After we switch to use BINMAN_SYMBOLS, there is no need to pad
the file size to 0x8000 and 0x4000. After we use BINMAN_SYMBOLS,
the u-boot-spl-ddr.bin shrink about 36KB with i.MX8MP-EVK.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8m[m,n,p]-venice
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
We are migrating to use binman symbols, the current names are
inconsistent across different boards, so unify them.
Also add `type = "blob-ext";`, since the new names are not valid binman
types.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8m[m,n,p]-venice
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
[Alper: Edit commit message]
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Set ARM clock to OD frequency 1.7Ghz, since we have set PMIC VDD_SOC
to Overdrive voltage 0.9V
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the DTSi file and DT header files for i.MX93 SoC
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since i.MX9 uses same DDR PHY with i.MX8M, split the DDRPHY to a common
directory under imx, then use dedicated ddr controller driver for each
iMX9 and iMX8M.
The DDRPHY registers are space compressed, so it needs conversion to
access the DDRPHY address. Introduce a common PHY address remap function
for both iMX8M and iMX9 for all PHY registers accessing.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement the DDR driver clock interfaces for set DDR rate and
bypass DDR PLL
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add bootaux command to support on-demand booting M33 from u-boot.
It kicks M33 via ATF by "bootaux 0x201e0000 0"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support on-demand booting M33 image from A core. SPL needs
to follow M33 kick up sequence to release M33 firstly,
then set M33 CPUWAIT signal. ATF will clear CPUWAIT to kick
M33 to run.
The prepare function also works around the M33 TCM ECC issue by
clean the TCM. Also enable sentinel handshake and WDOG1 clock
for M33 stop and reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add power init of MEDIAMIX, MLMIX and DDRMIX. And clear isolation
of MIPI DSI/CSI, USBPHY after the power up.
SPL should call the power init in its boot sequence before accessing
above three MIX and USB.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add GPIO registers structure for iMX93, so that we can enable lpgpio
driver
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX93 fuse can be accessed through FSB and s400-api. Add mapping tables
for i.MX93. The offset address of FSB accessing OTP shadow registers is
different between i.MX8ULP and i.MX93, so use macro to define the offset
address instead of hardcode.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the get chip revision methond to use S400 API, also record
other information like lifecycle and UID to global data.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add TRDC driver to iMX9. The TRDC init splits to two phases:
1. Early init phase will release TRDC from Sentinel and open write
permission to the memory where SPL image runs. Sentinel will set
the memory to RX only after ROM authentication for the OEM
closed part.
2. Init phase will configure TRDC to allow non-secure master to
access DDR. So the peripherals can work in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce Sentinel API ahab_release_m33_trout to make sure sentinel
release M33 trout and make sure M33 could boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support more RDC instances on i.MX93, update API to latest
definition.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since iMX9 uses S401 which shares the API with iMX8ULP. So move S400
MU driver and API to a common place and selected by CONFIG_IMX_SENTINEL
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX9 shares same ROM API with i.MX8ULP, so make the i.MX8ULP the function
prototype common and usable by i.MX9.
Also include mmc env functions that use ROM API.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add timer_init to update ARM arch timer with correct frequency
from system counter and enable system counter.
Signed-off-by: Jian Li <jian.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add clock API to support CCM root clock and LPCG setting
Set the CCM AUTHEN register to allow non-secure world to set
root clock and lpcg.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MN/P/ULP supports ROM API, they have almost same get_boot_device
implementation, so move to a common file. And when support i.MX9,
no need to include the other function copy.
Since sys_proto.h is included in imx_romapi.c, there will be build
warning for i.MX8M because wdog_regs not defined, so include imx-regs.h
in i.MX8M sys_proro.h
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For SoCs support ROM API, CONFIG_SPL_BOOTROM_SUPPORT is needed,
so use this macro to guard the code to avoid extend the list.
And drop the guard with structure definition, there is no need.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the default mapping of spl_boot_device to weak function of
spl_board_boot_device. So that every board of iMX7/8/8M can overwrite
this function to implement specific mapping.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The SPL SDP is configured as BOOT_DEVICE_BOARD, so when booting from
USB, change its type to BOOT_DEVICE_BOARD, so we can use SDP.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
All the SoCs use mach-imx has CONFIG_MACH_IMX selected, so
the macro could be the gate to build arch/arm/mach-imx to simplify
the rules.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With supporting timer_get_boot_us, we can profile boot up time with below
configs and function bootstage_mark_name().
CONFIG_BOOTSTAGE=y
CONFIG_BOOTSTAGE_REPORT=y
CONFIG_CMD_BOOTSTAGE=y
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Store a set of supported bitstream types in xilinx_desc structure.
It will be used to determine whether an FPGA image is able to be
loaded with a given driver.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-4-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
Mailbox driver might be need for Versal and other future platforms.
To remove the dependency, move struct zynqmp_ipi_msg to
zynqmp_firmware.h so that mailbox driver compiles for other platforms
easily.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220722084658.30995-5-ashok.reddy.soma@xilinx.com
With commit ce39ee28ec ("zynqmp: Do not place u-boot to reserved memory
location"), the function board_get_usable_ram_top() is allocating
MMU_SECTION_SIZE of about 2MB using lmb_alloc(). But we dont have this
much memory in case of mini U-Boot.
Keep these functions which use lmb under CONFIG_LMB so that they are
compiled and used only when LMB is enabled.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/75e52def75f573e554a6b177a78504c128cb0c4a.1657183534.git.michal.simek@amd.com
There are no references to CONFIG_SOC_DM355 / CONFIG_SOC_DM365 /
CONFIG_SOC_DM644X / CONFIG_SOC_DM646X and the files these Makefile lines
reference have already been dropped.
Signed-off-by: Tom Rini <trini@konsulko.com>
The ISW_ENTRY_ADDR symbol was used for OMAP devices in place of
SPL_TEXT_BASE. Keystone2 HS devices were not using it right either.
Remove ISW_ENTRY_ADDR and use SPL_TEXT_BASE directly.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Read the swrv.txt file from the TI Security Development Tools when
TI_SECURE_DEVICE is enabled. This allows us to set our software
revision in one place and have it used by all the tools that create
TI x509 boot certificates.
Signed-off-by: Andrew Davis <afd@ti.com>
The x509 certificate SWRV is currently hard-coded to 0. This need to be
updated to 1 for j721e 1.1, j7200 and am64x. It is don't care for other
k3 devices.
Added new config K3_X509_SWRV to k3. Default is set to 1.
Signed-off-by: Yogesh Siraswar <yogeshs@ti.com>
Reviewed-by: Dave Gerlach <d-gerlach@ti.com>
This isn't strictly needed as these firewalls should all be disabled on
GP, but it also doesn't hurt, so do this unconditionally to remove this
use of CONFIG_TI_SECURE_DEVICE.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
