It isn't generally save to execute applications outside of U-Boot with caches
enabled due to the way the Blackfin processor handles caches (requires
software assistance). This patch disables caches before booting an ELF or
just booting raw code. The previous discussion on the patch was that we
wanted to use weaks instead, but that proved to not be feasible when multiple
symbols are involved, which puts us back at the ifdef solution. I've
minimized the ugliness by moving the setup step outside of the main function.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When the LM73 temperature sensor measures a temperature below 0 C, the
current driver does not perform sign extension, so the result returned is
512 C too high. This patch fixes the problem, and does general cleanup
of the code.
Signed-off-by: Larry Johnson <lrj@acm.org>
Some NOR flash chip from Spansion, for example, the s29ws-n MirrorBit
series require different addresses for buffered write commands. Define a
configuration option to support buffered writes on those chips. A more
elegant solution would be to automatically detect those chips by parsing
their CFI records, but that would require introduction of a fixup table
into the cfi_flash driver.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
32-bit wide ECC memory modules report 40-bit width.
Changed the DIMM data bus width test to 'less than 64' instead of 'equal 32'.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Currently the serdes will not be initializated due to the
partid's error.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Currently the SATA controller clock is configured as CSB clock,
usually the CSB clock is 400/333/266MHz.
However, The SATA IP block is only guaranteed to operate up to
200 MHz as stated in the HW spec.
The bug is reported by Joe D'Abbraccio <ljd015@freescale.com>
This patch makes the SATA clock as half of CSB clock.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
We were looking at the wrong memory offset to determine of a secondary
cpu had been spun up or not. Also added a warning message if the
all the secondary cpus we expect don't spin up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The recent change introduced by 'Update SVR numbers to expand support'
now requires that we use SVR_SOC_VER instead of SVR_VER if we want
to compare against a particular processor id.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch reworks the default environment on Kilauea/Haleakala. Now
"net_nfs" for exmaple uses the device-tree style booting formerly know
as "net_nfs_fdt". Also the addresses in RAM were changed because of the
new image booting support, which check for image overwriting. So the
addresses needed togeet adjusted.
Signed-off-by: Stefan Roese <sr@denx.de>
Since the new image support checks for image overwriting, the default
environment needs to get adjusted to use correct addresses.
Signed-off-by: Stefan Roese <sr@denx.de>
The patch 70431e8a73 (Make MPC83xx one step
closer to full relocation.) doesn't use CFG_MONITOR_BASE anymore. But
on 4xx systems _start currently cannot be used for this calculation.
So revert back to the original version for now.
Signed-off-by: Stefan Roese <sr@denx.de>
