Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.
Also drop the prototype for video_get_info_str() which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Commit 5bc4cd05d7 ("sunxi: move non-essential code out of s_init()")
moved the call to eth_init_board() from s_init() into board_init_f().
This means it's now only called from the SPL, which makes sense for
most of the other moved low-level functions. However the GMAC pinmux and
clock setup in eth_init_board() was not happy about that, so it broke
the sun7i GMAC.
Since Ethernet is of no use in the SPL anyway, just move the call into
board_init(), which is only run in U-Boot proper.
This fixes Ethernet operation for the A20 SoCs, which broke in
v2022.04-rc1, with the above mentioned commit.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Petr Štetiar <ynezz@true.cz> [a20-olinuxino-lime2]
Add following two new PCI class codes defines into pci_ids.h include file:
PCI_CLASS_BRIDGE_PCI_NORMAL
PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE
And use these defines in all U-Boot code for describing PCI class codes for
normal and subtractive PCI bridges.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_LCD_INFO
CONFIG_LCD_LOGO
CONFIG_LCD_INFO_BELOW_LOGO
CONFIG_LCD_IN_PSRAM
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ATMEL_LCD
CONFIG_ATMEL_LCD_BGR555
CONFIG_ATMEL_LCD_RGB565
CONFIG_GURNARD_SPLASH
Signed-off-by: Tom Rini <trini@konsulko.com>
This variable is used once and is noted as board-specific. Use the
value directly with a comment.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This symbol is used only once, and in comparison with an unset symbol,
so drop it.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91SAM9G10EK
CONFIG_AT91SAM9261EK
CONFIG_AT91SAM9G10
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91SAM9G20EK
CONFIG_AT91SAM9260EK
CONFIG_AT91SAM9G20EK_2MMC
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
A small number of i.MX6/7 and vf610 boards have not enabled DM_ETH yet.
Given the state of the rest of the platform, enable DM_ETH.
Cc: Alison Wang <alison.wang@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Richard Hu <richard.hu@technexion.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for Kevin, an RK3399-based convertible chromebook that is
very similar to Bob. This patch is mostly based on existing support for
Bob, with only minor changes for Kevin-specific things.
Unlike other Gru boards, coreboot sets Kevin's center logic to 925 mV,
so adjust it here in the dts as well. The rk3399-gru-kevin devicetree
has an unknown event code reference which has to be defined, set it
to the Linux counterpart. The new defconfig is copied from Bob with the
diffconfig:
DEFAULT_DEVICE_TREE "rk3399-gru-bob" -> "rk3399-gru-kevin"
DEFAULT_FDT_FILE "rockchip/rk3399-gru-bob.dtb" -> "rockchip/rk3399-gru-kevin.dtb"
VIDEO_ROCKCHIP_MAX_XRES 1280 -> 2400
VIDEO_ROCKCHIP_MAX_YRES 800 -> 1600
+TARGET_CHROMEBOOK_KEVIN y
With this Kevin can boot from SPI flash to a usable U-Boot prompt on the
display with the keyboard working, but cannot boot into Linux for
unknown reasons.
eMMC starts in a working state but fails to re-init, microSD card works
but at a lower-than-expected speed, USB works but causes a hang on
de-init. There are known workarounds to solve eMMC and USB issues.
Cc: Marty E. Plummer <hanetzer@startmail.com>
Cc: Simon Glass <sjg@chromium.org>
[Alper: commit message, resync config with Bob, update MAINTAINERS,
add to Rockchip doc, add Kconfig help message, set regulator]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The RK3399 SoC needs to know the voltage value provided by some
regulators, which is done by setting relevant register bits. Configure
these the way other RK3399 boards do, but with the same values as are
set in the equivalent code in coreboot.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYjIBkgAKCRDKSWXLKUoM
IYUwAKCYRBxb59BFq4MRvTbNcRZ7H4oGIQCfVUl3x9KZ7nFZaYAaBXFBxwna+PE=
=irCR
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.07-rc1
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
stm32mp1 bsec: Add permanent lock write support
stm32mp1 bsec: Add dev in function description
cmd_stboard: Update test on misc_read() result
video: fix the check of return value of clk_set_rate in stm32_ltdc
DT: Alignment with kernel v5.17 for stm32mp15
DT: Add USB OTG pinctrl and regulator in SPL for DHCOR
DT: Move vdd_io extras into Avenger96 extras
DT: Add DFU support for DHCOM recovery
ram: stm32mp1: Unconditionally enable ASR
psci: Implement PSCI system suspend and DRAM SSR for stm32mp
-----BEGIN PGP SIGNATURE-----
iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmIwUdYcHHBhdHJpY2Uu
Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/pj/FEAClzm1xFrw0oxsIGf9J
Ukyd66yIWiC2rjrxnOh7dtE3toHVVr9+GtM3RohS913BFoVTzlwUlfK75LBrxwWg
Qyp6P8BUWIf8P3Q/x+VcLXuHr/Q+o7prROxclumTEnhzcDhlp/Q6zwXcqXIH77cn
uOxjK5BE1Mt1KI8Fz94EqntoOars5UvxPpye7pahAlGzdZ1PDB1YR8dE5ZjCRG3Q
jNx6I0EZBfjQTHBEtLUSIUGykCDWGJwfbPEgZPa1ePdkgOvDrKQDd0ES89lhjU95
SQG9GFChug+rvXh9i4dxPBK1TGsvCjlZCbrmDGZGLnCfwkHsIzv+ajTpyBzXH5xA
t3XWK0vIaCOpAs1CcRrLjVUA6Paz8qkbTyoGGezvWtRwZ7wV35nI0n/g+R9NM1jC
GR5rrH6yIqrhj6TCneckkIVuiGRRVAXrr43a0BazzzBLSw8N9R8QB8BiM+p4hr8C
anakyfZSN2Y8dBp4EAfzyCV2hOPaUNdaUyzcUIxxDu8eQAqZR0nzjXY6vuV8g702
jr8Q/J2nc520INo6nwHKyOTD4+xAOK81cjQ0LTswTkx67afPmtAXH9EjZLeQ/u9P
ReKCnf/krS/0BhN2WoYXuAl7YQmXyLilrcsA9pXg2fc6lLNw48ZKz0eDZzX549kM
mP8xVQ+qQAiCcIxd+ijwuSSmTA==
=H4+P
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220315' of https://source.denx.de/u-boot/custodians/u-boot-stm
mtd: add NAND write protect support to stm32_fmc2_nand
stm32mp1 bsec: Add permanent lock write support
stm32mp1 bsec: Add dev in function description
cmd_stboard: Update test on misc_read() result
video: fix the check of return value of clk_set_rate in stm32_ltdc
DT: Alignment with kernel v5.17 for stm32mp15
DT: Add USB OTG pinctrl and regulator in SPL for DHCOR
DT: Move vdd_io extras into Avenger96 extras
DT: Add DFU support for DHCOM recovery
ram: stm32mp1: Unconditionally enable ASR
psci: Implement PSCI system suspend and DRAM SSR for stm32mp
"kendryte" is the marketing name for the K210 RISC-V SoC produced by
Canaan Inc. Rather than "kendryte,k210", use the usual "canaan,k210"
vendor,SoC compatibility string format in the device tree files and
use the SoC name for file names.
With these changes, the device tree files are more in sync with the
Linux kernel DTS and drivers, making uboot device tree usable by the
kernel.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Update management of misc_read/misc_write, which now returns length of
data after the commit 8729b1ae2c ("misc: Update read() and write()
methods to return bytes xfered"): raise a error when the result is not
the expected length.
Fixes: 658fde8a36 ("board: stm32mp1: stboard: lock the OTP after programming")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
- convert Nokia RX-51 to CONFIG_DM_VIDEO
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYi+zvw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXIReAJ9JS06uOjNFmOBdfpsOI2jnVdWABQCbB8nvUh19
jbftZtj+18fhFuNb1r4=
=3vpL
-----END PGP SIGNATURE-----
Merge tag 'video-20220314' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix display of the u-boot logo on Apple devices
- convert Nokia RX-51 to CONFIG_DM_VIDEO
Initialization and power on operations of links have been moved under the
link device in the Sierra SerDes driver. Also, the UCLASS of
sierra_phy_provider has been changed to UCLASS_MISC.
Therefore, fix the probing of SerDes0 instance accordingly.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Georgi Vlaev <g-vlaev@ti.com>
This adds platform code and the device tree for the Phytium Pomelo Board.
The initial support comprises the UART and the PCIE.
Signed-off-by: weichangzheng <nicholas_zheng@outlook.com>
With updated device trees now supporting pinmuxing for USB,
ethernet, MMC, and other peripherals necessary to start MLO
and U-Boot, the hard-coded pinmux options can be removed since
they are now handed by DM and only muxed when the respective
peripheral needs it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
With recent fixes to USB pinmuxing in the device trees, there
is no need to hard-code the pinmuxing in this table. It is
all handled in DM now.
Signed-off-by: Adam Ford <aford173@gmail.com>
The ethernet controller is DM compliant, and the device tree
defines it. There is no need to manually handle pulling
the ethernet out of reset.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
The PMIC enables power to the MMC card by default, but depending
on the state it was left when restarted, it's possible the MMC
may be powered down.
This patch patch explicitly tells the twl4030 to power the MMC.
Based on commits [1][2].
[1] 64fd2d2614
[2] 27b6534491
Signed-off-by: Romain Naour <romain.naour@gmail.com>
With DM_MMC working for both SPL and U-Boot, this patch removes
the legacy style of initializing the MMC driver.
Based on omap3_logic: 42140dd096.
Signed-off-by: Romain Naour <romain.naour@gmail.com>
This hook can be implmented using events, for the three boards that
actually use it.
Add the event type and event handlers. Drop CONFIG_MISC_INIT_F since we
can just use CONFIG_EVENT to control this. Since sandbox always enables
CONFIG_EVENT, we can drop the defconfig lines there too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently we only support to load the environment from raw MMC or FAT
locations on Allwinner boards. With the advent of SPI flash we probably
also want to support using the environment there, so we need to become
a bit more flexible.
Change the environment priority function to take the boot source into
account. When booted from eMMC or SD card, we use FAT or MMC, if
configured, as before.
If we are booted from SPI flash, we try to use the environment from
there, if possible. The same is true for NAND flash booting, although
this is somewhat theoretical right now (as untested).
This way we can use the same image for SD and SPI flash booting, which
allows us to simply copy a booted image from SD card to the SPI flash,
for instance.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Mechanically convert video_hw_init() function to UCLASS_VIDEO probe
callback and replace CONFIG_CFB_CONSOLE by CONFIG_DM_VIDEO.
As framebuffer base address is setup by the bootloader which loads U-Boot,
set plat->base to that fixed framebuffer address.
This change was tested in qemu n900 machine and is working fine.
What does not work is CONFIG_VIDEO_LOGO, seems to be buggy.
Signed-off-by: Pali Rohár <pali@kernel.org>
Since commit 5d94cbd1dc ("scripts: Makefile.lib: generate
dsdt_generated.c instead of dsdt.c"), the file generated
is named dsdt_generated.c instead of dsdt.c.
So all files .gitignore referencing dsdt.c should be
upated with dsdt_generated.c.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This add the initial support of the broadcom reference
board bcm96753ref with a bcm6753 SoC.
This board has 1 GB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Add support to read MAC addresses from mac address multirecord.
Check if multi record is found, then jump to mac address multirecord by
comparing the record type field. If it matches mac address
multirecord(0xD2), then copy mac addresses.
Copy these read MAC address in xilinx_read_eeprom_fru so that they are
updated to eth*addr in board_late_init_xilinx().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/18f31bc528820934854ea5fd9dc581778fc1e40c.1645624855.git.michal.simek@xilinx.com
In board_late_init_xilinx() eth*addr are updated from the values read from
eeprom. Ideally the MAC addresses are updated sequencially. So if any
MAC address is invalid, it means there are no further valid values.
So optimise this logic by replacing continue with break.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/efef0d07add5d5777396ea111ad75411dc402db3.1645624855.git.michal.simek@xilinx.com
fru_checksum function is simply adding all the bytes and returning the
sum. If the data passed to this function is all zero's then it will
return 0, and the functions calling this api will assume that checksum
is correct. Ideally this is not good. Fix this by returning error if all
the data is 0's.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/ac0366fe55c60a818a3f9ed33d96826c817d5520.1645624855.git.michal.simek@xilinx.com
We only want to call do_board_detect() if CONFIG_TI_I2C_BOARD_DETECT
is set. Same as done for am64.
This makes it possible to add a custom am65 based board design to
U-Boot that does not use this board detection mechanism.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Commit 369e532691 ("ddr: marvell: a38x: allow board specific ODT
configuration") added the odt_config member to struct
mv_ddr_topology_map ahead of the clk_enable and ck_delay members. This
means that any boards that configured either of clk_enable or ck_delay
needed to have their board topology updated. This affects the x530 and
clearfog boards. Other A38x boards don't touch any of the trailing
members of mv_ddr_topology_map so don't need updating.
Fixes: 369e532691 ("ddr: marvell: a38x: allow board specific ODT configuration")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
The branch_if_master macro jumps to a label if the CPU is the "master"
core, which we define as having all affinity levels set to 0. To check
for this condition, we need to mask off some bits from the MPIDR
register, then compare the remaining register value against zero.
The implementation of this was slighly broken (it preserved the upper
RES0 bits), overly complicated and hard to understand, especially since
it lacked comments. The same was true for the very similar
branch_if_slave macro.
Use a much shorter assembly sequence for those checks, use the same
masking for both macros (just negate the final branch), and put some
comments on them, to make it clear what the code does.
This allows to drop the second temporary register for branch_if_master,
so we adjust all call sites as well.
Also use the opportunity to remove a misleading comment: the macro
works fine on SoCs with multiple clusters. Judging by the commit
message, the original problem with the Juno SoC stems from the fact that
the master CPU *can* be configured to be from cluster 1, so the
assumption that the master CPU has all affinity values set to 0 does not
hold there. But this is already mentioned above in a comment, so remove
the extra comment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch scans the cmdline from the Samsung SBL (second stage
bootloader) and stores the parameters board_id=N and lcdtype=N
in order to augment the DTB for different board and LCD types.
We then add a custom ft_board_setup() callback that will inspect
the DTB and patch it using the stored LCD type. At this point
we know which product we are dealing with, so using the passed
board_id we can also print the board variant for diagnostics.
We patch the Codina, Skomer and Kyle DTBs to use the right
LCD type as passed in lcdtype from the SBL.
This also creates an infrastructure for handling any other
Samsung U8500 board variants that may need a slightly augmented
DTB.
Cc: Markuss Broks <markuss.broks@gmail.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To make sure we get a working console as soon as possible in the SPL the
UART pins require to be configured earlier. This is especially
true for the pins of UART3, since the PDU001 board uses this UART for
the console by default.
Signed-off-by: Felix Brack <fb@ltec.ch>
The changes from commit 0dba45864b ("arm: Init the debug UART")
prevent the early debug UART from being initialized correctly.
To fix this we not just configure the pin multiplexer but add setting up
early clocks.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This board has an internal watchdog which supervises the board startup.
Although, the initial state of the watchdog is configurable, it is
enabled by default. In board_late_init(), which means almost everything
worked as expected, disable the watchdog.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Most of the time it is very useful to have the version of the board
management controller. Now that we have a driver, print it during
startup.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The current console output is:
DRAM: 4 GiB
DDR 4 GiB (DDR3, 32-bit, CL=11, ECC on)
The size is printed twice and we can save one line of console output if
we join both lines. The new output is as follows:
DRAM: 4 GiB (DDR3, 32-bit, CL=11, ECC on)
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is a conflict between the static file
lib/acpi/dsdt.c and the file dsdt.c generated
dynamicaly by scripts/Makefile.lib. When a
mrproper is done, the static file dsdt.c is
removed. If a build with acpi enabled is
launched after, the following error is raised:
CC lib/acpi/acpi_table.o
make[2]: *** No rule to make target 'lib/acpi/dsdt.asl', needed by 'lib/acpi/dsdt.c'. Stop.
scripts/Makefile.build:394: recipe for target 'lib/acpi' failed
To avoid such error, the generated file is named
dsdt_generated.c instead of dstdt.c.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
The commit 0dba45864b ("arm: Init the debug UART") calls
debug_uart_init() from crt0.S but it won't work because SOC is not
configured yet. That's why create board_debug_uart_init() which calls
psu_init() via new psu_uboot_init() earlier before the first access to UART
in SPL. In full U-Boot call psu_uboot_init() only when
CONFIG_ZYNQMP_PSU_INIT_ENABLED is enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/878dc2daaa8685346f889989fbfb98b2e44da7fb.1645104518.git.michal.simek@xilinx.com
ZYNQMP_PSU_INIT_ENABLED is called only when BOARD_EARLY_INIT_F is defined
that's why cover this dependency in Kconfig.
board_early_init_f() is only part related to
CONFIG_ZYNQMP_PSU_INIT_ENABLED which is disabled now that's why disable
BOARD_EARLY_INIT_F and also build board_early_init_f() only when
CONFIG_BOARD_EARLY_INIT_F is enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/d89253ec1590cd513dcd4bfbedebae618bd6d605.1645104518.git.michal.simek@xilinx.com
The commit 9855034397 ("fdt: Don't call board_fdt_blob_setup() without
OF_BOARD") forced to enable OF_BOARD for platforms which provide DT
externally. Zynq/ZynqMP boards are using this feature for a long time
that's why there is a need to enable it by default.
Also code expects to return error in case of error that's why also fill it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/9f11bbffe2849f4da7d72712082d579262fe8fd8.1645104518.git.michal.simek@xilinx.com
Add support for ethernet on the imx8mn-ddr4-evk.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The function wrongly will return the card detection status of the SD card
(USDHC2) for the eMMC (USDHC1). Thus booting from eMMC without an inserted
SD card will fail.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
With binman generating flash.bin, it's not longer necessary to
specify either the location of ATF nor is it necessary to
specify building flash.bin, so let's update the build instructions
to remove those. While in here, update the revision of ATF and
DDR firmware so both Mini and Nano reference the same revision.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Use IS_ENABLED(CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG) to make the code
more readable and fix checkpatch.pl warning
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
- a37xx: pci: Cleanup and minor fix for root port check (Pali)
- pci: mvebu: Ensure that root port is always on root zero bus (Pali)
- kwbimage: Fix dumping DATA registers for v0 images (Pali)
- kwbimage: Support for parsing extended v0 format (Pali)
- a37xx: Fix code and update DTS files to upstream version (Pali)
- a37xx: Fix and extend building memory map (Pali)
- ddr: marvell: a38x: fix BYTE_HOMOGENEOUS_SPLIT_OUT decision (Marek)
- mvebu: Optionally reset board on DDR training failure (Marek)
Armada 3720 DTS files in upstream kernel use ethernet nodes named
'ethernet@30000' and 'ethernet@40000'. U-Boot have them named 'neta@30000'
and 'neta@40000'. To have Turris Mox U-Boot board code independent of
ethernet node names, find ethernet node via alias.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Update the board_fit_config_name_match() to choose the right dtb
based on the board name read from EEPROM.
Also restrict multpile EEPROM reads by verifying if EEPROM is already
read.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
j721e-sk doesn't have any daughter cards, so disable daughter
card probing inside board_late_init() and spl_board_init() for
j721e-sk.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
J721E EVM has EEPROM populated at 0x50. J721E SK has EEPROM populated
at next address 0x51 in order to be compatible with RPi. So start
looking for TI specific EEPROM at 0x50, if not found look for EEPROM at
0x51.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
board_late_init(), setup_board_eeprom_env() and setup_serial() is
called only under CONFIG_BOARD_LATE_INIT, so guard these functions
with the same. Also, reorder these functions to place it under
single #ifdef
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
The Pogoplug E02 board has the network chip Marvell 88E1116R. Convert
to Driver Model and use uclass mvgbe and the compatible driver M88E1118R
to bring up Ethernet.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- As the result of the migration to Driver Model, this u-boot image has
grown substantially (about 100K, give or take). The old envs location
at 0x60000 (384k) is no longer possible. Move it to 0xC0000 (768K).
- Miscellaneous changes: Move constants to .c file and remove header file
board/cloudengines/pogo_e02/pogo_e02.h, use CONFIG_SYS_THUMB_BUILD to
keep u-boot image under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Dockstar board has the network chip Marvell 88E1116R. Convert to
Ethernet driver model, and use uclass mvgbe and the compatible driver
M88E1118R to bring up Ethernet.
- Add CONFIG_DM_ETH and associated configs.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Add CONFIG_PHY_MARVELL to properly configure the network.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Miscellaneous changes: Move constants to .c file and remove
header file board/Seagate/dockstar/dockstar.h, use
CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, add CONFIG_HUSH_PARSER, use BIT macro, and cleanup comments.
- Note: This patch is a RESEND for a previous patch:
https://patchwork.ozlabs.org/project/uboot/patch/20210812051854.1340-2-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Miscellaneous changes: Move constants to .c file and remove header file
board/iomega/iconnect/iconnect.h. Add CONFIG_HUSH_PARSER, use BIT macro,
and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Globalscale Technologies Dreamplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up both network
port 0 and 1. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add myself as maintainer (this board seems to be orphaned,
could not contact Jason Cooper using current email).
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/dreamplug/dreamplug.h, cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Currently, if MTD NOR is enabled then U-Boot tries to issue flash
commands even when CFI flash DT node is not present. This causes
access fault on RISC-V emulators or ISS which do not emulate CFI
flash. To handle this issue, we implement is_flash_available() for
qemu-riscv board which will return 1 only if CFI flash DT node is
present.
Fixes: d248627f9d ("riscv: qemu: Enable MTD NOR flash support")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Enable support for HTIF console so that we can use QEMU RISC-V U-Boot
on RISC-V emulators and ISS having it.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This is supposed to be a build-system flag. Move it there so we can
define it before linux/kconfig.h is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The function to return the default MMC device for the environment
already has a __weak instance doing exactly the same thing. Remove
the superfluous one.
Signed-off-by: Adam Ford <aford173@gmail.com>
The function to return the default MMC device for the environment
already has a __weak instance doing exactly the same thing. Remove
the superfluous one.
Signed-off-by: Adam Ford <aford173@gmail.com>
Sync with the latest DDR initialization from Phytec, which
uses version 1.2 of NXP's i.MX7D DRAM Register Programming Aid
spreadsheet.
This updated DDR initialization fixes occasional system freeze.
Signed-off-by: Fabio Estevam <festevam@denx.de>
As suggested in commit 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") for imx8mm_evk, it is possible to produce
single bootable image via binman. This restores the original behavior in
distros, where only one boot container is used to create target image.
Perform similar adaptions in order to provide single bootable image for
imx8mn-ddr4-evk derivate.
Update documentation to drop additional step of copying u-boot.itb
Fixes: 353dfe4b43 ("imx8mn-ddr4-evk: switch to use binman")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The new configs/imx28_xea_sb_defconfig is introduced to facilitate
building the single binary u-boot.sb fox XEA board.
The biggest distinction from "normal" XEA imx28_xea_sb_defconfig is
support for USB mass storage devices (pen drives).
To achieve that, the CONFIG_DM_USB is enabled and supported.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change provides the possibility to build XEA (imx287 based) board
U-Boot as a single binary (without support for CONFIG_SPL_FRAMEWORK).
The generated u-boot.sb can be used in the factory environment to for
example perform initial setup or HW testing.
It can be used with 'uuu' utility
(SDPS: boot -f /srv/tftp/xea/u-boot.sb)
In the configs/imx28_xea_defconfig one needs to disable following configs:
# CONFIG_SPL_BLK is not set
# CONFIG_SPL_FRAMEWORK is not set
The board_init_ll() is used in arch/arm/cpu/arm926ejs/mxs/start.S, which
is utilized when CONFIG_SPL_FRAMEWORK is disabled.
However, when it is enabled - the arch/arm/cpu/arm926ejs/start.S is used,
which requires the lowlevel_init() function.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Extension boards can be added to Compulab's iot-gate-imx8mm.
We implement extension board manager for detecting the extension
boards.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: uboot-imx <uboot-imx@nxp.com>
8ULP ROM should read the LPOSC trim BIAS fuse to fill the CGC0
LPOSCCTRL[7:0], but it writes a fixed value on A0.1 revision.
A0.2 will fix the issue in ROM. But A0.1 we have to workaround
it in SPL by setting LPOSCCTRL BIASCURRENT again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The setting does not have effect because we should set it after
power on the PS16 for NIC AV.
So move it after upower_init which has powered on all PS
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board use IO9 of PCA6416 on LPI2C0 and TPM0 for MIPI DSI MUX and
backlight. However the LPI2C0 and TPM0 are M33 resources, in this
patch we simply access them, but this is a temporary solution.
We will modify it when M33 FW changes to set MIPI DSI panel as default
path and enable backlight after reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add EA iMX7ULP COM board support for building SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
This is the promised second part of the sunxi PR for 2022.04, albeit
technially outside of the merge window. We were working on this full
steam since the beginning of the year, and it deserves to be merged,
I think.
The main attraction is support for the F1C100s SoC, which sports a
venerable ARM926 core. Support for this SoC and the LicheePi Nano board
has been in Linux for years, and U-Boot patches were posted mid last
year already.
The new SoC using ARMv5 also means that the bulk of the new code should
not touch any existing boards, although we did some refactorings first,
of course, which actually cleans up some existing sunxi code.
Compile tested for all 160 sunxi boards, and briefly tested on BananaPi M1,
OrangePi Zero, Pine64 and Pine-H64. Tested by others on their boards,
including F1C100s and F1C200s devices.
Generic Timer Extension is not available on SUNIV.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add the PDU001 board specific DT files to MAINTAINERS. This should
help for better tracking of changes to these files.
Signed-off-by: Felix Brack <fb@ltec.ch>
The available ram can be limited by ram_top as that depends on the
reserved memory nodes provided by the device-tree (via
board_get_usable_ram_top), so make sure to respect ram_top when setting
up bootm_size to avoid overlapping reserved memory regions (e.g. memory
used by OP-TEE).
The same logic is available in env_get_bootm_size when bootm_size is
not defined by the default environment.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Link: https://lore.kernel.org/r/20220120191730.2009270-1-ricardo@foundries.io
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Commit 045ecf8992 ("configs: enable DM_ETH support for LS1046ARDB")
resulted in the PCI bus no longer being implicitly enumerated.
However, this is necessary for the fdt pcie fixups to work.
Therefore, similar to commit 8b6558bd41 ("board: ls1088ardb:
transition to DM_ETH"), pci_init() is now called in the board_init()
routine when CONFIG_DM_ETH is active.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
CC: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
IFC-NOR and QSPI are muxed on SoC.
So disable IFC node in dts if QSPI is enabled or disable QSPI node in dts
in case QSPI is not enabled.
"ifc/nor" will be changed to "memory-controller/nor" in linux. So need to
modify "ifc/nor" to "memory-controller/nor" in fdt_path_offset().
Signed-off-by: Jianpeng Bu <jianpeng.bu@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Commit eb1986804d ("configs: enable DM_ETH support for LS1043ARDB")
resulted in the PCI bus no longer being implicitly enumerated.
However, this is necessary for the fdt pcie fixups to work.
Therefore, similar to commit 8b6558bd41 ("board: ls1088ardb:
transition to DM_ETH"), pci_init() is now called in the board_init()
routine when CONFIG_DM_ETH is active.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
CC: Priyanka Jain <priyanka.jain@nxp.com>
CC: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The SCRATCHRW4 is only used in secure boot scenario that is unsupported by
our design, so this address can be stolen for storing POST status.
The SCRATCHRW4 is initialized to zero at core rest.
Using a DDR address was unfortunate choice, the DDR at boot time has a
random contend and it happens that sometimes is matching POST magic number.
This behavior can lead to undefined POST behavior and u-boot ending in
failbootcmd command.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds default defconfig for u-boot update version, the u-boot
update defconfig is a copy of the default (factory) defconfig with:
- adapted text base and environment addresses
- explicit flag that this is a field updated u-boot version
At the time of implementation this version is only used to verify the
update procedure, in future depend on the needs this defconfig can be
extended with additional options.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This was probably broken when mainlining, CONFIG_FSL_DEVICE_DISABLE is
not Kconfig but whitelisted.
It's fine to be without flag as this is always enabled for abec1020
(pg-wcom-ls102xa.h)
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds default defconfig for u-boot update version, the u-boot
update defconfig is a copy of the default (factory) defconfig with:
- adapted text base and environment addresses
- explicit flag that this is a field updated u-boot version
At the time of implementation this version is only used to verify the
update procedure, in future depend on the needs this defconfig can be
extended with additional options.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Field fail-safe u-boot update procedure for pg-wcom boards is defined and
implemented by patch: 59b3403.
This patch invokes the update procedure for pg-wcom-ls102x designs during
early misc_init_f execution.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch provides possibility for field fail-safe u-boot updates.
The implementation can be used on all pg-wcom boards that are booting from
parallel NOR flash.
When used in a board design, provided check_for_uboot_update function will
start new u-boot at defined location if updateduboot envvar is set to yes.
With this implementation it is expected that factory programmed u-boot
will always stay as it is, and optionally new u-boot can be safely
programmed by embedded software when the unit is rolled out on the field.
It is expected check_for_uboot_update to be called early in execution
before relocation (*_f) once SoC is basically initialized and environment
can be read, with this possibilities to not be able to fix a u-boot bug by
a u-boot update are reduced to minimum.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The EBOOTCNT is a reserved persistent static memory area in QRIO,
and similar to BOOTCNT is intended to be used as boot counter location.
Comparable to BOOTCNT that is reserved for u-boot main bootcount
infrastructure, EBOOTCNT is intended to be used for pg-wcom board
specific purposes (e.g implementing early boot counter for fail-safe
u-boot update).
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The PHY for the debug interface was placed on the board for the
pg_wcom_ls102x. Hence only when a piggy is plugged, a RJ45 jack
including magnetics is connected to the MDI of the PHY. Without a
piggy the MDI lines are left floating and it does not make sense to
have an active debug PHY.
In case of expu1 an active PHY without a piggy even led to increased
jitter for syncE.
This patch only deactivates the prst line of the debug PHY when a piggy
is detected persent.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachienergy.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It is necessary to read the status of the PGY_PRES pin
so that u-boot can react accordingly.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachienergy.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
QRIO library now supports direct read of the test pin status.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is a request from HW designers to use this QRIO pin for detecting
DIC26_SELFTEST status instead of a GPIO pin.
This pin is typically used during production for executing POST tests and
starting test ESW bank.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Traverse Technologies Ten64 family boards use a microcontroller
to control low level board functions like startup and reset,
as well as holding details such as the board MAC address.
Communication between the CPU and microcontroller is via
I2C.
To keep the driver structure clean between the Ten64 board
file, DM_I2C, and a future utility command, this driver
has been implemented as a misc uclass device.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The GoFlex Home board has the network chip Marvell 88E1116R.
Use uclass mvgbe and the compatible driver M88E1118R to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: use CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Use versioned URLs for line numbers as branches are moving in the time and
use master branch for mv-ddr-marvell where is up-to-date code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
a bit delayed, the first batch of the sunxi pull request for this cycle.
This is mostly collecting some patches that were lying around for a
while, plus some recent fixes. Nothing too exciting at this point, but
of course they should be merged nevertheless.
There is the much bigger F1C100s SoC support coming up, which I hope to
be able to send in the next few days, along with the removal of sunxi's
lowlevel_init usage.
Compile tested for all 159 sunxi boards, plus briefly tested on BananaPi
M1, OrangePi Zero, Pine64 and Pine-H64.
For sunxi boards with the AXP209, AXP221, AXP809, and AXP818 PMICs
(plus possibly others, I only confirmed the datasheets for these),
it is sometimes desirable to not boot whenever the device is
plugged in. An example would be when using the NTC CHIP inside a
PocketCHIP.
This provides a configurable option to check if bit 0 of
register 0 of the PMIC says it was powered because of a power button
press (0) or a plug-in event (1). If the value is 1 and this option
is selected, the device shuts down shortly after printing a message
to console stating the reason why it's shutting down. Powering up the
board with the power button is not affected.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
[Andre: reword to speak of boot, remove #ifdefs]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since DRAM_MEMORY_TYPE_DDR3 is defined let's use it instead of magic
number 3.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Sometimes some ethernet aliases do not exist in U-Boot DT but they
exist in the DT used to boot the system (for example, modified via DT
overlays). In this situation setup_environment is called again in
ft_board_setup() to generate macaddr environment variable for them.
However now the call to fdt_fixup_ethernet() is moved before the call
of ft_board_setup().
Call fdt_fixup_ethernet() again to add MAC addresses for the extra
ethernet aliases.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[updated commit message]
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Solve compilation issue on undefined CONFIG_SYS_MMC_ENV_DEV when
CONFIG_ENV_IS_IN_MMC is deactivated on STMicroelectronics boards
defconfig
Fixes: 9f97193616 ("board: stm32mp1: use CONFIG_SYS_MMC_ENV_DEV when available")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
MAX_SEARCH_PARTITIONS is the highest possible partition number.
Do not skip the last partition in board_get_alt_info_mmc().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
- meson64_android: define raw parts for bootloader to permit flashing with fastboot
- vim3: configure serial# from ethaddr to permit using fastboot like sei510/610
-----BEGIN PGP SIGNATURE-----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=tP9Y
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220120' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Disable CONFIG_NET_RANDOM_ETHADDR for android configs
- meson64_android: define raw parts for bootloader to permit flashing with fastboot
- vim3: configure serial# from ethaddr to permit using fastboot like sei510/610
Code in board_fix_fdt() already detects connected MOX modules so there is
no need to have custom comphy_update_map() function for setting serdes
speeds.
This change sets phy-mode for MOX SFP module (when present) to sgmii.
Comphy driver then sets sgmii serdes speed for this module to 1.25G.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
On of the MiniPCIe ports on Turris Omnia is also a mSATA port. Whether
it works in SATA or PCIe mode is determined by a strapping pin, which
value is read from the MCU.
We already determine which type of card is connected when configuring
SerDeses.
But until now we left both SATA and PCIe port 0 nodes in device tree
enabled, and so the SATA driver is probed in U-Boot / Linux even if we
know there is no mSATA card, and similarly PCIe driver tries to link on
port 0 even if we know there is mSATA card, not a PCIe card.
Fixup device tree blob to disable SATA node if mSATA card is not
present, and to disable PCIe port 0 node if mSATA card is present.
Do this for U-Boot's DT blob before relocation and also for kernel DT
blob before booting.
This ensures that software does not try to use SATA or PCIe HW when
corresponding PHY is not configured.
Signed-off-by: Pali Rohár <pali@kernel.org>
[ refactored and fixed some issues ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add macro fdt_for_each_node_by_compatible() to allow iterating over
fdt nodes by compatible string.
Convert various usages of
off = fdt_node_offset_by_compatible(fdt, start, compat);
while (off > 0) {
code();
off = fdt_node_offset_by_compatible(fdt, off, compat);
}
and similar, to
fdt_for_each_node_by_compatible(off, fdt, start, compat)
code();
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
=HtB+
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
asm/mmu.h include is currently guarded by CONFIG_ADDR_MAP ifdef because
the header is only present on arm and powerpc. In order to remove the
dependency on this header and the associated ifdef, move init_addr_map()
declaration to init.h, since it is only called during the common init
sequence.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
- Let am335x_evm use the CPSW or PRUSS ethernet.
- Implement timer_get_boot_us in the omap timer driver
- gpmc bitflip, QSPI clock calculation on am437x, da8xx_gpio bugfixes
- Assorted K3 updates
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmHlNOccHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyL0JB/4+sKNWPMgOYvP2uLCC
euRGomhxJ5WmxJVDtJeBIRg0YKSkwnE8JwIN2qqGu15xJnNX9Ck5qnIMPbiZ/io9
ocW5Z/4C4rfJX/OzD6FtmbMNsvG/umVmZkjRU3ryRXKGyNVpVjLQ2EEECaJfk1WZ
Nd/J6/Jo8nafb1x4OeY+F6+xwZAuj7Mrun9SsDSyrIvmEqSnaQNioj+lStkauL51
NwQgBxZBQmbdCgF7Ooy6rYlXZBR6r/rgWB9n3RP8emDCwfCMul9HOMT432oKNbhW
bGrcMu9AWv/pgzXogxSzYbEdTAnoVEODtU1suCa8LV6KJPEG693gARnRm/KjvPHa
FfsK
=39IY
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.04-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2022.04 cycle:
This small feature set includes few changes for sama7g5 and sama7g5ek:
turn blue led on at boot, changes required for the Rev4 of the board,
better sync with the Linux DT with regards to the new DT nodes.
The am335x-ice-v2 board's Ethernet ports can be configured
in 'MII' or 'RMII' mode to be connected to 'PRUSS' or 'CPSW'
Ethernet subsystems.
This patch sets the environment variable 'ice_mii' to
'mii' or 'rmii' accordingly. Based on that we choose the
appropriate board devicetree i.e. 'am335x-ice-v2.dtb' or
'am335x-ice-v2-prueth.dtb'.
Since there are 2 Ethernet ports with 2 modes, there can be 4
configurations but for now we consider both ports in different modes
to be an invalid configuration and prevent boot in that case.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[Amjad: use overlay instead of using new am335x-ice-v2-prueth.dtb]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Make prueth_is_mii be marked __maybe_unused]
Signed-off-by: Tom Rini <trini@konsulko.com>