Commit graph

13652 commits

Author SHA1 Message Date
Simon Glass
dcd7c906d0 mscc: Drop dm.h header file
This header file should not be included in other header files. Remove it
from each one and use a forward declaration instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-08-03 22:19:54 -04:00
Simon Glass
dece7747e9 liebherr: Drop duplicate dm.h inclusion
We only need to include this header once. Drop the duplicate.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-08-03 22:19:54 -04:00
Simon Glass
411e9eb88c w1: Drop dm.h header file
This header file should not be included in other header files. Remove it
and use a forward declaration instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-08-03 22:19:54 -04:00
Simon Glass
a00867b47a sf: Drop dm.h header file from spi_flash.h
This header file should not be included in other header files. Remove it
and use a forward declaration instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-08-03 22:19:54 -04:00
Niel Fourie
a1c6aed1de arm: imx6q: pcm058: Rework SPI NOR configuration
Enable CONFIG_SPL_DM_SPI_FLASH to be able to boot from SPI NOR,
modify the offset of U-boot proper in the SPI NOR, so the
difference in offset matches between SPL and U-boot matches that of
the SD Card, allowing u-boot-with-spl.imx to also be copied to SPI
NOR at an offset of 0x400. Update the README to reflect this
change.

Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2020-08-03 17:03:57 +02:00
Parthiban Nallathambi
10e959a1ca imx: Add MYiR Tech MYS-6ULX support
MYS-6ULX is single board computer (SBC) comes with eMMC or NAND based
on imx6ULL SoC from NXP and provision for expansion board. This
commit adds support only for SBC with NAND.

CPU:   Freescale i.MX6ULL rev1.1 528 MHz (running at 396 MHz)
CPU:   Commercial temperature grade (0C to 95C) at 45C
Reset cause: WDOG
Model: MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND
Board: MYiR MYS-6ULX 6ULL Single Board Computer
DRAM:  256 MiB
NAND:  256 MiB
MMC:   FSL_SDHC: 0
In:    serial@2020000
Out:   serial@2020000
Err:   serial@2020000
Net:   FEC0

Working:
 - Eth0
 - MMC/SD
 - NAND
 - UART 1
 - USB host

Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
2020-08-03 17:03:57 +02:00
Patrick Delaunay
4df087ccf9 configs: sandbox: activate env in ext4 support
Activate ENV in EXT4 support in sandbox.

The sandbox behavior don't change; the default environment with
the nowhere backend (CONFIG_ENV_IS_NOWHERE)is still used:
the weak function env_get_location() return ENVL_NOWHERE for priority 0.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-07-31 10:13:00 -04:00
Tom Rini
719f42190d Use binman instead of one of the Rockchip build scripts
Refactor to allow any arch to create SPI-flash images
 New button uclass
 -----BEGIN PGP SIGNATURE-----
 
 iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8g33sRHHNqZ0BjaHJv
 bWl1bS5vcmcACgkQfxc6PpAIreaeEgf/QhmJjd6lEE3ABncRa3texyqq7j9eu+9P
 2JMCahrIzps83LLOkzNSGs1+m1hRuTcdnYNV8FxdmkAjDTYwV5RHOfwtpAr2nkH2
 HBbJRA2qMPleqT8wcymouhaCIRTTCGfUkFgZ+OowwSlHnQ4d2oGU/59Z+AkbpfX0
 3svA1Mlr5rUTZ3qTvdsepuZckuYOTGYZ5jgjbgr+G8F4iW4Ov+OkBxqDz9zFCveF
 md5CHKP1SV+bq67Q9uqUEwatLzYpy1p24j1Qe4G08U1+XCi6r+95VEc7TWxggboj
 eV/5d/sZbGESAtJiJ4TmqpGVcOLzBLI0FOunky0JNFwdcyRS/6KcCg==
 =Xjil
 -----END PGP SIGNATURE-----

Merge tag 'dm-pull-28jul20' of git://git.denx.de/u-boot-dm

Use binman instead of one of the Rockchip build scripts
Refactor to allow any arch to create SPI-flash images
New button uclass
2020-07-29 21:16:08 -04:00
Tom Rini
7cb2060b4e Merge https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- fix SPL boot issue due to early dbgmcu_init() call
- fix SPL boot issue due to dcache memory region configuration
- add support of CONFIG_ENV_IS_IN_MMC
- add specific SD/eMMC partition for U-Boot enviromnent
- enable env in SPL
- use "env info -q" to remove log during boot
- remove env location override for dh_stm32mp1
- update management of misc_read
- check result of find_mmc_device in stm32prog
- use regulator_set_enable_if_allowed for disabling vdd supply in usbphyc
- enable CMD_ADTIMG flag to handle Android images
- device tree alignment with Linux Kernel v5.8-rc1
- remove hnp-srp-disable for usbotg on dk1
- add reset support to uart nodes on stm32mp15x
- use correct weak function name spl_board_prepare_for_linux
- use cd-gpios for ST and DHSOM boards
- add seeed studio odyssey-stm32mp157c board support
- move ethernet PHY into SoM DT
- add DHSOM based DRC02 board support
2020-07-29 16:30:45 -04:00
Pramod Kumar
2a4326ab25 board: ns3: add development keys used in FIT
Add development keys used in FIT.

Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-29 10:37:11 -04:00
Pramod Kumar
e14563db05 board: ns3: add FIT image its file
Add FIT image its file.

Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-29 10:37:11 -04:00
Bharat Kumar Reddy Gooty
53a3e8d469 board: ns3: limit U-boot relocation within 16MB memory
By default relocation happens to a higher address of DDR,
i.e, DDR start + DDR size.

U-Boot shall be used to collect the ramdump.
Restrict U-Boot to use only the 16MB memory, so that this
memory can be reserved. Limit relocation to happen within
16MB memory, start 0xFF00_0000 and end 0x1_0000_0000

Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-29 10:37:11 -04:00
Rayagonda Kokatanur
c8b98482d8 board: ns3: define ddr memory layout
Add both DRAM banks memory information and
the corresponding MMU page table mappings.

Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-29 10:37:11 -04:00
Rayagonda Kokatanur
f01a4e8cc9 board: ns3: program GIC LPI tables
U-boot programs the GIC LPI configuration tables and enables
the LPI table.

Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-29 10:37:10 -04:00
Rayagonda Kokatanur
b5a152e7ca board: ns3: default reset type to L3
Default "reset" from U-Boot to L3 reset.
"reset" command with argument will trigger L1 reset.

Signed-off-by: Rajesh Ravi <rajesh.ravi@broadcom.com>
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-29 10:13:41 -04:00
Abhishek Shah
ef7192e404 board: ns3: add api to save boot parameters passed from BL31
Add API to save boot parameters passed from BL31

Use assembly implementation of save_boot_params instead of c function.
Because generally ATF does not set up SP_EL2 on exiting.
Thus, usage of a C function immediately after exiting with no stack
setup done by ATF explicitly, may cause SP_EL2 to be not sane,
which in turn causes a crash if this boot was not lucky to get
an SP_EL2 in valid range. Replace C implementation with assembly one
which does not use stack this early, and let u-boot to set up its stack
later.

Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Signed-off-by: Rajesh Ravi <rajesh.ravi@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-29 10:13:41 -04:00
Rayagonda Kokatanur
291635aecf board: ns3: add support for Broadcom Northstar 3
Add support for Broadcom Northstar 3 SoC.
NS3 is a octo-core 64-bit ARMv8 Cortex-A72 processors
targeting a broad range of networking applications.

Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-29 10:13:40 -04:00
David Woodhouse
3fad1ca28d board: mediatek: Add support for UniElec U7623 board
This is an MT7623A-based board, very similar to the Banana Pi R2.

http://www.unielecinc.com/q/news/cn/p/product/detail.html?qd_guid=OjXwKCaRlN

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-29 08:43:40 -04:00
David Woodhouse
e3cc511eef board: mediatek: fix mmc_get_boot_dev() for platforms without external SD
On the UniElec U7623 board there is no external SD slot and the preloader
doesn't fill in the magic field at 0x81dffff0 to indicate that it was
booted from eMMC.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-29 08:43:40 -04:00
Stefan Bosch
d1611086e0 arm: add support for SoC s5p4418 (cpu) / nanopi2 board
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- SPL not supported yet --> no spl-dir in arch/arm/cpu/armv7/s5p4418/.
  Appropriate line in Makefile removed.
- cpu.c: '#include <cpu_func.h>' added.
- arch/arm/cpu/armv7/s5p4418/u-boot.lds removed, is not required
  anylonger.
- "obj-$(CONFIG_ARCH_NEXELL) += s5p-common/" added to
  arch/arm/cpu/armv7/Makefile since s5p-common/pwm.c is used instead
  of drivers/pwm/pwm-nexell.c.
- s5p4418.dtsi: '#include "../../../include/generated/autoconf.h"'
  removed, is not necessary, error at out-of-tree building.
  '#ifdef CONFIG_CPU_NXP4330'-blocks (2x) removed. Some minor changes
  regarding mmc. 'u-boot,dm-pre-reloc' added to dp0 because of added
  DM_VIDEO support.
- board/s5p4418/ renamed to board/friendlyarm/
- All s5p4418-boards except nanopi2 removed because there is no
  possibility to test the other boards.
- Kconfig: Changes to have a structure like mach-bcm283x (RaspberryPi),
  e.g. "config ..." entries moved from/to other Kconfig.
- "CONFIG_" removed from several s5p4418/nanopi2 specific defines
  because the appropriate values do not need to be configurable.
- nanopi2/board.c: All getenv(), getenv_ulong(), setenv() and saveenv()
  renamed to env_get(), env_get_ulong(), env_set() and env_save(),
  respectively. MACH_TYPE_S5P4418 is not defined anymore, therefore
  appropriate code removed (not necessary for DT-kernels).
- nanopi2/onewire.c: All crc8() renamed to crc8_ow() because crc8() is
  already defined in lib/crc8.c (with different parameters).
- dts: "nexell,s5pxx18-i2c" used instead of "i2c-gpio", i2c0 and
  i2c1 added. gmac-, ehci- and dwc2otg-entries removed because the
  appropriate functionality is not supported yet. New mmc-property
  "mmcboost" added.
  s5p4418-pinctrl.dtsi: gmac-entries removed, mmc- and i2c-entries
  added.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
  possible (and similar).

Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
2020-07-29 08:43:40 -04:00
Ard Biesheuvel
2e2c2a5e72 arm: qemu: override flash accessors to use virtualizable instructions
Some instructions in the ARM ISA have multiple output registers, such
as ldrd/ldp (load pair), where two registers are loaded from memory,
but also ldr with indexing, where the memory base register is incremented
as well when the value is loaded to the destination register.

MMIO emulation under KVM is based on using the architecturally defined
syndrome information that is provided when an exception is taken to the
hypervisor. This syndrome information describes whether the instruction
that triggered the exception is a load or a store, what the faulting
address was, and which register was the destination register.

This syndrome information can only describe one destination register, and
when the trapping instruction is one with multiple outputs, KVM throws an
error like

  kvm [615929]: Data abort outside memslots with no valid syndrome info

on the host and kills the QEMU process with the following error:

  U-Boot 2020.07-rc3-00208-g88bd5b179360-dirty (Jun 06 2020 - 11:59:22 +0200)

  DRAM:  1 GiB
  Flash: error: kvm run failed Function not implemented
  R00=00000001 R01=00000040 R02=7ee0ce20 R03=00000000
  R04=7ffd9eec R05=00000004 R06=7ffda3f8 R07=00000055
  R08=7ffd9eec R09=7ef0ded0 R10=7ee0ce20 R11=00000000
  R12=00000004 R13=7ee0cdf8 R14=00000000 R15=7ff72d08
  PSR=200001d3 --C- A svc32
  QEMU: Terminated

This means that, in order to run U-Boot in QEMU under KVM, we need to
avoid such instructions when accessing emulated devices. For the flash
in particular, which is a hybrid between a ROM (backed by a read-only
KVM memslot) when in array mode, and an emulated MMIO device (when in
write mode), we need to take care to only use instructions that KVM can
deal with when they trap.

So override the flash read accessors that are used when running on QEMU
under KVM. Note that the the 64-bit wide read and write accessors have
been omitted: they are never used when running under QEMU given that it
does not emulate CFI flash that supports it.

Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2020-07-29 08:43:40 -04:00
Ard Biesheuvel
3fa914af82 arm: qemu: implement enable_caches()
Add an override for enable_caches to enable the I and D caches, along
with the cached 1:1 mapping of all of DRAM. This is needed for running
U-Boot under virtualization with QEMU/kvm.

Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2020-07-29 08:43:40 -04:00
Simon Glass
e6385c7e9c Makefile: Rename ALL-y to INPUTS-y
When binman is in use, most of the targets built by the Makefile are
inputs to binman. We then need a final rule to run binman to produce the
final outputs.

Rename the variable to indicate this, and add a new 'inputs' target.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-07-28 19:30:39 -06:00
Patrick Delaunay
4b64265bb4 board: update test on misc_read result in board_late_init
Update management of misc_read, which now return length of data
after the commit 8729b1ae2c ("misc: Update read() and write()
methods to return bytes xfered")

Fixes: 8b8b3d6b55 ("stm32mp1: board: add environment variable for board id and board rev")

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-07-28 17:39:35 +02:00
Jakob Riepler
1e3d060501 board: dh_stm32mp1: remove env location override
Overriding the environment location is not necessary as the defconfig
for the relevant boards only enable SPI flash and nowhere sources which
are in the same order per default but having this explicit override
prevents using eMMC or SD card (or EXT4) as environment source.

Signed-off-by: Jakob Riepler <jakob.riepler@aviloo.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-07-28 17:36:27 +02:00
Patrick Delaunay
b0cbafe509 configs:stm32mp1: activate env config in SPL
Activate env config in SPL with CONFIG_SPL_ENV_SUPPORT
and use CONFIG_IS_ENABLED macro to test the activated
CONFIG_$(SPL_)ENV_IS_IN_... in env_get_location.

Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-07-28 17:21:37 +02:00
Patrick Delaunay
a9addcafd1 stm32mp1: board: add support of CONFIG_ENV_IS_IN_MMC
Add support of CONFIG_ENV_IS_IN_MMC in env_get_location, used for
all mmc device (SD card and eMMC).
The 2 configs CONFIG_ENV_IS_IN_MMC and CONFIG_ENV_IS_IN_EXT4 are
incompatible.

Add the weak function mmc_get_env_dev to select the mmc boot instance.

Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-07-28 17:21:37 +02:00
Tom Rini
8d1fc6fb89 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
  cleanups
- fsl-crypto: RNG support and bug fixes
2020-07-27 15:18:15 -04:00
Tom Rini
4e05c167a7 binman support for FIT
new UCLASS_SOC
 patman switch 'test' command
 minor fdt fixes
 patman usability improvements
 -----BEGIN PGP SIGNATURE-----
 
 iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8eNVURHHNqZ0BjaHJv
 bWl1bS5vcmcACgkQfxc6PpAIrebA7Qf/QVH9a07SAXXHjIXN7lVkxtf27hevxS80
 +4imgF52UrQHvdMHxw0m7Kmlt6znP6ThziVRMjCQomYILFiKkLrXJcMtqPoN72oI
 XxYnHShMI0Gjoss0rmP0yDNFkUN6Z09Q6wWoHwQG23Hu1kA6E8uw9gZf6dFwFzSB
 7+ER6Omwl2ziyRI137BQnKXmfkJMXB9+mZPZchZYKJF9HeQPFMXhKO6Rte1Qh7Ei
 oEJBKLghpjFZpu9nNkxXiDzFcm/UromG699U45Vgm11p1gp2m2HtOi+6zAtM2IXP
 IQUkG9zfp8sKonmEdNURP9LzjMazH7As9yGrNMn/G/AWVSg7SLmAKg==
 =V8Rw
 -----END PGP SIGNATURE-----

Merge tag 'dm-pull-20jul20-take2a' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm

binman support for FIT
new UCLASS_SOC
patman switch 'test' command
minor fdt fixes
patman usability improvements
2020-07-27 11:15:37 -04:00
Igor Opaniuk
195011b24d colibri-imx7: fix splash logo drawing
1. Configure white on black for video console.
2. Enable printing bmp logo during late board init stage.
3. Use iomux configuration from device tree.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27 14:01:32 +02:00
Igor Opaniuk
391c712dde colibri-imx6ull: show boot logo
1. Show boot logo embed in U-Boot blob.
2. Drop iomux configration for LCD, and use the one provided in device
tree.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27 14:01:32 +02:00
Igor Opaniuk
a5de86c1db ARM: dts: imx7-colibri: multiple node updates
1. Move u-boot specific nodes to u-boot dts include: legacy lcdif
node and aliases.
2. Add iomux configuration for LCD.
3. Drop un-needed u-boot,dm-pre-reloc for alias node.
4. Fix display-timings, use the one from Toradex downstream kernel [1]

[1]: https://git.toradex.com/cgit/linux-toradex.git/tree/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi?h=toradex_4.9-2.3.x-imx#n206
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27 14:01:32 +02:00
Igor Opaniuk
d324189772 toradex: common: show boot logo
Add function for showing boot logo, embed into u-boot blob.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27 14:01:32 +02:00
Igor Opaniuk
306ecc8431 verdin-imx8mm: add EEPROM support for carrier board
Enable these Kconfig symbols:
TDX_CFG_BLOCK_EXTRA=y
TDX_HAVE_EEPROM_EXTRA=y

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27 14:00:36 +02:00
Igor Opaniuk
717fa2c819 toradex: tdx-cfg-block: add carrier board info printing
Add carrier board info printing during boot time:

U-Boot 2020.07-rc4-02435-g1756e05 (Jun 22 2020 - 22:43:59 +0300)

CPU:   Freescale i.MX8MMQ rev1.0 at 1200 MHz
....
Carrier: Toradex Verdin Development Board V1.0A, Serial# 10622780
Verdin iMX8MM #

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27 14:00:36 +02:00
Igor Opaniuk
db4ab6d453 toradex: tdx-cfg-clock: add migration routine from PID8
Add migration routine from PID8 pre-stored values on EEPROM
(including sane value checks).

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27 14:00:36 +02:00
Igor Opaniuk
0c6b5588ef toradex: tdx-cfg-block: add support for EEPROM
This introduces support for EEPROM as a storage for the main Toradex
config block and additional config blocks on extra EEPROM chips (on
carrier board or video adapters).

To enable EEPROM as a storage for the main config block:
TDX_HAVE_EEPROM=y.

For additional EEPROMs please enable this Kconfig symbol:
TDX_CFG_BLOCK_EXTRA=y.

Information about existing EEPROM chips is provided via Device Tree
using aliases.

You can also write configuration for the carrier board using
create_carrier subcommand for cfgblock. Example:

Verdin iMX8MM # cfgblock create_carrier
Supported carrier boards:
UNKNOWN CARRIER                     = [0]
Verdin Carrier Board                = [1]
Choose your carrier board (provide ID): 1
Enter carrier board version (e.g. V1.1B): V1.0A
Enter carrier board serial number: 10622780

Also with barcode:
Verdin iMX8MM # cfgblock create carrier -y 0156100010622780

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27 14:00:36 +02:00
Igor Opaniuk
26921f5853 toradex: tdx-cfg-block: add carrier boards and display adapters
Add defines for supported carrier boards and display adapters.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27 14:00:36 +02:00
Igor Opaniuk
c2e969378d toradex: tdx-cfg-block: add EEPROM read/store wrappers
These functions wrap functionality for storing config blocks in EEPROM.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27 14:00:36 +02:00
Manish Tomar
11504cf584 configs:ls1046afrwy: Add tfa secure boot defonfig
Add TFA secure boot defconfig and Enables secure boot related
configs in it.

Signed-off-by: Manish Tomar <manish.tomar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27 14:23:57 +05:30
Biwen Li
3bb30b9c76 freescale: ls1043aqds: drop ifdef CONFIG_SYS_I2C
- Drop ifdef CONFIG_SYS_I2C to initialize
  baudrate of i2c

- Drop warning of i2c_early_init_f as follows,
  warning: implicit declaration of function 'i2c_early_init_f'; did you
  mean 'arch_early_init_r'? [-Wimplicit-function-declaration]

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27 14:16:29 +05:30
Biwen Li
1b2bdd0605 freescale: ls1043aqds: enable secure system counter
Enable secure system counter in board_early_init_f for udelay()
to fix a bug that always return 0 by timer_read_counter()
when boot from qspi(No TFA)

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27 14:16:29 +05:30
Biwen Li
51d893cd3d freescale: ls1046aqds: drop ifdef CONFIG_SYS_I2C
- Drop ifdef CONFIG_SYS_I2C to initialize
  baudrate of i2c

- Drop warning of i2c_early_init_f as follows,
  warning: implicit declaration of function 'i2c_early_init_f'; did you
  mean 'arch_early_init_r'? [-Wimplicit-function-declaration]

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27 14:16:29 +05:30
Biwen Li
e70e10bc49 freescale: ls1046aqds: enable secure system counter
Enable secure system counter in board_early_init_f for udelay()
to fix a bug that always return 0 by timer_read_counter()
when boot from qspi(No TFA)

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27 14:16:29 +05:30
Yangbo Lu
e1a31034a6 board: fsl: lx2160aqds: identify SDHC adapter during board init
Add support for SDHC adapter identification and configuration
during board init.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27 14:16:28 +05:30
Yangbo Lu
39913acedd Move eSDHC adapter card identification to board files
The eSDHC adapter card identification and multiplexing configuration
through FPGA had been implemented in both common mmc driver and
fsl_esdhc driver. However it is proper to move these code to board
files and do it during board initialization. The FPGA registers are
also board specific.

This patch is to move eSDHC adapter card identification and
multiplexing configuration from mmc driver to specific board files.
And the option CONFIG_FSL_ESDHC_ADAPTER_IDENT is no longer needed.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[Rebased, Removed T1040QDS change as board does not exist]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27 14:16:28 +05:30
Yuantian Tang
c8f8830e0b armv8: ls1028ardb: add xspi parameter to qixis command
Add xspi boot source to qixis command to let the soc boot from
flex-nor flash chip.

Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27 14:16:28 +05:30
Chaitanya Sakinam
cb1de6067a armv8: ls1012a: RGMII ports require internal delay
The correct setting for the RGMII ports on LS1012ARDB is to
enable delay on both Rx and Tx so the interface mode used should
be PHY_INTERFACE_MODE_RGMII_ID

Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27 14:16:28 +05:30
Michal Simek
988341d84a ARM: rmobile: Switch back to fdtdec_setup_memory/banksize_fdt()
The commit 361377dbdb ("ARM: rmobile: Merge prior-stage firmware DT
fragment into U-Boot DT on Gen3") reverted changes introduced by commit
175f502734 ("ARM: renesas: Configure DRAM size from ATF DT fragment")
that's why there is no reason to use functions with _fdt() suffix because
parameter is gd->fdt_blob as is already for functions without _fdt()
suffix.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-25 14:46:57 -06:00
Adam Ford
59028798ab ARM: rmobile: Add Beacon EmbeddedWorks RZG2M Dev Kit
The Beacon EmbeddedWorks kit is based on the R8A774A1 SoC also
known as the RZ/G2M.

The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi.

Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-25 14:19:26 +02:00
Tom Rini
ada61f1ee2 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-riscv
- Fix SiFive HiFive Unleashed board booting failure problem.
- Enable SiFive fu540 PWM driver.
- Support SiFive fu540: SPI boot.
- Update OpenSBI used for RISC-V CI testing.
- Revert "riscv: Allow use of reset drivers".
- Revert "Revert "riscv: sifive: fu540: Add gpio-restart support"".
- sysreset: syscon:
        - Don't assume default value for offset and mask property.
        - Support value property.
- qemu: Add syscon reboot and poweroff support.
- Fix SIFIVE debug serial dependency.
- Fix linking error when building u-boot-spl with no SMP support.
- AE350 use fdtdec_get_addr_size_auto_noparent to parse smc reg.
- Make memory node available to SPL in hifive-unleashed-a00-u-boot.dtsi
- SiFive fu540 avoid using hardcoded ram base and size.
2020-07-24 08:43:08 -04:00
Tom Rini
7208396bbf Revert "Merge tag 'dm-pull-20jul20' of git://git.denx.de/u-boot-dm"
This reverts commit 5d3a21df66, reversing
changes made to 56d37f1c56.

Unfortunately this is causing CI failures:
https://travis-ci.org/github/trini/u-boot/jobs/711313649

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-24 08:42:06 -04:00
Rick Chen
e8fa43182a riscv: ae350: Use fdtdec_get_addr_size_auto_noparent to parse smc reg
Use fdtdec_get_addr_size_auto_noparent to read the "reg" property
instead of fdtdec_get_addr. This will increase the compatibility
of dtb parsing.

Signed-off-by: Rick Chen <rick@andestech.com>
Acked-by: Leo Liang <ycliang@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Leo Liang <ycliang@andestech.com>
2020-07-24 14:56:24 +08:00
Bin Meng
a0cc38ab44 riscv: qemu: Add syscon reboot and poweroff support
This adds syscon reboot and poweroff support to QEMU RISC-V.

Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
2020-07-24 14:55:55 +08:00
Bin Meng
265d46ba13 Revert "Revert "riscv: sifive: fu540: Add gpio-restart support""
This reverts commit 23da3c682a.

Now the build failure of sifive_fu540_defconfig board has been fixed,
revert this "revert patch".

Signed-off-by: Bin Meng <bin.meng@windriver.com>
2020-07-24 14:55:31 +08:00
Jagan Teki
662d518e8a sifive: fu540: Mark the default env as SPI flash
Mark the default U-Boot environment as SPI flash since
this is an on board flash device.

Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
2020-07-24 14:55:19 +08:00
Jagan Teki
868e295ef7 sifive: fu540: Add runtime boot mode detection
Add support to detect boot mode at runtime for
SiFive FU540 boards.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
2020-07-24 14:55:19 +08:00
Pragnesh Patel
3d5ac3536b riscv: sifive: fu540: Enable SiFive PWM driver
This patch enables SiFive PWM driver for the SiFive
Unleashed board.

Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
2020-07-24 14:55:11 +08:00
Tom Rini
5d3a21df66 binman support for FIT
new UCLASS_SOC
 patman switch 'test' command
 minor fdt fixes
 patman usability improvements
 -----BEGIN PGP SIGNATURE-----
 
 iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8V+WQRHHNqZ0BjaHJv
 bWl1bS5vcmcACgkQfxc6PpAIrebNgAgAmgHHPakg1fkJT8xZkbPD53r21t5fkF7h
 JTLVU93BKfC+Zz2bbizCEkCl9L9bdHSaSzJY5rb07E24yV/zwDcIkRApCmkDjVHN
 EHOb0P36Ht9acowSd5kN66wd2z0Q/V+7lfEdB6Adtprh0vVaWIKYtLPxogpRv6k9
 l/CaGsBCwvupmPeHZcE3pVQlflbKyYzp62VObEBI4RIJLisvDXaPRUcBa4vz904P
 yu0baIYW8hWBcZhb0Lkex/9x7ys2T1bnnw8G7WL05GtHSZfVvT46Y70o+3i5ycBh
 GAI93Lx4r1gCjol9LVE4i1bewbPiMqyNXOtKGPRt/IIvYI4HZ67lFA==
 =YIpM
 -----END PGP SIGNATURE-----

Merge tag 'dm-pull-20jul20' of git://git.denx.de/u-boot-dm

binman support for FIT
new UCLASS_SOC
patman switch 'test' command
minor fdt fixes
patman usability improvements
2020-07-23 15:56:06 -04:00
Tom Rini
95fc1f1647 Merge tag 'u-boot-rockchip-20200722' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- New rk3326 board: Hardkernel Odroid Go2;
- Update board config and dts for RockPI 4/N8/N10;
- Update led boot on support for roc-rk3399-pc;
- Enable SPI Flash suppor for rk3328 rock64 board;
- Update rockchip pcie phy to use generic framework;
2020-07-22 11:30:52 -04:00
Jagan Teki
6d06ea6c94 rockchip: roc-rk3399-pc: Set LED only during POR and pwr_key=y
ROC-RK3399-PC has specific set of configurations for
on-board led setup.

Due to easiness for user to know the state of the board
roc-rk339-pc board code will setup the low power led
on/off, and waiting for user to press power key and then
glow full power led.

All this needs to happen only during power-on-reset not
for soft reset or WDT.

Also, it is not a proper usage to ask the user to press
the Power key if the board connected remotely, so add
the environment variable 'pwr_key' to check as well.

So, user need to press Power key only
- during POR
- pwr_key=y

Tested-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22 20:55:13 +08:00
Jagan Teki
9aed288060 rockchip: roc-rk3399-pc: Add custom led_setup()
roc-rk3399-pc has some specific requirements to support LEDS,
environment. board detection and etc prior to U-Boot proper.

So as of now SPL would be a better stage for these custom board
requirements to support unlike TPL. Adding few of these custom
requirements like LEDS in TPL would require extra code pulling
and also the size of TPL can grow.

So, this patch moves the leds code from TPL into SPL Board init
led_setup code.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(split tpl.c change as separate patch)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22 20:55:13 +08:00
Jagan Teki
1f1395405f arm64: dts: rockchip: Add Radxa ROCK Pi 4C support
Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enabled
GPIO pin change compared to 4B, 4C.

So, add or enable difference nodes/properties in 4C dts
by including common dtsi.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22 20:55:13 +08:00
Heiko Stuebner
02ce99ec91 rockchip: board: add Hardkernel Odroid Go2 board
Also known as Odroid Go Advance but named Go2 internally by the
vendor it seems.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22 20:21:23 +08:00
Michal Simek
2feb4ea9dd ARM: rmobile: Switch back to fdtdec_setup_memory/banksize_fdt()
The commit 361377dbdb ("ARM: rmobile: Merge prior-stage firmware DT
fragment into U-Boot DT on Gen3") reverted changes introduced by commit
175f502734 ("ARM: renesas: Configure DRAM size from ATF DT fragment")
that's why there is no reason to use functions with _fdt() suffix because
parameter is gd->fdt_blob as is already for functions without _fdt()
suffix.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-20 11:37:47 -06:00
Stefan Roese
5fef24c912 mips: octeon: Add minimal Octeon 3 EBB7304 EVK support
This patch adds very basic minimal support for the Marvell Octeon 3
CN73xx based EBB7304 EVK. Please note that the basic Octeon port does
not support DDR3/4 initialization yet. To still use U-Boot on with this
port, the L2 cache (4MiB) is used as RAM. This way, U-Boot can boot
to the prompt on this board.

Supported devices:
- UART
- reset
- CFI parallel NOR flash

Signed-off-by: Stefan Roese <sr@denx.de>
2020-07-18 15:47:50 +02:00
Holger Brunck
b72bbf575b board/km: update MAINTAINERS email
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
2020-07-17 10:47:19 -04:00
Masahiro Yamada
b75d8dc564 treewide: convert bd_t to struct bd_info by coccinelle
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:

  It's a **mistake** to use typedef for structures and pointers.

Besides, using typedef for structures is annoying when you try to make
headers self-contained.

Let's say you have the following function declaration in a header:

  void foo(bd_t *bd);

This is not self-contained since bd_t is not defined.

To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>

  #include <asm/u-boot.h>
  void foo(bd_t *bd);

Then, the include direcective pulls in more bloat needlessly.

If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:

  struct bd_info;
  void foo(struct bd_info *bd);

Right, typedef'ing bd_t is a mistake.

I used coccinelle to generate this commit.

The semantic patch that makes this change is as follows:

  <smpl>
  @@
  typedef bd_t;
  @@
  -bd_t
  +struct bd_info
  </smpl>

Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
2020-07-17 09:30:13 -04:00
Tom Rini
42e7659db0 i.MX for 2020.10
----------------
 
 - i.MX DDR driver fix/update for i.MX8M
 - i.MX pinctrl driver fix.
 - Use arm_smccc_smc to remove imx sip function
 - i.MX8M clk update
 - support booting aarch32 kernel on aarch64 hardware
 - fused part support for i.MX8MP
 - imx6: pcm058 to DM
 
 Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXxCxWw8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76bPyACcDZ8gD9jf1P/Zh+7kqrGdIWwURF8AnAiEtNnu
 FhE/WQQj4mAEWE4F2bFE
 =7ceG
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20200716' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

i.MX for 2020.10
----------------

- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM

Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
2020-07-17 08:04:28 -04:00
Lukasz Majewski
949feef062 arm: Add extra boot device (UART) to run Ymodem u-boot.img boot on XEA (imx28)
This commit enables imx28 based XEA board's u-boot.sb (SPL) to download
u-boot proper (u-boot.img) via Ymodem protocol.

This is extremely useful in the recovery scenario where u-boot.sb is
downloaded via uuu utility to SDRAM [*], and then one can upload u-boot
proper via serial console to fully debrick the device.

Note - debricking procedure of imx28 devices:
- NXP's original USB based tools (like mxsldr or uuu) expect single
  u-boot.sb which is a relic of the old U-Boot (~2013) without SPL and
  U-Boot proper distinction.

[*] On Host:
------------
cat << EOF > imx28_xea.lst
uuu_version 1.3.0
SDPS: boot -f /srv/tftp/xea/u-boot.sb
SDPU: done
EOF

Please start picocom:
sudo picocom -b 115200 -s "sz -vv" /dev/ttyUSB1
sudo ./uuu/uuu -V imx28_xea.lst

On the U-boot console one shall see:
Trying to boot from UART
CCC

Then please press CTRL+A, S
and type u-boot.img

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
2020-07-16 11:20:33 +02:00
Sébastien Szymanski
eefd93e7f8 power: pmic_pca9450: fix PCA9450A I2C address
Quoting Ye Li from NXP:

    "We have confirmed with PMIC team, 0x35 is used only on early chips
    and not used any more. 0x25 is the final address."

Fix it by merging power_pca9450a_init and power_pca9450b_init into one
function power_pca9450_init.

Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
2020-07-16 11:20:14 +02:00
Fabio Estevam
496cb1f274 pico-imx6ul: Fix Quick Start Guide URL
The current URL for the pico imx6ul board is not valid anymore. Change
to a different URL that works.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-07-16 11:20:02 +02:00
Niel Fourie
26a6ed1b2e arm: imx6q: pcm058: Convert pcm058 to use DM with DTs
Convert pcm058 support to use device trees and the driver model.
Add rudimentary boot scripts to the environment, expand README.

Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2020-07-14 11:46:04 +02:00
Niel Fourie
7e64182ef4 arm: imx6q: pcm058: change MAINTAINER
Change the MAINTAINER of pcm058.

Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2020-07-14 11:46:04 +02:00
Peng Fan
3c41728d80 imx8m: Refactor the OPTEE memory removal
Current codes assume the OPTEE address is at the end of first DRAM bank.
Adjust the process to allow OPTEE in the middle of first bank.

When OPTEE memory is removed from first bank, it may split the first bank
to two banks, adjust the MMU table for the split case,
Since the default CONFIG_NR_DRAM_BANKS is 4, it is enough, just enlarge
i.MX8MP evk to default to avoid issue.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Silvano di Ninno <silvano.dininno@nxp.com>
Tested-by: Silvano di Ninno <silvano.dininno@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:48 +08:00
Jian Li
3f63d27c17 imx8mp: Disables use of MR4 TUF flag (MR4[7]) bit
In uMCTL2 Databook, for LPDDR4, it is recommended to set
this register to 1. This can avoid ddr bandwidth is lower
after booting with running for a while.

Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Jian Li <jian.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:46 +08:00
Jian Li
5865d14dde imx8mp: DDR performance tunning
1. set SCHED.rdwr_idle_gap=0
2. set SCHED.pageclose=1

Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Jian Li <jian.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:46 +08:00
Jian Li
dd2f41370d imx8mp: enable rd_port_urgent
Need to enable read urgent for NoC panic signal

Signed-off-by: Jian Li <jian.li@nxp.com
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:46 +08:00
Tom Rini
58ad372c49 omap3_beagle: Finish current outstanding DM migrations
At this point in time we can now remove our legacy code and switch to
enabling DM for USB and Ethernet.

Cc: Derald D. Woods <woods.technical@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
2020-07-13 20:58:34 +05:30
Adam Ford
7bb33e4684 ARM: da850-evm: Unify config options with Kconfig
There are two options that are currently whitelisted, but they
are redundant, because there are not necessary since Kconfig options
exist to basically state the same thing.

CONFIG_DIRECT_NOR_BOOT and CONFIG_USE_NOR are both set together and
only used by the da850 when booting from NOR, however the only time
CONFIG_MTD_NOR_FLASH is configured is when booting from NOR. Since
NOR doesn't need SPL, the options for SPL can be moved to a check for
building SPL instead of checking for NOR.

This patch removes the checks for these two config options and unifies
the checks around the Kconfig option of CONFIG_MTD_NOR_FLASH.

Since this board is the only board that uses these two config options,
they can be removed from the whitelist table.

Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-13 20:58:34 +05:30
Tom Rini
497c7598c4 Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-spi
- Enable DM_SPI on siemens omap boards (Jagan)
- Dropped some non-dm supported omap3 boards (Jagan)
- Dropped non-dm code in omap3 spi driver (Jagan)
- Dropped non-dm code in kirkwood spi driver (Bhargav)
2020-07-11 17:40:00 -04:00
Walter Lozano
e3e2470fdd drivers: rename drivers to match compatible string
When using OF_PLATDATA, the bind process between devices and drivers
is performed trying to match compatible string with driver names.
However driver names are not strictly defined, and also there are different
names used when declaring a driver with U_BOOT_DRIVER, the name of the
symbol used in the linker list and the used in the struct driver_info.

In order to make things a bit more clear, rename the drivers names. This
will also help for further OF_PLATDATA improvements, such as checking
for valid driver names.

Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a fix for sandbox of-platdata to avoid using an invalid ANSI colour:
Signed-off-by: Simon Glass <sjg@chromium.org>
2020-07-09 18:57:22 -06:00
Jagan Teki
f247354708 arm: Remove mx31pdk board
DM, OF_CONTROL, DM_SPI and other driver model migration
deadlines are expired for this board.

Remove it.

Acked-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-07-09 20:58:06 +05:30
Jagan Teki
bb1cbb2ba6 arm: Remove pengwyn board
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-07-09 20:58:06 +05:30
Jagan Teki
bce26c45e2 arm: Remove pepper board
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-07-09 20:58:05 +05:30
Jagan Teki
37559488a9 arm: Remove bav335x board
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Cc: Gilles Gameiro <gilles@gigadevices.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-07-09 20:58:05 +05:30
Jagan Teki
45833e25fc arm: Remove cairo board
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.

Drop it.

Cc: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-07-09 20:58:05 +05:30
Jagan Teki
d78b9df763 logicpd: Drop omap3 zoom1
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.

Drop it.

Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-07-09 20:58:05 +05:30
Jagan Teki
ed3294d6d1 arm: Remove overo board
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.

Drop it.

Cc: Ash Charles <ash@gumstix.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-07-09 20:58:05 +05:30
Jagan Teki
76386d6195 arm: Remove cm_t35 board
DM, DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-07-09 20:58:05 +05:30
Jagan Teki
a25aea733d arm: Remove cm_t54 board
DM, DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-07-09 20:58:05 +05:30
Simon Guinot
21b1c75f9d arm: kirkwood: enable DM_ETH for LaCie board
This patch enables DM_ETH for the following Kirkwood-based LaCie boards:

- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2020-07-09 06:51:20 +02:00
Simon Guinot
ca6f44ec19 arm: kirkwood: add DT spi0 alias to LaCie boards
The spi0 alias is needed by the environment code to retrieve the SPI
flash. This patch adds some -u-boot.dtsi files, providing the spi0
aliases, for all the following Kirkwood-based LaCie boards:

- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2

Note that this -u-boot.dtsi files will be removed as soon as the spi0
aliases will be available in the upstream Linux dtsi files.

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-07-09 06:51:20 +02:00
Tom Rini
186529953f - Add proper Odroid-N2 board support code
- Add support for Odroid-C4 single board computer
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAl8FyysACgkQd9zb2sjI
 SdFuBBAAqLO0rijSpibZYIER77wdV4oXl0w6D2gZ1iyfx0VFvcRSJ2dUQctruUO7
 5NqkAeVMabNIPwR/VoS6/QWmiBGmC/Yo5QAhGZs232Er5KzDPY75rVGwjkrTZrsc
 PrqWFz4cq/3KqlEZuZtamw0ArMcQ9+nHIwLVIqsTCs3Jz7X/UieClf0PuDGJtvtn
 Vs25GfxY6sldXpJ/5hLPaQsowKlbUfXyi/f/TfY9tDcHMv84jjU1d57G4NPp6TY4
 nqzkKumTKlpu4MykdthsxwkkDIRHCmatt03qUnUd0ell1qgYZQYT5+GhiXuvIxBy
 SgXeuiLlNa8Zrx5LvLcThtQ0B4Iw9CM/wTsLXQAZhBqbx7hc5en94bF1xWjtQVGO
 lPkHmKgB85uVCHUPTEqUTC6ltWT41Yi/N3by3+F2Dk+f8pOSB7H3Af/KMKf/KnRz
 QtakqPdGYHp8X/F5m8fA+GPqVI2To9PZoM9l34IWP6YDuuvLicdVaAF5LtOvoTIW
 g6J9NG9H46/yUjzK+gxNlRY++hKhjLgDZjZpVMK4b5RO8kVWXUvLdwHHu5q+sfZM
 ypS4Tv1TRGkvSvMMai5/1L3odKtbLxoUhtJWSfpTe7qNlBdQ4/w9HhGs8EiVxkDq
 IM7y2DbMNOBk7nxatK0Hw8bbj8/uWiA+SuYoq2qDdxAFTL8Rgzo=
 =2GPw
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-amlogic-20200708' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic

- Add proper Odroid-N2 board support code
- Add support for Odroid-C4 single board computer
2020-07-08 10:40:32 -04:00
Christian Hewitt
8888d83773 boards: amlogic: add Odroid C4 support
Odroid C4 is an Amlogic SM1 device, the board config and board documentation
are adapted from the Odroid-N2 support from the same vendor.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: fix odroid-c4.rst typos and structure]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
2020-07-08 10:52:45 +02:00
Pascal Vizeli
6de936b011 board: amlogic: Add Odroid-N2 board support
Add a proper Odroid-N2 board support to handle the Ethernet MAC
address stored in the in-SoC eFuses.

Signed-off-by: Pascal Vizeli <pvizeli@syshack.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
2020-07-08 10:52:45 +02:00
Tom Rini
526fe06a5d Merge tag 'u-boot-rockchip-20200708' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- dts sync from kernel for rk3399 boards;
- Add Radxa Rock Pi N8, N10;
- Some feature update for Pinebook Pro;
2020-07-07 23:05:57 -04:00
Andre Przywara
eb6211171d arm: juno: Enable PCI
The ARM Juno boards in their -r1 and -r2 variants sport a PCIe
controller, which we configure already in board specific code to be ECAM
compliant. Hence we can just enable the generic ECAM driver to let
U-Boot use PCIe devices.

Add the respective options to the Juno defconfig to enable the PCI
framework and the generic ECAM driver, and initialise the driver upon
loading U-Boot.

Make some functions in the Juno PCIe init code static on the way.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2020-07-07 18:23:48 -04:00
Andre Przywara
cc696e7cae arm: juno: Enable DM_ETH
The smc911X driver is now DM enabled, so we can switch the Juno board
over to use DM_ETH for the on-board Fast Ethernet device.
Works out of the box by using the DT.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2020-07-07 18:23:48 -04:00
Patrick Delaunay
6826d0d82b board: dh_stm32mp1: update the gpio hog support
This patch update the current gpio hog implementation with
the new API gpio_hog_probe_all() activated with CONFIG_GPIO_HOG.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-07-07 16:01:23 +02:00
Patrick Delaunay
03fb03842a board: st: move type-c stusb1600 controller code in a driver
Migrate the ST Microelectronics STUSB160X Type-C controller code in
a generic I2C driver in st/common, based on Linux one in :
drivers/usb/typec/stusb160x.c

This patch simplifies the stm32mp1 board code and allows to reuse
this STUSB160X driver in other boards.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-07-07 16:01:23 +02:00
Patrick Delaunay
42400228dc board: st: stm32mp1: increase teed partition
With TEE 3.7.0, the partition teed (OP-TEE pageable
code and data) need to increase up to 512KB in NOR device.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-07-07 16:01:23 +02:00
Patrick Delaunay
29e4ce3c97 board: stm32mp1: update the gpio hog support
This patch updates the current gpio hog implementation and uses
the new API gpio_hog_probe_all(), activated with CONFIG_GPIO_HOG.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-07-07 16:01:23 +02:00
Patrick Delaunay
4fb46816c7 board: stm32mp1: move the function board_debug_uart_init in spl.c
Move the debug function board_debug_uart_init in spl.c
as the debug_uart_init() function is called in arch_cpu_init()
only for SPL and remove the board.c file.

For TFABOOT, the UART TX pin configuration is done in TF-A.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-07-07 16:01:23 +02:00
Patrick Delaunay
2f238327b7 board: stm32mp1: update vddcore in SPL
For board using STPMIC1, the vddcore is provided by BUCK1 of STPMIC1
and need to be updated for 800MHz support and only after the clock
tree initialization.

The VDDCORE voltage value is provided by clock driver, saved in global
variable opp_voltage_mv and udpated in SPL board_early_init_f(),
just after clock tree initialization.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-07-07 16:01:23 +02:00
Patrick Delaunay
d1a4b09de6 board: st: stpmic1: add function stpmic1_init
Add a function stmpic_init to early initialize the PMIC STPMIC1
- keep vdd on during the reset cycle (to avoid issue when backup battery
  is absent)
- Check if debug is enabled to program PMIC according to the bit

This patch allows to remove the compilation of spl.c file from stm32mp1
board in dh_stm32mp1.

CONFIG_SPL_BOARD_INIT is removed as the new function is called earlier
in SPL, in the function board_early_init_f.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-07-07 16:01:23 +02:00
Patrick Delaunay
918e9c3d63 board: st: create common file stpmic1.c
Move function board_ddr_power_init() in a new file stpmic1 in
board/st/common to avoid duplicated code in each board using
stpmic1

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-07-07 16:01:23 +02:00
Jagan Teki
ad277eb458 ARM: dts: rockchip: Add Radxa Rock Pi N8 initial support
Rock Pi N8 is a Rockchip RK3288 based SBC, which has
- VMARC RK3288 SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.

VAMRC RK3288 SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N8 SBC.

So, add initial support for Rock Pi N8 by including rk3288,
rk3288 vamrc-som and raxda dalang carrier board dtsi files.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-07 19:45:57 +08:00
Jagan Teki
b1fccd3c0c arm64: dts: rockchip: Add Radxa Rock Pi N10 initial support
Rock Pi N10 is a Rockchip RK3399Pro based SBC, which has
- VMARC RK3399Pro SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.

VAMRC RK3399Pro SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N10 SBC.

So, add initial support for Rock Pi N10 by including rk3399,
rk3399pro vamrc-som and raxda dalang carrier board dtsi files.

rk3399pro-rock-pi-n10.dts was synced from linux-next v5.7-rc1.

Tested
- ROCK PI N10 Model B
- ROCK PI N10 Model C
- Boot from SD

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-07 19:45:57 +08:00
Tom Rini
23da3c682a Revert "riscv: sifive: fu540: Add gpio-restart support"
As part of merging the next branch in to master, the sifive_fu540 will
fail to link:
riscv64-linux-ld.bfd: lib/built-in.o: in function `panic_finish':
lib/panic.c:28: undefined reference to `do_reset'
make[2]: *** [spl/u-boot-spl] Error 1
make[1]: *** [spl/u-boot-spl] Error 2
make: *** [sub-make] Error 2

And while the "fix the build" option of enabling CONFIG_SPL_SYSRESET may
solve the issue, it is unclear that it is the correct path exactly.  For
the moment, I am reverting this commit and take a "revert the revert"
and proper fix as soon as it's available.

This reverts commit cdae446461.

Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Anup Patel <anup.patel@wdc.com>
Cc: Atish Patra <atish.patra@wdc.com>
Cc: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-06 17:57:47 -04:00
Tom Rini
6e7d7aa2e2 Merge branch 'next'
Merge all outstanding changes from the current next branch in now that
we have released.
2020-07-06 15:46:38 -04:00
Pragnesh Patel
5ce50206ed riscv: sifive: fu540: enable all cache ways from U-Boot proper
Add L2 cache node to enable all cache ways from U-Boot proper.

Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2020-07-03 15:09:06 +08:00
Bin Meng
cdae446461 riscv: sifive: fu540: Add gpio-restart support
The HiFive Unleashed board wires GPIO pin#10 to the input of the
system reset signal. This adds gpio reboot support.

Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Sagar Kadam <sagar.kadam@sifive.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
2020-07-03 15:07:54 +08:00
Sean Anderson
a7c81fc853 riscv: Add Sipeed Maix support
The Sipeed Maix series is a collection of boards built around the RISC-V
Kendryte K210 processor. This processor contains several peripherals to
accelerate neural network processing and other "ai" tasks. This includes a
"KPU" neural network processor, an audio processor supporting beamforming
reception, and a digital video port supporting capture and output at VGA
resolution. Other peripherals include 8M of sram (accessible with and
without caching); remappable pins, including 40 GPIOs; AES, FFT, and SHA256
accelerators; a DMA controller; and I2C, I2S, and SPI controllers. Maix
peripherals vary, but include spi flash; on-board usb-serial bridges; ports
for cameras, displays, and sd cards; and ESP32 chips. Currently, only the
Sipeed Maix Bit V2.0 (bitm) is supported, but the boards are fairly
similar.

Documentation for Maix boards is located at
<http://dl.sipeed.com/MAIX/HDK/>.  Documentation for the Kendryte K210 is
located at <https://kendryte.com/downloads/>. However, hardware details are
rather lacking, so most technical reference has been taken from the
standalone sdk located at
<https://github.com/kendryte/kendryte-standalone-sdk>.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
2020-07-01 15:01:22 +08:00
Tom Rini
50b5326868 ti814x: Remove platform
The TI814x (DM814x) platform is rather old and in need of a lot of
migration work.  As much of that work is well past the deadline, remove
this platform.

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-30 15:02:45 -04:00
Tom Rini
a3e7750d58 am335x: Update list of defconfigs
Both the am335x_boneblack and am335x_evm_usbspl configs have been gone
for a while, remove their entries from MAINTAINERS.

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-30 13:09:26 -04:00
Marcel Ziswiler
3450f626ba colibri_pxa270: add mmc platform data
Add MMC platform data.

While at it also fix trivial checkpatch.pl issues.

Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2020-06-30 11:13:11 -04:00
Lukasz Majewski
56c4046038 spi: Convert CONFIG_DM_SPI* to CONFIG_$(SPL_TPL_)DM_SPI*
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.

Before this change it was necessary to use:
    /* SPI Flash Configs */
    #if defined(CONFIG_SPL_BUILD)
    #undef CONFIG_DM_SPI
    #undef CONFIG_DM_SPI_FLASH
    #undef CONFIG_SPI_FLASH_MTD
    #endif

in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.

The goal of this patch:

Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.

Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).

In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):

- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
  run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
  environment with no fitImage and OF_LIBFDT support).

Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.

This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-29 13:34:43 -04:00
Tom Rini
0567099bea arm: imx: Finish migration from CONFIG_SECURE_BOOT to CONFIG_IMX_HAB
There are a few remaining places where we say CONFIG_SECURE_BOOT rather
than CONFIG_IMX HAB.  Update these instances.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2020-06-26 10:29:06 -04:00
Tom Rini
f0e236c8d6 Xilinx changes for v2020.10
Versal:
 - xspi bootmode fix
 - Removing one clock from clk driver
 - Align u-boot memory setting with OS by default
 - Map TCM and OCM by default
 
 ZynqMP:
 - Minor DT improvements
 - Reduce console buffer for mini configurations
 - Add fix for AMS
 - Add support for XDP platform
 
 Zynq:
 - Support for AES engine
 - Enable bigger memory test by default
 - Extend documentation for SD preparation
 - Use different freq for Topic miami board
 
 mmc:
 - minor GD pointer removal
 
 net:
 - Support fixed-link cases by zynq gem
 - Fix phy looking loop in axi enet driver
 
 spi:
 - Cleanup global macros for xilinx spi drivers
 
 firmware:
 - Add support for pmufw reloading
 
 fpga:
 - Improve error status reporting
 
 common:
 - Remove 4kB addition space for FDT allocation
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
 IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
 =2Yuu
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next

Xilinx changes for v2020.10

Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default

ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform

Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board

mmc:
- minor GD pointer removal

net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver

spi:
- Cleanup global macros for xilinx spi drivers

firmware:
- Add support for pmufw reloading

fpga:
- Improve error status reporting

common:
- Remove 4kB addition space for FDT allocation
2020-06-25 09:33:39 -04:00
Michal Simek
e20d88bffa xilinx: zynqmp: Enable pmufw config reloading
PMU FW has functionality to accept and reload configuration object at run
time. The patch is adding support for doing it via u-boot prompt.

For example:
tftpboot 100000 pmu_obj.bin
zynqmp pmufw 100000 $filesize

The most of pmufw configurations don't allow config reloading.
Also official Xilinx PMUFW doens't support this feature properly but the
patch should open a way to call PMUFW with this request.

Here is example of PMUFW config fragment which enables config reloading.

/* SET CONFIG SECTION */
PM_CONFIG_SET_CONFIG_SECTION_ID,        /* Section ID */
PM_CONFIG_IPI_PSU_CORTEXA53_0_MASK | PM_CONFIG_IPI_PSU_CORTEXR5_0_MASK |
PM_CONFIG_IPI_PSU_CORTEXR5_1_MASK, /* Permissions to set config */

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-25 10:08:04 +02:00
Michal Simek
3ccea69fc4 arm64: zynqmp: Print multiboot reg in decimal
It is better to print multiboot value in decimal because boot images are
also composed in decimal not in hex.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-25 10:08:04 +02:00
Mike Looijmans
39c5cf0e70 topic: zynqmp: Add support for zynqmp-xilinx-xdp platform
XDP - Xilinx Drone Platform is a board for drones or other UAV.

Pinmux the SD card by default, and if the SD card detect line is high
(inactive) then pinmux the SD1 interface to EMIO instead. SD is placed on
extension card and shares connection with on board wife. That means that
when SD card is present in the board wifi can't be used.

There seems to be an issue with DDR access from PL at 2400MT/s, after
updating the PMU and ATF firmware this is causing extremely slow DDR
access. Reducing the DDR speed from 2400 to 2133 appears to solve that
issue, even though the hardware has proven to be 2400 capable.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24 13:11:08 +02:00
Mike Looijmans
dfbe492ede board: zynqmp: Fix for wrong AMS setting by ROM
A bug in the ZynqMP bootrom sets the PS_SYSMON_ANALOG_BUS register
at 0xFFA50914 to the wrong value 0x3201. This causes the AMS to
exchange the PS supply voltages 0 and 1. On Xilinx boards this is
not noticeable since these are tied together, it's only really
noticeable if banks 500 and 501 have different supplies. Xilinx' tech
support reported this undocumented register to be the cause, and
this patch applies a fix for all boards by programming the correct
value.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24 13:11:08 +02:00
Mike Looijmans
fe1eb9945b board: topic-miami: Set FCLK1 to 150MHz
In all reference designs the FCLK1 runs at 150MHz, but the bootloader
doesn't set it up like that. Set the divider to 8 to generate the
correct clock. Fixes (a.o.) the DMA speed being too slow.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24 13:11:08 +02:00
T Karthik Reddy
b80a476faa fpga: zynqpl: Add zynq aes load & loadp commands
Added support for zynq aes load & loadp commands.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24 13:07:58 +02:00
Siva Durga Prasad Paladugu
3427f4d204 fpga: zynqpl: Correct PL bitstream loading sequence for zynqaes
Correct the PL bitstream loading sequence for zynqaes command by
clearing the loaded PL bitstream before loading the new encrypted
bitstream using the zynq aes command. This was done by setting
the PROG_B same as in case of fpgaload commands.
This patch fixes the issue of loading the encrypted PL bitstream
onto the PL in which a bitstream has already been loaded
successfully.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24 13:07:57 +02:00
Walter Lozano
824e6fe0ae mx6cuboxi: remove unused code
After enabling SPL_OF_CONTROL, SPL_DM and SPL_DM_MMC the MMC
initialization code is not longer needed.

This patch removes the unused code.

Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
2020-06-23 00:08:53 +02:00
Walter Lozano
6c3fbf3e45 mx6cuboxi: customize board_boot_order to access eMMC
In SPL legacy code only one MMC device is created, based on BOOT_CFG
register, which can be either SD or eMMC. In this context
board_boot_order return always MMC1 when configure to boot from
SD/eMMC. After switching to DM both SD and eMMC devices are created
based on the information available on DT, but as board_boot_order
only returns MMC1 is not possible to boot from eMMC.

This patch customizes board_boot_order taking into account BOOT_CFG
register to point to correct MMC1 / MMC2 device. Additionally, handle
IO mux for the desired boot device.

Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
2020-06-23 00:08:53 +02:00
Oliver Graute
fb0b862e81 imx: imx8qm_rom7720_a1: update README
Update README to extract firmware from scripts

Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
2020-06-22 17:43:59 +02:00
Marek Vasut
ba78c25afe ARM: imx6: Fetch MAC address in board_init_late() on DH iMX6 PDK2
This is needed to obtain the MAC from EEPROM/OTP only after the final
env is populated, otherwise the ethaddr might be overriden.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Claudius Heine <ch@denx.de>
Cc: Harald Seiler <hws@denx.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
2020-06-22 17:43:51 +02:00
Heinrich Schuchardt
a1f79c2170 arm: wandboard: move CONFIG_MXC_UART to defconfig
For using a debug UART on the Wandboard CONFIG_MXC_UART=y must be set in
the .config file.

To avoid duplicate definitions move the setting from
include/configs/wandboard.h to configs/wandboard_defconfig.

Document the debug UART settings in the README.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-06-22 17:43:31 +02:00
Martyn Welch
f7ac30b042 Fix MMC access on Sabrelite
It appears that MMC access on the Sabrelite has been broken since
cdcaee9518:

Loading Environment from MMC... Card did not respond to voltage select!
*** Warning - No block device, using default environment

Remove the board_mmc_init() and related entries now that we should be
using DM_MMC, add PINCTRL so that things work as expected.

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
2020-06-22 17:43:20 +02:00
Fabio Estevam
d8da22c5db mx6cuboxi: Convert to DM_ETH
Migration to DM_ETH is mandatory, so convert mx6cuboxi to Ethernet
Driver Model.

This also brings the benefit of restoring Ethernet functionality.

Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tom Rini <trini@konsulko.com>
2020-06-22 17:41:06 +02:00
Tom Rini
5575f79bda Merge https://gitlab.denx.de/u-boot/custodians/u-boot-spi into next
- Convert fsl_espi to driver model (Chuanhua)
- Enable am335x baltos to DM_SPI (Jagan)
- Drop few powerpc board which doesn't have DM enabled (Jagan)
2020-06-19 16:25:50 -04:00
Tom Rini
d0cc022820 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-tegra 2020-06-19 12:41:05 -04:00
Tom Rini
04909251fd - migrate remaining imx5/imx6qd boards to DM_VIDEO
- use 'vidconsole' stdout in nitrogen6x upgrade script
 - add option for selection of the vidconsole commands
   lcdputs and setcurs
 - allow building ipuv3 driver with disabled CONFIG_PANEL
 - make backlight and panel drivers optional
 - remove useless code from ipuv3 driver
 - extend existing DM_VIDEO work-around for console name
   to support 'vga'
 - remove non-DM code in ipuv3
 -----BEGIN PGP SIGNATURE-----
 
 iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXuvRkA4cYWd1c3RAZGVu
 eC5kZQAKCRBM6ATMmsalXMpeAJkB/FzsJ3O7putHrbLKOrLRF3zZYwCfQxa9jKuh
 DXNTYVrHS/43T8ijGYo=
 =7G75
 -----END PGP SIGNATURE-----

Merge tag 'video-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-video into next

- migrate remaining imx5/imx6qd boards to DM_VIDEO
- use 'vidconsole' stdout in nitrogen6x upgrade script
- add option for selection of the vidconsole commands
  lcdputs and setcurs
- allow building ipuv3 driver with disabled CONFIG_PANEL
- make backlight and panel drivers optional
- remove useless code from ipuv3 driver
- extend existing DM_VIDEO work-around for console name
  to support 'vga'
- remove non-DM code in ipuv3
2020-06-18 16:59:16 -04:00
Igor Opaniuk
c46443dd85 colibri_t20: change maintainer
Take over maintainership for Colibri T20 module.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Lucas Stach <dev@lynxeye.de>
2020-06-18 13:15:02 -07:00
Anatolij Gustschin
1e916aa021 imx: convert cgtqmx6eval board to DM_VIDEO
Migration to DM_VIDEO driver is long overdue. Update defconfig
to enable usage of converted ipuv3 driver DM configuration.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
2020-06-18 19:37:49 +02:00
Anatolij Gustschin
ffd955c488 nitrogen6x: update video console name
After migration to DM 'vga' name is not longer supported,
Update the upgrade script to use 'vidconsole' instead.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
2020-06-18 19:25:05 +02:00
Jagan Teki
47df4b5f2a powerpc: Remove TWR-P1025_defconfig board
DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Patch-cc: Xiaobo Xie <xiaobo.xie@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-06-18 21:47:08 +05:30
Jagan Teki
5d226cd013 powerpc: Remove T4160QDS_NAND_defconfig board
DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-06-18 21:47:08 +05:30
Jagan Teki
ce17d99d12 powerpc: Remove T1040QDS_DDR4_defconfig board
DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Patch-cc: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-06-18 21:47:08 +05:30
Jagan Teki
7723a6deb7 powerpc: Remove T1024QDS_DDR4_SECURE_BOOT_defconfig board
DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-18 21:47:08 +05:30
Jagan Teki
197fc64578 powerpc: Remove P1022DS_36BIT_NAND_defconfig board
DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Patch-cc: Timur Tabi <timur@tabi.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-06-18 21:47:08 +05:30
Jagan Teki
8429b95167 powerpc: Remove configs/MPC8536DS_36BIT_defconfig board
DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Patch-cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-06-18 21:47:08 +05:30
Jagan Teki
447ec175b2 powerpc: Remove configs/C29XPCIE_NAND_defconfig board
DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Patch-cc: Po Liu <po.liu@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-06-18 21:47:08 +05:30
Jagan Teki
55bcea4fb4 powerpc: Remove configs/BSC9132QDS_NAND_DDRCLK100_SECURE_defconfig board
DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Patch-cc: Naveen Burmi <naveen.burmi@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-06-18 21:47:08 +05:30
Jagan Teki
f178468b5e powerpc: Remove configs/BSC9131RDB_NAND_SYSCLK100_defconfig board
DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Patch-cc: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-06-18 21:47:08 +05:30
Jagan Teki
e3e6782d47 powerpc: Remove configs/B4420QDS_NAND_defconfig board
DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Patch-cc: Ashish Kumar <ashish.kumar@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-06-18 21:47:08 +05:30