This patch enable convert DM MMC for imx7d-pico board and variant.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing pico-pi bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing pico-imx7d boot code will
work unmodified.
When converting to DM_MMC it is necessary that SPL initializes eMMC
by itself, so move the original eMMC initialization from U-Boot
proper to SPL.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add support for lpuart1, lpuart2 and lpuart3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Remove duplicate function declarations from the SCFW API header file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This patch imports the Linux kernel base board imx7d-pico.dtsi,
pi board imx7d-pico-pi.dts and hobbit board imx7d-pico-hobbit.dts
from Linux v5.1-rc1.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Migrate Ethernet FEC to using driver model.
Drop PHY_MICREL_KSZ90X1 which slipped in from Apalis iMX6.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate USB to using driver model.
Add USBH_PEN GPIO regulator.
While at it also add alias e.g. as required for UMS.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate MMC to using driver model.
Migrate USDHC to using pinctrl.
While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The implicit fallback mechanism for searching the whole MDIO bus for at
least one PHY has been gone with the following commit b882005a18
("drivers/net/fec: phy_init: remove redundant logic"). This lead to the
Ethernet driver erroring out as follows:
Net: Could not get PHY for FEC0: addr -19
eth-1: fec@400d1000
Colibri VFxx # dhcp
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
No ethernet found.
Could not get PHY for FEC0: addr -19
Colibri VFxx #
This commit adds an explicit PHY node which makes it work again.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This commit enables the support for K&P's HSC|DDC imx53 based boards.
It was also necessary to provide device tree description for regulators
to avoid board specific code definition.
The GPIO pin description responsible for VBUS control has been moved from
"hog" group to usbh1 dedicated one.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This code has been ported from Linux kernel - tag v5.1-rc2.
The difference from the kernel is the removal of:
fsl,usbmisc = <&usbmisc 1>;
fsl,usbphy = <&usbphy1>;
properties, which are not needed for correct u-boot operation (as PHY
setup is done in ehci-mx5.c file itself).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
In this commit the esdhc3 controller is enabled as well as it is remaped
to mmc0 to not break legacy code.
The pinctrl setup (e.g. 0x1e4) is the same as one from in-board file
definition.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
with u-boot,dm-spl added for imx8qx-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
A mailbox command contains 1-u32 header + arguments. The "len" variable
only contains the length of the arguments, but not the 1-u32 header.
Include the length of header when checking the ring buffer space to
prevent off-by-one error.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
By enabling debug prints in malloc_simple, we can see that SPL for socfpga
gen5 does by far not need the 8 KiB malloc pool currently allocated for
SPL in pre-reloc phase.
On socfpga_socrates, 1304 bytes are currently used (and this increases by
~200 bytes only for the sdram/reset fixes in socfpga-next).
To prevent wasting precious SRAM space, let's reduce the initial heap used
for SPL to 2 KiB. This is still some hundred bytes more than currently
used. Also, the gen5 SPL enables stack and heap in DDR memory pretty
early. Only the initial uclass/dm parsing, serial console and DDR
initialization is done in the initial heap, so these 2 KiB should be
enough for all boards.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
This commit moves common config options used in all socfpga boards
to select/imply in Kconfig. This both cleans up the defconfig files
as well as makes future changes easier.
Options implied/defaulted for all sub-arches:
- SPL, SPL_DM, USE_TINY_PRINTF, NR_DRAM_BANKS
Options implied/defaulted for implied for A10 & gen5:
- FPGA_SOCFPGA, SYS_MALLOC_F_LEN, SYS_TEXT_BASE
Options implied/defaulted for gen5:
- SPL_STACK_R, SPL_SYS_MALLOC_SIMPLE, SPL_STACK_R_ADDR
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlzAfvkACgkQfxc6PpAI
reYu9AgAjaFmydXjE8DxkSB3rR7DHZFTs1erVKAAL2v+Tdf7LDmz+j6u1M3v55WY
6r54f/gZ1UX5TEmQgEAKLa7QvvRO/lNvSGQnLHhZhv2IVWo7uWCKAUPdQ6XVZnUK
zO5v+ucs9Ne4HxQJHMC509HUIIBbydiRvUm8W0SeBZy4kEyJDuub4L+rpARkXNks
IZfKuY+VS4FK73D4M9PIhoXSubZgVS4AEcapakU1DvEz0kjsN4wr4idGrp3lutPC
455imz83JBq2+mx1oxclOGedkIDzTCq+nWQAwSftMehrJpGrp7RLNo0v4QZZUf4V
LIXRqObIYse9yQLkYPpeBdePMc8/tQ==
=0NJ2
-----END PGP SIGNATURE-----
Merge tag 'pull-24apr19' of git://git.denx.de/u-boot-dm
Various minor sandbox iumprovements
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
Testing has shown that the current DM implementation of a platform /
board specific translation offset, as its needed for the SPL on MVEBU
platforms is buggy. The translation offset is confingured too late,
after the driver bind functions are run. This may result in incorrect
address translations. With the current implementation its not possible
to configure the offset earlier, as the DM code has not run at all.
This patch now removed the set_/get_translation_offset() calls and
moves the translation offset into the GD variable translation_offset.
This variable will get used when CONFIG_TRANSLATION_OFFSET is enabled.
This option is enabled only for MVEBU on ARM32 platforms, where its
currenty needed and configured in the SPL.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pierre Bourdon <delroth@gmail.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Tested-by: Pierre Bourdon <delroth@gmail.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Allocation routines were adjusted to ensure that the returned addresses
are a multiple of the page size, but the header code was not updated to
take account of this. These routines assume that the header size is the
same as the page size which is unlikely.
At present os_realloc() does not work correctly due to this bug. The only
user is the hostfs 'ls' command, and only if the directory contains a
unusually long filename, which likely explains why this bug was not
caught earlier.
Fix this by doing the calculations using the obtained page size.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if one of the initcalls fails on sandbox the address printing
is not help, e.g.:
initcall sequence 0000557678967c80 failed at call 00005576709dfe1f (err=-96)
This is because U-Boot gets relocated high into memory and the relocation
offset (gd->reloc_off) does not work correctly for sandbox.
Add support for finding the base address of the text region (at least on
Linux) and use that to set the relocation offset. This makes the output
better:
initcall sequence 0000560775957c80 failed at call 0000000000048134 (err=-96)
Then you use can use grep to see which init call failed, e.g.:
$ grep 0000000000048134 u-boot.map
stdio_add_devices
Of course another option is to run it with a debugger such as gdb:
$ gdb u-boot
...
(gdb) br initcall.h:41
Breakpoint 1 at 0x4db9d: initcall.h:41. (2 locations)
Note that two locations are reported, since this function is used in both
board_init_f() and board_init_r().
(gdb) r
Starting program: /tmp/b/sandbox/u-boot
[Thread debugging using libthread_db enabled]
Using host libthread_db library "/lib/x86_64-linux-gnu/libthread_db.so.1".
U-Boot 2018.09-00264-ge0c2ba9814-dirty (Sep 22 2018 - 12:21:46 -0600)
DRAM: 128 MiB
MMC:
Breakpoint 1, initcall_run_list (init_sequence=0x5555559619e0 <init_sequence_f>)
at /scratch/sglass/cosarm/src/third_party/u-boot/files/include/initcall.h:41
41 printf("initcall sequence %p failed at call %p (err=%d)\n",
(gdb) print *init_fnc_ptr
$1 = (const init_fnc_t) 0x55555559c114 <stdio_add_devices>
(gdb)
Signed-off-by: Simon Glass <sjg@chromium.org>
This fixes relaction isses with the PSCI_TABLE entries in
the psci_32_table and psci_64_table.
When using 32-bit adress pointers relocation was not being applied to
the tables, causing PSCI handlers to point to the un-relocated code
area. By using 64-bit data relocation is properly applied. The
handlers are thus in the "secure data" area, which is protected by
/memreserve/ in the FDT.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Add support for MediaTek MT8516 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The 'phy' reset of gmac device in kernel device tree is not generic
enough for u-boot to use, so we need to overwrite the 'resets' property
as needed. With this device tree fixup and poplar_defconfig changes,
Ethernet starts working on Poplar board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As U-boot stm32f clock driver doesn't support new
bindings for auxiliary clocks (clocks = <&rcc 1 ....>),
restore old bindings for usart1 to get console output.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Synchronize stm32h7 device tree with kernel v4.20.
U-boot DT files and pinctrl bindings are updated,
useless nodes are removed and gpio compatible added.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In order to prepare and ease future DT synchronization with kernel
DT, migrate all U-boot specific nodes/properties/addons to
U-boot DT files.
As sdmmc is not yet supported on kernel side, sdmmc nodes
are located in eval-u-boot and disco-u-boot DT files.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In order to prepare and ease future DT synchronization with kernel
DT, migrate all U-boot specific nodes/properties/addons to
U-boot DT files.
Migrate also DT nodes which are not yet available on kernel DT side
as ethernet, ltdc and qspi nodes.
Fix ethernet_mii pins and add missing qspi_pins for stm32746g-eval
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Import Linux 5.1-rc1 DT from 9e98c678c2d6 ("Linux 5.1-rc1") for the
meson-g12a-u200 board, the meson-g12a.dtsi and the corresponding bindings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for the Amlogic G12A SoC, which is a mix between the
new physical memory mapping of AXG and the functionnalities of
the previous Amlogic GXL/GXM SoCs.
To handle the internal ethernet PHY, the Amlogic G12A SoCs now
embeds a dedicated PLL to feed the internal PHY.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add basic support for the Amlogic G12A clock controller based on
the AXG driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
When fixing sandbox test for regmap_read_poll_timeout(), the
sandbox_timer_add_offset was introduced but only defined in sandbox code
thus generating warnings when used out of sandbox :
include/regmap.h:289:2: note: in expansion of macro 'regmap_read_poll_timeout_test'
regmap_read_poll_timeout_test(map, addr, val, cond, sleep_us, \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/meson_spifc.c:169:8: note: in expansion of macro 'regmap_read_poll_timeout'
ret = regmap_read_poll_timeout(spifc->regmap, REG_SLAVE, data,
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/meson_spifc.c: In function 'meson_spifc_txrx':
include/regmap.h:277:4: warning: implicit declaration of function 'sandbox_timer_add_offset' [-Wimplicit-function-declaration]
This fix adds a timer_test_add_offset() only defined in sandbox, and
renames the previous sandbox_timer_add_offset() to it.
Cc: Simon Glass <sjg@chromium.org>
Reported-by: Tom Rini <trini@konsulko.com>
Fixes: df9cf1cc08 ("test: dm: regmap: Fix the long test delay")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Current relocation code is limited to 21bit PC-relative addressing
which might not be enough for bigger code sizes. The following patch
increases the addressing to 32bit PC-relative. This feature is
specially interesting if U-Boot is build without optimiation (-O0) as
the text section is increased significativelly.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
HVC call makes use of 6 mandatory arguments rather than 7 in the same way
as SMC calls. The 7th argument is optional (Client ID) for both HVC and
SMC but is implemented as 16-bit parameter and register R7 or W7. The aim
of this patch is just fix compilation error due to an invalid asm code in
the HVC call so that's why the 7th argument is removed.
The issue does not report any error in a normal build as hvc_call is not
used at all and is optimized by the compiler. Using -O0 triggers the
error so the patch is intended to fix issues on a ongoing effor to build
U-Boot with -O0.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
When PSCI is enabled, we are expecting U-Boot which now act
as EL3 software will handle all the PSCI calls. We won't need
fwcall as no further HVC or SMC are needed.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Allow PSCI layer to handle any SiP service functions added by
platform vendors. PSCI layer will look for SiP service function
in the SiP function table located in '._secure_svc_tbl_entries'
section if the SMC function identifier is not found in the PSCI
standard functions table. Use DECLARE_SECURE_SVC macro to declare
and add platform specific SiP service function.
This new section '._secure_svc_tbl_entries' is located next to
'._secure.text' section. Refer to arch/arm/cpu/armv8/u-boot.lds.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcvW07AAoJEB6zHgIOrC/Iu4QH/1REDOTrsZPydd2yD/O81vPs
RiLC8wP2J4UmqtMcNTLyvxlYwrzqoR5J6SYdyBNU/+cLEp/gdzEI+rjsfSV2uRX1
Qb4Pk2FiI503JVjegxsbJqzASfiEP7rIg3HM5431xbhYH22MW2FH6le6yrtNxjBh
m1WFjQYX1bpbGb6zue8TgyLIeN1IqWuqnH9kUHixUEan+xrpEhN239LDFjdvGbvC
BvYyMtDddmMt4YDzNjgX36us993kylGZp6JijR3zgUao7I/JGVZAJrxw8MHDTnVy
UKv3VI9F5bGLSvzqTVL2MFU6XtJW26v+niGLhGzlUhb3TTKrdKOicm3VF7tO+JU=
=MamK
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.07-b' of git://git.denx.de/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2019.07 cycle
The DK1 and DK2 boards use the USB Type-C controller STUSB1600.
This patch updates:
- the device tree to add the I2C node in the DT
- the board stm32mp1 to probe this I2C device and use this controller
to check cable detection.
- the DWC2 driver to support a new dt property
"u-boot,force-b-session-valid" which forces B session and
device mode; it is a workaround because the VBUS sensing and
ID detection isn't available with stusb1600.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Use the DWC2 device driver with DM_USB_GADGET support and
cleanup the USB support in STM32MP1 board.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The SAMA5D2 ICP Board features the SAMA5D27 SoC,
together with QSPI Flash, Wilc3000 wireless device and
EtherCat support.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Merge qspi dts node from Linux.
Commit 0cb140d07fc75fb (arm64: dts: stratix10: Add QSPI support for Stratix10)
Add -u-boot.dtsi files for non Linux dts properties and
update properties for Uboot.
- add u-boot,dm-pre-reloc
- add alias for spi0
- change compatible for flash
- support quad read and quad write
- change maximum frequency to 100MHz
Tested on Stratix 10 SoC devkit.
SOCFPGA_STRATIX10 # sf probe 0:0
SF: Detected mt25qu02g with page size 256 Bytes, erase size 64 KiB, total 256 MiB
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Scrub memory content if ECC is enabled and it is not
from warm reset boot.
Enable icache and dcache before scrub memory
and use "DC ZVA" instruction to clear memory
to zeros. This instruction writes a cache line
at a time and it can prevent false ECC error
trigger if write cache line partially.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
The stratix10 socdk ships with 4GB of memory. Modify the
device tree to represent this. Note that to access 4GB of
memory in Stratix 10, due to the IO space from 2GB to 4GB,
we use the fact that the DDR controller ignores upper address
bits outside of the configured DRAM's size. This means that
, the 4GB DRAM is mapped to memory every 4GB.
For an 8GB memory, you can either live with the 2GB IO space,
and loose access to that memory from the processor, or use
the same trick:
Loose 2GB of memory:
memory {
device_type = "memory";
/* 8GB */
/* first 2GB */
reg = <0 0x00000000 0 0x80000000>,
/* last 4GB */
<1 0x00000000 1 0x00000000>;
u-boot,dm-pre-reloc;
};
or to map it all:
memory {
device_type = "memory";
/* 8GB */
/* first 2GB */
reg = <0 0x00000000 0 0x80000000>,
/* next 6GB */
<2 0x80000000 1 0x80000000>;
u-boot,dm-pre-reloc;
};
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Move SDRAM size check to SDRAM driver. sdram_calculate_size()
is called in SDRAM initialization already, avoid calling
twice in size check function.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
This commit removes ad-hoc reset handling for peripheral resets from SPL
for socfpga gen5.
This is done because as U-Boot drivers support reset handling by now.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
To clean up reset handling for socfpga gen5, port the DDR driver to DM
using UCLASS_RAM and implement proper reset handling.
This gets us rid of one ad-hoc call to socfpga_per_reset().
The gen5 driver is implemented in 2 distinct files. One of it (containing
the calibration training) is not touched much and is kept at using
hard coded addresses since the code grows even more otherwise.
SPL is changed from calling hard into the DDR driver code to just
probing UCLASS_RESET and UCLASS_RAM. It is happy after finding a RAM
driver after that.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The SPL for socfpga gen5 currently takes all peripherals out of reset
unconditionally. To implement proper reset handling for peripherals,
the reset node has to be provided with the SPL dts.
In preparation to move the DDR driver to DM, the sdr node is required
in SPL, too.
This patch adds "u-boot,dm-pre-reloc" to U-Boot specific dtsi addon
files so that the reset manager and SDR driver correctly probe in SPL.
It centralizes these settings into a common file since in contrast to
boot-type specific nodes, "soc", "rst" and "sdr" are always needed.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This is again a sync to linux-next + pending patches in Dinh's tree at
commit 1c909b2dfe6a ("ARM: dts: socfpga: update more missing reset
properties")'
It adds missing peripheral reset properties to socfpga.dtsi and removes
U-Boot specific leftovers from socfpga_cyclone5_socrates.dts.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAly262oACgkQykllyylKDCH44gCbBnuxUH6ZF0B7Leuee4te7C59
LmUAn14/bbtMt17zkMSADCjY9yGWF4au
=mWrW
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.07' of git://git.denx.de/u-boot-microblaze
Xilinx/FPGA changes for v2019.07
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
- Enable DM_MMC if MMC defined
- Enable DM_SCSI if SCSI defined
globally through Allwinner platform, the effected SoC families
and boards will make use of MMC and SCSI subsystems in driver-model.
Tested DM_MMC in one board from A64, H6, H5, H3, R40, A83T, A20, A10
SoCs.
Tested-by: Pablo Sebastián Greco <pgreco@centosproject.org> # BPI-M2-Ultra
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable ahci node for BPI-M2-Berry, this would require since
we have DM_SCSI enabled on the respective SoC.
Unable to sync the same node from Linux, since the similar change
is still in Linux ML.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable ahci node for a20-wits-pro-a20-dkt, this would require since
we have DM_SCSI enabled on the respective SoC.
Right now, ahci enabled in -u-boot.dtsi and will remove once same
supported by Linux.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable ahci node for sun7i-a20-m5.dts, this would require since
we have DM_SCSI enabled on the respective SoC.
No need to send patch to Linux for this change, since this
dts is U-Boot specific.
Cc: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync sun7i-a20 dts(i) files from Linux 5.1-rc2
Linux commit details about the sun7i-a20* sync:
"ARM: dts: sun7i: bananapi: Add GPIO banks regulators"
(sha1: 09c6572290f018d73ec2e812e28bada34d41815f)
Here are U-Boot specific dts changes.
- s/uart0_pins_a/uart0_pb_pins for
sun7i-a20-ainol-aw1.dts
sun7i-a20-m5.dts
sun7i-a20-primo73.dts
sun7i-a20-yones-toptech-bd1078.dts
sunxi-itead-core-common.dtsi
- s/gmac_pins_mii_a/gmac_rgmii_pins for
sun7i-a20-m5.dts
- drop i2c0, i2c1 pins from
sunxi-itead-core-common.dtsi
- drop mmc0 pins from
sun7i-a20-primo73.dts
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync sun8i-r40 dts(i) files from Linux 5.1-rc2
Linux commit details about the sun8i-r40* sync:
"ARM: dts: sun8i: r40: bananapi-m2-ultra: Add Bluetooth device node"
(sha1: 1e5f1db4ccd8348a21da55bff82f4263000879ef)
Linux commit details about the sun8i-v40* sync:
"ARM: dts: sunxi: Fix I2C bus warnings"
(sha1: 0729b4af5753b65aa031f58c435da53dbbf56d19)
Cc: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
A missing CONFIG_ prefix while checking for this Kconfig variable makes the
check always fail. Fix it. While there also switch from the '#if defined'
form to the '#ifdef' form as the other checks in this function.
Fixes: 35e2b92344 ("arm64: zynqmp: Fix logic around CONFIG_ZYNQ_SDHCI")
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define a label for flash node so that it can be
referenced easily as required.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
spi-flash compatible string is needed for reading tx and rx bus
widths, hence add this compatible string to flash node.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
add labels to rtc, pinctrl and watchdog node.
This makes it possible to reference the nodes
from board dts files.
Signed-off-by: Heiko Schocher <hs@denx.de>
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
-----BEGIN PGP SIGNATURE-----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=KLsH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190415' of git://git.denx.de/u-boot-imx
Move to DM
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
In the aarch64 crash dump information about the loaded EFI images is added.
In README.uefi the development target is for the UEFI subsystem is
described as "Embedded Base Boot Requirements (EBBR) Specification"
compliance.
Several bug fixes are supplied.
-----BEGIN PGP SIGNATURE-----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=QdJl
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc1-2' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc1 (2)
In the aarch64 crash dump information about the loaded EFI images is added.
In README.uefi the development target is for the UEFI subsystem is
described as "Embedded Base Boot Requirements (EBBR) Specification"
compliance.
Several bug fixes are supplied.
Usually the Linux dts changes were synced in specific tags in Allwinner,
to keep track for whats been synced so-far and plan for future syncs.
But this patch sync sun50i-h6* dts(i) files from Linux w/o any specific
tag since these dts(i) changes are required for new H6 boards support.
Linux commit details about the sun50i-h6* sync:
"arm64: dts: allwinner: h6: move MMC pinctrl to dtsi"
(sha1: 6ba2e45d57afdfd982d12f168edd6a79a65075d8)
Linux commit details about the sun8i-tcon-top.h sync:
"dt-bindings: display: sunxi-drm: Add TCON TOP description"
(sha1: 59a9c39544cd1e5952c2a33028d71aa8180648f8)
Part of the sync initiated by 'Clément Péron'.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Fix broken build:
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix broken build:
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add support for Vybrid's UART2 (Colibri UART_B).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Update device tree in preparation of further driver model migration:
Ethernet FEC, ESDHC aka MMC/SD card, I2C, NFC aka NAND flash controller,
USBH_PEN GPIO regulator.
Add iomux resp. pinctrl entries to be removed from proprietary platform
data: DSPI, ESDHC, FEC, I2C, NFC, UART, USBH_PEN GPIO.
Introduce a U-Boot specific device tree with some required
u-boot,dm-pre-reloc properties: soc, aips0, pinctrl_ddr and uart0 incl.
pinctrl.
While at it also update the MAINTAINERS file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Allow using bootaux also on VF610 aka Vybrid.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The DDR memory controller include file for the Vybrid uses
iomux_v3_cfg_t without actually including iomux-vf610.h.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Extend the driver to build with DM_VIDEO enabled. DTS files
must additionally include 'u-boot,dm-pre-reloc' property in
soc and ipu nodes to enable driver binding to ipu device.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
... as preparation for additional driver model coonversions.
We use CONFIG_OF_EMBED here to keep u-boot.imx as final binary name. So we
maintain compatibility with the original TBS u-boot and available HOWTOs
for u-boot updates.
Signed-off-by: Soeren Moch <smoch@web.de>
This code allows reusing the default u-boot as in the late board init, the
default envs are restored and proper recovery scripts executed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit brings a separate file in which the U-Boot specific
properties (like 'dm-pre-reloc') are provided.
Such approach allows easy sync with upstream Linux kernel in the
future.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This commit provides update and renames the bk4r1.dts to vf610-bk4r1.dts
file with more on SoC HW description.
The pcm052.dts has been renamed to vf610-pcm052.dts as well.
Moreover, a new vf610-pcm052.drsi file has been introduced
to reuse the common code between devices based on Phytec's
pcm052 modules.
Ported from Linux kernel - v4.20 (tag)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch allows moving vf610 based boards to a device tree and model.
Ported from Linux kernel - v4.20 (tag)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The proposed way of reading fused MAC in the imx_get_mac_from_fuse() may
be different for other boards.
This commit defines the imx_get_mac_from_fuse() as a weak function to allow
board file overriding it with customized function.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Provide function to enable I2C clocks for vf610 - in the generic code.
This function overrides the default weak function implementation (which
only returns 1).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This patch provides definitions necessary for VF610 DDR pad configurations.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
pinctrl race-condition fix
various other fixes in sandbox, sound, mkimage, etc.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlyxBfcACgkQfxc6PpAI
reYtsgf8DSi0h6bNmoPGA8q/aRTQii2x6TheT+AonvND4Kt5ycyw5Otjn3n7O13G
ubDvBn3Ix5znRaj6nSip7zO1M59dNB19Qk5i+ad21w3rx2V8HTWcLYMwUmC2DPZU
qMaOpIeEWYKuCDFRhpw/b6yF1rtq4lMxWTrSlB+ewntmrKV+Ymk0UWYSCfNMmZ8F
cLSd/wFWoTxysZLT4t/5jbNIPU8XaO0hYH0C9Y/tsK80bCpdjkTMNQuO7/qlgUb9
E7BCf1HXuMqWTZuqub9hu1y24PYufNSHziK1R+lNqm+yW3MxJGihP5OsCfVoHDgu
FU+QIKeBo64R3eH1VSrAh8pLp143bg==
=4/BU
-----END PGP SIGNATURE-----
Merge tag 'pull-12apr19' of git://git.denx.de/u-boot-dm
fdtdec tests and improvements for carve-outs
pinctrl race-condition fix
various other fixes in sandbox, sound, mkimage, etc.
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
-----BEGIN PGP SIGNATURE-----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=NrV8
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-04-12' of git://git.denx.de/u-boot-mips
- mt76xx: add USB support, small fixes
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
If an exception occurs in a UEFI loaded image we need the start address of
the image to determine the relocation offset.
This patch adds the necessary lines after the registers in the crash dump
for armv8. A possible output would be:
UEFI image [0x00000000bffe6000:0x00000000bffe631f] pc=0x138 '/\snp.efi'
With the offset 0x138 we can now find the relevant instruction in the
disassembled 'snp.efi' binary.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- Misc dts files sync'ed with Linux version (Chris)
- Orion watchdog fix (Chris)
- kwbimage changed to also support Marvell bin_hdr binary (Chris)
- Add DM support to enable CONFIG_BLK for sata_mv (Stefan)
- Enable BLK on multiple platforms (Stefan)
- Misc minor fixes to AXP theadorable board (Stefan)
- Correct logic for DM_SCSI + unconverted drivers check (stefan)
- Misc changes to kirkwood to enable DM_USB here (Chris)
- Change ahci_mvebu to enable usage on A38x (Baruch)
- Update the kirkwood entry in git-mailrc (Baruch)
- Misc minor improvements (turris, documentation) (Baruch)
- Enhance sata_mv to support Kirkwood as well (Michael)
- Add wdt command (Michael)
- Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG
board support (Chris)
Add ethernet nodes for ServalT SoCs family. Currently there is only one
pcb(pcb116) in this family.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Add network driver for Microsemi Ethernet switch.
It is present on ServalT SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add ethernet nodes for Jaguar2 SoCs family. There are 3 pcb in this
family: pcb110, pcb111 and pcb112.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
As no gpio.h is defined for this architecture, to avoid
a compilation failure, do not include <asm/arch/gpio.h>
for arch bcm63158.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch bcm6858.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Enable the gpio controllers in the device tree
of the board bcm968380gerg.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add gpio controllers in bcm6838 device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
QCA9563 is CPU used on AP152 board :
Clock speed : 750 MHz ,
Arch : Mips 74Kc,
Eth : SGMII interface,
MIMO config : 3 * 3 450M,
2 * USB 2.0,
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Changes for v2:
- coding style cleanup
- remove ununsed flash chip in defconfig
- enable automatic icache / dcache size in defconfig
Changes for v3:
- add detailed information for qca956x in commit message
Changes for v4:
- remove pre-configured network settings in ap152.h
Changes for v5:
- coding style cleanup
See details in chapter 8.6.2 and 8.6.4 (page 140-141) of qca9563 datasheet,
NFRAC[17:0]
So the mask of [17:5] is 0x1fff not 0x3fff.
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Changes for v2-v3:
- add more information for this commit
Changes for v4-v5:
- coding style cleanup
Remove the function boot_reloc_ramdisk in the file arch/mips/lib/bootm
because it is relocating again the ramdisk. The function do_bootm_states()
already relocates the ramdisk even if it is a legacy uImage or a FIT image.
The relocation in the function do_bootm_states() was introduce in the
commit c2e7e72bb9 ("bootm: relocate ramdisk
if CONFIG_SYS_BOOT_RAMDISK_HIGH set")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
