This patch
- consolidate CONFIG_SYS_NAND_xx and CONFIG_SPL_NAND_xx from various
configuration files into single file.
- update MTD Partition table to match AM335x_EVM DT in linux-kernel
- segregate CONFIGs based on different boot modes (like SPL and U-Boot)
Signed-off-by: Pekon Gupta <pekon@ti.com>
When we're using EMMC_BOOT that means we have environment on eMMC so
we can make use of CONFIG_SPL_ENV_SUPPORT within Falcon Mode.
Signed-off-by: Tom Rini <trini@ti.com>
On am335x_evm we only support USBETH for a networking SPL option so move
the rest of the defines under that area as that's the only time we need
(and want) environment support here.
Signed-off-by: Tom Rini <trini@ti.com>
This patch moves some board specific NAND configs:
- FROM: generic config file 'ti_armv7_common.h'
- TO: individual board config files using these configs.
So that each board can independently set the value as per its design.
Following configs are affected in this patch:
CONFIG_SYS_NAND_U_BOOT_OFFS: <refer doc/README.nand>
CONFIG_CMD_SPL_NAND_OFS: <refer doc/README.falcon>
CONFIG_SYS_NAND_SPL_KERNEL_OFFS: <refer doc/README.falcon>
CONFIG_CMD_SPL_WRITE_SIZE: <refer doc/README.falcon>
This patch also updates documentation for few of above NAND configs.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Fixes commit a0a37183bd
ARM: omap: merge GPMC initialization code for all platform
1) NAND device are not directly memory-mapped to CPU address-space, they are
indirectly accessed via following GPMC registers:
- GPMC_NAND_COMMAND_x
- GPMC_NAND_ADDRESS_x
- GPMC_NAND_DATA_x
Therefore from CPU's point of view, NAND address-map can be limited to just
above register addresses. But GPMC chip-select address-map can be configured
in granularity of 16MB only.
So this patch uses GPMC_SIZE_16M for all NAND devices.
2) NOR device are directly memory-mapped to CPU address-space, so its
address-map size depends on actual addressable region in NOR FLASH device.
So this patch uses CONFIG_SYS_FLASH_SIZE to derive GPMC chip-select address-map
size configuration.
Signed-off-by: Pekon Gupta <pekon@ti.com>
We don't make use of the device tree otherwise yet (and will need to
think how to not break the current multi-board support) and this causes
further breakage with additional changes.
Signed-off-by: Tom Rini <trini@ti.com>
Future patches will make DFU too large to fit in this board's SPL build.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Previously offsets handled by dfu_fill_entity_mmc(), defined in boards'
CONFIG_DFU_ALT were treated as hexadecimal regardless of their prefix,
which sometimes led to confusion. This patch forces usage of explicit
numerical base prefixes.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tom Rini <trini@ti.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
This is only useful with the _spiboot build target anyhow, so only
include it then. Drop CONFIG_SPL_OS_BOOT support then as the flash is
small and didn't include a spot for the device tree already.
Signed-off-by: Tom Rini <trini@ti.com>
To deal with a reoccurring problem properly we need to specify addresses
for the Linux kernel, Flatted Device Tree and ramdisk that obey the
constraints within the kernel's Documentation/arm/Booting file but also
make sure that we relocate things within a valid address range.
It is possible with these addresses to also set fdt_high and initrd_high
to the value of 0xffffffff. We don't do this by default to allow for
the most likely success of people using custom addresses however.
Signed-off-by: Tom Rini <trini@ti.com>
On the boards this target supports this option is either non possible
without hardware mods (Beaglebone White/Black) or not supported due to
board design. Drop this and regain some space.
Signed-off-by: Tom Rini <trini@ti.com>
When using the am335x_evm_nor target one is generally expecting to be
used in an environment when you want to program the NOR and not a
"deployment" type target. In addition this only supports the Beaglebone
White with the memory cape and NOR module installed, which precludes the
presence of SPI flash. Drop SPI as we were getting close to the binary
limit in some cases and slightly over with other toolchains.
Signed-off-by: Tom Rini <trini@ti.com>
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI
params or nand_id[] table. And based on that it defines ECC layout.
This patch
1) removes following board configs used for defining NAND ECC layout
- GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND)
- GPMC_NAND_ECC_LP_x8_LAYOUT (for large page x8 NAND)
- GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND)
- GPMC_NAND_ECC_SP_x8_LAYOUT (for small page x8 NAND)
2) removes unused #defines in common omap_gpmc.h depending on above configs
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>
This patch add support for the Silica Pengwyn board [1]
The board is based on a TI AM3354 CPU [2]
All jumpers removed it will boot from the SDcard, the console is on
UART1 accessible via the FDTI -> USB. The on board NAND flash is
supported and can act as boot medium, depending on jumper settings.
USB Host, USB Device and Ethernet are also provided but untested.
[1]
http://www.silica.com/product/silica-pengwyn-board.html
[2]
http://www.ti.com/product/am3354
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
[trini: Move CONFIG_BOARD_LATE_INIT into am335x_evm.h, drop unused
spi0_pin_mux from Pengwyn support]
Signed-off-by: Tom Rini <trini@ti.com>
To make managing the environment easier, add DFUARGS to
CONFIG_EXTRA_ENV_SETTINGS. Then we set DFUARGS down in the DFU part of
the file, and include (or not) the NAND part, based on if NAND is set.
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds new CONFIG_NAND_OMAP_ECCSCHEME, replacing other distributed
CONFIG_xx used for selecting NAND ecc-schemes.
This patch aims at solving following issues.
1) Currently ecc-scheme is tied to SoC platform, which prevents user to select
other ecc-schemes also supported in hardware. like;
- most of OMAP3 SoC platforms use only 1-bit Hamming ecc-scheme, inspite
the fact that they can use higher ecc-schemes like 8-bit ecc-schemes with
software based error detection (OMAP_ECC_BCH4_CODE_HW_DETECTION_SW).
- most of AM33xx SoC plaforms use 8-bit BCH ecc-scheme for now, but hardware
supports BCH16 ecc-scheme also.
2) Different platforms use different CONFIG_xx to select ecc-schemes, which
adds confusion for user while migrating platforms.
- *CONFIG_NAND_OMAP_ELM* which enables ELM hardware engine, selects only
8-bit BCH ecc-scheme with h/w based error-correction (OMAP_ECC_BCH8_CODE_HW)
whereas ELM hardware engine supports other ecc-schemes also like; BCH4,
and BCH16 (in future).
- *CONFIG_NAND_OMAP_BCH8* selects 8-bit BCH ecc-scheme with s/w based error
correction (OMAP_ECC_BCH8_CODE_HW_DETECTION_SW).
- *CONFIG_SPL_NAND_SOFTECC* selects 1-bit Hamming ecc-scheme using s/w library
Thus adding new *CONFIG_NAND_OMAP_ECCSCHEME* de-couples ecc-scheme dependency
on SoC platform and NAND driver. And user can select ecc-scheme independently
foreach board.
However, selection some hardware based ecc-schemes (OMAP_ECC_BCHx_CODE_HW) still
depends on presence of ELM hardware engine on SoC. (Refer doc/README.nand)
Signed-off-by: Pekon Gupta <pekon@ti.com>
ELM hardware engine which is used for ECC error detection, is present on all
latest OMAP SoC (like OMAP4xxx, OMAP5xxx, DRA7xxx, AM33xx, AM43xx). Thus ELM
driver should be moved to common drivers/mtd/nand/ folder so that all SoC
having on-chip ELM hardware engine can re-use it.
This patch has following changes:
- mv arch/arm/include/asm/arch-am33xx/elm.h arch/arm/include/asm/omap_elm.h
- mv arch/arm/cpu/armv7/am33xx/elm.c drivers/mtd/nand/omap_elm.c
- update Makefiles
- update #include <asm/elm.h>
- add CONFIG_NAND_OMAP_ELM to compile driver/mtd/nand/omap_elm.c
and include in all board configs using AM33xx SoC platform.
Signed-off-by: Pekon Gupta <pekon@ti.com>
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
Some am33xx boards may not use the RTC block for bootcount (as it may
not be wired up for the board) and use some other facility. So add
another symbol for the bootcount driver for the IP block.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Upon further inspection and review and chatting with kernel folks, what
happens here is that what mmcblk# a device gets is based on probe order.
So a system with an SD card inserted with place eMMC on mmcblk1, but
without an SD card, it will be on mmcblk0. So U-boot can only provide a
best guess. In this case, if no SD card is present, we would want to
pass mmcblk0p2 still. If an SD card is present, it woudl be able to
provide a uEnv.txt that would be loaded (even if the kernel is NOT
there) which can still update mmcroot variable.
This reverts commit 827512fb11.
Cc: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Tom Rini <trini@ti.com>
If, in CONFIG_BOOTCOMMAND, the environment switches both the mmcdev
and bootpart variables to refer to MMC device 1, it would make sense
that the mmcroot env variable should switch to that device as well.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Add a am33xx_spl_board_init (and enable the PMICs) that we may see,
depending on the board we are running on. In all cases, we see if we
can rely on the efuse_sma register to tell us the maximum speed. In the
case of Beaglebone White, we need to make sure we are on AC power, and
are on later than rev A1, and then we can ramp up to the PG1.0 maximum
of 720Mhz. In the case of Beaglebone Black, we are either on PG2.0 that
supports 1GHz or PG2.1. As PG2.0 may or may not have efuse_sma set, we
cannot rely on this probe. In the case of the GP EVM, EVM SK and IDK we
need to rely on the efuse_sma if we are on PG2.1, and the defaults for
PG1.0/2.0.
Signed-off-by: Tom Rini <trini@ti.com>
Somewhere along the line of refactoring the am335x header files, the
kernel image load was lost, so put it back in.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
We create two new files, include/configs/ti_armv7_common.h for all of
the common IP blocks and related features / commands we share in
virtually all of our platforms. We then create
include/configs/ti_am335x_common.h for everything common to the am335x
SoC leaving just the board specific parts to
include/configs/ti_am335x_common.h.
Signed-off-by: Tom Rini <trini@ti.com>
Adding a new CONFIG_OMAP_COMMON which is included by all boards
that needs to build cpu/armv7/omap-common folder.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some boards, such as the BeagleBone Black, have an eMMC chip intstead
of NAND. We can use the eMMC boot partition to store the environment,
since it isn't used for anything else. This allows us to have a
configurable environment on those boards.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
The BeagleBone Black can boot from either the MMC card
or eMMC chip on board. We should try both interfaces.
This modification also allows a graceful fallback if
a device exists but boot images are not present on it.
Changes for v2:
* Fix boot partition - it should always show up as mmcblk0p2
* Fix missing FDT load
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Many modern U-Boot ports enable command line editing and
a history buffer. The am335x_evm configuration is fairly
comprehensive as it is, so a few extra kb should not be
noticable, and it adds a very convenient feature.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Give the user the ability to disable NAND support by defining
CONFIG_NO_NAND. This will allow custom hardware to easily support
this configuration.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
[trini: Make apply on top of other series]
Signed-off-by: Tom Rini <trini@ti.com>
NOR requires that s_init be within the first 4KiB of the image so that
we can perform the rest of the required pinmuxing to talk with the rest
of NOR that we are found on. When NOR_BOOT is set we save our
environment in NOR at 512KiB and a redundant copy at 768KiB. We avoid
using SPL for this case and u-boot.bin is written directly to the start
of NOR.
We enclose the DMM-related parts of arch/arm/cpu/armv7/am33xx/emif4.c
with TI81xx checks as at this time U-Boot does not discard unused
sections in the main build and this code relies on functions specific to
(and only provided in) ti81xx-related code.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds support for the NOR module that attaches
to the memory cape for a Beaglebone board. This does not
add booting support; only support so that you can boot from
SD/MMC and see the NOR module so that it can be programmed.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Clean up config changes slightly]
Signed-off-by: Tom Rini <trini@ti.com>
- Style cleanup (# define -> #define)
- Due to ROM issues, redudant loading isn't feasible, so drop.
- Given extra space, increase max size of U-Boot to 512KiB
- Correct env size to match usage (we had not re-defined ENV_SIZE).
- Given extra space, keep env size as 128KiB, add redundant environment.
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
We always set a CONFIG_ENV_IS_...somewhere... so drop the initial define
of NOWHERE.
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
We use CONFIG_CMD_SPL_WRITE_SIZE when reading/writing the args portion
of falcon mode to NAND. Previously it was half the size of the
eraseblock which is too small, increase to eraseblock size.
Signed-off-by: Tom Rini <trini@ti.com>
The previous location used for the "args" portion of falcon mode was too
small to allow for a device tree to be saved there, so move the location
slightly and increase the size. In addition, our previous kernel
location was part of the area we set aside for U-Boot itself, so move it
up a bit higher.
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Now that we have falcon mode enabled, the partiton numbers for NAND have
changed, and we need to list entries for updating these parts of the
system. While adding falcon mode entires for eMMC (raw), we round up
the limit on U-Boot for ease of math later.
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
In a714321 we add a check at the end of findfdt to make sure we have
updated it from undefined and if not, warn the user. This however
forgot a ';' on the end of the previous last test.
Signed-off-by: Tom Rini <trini@ti.com>
There will need the environment in SPL for reasons other than network
support (in particular, hwconfig contains info for how to set up DDR).
Add a new symbol CONFIG_SPL_ENV_SUPPORT to replace CONFIG_SPL_NET_SUPPORT
for environment in common/Makefile.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In the omap4, omap5 and am335x common files add a check to ensure that the fdtfile is
defined after the findfdt macro has run. If the file is not defined then warn the user that the
dtb file is not defined.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Jump into full u-boot mode if a 'c' character is received on the uart.
We need to adjust the spl bss/malloc area to not overlap with the
loadaddr of the kernel (sdram + 32k), so move it past u-boot instead.
For raw mmc, we store the kernel parameter area in the free space after
the MBR (if used). For nand, we use the last sector of the partition
reserved for u-boot.
This also enables the spl command in the full u-boot so the kernel
parameter area snapshot can be created.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
The location of valid scratch space is dependent on SoC, so move that
there. On OMAP4+ we continue to use SRAM_SCRATCH_SPACE_ADDR. On
am33xx/ti814x we want to use what the ROM defines as "public stack"
which is the area after our defined download image space. Correct the
comment about and location of CONFIG_SPL_TEXT_BASE.
Signed-off-by: Tom Rini <trini@ti.com>
Prior to Sricharan's cleanup of the boot parameter saving code, we
did not make use of NON_SECURE_SRAM_START on am33xx, so it wasn't a
problem that the address was pointing to the middle of our running SPL.
Correct to point to the base location of the download image area.
Increase CONFIG_SPL_TEXT_BASE to account for this scratch area being
used. As part of correcting these tests, make use of the fact that
we've always been placing our stack outside of the download image area
(which is fine, once the downloaded image is run, ROM is gone) so
correct the max size test to be the ROM defined top of the download area
to where we link/load at.
Signed-off-by: Tom Rini <trini@ti.com>
---
Changes in v2:
- Fix typo noted by Peter Korsgaard
The boot parameters passed from SPL to UBOOT
must be saved as a part of uboot's gd data
as early as possible, before we will inadvertently
overwrite it. So adding a arch_cpu_init for the required
Socs to save it.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
[trini: Add igep0033 hunk]
Signed-off-by: Tom Rini <trini@ti.com>
The boot parameters are read from individual variables
assigned for each of them. This been corrected and now
they are stored as a part of the global data 'gd'
structure. So read them from 'gd' instead.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
[trini: Add igep0033 hunk]
Signed-off-by: Tom Rini <trini@ti.com>
As part of a review of a recent patch to add a new AM335x board, Tom
found several duplicate and/or unused #defines.
This patch simply removes them.
The two affected configs have been recompiled to check nothing was
broken (from a compilation point of view !!)
Reported-by: Tom Rini <trini@ti.com>
Signed-off-by: Mark Jackson <mpfj-list@mimc.co.uk>
- Add CONFIG_DFU_NAND, CONFIG_DFU_MMC
- Set dfu_alt_info_nand, dfu_alt_info_emmc and dfu_alt_info_mmc to show
working examples for those cases.
- Increase CONFIG_SYS_MAXARGS due to hush parsing bugs that would
otherwise disallow 'setenv dfu_alt_info ${dfu_alt_info_nand}'.
- Enable CONFIG_FAT_WRITE to allow updating on MMC
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
drivers/usb/gadget/composite.c requires that this is defined early.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
On TI AM335x devices, MUSB has bulk split/combine feature enabled
in the ConfigData register, but the current MUSB driver does not
support it yet. Therefore, disable the feature for now, until the
driver adds the support.
One usecase which is broken because of this feature is that Ether
gadget stops working in Fullspeed mode (by un-defining
CONFIG_USB_GADGET_DUALSPEED)
After desabled this feature, MUSB driver send packets in proper size
(no more than 64 bytes) in Fullspeed mode.
This has been validated with Ether gadget in Fullspeed mode on AM335x
EVM.
Signed-off-by: Bin Liu <b-liu@ti.com>
- In arch/arm/cpu/armv7/omap-common/timer.c,
drivers/mtd/nand/omap_gpmc.c and drivers/net/cpsw.c add #include files
that the driver needs but had been relying on <config.h> to bring in.
- In arch/arm/cpu/armv7/omap-common/lowlevel_init.S add <config.h>
- In am335x_evm.h and pcm051.h don't globally include
<asm/arch/hardware.h> and <asm/arch/cpu.h> but just <asm/arch/omap.h>
as that is the only include which defines things the config uses.
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
Make bootcmd run findfdt so that we know what dtb file to load. Add a
loadfdt command to load this file in. Make mmcboot pass in ${fdtaddr}
and make the mmc section of bootcmd run loadfdt.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
The kernel is loaded from some form of ext[234] or FAT, depending on the
distribution used. We add a bootpart variable to the environment so
that we can load from the correct mmc partition as well. We leave
CONFIG_CMD_EXT2 for existing scripts that use ext2load.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Many SPL linker scripts needlessly include linker lists (aka LGAs).
Remove them whenever possible; keep it only in the seven am335x_evm
variants (am335x_evm, am335x_evm_uart[1-5], am335x_evm_spiboot),
where there is actual content in output section .u_boot_list.
This commit keeps all u-boot.bin and u-boot-spl.bin in ARM targets
byte-identical.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
With v3.9 and later of the Linux Kernel defaulting to multi-platform
images with omap2plus_defconfig, uImage isn't builtable anymore by
default. Add CONFIG_CMD_BOOTZ so that we can still boot something the
kernel spits out.
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
We add USB (RNDIS gadget) SPL support as a separate target. We need to
pull out YMODEM support in order to be a small enough target binary.
Signed-off-by: Tom Rini <trini@ti.com>
Because of our support for network-based SPL, we don't discard all of
the environment related functions. We however never make use of the
default CONFIG_EXTRA_ENV_SETTINGS items and as this variable grows, it
brings us closer to (or with some toolchains, over) our SPL size limit.
Never set this in the case of SPL.
Signed-off-by: Tom Rini <trini@ti.com>
This target will move the environment into SPI flash and documents
the expected layout. We correct the SPL define for where U-Boot is
and remove an unused define.
Signed-off-by: Tom Rini <trini@ti.com>
* Added variables to support SPI booting
* Note that the first 512KiB are reserved for 4 copies of SPL.
Signed-off-by: Chase Maupin <Chase.Maupin@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
* Added support to the default environment variables for NAND
boot.
* Add nandboot to the default bootcmd.
Signed-off-by: Chase Maupin <Chase.Maupin@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This adds necessary config options and a new build target,
am335x_evm_usbspl, to enable usb booting and fixes board_eth_init()
function to take into account that we may have USB ether support in SPL
now. This uses the same MAC for both cpsw and USB, in order to match
ROM behavior.
The usbspl build target does not contain UART SPL, CPSW SPL or extra
environment settings, so that we may fit within our binary size
constraint.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Signed-off-by: Tom Rini <trini@ti.com>
For AM335X boards, such as the EVM and Bone Linux kernel fails to
locate the device tree blob on boot. The reason being is that
u-boot is copying the DT blob to the upper part of RAM when booting
the kernel and the kernel is unable to access the blob.
By setting the fdt_high variable to 0xffffffff (to prevent the copy)
the kernel is able to locate the DT blob and boot.
This patch is tested on BeagleBone platform.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Tom Rini <trini@ti.com>
We add CONFIG_ENV_VARS_UBOOT_CONFIG,
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and CONFIG_BOARD_LATE_INIT to set
the variables and then fdtfile and findfdt to make us of this. It is
now possible to do 'run findfdt' to have fdtfile be set to the value of
the dtb file to load for the board we are running on.
Signed-off-by: Tom Rini <trini@ti.com>
Add targets of am335x_evm_uart{1,2,3,4,5} to have serial input/output on
UART{1,2,3,4,5} for use with the Beaglebone RS232 cape, am335x_evm
daughterboard, and other custom configurations.
Modify target for am335x_evm to include SERIAL1 and CONS_INDEX=1
options in order to clarify UART selection requirements.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
Add the required config.mk logic for this SoC as well as the BOOT_DEVICE
define. Finally, enable the options on the am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
Fix usage of 'mmc rescan' by many configs. Proper use is
'mmc dev ${mmcdev}; mmc rescan' to set the mmc device and then rescan
the device. 'mmc rescan' itself does not take any arguments.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
A fast boot is important to the beaglebone, so save 2 seconds here by
decreasing bootdelay. This is still plenty time to break into the prompt,
I do that at least once a day.
Mount the rootfs RO by default, this is needed to make fsck succeed
without resorting to an initramfs.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
This patch adds support for networking in SPL on TI AM335x based
boards. Vendor Class Identifier used by SPL during BOOTP is
"AM335x U-Boot SPL".
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards. We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave
the NAND one in-place as we plan to replace it later in this series.
We use common/spl to avoid linker problems with respect to merging
constant strings in objects. Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.
Signed-off-by: Tom Rini <trini@ti.com>
CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present
in most ARM board config files.
IRQs are only enabled for 1 config, so remove the unused config options
for IRQ and FIQ stack size as well.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Make the lowlevel_init function that these platforms have which just
sets up the stack and calls a C function available to all armv7
platforms. As part of this we change some of the macros that are used
to be more clear. Previously (except for am335x evm) we had been
setting CONFIG_SYS_INIT_SP_ADDR to a series of new defines that are
equivalent to simply referencing NON_SECURE_SRAM_END. On am335x evm we
should have been doing this initially and do now.
Cc: Sricharan R <r.sricharan@ti.com>
Tested-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Rini <trini@ti.com>
Beaglebone uses SMSC PHY which works incorrectly with generic PHY
driver so enable SMSC PHY driver to fix networking problems on
Beaglebone.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This fixes the breakage with SPL on most OMAP boards after the GPIO
driver was moved.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
- Add default commands
- Add HUSH parser
- Make environment, malloc areas larger
- Add ATAGS and OF_LIBFDT
- Add defaults to boot ramdisk and MMC, use uEnv.txt
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds board-specific initialization for CPSW on
TI AM335X based boards. Tested on BeagleBone.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split board-specific part into separate patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
UART_RESET, UART_CLK_RUNNING_MASK, and UART_SMART_IDLE_EN
are defined inn evm.c but not used. Also removes unnecessary
include of serial.h
PHYS_DRAM_1_SIZE is defined in am335x_evm.h but never used.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
This patch is added to support SPL feature on AM335X
platform. In this patch, MMC1 is configured as boot
device for SPL and support for other devices will be
added in the next patch series.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
This patch add supports for mmc/sd driver on AM335X platform.
PLL and pinmux configurations for mmc/sd are configured in this
patch.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch is added to correct some of the AM335X config
parameters which were incorrect along with some cleanup
like removing unused code.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch is added to replace CONFIG_AM335X symbol
with CONFIG_AM333XX for AM33XX platforms.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Thomas Weber <weber@corscience.de>
This patch adds basic support for booting the board.
This patch adds support for the UART necessary to
get to the u-boot prompt.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
