With Club 3D dual link adapter there are AUX-channel timeouts
when EDID is read. Increasing retry interval time to max (400us)
fixes this.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Heiko Schocher <hs@denx.de>
On the BeagleBone these i2c1 pins are routed to the expanasion header, where
they can be defined as either pr1_usart0_Xxd/pwm0/spi0/i2c1, dont assume i2c1
Fixes: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/313894/1387696
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com>
CC: Tom Rini <trini@konsulko.com>
Since we don't have for sure a valid IP-setup during
board_late_init(...) because it maybe allready stored in environment or
not, we cannot form a proper vxWorks bootline at this place.
So we move to the way, forming the bootline just before
executing/launching vxWorks. To do this we use the bootvx command
instead go.
We only have to form the "othbootargs" environment variable, the rest is
done pretty good by the "bootvx" commannd.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Support LCDIF for mx7dsabresd board:
1. Add pinmux settings
2. Add VIDEO related macro definition and videomode env settings.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Support lcdif display:
1. Add pinmux and pad settings for LCDIF
2. Introduce setup_lcd to do the settings for LCDIF
3. Enable VIDEO related macros in board header files
4. Add a new env videomode which is needed by mxsfb.c. The
settings for videomode in this patch is for TFT43AB.
5. Tested on mx6ul 14x14/9x9 evk.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
board_mxsfb_system_setup must be renamed mxsfb_system_setup.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
There is really no need to provide an empty reset_cpu() implementation,
so just remove it.
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
There is really no need to provide an empty reset_cpu() implementation,
so just remove it.
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
There is really no need to provide an empty reset_cpu() implementation,
so just remove it.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
There is really no need to provide an empty reset_cpu() implementation,
so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Enable the GPU node in the system-wide ft_system_setup() hook instead of
the board-specific ft_board_hook(). This allows us to enable GPU per SoC
generation instead of per-board as we did initially.
Reported-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
p2371-2180 has two PCI ports; a regular x4 slot and a x1 M.2 slot. This
patch adds the relevant DT to enable the PCI controller and configure
the XUSB padctl pin muxing, and code to turn on the PCI power and enable
PCI features in U-Boot. I have only tested the x4 slot.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
ls1043ardb_nand_defconfig and ls1043ardb_sdcard_defconfig are missing
in the MAINTAINERS file, so add them for completeness.
Reported-by: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
A few config files have been added without updating MAINTAINERS.
Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
In 522b021 we dropped 'PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4)' lines in
the mpc85xx linker scripts as this is not required and breaks newer
binutils. This commit cleans up the rest of the powerpc linker scripts.
Signed-off-by: Tom Rini <trini@konsulko.com>
A few config files have been added without updating MAINTAINERS.
Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Revert commit 7a2c1b13 which dropped OpenRD boards.
Assume maintainership of OpenRD.
Remove OpenRD from scrapyard.
Switch OpenRD to generic board.
Switch to Thumb build.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This board runs a P5020 or P5040 chip, and utilizes
an EEPROM with similar formatting to the Freescale P5020DS.
Large amounts of this code were developed by
Adrian Cox <adrian at humboldt dot co dot uk>
Signed-off-by: Andy Fleming <afleming@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Remove zc70x target which was one setting for zc702 and zc706.
Currently zc702 and zc706 are separated.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
When detecting SDHC Adapter Card Type 2(SD/MMC Legacy Adapter Card),
enable EVDD automatic control via SDHC_VS. This could support SD card
IO voltage switching for UHS-1 speed mode.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
If adapter card type identification is supported for platform, we would
enable dat[4:7] for eMMC4.5 Adapter Card.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
qe-tdm is muxed with diu, if hwconfig setted as qe-tdm,
assign muxed pins to qe-tdm, then delete diu node from
device tree.
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch will fix these checkpatch issues.
CHECK: Alignment should match open parenthesis
+ printf("Enter: %s %s\n", mode_name[mode][0],
+ mode_info[mode]);
CHECK: Alignment should match open parenthesis
+ lcd_printf("\n\n\t%s %s\n", mode_name[mode][0],
+ mode_info[mode]);
CHECK: Alignment should match open parenthesis
+ lcd_printf("\t%s %s - %s\n\n", selection[i],
+ mode_name[i][0],
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch will fix these checkpatch issues.
+static const char *mmc_regulators[] = {
CHECK: Blank lines aren't necessary before a close brace '}'
+
+}
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch will fix these checkpatch issues.
ERROR: spaces required around that '==' (ctx:VxV)
+#if FCLK_SPEED==0 /* Fout = 203MHz, Fin = 12MHz for Audio */
ERROR: spaces required around that '==' (ctx:VxV)
+#elif FCLK_SPEED==1 /* Fout = 202.8MHz */
ERROR: spaces required around that '==' (ctx:VxV)
+#if USB_CLOCK==0
ERROR: spaces required around that '==' (ctx:VxV)
+#elif USB_CLOCK==1
CHECK: spaces required around that ':' (ctx:VxV)
+ "bne 1b":"=r" (loops):"0" (loops));
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit adds additional file with implementation of board
detection code for Odroid-XU3/XU4.
The detection depends on compatible found in fdt:
- "samsung,exynos5" - uses Exynos5 generic code
- "samsung,odroidxu3" - try detect XU3 revision
There are few revisions of Odroid XU3/XU4, each can be detected
by checking the value of channel 9 of built-in ADC:
Rev ADC Board
0.1 0 XU3 0.1
0.2 372 XU3 0.2 | XU3L - no DISPLAYPORT
0.3 1280 XU4 0.1
The detection code depends on the ADC+10% value.
Implementation of functions:
- set_board_type() - read ADC and set type
- get_board_rev() - returns board revision: 1..3
- get_board_type() - returns board type string
Additional functions with return values of bool:
- board_is_generic() - true if found compatible "samsung,exynos5"
but not "samsung,odroidxu3"
- board_is_odroidxu3() - true if found compatible "samsung,odroidxu3"
and one of XU3 revision.
- board_is_odroidxu4() - true if found compatible "samsung,odroidxu3"
and XU4 revision.
After I2C controller init, the get_board_type() can check
if the XU3 board is a "Lite" variant, by probing chip
0x40 on I2C0 (INA231 - exists only on non-lite).
This is useful for setting fdt file name at misc_init_r().
Enabled configs:
- CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
- CONFIG_ODROID_REV_AIN
- CONFIG_REVISION_TAG
- CONFIG_BOARD_TYPES
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The function get_board_type() is called in two places by common code,
but the returned pointer was never check.
This commit adds checking the returned pointer, before use it.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
It will take more than 1s when wake up from deep sleep. Most of the
time is spent on outputing information. This patch reduced the deep
sleep latency by:
1. avoid outputing system informaton
2. remove flush cache after DDR restore
3. skip reloading second stage uboot binary when SD boot
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The ITS bit was being read incorrectly beacause of operator
precedence. The same ahs been corrected.
Signed-off-by: Lawish Deshmukh <lawish.deshmukh@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add i.MX6DQP-Sabresd board support:
1. set fdt_file according to board_rev which is set at runtime.
2. Add mx6dqp_ddr_ioregs and calibration value for this board.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
setting the gpr 1,8 and 12 registers to a fix value.
This is needed because after a WDT reset, this registers
are not correct resettet, and prevent linux from booting
again.
Signed-off-by: Heiko Schocher <hs@denx.de>
Freescale ARM-based Layerscape LS102xA contain a SATA controller
which comply with the serial ATA 3.0 specification and the
AHCI 1.3 specification.
This patch adds SATA feature on ls1021aqds and ls1021atwr boards.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds esdhc support for ls1043ardb.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1043ARDB Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 SDRAM (32bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* XFI 10G port
* QSGMII with 4x 1G ports
* Two RGMII ports
PCIe:
* PCIe2 (Lanes C) to mini-PCIe slot
* PCIe3 (Lanes D) to PCIe slot
USB 3.0: two super speed USB 3.0 type A ports
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
There are two LS series processors are built on ARMv8 Layersacpe
architecture currently, LS2085A and LS1043A. They are based on
ARMv8 core although use different chassis, so create fsl-layerscape
to refactor the common code for the LS series processors which also
paves the way for adding LS1043A platform.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The fsl_dtsec.h & fsl_tgec.h & fsl_fman.h can be shared on both ARM
and PPC, move it out of ppc to include/, and change the path in
drivers accordingly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Config Security Level Register is different between different SoCs,
so put the CSL register definition into the arch specific directory.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For the Chain of Trust, the esbc_validate command supports
32 bit fields for location of the image. In the header structure
definition, these were declared as pointers which made them
64 bit on a 64 bit core.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This board has not compiled for me for quite some time due to size
constraints, remove.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board has not compiled for me for quite some time due to size
constraints, remove.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board has not compiled for me for quite some time due to size
constraints, remove.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board has not compiled for me for quite some time due to size
constraints, remove.
Cc: John Otken <jotken@softadvances.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported in
SD boot now. For the customer's demand, QSPI needs to be supported in SD
boot too.
This patch adds QSPI or IFC support in SD boot according to the
corresponding defconfig. For detail, ls1021atwr_sdcard_ifc_defconfig is
used to support IFC in SD boot and ls1021atwr_sdcard_qspi_defconfig is
used to support QSPI in SD boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In the "Getting Started with Coccinelle - KVM edition" presentation that
has been held by Julia Lawall at the KVM forum 2015 (see the slides at
http://events.linuxfoundation.org/sites/events/files/slides/tutorial_kvm_0.pdf),
she pointed out some bad return value checks in U-Boot that can be
detected with Coccinelle by using the following config file:
@@
identifier x,y;
identifier f;
statement S;
@@
x = f(...);
(
if (x < 0) S
|
if (
- y
+ x
< 0) S
)
This patch now fixes these issues.
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Add CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG support and enable it to set
'board_rev' and 'board_name' envs.
'board_rev' can be used in scripts to determine what board we are running on
and 'board_name' for pretty printing.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Convert altera sysid to driver model with misc uclass.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert altera_pio to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As altera_pio_init() uses BSS, it should be moved to
board_early_init_r().
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Marek Vasut <marex@denx.de>
Currently omap_hsmmc driver doesn't use sdcd pin to detect
whether the card is present or not. Instead the same pin is used
as GPIO to detect card presence. So change the pin mux mode from
mmc0_sdcd to gpio0_6.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add MMC support for k2g
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Add Ethernet support for tftp support
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Phy mode is a board property and it can be different between
multiple board and ports, so it should not be hardcoded in
driver to one specific mode. So adding a field in eth_priv_t
structure to pass phy mode to driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add clock information for Galileo
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Prepare board file so that ethernet registration are
commented for DM conversion
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since there is a common function to grab the serial number from the die id bits,
it makes sense have one to parse that serial number and feed it to the serial
ATAG.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces omap_die_id_display to display the full die id.
There is no need to store it in an environment variable, that no boot script
is using anyway.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that we have a common prototype to grab the omap die id, functions to figure
out a serial number and usb ethernet address can use it directly.
Those also get an omap_die_id prefix for better consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces omap5 support for omap_die_id, which matches the common
omap_die_id definition. It replaces board-specific code to grab the die id bits.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces omap4 support for omap_die_id, which matches the common
omap_die_id definition. It replaces board-specific code to grab the die id bits.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This replaces the previous get_dieid definition with omap_die_id, that matches
the common omap_die_id definition.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
board_name environment variable was not getting set correctly for Pandaboard A4 and ES
Signed-off-by: David Batzle <dbatzle@dcbcyber.com>
CC: Albert Aribaud <albert.u.boot@aribaud.net>; Tom Rini <trini@ti.com>; Peter Robinson <pbrobinson@gmail.com>
The C.H.I.P. is a small SBC with an Allwinner R8, 8GB of NAND, 512MB of
RAM, USB host and OTG, a wifi / bluetooth combo chip, an audio/video jack
and two connectors to plug additional boards on top of it.
The DT is identical to the DT submitted to the upstream kernel.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Not all sunxi boards have an MMC embedded. Switching to the Kconfig option
will allow to enable or disable the support in each boards' defconfig.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Sinovoip BPI-M2 is a SBC board based on the A31s SoC it features
1G RAM, a microsd slot, Gbit ethernet, 4 usb-a USB-2 ports, ir receiver,
stereo headphone jack and hdmi video output.
The dts changes are identical to the dts files submitted upstream.
A few notes on the use if dldo and aldo regulators. DLDO1 is used
for Vdd for the ethernet phy, ALDO2 is used for AVdd for the ethernet
phy. ALDO1 is used to power the sdio wifi module.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Stop prefixing the axp functions for setting voltages, etc. with the
model number, there ever is only one pmic driver built into u-boot,
this allows simplifying the callers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On boards with axp221/223 pmic-s we already allow configuring most
voltages. Make the Kconfig options for these also apply to boards with
axp152 / axp209 pmic-s and extend them to configure all voltages.
The Kconfig defaults are chosen so that this commit does not introduce any
functional changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We now have generic q8_a?3_defconfig files for Q8 formfactor tablets with
an A13 / A23 / A33 SoC, there is no need for these PCB variant specific
defconfig-s and they only serve to confuse the user.
Note that in case of the forfun_q88db_defconfig and TZX-Q8-713B7_defconfig
for A13 based Q8 tablets there is not even a dts file for these in the
upstream kernel, which is all the more reason to remove them.
The generic q8_a?3_defconfig files have been tested on an Et_q8_v1_6,
Ippo_q8h_v1_2_a33_1024x600, Ippo_q8h_v1_2 and TZX-Q8-713B7 tablet, and the
forfun_q88db_defconfig is identical to q8_a13_tablet_defconfig.
This leaves only the Ippo_q8h_v5 untested with the new generic defconfigs
but there is no reason to assume that it will not work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Select CONFIG_SPL_STACK_R for sunxi boards, this gives us much more
room on the stack once we've the DRAM running.
Besides being a good change to have on itself, this also paves the
way for switching to using malloc_simple in the SPL which cuts of
close to 4KiB of the SPL size.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
