This function will be needed by the upcoming Designware master SPI
driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
This patch includes the latest DT sources for socfpga from the current
Linux kernel. And enables CONFIG_OF_CONTROL for the new build target
"socfpga_socrates" (the EBV SoCrates board) to make use of this new DT
support.
Until this patch, the only SoCFPGA U-Boot target in mainline is
"socfpga_cyclone5". This build target is not (yet) changed to support
DT. So nothing changes for this target. Even though the long-term
goal should be to move all SoCFPGA targets over to DT.
One of the reasons to enable DT support in SoCFPGA is, that I need to
support multiple different SPI controllers for this platform. This is
the QSPI Cadence controller and the Designware SPI master controller.
Both are implemented in the SoCFPGA. And enabling both controllers is
only possible by using the new driver model (DM). The DM SPI code
only supports DT based probing. So it was easier to move SoCFPGA to
DT than to add the (deprecated) platform-data based probing to the
DM SPI suport.
Note that the image with the dtb embedded is u-boot-dtb.img. This needs
to be used now for those DT enabled boards instead of u-boot.img.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Cc: Simon Glass <sjg@chromium.org>
CompuLab cm-t3517 is Computer on Module (CoM) based on AM3517 SoC.
Features: up to 256MB DDR2, up to 512MB NAND, USB hub, mUSB, WiFi, BT,
Analog audio codec, touch screen controller, LED.
Add basic support including:
LED, Serial console, NAND, MMC, GPIO, I2C, 256MB DRAM.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Current get_board_rev() function returns a hard coded value which is
obviously incorrect for the majority of boards.
Allow boards to provide a correct implementation by making this
function weak.
In addition open code the trivial and useless BOARD_REV_ID define and
adjust the comment.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
The Keystone2 Lamar SoC uses the same keystone net driver.
This patch adds opportunity to use it by K2L SoCs.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Keystone2 Lamar SoC uses the same keystone SerDes driver.
All Keystone2 EVM boards currently use SerDes driver, so move
CONFIG_TI_KEYSTONE_SERDES to common configuration file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The Keystone2 Lamar SoC uses the same keystone navigator.
Move queue numbers to common hardware file, as all Keystone2 SoCs
have the same ones.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Add a driver for the designware serial UART used on sunxi. This just
redirects to the normal ns16550 driver.
Add a stdout-path to the device tree so that the correct UART is chosen.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
With driver model we will have access to a bank pointer, so we want to
use it rather than converting back to a number, and then back to a
bank pointer. Add functions to provide this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
For now we won't want to mess with the existing configurations. Create a
new one which will enable device tree and driver model. Note that this
brings the device tree binary into u-boot-sunxi-with-spl.bin.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
These are from Linux 3.17-rc7 (commit fe82dcec). U-Boot only uses a small
portion of these, but we may as well have something to look forward to.
The total compiled size is about 25KB.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Mostly automatic with:
sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I)
followed by removing the relevant #defines from include/configs/sun?i.h by
hand.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
And make TARGET_SUN[45678]I a choice variable under this.
configs updated with:
sed -i -e 's/^\(\+S:\)\?CONFIG_TARGET_SUN.I=y/\1CONFIG_ARCH_SUNXI=y\n&/g' configs/*
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
If CONFIG_RMOBILE_EXTRAM_BOOT is enabled, U-Boot is booted from External RAM.
The default boot address is 0x70000000.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
If CONFIG_RMOBILE_EXTRAM_BOOT is enabled, U-Boot is booted from External RAM.
The default boot address is 0x70000000.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
If CONFIG_RMOBILE_EXTRAM_BOOT is enabled, U-Boot is booted from External RAM.
The default boot address is 0xB0000000.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The change of the CPU frequency is waited for until PLL0ST of the PLLECR is
set to 1.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Initialization of L2CTLR[5] was set only as R8A7790 by commit
237faf095f.
However, initialization of cash needs to be performed continuously.
This changes into the processing which continues initialization of
L2CTLR[5] into L2CTLR cash and performs it.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
On mx6 sabreauto board, there are two USB ports:
0: OTG
1: HOST
The EHCI driver is enabled for this board, but the IOMUX and VBUS power
control is not implemented, which cause both USB port failed to work.
This patch fix the problem by adding the board support codes.
Since the power control uses the GPIO pin from port expander MAX7310,
the PCA953X driver is enabled for accessing the MAX7310.
The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting
its daisy chain. Add a new function "imx_iomux_set_gpr_register" to
handle GPR register setting.
Signed-off-by: Ye.Li <B37916@freescale.com>
For MX6SL and MX6SX, the perclk can come from OSC 24Mhz source. Fix
the get_ipg_per_clk function to support it.
Signed-off-by: Ye.Li <B37916@freescale.com>
Introduce a new configuration "CONFIG_MXC_GPT_HCLK". When it is set,
the GPT will select a high frequency clock as clock source.
Otherwise, the GPT will stay to use 32Khz OSC as clock source.
In the implementation, since only the GPT on i.MX6 series provide the
clock source option for 24Mhz OSC. For others (only i.MX5 and i.MX6
compile the driver), if the configuration is set, the perclk will be
selected as clock source.
MX6Q/D Rev 1.0 and MX6SL are special in the implementation, because they
don't have the 24Mhz OSC clock source option, so also select the perclk
for them. For MX6SL, we will set the OSC 24Mhz to perclk in CCM, so
eventually the clock comes from OSC 24Mhz.
Signed-off-by: Ye.Li <B37916@freescale.com>
Commit d58a9451e7 (ppc/arm: zap EMK boards) removed
TOP* boards support but missed to remove entries in Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
[1] arch/arm/include/asm/arch-at91/at91_shdwn.h
The top9000 was the last board to use this header file.
It was removed by commit d58a9451e7 (ppc/arm: zap EMK boards).
[2] board/matrix_vision/common/*
Some Matrix Vision boards were dropped by commit e7a565638a
(powerpc: mpc83xx: remove board support for MERGERBOX and MVBLM7)
and commit af55e35d33
(powerpc: mpc5xxx: remove board support for MVBC_P and MVSMR).
Since then these files have been unused.
[3] include/usb/omap1510_udc.h
The omap5912osk was the last board to use this header file.
It was removed by commit 62d636aa2a
(omap: remove omap5912osk board support).
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-By: Wolfgang Denk <wd@denx.de>
This patch adds extra gpio part addresses to exynos4
and exynos4x12_gpio_data arrays, which are required
since the gpio enum lists are linear
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
After remove the offsets in Exynos4/4x12 gpio enums,
an additional gpio base addresses are required.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add support for the Kosagi Novena board. Currently supported are:
- I2C busses
- FEC Ethernet
- MMC0, MMC1, Booting from MMC
- SATA
- USB ports
- USB Ethernet
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Nikolay Dimitrov <picmaster@mail.bg>
Reviewed-by: Nikolay Dimitrov <picmaster@mail.bg>
Add CONFIG_CMD_PINMON to UniPhier-specific Kconfig and make the
"pinmon" command user-configurable. This command can be disabled
via the configuration if users do not need it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Before this commit, the stack addresses for IRQ and FIQ modes,
IRQ_STACK_START and FIQ_STACK_START, were computed in interrupt_init but
they were not used.
This commit sets the stack pointers for IRQ and FIQ modes.
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This commit relocates the exception vectors.
As ARM1176 and ARMv7 have the security extensions, it uses VBAR. For
the other ARM processors, it copies the relocated exception vectors to
the correct address: 0x00000000 or 0xFFFF0000.
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Tom Warren <twarren@nvidia.com>
A regression was introduced in commit 41623c91. The consequence of that
is the non-relocation of the section .vectors symbols :
_undefined_instruction, _software_interrupt, _prefetch_abort,
_data_abort, _not_used, _irq and _fiq.
Before commit 41623c91, the exception vectors were in a .text section.
The .text section has the attributes allocatable and executable [1].
In commit 41623c91, a specific section is created, called .vectors, with
the attribute executable only.
What have changed between commit 41623c91^ and 41623c91 is the attribute
of the section which contains the exception vectors.
An allocatable section is "a section [that] occupies memory during
process execution" [1] which is the case of the section .vectors.
Adding the lacking attribute (SHF_ALLOC or "a") for the definition of
the section .vectors fixed the issue.
To summarize, the fix has to mark .vectors as allocatable because the
exception vectors reside in "memory during execution" and they need to
be relocated.
[1] http://man7.org/linux/man-pages/man5/elf.5.html
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This commit introduces a Kconfig symbol for each ARM CPU:
CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136,
CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100.
Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected
for CPU_ARM1176 and CPU_V7.
For each target, the corresponding CPU is selected and the definition of
SYS_CPU in the corresponding Kconfig file is removed.
Also, it removes redundant "string" type in some Kconfig files.
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
In preparation for the SoCFPGA support of the designware I2C driver,
convert this driver to the common CONFIG_SYS_I2C framework.
This patch converts all users of this driver, this is:
- ST spearxxx boards
- AXS101 (ARC700 platform)
I couldn't test this patch on those boards. Only compile tested for all
spear boards. And tested on SoCFPGA.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
The following bard configurations have been without active maintenance
for a long time, and the board maintainer agrees to have them removed:
MPC5200: TOP5200, MINI5200, EVAL5200
MPC860: TOP860
at91sam9xeXXX: top9000eval_xe, top9000su_xe
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
[trini: Add missing Kconfig removals]
Signed-off-by: Tom Rini <trini@ti.com>
There is no gaps in exynos gpio enum after rework, so the gpio
numbers should be adjusted to the new numbering.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is no gaps in exynos gpio enum after rework, so the gpio
numbers should be adjusted to the new numbering.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is no gaps in exynos gpio enum after rework, so the gpio
numbers should be adjusted to the new numbering.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is no gaps in exynos gpio enum after rework, so the gpio
numbers should be adjusted to the new numbering.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
The gpy0 don't need any additional register offset,
but the gpx0 does, so now it is fixed.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
The gpf0 offset was bad and it's now fixed.
After fix gpio order in *pinctrl.dts , the gpy0 offset is not required now.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
The pinctrl dts was imported from the kernel, but the order
of GPM and GPY is wrong. The gpio enum in: asm/arch/gpio.h
is proper.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
CONFIG_SPL should not be enabled for boards that do not have SPL.
CONFIG_SUPPORT_SPL introduced by this commit should be "select"ed
by boards with SPL support and CONFIG_SPL should depend on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Rename some defines containing FAT in their name to be filesystem generic:
MMCSD_MODE_FAT => MMCSD_MODE_FS
CONFIG_SPL_FAT_LOAD_ARGS_NAME => CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME => CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION => CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@ti.com>
Switch to the common spl.h file and zap the arch/spl.h . Since the arch/spl.h
contained various ad-hoc symbols, zap those symbols as well and rework the
board configuration a little so it doesn't depend on them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Pavel Machek <pavel@denx.de>
Move this initialization code to proper place. The misc_init_r()
function is called way too late and the platform initialization
code should be executed much earlier.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Pavel Machek <pavel@denx.de>
Because CONFIG_MMU is never defined in U-Boot,
the non-MMU code in debug.S is always used.
Unfortunately, the number of arguments of the addruart macro
in Linux is different between MMU and non-MMU.
This causes a build error when importing some debug macros
using the third argument. (For ex. arch/arm/include/debug/exynos.S)
Pass the third argument to the non-MMU addruart to avoid such a problem.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
We have not had a good method to debug the early boot stage such as
lowlevel_init function. I guess developers generally use dedicated
debuggers for that, but it is difficult in some cases.
(For example, my debugger cannot connect to the ARM processor when
it is in the secure state. It sometimes happens when I need to
debug the early boot stage on ARM SoCs with secure extension.)
The low level debug feature in Linux would be also helpful for U-boot
when we are stucking in nasty problems where the console is not
available yet.
You have to enable CONFIG_DEBUG_LL to use this feature.
For now, only 8250-compatible UART devices are supported.
You can add a header file under arch/arm/include/debug/ directory
to support your UART device if necessary.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
U-Boot does not have arch/arm/kernel, include/uapi directories,
This commit copies files as follows:
Location in Linux -> Location in U-Boot
arch/arm/kernel/debug.S -> arch/arm/lib/debug.S
arch/arm/include/debug/8250.S -> arch/arm/include/debug/8250.S
include/uapi/linux/serial_reg.h -> include/linux/serial_reg.h
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Add a Kconfig option which users can select when they want to boot older
kernels, e.g. the linux-sunxi 3.4 kernels. For now this just forces the pll5
"p" value to 1 (divide by 2) as that is what those kernels are hardcoded too,
in the future this may enable further workarounds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@ti.com>
--
Changes in v2:
-s/CONFIG_OLD_KERNEL_COMPAT/CONFIG_OLD_SUNXI_KERNEL_COMPAT.
-Move the code block setting P(1) for old kernels to where P gets cleared
This is a preparation patch for making the pll5 "p" divisor configurable
through Kconfig.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is a preparation patch for making the pll5 "p" divisor configurable
through Kconfig.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The A23 only has UART0 muxed with MMC0. Some of the boards we
encountered expose R_UART as a set of pads.
Add support for R_UART so we can have a console while using mmc.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The prcm apb0 controls multiple modules. Allow specifying which
modules to enable clocks and de-assert resets so the function
can be reused.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The A31, A23 and later SoCs have an extra pin controller, called CPUs_PIO
or R_PIO, which handles pin banks L and beyond.
Also add a clear description about SUNXI_GPIO_BANKS, stating it only
counts the number of pin banks in the _main_ pin controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: expanded commit message]
[wens@csie.org: add pin bank M and expand comments]
[wens@csie.org: add comment on SUNXI_GPIO_BANKS macro]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The basic blocks of the A23 are similar to the A31 (sun6i). Re-use
sun6i code for initial clock, gpio, and uart setup.
There is no SPL support for A23, as we do not have any documentation
or sample code for DRAM initialization.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Allwinner A23 SoC has reset controls like the A31 (sun6i).
The FIFO address is also the same as sun6i.
Re-use code added for sun6i.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Allwinner SoCs provide uart0 muxed with mmc0, which can then be used
with a micro SD breakout board. On the A23, this is the only way to
use uart0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The watchdog on sun6i/sun8i has a different layout.
Add the new layout and fix up the setup functions so that reset works.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
[ ijc -- removed sun5i workaround from sun6i/sun8i codepath as discussed ]
The RTC hardware has been moved out of the timer block on sun6i/sun8i.
In addition, there are more watchdogs available.
Also note that the timer block definition is not completely accurate
for sun5i/sun7i. Various blocks are missing or have been moved out.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On later Allwinner SoCs, the watchdog hardware is by all means a
separate hardware block, with its own address range and interrupt
line.
Move the register definitions to a separate file to facilitate
supporting newer SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
None of the known sunxi devices actually use mmc1 routed through PH, where
as some devices do actually use mmc1 routed through PG, so change the routing
of mmc1 to PG. If in the future we encounter devices with mmc1 routed through
PH, we will need to change things to be a bit more flexible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
sunxi SOCs can boot from both mmc0 and mmc2, detect from which one we're
booting, and make that one "mmc dev 0" so that a single u-boot binary can
be used for both the onboard eMMC and for external sdcards.
When we're booting from mmc2, we make it dev 0 because that is where the SPL
will load the tertiary payload (the actual u-boot binary in our case) from,
see: common/spl/spl_mmc.c, which has dev 0 hardcoded everywhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a new sun6i machine that supports UART and MMC.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: use SPDX labels, adapt to Kconfig system, drop ifdef
around mmc and smp code, drop MACH_TYPE]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: commit message was "ARM: sunxi: Setup the A31 UART0 muxing"]
[wens@csie.org: reorder #ifs by SUN?I]
[wens@csie.org: replace magic numbers with GPIO definitions]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The mmc hardware on sun6i has an extra reset control that needs to
be de-asserted prior to usage. Also the FIFO address is different.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: use setbits_le32 for reset control, drop obsolete changes,
rewrite different FIFO address handling, add commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch adds the basic clocks support for the Allwinner A31 (sun6i)
processor. This code will not been compiled until the build is hooked
up in a later patch. It has been split out to keep the patches manageable.
This includes changes from the following commits from u-boot-sunxi:
a92051b ARM: sunxi: Add sun6i clock controller structure
1f72c6f ARM: sun6i: Setup the UART0 clocks
5f2e712 ARM: sunxi: Enable pll6 by default on all models
2be2f2a ARM: sunxi-mmc: Add mmc support for sun6i / A31
12e1633 ARM: sun6i: Add initial clock setup for SPL
1a9c9c6 ARM: sunxi: Split clock code into common, sun4i and sun6i code
0b194ee ARM: sun6i: Properly setup the PLL LDO in clock_init_safe
b54c626 sunxi: avoid sr32 for APB1 clock setup.
68fe29c sunxi: remove magic numbers from clock_get_pll{5,6}
c89867d sunxi: clocks: clock_get_pll5 prototype and coding style
501ab1e ARM: sunxi: Fix sun6i PLL6 settings
37f669b ARM: sunxi: Fix macro names for mmc and uart reset offsets
61de1e6 ARM: sunxi: Correct comment for MBUS1 register in sun6i clock definitions
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: styling fixes reported by checkpatch.pl]
[wens@csie.org: drop unsupported SPL code block and unused gpio.h header]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The A31 has a new module called PRCM, or Power, Reset Control Module.
This module controls clocks and resets for RTC block modules, and also
PLL biasing in the main clock module.
This patch adds the register definitions, and also enables the clocks
and resets for the RTC block PIO (pin controller) and P2WI (push-pull
2 wire interface) which is used to talk to the PMIC.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: spacing fixes reported by checkpatch.pl]
[wens@csie.org: Use setbits helper in PRCM init function]
[wens@csie.org: rephrase commit message to explain what the hardware
supports and what we actually enable]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
A31 has several new and changed memory address. This patch adds them.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We have already defined macros for pull-up/down values in the
GPIO header. Use them instead of magic numbers when configuring
the UART pins.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This commit converts UniPhier on-chip serial driver to driver model.
Since UniPhier SoCs do not have Device Tree support, some board files
should be added under arch/arm/cpu/armv7/uniphier/ph1-*/ directories.
(Device Tree support for UniPhier platform is still under way.)
Now the base address and master clock frequency are passed from
platform data, so CONFIG_SYS_UNIPHIER_SERIAL_BASE* and
CONFIG_SYS_UNIPHIER_UART_CLK should be removed.
Tested on UniPhier PH1-LD4 ref board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
These ended up in arch/arm/dts/dt-bindings temporarily, but in fact the
correct place is now include/dt-bindings. Move them to be consistent.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the configuration for the am33xx boards, including beagleboard,
to use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
Provide suitable platform data for am33xx boards, so that these boards can
use driver model for serial.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Provide suitable platform data for am33xx boards, so that these boards can
use driver model for GPIO access.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Add driver model support to this driver, while retaining support for the
legacy system. Driver model GPIO support is enabled with CONFIG_DM_GPIO
as usual.
Since gpio_is_valid() no longer exists, we can use the -EINVAL error
returned from gpio_request().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
The private libgcc is supported only on ARM, MIPS, PowerPC, SH, x86.
Those architectures should "select" HAVE_PRIVATE_LIBGCC and
CONFIG_USE_PRIVATE_LIBGCC should depend on it.
Currently, this option is enabled on Tegra boards and x86 architecture.
Move the definition from header files to Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
The cm-t35 board support covers both cm-t3530 and cm-t3730 boards.
Mention both boards in the Kconfig option prompt.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Add ddr3 commands:
test <start_addr in hex> <end_addr in hex> - test DDR from start\n
address to end address\n
ddr compare <start_addr in hex> <end_addr in hex> <size in hex> -\n
compare DDR data of (size) bytes from start address to end
address\n
ddr ecc_err <addr in hex> <bit_err in hex> - generate bit errors\n
in DDR data at <addr>, the command will read a 32-bit data\n
from <addr>, and write (data ^ bit_err) back to <addr>\n
Delete CONFIG_MAX_UBOOT_MEM_SIZE, as it was supposed to be used
for ddr3 commands and for now it's not needed any more.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds the DDR3 ECC support to enable ECC in the DDR3
EMIF controller for Keystone II devices.
By default, ECC will only be enabled if RMW is supported in the
DDR EMIF controller. The entire DDR memory will be scrubbed to
zero using an EDMA channel after ECC is enabled and before
u-boot is re-located to DDR memory.
An ecc_test environment variable is added for ECC testing.
If ecc_test is set to 0, a detection of 2-bit error will reset
the device, if ecc_test is set to 1, 2-bit error detection
will not reset the device, user can still boot the kernel to
check the ECC error handling in kernel.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The EDMA3 controller’s primary purpose is to service data transfers
that you program between two memory-mapped slave endpoints on the device.
Typical usage includes, but is not limited to the following:
- Servicing software-driven paging transfers (e.g., transfers from external
memory, such as SDRAM to internal device memory, such as DSP L2 SRAM)
- Servicing event-driven peripherals, such as a serial port
- Performing sorting or sub-frame extraction of various data structures
- Offloading data transfers from the main device DSP(s)
- See the device-specific data manual for specific peripherals that are
accessible via the EDMA3 controller
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
For K2E and K2L SoCs clock output from PASS PLL has to be enabled
after NETCP domain and PA module are enabled. So create new function
for that and call it after PA module is enabled.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The Keystone2 Edison SoC uses the same keystone net driver.
This patch adds opportunity to use it by K2E SoCs.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Keystone2 Edison SoC uses the same keystone SerDes driver.
This patch adds support for K2E SoCs.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
As MDIO bus has been added we can register PHYs with it.
After registration, the PHY driver will be probed according to the
hardware on board.
Startup PHY at the ethernet open.
Use phy_startup() instead of keystone_get_link_status() when eth open,
as it verifies PHY link inside and SGMII link is checked before.
For K2HK evm PHY configuration at init was absent, so don't enable
phy config at init for k2hk evm.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
SerDes driver is used by other sub systems like PCI, sRIO etc.
So modify it to be more general. The SerDes driver provides common
API's that can also be extended for other peripherals SerDes
configurations.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Enhance the driver to use cmu/comlane/lane specific configurations
instead of 1 big array of configuration.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch split the Keystone II SGMII SerDes related code from
Ethernet driver and create a separate SGMII SerDes driver.
The SerDes driver can be used by others keystone subsystems
like PCI, sRIO, so move it to driver/soc/keystone directory.
Add soc specific drivers directory like in the Linux kernel.
It is going to be used by keysotone soc specific drivers.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
With MAC_PHY sgmii configuration, u-boot checks PHY link status before
sending each packet. Increasing MDIO frequency increases overall tftp
speed. We set it to maximum 2.5MHz.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The header file for the driver should be in correct place.
So move it to "arch/arm/include/asm/ti-common/keystone_net.h"
and correct driver's external dependencies. At the same time
align and correct some definitions.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Currently the network driver is used only by k2hk evm board.
The k2hk SoC contains NETCP v1.0, but Keystone2 SoCs, like k2e
contain NETCP v1.5. So driver should be able to work with such kind
of NETCP. This commit adds this opportunity. The main difference in
masks and some registers, the logic is the same, so only definitions
should be changed. To differentiate between versions add KS2_NETCP_V1_0
and KS2_NETCP_V1_5. Also remove unused and no more needed defines.
The port number is specific for each board so move this parameter to
configuration.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch removes K2HK SOC specifc emac_regs structure, it uses
soc specific register offset to keep the network driver common across
all the Keystone II EVMs.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patches enables the On-chip Shared Ram clock domain for K2L SoC.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The initialization of PLLs is a part of board specific code, so
move it appropriate places.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds Keystone II Lamar (K2L) SoC specific definitions
to support MSMC cache coherency.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds clock definitions and commands to support Keystone II
K2L SOC.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds hardware definitions specific to Keystone II
Lamar (K2L) SoC.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The usage description of commands refers to headers of sources,
that is not correct. This patch is intended to fix it.
Also generalize code in order to reduce SoC dependent #ifdefs.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Add support of usb xhci. xHCI controls all USB speeds of the Host
mode, that is, the SS through the SS PHY, as well as the HS, FS, and
LS through the USB2 PHY. xHCI replaces and supersedes all previous
host HCIs (HS-only EHCI, FS/LS OHCI and UHCI), and is therefore not
backwards compatible with any of them. The USB3SS’s USB Controller is
fully compliant with xHC.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The keystone_nav driver is general driver intended to be used for
working with queue manager and pktdma for different IPs like NETCP,
AIF, FFTC, etc. So the it's API shouldn't be named like it works only
with one of them, it should be general names. The names with prefix
like netcp_* rather do for drivers/net/keystone_net.c driver. So it's
good to generalize this driver to be used for different IP's and
delete confusion with real NETCP driver.
The current netcp_* functions of keystone navigator can be used for
other settings of pktdma, not only for NETCP. The API of this driver
is used by the keystone_net driver to work with NETCP, so net driver
also should be corrected. For convenience collect pkdma
configurations in drivers/dma/keystone_nav_cfg.c.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The keystone_nav is used by drivers/net/keystone_net.c driver to
send and receive packets, but currently it's placed at keystone
arch sources. So it should be in the drivers directory also.
It's separate driver that can be used for sending and receiving
pktdma packets by others drivers also.
This patch just move this driver to appropriate directory and
doesn't add any functional changes.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Use definitions in netcp_pktdma instead direct addresses.
The definitions can be set specifically for SoC, so there
is no reason to check SoC type while initialization.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Use definitions in qm_config. The definitions can be set specifically
for SoC, so there is no reason to check SoC type while initialization.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The maxBCM board is equipped with the Marvell Armada-XP MV78460 SoC. It
integrates an SPI NOR flash and an Marvell 88E6185 switch.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds basic support for the Marvell DB-MV784MP-GP evaulation
board. This is the first board that uses the recently created
Armada XP 78460 SoC support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
This basic support for the Marvell Armada XP is base on the existing kirkwood
support. Which has been generatized by moving some common files into
common marvell locations.
This is in preparation for the upcoming Armada XP MV78460 support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Additionally the SDRAM address decoding register address is not hard coded
in the C code any more. A define is introduced for this base address.
This makes is possible to use those gpio functions from other MVEBU SoC's
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This makes is possible to use this SPI driver from other MVEBU SoC's as well.
As the upcoming Armada XP support will do.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This makes is possible to use those gpio functions from other MVEBU SoC's as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
These mbus functions are ported from Barebox. The Barebox version is
ported from Linux. These functions will be first used by the upcoming
Armada XP support. Later other Marvell SoC's will be adopted to use
these functions as well (Kirkwood, Orion).
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
This patch does the following:
- Rename defines and registers to not use kirkwood
- Remove unused defines
- Use clrsetbits() accessor functions
- Coding style cleanup
- Clear 25MHZ bit in timer controller register init for Armada XP
There is no functional change for kirkwood. At least not intentionally.
This will be used by the upcoming Armada XP support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This move makes it possible to use this kirkwood SPI driver from other
MVEBU platforms as well. This will be used by the upcoming Armada XP
support.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
By moving some kirkwood files into a Marvell common directory, those files
can be used by other Marvell platforms as well. The name mvebu is taken
from the Linux kernel source tree. It has been chosen there to represent
the SoC's from the Marvell EBU (Engineering Business Unit). Those SoC's
currently are:
Armada 370/375/XP, Dove, mv78xx0, Kirkwood, Orion5x
This will be used by the upcoming Armada XP (MV78460) platform support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
The built-in SMSC 95xx chip doesn't know its own MAC address. Instead,
we must query it from the VC firmware; it's probably encoded in fuses
on the BCM2835.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Convert the BCM2835 GPIO driver to use driver model, and switch over
Raspberry Pi to use this, since it is the only board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
GPIOs should be requested before use. Without this, driver model will
not permit the GPIO to be used.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
This converts the Tegra SPI drivers to use driver model. This is tested
on:
- Tegra20 - trimslice
- Tegra30 - beaver
- Tegra124 - dalmore
(not tested on Tegra124)
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
All boards with a SPI interface have a suitable spi alias except the tegra30
boards. Add these missing aliases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Adjust this board to use the driver model soft_spi implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Move the exynos SPI driver over to driver model. This removes quite a bit
of boilerplate from the driver, although it adds some for driver model.
A few device tree additions are needed to make the SPI flash available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Convert the exynos GPIO driver to driver model. This implements the generic
GPIO interface but not the extra Exynos-specific functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model GPIOs must be requested before use. Make sure this is
done correctly.
(Note that the soft SPI part of universal is omitted, since this driver
is about to be replaced with a driver-model-aware version)
Signed-off-by: Simon Glass <sjg@chromium.org>
The wrong header is being included, thus requiring the code to re-declare
the generic GPIO interface in each GPIO header.
Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The pinctrl bindings used by Linux are an incomplete description of the
hardware. It is possible in most cases to determine the register address
of each, but not in all cases. By adding an additional property we can
fix this, and avoid adding a table to U-Boot for every single Exynos
SOC.
Signed-off-by: Simon Glass <sjg@chromium.org>
We don't include the pinctrl functions for U-Boot as they use up quite
a bit of space and are not used.
We could instead perhaps eliminate this material with fdtgrep, but so far
this tool has not made it to upstream.
Signed-off-by: Simon Glass <sjg@chromium.org>
Bring in required device tree files for pinctrl from Linux v3.14. These
are initially unchanged and have a number of pieces not needed by U-Boot.
Note that exynos5420 is renamed to exynos54xx here since we want to
support exynos5422 also.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should be consistent about this. The kernel has moved to #include
which breaks error reporting to some extent but does allow us to include
binding files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update Apalis T30 as per the following commits
c369139234
tegra: dts: Add serial port details
461be2f96e
kconfig: remove redundant "string" type in arch and board Kconfigs
f1ef2b6233
kconfig: move CONFIG_DEFAULT_DEVICE_TREE to kconfig
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add missing chosen stdout-path device tree node. This got missed by
commit
c369139234
tegra: dts: Add serial port details
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On popular request this now completes the Warren's work started for
TK1:
aeb3fcb359
ARM: tegra: Use mem size from MC rather than ODMDATA
In addition to the move of using the Tegra memory controller (MC)
register rather than ODMDATA for T20, T30 and T114 as well it further
uses the generic get_ram_size() function (see "common/memsize.c")
<supposed to be used in each and every U-Boot port>TM. Added benefit is
that it should <catch 99% of hardware related (i. e. reliably
reproducible) memory errors> as well.
Thoroughly tested on the various Toradex line of Tegra modules
available which unfortunately does not include T114 and T124 (yet at
least) plus on the Jetson TK1.
Based-on-work-by: Stephen Warren <swarren@nvidia.com>
Based-on-work-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds board support for the Toradex Apalis T30 a computer on
module which can be used on different carrier boards.
For the sake of ease of use we do not distinguish between different
carrier boards for now as the base module features are deemed
sufficient enough for regular booting.
The following functionality is working so far:
- eMMC boot and environment storage
- Gigabit Ethernet (once Thierry's PCIe as well as my E1000 resp. i210
fixes hit mainline)
- MMC/SD cards (both 8-bit as well as 4-bit slot)
- USB client/host (dual role port as client e.g. for DFU/UMS, other two
ports as host)
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Declare displays[] and display_count in imx-common/video.h to
prevent "Should it be static?" messages when compiling board
files with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Provide a public declaration of the board_spi_cs_gpio()
callback for i.MX SPI chip selects to prevent the warning
"Should it be static?" when compiling with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Include <asm/bootm.h> to see the prototype for get_board_rev()
and prevent warning "Should it be static?" with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Without preceding declarations, "make C=1" generates
"Should it be static?" warnings for symbols
do_bootm_linux,
boot_prep_vxworks, and
boot_jump_vxworks
Include of bootm.h also identified a signature mismatch
(const on argv[]).
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Hardware accelerated support for SHA-1 and SHA-256 has been added.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On OMAP platforms, SATA controller provides the SCSI subsystem
so implement scsi_init().
Get rid of the unnecessary sata_init() call from dra7xx-evm
and omap5-uevm board files.
Signed-off-by: Roger Quadros <rogerq@ti.com>
rmobile/lowlevel_init_ca15.S are common in r8a7790, r8a7791 and r8a7794 of
rmobile SoCs. The initialize L2 cache in lowlevel_init_ca15.S only needed
for Cortex-A15. The r8a7794 is Cortex-A7, not Cortex-A15.
This adds Skip to initialize L2 cache when r8a7794.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
rmobile/lowlevel_init_ca15.S are common in r8a7790 and r8a7791 of
rmobile SoC. But L2 cache of r8a7791 does not use L2CTLR[5].
This adds fix to set L2CTLR [5] only when the r8a7790.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Move cache handling code to C file, and add enable_caches() and
disable_caches() functions.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Change this board to add a device tree.
This also adds a pinmux header file although it is not used as yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Most of the smdkv310 features are common with other exynos4 boards. To
permit easier addition of driver model support, use the common file and
add a device tree file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add a keyboard definition so that the keyboard can be used on pit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The device seems to hang in SPL if the full speed is used when booting from
USB, perhaps because the PMIC has not been set to the maximum ARM core
voltage yet. Slow it down to a reliable speed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Removed settings in unsupported register fields. They didn’t
do anything, and in most cases, were not documented in the
reference manual.
Changed register settings to comply with JEDEC required values.
Changed timing parameters because they included full clock
periods that were doing nothing.
Signed-off-by: Anthony Felice <tony.felice@timesys.com>
[rebased on v2014.10-rc2]
Signed-off-by: Stefan Agner <stefan@agner.ch>
Add command to enable and disable the bridges between HPS and FPGA.
This patch does have a checkpatch issue with the assembler portion,
checkpatch correctly complains that there should be no whitespace
before quoted newline. I do not agree that fixing this specific
checkpatch issue will improve the readability, thus this one is not
addressed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
Move icache_enable() and dcache_enable() function calls from
board code into the CPU code and into the enable_caches()
function. This is how the cache enabling code was designed
to work.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Add code which configures the AMBA NIC-301 and the SCU on the SoCFPGA .
The code sets the access permissions for the CPU to the AMBA slaves such
that the CPU can access them in both secure and non-secure mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Configure the PL310 address filter to make sure DRAM is mapped to 0x0.
This code also configures the "remap" register of NIC-301 and sets the
required 'mpuzero' bit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Add register definition for the NIC-301 used on SoCFPGA.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Add the Snoop Control Unit register definition file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Add missing system manager bits from Altera U-Boot to make the code
comparable. These are the bits which depend on the FPGA manager.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Add function to enable and disable FPGA bridges. This code is used
by the FPGA manager to disable the bridges before programming the
FPGA and will later be also used by the initialization code for the
chip to put the chip into well defined state during startup.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Add code necessary to program the FPGA part of SoCFPGA from U-Boot
with an RBF blob. This patch also integrates the code into the
FPGA driver framework in U-Boot so it can be used via the 'fpga'
command.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
V2: Move the not-CPU specific stuff into drivers/fpga/ and base
this on the cleaned up altera FPGA support.
Cosmetic change to the print_cpuinfo() function output. Align the
output with the rest of initial output produced by U-Boot.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Add CPU function to register and initialize the dw_mmc SD controller.
This allows us to use the HPS SDMMC block.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Add function to initialize the EMAC blocks upon board startup.
The preprocessor guards against building on SoCFPGA-VT and against
SPL build are not needed as those are handled implicitly via both
SPL framework and the socfpga_cyclone5.h config file, which will
not define CONFIG_DESIGNWARE_ETH if building for SoCFPGA-VT.
We cannot handle two EMAC ethernet blocks yet, therefore the ifdefs.
Once there is hardware using both EMAC blocks, this ifdef will have
to go.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Add functions to reset the EMAC ethernet blocks. We cannot handle
two EMAC ethernet blocks yet, therefore the ifdefs. Once there is
hardware using both EMAC blocks, this ifdef will have to go.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
The timer reload value is a property of the timer hardware and there
is no reason for this to be configurable. Place this into the timer
driver just like on the other hardware.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Add the missing pieces from the reference clock code from Altera. This
puts the code on par with the Altera U-Boot fork for all but the SDRAM
self-refresh bits, which are not part of this patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Clean up the clock code definitions so they are aligned with mainline
standards. There are no functional changes in this patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Pull out functions to read frequency of Main clock VCO and
PLL clock VCO as the code is duplicated multiple times.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Add the entire bulk of code to read out clock configuration from the SoCFPGA
CPU registers. This is important for MMC, QSPI and UART drivers as otherwise
they cannot determine the frequency of their upstream clock.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
V2: Fixed the L4 MP clock divider and synced the clock code with latest
rocketboards codebase (thanks Dinh for pointing this out)
The inlining is done by GCC when needed, there is no need to do it
explicitly. Furthermore, the inline keyword does not force-inline
the code, but is only a hint for the compiler. Scrub this hint.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
The bit definitions for clock manager are complete chaos. Implement
some basic logical order into them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Clean up the system manager register definition and add the missing
register definitions in place.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
This adds watchdog disable. It is neccessary for running Linux kernel.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
V2: Move RSTMGR_PERMODRST_L4WD0_LSB to reset_manager.h
Reset watchdog only if CONFIG_HW_WATCHDOG is undefined (the default)
Sort the list of functional block addresses and fix indentation.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
Add base addresses for all subsystems as documented in the
Cyclone V HPS documentation.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
Add configuration for the write-allocate mode of L1 D-Cache on ARM.
This is needed for D-Cache operation on Cortex-A9 on the SoCFPGA .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
This patch adds support for the OT1200 series of devices.
Following components are used in u-boot:
+ ethernet
+ i2c
+ emmc
+ gpio
For more details see README.
Changes v1 > v2
- make use of enable_cspi_clock(..)
- fix usage of OUTPUT_40OHM define
- added README
Changes v2 > v3
- improve spelling in README
- added own copy of mx6q_4x_mt41j128.cfg
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
i.MX6SX ROM implements unified table sections.
The HAB function table is at offset 0x100. Update
the HAB function pointers accordingly.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
The mx6sl/mx6sx has 2 OTG and 1 host. So they have name
"USBO2H_USB_BASE_ADDR" in imx-regs.h. The driver hard codes
the USB base address name to "USBOH3", which causes the driver
failed to build for mx6sl/mx6sx.
This patch uniform the address name to "USB_BASE_ADDR" for all
mx6 series.
Signed-off-by: Ye.Li <B37916@freescale.com>
Checking the pre_periph_clk_sel and pre_periph2_clk of CCM CBCMR
register, if the PLL2 PFD0 or PLL2 PFD2 is used for the clock source,
do not reset this PFD to avoid system hang. Customers may set this
in DDR script or use BT_FREQ to select low freq boot.
Signed-off-by: Ye.Li <B37916@freescale.com>
Instead of waiting for a fixed period of time and hoping for the best
that the DRAM will start, read back an EMI status register which tells
us exactly when the DRAM started.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
According to i.MX23 datasheet Table 32-17, we must wait for the supply
to settle before disabling the current limiter. Indeed, not waiting a
little here causes the system to crash at times.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
LS1021AQDS has a variant with DDR4 slot. This patch adds a new defconfig
for this variant to enable DDR4 support. RAW timing parameters are not
added for DDR4. The board timing parameters are only tuned for single-
rank 1600 and 1800MT/s with Micron DIMM 9ASF51272AZ-2G1A1 due to DIMM
availability.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
Secondary cores need to be released from holdoff by boot release
registers. With GPP bootrom, they can boot from main memory
directly. Individual spin table is used for each core. Spin table
and the boot page is reserved in device tree so OS won't overwrite.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
DP-DDR is used for DPAA, separated from main memory pool for general
use. It has 32-bit bus width and use a standard DDR4 DIMM (64-bit).
Signed-off-by: York Sun <yorksun@freescale.com>
This commit moves:
CONFIG_OF_CONTROL
CONFIG_OF_SEPARATE
CONFIG_OF_EMBED
CONFIG_OF_HOSTFILE
Because these options are currently not supported for SPL,
the "Device Tree Control" menu does not appear in the SPL
configuration.
Note:
zynq-common.h should be adjusted so as not to change the
default value of CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
When CONFIG_SECURE_BOOT is enabled, the signed images
like kernel and dtb can be authenticated using iMX6 CAAM.
The added command hab_auth_img can be used for HAB
authentication of images. The command takes the image
DDR location, IVT (Image Vector Table) offset inside
image as parameters. Detailed info about signing images
can be found in Freescale AppNote AN4581.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Using CPU_HAS_PCR micro to present the SoC has pcr
(peripheral control register).
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
When use pcr (peripheral control register), then we won't need
to care about the peripheral ID.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch implements a workaround to fix DDR3 memory issue.
The code for workaround detects PGSR0 errors and then preps for
and executes a software-controlled hard reset.In board_early_init,
where logic has been added to identify whether or not the previous
reset was a PORz. PLL initialization is skipped in the case of a
software-controlled hard reset.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Keegan Garcia <kgarcia@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
At the high level, the problem is that we set gd multiple times (and
still do, even after the commit we're reverting). We set important
parts of gd to the copy which is not above stack but rather in the data
section. For the release, we're going to revert this change and for the
next release we shall correct things to only, really, set gd once to an
appropriate location and ensure that comments about it are correct too.
This reverts commit f0c3a6c4ad.
Acked-by: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@ti.com>
We do not have to distinguish CONFIG_TARGET_VEXPRESS_AEMV8A_SEMI
from CONFIG_TARGET_VEXPRESS_AEMV8A. Rename the former to the latter.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Cc: David Feng <fenghua@phytium.com.cn>
This patch moves mx35 to the common timer functions added in commit
8dfafdd - Introduce common timer functions <Rob Herring>
The (removed) mx35 timer code (specifically __udelay()) could deadlock at
the 32-bit boundary of get_ticks(). get_ticks() returned a 32-bit value
cast up to a 64-bit value. If get_ticks() + tmo in __udelay() crossed
the 32-bit boundary, the while condition became unconditionally true and
locks the processor. Rather than patch the specific mx35 issues, simply
move everything over to the common code.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This patch moves mx31 to the common timer functions added in commit
8dfafdd - Introduce common timer functions <Rob Herring>
The (removed) mx31 timer code (specifically __udelay()) could deadlock at
the 32-bit boundary of get_ticks(). get_ticks() returned a 32-bit value
cast up to a 64-bit value. If get_ticks() + tmo in __udelay() crossed
the 32-bit boundary, the while condition became unconditionally true and
locks the processor. Rather than patch the specific mx31 issues, simply
move everything over to the common code.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Helmut Raiger <helmut.raiger@hale.at>
