Convert CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig, update defconfigs,
headers and whitelist.
Please note that this symbol already was used in Kconfig
(imply in CONFIG_NAND_ATMEL) which did not work, since this symbol was
not available in Kconfig. This changes now with this patch and all
boards with CONFIG_NAND_ATMEL will have BBT enabled. Which is what
I also need on my GARDENA AT91SAM based board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
[trini: Rework such that the configs are unchanged to start with]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ARCH_CPU_INIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>
- remove rk3288 fennec board
- remove SPL raw image support for Rockchip SoCs
- add common misc_init_r() for ethaddr from cpuid
- enable USB HOST support for rk3328
- unify code for finding a valid gpt in part driver
This converts the following to Kconfig:
CONFIG_FSL_USDHC
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_MXS_GPIO
Travis-CI: https://travis-ci.org/lmajewski/u-boot-dfu/builds/571260789
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
This was changed to 1 in commit 0717dde057, but a few months later,
commit 5f9411af37 swapped the order of eMMC and SD card by assigning
indexed aliases to `&sdhci` and `&sdmmc`.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Add signature)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Some ChromeOS devices (atleast veyron speedy) have the first 8MiB of
the eMMC write protected and equipped with a dummy 'IGNOREME' GPT
header - instead of spewing error messages about it, just silently
try the backup GPT.
Note: this does not touch the gpt cmd writing/verifying functions,
those will still complain.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
BRDCFG4[USBOSC] and BRDCFG5[SPR] register field of Qixis device is used
to control SPI and other IP signal routing.
USBOSC:
0= SPI_CLK used as external USB REFCLK input driven with 24.000 MHz.
SPI devices are unusable in this mode.
1= SPI_CLK used as SPI clock.
SPI devices are usable in this mode. USB block is clocked from
internal sources
SPR[3:2]:
SPI_CS / SDHC_DAT4:7 Routing (schematic net CFG_SPI_ROUTE[3:2]):
00= SDHC/eMMC 8-bit
01= SD Card Rev 2.0/3.0
10= SPI on-board memory
11= TDM Riser / SPI off-board connector.
The default value is 00 if an SDCard/eMMC card is selected as the boot
device.
SPR[1:0]:
SPI_SIN/SOUT/SCK Routing (schematic net CFG_SPI_ROUTE[1:0]):
00= SDHC Sync loop
01= TDM Riser / SPI off-board connector.
10= SPI on-board memory.
11= SPI off-board connector.
By default, the SPI feature is not available, so we need to configure
the above register fields to select the route to the SPI feature.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Defines CONFIG_ENV_ADDR for QSPI Boot which specifies the start
address of the flash sector containing the environment. It fixes
the issue that bootcmd is always set as default at bootup.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls1088a platform
does not support dm.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add an implementation of the rtc_enable_32khz_output() that uses the
driver model i2c APIs.
Also put code related to rtc_enable_32khz_output
under CONFIG_RTC_ENABLE_32KHZ_OUTPUT.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls2088a platform
does not support dm.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Since i2c uses dm mode, i2c controller will be initialized when reading
and writing devices on i2c bus. So there is no need for the original
non-dm mode i2c early initialization function call, this patch removed
the definition of CONFIG_SYS_I2C_EARLY_INIT.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls1028a platform
does not support dm.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Move CONFIG_FSL_QSPI from header file to defconfigs,
consequently unset imply config(CONFIG_SPI_FLASH_BAR) which
is not valid for LS series.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
MC firmware need to be aligned to 512M, so minimum 512MB DDR is reserved.
But MC support to work with 128MB or 256MB DDR memory also, in this
case, rest of the memory is not usable.
So reporting this extra memory to Linux through dtb memory fixup.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Since we added clk enable_count and prograte clk child enabling
operation to clk parent, so add a new function sandbox_clk_enable_count
to get enable_count for test usage.
And add test code to get the enable_count after we enable/disable
the device clk.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As what Linux Kernel 5.3.0 provides when enable/disable clk,
there is an enable_count in clk_core_disable/enable. Introduce
enable_count to track the clk enable/disable count when
clk_enable/disable for CCF. And Initialize enable_count to 0 when
register the clk.
And clk tree dump with enable_count will be supported, it will
be easy for us to check the clk status with enable_count
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Now that SPL supports DM_SERIAL and the direct NOR boot supports
DM_SERIAL, the check to see if DM_SERIAL is defined can go away,
because all da850evm variants now support DM_SERIAL. This patch
simply removes some dead precompiler defines.
Signed-off-by: Adam Ford <aford173@gmail.com>
With SPL now supporting DM_SPI, the need for compiler directives
and hard-coded addresses is obsolete. This patch removes some
dead legacy code defining the SPI base address
Signed-off-by: Adam Ford <aford173@gmail.com>
Like we did with 'fit_loadaddr' to 'addr_fit', the variable
'fit_bootfile' contains a name and so should be prefixed with
name_. Make this change here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
This is the first part of a larger effort I would like to propose to
unify and simplify the default set of environment variables.
When many early environment variables were named there were fewer images
being loaded, usually just a kernel. At this time names like 'loadaddr'
would suffice. Now we have more images and many more commands that act on
them, often re-using the same variable for several different uses. The
contents of a variable are also not immediately known causing one to have
to look up a chain of variables to understand what a command is actually
doing. I suggest the following.
To start, all variables containing names should be prefixed with name_
and addresses with addr_. This is like how K2 already does things and
allows for simple universal commands like:
get_fdt_nfs=nfs ${addr_fdt} /boot/${name_fdt}
Which is very clear on what is intended here and would work across all
board that using the this naming convention.
We can do this one variable at a time, start here with addr_fit.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
The variable 'name_overlays' serves the same purpose. Remove
'overlay_files' and use 'name_overlays' everywhere.
Signed-off-by: Andrew F. Davis <afd@ti.com>
- Add ROC-RK3399-PC board support
- Move CONFIG_SPI_FLASH_GIGADEVICE and CONFIG_CMD_USB_MASS_STORAGE to
Kconfig
- using SYSRESET_POWER_OFF for poweroff
(Note that patch for rk8xx pmic is droped for it can not pass Travis
build)
- fix ofnode_get_name() assert
This affects RK3036, RK322X and RK3288 - the defconfig changes done by
moveconfig.py for the veyrons were left out on purpose because they dont
have an OTG port, and will get their config updated in the next commit.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Affects rk3288 veyrons and rk3036, this was mostly done by
moveconfig.py.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the removal of the x86 specific GD flags, there are no arch-
specific GD flags any more. Let's remove the comment about reserving the
upper 16 bits for arch-specific flags in the common header. This gives
us more flexibility with the usage of the GD flags.
As a matter of fact, we are already using more than 16 bits for common
GD flags (with the addition of GD_FLG_WDT_READY).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sometimes an image has multiple CBFS. The current CBFS API is limited to
handling only one at time. Also it keeps track of the CBFS internally in
BSS, which does not work before relocation, for example.
Add a few new functions to overcome these limitations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Move the result variable into the struct also, so that it can be used when
BSS is not available. Add a function to read it.
Note that all functions sill use the BSS version of the data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Use DISTRO_BOOTENV to decouple BOOTENV from CONFIG_DISTRO_DEFAULTS.
Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This pull request provides corrections for the SetVirtualAddress runtime
service and avoids possible calls to NULL by consumers of the
EFI_PXE_BASE_CODE_PROTOCOL.
-----BEGIN PGP SIGNATURE-----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=jIsF
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-10-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc3
This pull request provides corrections for the SetVirtualAddress runtime
service and avoids possible calls to NULL by consumers of the
EFI_PXE_BASE_CODE_PROTOCOL.
U-Boot implements the EFI_PXE_BASE_CODE_PROTOCOL because GRUB uses the mode
information for booting via PXE. All function pointers in the protocol were
NULL up to now which will cause immediate crashes when the services of the
protocol are called.
Create function stubs for all services of the protocol returning
EFI_UNSUPPORTED.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Bring cyclone5 / arria5 / arria10 in line with convention and use
u-boot.img as CONFIG_SPL_FS_LOAD_PAYLOAD_NAME.
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
The current size allocated to U-Boot is 384k, but U-Boot has grown
to 436K which means that saving the environmental variables wipes
out part of the U-Boot source and the board ceases to function.
Due to the sector and erase size for the NOR part and a desire to
not have to change partition sizes often, this patch moves the
U-Boot environmental variables to an offset of 1M so saveenv
does not brick the board. This patch also sets up MTDIDS and
MTDPARTS to clearly show where U-Boot and U-Boot's environmental
variables are located.
Signed-off-by: Adam Ford <aford173@gmail.com>
A previous patch for enabling the NAND config set a flag called
CONFIG_SKIP_LOWLEVEL_INIT when it should have been called
CONFIG_SKIP_LOWLEVEL_INIT_ONLY. The affect this had was creating
a delay on startup for the NOR version which is XIP and doesn't have
SPL, so the lowlevel initialization functions need to operate.
This delay was not really noticeable at first, but the delays have been
getting longer, finally reached the point of nearly seven seconds
before the board would appear to start.
This patch sets the CONFIG_SKIP_LOWLEVEL_INIT_ONLY instead which means
"The normal CP15 init (such as enabling the instruction cache) is still
performed" per the README. It doesn't appear to have any adverse
behavior on the SPI Flash or the NAND flash boards which use SPL.
Fixes: 93f3362762 ("ARM: configs: Add da850evm_nand to boot from NAND")
Signed-off-by: Adam Ford <aford173@gmail.com>
Add needed device-tree nodes to support PCIe 0
and SERDES on AM65x SoC. The nodes are kept
disabled by default.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Current dev_read_*() API lacks support to get address and size
of a "reg" property by name or index. Add support for the same.
Livetree support has been added but not tested on real hardware.
The existing unit tests testing reading address from device-tree
have been updated to test address as well as size.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add support for clk_is_match() which is required to
know if two clock pointers point to the same exact
physical clock.
Also add a unit test for the new API.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This commit adds support for the B&R brsmarc1 SoM.
The SoM is based on TI's AM335x SoC.
Mainly vxWorks 6.9.4.x is running on the board,
doing some PLC stuff on various carrier boards.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
This patch disables DM watchdog support for SPL builds and uses
the legacy omap watchdog driver on TI AM335x chipsets.
The following build error is reported if DM watchdog support was
enabled in SPL:
CC spl/drivers/usb/gadget/rndis.o
LD spl/drivers/usb/gadget/built-in.o
LD spl/drivers/usb/musb-new/built-in.o
LD spl/drivers/built-in.o
LD spl/u-boot-spl
arm-linux-ld.bfd: u-boot-spl section .u_boot_list will not fit in region .sram
arm-linux-ld.bfd: region .sram overflowed by 440 bytes
make[1]: *** [spl/u-boot-spl] Error 1
make: *** [spl/u-boot-spl] Error 2
Adjusted WATCHDOG_RESET macro accordingly. Earlier it was pointing
to hw_watchdog_reset. Since CONFIG_WATCHDOG replaces CONFIG_HW_WATCHDOG,
now WATCHDOG_RESET macro points to watchdog_reset. This watchdog_reset
is not defined anywhere for am33xx/omap2 and needs to be defined. Fixed
this by simply calling hw_watchdog_reset in watchdog_reset.
Built and tested on AM335x device (BeagleboneBlack), compile tested for
all other AM33xx/omap2 based boards.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
[trini: Fix watchdog.h logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
The SEI510 board is based on the Amlogic S905X2 SoC
from the Amlogic G12A SoC family.
The board has the following specifications :
- Amlogic S905X2 ARM Cortex-A53 quad-core SoC
- XGB DDR4 SDRAM
- 10/100 Ethernet (Internal PHY)
- 1 x USB 3.0 Host
- eMMC
- SDcard
- Infrared receiver
- SDIO WiFi Module
The board default behaviour is for booting Android and triggers
fastboot on recovery or reboot mode.
USB vendor ID (used by fastboot) is 0x18d1 (Google) for
default udev rules for existing android users work out of the box.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This board is unmaintained and can be removed. This also allows us to
remove kmp204x-common.h and integrate it in kmp204x.h.
Signed-off-by: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove the PORTL2 board and all its dependencies as it is no longer
supported by the company.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Activate the driver model for the Ethernet interface (RGMII) in the KM
Kirkwood Kconfig file. Additionally, raise the auto negotiation timeout
to eight seconds as more time is required for those boards.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Activate the driver model for the serial interface in the KM Kirkwood
Kconfig file. The associated preprocessor definitions could be removed
from the header file. However, the clock of 200 MHz needs to be declared
in the device tree.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
A typo in the km_kirkwood.h header prevented to undefine the initialization
of the Kirkwood PCIe interface.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
After moving the KM specific configurations to Kconfig, the associated
preprocessor definitions can now be removed in the headers. Moreover, the
whitelist has been adapted correspondingly.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
To execute the conversion away from board specific header files, Kconfig
menus have been implemented for all KM boards and additionally for those
having an ARM architecture.
For the moment, the preprocessor definitions stay in the headers. The
boolean types, however, needed a modification (#define CONFIG_* 1).
The default configuration files of some boards required an update in order
to not change the currently defined values of the configurations.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This file has quite a lot of general definitions and include files. Add a
note about our intent to remove more of this.
The file should ultimately include the configuration and perhaps a very
other very common things used by most U-Boot files.
Signed-off-by: Simon Glass <sjg@chromium.org>
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.
Rename this file and add a comment at the top to indicate its internal
nature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
This declaration is only used in three files. Although it relates to
malloc() it is actually only used during malloc() init. It uses CONFIG
options including CONFIG_ENV_ADDR which are defined only in environment.h
so this header must be included anyway, for TOTAL_MALLOC_LEN to be
correct.
Nove it to environment.h to simplify the common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
There doesn't seem to be any good reason for using __ in the arguments in
this header file. A double underscore is usually reserved for compiler
features.
Drop these and remove the unnecessary 'extern' as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Avoid using a typedef here which is unnecessary. Add an 'env_' prefix to
both the enum and its members to make it clear that these are related to
the environment.
Add an ENV prefix to these two flags so that it is clear what they relate
to. Also move them to env.h since they are part of the public API. Use an
enum rather than a #define to tie them together.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an ENV prefix to these two flags so that it is clear what they relate
to. Also move them to env.h since they are part of the public API. Use an
enum rather than a #define to tie them together.
Signed-off-by: Simon Glass <sjg@chromium.org>
This typedef does not need to be defined in the search.h header since it
is only used in one file (hashtable.c). Remove it from the header and
change it to a struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
U-Boot is not supposed to use typedef for structs anymore. Also this name
is the same as the ENTRY() macro used in assembler files, and 'entry'
itself is widely used in U-Boot (>8k matches).
Drop the typedef and rename the struct to env_entry to reduce confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
These definitions are effectively part of the 'public' API of the
environment implementation since they do not require access to any
internal variables. Move them to the env.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This enum is somewhat widely used to determine if the environment is valid
or not. Move it to the common environment header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The name 'environment' is widely used in U-Boot so is not a very useful
name of a variable. Rename it to better indicate its purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Move these functions to the new header file and rename set_default_env()
to env_set_default() so that it has a consistent env_ prefix.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is not defined or used in U-Boot. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move this function to the new header file and rename it so it has an env_
prefix.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This function fits better with the network subsystem, so move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Joe Hershberger <joe.hershberger@ni.com>
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move envmatch() over to the new header file. Also rename it to env_match()
to better line up with other functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move this function over to the new header file. Also rename it to have an
env_ prefix like the other functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
At present we have environment.h but this file includes all the
environment-related header files as well as internals such as
default_environment.
It seems desirable to have a new header to hold the commonly used
environment functions, so that most files can avoid including all of this
unnecessary stuff.
Create a new env.h header and move one function over to it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This function relates to lcd.h and is about to become obsolete with the
driver-model conversion. Move it out of common.h
Signed-off-by: Simon Glass <sjg@chromium.org>
These declarations are not used anymore, so drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
As part of the effort to remove things from common.h, create a new header
for the gzip functions. Move the function declarations to it and add
missing documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This commit adds board support for Hikey960 board from Hisilicon. This
board is one of the Consumer Edition boards of the 96Boards family
powered by Kirin960 SoC.
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/hikey960/
The initial supported/tested devices include:
- Debug serial
- SD
With these support, it's good enough for loading Linux Kernel from SD.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
- Enable SD slot on Intel Edison
- Populate CSRT ACPI table for shared DMA controller on Intel Tangier
- Convert Intel ICH-SPI driver to use new spi-mem ops
- Enable config_distro_bootcmd for QEMU x86
- Support U-Boot as a payload for Intel Slim Bootloader
- Avoid writing temporary asl files into the source tree which fixes the
parallel build issue occasionally seen
Import R8A77980 V3H DTs and headers from Linux 5.2.7 , commit 5697a9d3d55f.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Remove obsolete legacy usbboot wrapper, as distroboot can handle
booting from USB drivers.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Support the V1.2 hardware revision with the following pin muxing
changes:
Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4
are now used as DDC pins.
Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are
now used as USB power enable signals.
Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power
enable signals are now used as GPIO3 and GPIO4.
Additionally a new device tree file tegra124-apalis-v1.2-eval.dtb is
loaded on V1.2 and later modules and resp. USB power enable signals
activated.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Remove video=tegrafb0:640x480-16@60 aka VESA VGA mode from vidargs in
order for the panel specification in the device tree to be used. This
causes the default to be the 10.1" LVDS display which will be available
in the Toradex webshop shortly.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Switch to the generic compressed Kernel image type (zImage) instead of
the U-Boot specific uImage format.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Let the kernel print some debug messages when a user program
crashes due to an exception.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add slimbootloader board to run U-boot as a Slim Bootloader payload
- Add new board/intel/slimbootloader directory with minimum codes
- Add slimbootloader configuration files
- Add doc/board/intel/slimbootloader.rst
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add slimbootloader board MAINTAINERS file]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
With qemu-x86 starting to use config_distro_bootcmd, the pre-defined
ramboot and nfsboot commands do not work any more. This is caused by
undefined environment variable 'ramdiskaddr' that was previously set
in CONFIG_EXTRA_ENV_SETTINGS but later CONFIG_EXTRA_ENV_SETTINGS was
redefined for distro boot.
Update the x86 generic CONFIG_EXTRA_ENV_SETTINGS to consider distro
boot, and remove the one in qemu-x86.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Converts qemu x86 machines to boot using distro_config. The intent is to
allow u-boot in qemu to be maximally compatible with many boot methods
without having to change the config. Previously, u-boot would only boot
in a very limited set of circumstances where there was a /boot/vmlinuz
on scsi 0:3 with no ramdisk.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: convert doc updates to reST]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This takes the latest changes from AOSP from the file
include/bootimg/bootimg.h from the repository:
https://android.googlesource.com/platform/system/tools/mkbootimg
and update the U-Boot version with the latest changes.
This file keeps the changes from AOSP to a minimum:
* Comments were converted from C++ to C style.
* Code inside __cplusplus #ifdef blocks were removed.
* C++11 struct extensions replaced with a single struct.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
This adds missing hifsys reset parts in header files.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Provide a concise description of the assert() macro. Point out that the
tested expression is always executed, irrespective of the value of _DEBUG.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
With this pull request a workaround for GRUB on 32bit ARM is re-enabled
and made customizable. Without the patch booting on ARM 32bit with GRUB
prior to version 2.04 or with a cache which is not managed via CP15
fails.
Further work will be needed to achieve a UEFI compliant cache handling.
According to the UEFI spec all caches except those that cannot be
managed via CP15 should be enabled.
An implementation of the ConvertPointer() runtime service is provided.
efi_crt0 is always rebuild to avoid having to call 'make mrproper' when
switching architectures.
-----BEGIN PGP SIGNATURE-----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=jfh5
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-10-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc2
With this pull request a workaround for GRUB on 32bit ARM is re-enabled
and made customizable. Without the patch booting on ARM 32bit with GRUB
prior to version 2.04 or with a cache which is not managed via CP15
fails.
Further work will be needed to achieve a UEFI compliant cache handling.
According to the UEFI spec all caches except those that cannot be
managed via CP15 should be enabled.
An implementation of the ConvertPointer() runtime service is provided.
efi_crt0 is always rebuild to avoid having to call 'make mrproper' when
switching architectures.
Add comments for this function. Also remove the #ifdef around it so that
it can be called from 'if (IS_ENABLED(...))'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since this is part of the autoboot functionality, it makes sense to name
it with an AUTOBOOT prefix. No mainline boards use it so this should be
safe, and downstream boards will need to adjust.
Since this option is just an integer value, it really needs another option
to control whether the feature is enabled or not. Add a new
CONFIG_USE_AUTOBOOT_MENUKEY for that. This fits better with how things are
done with Kconfig, avoiding the need to use a specific value to disable
the feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT
Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.
Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.
Signed-off-by: Simon Glass <sjg@chromium.org>
In order to use CONFIG_PREBOOT with Kconfig, CONFIG_USE_PREBOOT must be
defined for each board. To prepare for conversion to Kconfig, add this.
Signed-off-by: Simon Glass <sjg@chromium.org>
- add support for 4GiB DRAM memory
- add support for Amlogic G12B based Odroid-N2
- small duplicate logic fix for gxbb clock driver
-----BEGIN PGP SIGNATURE-----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=Q5fc
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20190731' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- sync Amlogic G12A DT with linux 5.3-rc1
- add support for 4GiB DRAM memory
- add support for Amlogic G12B based Odroid-N2
- small duplicate logic fix for gxbb clock driver
In case of Android boot, reboot reason can be written into BCB (usually
it's an area in 'misc' partition). U-Boot then can obtain that reboot
reason from BCB and handle it accordingly to achieve correct Android
boot flow, like it was suggested in [1]:
- if it's empty: perform normal Android boot from eMMC
- if it contains "bootonce-bootloader": get into fastboot mode
- if it contains "boot-recovery": perform recovery boot
The latter is not implemented yet, as it depends on some features that
are not implemented on TI platforms yet (in AOSP and in U-Boot).
[1] https://marc.info/?l=u-boot&m=152508418909737&w=2
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Import HardKernel Odroid-N2 DT from Linux 5.3-rc1, commit 5f9e832c1370
("Linus 5.3-rc1") based on an Amlogic G12B S922X SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Sync the Amlogic Meson G12A DT and Bindings file with the Linux 5.3-rc1
from the commit 5f9e832c1370 ("Linus 5.3-rc1").
Also remove the meson-g12a-u-boot.dtsi and meson-g12a-u200-u-boot.dtsi,
now conflicting with the main DT content.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
When support Clock Common Framework, U-Boot use dev for
clk tree information, there is no clk->parent. When
support composite clk, it contains mux/gate/divider,
but the mux/gate/divider is not binded with device.
So we could not use dev_get_uclass_priv to get the correct
clk_mux/gate/divider. So add clk_dev_binded to let
choose the correct method.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
- extend mxc_ipuv3_fb to enable backlight/display
- include fb_base in global_data for DM_VIDEO
- show frame buffer address via board info
as used to be with legacy VIDEO support
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXUCEtQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXLYhAJ4gSCCx54ubBmbsZ1cueGk59E/SkwCdFl7nfLqz
Vy/HbBVAUkzD4JVOR0U=
=7rSM
-----END PGP SIGNATURE-----
Merge tag 'video-for-2019.10-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix EDID mode filtering
- extend mxc_ipuv3_fb to enable backlight/display
- include fb_base in global_data for DM_VIDEO
- show frame buffer address via board info
as used to be with legacy VIDEO support
fpga:
- Xilinx virtex2 cleanup
- Altera cyclon2 cleanup
zynq:
- Minor Kconfig cleanup
- Add psu_init configuration for Z-turn board
zynqmp:
- Add support for pmufw config passing to PMU
- script for psu_init conversion
- zcu1275 renaming
xilinx:
- Add support for UltraZed-EV SoM
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXUBgGwAKCRDKSWXLKUoM
IcJJAKCUoHRpqNgcZUiE10D9/VhZ3bUVtwCgi0fzSlqgHVG2EzApfqN+2KfrGJo=
=7i0K
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx/FPGA changes for v2019.10
fpga:
- Xilinx virtex2 cleanup
- Altera cyclon2 cleanup
zynq:
- Minor Kconfig cleanup
- Add psu_init configuration for Z-turn board
zynqmp:
- Add support for pmufw config passing to PMU
- script for psu_init conversion
- zcu1275 renaming
xilinx:
- Add support for UltraZed-EV SoM
Use efi_uintn_t where the UEFI spec uses UINTN. Use efi_uintn_t also for
the result of the division of two efi_uintn_t.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In cmd/fpga.c the commands should return enum command_ret_t, e.g.
CMD_RET_USAGE, CMD_RET_SUCCESS, or CMD_RET_FAILURE. What they actually
do is passing a return value from different 'fpga_' functions.
Passing on a return value of -1 from a called function leads to printing
out usage text. In case of actually correct usage with correctly
specified parameters but some fail at runtime printing out that usage
text is distracting.
The reason is most 'fpga_' functions return either FPGA_SUCCESS or
FPGA_FAIL, the latter was equal to -1 which is the same value as
CMD_RET_USAGE. So just passing on FPGA_FAIL lead to printing out usage.
We should only return CMD_RET_USAGE in cases, where the user sent wrong
input. Every other case should return CMD_RET_SUCCESS or
CMD_RET_FAILURE, and not simply pass an error code.
Simply changing FPGA_FAIL from -1 to 1 gets the job done.
Suggested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Alexander Dahl <ada@thorsis.com>
There seems to be only one place, where this is checked against:
`altera_validate()`. It should be non zero. Otherwise it is only used to
display it, so it probably does not really matter at the moment. But we
had the datasheet open anyway …
Sizes in datasheet are bit counts, display here is in bytes.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
This adds support for slave serial programming, in addition to the
previously supported slave SelectMAP mode. There are two ways that this
can be used:
-Using the clk and wdata callbacks in order to write image data one bit
at a time using pure bit-banging. This works, but is rather painfully
slow with typical image sizes.
-By specifying the wbulkdata callback instead, the image loading process
can be offloaded to SPI hardware. In this mode the clk and wdata
callbacks do not need to be specified. This allows the image to be
loaded much faster, taking only a few seconds with even relatively large
images.
Slave serial programming has been tested on the Kintex-7 series of
FPGAs.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This Kbuild option disappeared way back in 2014:
commit 75504e9592
Author: Mateusz Zalega <m.zalega@samsung.com>
Date: Wed Apr 30 13:07:48 2014 +0200
... snip ...
CONFIG_USB_CABLE_CHECK was removed.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
