Commit graph

6145 commits

Author SHA1 Message Date
Mugunthan V N
b1e26e3bfb ARM: DRA7xx: Add CPSW support to DRA7xx EVM
Adding support for CPSW Ethernet support found in DRA7xx EVM

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Mugunthan V N
2bf36ac638 drivers: net: cpsw: remove hard coding bd ram for cpsw
BD ram address may vary in various SOC, so removing the hardcoding and
passing the same information through platform data

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Tom Rini
5d4dbf1c3a am335x_evm: Add basic README
Add a README for the family of boards the am335x_evm covers, and include
instructions on preparing and using falcon mode, for various media.

Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2013-07-26 16:39:11 -04:00
Christian Riesch
3864cb2133 da850evm: Use clrbits function with correct endianess
The current code uses clrbits_be32 which is incorrect since we are on
a little endian machine here. This patch fixes this issue and also removes
some unnecessary code: Reading the current GPIO bank state is not required
if we are using the SET and CLEAR GPIO registers for setting/clearing
bits.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Cc: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
2013-07-26 16:39:10 -04:00
Tom Rini
9fab4bf4cc powerpc/ppc4xx: Convert new gdsys files to SPDX license tags
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-26 15:32:59 -04:00
Fabio Estevam
f8b1e86d47 mx6qsabrelite: Remove mx6qsabrelite code in favor of nitrogen6x
mx6qsabrelite and nitrogen6q boards are hardware compatible, so let's avoid the
code duplication and only use the nitrogen6x source code to make board code
maintainance easier.

Tested booting a mainline device tree kernel on a mx6qsabrelite board.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-07-26 16:44:29 +02:00
Dirk Eibach
0f0c1021d8 powerpc/ppc4xx: Consider gdsys FPGA OSD size
OSD size was constant 32x16 characters.
Now the size is set as announced by the FPGA.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
2013-07-25 19:35:42 +02:00
Dirk Eibach
e50e8968d9 powerpc/ppc4xx: Support gdsys multichannel iocon hardware
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
2013-07-25 19:35:42 +02:00
Dirk Eibach
049de79d85 powerpc/ppc4xx: Add gdsys mclink interface
mclink is a serial interface for communication between gdsys FPGA.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
2013-07-25 19:35:42 +02:00
Dirk Eibach
aba27acf67 powerpc/ppc4xx: Use generic accessor functions for gdsys FPGA
A set of accessor functions was added to be able to access not only
memory mapped FPGA in a generic way.

Thanks to Wolfgang Denk for getting this sorted properly.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
2013-07-25 19:35:42 +02:00
Albert ARIBAUD
8b485ba12b Merge branch 'u-boot/master' into u-boot-arm/master 2013-07-25 17:57:46 +02:00
Tom Rini
aaf5e82560 Merge branch 'master' of git://git.denx.de/u-boot-nds32 2013-07-25 08:51:51 -04:00
Tom Rini
0b17998e50 qemu-malta: Update for SPDX license identifiers
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-25 08:51:48 -04:00
Tom Rini
230187ce26 Merge branch 'master' of git://git.denx.de/u-boot-mips
Conflict over SPDX changes means that one change was effectively dropped
as it was fixing typos in a removed hunk of text.

Conflicts:
	arch/mips/cpu/mips64/start.S

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-25 08:51:48 -04:00
Dinh Nguyen
12607adcd5 socfpga: Move board/socfpga_cyclone5 to board/socfpga
Because the SOCFPGA platform will include support for Cyclone V and
Arria V FPGA parts, renaming socfpga_cyclone5 folder to socfpga to
be more generic.

Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Tom Rini <trini@ti.com>

v2:
- Add Reviewed-by: Pavel Machek
- Cc: Tom Rini
2013-07-25 10:54:52 +02:00
ken kuo
951344b778 nds32: Convert Makefiles to use COBJS-y style
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
2013-07-25 16:54:18 +08:00
Rob Herring
953950234d ARM: highbank: compile misc_init_r only if CONFIG_MISC_INIT_R
Compile misc_init_r only if CONFIG_MISC_INIT_R is enabled.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-07-25 08:16:21 +02:00
Rob Herring
76c3999db4 ARM: highbank: setup peripherals based on power domain status
Accessing powered down peripherals will hang the bus, so check power
domain status before initializing SATA and fixup the FDT to disable
unused peripherals.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-07-25 08:16:07 +02:00
Gabor Juhos
f1957499ea MIPS: qemu-malta: bring up ethernet
Qemu emulates a PCNET PCI card for the Malta CoreLV board.
Enable the pcnet driver and add board specific ethernet
initialization function to bring it up. Also enable the
CONFIG_CMD_NET and CONFIG_CMD_PING options.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:04 -04:00
Gabor Juhos
feaa606627 MIPS: qemu-malta: add PCI support
Qemu emulates the Galileo GT64120 System Controller
which provides a CPU bus to PCI bus bridge.

The patch adds driver for this bridge and enables
PCI support for the emulated Malta board.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:04 -04:00
Gabor Juhos
ac12984de8 MIPS: qemu-malta: setup GT64120 registers as done by YAMON
Move the GT64120 register base to 0x1be00000
and setup PCI BAR registers as done by the
original YAMON bootloader.

This is needed for running Linux kernel.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:04 -04:00
Gabor Juhos
015643152a MIPS: qemu-malta: add reset support
The MIPS Malta board has a SOFTRES register. Writing a
magic value into that register initiates a board reset.

Use this feature to implement reset support.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:03 -04:00
Gabor Juhos
5a4dcfac1e MIPS: qemu-malta: add support for emulated MIPS Malta board
Add minimal support for the MIPS Malta CoreLV board
emulated by Qemu. The only supported peripherial is
the UART.

This is enough to boot U-Boot to the command prompt
both in little and big endian mode.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:03 -04:00
Tom Rini
c2120fbfbc Merge branch 'master' of git://git.denx.de/u-boot-i2c
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
	board/sandburst/common/ppc440gx_i2c.c
	board/sandburst/common/ppc440gx_i2c.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:50:24 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
ken kuo
3c016704d9 nds32: Enable two banks of SDRAM on Andes board
The original adp-ag101/adp-ag101p initialize only one bank(64MB)
by default at boot time, but it is not enough for some application,
so increasing to two banks(128M).

Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
2013-07-24 11:50:28 +08:00
Gabor Juhos
f6fd4140a5 nds32: adp-ag102: use 'faraday/ftpci100.h' for pci_ftpci_init
Due to improper external function declaration,
building U-Boot for the adp-ag102 board shows
this warning:

  adp-ag102.c: In function 'pci_init_board':
  adp-ag102.c:95: warning: function declaration isn't a prototype

Include the 'faraday/ftpci100.h' header which
provides the proper declaration and remove the
local declaration to get rid of the warning.

Compile tested only.

Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
2013-07-24 11:49:17 +08:00
Alison Wang
1221b3d74a vf610: Add I2C support for Vybrid VF610 platform
This patch adds I2C support for Vybrid VF610 platform and adds
I2C0 support to VF610TWR board.

Signed-off-by: Alison Wang <b18965@freescale.com>
2013-07-23 08:34:57 +02:00
Dirk Eibach
880540decf i2c, ppc4xx_i2c: switch to new multibus/multiadapter support
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
2013-07-23 08:34:56 +02:00
Simon Glass
1f2ba722ac tegra: i2c: Enable new CONFIG_SYS_I2C framework
This enables CONFIG_SYS_I2C on Tegra, updating existing boards and the Tegra
i2c driver to support this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
2013-07-23 08:34:55 +02:00
Heiko Schocher
f3e9361771 i2c, multibus, keymile: get rid of EEprom_ivm envvariable
as the keymile boards use now the new i2c multibus/multiadapter
framework, remove the EEprom_ivm Environmentvar, as not longer
needed.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Holger Brunck <holger.brunck@keymile.com>
Tested-By: Holger Brunck <holger.brunck@keymile.com>
2013-07-23 08:34:54 +02:00
Heiko Schocher
00f792e0df i2c, fsl_i2c: switch to new multibus/multiadapter support
- added to fsl_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-07-23 08:34:53 +02:00
Heiko Schocher
ea818dbbcd i2c, soft-i2c: switch to new multibus/multiadapter support
- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-07-23 05:54:29 +02:00
Bo Shen
b899fa3901 arm: at91sam9n12: change EBI IO to high drive mode
As both the DDR SDRAM and NAND flash connect to EBI on at91sam9n12
and share the lower 8 bits data line. If use low drive of the data
line, it will cause DDR data access corrupt in lower address, so
change the data line to high drive mode

This will fix the Linux kernel boot issue when use Lower address

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-07-22 08:20:14 -04:00
Troy Kisky
fdf86c202c ddr cfg: DRAM_RESET needs 0x00020030
The old value of 0x000e0030 will cause ethernet
timeout issues on the sabrelite and possibly other
boards using the KSZ9021.
I have no explanation as to why.

But this is a correct change, the TRM will be updated
to show that 00b is the only valid setting for bits
19-18 of DRAM_RESET.

My thanks go to Liu Hui(Jason) for this information.

Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-07-20 12:14:09 -04:00
Dirk Eibach
b9944a77f9 mpc85xx: Add gdsys ControlCenter Digital board
The gdsys ControlCenter Digital board is based on a Freescale P1022 QorIQ SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2x GbE
- Lattice ECP3 FPGA connected via PCIe
- mSATA RAID1
- USB host
- DisplayPort video output
- Atmel TPM

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-07-16 17:44:30 -05:00
Łukasz Majewski
baa8841d6c arm:samsung:trats:fix: Restore proper orientation of TRATS's LCD panel
Before setting: mipi_lcd_device.reverse_panel = 1, the Trats's LCD panel
was flipped by 180 degrees.

The flip was caused by following change:
Exynos: Change get_timer() to work correctly
SHA1: 3d00c0cb96

This commit fixed udelay(), which is necessary (due to HW LCD controller
oddity) for mipi-dsi correct operation. As a result the display orientation
has been switched.

As a follow up, the hwrevision() function has been removed, since it was
used only in this particular place.

Test HW: Trats Exynos4210 rev 0.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2013-07-16 09:20:16 -04:00
Wolfgang Denk
f4ea9f86d1 PPC MPC83xx: Fix MPC8323ERDB build warning
Fix:

mpc8323erdb.c: In function 'mac_read_from_eeprom':
mpc8323erdb.c:198:3: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]

Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Timur Tabi <timur@tabi.org>
cc: Kim Phillips <kim.phillips@freescale.com>
2013-07-15 18:03:15 -04:00
Tom Rini
54e458de55 Revert "MIPS: Jz4740: Add qi_lb60 board support"
The files board/qi/qi_lb60/qi_lb60.c and include/configs/qi_lb60.h were
licensed under the GPL v3 or later, and not v2 or later.  As this is
incompatible with the project, revert this board support until the
responsible parties are available to re-license (if so desired) under
GPL v2.

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-15 09:19:39 -04:00
Tom Rini
fbbbc86e8e Merge branch 'master' of git://git.denx.de/u-boot-arm
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.

Conflicts:
	arch/arm/dts/exynos5250.dtsi

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-12 10:36:48 -04:00
Stephen Warren
d035fcf9b6 ARM: tegra: enable LCD panel on Ventana
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-07-11 14:15:16 -07:00
Stephen Warren
b46694df84 ARM: tegra: enable LCD panel on Harmony
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-07-11 14:15:16 -07:00
Jim Lin
7e44d9320e ARM: Tegra: USB: EHCI: Add support for Tegra30/Tegra114
Tegra30 and Tegra114 are compatible except PLL parameters.

Tested on Tegra30 Cardhu, and Tegra114 Dalmore
platforms. All works well.

Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-07-11 14:15:15 -07:00
Jim Lin
56867d88c4 ARM: Tegra: FDT: Add USB EHCI function for T30/T114
Add DT node for USB EHCI function.
Add support for T30-Cardhu, T30-Beaver, T114-Dalmore boards.

Signed-off-by: Jim Lin <jilin@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-07-11 14:15:15 -07:00
Albert ARIBAUD
630aacb085 Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2013-07-10 20:40:47 +02:00
Amar
1ae76d438b EXYNOS: Resolve the i2c compilation error
This patch resolves the below mentioned compilation error of i2c driver
for non-FDT case

Compilation error:
s3c24x0_i2c.c: In function 'board_i2c_init':
s3c24x0_i2c.c:544:18: error: 'CONFIG_MAX_I2C_NUM' undeclared (first use
in this function) s3c24x0_i2c.c:544:18: note: each undeclared
identifier is reported only once for each function it appears in
s3c24x0_i2c.c:545:3: warning: implicit declaration of function

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-07-10 14:20:26 +09:00
Rajeshwari Shinde
643be9c07e EXYNOS: Move files from board/samsung to arch/arm
This patch performs the following:

1) Convert the assembly code for memory and clock initialization to C code.
2) Move the memory and clock init codes from board/samsung to arch/arm
3) Creat a common lowlevel_init file across Exynos4 and Exynos5. Converted
   the common lowlevel_init from assembly to C-code
4) Made spl_boot.c and tzpc_init.c common for both exynos4 and exynos5.
5) Enable CONFIG_SKIP_LOWLEVEL_INIT as stack pointer initialisation is already
   done in _main.
6) exynos-uboot-spl.lds made common across SMDKV310, Origen and SMDK5250.

TEST: Tested SD-MMC boot on SMDK5250 and Origen.
      Tested USB and SPI boot on SMDK5250
      Compile tested for SMDKV310.

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-07-05 17:06:55 +09:00
Rajeshwari Shinde
198a40b9f6 EXYNOS4210: Configure GPIO for uart
This patch configures the gpio values for UART
on Origen and SMDKV310 using pinmux

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-07-05 17:06:55 +09:00
Rajeshwari Shinde
6e50e5ca02 EXYNOS: LDS file move to common
smdk5250-uboot-spl.lds is moved to common folder, so that it can be reused.
It is renamed to exynos-uboot-spl.lds

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-07-05 17:06:54 +09:00
Robert Winkler
327598945b omap: cm_t35: Fix cm_t35 for weak splash_screen_prepare
Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-07-01 21:47:40 +02:00
Albert ARIBAUD
e6c7f86f03 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-06-28 17:51:13 +02:00
Rajeshwari Shinde
493c073ff4 SMDK5250: Remove reduntant code
enum boot_mode is defined twice once in spl.h and also in
spl_boot.c, hence removing the same from spl_boot.c and including
the header file.

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-28 09:19:38 +09:00
Tom Rini
58a5c43c09 Merge branch 'master' of git://git.denx.de/u-boot-74xx-7xx 2013-06-27 08:23:27 -04:00
Wolfgang Denk
b8bfde7f01 PPC 74xx_7xx: Fix build warnings for ELPPC board
Fix:

misc.c: In function 'misc_init_r':
misc.c:210:3: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
misc.c:211:3: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
misc.c:212:3: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]

Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-06-27 08:12:28 +02:00
Fabio Estevam
5307188889 m28evk: Move README file inside board directory
Board specific READMEs should be located inside the respective board directory.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-06-26 17:41:06 +02:00
Fabio Estevam
17f3f36652 mx28evk: Move README file inside board directory
Board specific READMEs should be located inside the respective board directory.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-06-26 17:40:39 +02:00
Pierre Aubert
c174797061 imx: Add support for the SabreSD shipped with i.MX6DL
The SabreSD platform is available with i.MX6Q or i.MX6DL. This patch adds the
support of the i.MX6DL. The config file and the board directory are renamed
to remove the reference to the MX6Q.

Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-06-26 17:34:11 +02:00
Hung-ying Tyan
eb28fdac79 cros: exynos: enable cros-ec for smdk5250
This patch initiates cros-ec in board_init() to enable it for smdk5250.

This patch depends on the patch in the MMC series that brings in exynos5-dt.c.
Refer to http://patchwork.ozlabs.org/patch/240084.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
2013-06-26 10:15:52 -04:00
Hung-ying Tyan
60744a1187 cros: exynos: add cros-ec device nodes to exynos5250-snow.dts
This patch adds cros-ec related device nodes to exynos5250-snow.dts.
It also adds a gpio node to exynos5250.dtsi.

Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
2013-06-26 10:14:34 -04:00
Tapani Utriainen
491f2947a1 Add support for Wandboard Quad
Add support for the Quad version of Wandboard; fix compile warning resulting
from having 2G of memory.

Signed-off-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-06-26 16:14:32 +02:00
Tom Rini
ca85eb8c42 Merge branch 'master' of git://git.denx.de/u-boot-net 2013-06-24 22:27:44 -04:00
Bo Shen
162762205f ARM: at91sam9n12: add network support with ksz8851_16mll
add network support with ksz8851_16mll on at91sam9n12ek board

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-06-24 19:11:14 -05:00
Tom Rini
4e78e0317d Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx 2013-06-24 16:44:15 -04:00
Gerhard Sittig
14d4c5f39e ac14xx: re-order the recovery condition checks
re-order the conditions which make the recovery system startup: combine
those conditions which were explicitly initiated (key press, software
request) and those which post-process error conditions (installer issues)

Signed-off-by: Gerhard Sittig <gsi@denx.de>
2013-06-24 22:26:57 +02:00
Gerhard Sittig
527a1c71fb ac14xx: minor improvement in diagnostics
- minor rewording of diagnostics output
- make diagnostics optional and off by default

Signed-off-by: Gerhard Sittig <gsi@denx.de>
2013-06-24 22:26:30 +02:00
Gerhard Sittig
b5992e77ef ac14xx: cleanup comments in the board support
fix typos, minor rephrasing, remove obsolete notes and TODO items

Signed-off-by: Gerhard Sittig <gsi@denx.de>
2013-06-24 22:25:57 +02:00
Gerhard Sittig
186f9c130f ac14xx: fix a potential NULL deref in diagnostics
getenv() immediately after setenv() may perfectly legally return NULL, so
make sure to not deference an invalid pointer when creating diagnostic output

Signed-off-by: Gerhard Sittig <gsi@denx.de>
2013-06-24 22:24:29 +02:00
Rajeshwari Shinde
4603e8cf8b EXYNOS5: FDT: Add serial device node values
This patch adds the device node required for serial driver

Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-24 20:47:41 +09:00
Bernie Thompson
2955d60015 exynos: Adjust the starting MIF voltage to 1.05v
Some Exynos5250 silicon may require 1.05v on the MIF to be stable, so to be
safe we can default to 1.05v instead of 1.00v. This can be set optimally later
in the boot process by the kernel.

The 0x6 value for 1.05v comes from the MAX77686 datasheet.

Signed-off-by: Bernie Thompson <bhthompson@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-24 14:00:11 +09:00
Mike Dunn
0dc0e846f3 pxa: add support for palmtreo680 board
This patch adds support for the Palm Treo 680 smartphone.  A quick overview of
u-boot implementation on the treo 680...

The treo 680 has a Diskonchip G4 nand flash chip.  This device has a 2k region
that maps to the system bus at the reset vector in a NOR-like fashion so that it
can be used as the boot device.  The phone is shipped with this 2k region
configured as write-protected (can't be modified) and programmed with an initial
program loader (IPL).  At power-up, this IPL loads the contents of two flash
blocks to SDRAM and jumps to it.  The capacity of the two blocks is not large
enough to hold all of u-boot, so a u-boot SPL is used.  To conserve flash space,
these two blocks and the necessary number of subsequent blocks are programmed
with a concatenated spl + u-boot image.  That way, the IPL will also load a
portion of u-boot proper, and when the spl runs, it relocates the portion of
u-boot that the IPL has already loaded, and then resumes loading the remaining
part of u-boot before jumping to it.

The default_environment is used (CONFIG_ENV_IS_NOWHERE) because I didn't think
that having a writable environment was worth the cost of a flash block, although
adding it would be straightforward.  I abuse the CONFIG_EXTRA_ENV_SETTINGS
option to specify the usbtty for the console (CONFIG_SYS_CONSOLE_IS_IN_ENV).

Support for the LCD is included, but currently it is only useful for displaying
the u-boot splash screen.  But if u-boot is built without the usbtty console, it
does display the auto-boot progress nicely.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
2013-06-22 15:25:28 +02:00
Tom Rini
348e47f766 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-06-22 07:38:12 -04:00
Albert ARIBAUD
47bd65ef05 arm: make __rel_dyn_{start, end} compiler-generated
This change is only done where needed: some linker
scripts may contain relocation symbols yet remain
unchanged.

__rel_dyn_start and __rel_dyn_end each requires
its own output section; putting them in relocation
sections changes their flags and breaks relocation.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21 23:05:29 +02:00
Albert ARIBAUD
d026dec875 arm: make __image_copy_{start, end} compiler-generated
This change is only done where needed: some linker
scripts may contain __image_copy_{start,end} yet
remain unchanged.

Also, __image_copy_end needs its own section; putting
it in relocation sections changes their flags and makes
relocation break.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21 23:05:05 +02:00
Albert ARIBAUD
09d81184e1 remove all references to .dynsym
Discard all .dynsym sections from linker scripts
Remove all __dynsym_start definitions from linker scripts
Remove all __dynsym_start references from the codebase

Note: this touches include/asm-generic/sections.h, which
is not ARM-specific, but actual uses of __dynsym_start
are only in ARM, so this patch can safely go through
the ARM repository.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21 23:04:05 +02:00
Simon Glass
b2f794125e exynos: Enable mmc for snow
Snow has an internal eMMC and an external SD card. Enable these in the
device tree.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-21 09:08:46 +09:00
Chunhe Lan
5707233880 powerpc/85xx: Add P1023RDB board support
P1023RDB Specification:
-----------------------
Memory subsystem:
   512MB DDR3 (Fixed DDR on board)
   64MB NOR flash
   128MB NAND flash

Ethernet:
   eTSEC1: Connected to Atheros AR8035 GETH PHY
   eTSEC2: Connected to Atheros AR8035 GETH PHY

PCIe:
   Three mini-PCIe slots

USB:
   Two USB2.0 Type A ports

I2C:
   AT24C08 8K Board EEPROM (8 bit address)

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 17:08:53 -05:00
York Sun
5bdeff3214 powerpc/pixis: Fix pixis help message
"pixis_reset help" command prints the message without a new line "\n",
which makes the prompt on the same line.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 17:08:52 -05:00
Prabhakar Kushwaha
505c293ffd board/p1010rdb: Fix PCIe TLB creation on CONFIG_PCI define
PCIe TLB should be created with CONFIG_PCI defined

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 17:08:50 -05:00
Liu Gang
69fdf90010 powerpc/t4qds: Slave module for boot from SRIO and PCIE
When a T4 board boots from SRIO or PCIE, it needs to finish these processes:
	1. Set all the cores in holdoff status.
	2. Set the boot location to one PCIE or SRIO interface by RCW.
	3. Set a specific TLB entry for the boot process.
	4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
	5. Set a specific TLB entry in order to fetch ucode and ENV from
	   master.
	6. Set a LAW entry with the TargetID one of the PCIE ports for
	   ucode and ENV.
	7. Slave's u-boot image should be generated specifically by
	   make xxxx_SRIO_PCIE_BOOT_config.
	   This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.

For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 17:08:49 -05:00
Liu Gang
5870fe44b2 powerpc/b4860qds: Slave module for boot from SRIO and PCIE
When a b4860qds board boots from SRIO or PCIE, it needs to finish these
processes:
	1. Set all the cores in holdoff status.
	2. Set the boot location to one PCIE or SRIO interface by RCW.
	3. Set a specific TLB entry for the boot process.
	4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
	5. Set a specific TLB entry in order to fetch ucode and ENV from
	   master.
	6. Set a LAW entry with the TargetID one of the PCIE ports for
	   ucode and ENV.
	7. Slave's u-boot image should be generated specifically by
	   make xxxx_SRIO_PCIE_BOOT_config.
	   This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.

For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 17:08:48 -05:00
Prabhakar Kushwaha
f64bd7c038 powerpc/mpc85xx:Fix "boot page TLB" entry size for NAND SPL
e500v2 processor does not support 8K page size TLB entries.

So create new TLB entry only during NAND SPL boot.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 17:08:47 -05:00
Andy Fleming
8bd00c9494 85xx: Change case of MPC85XX_PORBMSR_ROMLOC_SHIFT
All the other constants use lowercase 'x' in "MPC85xx", so we
duplicate that here.

Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 16:09:09 -05:00
Priyanka Jain
1d2949aeb3 board/bsc9131rdb: Update default boot environment settings
BSC9131RDB has 1GB DDR.
Out of this, only 880MB is passed on to Linux via bootm_size.
Remaining
-16MB is reserved for PowerPC-DSP shared control area
-128MB is reserved for DSP private area.

Also 256MB, out of this 880MB is required for data communication between
PowerPC and DSP core.
For this bootargs are modified to pass parameter to create 1 hugetlb
page of 256MB via default_hugepagesz, hugepagesz and hugepages

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 16:09:08 -05:00
Priyanka Jain
765b0bdb89 board/bsc9131rdb: Add DSP side tlb and laws
BSC9131RDB is a Freescale Reference Design Board for
BSC9131 SoC which is a integrated device that contains
one powerpc e500v2 core and one DSP starcore.

To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 memory

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 16:09:08 -05:00
Priyanka Jain
087cf44fcd board/bsc9131rdb: Add targets for Sysclk 100MHz
BSC9131RDB supports Sysclk
-66MHz if jumper J16 is close (default state)
-100MHz if jumper J16 is open

Add targets
-BSC9131RDB_NAND_SYSCLK100 : for NAND boot at Sysclk 100MHz
-BSC9131RDB_SPIFLASH_SYSCLK100: for SPI boot at Sysclk 100MHz

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 16:09:08 -05:00
Prabhakar Kushwaha
83e0c2bbe3 board/bsc9132qds:Add NAND boot support using new SPL format
- Add NAND boot target
   - defines constants
   - Add spl_minimal.c to initialise DDR
   - update TLB, LAW entries as per NAND boot

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 16:09:08 -05:00
Prabhakar Kushwaha
f159326926 board/bsc9131rdb:Add NAND boot support using new SPL format
- Add NAND boot target
   - defines constants
   - Add spl_minimal.c to initialise DDR
   - update TLB entries as per NAND boot

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 16:09:07 -05:00
Prabhakar Kushwaha
0fa934d235 board/p1010rdb:Add NAND boot support using new SPL format
- defines constants
  - Add spl_minimal.c to initialise DDR
  - update TLB entries as per NAND boot
  - remove nand_spl support for P1010RDB

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 16:09:07 -05:00
Prabhakar Kushwaha
3a88179d03 powerpc/mpc85xx: new SPL support for IFC NAND
Linker script is not able find start.o binary. So add its absolute path in
u-boot-spl.lds. This change is similar to u-boot-nand.lds

common/Makefile: Avoid compiling unnecssary files

fsl_ifc_spl.c : It is is responsible for reading u-boot binary from
NAND flash and copying into DDR. It also transfer control from NAND SPL
to u-boot image present in DDR.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 16:08:58 -05:00
Simon Guinot
7737c99460 net2big_v2: initialize LEDs at startup
This patch allows to configure the net2big_v2 LEDs at startup (through
the GPIO extension bus). The front blue LED is enabled and the SATA rear
LEDs are configured to blink in relation with the SATA activity.

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
2013-06-20 14:01:23 +05:30
Simon Guinot
d5cc3f5241 LaCie/common: add support for the CPLD GPIO bus
This patch adds support for the CPLD GPIO bus found on some LaCie boards
(as the 2Big/5Big Network v2 and the 2Big NAS). This parallel GPIO bus
exposes two registers (address and data). Each of this register is made
up of several dedicated GPIOs. An extra GPIO is used to notify the CPLD
that the registers have been updated.

Mostly this bus is used to configure the LEDs on LaCie boards.

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
2013-06-20 14:01:23 +05:30
Simon Guinot
2af4d0f49f net2big_v2: initialize I2C fan at startup
This patch ensures minimal cooling for the net2big_v2 by automatically
starting the I2C fan (GMT G762) at low speed (2800 RPM).

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2013-06-20 14:01:23 +05:30
Albert ARIBAUD
c2543a21df Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-06-19 23:58:01 +02:00
Albert ARIBAUD
69f14dc2fd Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'
Conflicts:
	spl/Makefile
2013-06-19 12:53:59 +02:00
Dan Murphy
bf3b98a188 arm: omap4: panda: Fix checkpatch on panda file
Fix the checkpatch warning on the panda.c file for leading
spaces.
Fix the CHECK warnings on the panda.c file for parenthesis alignment.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-06-18 10:43:30 -04:00
Dan Murphy
7d47d1caa0 arm: omap4: panda: Add reading of the board revision
Detect if we are running on a panda revision A1-A6,
or an ES panda board. This can be done by reading
the level of GPIOs and checking the processor revisions.
This should result in:
Panda 4430:
     GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5
     GPIO171, GPIO101, GPIO182: 1 0 1 => A6
Panda ES:
     GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
     GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3

Set the board name appropriately for the board revision that
is detected.

Update the findfdt macro to load the a4 device tree binary.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
[trini: %s/CONTROL_PADCONF_CORE/(*ctrl)->control_padconf_core_base/ and
 formatting for that]
Signed-off-by: Tom Rini <trini@ti.com>
2013-06-18 10:43:30 -04:00
Heiko Schocher
7ea7f689ca arm, am33xx: move uart soft reset code to common place
move uart soft reset code to common place and call
this function from board code, instead of copy and paste
this code for every board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
[trini: Fix igep0033 build, remove 'regval' on pcm051]
Signed-off-by: Tom Rini <trini@ti.com>
2013-06-18 10:40:06 -04:00
Heiko Schocher
49f7836500 arm, am33xx: move rtc32k_enable() to common place
move rtc32k_enable() to common place so all am33xx boards can use it.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-06-18 09:12:38 -04:00
Tom Rini
41341221d1 Merge branch 'master' of git://git.denx.de/u-boot-arm
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR

Conflicts:
	arch/arm/include/asm/arch-omap5/omap.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-13 15:16:15 -04:00
Amar
c748be0d30 SMDK5250: Enable EMMC booting
This patch adds support for EMMC booting on SMDK5250.

Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13 17:35:14 +09:00
Amar
752f4c4a9c SMDK5250: Initialise and Enable DWMMC, support FDT and non-FDT
This patch enables and initialises DWMMC for SMDK5250.
Supports both FDT and non-FDT. This patch creates a new file
'exynos5-dt.c' meant for FDT support.
        exynos5-dt.c:   This file shall contain all code which supports FDT.
                        Any addition of FDT support for any module needs to be
                        added in this file.
        smdk5250.c:     This file shall contain the code which supports non-FDT.
                        version. Any addition of non-FDT support for any module
                        needs to be added in this file.
                        May be, the file smdk5250.c can be removed in near future
                        when non-FDT is not required.

The Makefile is updated to compile only one of the files
exynos5-dt.c / smdk5250.c based on FDT configuration.

NOTE:
Please note that all additions corresponding to FDT need to be added into the
file exynos5-dt.c.
At same time if non-FDT support is required then add the corresponding
updations into smdk5250.c.

Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13 17:35:14 +09:00
Amar
07eb5f9ce7 EXYNOS5: FDT: Add DWMMC device node data
This patch adds DWMMC device node data for exynos5.
This patch also adds binding file for DWMMC device node.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13 17:35:13 +09:00
Sergey Yanovich
c3442c1e32 arm: pxa: Add support for ICP DAS LP-8x4x
LP-8x4x is a programmable automation controller by ICP DAS. It is
shipped with outdated U-Boot v1.3.0

This patch adds enough supports to boot the board:
 - 128M of 128M SDRAM
 - 32M of 48M NOR Flash memory
 - 1 of 4 Serial consoles (PXA FFUART)
 - 2 of 2 Ethernet controllers (DM9000)

Signed-off-by: Sergey Yanovich <ynvich@gmail.com>
Series-to: u-boot
Series-cc: marex
2013-06-12 22:24:09 +02:00
Albert ARIBAUD
1b83470f3c Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-06-10 18:28:37 +02:00
Holger Brunck
74ae612fd8 arm/km: make local functions static
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-06-10 17:25:41 +02:00
Vishwanathrao Badarkhe, Manish
68cd4a4c9f arm: da830: moved pinmux configurations to the arch tree
Move pinmux configurations for the DA830 SoCs from board file
to the arch tree so that it can be used for all da830 based devices.
Also, avoids duplicate pinmuxing in case of NAND.

Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
2013-06-10 08:54:46 -04:00
Tom Rini
7f5eef93af arm: Remove OMAP2420H4 and all omap24xx support
The omap2420H4 was the only mainline omap24xx board.  Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time.  Remove this board as there's not been interest in
it in U-Boot for quite a long time.

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-10 08:43:19 -04:00
Vishwanathrao Badarkhe, Manish
03e08d7cf6 da830: add MMC support
Add MMC support for da830 boards in order to perform
mmc operations(read,write and erase).

Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
2013-06-10 08:43:11 -04:00
Lokesh Vutla
7f36c88f64 ARM: DRA7xx: Update pinmux data
Updating pinmux data as specified in the latest DM

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
af1d002f89 ARM: OMAP2+: Rename asm/arch/clocks.h asm/arch/clock.h
To be consistent with other ARM platforms,
renaming asm/arch-omap*/clocks.h to asm/arch-omap*/clock.h

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Lokesh Vutla
9239f5b625 ARM: OMAP4+: Cleanup header files
After having the u-boot clean up series, there are
many definitions that are unused in header files.
Removing all those unused ones.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Joel A Fernandes
a662e0c345 am33xx: Board: Make CPSW section of ethernet initialization depend on CPSW driver
Not doing so breaks cases where CPSW is not required such as for USB RNDIS network boot.

Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
2013-06-10 08:43:08 -04:00
Albert ARIBAUD
10e167329b Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Conflicts:
	drivers/serial/Makefile
2013-06-08 14:35:10 +02:00
Peter Korsgaard
12d7a47420 am335x: enable falcon boot mode for mmc (raw and fat) and nand
Jump into full u-boot mode if a 'c' character is received on the uart.

We need to adjust the spl bss/malloc area to not overlap with the
loadaddr of the kernel (sdram + 32k), so move it past u-boot instead.

For raw mmc, we store the kernel parameter area in the free space after
the MBR (if used). For nand, we use the last sector of the partition
reserved for u-boot.

This also enables the spl command in the full u-boot so the kernel
parameter area snapshot can be created.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2013-06-07 14:17:01 -04:00
Tom Rini
47b8e52744 Merge branch 'master' of git://git.denx.de/u-boot-video 2013-06-07 08:35:36 -04:00
Fabio Estevam
4a1c7b13ae vf610twr: Drop unneeded 'status' variable
No need to use the 'status' variable, so just remove it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2013-06-06 17:52:08 +02:00
Stephen Warren
ea697ae7eb ARM: bcm2835: add simplefb DT node during bootz/m
Add a DT simple-framebuffer node to DT when booting the Linux kernel.
This will allow the kernel to inherit the framebuffer configuration from
U-Boot, and display a graphical boot console, and even run a full SW-
rendered X server.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Simon Glass <sjg@chromium.org>
2013-06-05 22:40:38 +02:00
Tom Rini
eecf9e2e78 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-06-05 12:45:34 -04:00
Tom Rini
4596dcc1d4 am33xx/omap: Move save_omap_boot_params to omap-common/boot-common.c
We need to call the save_omap_boot_params function on am33xx/ti81xx and
other newer TI SoCs, so move the function to boot-common.  Only OMAP4+
has the omap_hw_init_context function so add ifdefs to not call it on
am33xx/ti81xx.  Call save_omap_boot_params from s_init on am33xx/ti81xx
boards.

Reviewed-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-06-05 08:46:49 -04:00
SARTRE Leo
9b75bad0b9 Add support for Congatec Conga-QEVAl board
Add minimal support (only boot from mmc device) for the Congatec
Conga-QEVAl Evaluation Carrier Board with conga-Qmx6q (i.MX6 Quad
processor) module.

Signed-off-by: Leo Sartre <lsartre@adeneo-embedded.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2013-06-04 12:08:46 +02:00
Inderpal Singh
8a00061e20 exynos: Update origen and smdkv310 to use common tzpc_init
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-04 15:23:21 +09:00
Inderpal Singh
b5f9756f7f exynos: update tzpc to make it common for exynos4 and exynos5
This requires that cpu_is_exynos4/5 should be made available before tzpc_init.
Hence this patch also makes necessary changes to have cpu_info in spl and
invokes arch_cpu_init before tzpc_init in low_level_init.S for smdk5250.

Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-04 15:23:17 +09:00
Inderpal Singh
72af2fc850 exynos: move tzpc_init to armv7/exynos
tzpc_init is common for all exynos5 boards, hence move it to
armv7/exynos so that all other boards can use it.

Also update the smdk5250 Makefile and config file.

Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-04 15:22:10 +09:00
Fabio Estevam
7bcb983feb wandboard: Enable HDMI splashscreen
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-06-03 14:26:14 +02:00
Andrew Gabbasov
0c54f4b7c8 mx6: mx6qsabrelite/nitrogen6x: Remove incorrect setting of gpio CS signal
The number of gpio signal is packed inside CONFIG_SF_DEFAULT_CS macro
(shifted and or'ed with chip select), so it's incorrect to pass
that macro directly as an argument to gpio_direction_output() call.

Also, SPI driver sets the direction and initial value of a gpio,
used as a chip select signal, before any actual activity happens
on the bus.

So, it is safe to just remove the gpio_direction_output call,
that works incorrectly, thus making no effect, anyway.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Tested-by: Robert Winkler <robert.winkler@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
2013-06-03 13:25:46 +02:00
Renato Frias
a1f67807ff mx6qsabreauto: Add Port Expander reset
There are 3 IO expanders on the mx6qsabreauto all reset by the
same GPIO, just set it to high to use the IO.

Signed-off-by: Renato Frias <b13784@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-06-03 13:19:41 +02:00
Renato Frias
195781657c mx6qsabreauto: Add i2c to mx6qsabreauto board
Add i2c2 and 3 to mx6qsabreauto board, i2c3 is multiplexed
use gpio to set steering.

Signed-off-by: Renato Frias <b13784@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-06-03 13:19:11 +02:00
Alison Wang
8c653124a3 arm: vf610: Add basic support for Vybrid VF610TWR board
VF610TWR is a board based on Vybrid VF610 SoC.

This patch adds basic support for Vybrid VF610TWR board.

Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-03 10:56:54 +02:00
Tom Rini
d6639d10db Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2013-05-31 18:28:47 -04:00
Sergey Lapin
dfe64e2c89 mtd: resync with Linux-3.7.1
This patch is essentially an update of u-boot MTD subsystem to
the state of Linux-3.7.1 with exclusion of some bits:

- the update is concentrated on NAND, no onenand or CFI/NOR/SPI
flashes interfaces are updated EXCEPT for API changes.

- new large NAND chips support is there, though some updates
have got in Linux-3.8.-rc1, (which will follow on top of this patch).

To produce this update I used tag v3.7.1 of linux-stable repository.

The update was made using application of relevant patches,
with changes relevant to U-Boot-only stuff sticked together
to keep bisectability. Then all changes were grouped together
to this patch.

Signed-off-by: Sergey Lapin <slapin@ossfans.org>
[scottwood@freescale.com: some eccstrength and build fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2013-05-31 17:12:03 -05:00
Albert ARIBAUD
91607ac17e tx25: copy SPL directly, not using relocate_code.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Simon Glass <sjg@chromium.org>
2013-05-30 20:23:36 +02:00
Albert ARIBAUD
3acb324ff1 mx31pdk: copy SPL directly, not using relocate_code.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Simon Glass <sjg@chromium.org>
2013-05-30 20:23:08 +02:00
Albert ARIBAUD
a19b0dd62d Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	common/cmd_fpga.c
	drivers/usb/host/ohci-at91.c
2013-05-30 14:45:06 +02:00
Tom Warren
dcfe863838 Tegra: T30: Beaver: Fix board/board_name env vars, s/b beaver, not cardhu
Did a 'strings u-boot-dtb-tegra.bin | less' and saw that both
board and board_name == beaver. Didn't test as I have no T30
Beaver board here.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
2013-05-28 12:58:41 -07:00
Shaveta Leekha
6eaeba23dd powerpc/b4860qds: Add LAW Target ID and Create LAW entry for Maple
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:14 -05:00
Shaohui Xie
e14cdc0a69 powerpc/p5040: fix mdio mux for 10G port
Current driver of p5040 assumes 10G port follows 1G port DTSEC5 in
eth port enum structure, it will assign mdio mux depend on this assumption.
This is not true with Fman V3, which added more 1G ports after port DTSEC5
in eth port enum structure, then 10G ports on p5040 will have wrong mdio mux.
So we use dynamic index for 10G ports instead of hardcoded enum value
when doing mdio mux for 10G ports.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:14 -05:00
Shaohui Xie
f9539a9caa powerpc/p2041: fix serdes reference clock frequency display for PC board
PC board has different serdes clock setting with PB board, it uses same
serdes frequency setting on bank2 as on bank1. PC board can be distingushed
from PB board by checking CPLD version, if running on PC board, then fix
the serdes reference clock frequency of bank2.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:13 -05:00
Shaveta Leekha
0fecbba80a powerpc/b4860: fix for Serdes connectivity to SFP's
Crossbar switches were wrongly programmed to
route the CPRI lanes to SFP as the connectivity table
was not correct.
Modified it correctly for SFPs connections.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:13 -05:00
Shengzhou Liu
037e19b812 powerpc/t4240qds: fix PHY reset timeout issue
QSGMII card has different PHY address against previous SGMII card.
We check the type of card in slots and set correct PHY address to
avoid complainning "PHY reset timed out" during u-boot booting up.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:13 -05:00
York Sun
e1379b0730 powerpc/t4qds: Add SW7[4] in the DIP switch display
SW7[4] is the new bit which controls the mapping of eMMC vs SDHC.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:13 -05:00
Suresh Gupta
16d88f415a Enable XAUI interface for B4860QDS
- Added SERDES2 PRTCLs = 0x98, 0x9E
- Default Phy Addresses for Teranetics PHY on XAUI card
	The PHY addresses of Teranetics PHY on XAUI riser card are assigned
	based on the slot it is in. Switches SW4[2:4] and SW6[2:4] on
	AMC2PEX-2S On B4860QDS, AMC2PEX card decide the PHY addresses on slot1
        and slot2
- Configure MDIO for 10Gig Mac

Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:12 -05:00
Stephen George
49e946cb6a board/t4240qds, b4860qds: LAW/TLB for DCSR set to size 32M
Debug trace buffers are memory mapped in DCSR space beyond 4M.

Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:12 -05:00
Shaohui Xie
94025b1cd8 powerpc/p5040: enable PBL tool support
Provided a default RCW for P5040, then it can use PBL to build
ramboot image.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:12 -05:00
Ed Swarthout
f41388159a powerpc/t4qds: use clock measurement for sysclk and ddr clock
Use QIXIS measurement registers to obtain sysclk and ddr clock. This
allows using non-standard clock speeds, set by directly writing to
clock chip or store the values in qixis clock data eeprom.

Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:12 -05:00
Ed Swarthout
428ea86c64 powerpc/qixis: add clock measurement registers
QIXIS includes frequency measurement functions for each major processor
clock input. After reset (and after clocks are stable), QIXIS measures
the clocks against a reference frequency and stores the results in
CLK_FREQ registers. A base register supplies a multiplier which allows
directly obtaining the measured value, without requiring knowledge of
the target system or QIXIS core frequency.

Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:11 -05:00
Shaohui Xie
c79fd50382 T4240/ramboot: enable PBL tool for T4240
Added a default RCW(1_28_6_12) and PBI configure file for T4240, so it can use
PBL tool to produce the ramboot image.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:10 -05:00
York Sun
0aadf4aa51 powerpc/t4240qds: Add VDD override
Allow VDD voltage overriding with a command. This is an add-on feasture of
VID. To override VDD, use command vdd_override with the value of voltage
in mV, for example

vdd_override <voltage in mV, eg. 1050>

The above example will set the VDD to 1.050 volt. Any wrong value out of
range of 0.8188 to 1.2125 volt or invalid string is ignored.

In addition to the command, if overriding VDD is needed earlier in booting
process, save an variable and reboot:

setenv t4240qds_vdd_mv <voltage in mV>
saveenv

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:10 -05:00
York Sun
9cefbd64b2 powerpc/t4240qds: Add board detail for bdinfo command
Print more detail information including core voltage, RCW source, switch
settings, etc. with bdinfo command.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:09 -05:00
Suriyan Ramasami
0ad6c34c3e ARM: Add Seagate GoFlex Home support
Add Seagate GoFlex Home support

Start with dockstar configuration
define support for RTC, DATE, SATA and EXT4FS

Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
2013-05-23 11:59:17 +02:00
Ryan Harkin
cd4f46e1ef ARM: vexpress: create A5 specific board config
This patch creates a new config for the A5 dual core tile that includes the
generic config for the Versatile Express platform.

The generic config has been modified to provide support for the Extended
Memory Map, as used on the A5 core tile.  A5 does not support the legacy
memory map.

Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-05-23 11:22:44 +02:00