The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
For readability during configuring firewalls, adding k3-security.h file
and including it in k3-binman.dtsi to be accessible across K3 SoCs
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Andes CPU supports cache and TLB ECC.
Enable them by default.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Andes CPU has memboost feature including prefetch,
write-around and non-blocking load. Enable them by default.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Kconfig provides SYS_[I|D]CACHE_OFF config options to switch off caches.
Provide the corresponding implementation to the options.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Extend compatible string to match the latest change in dt binding.
Fixes: 7576ab2fac ("riscv: Add support for AMD/Xilinx MicroBlaze V")
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The power gating feature of pl2 should be enabled as early as possible,
it would be better to put it in SPL stage.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Simon Glass <sjg@chromium.org> says:
This series continues refactoring the bootm code to allow it to be used
with CONFIG_COMMAND disabled. The OS-handling code is refactored and
a new bootm_run() function is created to run through the bootm stages.
This completes the work.
A booti_go() function is created also, in case it proves useful, but at
last for now standard boot does not use this.
This is cmdd (part d of CMDLINE refactoring)
It depends on dm/bootstda-working
which depends on dm/cmdc-working
Use the new bootm/z_run() functions to avoid having to create an
argument list for the stm32prog code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Rather than assigning to the bootm_argv[] array multiple times, use
local variables for the two things that can change and assign them at
the end.
This makes it easier to drop the array eventually.
Tidu up an overly short line while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Rename the function to bootm_run_states() to better indicate ts
purpose. The 'do_' prefix is used to indicate a command processor,
which this is now not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adjust boot_os_fn to use struct bootm_info instead of the separate
argc, argv and image parameters. Update the handlers accordingly. Few
of the functions make use of the arguments, so this improves code size
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
It is useful for sandbox to build as much code as possible. Enable
support for booting various other operating systems. Add the missing
cache functions.
These operating systems do not actually boot on sandbox, of course.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current do_reset() is called from a command context. Add a function
which can be used from anywhere, as is done on ARM. Adjust do_reset()
to call it.
Note that reset_cpu() is normally provided by SYSRESET so make this
declaration conditional on that being disabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Tested-by: Chanho Park <chanho61.park@samsung.com>
The current do_reset() is called from a command context. Add a function
which can be used from anywhere, as is done on ARM.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current do_reset() is called from a command context. Add a function
which can be used from anywhere, as is done on ARM.
This is only needed if CONFIG_SYSRESET is disabled.
Since there are lots of reset functions, this one actually just calls
do_reset(). Future refactoring could correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current do_reset() is called from a command context. Add a function
which can be used from anywhere, as is done on ARM.
Since there are lots of reset functions, this one actually just calls
do_reset(). Future refactoring could correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Angelo Dureghello <angelo@kernel-spcece.org>
The current do_reset() is called from a command context. Add a function
which can be used from anywhere, as is done on ARM.
Signed-off-by: Simon Glass <sjg@chromium.org>
In order for RMOBILE_CPU_TYPE_R9A07G044L to be defined we need to
include <mach/rmobile.h> here.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
In most cases, the architecture global data currently makes use of
assorted linux types, but does not include <linux/types.h> to provide
them. Add <linux/types.h> instead of relying on indirect inclusion.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
In the architecture global data, replace the one case of u32 with
unsigned long. Now, we can drop config.h here but then do need to add it
in two m68k-centric spaces.
Acked-by: Angelo Dureghello <angelo@kernel-space.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We need <linux/types.h> in these files as we reference Linux types.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We need and include <linux/types.h> and this in turn already includes
<asm/types.h>, so drop it here.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove and replace common.h and config.h in sandbox when it's not needed
and add some explicit includes where needed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We need to include <config.h> directly when a file needs to have
something such as CFG_SYS_SDRAM_SIZE referenced as this file is not
automatically globally included and is most commonly indirectly included
via common.h. Remove most cases of arm including config.h directly, but
add it where needed. This includes a few board-specific fixes.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We need to include <config.h> directly when a file needs to have
something such as CFG_SYS_SDRAM_SIZE referenced as this file is not
automatically globally included and is most commonly indirectly included
via common.h. Remove most cases of arc including config.h directly, but
add it where needed. Further clean up the tb100 board config.h file so
that we don't rely on config.h being included there for a value used in
a single place.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
In general terms, we -include include/linux/kconfig.h and so normal
U-Boot code does not need to also #include it. However, for code which
is shared with userspace we may need to add it so that either our full
config is available or so that macros such as CONFIG_IS_ENABLED() can be
evaluated. In this case make sure that we guard these includes with a
test for USE_HOSTCC so that it clear as to why we're doing this.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This change configures Toradex Colibri iMX8X SoM USB
hub to bypass mode, and brings out of the reset state.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
This file is included automatically since quite some time now.
From documentation:
U-Boot automatically looks for and includes a file with updates
to the standard devicetree for your board, searching for them in
the same directory as the main file, in this order:
<orig_filename>-u-boot.dtsi
<CONFIG_SYS_SOC>-u-boot.dtsi
<CONFIG_SYS_CPU>-u-boot.dtsi
<CONFIG_SYS_VENDOR>-u-boot.dtsi
u-boot.dtsi
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
This file is included automatically since quite some time now.
From documentation:
U-Boot automatically looks for and includes a file with updates
to the standard devicetree for your board, searching for them in
the same directory as the main file, in this order:
<orig_filename>-u-boot.dtsi
<CONFIG_SYS_SOC>-u-boot.dtsi
<CONFIG_SYS_CPU>-u-boot.dtsi
<CONFIG_SYS_VENDOR>-u-boot.dtsi
u-boot.dtsi
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Add the TPM device found on the GW72xx revision F PCB.
This hangs off of SPI2, uses gpio1_10 as a CS and gpio1_11 as RST#.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add the TPM device found on the GW72xx revision F PCB.
This hangs off of SPI2, uses gpio1_10 as a CS and gpio1_11 as RST#.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Incorrect registers HW_POWER_VDDIOCTRL, HW_POWER_VDDACTRL
and HW_POWER_VDDDCTRL are used in the current code to disable/enable
brownout interrupts in 'mxs_power_set_vddx()'.
Change register to HW_POWER_CTRL which contains brownout interrupt
enable bits ENIRQ_VDDIO_BO, ENIRQ_VDDA_BO and ENIRQ_VDDD_BO.
Signed-off-by: Cody Green <cody@londelec.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
-----BEGIN PGP SIGNATURE-----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=aBS6
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-next-20231220' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- Add support for new GXL MDIO mux, with driver and Linux DT sync from v6.4
Since implementation of pinctrl driver for T20 Paz00 can switch
to device tree pinmux setup along with remove of board pinmux
and some minor device tree and defconfig tweaks.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used for the Linux
device tree and are set according to the downstream kernel.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used in the Linux
device tree.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used for the Linux
device tree and are set according to the service manual.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used in the Linux
device tree.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Move all existing pinmux and funcmux code into a dedicated folder in
pinctrl to simplify further maintenance.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The existing pinctrl driver available for Tegra SOC is well
designed, but it lacks DM support. Let's add a DM compatible
overlay, which allows use of the device tree, along with preserving
backward compatibility with all existing setups and the ability
to use it in SPL board configuration stage.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
SPL configs are used only by the ARMv7-based Tegra SOC's, so move
SPL_SYSRESET under TEGRA_ARMV7_COMMON selection and enable SPL_DM
since SPL_SYSRESET depends on it.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
PLLD2 is a simple clock (controlled by 2 registers) and appears starting
from T30. Primary use of PLLD2 is as main HDMI clock parent.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
PLLD2 is a simple clock (controlled by 2 registers) and appears starting
from T30. Primary use of PLLD2 is as main HDMI clock parent.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Simple PLL clocks like PLLD2 were omitted since they do not share common
4 register structure with main clocks. Such clocks are containd in simple
PLL group. Only clock_start_pll function supported them. This patch expands
this support on clock_set_rate and clock_get_rate which should make
simple PLL clocks equal to main PLL clocks.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Julien Masson <jmasson@baylibre.com> says:
This patch series add the support for the MediaTek MT8365 EVK Board [1].
Most of the code have been copied/adapted from Linux tag v6.7-rc2.
For now we only enable/test these features:
Boot, UART, Watchdog and MMC.
[trini: This includes two clocks not listed in the Linux binding, which
needs resyncing later]
Previously, dynamic frequency scaling supported rates only through fixed
divison.
This virtual clock mux configuration enables more varied rates on A72
clock ID 202 by setting up the required register.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Signed-off-by: Reid Tonking <reidt@ti.com>
