As part of the effort to remove things from common.h, create a new header
for the gzip functions. Move the function declarations to it and add
missing documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This commit adds board support for Hikey960 board from Hisilicon. This
board is one of the Consumer Edition boards of the 96Boards family
powered by Kirin960 SoC.
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/hikey960/
The initial supported/tested devices include:
- Debug serial
- SD
With these support, it's good enough for loading Linux Kernel from SD.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
- Enable SD slot on Intel Edison
- Populate CSRT ACPI table for shared DMA controller on Intel Tangier
- Convert Intel ICH-SPI driver to use new spi-mem ops
- Enable config_distro_bootcmd for QEMU x86
- Support U-Boot as a payload for Intel Slim Bootloader
- Avoid writing temporary asl files into the source tree which fixes the
parallel build issue occasionally seen
Import R8A77980 V3H DTs and headers from Linux 5.2.7 , commit 5697a9d3d55f.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Remove obsolete legacy usbboot wrapper, as distroboot can handle
booting from USB drivers.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Support the V1.2 hardware revision with the following pin muxing
changes:
Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4
are now used as DDC pins.
Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are
now used as USB power enable signals.
Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power
enable signals are now used as GPIO3 and GPIO4.
Additionally a new device tree file tegra124-apalis-v1.2-eval.dtb is
loaded on V1.2 and later modules and resp. USB power enable signals
activated.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Remove video=tegrafb0:640x480-16@60 aka VESA VGA mode from vidargs in
order for the panel specification in the device tree to be used. This
causes the default to be the 10.1" LVDS display which will be available
in the Toradex webshop shortly.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Switch to the generic compressed Kernel image type (zImage) instead of
the U-Boot specific uImage format.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Let the kernel print some debug messages when a user program
crashes due to an exception.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add slimbootloader board to run U-boot as a Slim Bootloader payload
- Add new board/intel/slimbootloader directory with minimum codes
- Add slimbootloader configuration files
- Add doc/board/intel/slimbootloader.rst
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add slimbootloader board MAINTAINERS file]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
With qemu-x86 starting to use config_distro_bootcmd, the pre-defined
ramboot and nfsboot commands do not work any more. This is caused by
undefined environment variable 'ramdiskaddr' that was previously set
in CONFIG_EXTRA_ENV_SETTINGS but later CONFIG_EXTRA_ENV_SETTINGS was
redefined for distro boot.
Update the x86 generic CONFIG_EXTRA_ENV_SETTINGS to consider distro
boot, and remove the one in qemu-x86.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Converts qemu x86 machines to boot using distro_config. The intent is to
allow u-boot in qemu to be maximally compatible with many boot methods
without having to change the config. Previously, u-boot would only boot
in a very limited set of circumstances where there was a /boot/vmlinuz
on scsi 0:3 with no ramdisk.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: convert doc updates to reST]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This takes the latest changes from AOSP from the file
include/bootimg/bootimg.h from the repository:
https://android.googlesource.com/platform/system/tools/mkbootimg
and update the U-Boot version with the latest changes.
This file keeps the changes from AOSP to a minimum:
* Comments were converted from C++ to C style.
* Code inside __cplusplus #ifdef blocks were removed.
* C++11 struct extensions replaced with a single struct.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
This adds missing hifsys reset parts in header files.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Provide a concise description of the assert() macro. Point out that the
tested expression is always executed, irrespective of the value of _DEBUG.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
With this pull request a workaround for GRUB on 32bit ARM is re-enabled
and made customizable. Without the patch booting on ARM 32bit with GRUB
prior to version 2.04 or with a cache which is not managed via CP15
fails.
Further work will be needed to achieve a UEFI compliant cache handling.
According to the UEFI spec all caches except those that cannot be
managed via CP15 should be enabled.
An implementation of the ConvertPointer() runtime service is provided.
efi_crt0 is always rebuild to avoid having to call 'make mrproper' when
switching architectures.
-----BEGIN PGP SIGNATURE-----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=jfh5
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-10-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc2
With this pull request a workaround for GRUB on 32bit ARM is re-enabled
and made customizable. Without the patch booting on ARM 32bit with GRUB
prior to version 2.04 or with a cache which is not managed via CP15
fails.
Further work will be needed to achieve a UEFI compliant cache handling.
According to the UEFI spec all caches except those that cannot be
managed via CP15 should be enabled.
An implementation of the ConvertPointer() runtime service is provided.
efi_crt0 is always rebuild to avoid having to call 'make mrproper' when
switching architectures.
Add comments for this function. Also remove the #ifdef around it so that
it can be called from 'if (IS_ENABLED(...))'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since this is part of the autoboot functionality, it makes sense to name
it with an AUTOBOOT prefix. No mainline boards use it so this should be
safe, and downstream boards will need to adjust.
Since this option is just an integer value, it really needs another option
to control whether the feature is enabled or not. Add a new
CONFIG_USE_AUTOBOOT_MENUKEY for that. This fits better with how things are
done with Kconfig, avoiding the need to use a specific value to disable
the feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT
Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.
Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.
Signed-off-by: Simon Glass <sjg@chromium.org>
In order to use CONFIG_PREBOOT with Kconfig, CONFIG_USE_PREBOOT must be
defined for each board. To prepare for conversion to Kconfig, add this.
Signed-off-by: Simon Glass <sjg@chromium.org>
- add support for 4GiB DRAM memory
- add support for Amlogic G12B based Odroid-N2
- small duplicate logic fix for gxbb clock driver
-----BEGIN PGP SIGNATURE-----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=Q5fc
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20190731' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- sync Amlogic G12A DT with linux 5.3-rc1
- add support for 4GiB DRAM memory
- add support for Amlogic G12B based Odroid-N2
- small duplicate logic fix for gxbb clock driver
In case of Android boot, reboot reason can be written into BCB (usually
it's an area in 'misc' partition). U-Boot then can obtain that reboot
reason from BCB and handle it accordingly to achieve correct Android
boot flow, like it was suggested in [1]:
- if it's empty: perform normal Android boot from eMMC
- if it contains "bootonce-bootloader": get into fastboot mode
- if it contains "boot-recovery": perform recovery boot
The latter is not implemented yet, as it depends on some features that
are not implemented on TI platforms yet (in AOSP and in U-Boot).
[1] https://marc.info/?l=u-boot&m=152508418909737&w=2
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Import HardKernel Odroid-N2 DT from Linux 5.3-rc1, commit 5f9e832c1370
("Linus 5.3-rc1") based on an Amlogic G12B S922X SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Sync the Amlogic Meson G12A DT and Bindings file with the Linux 5.3-rc1
from the commit 5f9e832c1370 ("Linus 5.3-rc1").
Also remove the meson-g12a-u-boot.dtsi and meson-g12a-u200-u-boot.dtsi,
now conflicting with the main DT content.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
When support Clock Common Framework, U-Boot use dev for
clk tree information, there is no clk->parent. When
support composite clk, it contains mux/gate/divider,
but the mux/gate/divider is not binded with device.
So we could not use dev_get_uclass_priv to get the correct
clk_mux/gate/divider. So add clk_dev_binded to let
choose the correct method.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
- extend mxc_ipuv3_fb to enable backlight/display
- include fb_base in global_data for DM_VIDEO
- show frame buffer address via board info
as used to be with legacy VIDEO support
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXUCEtQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXLYhAJ4gSCCx54ubBmbsZ1cueGk59E/SkwCdFl7nfLqz
Vy/HbBVAUkzD4JVOR0U=
=7rSM
-----END PGP SIGNATURE-----
Merge tag 'video-for-2019.10-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix EDID mode filtering
- extend mxc_ipuv3_fb to enable backlight/display
- include fb_base in global_data for DM_VIDEO
- show frame buffer address via board info
as used to be with legacy VIDEO support
fpga:
- Xilinx virtex2 cleanup
- Altera cyclon2 cleanup
zynq:
- Minor Kconfig cleanup
- Add psu_init configuration for Z-turn board
zynqmp:
- Add support for pmufw config passing to PMU
- script for psu_init conversion
- zcu1275 renaming
xilinx:
- Add support for UltraZed-EV SoM
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXUBgGwAKCRDKSWXLKUoM
IcJJAKCUoHRpqNgcZUiE10D9/VhZ3bUVtwCgi0fzSlqgHVG2EzApfqN+2KfrGJo=
=7i0K
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx/FPGA changes for v2019.10
fpga:
- Xilinx virtex2 cleanup
- Altera cyclon2 cleanup
zynq:
- Minor Kconfig cleanup
- Add psu_init configuration for Z-turn board
zynqmp:
- Add support for pmufw config passing to PMU
- script for psu_init conversion
- zcu1275 renaming
xilinx:
- Add support for UltraZed-EV SoM
Use efi_uintn_t where the UEFI spec uses UINTN. Use efi_uintn_t also for
the result of the division of two efi_uintn_t.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In cmd/fpga.c the commands should return enum command_ret_t, e.g.
CMD_RET_USAGE, CMD_RET_SUCCESS, or CMD_RET_FAILURE. What they actually
do is passing a return value from different 'fpga_' functions.
Passing on a return value of -1 from a called function leads to printing
out usage text. In case of actually correct usage with correctly
specified parameters but some fail at runtime printing out that usage
text is distracting.
The reason is most 'fpga_' functions return either FPGA_SUCCESS or
FPGA_FAIL, the latter was equal to -1 which is the same value as
CMD_RET_USAGE. So just passing on FPGA_FAIL lead to printing out usage.
We should only return CMD_RET_USAGE in cases, where the user sent wrong
input. Every other case should return CMD_RET_SUCCESS or
CMD_RET_FAILURE, and not simply pass an error code.
Simply changing FPGA_FAIL from -1 to 1 gets the job done.
Suggested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Alexander Dahl <ada@thorsis.com>
There seems to be only one place, where this is checked against:
`altera_validate()`. It should be non zero. Otherwise it is only used to
display it, so it probably does not really matter at the moment. But we
had the datasheet open anyway …
Sizes in datasheet are bit counts, display here is in bytes.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
This adds support for slave serial programming, in addition to the
previously supported slave SelectMAP mode. There are two ways that this
can be used:
-Using the clk and wdata callbacks in order to write image data one bit
at a time using pure bit-banging. This works, but is rather painfully
slow with typical image sizes.
-By specifying the wbulkdata callback instead, the image loading process
can be offloaded to SPI hardware. In this mode the clk and wdata
callbacks do not need to be specified. This allows the image to be
loaded much faster, taking only a few seconds with even relatively large
images.
Slave serial programming has been tested on the Kintex-7 series of
FPGAs.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This Kbuild option disappeared way back in 2014:
commit 75504e9592
Author: Mateusz Zalega <m.zalega@samsung.com>
Date: Wed Apr 30 13:07:48 2014 +0200
... snip ...
CONFIG_USB_CABLE_CHECK was removed.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Now that we have enabled the driver-model in SPL, we can remove the
code disabling NAND self-init in SPL from the config include for
omapl138-lcdk.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Enable the driver-model on da850-evm. We need to add a dummy nand node
to the device tree, as the real nand node is a sub-node of the aemif
device.
On linux the aemif driver populates all its child nodes, but we can't do
it in u-boot currently.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Enable the driver-model on da850-lcdk. We need to add a dummy nand node
to the device tree, as the real nand node is a sub-node of the aemif
device.
On linux the aemif driver populates all its child nodes, but we can't do
it in u-boot currently.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There are no more users of the compatibility layer for i2c. Remove the
driver and all references to it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
This option is no longer used on any davinci board but still selected
in defconfigs which causes the following warning:
===================== WARNING ======================
This board uses CONFIG_DM_I2C_COMPAT. Please remove
(possibly in a subsequent patch in your series)
before sending patches to the mailing list.
====================================================
Remove all references to CONFIG_DM_I2C_COMPAT from davinci.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
The pumpkin board is made by Gossamer Engineering and is using
a MediaTek SoC. The board currently comes in two available version:
MT8516 SoC and MT8167 SoC.
The board provides the following IOs: eMMC, NAND, SD card, USB type-A,
Ethernet, Wi-Fi, Bluetooth, Audio (jack out, 2 PDM port, 1 analog in),
serial over USB, and an expansion header.
Additionally there is a HDMI port, DSI port, and camera port only
on the MT8167 version of the board.
The board can be powered by battery and/or via a USB Type-C port and
is using a PMIC MT6392.
The eMMC and NAND are sharing pins and cannot be used together.
This commit is adding the basic boot support for the Pumpkin MT8516
board on the eMMC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
recently added gpio hog patch was "in discussion"
state with Simon Glass. This patch now adds most
of comments from Simon Glass.
Signed-off-by: Heiko Schocher <hs@denx.de>
Upcoming patches want to add decompression to use cases that are no
longer directly related to booting. It makes sense to retain a single
decompression routine, but it should no longer be in bootm.c (which is
not compiled for all configurations). This patch moves
bootm_decomp_image() to image.c and renames it to image_decomp() in
preparation of those upcoming patches.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fix warning around handle_decomp_error being unused]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Clean up and migrate to use common rockchip spl board file
- Clean up and migrate to use common rockchip board file
- Increase rk3288 CONFIG_SYS_BOOTM_LEN to 16MB
Add the CONFIG_ROCKCHIP_STIMER_BASE so that we can use the stimer
init function in tpl.c and spl.c
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the ddc-i2c-bus device tree property which allows
for using an external i2c master for reading the display's EDID.
Signed-off-by: Niklas Schulze <me@jns.io>
Introduce a new display op, mode_valid() to be used with the newly
introduced edid_get_timing_validate() function, to filter supported
monitor timings if handled by the display driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The original edid_get_timing() function returns the first valid timing,
but on some plaforms, we could only supports a subset of the listed
monitot's navite timing.
Let's introduce a edid_get_timing_validate() adding a mode_valid callback
including a private cookie pointer.
If the callback returns false, the current timing is discared and the next
one is checked. If no valid & supported timings are found, the function
would return an error.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
1. This fixes linking issues when building with DM_VIDEO enabled mxsfb
driver.
2. Provide proper defines for both VIDEO=y and DM_VIDEO=y.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Move dcu-related code to fsl_dcu_probe_common, keep in video_hw_init()
only legacy video stack (filling GraphicPanel struct etc.).
Add wrappers for all init functions, that will let to provide
struct fb_info as an additional param (needed for further moving it from
the global scope to driver private data struct in DM converted driver).
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
ttyO2 console enables legacy CONFIG_SERIAL_OMAP driver in kernel.
Nowadays it's preferred to use the generic CONFIG_SERIAL_8250_OMAP
driver, which being enabled via ttyS2 console. Both drivers are enabled
in multi_v7_defconfig and in omap2plus_defconfig, for compatibility
reasons. Let's switch to ttyS2 console, to be sure that standard 8250
serial driver is used.
Similar behavior can be also achieved by enabling
CONFIG_SERIAL_8250_OMAP_TTYO_FIXUP option in kernel, but it's better not
to rely on that, as it can be disabled or removed after transitional
period.
Right now on DRA7/AM57x platforms the 8250-omap driver is being probed
first, and omap-serial driver is only probed if the first one failed.
It can be seen from uart3 definition in arch/arm/boot/dts/dra7-l4.dtsi:
compatible = "ti,dra742-uart", "ti,omap4-uart";
So the kernel already uses 8250 driver. This change basically allows
kernel developers to throw away the omap-serial driver and associated
compatibility options. Similar discussions [1,2] have started several
years ago, so it should be safe to do that now.
[1] https://patchwork.kernel.org/patch/6198471/
[2] http://processors.wiki.ti.com/index.php/Sitara_Linux_UART_-_Switching_to_8250_Driver
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Andrew F. Davis <afd@ti.com>
[trini: Update omap5_uevm]
Signed-off-by: Tom Rini <trini@konsulko.com>
linux-mainline with multi_v7_defconfig + Android configs takes more
space than regular TI Android kernel and bootm will fail to load it.
Let's increase max kernel size up to 64 MiB to make it possible to run
such kernel.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The DA8850-evm supports DM_I2C and boots with SPL_DM, so we can
drop some of the code which disables DM_I2C in SPL. This
patch removes some #undef's now rendered obsolete.
Signed-off-by: Adam Ford <aford173@gmail.com>
OHCI was added with DM_USB support, so there are a few unneeded
items in the header file that can be removed. This also
unifies da850evm with NOR and NAND booting options so all have
OHCI support.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Migrate da850_am18xxevm]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch enables the pinmuxing to support gpio_57 for phy reset
and fixes the pinmuxing for the ECHI tranceiver. The clocks
don't appear to by fully enabled yet, so OMAP-EHCI on am3517 is
still not yet working, but we're one step closer.
Signed-off-by: Adam Ford <aford173@gmail.com>
The SOM-LV boards support the OMAP EHCI driver using port 2.
With the driver updated to support device tree, this patch sets
the corresponding pin muxing for the tranceiver as well as the
reset pin.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add pinctrl macros for J721E SoC. These macro definitions are
similar to that of AM6, but adding new definitions to avoid
any naming confusions in the soc dts files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
TISCI protocol supports for enabling the device either with exclusive
permissions for the requesting host or with sharing across the hosts.
There are certain devices which are exclusive to Linux context and
there are certain devices that are shared across different host contexts.
So add support for getting this information from DT by increasing
the power-domain cells to 2.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Certain drivers want to attach private data corresponding to each
power domain. This data might be specific be to the drvier. So add
a priv entry into the power_domain structure.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Any host while requesting for a device can request for its exclusive
access. If an exclusive permission is obtained then it is the host's
responsibility to release the device before the software entity on
the host completes its execution. Else any other host's request for
the device will be nacked. So add a command that releases all the
exclusive devices that is acquired by the current host. This should
be used with utmost care and can be called only at the end of the
execution.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add and expose a new processor shutdown API that wraps the two TISCI
messages involved in initiating a core shutdown. The API will first
queue a message to have the DMSC wait for a certain processor boot
status to happen followed by a message to trigger the actual shutdown-
with both messages being sent without waiting or requesting for a
response. Note that the processor shutdown API call will need to be
followed up by user software placing the respective core into either
WFE or WFI mode.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Sysfw provides an option for requesting exclusive access for a
device using the flags MSG_FLAG_DEVICE_EXCLUSIVE. If this flag is
not used, the device is meant to be shared across hosts. Once a device
is requested from a host with this flag set, any request to this
device from a different host will be nacked by sysfw. Current tisci
driver enables this flag for every device requests. But this may not
be true for all the devices. So provide a separate commands in driver
for exclusive and shared device requests.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Rockchip SoCs have internal sram for bootrom data area and for
sdram init program space. Introduce the base address in case
we need to use it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The CONFIG_SYS_NS16550_MEM32 already defined in
rockchip_common.h, no need to define again in soc
level header.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The default value of CONFIG_SYS_BOOTM_LEN is 0x800000 i.e, 8MB which
causes board reset because of larger uImage size.
This was tested on rk3288 Amarula Vyasa and rk3288 Asus Tinker
boards.
Error log snippet:
Booting using the fdt blob at 0x1f00000
Loading Kernel Image ... Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
resetting ...
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Now that we removed all legacy boards selecting TI_EMAC we can
completely convert the driver code to using the driver model.
This patch also updates all remaining users of davinci_emac.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #am3517-evm & da850-evm
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
We typically use same set of distro images (yocto, debian, fedora, etc.)
on both QEMU RISC-V virt machine and SiFive Unleashed board.
With growing kernel and ramdisk images, we need to re-adjust default
U-Boot environment variables. The config header for QEMU RISC-V virt
machine has been already updated to handle bigger kernel and ramdisk
images hence this patch updates SiFive FU540 config header accordingly.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Tested-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.
It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.
Supported boot media: microSD card (via SPL), QSPI flash.
Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which
is 64 MB in size and has an erase sector size of 256KB (therefore,
flashing the RCW would erase part of U-Boot).
Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which
is only 32 MB in size but has an erase sector size of 64KB (therefore
the RCW image can be flashed without erasing U-Boot).
To avoid the problems above, the U-Boot base address has been selected
at 0x100000 (the start of the 5th 256KB erase sector), which works for
all board revisions. Actually 0x40000 would have been enough, but
0x100000 is common for all Layerscape devices.
eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but
SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is
disabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Jianchao Wang <jianchao.wang@nxp.com>
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
[Vladimir] Code taken from https://github.com/openil/u-boot (which
itself is mostly copied from ls1021a-iot) and adapted with the following
changes:
- Add a008850 errata workaround
- Converted eTSEC, MMC to DM to avoid all build warnings
- Plugged in distro boot feature, including support for extlinux.conf
- Added defconfig for QSPI boot
- Added the board/freescale/ls1021atsn/README.rst for initial setup
- Increased CONFIG_SYS_MONITOR_LEN so that the SPL malloc pool does not
get overwritten during copying of the u-boot.bin payload from MMC to
DDR.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Due to a typo, "run qspi_bootcmd" and "env exists secureboot" got
concatenated instead of being separated by a semicolon.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now that we have added driver model support to the TSEC driver,
convert ls1021atwr board to use it.
This depends on previous DM series for ls1021atwr:
http://patchwork.ozlabs.org/patch/561855/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[Vladimir] Made the following changes:
- Added 'status = "disabled";' for all Ethernet ports in ls1021a.dtsi
- Fixed the confusion between the SGMII/TBI PCS for enet0 and enet1 -
a mistake ported over from Linux. Each SGMII PCS lies on the private
MDIO bus of the interface (and the RGMII enet2 has no SGMII PCS).
- Added CONFIG_DM_ETH to all ls1021atwr_* defconfigs
- Completely removed non-DM_ETH support from ls1021atwr
- Changed "compatible" string from "fsl,tsec-mdio" to "fsl,etsec2-mdio"
and from "fsl,tsec" to "fsl,etsec2" to match Linux
By convention, the eTSEC MDIO controller nodes are defined in DT at
0x2d24000 and 0x2d50000, but actually U-Boot does not touch the
interrupt portion of the register map (MDIO_IEVENTM, MDIO_IMASKM,
MDIO_EMAPM).
That leaves only the MDIO bus registers (MDIO_MIIMCFG, MDIO_MIIMCOM,
MDIO_MIIMADD, MDIO_MIIMADD, MDIO_MIIMCON, MDIO_MIIMSTAT) which start at
the 0x520 offset.
So shift the DT-defined register map by the offset of MDIO_MIIMCFG when
mapping the MDIO bus registers.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
LS1028A ethernet interfaces work with at least 8 BDs, set number of buffers
to match that.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
A few device-tree fixes
Binman support for extracting files from an image
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl04t50RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYGPwgAlK9Jw/UoLuag8I1rd6nS8U/EYFP4VRrS
ND5Vpe+3WxuMZvrTZyeg1oOkC6UwCJZJMJPFDN2j+VD8LzUYHymTfBykJZLq11Ks
wAieldpK75ZqKcafHP8TI3L5a2fjTj20Rgg9R3IXjy8pPp9sdtqr/GiupaEY3AJf
Y8SQrL7NRZBKxfaRZZAp2MzbzjyUDwmrgntx/xd0Tr/WwZlOf+dojyAdzKP4udfF
9JcEDi4UOyF/9YBzaSfhYO5h38ZdFan+oXpeXDwjWK5w5YV9uheXLChzloF3d9T0
CRPGfFcyl1EowDO1KB3L73HROAURzEJ8gn76IEqHraHm6dqdmU372g==
=9x0F
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-24jul19-take3' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
Minor driver-model fixes and tweaks
A few device-tree fixes
Binman support for extracting files from an image
The uclass_next_device() routine continues a previously started device
iteration. Change the description that is copied from
uclass_first_device().
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
The comments of dev_read_name() wrongly describe "node" as its
parameter.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Starting libvirt v5.3.0 with QEMU 4.0.0 use of PCI is automatic
and thus storage is connected via PCI, which is not visible to
U-Boot out-of-the-box.
Refactor to do "pci enum" followed by "virtio scan" to see PCI
connected storage, and allow bootloader to load kernel and
initramfs images.
Tested with Fedora/RISCV using releases: libvirt 5.4.0 & 5.5.0,
QEMU 4.0.0 and U-Boot 2019.07 RC4.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
The rproc uclass driver can either be built with SPL_REMOTEPROC
or REMOTEPROC, but the function prototypes in remoteproc.h are
defined only when CONFIG_REMOTEPROC is defined. This can cause
build issues in SPL if CONFIG_REMOTEPROC is not selected.
Fix this by replacing the existing precompiler macro usage with
CONFIG_IS_ENABLED.
Fixes: ddf56bc7e3 ("drivers: Introduce a simplified remoteproc framework")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for A/B boot process on AM57xx based boards:
1. Define 'slot_suffix' variable (using 'ab_select' command)
2. Extend 'emmc_android_boot' boot command (add commands for A/B boot
process)
'ab_select' command is used to decide which slot should be used for
booting up. A/B metadata resides in 'misc' partition.
To activate the A/B boot process, the following config options must be
set:
CONFIG_ANDROID_AB=y
CONFIG_CMD_AB_SELECT=y
For successful A/B boot, the corresponding A/B infrastructure must be
involved on Android side [1] (including mounting system as root), and
disk must be partitioned accordingly.
When A/B boot is enabled, there are some known limitations currently
exist (not related to A/B patches, need to be implemented later):
1. The 'Verified Boot' sequence is not supported
2. dev path to system partition (system_a or system_b) is passed via
'bootargs' as 'root=' argument like 'root=/dev/mmcblk1p12', but
further we'll need to rework it with respect to dm-verity
requirements [2]
In case when A/B partitions are not present in system (and A/B boot is
enabled), boot up process will be terminated and next message will be
shown:
"boot_a(b) partition not found"
[1] https://source.android.com/devices/tech/ota/ab
[2] https://source.android.com/devices/tech/ota/ab/ab_implement#kernel
Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Alistair Strachan <astrachan@google.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch determines the A/B-specific bootloader message structure
that is the basis for implementation of recovery and A/B update
functions. A/B metadata is stored in this structure and used to decide
which slot should we use to boot the device. Also some basic functions
for A/B metadata manipulation are implemented (like slot selection).
The patch was extracted from commits [1], [2] with some coding style
fixes.
[1] https://android-review.googlesource.com/c/platform/external/u-boot/+/729878/2
[2] https://android-review.googlesource.com/c/platform/external/u-boot/+/729880/2
Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds part_get_info_by_dev_and_name_or_num() function which
allows us to get partition info from its number or name. Partition of
interest is specified by string like "device_num:partition_number" or
"device_num#partition_name".
The patch was extracted from [1].
[1] https://android-review.googlesource.com/c/platform/external/u-boot/+/729880/2
Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Alistair Strachan <astrachan@google.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
* Implement the EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE event.
* Address errors of type -Werror=address-of-packed-member when building
with GCC9.1
* Fix an error when adding memory add addres 0x00000000.
* Rework some code comments for Sphinx compliance.
-----BEGIN PGP SIGNATURE-----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=aj4j
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-10-rc1-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc1 (2)
* Implement the EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE event.
* Address errors of type -Werror=address-of-packed-member when building
with GCC9.1
* Fix an error when adding memory add addres 0x00000000.
* Rework some code comments for Sphinx compliance.
Backport and squash below Linux v5.2 commits:
Commit id * Summary line
da3e1c57caf93e [1] soc: renesas: r8a77970-sysc: Remove non-existent CR7 power domain
b5eb730e031aca [1] soc: renesas: r8a77970-sysc: Correct names of A2DP/A2CN power domains
3961d355dfb512 dt-bindings: power: r8a77965: Remove non-existent A3IR power domain
(*) Patch id mismatch between Linux and U-Boot commit
[1] Dropped changes in drivers/soc/renesas/r8a77970-sysc.c,
since the file doesn't exist in U-Boot.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
The current implementation supports only binary file load.
Add helpers to support ELF32 format (sanity check, and load).
Note that since an ELF32 image is built for the remote processor, the
load function uses the device_to_virt ops to translate the addresses.
Implement a basic translation for sandbox_testproc.
Add related tests. Test result:
=> ut dm remoteproc_elf
Test: dm_test_remoteproc_elf: remoteproc.c
Test: dm_test_remoteproc_elf: remoteproc.c (flat tree)
Failures: 0
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add the following functions to translate DMA address to CPU address:
- dev_translate_dma_address()
- ofnode_translate_dma_address()
- of_translate_dma_address()
- fdt_translate_dma_address()
These functions work the same way as xxx_translate_address(), with the
difference that the translation relies on the "dma-ranges" property
instead of the "ranges" property.
Add related test. Test report:
=> ut dm fdt_translation
Test: dm_test_fdt_translation: test-fdt.c
Test: dm_test_fdt_translation: test-fdt.c (flat tree)
Failures: 0
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
- rk3399 lpddr4 support
- rk3399-rock960 board support improvement
- Eliminate pyelftools dependency by make_fit_atf.py
- clean up rockchip dts to use -u-boot.dtsi
- use ARM arch/generic timer instead of rk_timer
- clean up Kconfig options for board support
This fixes 3 boards that don't use CONFIG_EXTRA_ENV_SETTINGS from
socfpga_common.h. They need to enable reset manager compatibility
mode unless all peripheral drivers in Linux support reset handling.
Fixes: commit 4b2e32efa4 ("arm: socfpga: gen5: deassert peripheral reset by default")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reported-by: Wolfgang Grandegger <wg@aries-embedded.de>
SPL/TPL share the same secure_timer_init(), update to use
one copy source code and update to use CONFIG_ROCKCHIP_STIMER_BASE
as base address and rename to function name to rockchip_stimer_init().
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We prefer to use ARM arch timer instead of rockchip timer, so that
we are using the same timer for SPL, U-Boot and Kernel, which will
make things simple and easy to track to boot time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We prefer to use ARM arch timer instead of rockchip timer, so that
we are using the same timer for SPL, U-Boot and Kernel, which will
make things simple and easy to track to boot time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We prefer to use ARM arch timer instead of rockchip timer, so that
we are using the same timer for SPL, U-Boot and Kernel, which will
make things simple and easy to track the boot time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We prefer to use ARM arch timer instead of rockchip timer, so that
we are using the same timer for SPL, U-Boot and Kernel, which will
make things simple and easy to track to boot time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Some rk3288 boards are using raw image of u-boot.bin, and now
it's much bigger than default 200KB, update CONFIG_SYS_MONITOR_LEN
to 600KB.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This patch enables DM I2C for DHCOM i.MX6 PDK2 boards and
removes non DM I2C code. The I2C EEPROM with ethaddr (MAC)
is defined in the device tree. Use UCLASS_I2C_EEPROM
to find the device by fixed hardware path and read the ethaddr.
Tested with DHCOM i.MX6dl and DHCOM i.MX6q.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Remove obsolete legacy usbboot wrapper, as distroboot can handle
booting from USB drivers.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Remove obsolete legacy usbboot wrapper, as distroboot can handle
booting from USB drivers.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
1. Introduce androidboot wrapper for booting AOSP.
2. Add partitions_android env var for simplifying the process of
writing new gpt table from U-boot shell/fastboot.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Unfortunately, that missing M makes the current downstream NXP BSP
4.14.98_2.0.0_ga crash early during Linux kernel boot. Fix this.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Use CONFIG_IS_ENABLED(WDT) to permit use of WDT in SPL without DM,
while the full U-Boot can use rich DM/DT WDT driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Suniel Mahesh <sunil.m@techveda.org>
Some comments are not needed anymore after Kconfig automated conversion.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
mccmon6 works in 10/100 MiB Ethernet environment, so disabling 1GiB support
improves robustness of the network after power up (as one don't need to
wait for autoneg).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
If no CONFIG_OPTEE_LOAD_ADDR is provided i.e. you are not loading OPTEE
into memory in u-boot, then just set the non-existent CONFIG option to
zero, elsewise stringify(CONFIG_OPTEE_LOAD_ADDR) will return
"CONFIG_OPTEE_LOAD_ADDR" - which looks weird in the u-boot environment.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
In the Mbed Linux OS bootflow OP-TEE runs before u-boot and provides a DTB
overlay at 0x83100000.
This overlay should subsequently be merged into the main DTB before handing
over to the kernel.
This patch defines fdtovaddr at 0x83100000.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reusing the loadaddr to load the boot script breaks some of the logic we
want to have around the bootscript/FIT load addresses. Making a dedicated
bootscript address allows us to differentiate the bootscript load address
from the Linux Kernel or OPTEE load address, thus ensuring that no matter
what the load sequence the bootscript and Kernel/OPTEE binary load
addresses do not conflict.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
When obtaining the bootscript from a FIT image we need to specify the name
of the bootscript as defined inside of the FIT.
This patch makes a define that appends a "bootscr" parameter to the source
command when compiling up in FIT mode on warp7.
An environment variable is supplied to enable others to use a different
name than "bootscr" as the image name of the boot script in their FIT.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
BD71837 and BD71847 is PMIC intended for powering single-core,
dual-core, and quad-core SoC’s such as NXP-i.MX 8M. BD71847
is used for example on NXP imx8mm EVK.
Add regulator driver for ROHM BD71837 and BD71847 PMICs.
BD71837 contains 8 bucks and 7 LDOS. BD71847 is reduced
version containing 6 bucks and 6 LDOs. Voltages for DVS
bucks (1-4 on BD71837, 1 and 2 on BD71847) can be adjusted
when regulators are enabled. For other bucks and LDOs we may
have over- or undershooting if voltage is adjusted when
regulator is enabled. Thus this is prevented by default.
BD718x7 has a quirk which may leave power output disabled
after reset if enable/disable state was controlled by SW.
Thus the SW control is only allowed for BD71837 bucks
3 and 4 by default. The impact of this limitation must be
evaluated board-by board and restrictions may need to be
modified. (Linux driver get's these limitations from DT and we
may want to implement same on u-Boot driver).
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Writing/updating boot image in nand device is not
straight forward in i.MX6 platform and it requires
boot control block(BCB) to be configured.
It becomes difficult to use uboot 'nand' command to
write BCB since it requires platform specific attributes
need to be taken care of.
It is even difficult to use existing msx-nand.c driver by
incorporating BCB attributes like mxs_dma_desc does
because it requires change in mtd and nand command.
So, cmd_nandbcb implemented in arch/arm/mach-imx
BCB contains two data structures, Firmware Configuration Block(FCB)
and Discovered Bad Block Table(DBBT). FCB has nand timings,
DBBT search area, page address of firmware.
On summary, nandbcb update will
- erase the entire partition
- create BCB by creating 2 FCB/DBBT block followed by
1 FW block based on partition size and erasesize.
- fill FCB/DBBT structures
- write FW/SPL on FW1
- write FCB/DBBT in first 2 blocks
for nand boot, up on reset bootrom look for FCB structure in
first block's if FCB found the nand timings are loaded for
further reads. once FCB read done, DTTB will load and finally
firmware will be loaded which is boot image.
Refer section "NAND Boot" from doc/imx/common/imx6.txt for more usage
information.
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
This patch provides code to implement the CCF clock tree in sandbox. It
uses all the introduced primitives; some generic ones are reused, some
sandbox specific were developed.
In that way (after introducing the real CCF tree in sandbox) the recently
added to clk-uclass.c: clk_get_by_id() and clk_get_parent_rate() are tested
in their natural work environment.
Usage (sandbox_defconfig and sandbox_flattree_defconfig):
./u-boot --fdt arch/sandbox/dts/test.dtb --command "ut dm clk_ccf"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The generic mux clock code for CCF requires reading the clock multiplexer
value from HW registers. As sandbox by design has readl() as no-op it was
necessary to provide this value in the other way.
The new field in the mux structure (accessible only when sandbox is run)
has been introduced for this purpose.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The generic divider clock code for CCF requires reading the divider value
from HW registers. As sandbox by design has readl() as no-op it was
necessary to provide this value in the other way.
The new field in the divider structure (accessible only when sandbox is
run) has been introduced for this purpose.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch brings the files from Linux kernel (linux-stable/linux-5.1.y
SHA1: 5752b50477da)to provide clocks support as it is used on the Linux
kernel with Common Clock Framework [CCF] setup.
The directory structure has been preserved. The ported code only supports
reading information from PLL, MUX, Divider, etc and enabling/disabling
the clocks USDHCx/ECSPIx depending on used bus. Moreover, it is agnostic
to the alias numbering as the information about the clock is read from the
device tree.
One needs to pay attention to the comments indicating necessary for U-Boot's
driver model changes.
If needed, the code can be extended to support the "set" part of the clock
management.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit adds the clk_get_by_id() function, which is responsible
for getting the udevice with matching clk->id. Such approach allows
re-usage of inherit DM list relationship for the same class (UCLASS_CLK).
As a result - we don't need any other external list - it is just enough
to look for UCLASS_CLK related udevices.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This commit adds the clk_get_parent_rate() function, which is responsible
for getting the rate of parent clock.
Unfortunately, u-boot's DM support for getting parent is different
(the parent relationship is in udevice) than the one in Common Clock
Framework [CCF] in Linux.
To alleviate this problem - the clk_get_parent_rate() function has been
introduced to clk-uclass.c.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This commit adds the clk_get_parent() function, which is responsible
for getting the parent's struct clock pointer.
U-Boot's DM support for getting parent is different (the parent
relationship is in udevice) than the one in Common Clock Framework [CCF]
in Linux. To obtain the pointer to struct clk of parent the
pdev->uclass_priv field is read via dev_get_clk_ptr() wrapper.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This commit extends the struct clk to provide information regarding the
flags related to this devices.
Those flags are clk device agnostic and indicate generic features
(like e.g. CLK_GET_RATE_NOCACHE - the need to always recalculate the rate).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This commit extends the struct clk to provide information regarding the
clock rate.
As a result the clock tree traversal is performed at most once, and further
reads are using the cached value.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
There is no UCLASS_CLOCK uclass defined. Instead we do use the UCLASS_CLK.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The location and license header of DT bindings header for SiFive
clock driver has changed in upstream Linux hence this patch.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that SiFive clock driver is merged in upstream Linux, we
sync-up WRPLL library used by SiFive clock driver with upstream
Linux sources.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To match SiFive clock driver with latest Linux, we factor-out PLL
library as separate module under drivers/clk/analogbits.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add printdec, this would help to print an
output a decimalism value.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
The inline functions net_read_u32() and net_copy_u32() have been created to
copy unaligned u32. But this is not obvious to the compiler. GCC 9.1
introduces a check -Werror=address-of-packed-member which leads to a build
error on Travis CI:
net/bootp.c: In function ‘dhcp_send_request_packet’:
net/bootp.c:1011:27: error: taking address of packed member of
‘struct bootp_hdr’ may result in an unaligned pointer value
[-Werror=address-of-packed-member]
1011 | net_copy_u32(&bp->bp_id, &bp_offer->bp_id);
Change the type of the function parameters to void * to avoid the build
error.
Reported-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds a class for MDIO MUXes, which control access to a series of
downstream child MDIOs.
MDIO MUX drivers are required to implement a select function used to switch
between child buses.
MUX children are registered as MDIO buses and they can be used just like
regular MDIOs.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Added a comment on the limitations of phy_find_by_mask API when scanning
MDIO buses with multiple PHYs present. Added short descriptions to the
other APIs in phy.h for consistency.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Various FS/disk related fixes with security implications.
- Proper fix for the pci_ep test.
- Assorted bugfixes
- Some MediaTek updates.
- 'env erase' support.
If U-Boot is loaded and started from TF-A (you need to change
SYS_TEXT_BASE to 0x60000000), it will hang up at flash initialization.
If secure mode is off (default, or -machine virt,secure=off) at qemu,
it will provide dtb with two flash memory banks:
flash@0 {
bank-width = <0x4>;
reg = <0x0 0x0 0x0 0x4000000 0x0 0x4000000 0x0 0x4000000>;
compatible = "cfi-flash";
};
If secure mode is on, on the other hand, qemu provides dtb with 1 bank:
flash@0 {
bank-width = <0x4>;
reg = <0x0 0x4000000 0x0 0x4000000>;
compatible = "cfi-flash";
};
As a result, flash_init()/flash_get_size() will eventually fail.
With this patch applied, relevant CONFIG values are modified.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
this patch adds basic changes for adding a erase-subcommand to env
with this command the environment stored on non-volatile storage written
by saveenv can be cleared.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
squashed fixes
- start message with "Erasing"
- mark erase-function as optional
- env: separate eraseenv from saveenv
Suggested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The block count entry in the EXT4 filesystem disk structures uses
standard 512-bytes units for most of the typical files. The only
exception are HUGE files, which use the filesystem block size, but those
are not supported by uboot's EXT4 implementation anyway. This patch fixes
the EXT4 code to use proper unit count for inode block count. This fixes
errors reported by fsck.ext4 on disks with non-standard (i.e. 4KiB, in
case of new flash drives) PHYSICAL block size after using 'ext4write'
uboot's command.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This will allow for downloading and applying overlays from an MMC/SD
boot media based on the overlay_files ENV variable containing a list
of overlay files.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The TI AM654x EVM base board and the associated daughtercards have on-
board I2C-based EEPROMs containing board configuration data. Use the
board detection infrastructure introduced earlier to do the following:
1) Parse the AM654x EVM base board EEPROM and populate items like board
name and MAC addresses into the TI common EEPROM data structure
residing in SRAM scratch space
2) Check for presence of daughter card(s) by probing the associated
presence signals via an I2C-based GPIO expander. Then, if such a
card is found, parse the data such as additional Ethernet MAC
addresses from its on-board EEPROM and populate into U-Boot
accordingly
3) Dynamically create an U-Boot ENV variable called overlay_files
containing a list of daugherboard-specific DTB overlays based on
daughercards found.
This patch adds support for the AM654x base board ("AM6-COMPROCEVM")
as well as for the IDK ("AM6-IDKAPPEVM"), OLDI LCD ("OLDI-LCD1EVM")
PCIe/USB3.0 ("SER-PCIEUSBEVM"), 2 Lane PCIe/USB2.0 ("SER-PCIE2LEVM"),
and general purpuse ("AM6-GPAPPEVM") daughtercards.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Switch to using the full malloc scheme in post-relocation SPL to allow
better utilization of available memory for example by allowing memory
to get freed. Initially allocate a 16MB-sized region in DDR starting
at address 0x84000000 for this purpose.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
In order to be able to use more advanced driver functionality which often
relies on having BSS initialized during early boot prior to relocation
several things need to be in place:
1) Memory needs to be available for BSS to use. For this, we locate BSS
at the top of the MCU SRAM area, with the stack starting right below
it,
2) We need to move the initialization of BSS prior to entering
board_init_f(). We will do this with a separate commit by turning on
the respective CONFIG option.
In this commit we also clean up the assignment of the initial SP address
as part of the refactoring, taking into account the pre-decrement post-
increment nature in which the SP is used on ARM.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
The current U-Boot SPL image loader infrastructure is very powerful,
able to initialize and load from a variety of boot media however it
is strongly geared towards loading specific types of images in a very
specific way. To address the need being able to use this infrastructure
to load arbitrary image files go ahead and refactor it as follows:
- Refactor existing spl_mmc_load_image function into superset function,
accepting additional arguments such as filenames and media load offset
(same concept can also be applied toother spl_XXX_load_image functions)
- Extend the loader function to "remember" their peripheral initialization
status so that the init is only done once during the boot process,
- Extend the FIT image loading function to allow skipping the parsing/
processing of the FIT contents (so that this can be done separately
in a more customized fashion)
- Populate the SPL_LOAD_IMAGE_METHOD() list with a trampoline function,
invoking the newly refactored superset functions in a way to maintain
compatibility with the existing behavior
This refactoring initially covers MMC/SD card loading (RAW and FS-based).
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add Support for creating a GPT partition for the filesystem in eMMC.
The filesystem is created in the user partition (partition 0).
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The HOST_CONTROL2 register is a part of SDHC v3.00 and not just specific
to arasan/zynq controllers. Add the same to sdhci.h.
Also create a common API to set UHS timings in HOST_CONTROL2.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The am654_sdhci driver needs to switch the clock off
before disabling its phy dll and needs to re-enable
the clock before enabling the phy again.
Therefore, make the sdhci_set_clock() function accessible
in the am654_sdhci driver.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In device nodes with more than one entry in the reg property,
it is sometimes useful to regmap only of the entries. Add an
API regmap_init_mem_index() to facilitate this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In packed structures GUIDs are not aligned. Avoid a build error with
GCC 9.1 by using const void * as argument for guidcmp().
Reported-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We currently have some inconsistent use of efi_add_memory_map()
throughout the code. In particular the return value of efi_add_memory_map()
is not interpreted the same way by various users in the codebase.
This patch does the following:
- Changes efi_add_memory_map() to return efi_status_t.
- Adds a method description to efi_add_memory_map().
- Changes efi_add_memory_map() to return EFI_SUCCESS
- Returns non-zero for error in efi_add_memory_map()
- Updates efi_allocate_pages() to new efi_add_memory_map()
- Updates efi_free_pages() to new efi_add_memory_map()
- Updates efi_carve_out_dt_rsv() to new efi_add_memory_map()
- Updates efi_add_runtime_mmio() to new efi_add_memory_map()
Fixes: 5d00995c36 ("efi_loader: Implement memory allocation and map")
Fixes: 74c16acce3 ("efi_loader: Don't allocate from memory holes")
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Alexander Graf <agraf@csgraf.de>
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We should use predefined constants instead of magic numbers.
Move some constant definitions from include/pe.h to
include/asm-generic/pe.h.
Use these constants in crt0_*_efi.S.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
IMAGE_SUBSYSTEM_EFI_APPLICATION is already defined in
include/asm-generic/pe.h which is included in include/pe.h. We should
not define it twice.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Probably for no particular reason SUNXI_GPIO was still defined the "old
way", in header files only.
Introduce SUNXI_GPIO to the Kconfig file in drivers/gpio to remove
another line from our dreadful config_whitelist.txt.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
stand-alone devices. Useful in particular for systems that support
DM_ETH and have a stand-alone MDIO hardware block shared by multiple
Ethernet interfaces.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- mmc spi driver model support
- drop mmc_spi command
- enhanced Strobe mmc HS400 support
- minor mmc bug/fixes and optimization
- omap hsmmc and mvbeu update
- sdhci card detect support
eMMC 5.1+ supports HS400 Enhances Strobe mode without the need for
tuning procedure.
The flow is as following:
- set HS_TIMIMG (Highspeed)
- Host change freq to <= 52Mhz
- set the bus width to Enhanced strobe and DDR8Bit(CMD6),
EXT_CSD[183] = 0x86 instead of 0x80
- set HS_TIMING to 0x3 (HS400)
- Host change freq to <= 200Mhz
- Host select HS400 enhanced strobe complete
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The mmc_spi command was added to manually setup MMC over SPI bus
using command. This was required by the legacy non-DM MMC_SPI driver.
With DM based MMC_SPI driver in-place, we can now use all general
storge commands and mmc command for MMC over SPI bus hence we remove
the mmc_spi command all it's references.
Suggested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The e-MMC spec allows the e-MMC to specify a timeout for the partition
switch command. It can take up to 2550 ms. There is no lower limit to this
value in the spec, but do as the the linux driver does and force it to be
at least 300ms.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Starting with rev 4.5, the eMMC can define a generic timeout for the
SWITCH command.
Following Linux Kernel code, the timeout also changed from 1000 -> 500
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Using the DAT0 line as a rdy/busy line is an alternative to reading the
status register of the card. It especially useful in situation where the
bus is not in a good shape, like when modes are switched.
This is also how the linux driver behaves.
Note of warning: As per the specification, while polling on DAT0 the CLK
must not turned off: "[...] Without a clock edge the Device (unless
previously disconnected by a deselect command (CMD7)) will force the DAT0
line down, forever. [...]"
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This reverts commit 318a7a576b.
The last and only user of this callback had been the omap_hsmmc driver.
It is not used anymore. Removing the callback.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This patch reads card detect properties from device tree &
added mmc capability macros in mmc.h.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Removed MMC_CAP_NONREMOVABLE, MMC_CAP_NEEDS_POLL macros from
mvebu_mmc.h to avoid redefining of these macros when compiled with
mvebu based configs.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
add gpio-hog support. GPIO hogging is a mechanism
providing automatic GPIO request and configuration
as part of the gpio-controller's driver probe function.
for more infos see:
doc/device-tree-bindings/gpio/gpio.txt
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Michal Simek <michal.simek@xilinx.com> (zcu102)
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This converts LEGO MINDSTORMS EV3 to the driver model. MMC, SERIAL, SPI
and SPI_FLASH are converted.
The device tree contains only the minimal nodes required by U-Boot
since the size of U-Boot is limited to 256K on this device.
Signed-off-by: David Lechner <david@lechnology.com>
This addresses the following warning message:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
As USB support for older OMAP3 SoC's improves, OMAP3 EVM can be
readily adapted. There is some additional 'gpio-hog' support
needed to fully setup USB in a similar manner to Linux.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Add support of Trusted boot chain with OP-TEE
- reserved 32MB at the end of the DDR for OP-TEE
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Change config not directly linked to CONFIG_DISTRO_DEFAULTS.
Allow to deactivate CONFIG_SYS_MTDPARTS_RUNTIME when
CONFIG_MTDPARTS_DEFAULT is defined in defconfig.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Prevent USB enumeration and avoid unnecessary delay in bootcmd_pxe
as Ethernet device is not attached to USB.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
For boot from flash, check presence of default environment to force
save env.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Add "st,package" entry. Possibles values are:
-STM32MP_PKG_AA for LFBGA448 (18*18) package
-STM32MP_PKG_AB for LFBGA354 (16*16) package
-STM32MP_PKG_AC for TFBGA361 (12*12) package
-STM32MP_PKG_AD for TFBGA257 (10*10) package
see Linux commit 966d9b928f626a54a0c27c0fdae1e3dfe9bab416
for v5.2-rc1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl0nbDoRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZcBQgAn+ojgq/hD89bihuhz2oEe6rhzHB9OkcC
sHrVL8Jbmby/BuzISGe4oeeM5yVygBVtUiN/72JiiAHLmykqc4CpRjNvgOOAgKCy
Ml8UyiBNNVNfrD6f9PxAKvPZf6S0gfLnomGOQ/psdEojpY5AvQxQ36D+QFZ0AMP5
67/xjSfN9bNPw8UbgE/VhJ+WFbU948BP2EBt6+NBAtv7HW4AX9vT0famJfWEjwq8
ftmcFOSNGgYcDQ5BwQWX1sFhnwb9XSfurlQsVYBsFA4cx4gj0DfUm1Ugr4wDD+lo
91P+76hSBQ+mHp1HJ90WMd2vAaElG7/SoaicXo9pW6Rc7WIgTjk7gg==
=SdZy
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-9jul19-take2' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
- Sandbox improvements including .dts refactor
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
- SPL SATA enhancements to allow booting from RAW SATA device
needed for Clearfog (Baruch)
- Enable SATA booting on Clearfog (Baruch)
- Misc changes to Turris Omnia (Marek)
- Enable CMD_BOOTZ and increase SYS_BOOTM_LEN on crs305-1g-4s
(Luka)
- Enable FIT support for db-xc3-24g4xg (Chris)
- Enable DM_SPI on Keymile Kirkwood board with necessary changes
for this (Pascal)
- Set 38x and 39x AVS on lower frequency (Baruch)
- import DT updates from Linux
- add UniPhier SPI controller driver
- make U-Boot image for 64bit SoCs position independent
- tidy up various init code for next generation SoCs
- misc cleanups
-----BEGIN PGP SIGNATURE-----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=X9wS
-----END PGP SIGNATURE-----
Merge tag 'uniphier-v2019.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier
UniPhier SoC updates for v2019.10
- import DT updates from Linux
- add UniPhier SPI controller driver
- make U-Boot image for 64bit SoCs position independent
- tidy up various init code for next generation SoCs
- misc cleanups
Perform the following updates:
- Relocate the commit id from the file to the description of U-Boot
commit. The AOSP commit is c784ce50e8c10eaf70e1f97e24e8324aef45faf5.
This is done to avoid stale references in the file itself. The
reasoning is in https://patchwork.ozlabs.org/patch/1098056/#2170209.
- Minimize the diff to AOSP, to decrease the effort of the next AOSP
backports. The background can be found in:
https://patchwork.ozlabs.org/patch/1080394/#2168454.
- Guard the static_assert() calls by #ifndef __UBOOT__ ... #endif,
to avoid compilation failures of files including the header.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The name CONFIG_LEGACY_IMAGE_FORMAT reads slightly better along with
allowing us to avoid a rather nasty Kbuild/Kconfig issue down the line
with CONFIG_IS_ENABLED(IMAGE_FORMAT_LEGACY). In a few places outside of
cmd/ switch to using CONFIG_IS_ENABLED() to test what is set.
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce new UCLASS_PCI_EP class for handling PCI endpoint
devices, allowing to set various attributes of the PCI endpoint
device, such as:
* configuration space header
* BAR definitions
* outband memory mapping
* start/stop PCI link
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
KM Kirkwood boards now implement the driver model for its SPI flash
interface. Therefore, the old board specific claim and release functions
can be deleted. The preprocessor definition CONFIG_SYS_KW_SPI_MPP is yet
unused as well. All its appearances and dependencies are removed in the
kirkwood_spi driver, header files and finally the configuration whitelist.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This change enables CMD_BOOTZ and increases SYS_BOOTM_LEN to
make it easier to work with kernel images.
Signed-off-by: Luka Kovacic <me@lukakovacic.xyz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
If SCSI and USB boot options are both available, try to boot from SCSI
first.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This is not needed here since Omnia is using DM_PCI now.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The U-Boot partition is 1 MiB and environment is 64 KiB. It does not
make sense to have environment at 0xc0000 when it could be at 0xf0000
and we can have more space for U-Boot binary.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Set default value for the ethact variable to the WAN port.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
See the offset of U-Boot in raw SATA disk to the same value as the MMC
offset. That is 0x140 sectors from the beginning of the SPL, which is
0x141 sectors from the beginning of the device (after the MBR sector).
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
There is no good reason to limit the trace buffer to 2GiB on a 64bit
system. Adjust the types of the relevant parameters.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds dm_pci_flr API that issues a Function Level reset on a PCI-e function,
if FLR is supported.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Makes dm_pci_map_bar API available for integrated PCI devices that
support Enhanced Allocation instead of the original PCI BAR mechanism.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The comment now indicates that the input argument bar is a register offset,
not a BAR index.
It also mentions which BARs are supported for type 0/1 and that the
function can return 0 on error.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add documentation for the pre-reloc property in SPL and TPL device-tree:
- u-boot,dm-pre-proper
- u-boot,dm-pre-reloc
- u-boot,dm-spl
- u-boot,dm-tpl
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The base of DRAM will be changed for the next generation SoC.
The addresses needed for booting the kernel should be shifted
according to the DRAM base.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The base of DRAM will be changed for the next generation SoC.
To support it along with existing SoCs in the single defconfig,
set 'loadaddr' at boot-time by adding the offset to the DRAM base.
CONFIG_SYS_LOAD_ADDR is still hard-coded for compilation, but the
value from environment variable 'loadaddr' should be used.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The base address of DRAM was 0x80000000 for all the ARM SoCs of this
family in the past. It will be changed to 0x20000000 for a planned new
SoC. To support multiple SoCs by the single uniphier_v8_defconfig, the
base must be run-time determined.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is a remnant of commit f89d6133ee ("configs: move
CONFIG_SPL_TEXT_BASE to Kconfig").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdJEZEAAoJEB6zHgIOrC/I+LAH/jUDQpF5I68h0ZFGm3xoyGhm
3CSv8viOm/kL+GLubjnv4cwAp8N8VRpeJekz0Jt1Xp8C6OIgtnJ2Fln72KD+Z0IC
Rq7ByRS16iq4b6IUDRZObE4Jzxmf7rXU3jr0+/vd/en7kxVlvA9+Gsffs3OTGxC7
z9PysRZPBMH/smIPXdEQxYifnbpDG4fmfGcUWKrYfkB0Kq6Ep98Ia/gXNCY8XJ/A
sbNQGjJWJZWXS/TDetcC2VikssJ+yNFF34uzV+HD5Y3DW6ywLhuoDOz1pg8RR36i
YjcTCQz8lL/UVaUzrGUgPVAC3gdKY6J26GtV3vZavxBcmtGf0FhVtXO/tZc9AsY=
=6G45
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.10-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features and fixes for 2019.10 cycle
This includes the Atmel QSPI driver and support for the at91 boards.
This is the port of the driver from Linux, mostly done by Tudor Ambarus.
The spi-nor flash resides on spi bus 1. Update the CONFIG_ENV_SPI_CS
and CONFIG_BOOTCOMMAND accordingly.
Based on original work by Wenyou Yang.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[tudor.ambarus@microchip.com: amend the commit message.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Use the qspi memory layout defined in at91-sama5_common - it aligns
with the 8 Mbyte flash (sst26vf064b-104i/sn) available in sama5d27_som1_ek.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Use the same memory layout as we use for the NAND boot on the other boards.
QSPI flashes are present on the following boards:
sama5d2_xplained RevB: 32 Mbyte flash (mx25l3273fm2i-08g)
sama5d2_xplained RevC: 8 Mbyte flash (sst26vf064b-104i/sn)
sama5d27_som1_ek: 8 Mbyte flash (sst26vf064b-104i/sn)
sama5d2_ptc_ek: 8 Mbyte flash (sst26vf064b-104i/sn)
The 8 Mbyte limit is enough to cope with the memory layout used in the NAND
boot. rootfs exceeds the 8 Mbyte limit and will stay in eMMC in the
sama5d2_xplained case. The final scope is to use a single memory layout for
all boot medias.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
[tudor.ambarus@microchip.com: change memory layout, add commit message]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The motivation is to use the UBI atomic volume rename functionality to
allow double copy software updates on UBI. To that end the SPL is
configured to always load the same volume name (e.g. "u-boot"),
whereas a software updater always installs into the secondary volume
"u-boot_r". After successful installation, these two volume names are
switched.
This extension is protected by #ifdefs as it will somewhat slow down
loading of volumes by id. This is because the code needs to disable
the optimization of ignoring all volume ids which are not
to-be-loaded, since these can only be resolved after attaching.
This adds two vtbl related functions from Linux, which are taken from
the same kernel version as the current main U-Boot UBI code (Linux 4.2
64291f7db5bd8).
Signed-off-by: Hamish Guthrie <hamish.guthrie@kistler.com>
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
Migrate the ubispl configuration for the omap3_igep00x0 and
am335x_igep003x boards to KConfig. Both boards were built with
SOURCE_DATE_EPOCH=0 and found to be equal before and after.
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Javier Martínez Canillas <javier@dowhile0.org>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Enable the extended ENV options for AT91 and OMAP2PLUS in order to be
able to use CONFIG_ENV_UBI_* on these architectures.
As this change also makes the configs ENV_SIZE, ENV_SECT_SIZE,
ENV_OFFSET visible to AT91 and OMAP2PLUS, migrate users of these to
KConfig.
This migration was run using an extended moveconfig.py which evaluates
expressions such as "(512 << 10)". See patch ("moveconfig: expand
simple expressions").
All modified boards were built with SOURCE_DATE_EPOCH=0 before and
after the change and successfully confirmed that the identical binary
is generated (the only exception was igep00x0, which does not define
CONFIG_ENV_IS_IN_UBI in the original board header. Once that is
defined, the test passes too).
hs: rebased patch to:
68b90e57bc: "configs: tinker-rk3288 disable CONFIG_SPL_I2C_SUPPORT"
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Tom Rini <trini@konsulko.com>
Introduce the KConfig option CONFIG_ENV_UBI_VOLUME_REDUND for defining
the name of the UBI volume used to store the redundant environment.
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
hs: get rid of stm32mp1* build errors
Fix a possible overflow for GUID partition tables.
For some runtime services we only have implementations valid at boottime.
So we replace them when leaving boottime. Move this from
SetVirtualAddressMap() to ExitBootServices() as SetVirtualAddressMap() is
not called by all operating systems. Adjust the Python tests accordingly.
Bump the supported UEFI specification version to 2.8.
-----BEGIN PGP SIGNATURE-----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=wHU6
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-10-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc1
Fix a possible overflow for GUID partition tables.
For some runtime services we only have implementations valid at boottime.
So we replace them when leaving boottime. Move this from
SetVirtualAddressMap() to ExitBootServices() as SetVirtualAddressMap() is
not called by all operating systems. Adjust the Python tests accordingly.
Bump the supported UEFI specification version to 2.8.
One of the SD-CARD slots on the Wandboard Quad B1 is MMC 2. Enable it as a
boot device.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Linux can be called with a command line parameter efi=novamap, cf.
commit 4e46c2a95621 ("efi/arm/arm64: Allow SetVirtualAddressMap() to be
omitted"). In this case SetVirtualAddressMap() is not called after
ExitBootServices().
OpenBSD 32bit does not call SetVirtualAddressMap() either.
Runtime services must be set to an implementation supported at runtime
in ExitBootServices().
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Suggested-by: Alexander Graf <agraf@csgraf.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We are implementing UEFI variable RuntimeServicesSupported and set the
unimplemented runtime functions return EFI_UNSUPPORTED as described in UEFI
specification 2.8. So let's also advertise this specification version in
our system table.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Alexander Graf <agraf@csgraf.de>
Our variable services are only provided at boottime. Therefore when
leaving boottime the variable function are replaced by dummy functions
returning EFI_UNSUPPORTED. Move this patching of the runtime table to the
variable services implementation. Executed it in ExitBootServices().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Let's keep similar things together.
Move efi_query_variable_info() to lib/efi_loader/efi_variable.c
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
