually be pushed
mainline that needs different setup.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
This change adds initial support for NXP LPC32x0 SoC series.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
We certainly don't want the compiler to reorganise the code for dcache flushing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Stefano Babic <sbabic@denx.de>
This fixes the issue where mxs_dma_init() was called either twice or never,
without introducing any new init hooks.
The idea is to allow each and every device using the APBH DMA block to
configure and request only the channels it uses, instead of making it call init
for all the channels as is now.
The common DMA block init part, which only configures the block, is then called
from CPUs arch_cpu_init() call.
NOTE: This patch depends on:
http://patchwork.ozlabs.org/patch/150957/
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Misaligned warnings are useful to debug faulty drivers.
A misaligned warning is printed also when the driver
is correct - use debug() instead of printf().
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Each cpu directory currently has its own .lds file. This is only needed
in most cases because the start.o file is in a different subdir.
Now that we can factor out this difference, we can move most cpus over
to the common .lds file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Instead of compiling the function and using the result as a constant, simply use
the constant.
NOTE: This patch works around bug:
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=52546
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cut down the VDDIO/VDDA regulator stabilization delays to 500 uS. That should be
enough according to the datasheet and bootlets.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Robert Deliën <robert@delien.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
Enables all fourteen address lines for DRAM
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
This patch fixes erroneous 32-bit access to registers
hw_clkctrl_frac0 and hw_clkctrl_frac1.
Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
This patch renames mx28_register to mx28_register_32 in order to
prepare for the introduction of an 8-bit register, mx28_register_8.
Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
This patch replaces the use of magice numbers for scratch register
addresses with earlier defined register definitions.
Signed-off-by: Robert Delien <robert@delien.nl>
All boards are using the gen_atmel_mci driver now, so no need
to carry the old driver around.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Boards can select either the 'built-in' parser or the hush parser. We
should not call builtin_run_command() if we are using the hush parser.
We use run_command() instead, since it knows how to call the correct
parser.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The current run_command() is only one of the parsing options - the other
is hush. We should not call run_command() when the hush parser is being
used. So we rename this function to better explain its purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
In commit 2d575e4685 a separate header
file was introduced for the DM6467T EVM, include/configs/davinci_dm6467Tevm.h.
The substantial difference between the davinci_dm6467evm and the
davinci_dm6467Tevm configuration is a single bit in the hardware revision
that is passed to the Linux kernel and davinci_dm6467evm has
REFCLK_FREQ = 27000000 where as davinci_dm6467Tevm.h has a
REFCLK_FREQ = 33000000.
This patch removes include/configs/davinci_dm6467Tevm.h. Instead the
include/configs/davinci_dm6467evm.h configuration is used for DM6467T EVMs and
renamed CFG_REFCLK_FREQ to CONFIG_REFCLK_FREQ and CONFIG_REFCLK_FREQ is defined
in boards.cfg.
Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Tom Rini <trini@ti.com>
check for the return status for eth_getenv_enetaddr_by_index()
and eth_setenv_enetaddr() functions and print appropriate message
on failure.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This patch fixes booting i.MX28 CPUs via USB download.
In this mode the CPU's bootrom implements a USB HID device that
accepts a bootstream.
When downloading the bootstream via USB, first the SPL code is
received and executed. Then the u-boot image is received and
called.
The USB bootmode is interrupt driven.
This patch fixes two things:
1) The ARM's fast interrupt mode is disabled when the SPL code
has been run. So save and restore the CPSR register.
2) Save and restore c1 control register: the exception vector
location needs to be set back to bootrom space to make the USB
interrupts work again. The SPL code needs to change this
option for the ram size probing.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
The DC power STS shouldn't be checked if booting off 5V supply.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Robert Deliën <robert@delien.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
This patch moves hawkboard to the new spl infrastructure from the
older nand_spl one.
Removed the hawkboard_nand_config build option -- The spl code now
gets compiled with hawkboard_config, after building the main u-boot
image, using the CONFIG_SPL_TEXT_BASE. Modified the README.hawkboard
to reflect the same.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
The V bit of the c1 register of CP15 should not be cleared on DA850
SoCs since they have no valid memory at 0x00000000. This patch
introduces a configuration option CONFIG_SYS_EXCEPTION_VECTORS_HIGH
that allows setting the correct value for the V bit.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Reported-by: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
The current implementation invalidates the data cache before turning it
off and causes problems on the hawkboard. See the discussion in
http://lists.denx.de/pipermail/u-boot/2012-January/115212.html
According to the ARM926EJ-S Technical Reference Manual, the cache should
be flushed instead.
Also fix the comments to match code.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Rebased and corrected commit message.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
This patch reverts commit ca4b55800e
"arm, arm926ejs: always do cpu critical inits" since it impacts all
arm926ejs based configurations and caused problems, e.g., with
the hawkboard.
Instead the patch removes the CONFIG_SKIP_LOWLEVEL_INIT defines
from the board configurations that need low level initialization.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
The low level initialization code in
arch/arm/cpu/arm926ejs/davinci/lowlevel_init.S was written for
DM644X SoCs only. This patch makes the lowlevel_init function in this
file a dummy function for SoCs other than DM644X.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Tom Rini <trini@ti.com>
Cc: Sergey Kubushyn <ksi@koi8.net>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
add support for printing various clock frequency info found
in SOC such as ARM core frequency, DSP core frequency and DDR
frequency as part of bdinfo command.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
remove the macro CONFIG_DISPLAY_CPUINFO as it is no longer
required. This is because clock info will be printed as part
'bdinfo' command and also remove support print_cpuinfo() as it will
no longer be called.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
after http://patchwork.ozlabs.org/patch/136415/ was applied. All Marvell
build fails with below error
common/libcommon.o: In function `cread_line':
/home/uboot/src/u-boot-arm/common/main.c:717: undefined reference to `get_ticks'
/home/uboot/src/u-boot-arm/common/main.c:717: undefined reference to `get_tbclk'
/home/uboot/src/u-boot-arm/common/main.c:720: undefined reference to `get_ticks'
The same is fixed for Kirkwood, ARMADA100, pantheon and orion5x SoCs
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
The decompressor expects the L2 cache to be disabled. This fixes booting
some kernels, which have CONFIG_ARM_PATCH_PHYS_VIRT enabled.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Wolfgang Denk <wd@denx.de>
Showing CPU frequency during boot is useful information.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This patch modifies mxcmmc.c to be used
not only by i.MX27 but also by i.MX31 boards.
Both use the same SD controller, but have different
clock set-ups.
The i.MX27 imx_get_XXXclock functions are made static to
generic.c and a public mxc_get_clock() function
is provided. Pins, base address and prototypes for
an i.MX31 specific board_init_mmc() are provided.
Some of the i.MX27 clock getters are unused and marked
as such to avoid warnings (./MAKEALL -s mx27), but
the code was left in for future use.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
The Buffer Logic of VPSS is Not Reset by System Reset Pin, see
http://www.ti.com/lit/er/sprz316b/sprz316b.pdf chapter Advisory 1.2.1
on page 9. Add workaroundcode proposed in the errata.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <tom.rini@gmail.com>
The OMAP-L138 has a pre-divider available on PLL0.
Add support to da850_lowlevel.c for configuring PLL0's pre-divider. This is
to achieve certain OPP's -- e.g. the 372MHz OPP used also by Linux.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: Christian Riesch <christian.riesch@omicron.at>
CC: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
There are 2 locations in the power init code for the mx28 where IRQs are not being cleared because incorrect methods to clear those bits were being used. This was causing my board to get stuck waiting for POWER_CTRL_VDD5V_DROOP_IRQ to clear. Using the correct method to clear the IRQs fixes it.
Signed-off-by: Zach Sadecki <zach@itwatchdogs.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Let dram_init function be a common function, so that other mx28 boards
can reuse it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Let imx_get_mac_from_fuse function be a common function, so that other
mx28 boards can reuse it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add multi-FEC support for imx_get_mac_from_fuse by passing dev_id as a parameter.
This feature is important on mx28 SoC for example that has two FEC ports.
Cc: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Config options for OMAP are not used with i.MX28 so remove dead code.
Signed-off-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This patch fixes a build warning for the cam_enc_4xx board introduced by
commit d6ec0c0dfc70447cf615ae80a952da81f73f16b4:
spl.c:35:13: warning: 'gdata' defined but not used
spl.c:36:13: warning: 'bdata' defined but not used
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
This code adds an SPL for booting from SPI flash on DA850 SoCs.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Commit 2f3427c added noop cache functions implementation for arm926ejs
to fix compilation of drivers depending on these functions (DaVinci
EMAC in particular).
Unfortunately, the bug was introduced: noop implementation calls
dcache_disable which calls flush_dcache_all which in turn calls
dcache_disable thus creating an infinite loop.
This patch removes noop implementation for flush_dcache_all, we already
have default one in arch/arm/lib/cache.c and it should be used instead.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Tested-by: Matthias Weisser <weisserm@arcor.de>
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
The current way memsize.c is built just made a symlink into the directory
with SPL and then compiled it like any other file there. This was bad as that
broke the out-of-tree build.
The new way introduced in this patch uses the standard spl/Makefile methods
(CONFIG_SPL_LIBCOMMON_SUPPORT / CONFIG_SPL_LIBGENERIC_SUPPORT) to let files in
common/ be built. Because common/Makefile says memsize.c is always built (SPL
and non-SPL build), this fixes our issue with memsize.c out-of-tree build.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This moves SPL to common location so it can be reused by multiple boards. Also,
this commit adjusts M28 SoM to avoid breakage due to the move.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
move the board/davinci/common/misc.c file to
arch/arm/cpu/arm926ejs/davinci/misc.c, so all
davinci boards can use this functions.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Christian Riesch <christian.riesch@omicron.at>
This patch replaces the pinmux configuration code in
arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c by the code from
arch/arm/cpu/arm926ejs/davinci/pinmux.c.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
Up to now nearly every davinci board has separate code for the
definition of pinmux configurations. This patch adds pinmux
configurations for the DA850 SoCs to the arch tree which may later
be used for all DA850 based boards.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Heiko Schocher <hs@denx.de>
always do the cpu critical inits in cpu_init_crit,
and only jump to lowlevel_init, if CONFIG_SKIP_LOWLEVEL_INIT
is not defined.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Added noop implementation for dcache operations that will buzz
about missing real implementation and disable the dcache.
This fixes compilation of DaVinci EMAC driver on arm926ejs.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
DaVinci EMAC is found not only on DaVinci SoCs but on some OMAP3 SoCs
also. This patch moves common defines from arch-davinci/emac_defs.h to
drivers/net/davinci_emac.h
DaVinci specific PHY drivers hacked to include the new header. We might
want to switch to phylib in future.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
This patch fixes the clear bss loop for bss sections that have
zero length, i.e., where __bss_start == __bss_end__.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Change my old email address which is no longer valid.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
cpuinfo.c: In function 'print_cpuinfo':
cpuinfo.c:155:6: warning: variable 'system_serial_low' set but not used
[-Wunused-but-set-variable]
cpuinfo.c:154:6: warning: variable 'system_serial_high' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
- Cleanup a lot of fix values, and use defines instead.
- Also make some values configurable through the board config
file.
- delete the NAND_SPL code for da850, as it is not used actually
- remove the asm code
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch introduces proper ARM vector handling for i.MX28 CPU. This issue
wasn't addressed because the interrupts weren't enabled on any ARMv5 core,
therefore the issue wasn't noticed earlier.
In previous implementation, the vectoring code used by i.MX28 CPU when an
exception happened was that of the SPL. With this change, the branch target when
an exception happens can be reconfigured by U-Boot.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Taken from Linux kernel with minor modifications:
commit bf985969e27b507f734435a99df8bf745a3dbb2b
Author: Shawn Guo <shawn.guo@freescale.com>
Date: Mon Dec 20 22:57:43 2010 +0800
ARM: mxs: Add iomux support
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
This allows the SPL to avoid compiling in the CPU support code.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
da850_ddr_setup() expects the BOOTUNLOCK bit to be set in
If BOOTUNLOCK is not set in this define, several configuration
bits will not be writeable and the code will not work.
Since the BOOTUNLOCK and TIMUNLOCK bits are not configuration options
but access control bits, this patch changes the code to work
irrespective of the value of these bits in CONFIG_SYS_DA850_DDR2_SDBCR.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Paulraj Sandeep <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The LPSC functions defined in
arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c
are replaced by those already defined in
arch/arm/cpu/arm926ejs/davinci/psc.c.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Paulraj Sandeep <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Rename arch/arm/cpu/arm926ejs/davinci/am1808_lowlevel.c and
arch/arm/include/asm/arch-davinci/am1808_lowlevel.h to da850_lowlevel.c
and da850_lowlevel.h since they apply not only to the AM1808 SoC
but to all DA850 chips. The function names and #defines are changed
likewise.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Paulraj Sandeep <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
used for booting (for example) from NAND using spl code.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This generated file does not belong in the tree -> punt.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
U-Boot Makefiles contain a number of tests for compiler features etc.
which so far are executed again and again. On some architectures
(especially ARM) this results in a large number of calls to gcc.
This patch makes sure to run such tests only once, thus largely
reducing the number of "execve" system calls.
Example: number of "execve" system calls for building the "P2020DS"
(Power Architecture) and "qong" (ARM) boards, measured as:
-> strace -f -e trace=execve -o /tmp/foo ./MAKEALL <board>
-> grep execve /tmp/foo | wc -l
Before: After: Reduction:
==================================
P2020DS 20555 15205 -26%
qong 31692 14490 -54%
As a result, built times are significantly reduced, typically by
30...50%.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Albert Aribaud <albert.aribaud@free.fr>
cc: Graeme Russ <graeme.russ@gmail.com>
cc: Mike Frysinger <vapier@gentoo.org>
Tested-by: Graeme Russ <graeme.russ@gmail.com>
Tested-by: Matthias Weisser <weisserm@arcor.de>
Tested-by: Sanjeev Premi <premi@ti.com>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Macpaul Lin <macpaul@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
To compile TI Davinci SoC support the identical config.mk file from
the cpu directory shall be used.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
remove macro CONFIG_EMAC_MDIO_PHY_NUM and depending macro EMAC_MDIO_PHY_NUM
as they are no longer needed with the support for more than 1 PHYs in davinci
emac driver.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
MDSTAT.STATE occupies bits 0..5 according to all available documentation, so fix
the mask which previously was leaving out the intermediate state indicator bit.
While at it, introduce two #define's for that mask -- unfortunately, we can't
use a single #define as the assembly code can't include <asm/arch/hardware.h>
due to C-specfic constructs in it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
For files like the drivers/serial/serial.c, it must include the
platform file, as the CONFIG_SYS_NS16550_COM1 must reference to
the definition in the platform definition files.
Include the platform definition file in the config file, so that it
would decouple the dependence for the driver files.
Signed-off-by: Lei Wen <leiwen@marvell.com>
For files like the drivers/serial/serial.c, it must include the
platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the
definition in the platform definition files.
Include the platform definition file in the config file, so that it
would decouple the dependence for the driver files.
Signed-off-by: Lei Wen <leiwen@marvell.com>
For files like the drivers/serial/serial.c, it must include the
platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the
definition in the platform definition files.
Include the platform definition file in the config file, so that it
would decouple the dependence for the driver files.
Updated cpu.h to remove build errors for gplugd board (by prafulla)
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
For files like the drivers/serial/serial.c, it must include the platform
file, as the CONFIG_SYS_NS16550_COM1 must reference to the definition in
the platform definition files.
Include the platform definition file in the config file, so that it
would decouple the dependence for the driver files.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Copied wholeheartedly from board/Marvell/guruplug and modified to add support
for SPI NOR flash.
CONFIG_MACH_DREAMPLUG defined in include/configs/dreamplug.h until Linus's
kernel.org tree adds it to mach-types.h. Once it trickles down, the definition
can be removed from include/configs/dreamplug.h.
Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>
Fix checkpatch warning and errors in several i.MX related files.
While at it also address a checkpatch warning at arch/arm/cpu/armv7/mx5/soc.c
regarding the usage of extern in a C file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Seems people fixed their files to use libfoo.o, but didn't actually
update the creation targets to use $(cmd_link_o_target). Update the
rest of the Makefile's found with grep.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Simon Glass <sjg@chromium.org>
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When building the zmx25 target we get:
Configuring for zmx25 board...
generic.c:108: warning: 'get_reset_cause' defined but not used
Fix this warning by defining get_reset_cause only if CONFIG_DISPLAY_CPUINFO is defined.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Result of running the following command to address Wolfgang's
comment about camel case:
for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done
Discussion:
http://patchwork.ozlabs.org/patch/84988/
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
commit 0edf8b5b2f breaks
building on a different directory with the O= parameter.
The patch wil fix this issue, generating always asm-offsets.h before
the other targets.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Wolfgang Denk <wd@denx.de>
Modify clk_get() function in cpu file to work for
multiple PLL controllers.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Rework for AT91SAM9263 SoC, makes it build again.
Based on the work for AT91SAM9260-EK.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <uboot@emk-elektronik.de>
Rework for AT91SAM9RL SoC, makes it build again.
Based on the work for AT91SAM9260-EK.
V4: US->USART, cosmetics
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Bits 0..3 in cs_mask = CS0..CS3 in SPI mode require it to be peripheral
Bits 4..7 in cs_mask = CS0..CS3 in GPIO mode require it to be output
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
In some circumstances, reset_timer_masked() was called be timer_init() in
order to perform architecture specific timer initialisation. In such
cases, the required code in reset_timer_masked() has been moved into
timer_init()
Checkpatch.pl complains about the volatile qualifier in calls to
get_ram_size(). Remove this qualifier in the prototype and in the
calls where it is useless, and leave it only in the function body
where it is needed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
On i.MX27, the asm-offsets.h file is not yet generated as it should be.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
Offsets to registers may be needed in asm code. This patch adds automated
generation of these offsets form C structures.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
mx27_uart_init_pins does the IOMUX setting for UART1 port.
Change the function name to make the UART port number explicit.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch adds an copy of arm926ejs/at91/clock.c to arm920t/at91. The
arm926ejs specialities are removed from arm920t version and vice versa.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Monitor protection region in FLASH did not cover .rel.dyn
and .dynsym sections, because it uses __bss_start to compute
monitor_flash_len. Use _end instead.
Add _end to linker scripts for end of u-boot image
Add _end_ofs to all the start.S.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
