Disable a few things which interfere with the EFI init. This allows the
Minnowboard MAX to boot into EFI, load a U-Boot payload then boot to the
U-Boot prompt.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When U-Boot is running from EFI some of the x86 init is replaced with
EFI-specific init. For example, since DRAM has already been set up, we only
need to find it, not init it. Add these functions so that boards can easily
allow booting from EFI if required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When U-Boot runs as an EFI payload it needs to avoid setting up the CPU
again. Also U-Boot currently does not handle interrupts for many devices, so
run with interrupts disabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The EFI stub provides information to U-Boot in a table. This includes the
memory map which is needed to decide where to relocate U-Boot. Collect this
information in the early init code and store it in global_data.
Fix up the BIST code at the same time since we don't have it when booting
from EFI and can assume it is 0.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Most EFI implementations use 64-bit. Add a way to build U-Boot as a 64-bit
EFI payload. The payload unpacks a (32-bit) U-Boot and starts it. This can
be enabled for x86 boards at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Improvements to how the payload is built:
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The procedure to drop from 64-bit mode to 32-bit is a bit messy. Add a
function to take care of it. It requires identity-mapped pages and that
the calling code is running below 4GB.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Rather than add these as open-coded values, create an enum with the commonly
used flags.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add support for building a 32/64-bit EFI stub for x86. This involves
building the startup and relocation code for either i386 or x86_64.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to be able to load U-Boot onto a board even if is it already
running EFI. This can allow access to the U-Boot command interface, flexible
booting options and easier development.
The easiest way to do this is to build U-Boot as a binary blob and have an
EFI stub copy it into RAM. Add support for this feature, targeting 32-bit
initially.
Also add a way to detect when U-Boot has been loaded via a stub. This goes
in common.h since it needs to be widely available so that we avoid redoing
initialisation that should be skipped.
Signed-off-by: Simon Glass <sjg@chromium.org>
Improvements to how the payload is built:
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add a linker script and relocation code for building 64-bit EFI
applications. This can be used for the EFI stub.
Signed-off-by: Simon Glass <sjg@chromium.org>
Improvements to how the payload is built:
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This code currently requires CONFIG_SYS_TEXT_BASE but this should be
unnecessary. As a first step, remove the build-time limitation and report an
error instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This contains just enough to bring up the serial UART.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add support for the efi-x86 board, which supports running U-Boot as an
EFI 32-bit application.
Signed-off-by: Ben Stoltz <stoltz@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add the required x86 glue code. This includes the initial start-up,
relocation and jumping to efi_main(). We also need to avoid fiddling with
interrupts.
Signed-off-by: Ben Stoltz <stoltz@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Bring in this file from Linux 4.1. It supports relocation features specific
to x86.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When running as an EFI application we must skip relocation. Add support for
this in the x86 relocation code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust the toolchain flags to build U-Boot as a relocatable shared library,
as required by EFI.
Signed-off-by: Ben Stoltz <stoltz@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
When running as an EFI application, U-Boot must request memory from EFI,
and provide access to the boot services U-Boot needs.
Add library code to perform these tasks. This includes efi_main() which is
the entry point from EFI. U-Boot is built as a shared library.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On x86 the global_data pointer is provided through a somewhat-bizarre and
x86-specific mechanism: the F segment register is set to a pointer to the
start of global_data, so that accesses can use this build-in register.
When running as an EFI application we don't want to mess with the Global
Descriptor Table (GDT) and there is little advantage (in terms of code size)
to doing so.
Allow global_data to be a simple variable in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fix a typo, remove an unused field and make sure to use existing #define
constants instead of open-coded values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The GDT works but technically the length is incorrect. Fix this and add a
comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is now handled by generic U-Boot code so we do not need an x86 version.
It is no-longer called, so remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These flags now overlap some global ones. Adjust the x86-specific flags to
avoid this. Since this requires a change to the start.S code, add a way for
tools to find the 32-bit cold reset entry point. Previously this was at a
fixed offset.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fix a typo, improve some comments and add a little more detail in some
cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add PCI IRQ routing information in the board device tree and enable
writing PIRQ routing table and MP table.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Bayley Bay board is a BayTrail based board. Add this board
with existing baytrail fsp support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds the microcode blob for BayTrail-I B0 stepping,
CPUID signature 30671h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
BayTrail FSP Gold4 release adds one UPD parameter to control IGD
enable/disable.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a cpu1 node to the device tree and enable the MP initialization
on QEMU targets (i440fx and q35).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
When running SMP configuration on QEMU (tcg mode, no kvm), there is
a busy loop in start_aps(), calling udelay(), that waits for APs to
show up online. However, there is a chance that VCPU1 will be timeout
waiting, IOW the secondary VCPUs haven't started their execution yet.
This patch adds a 'pause' instruction in __udelay() only for QEMU
target, to give other VCPUs a chance to run. When QEMU sees the
'pause' instruction, it will yeild the execution to other CPUs.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Define base address of both usb xhci controllers in lsch3 config
in the format (IMMR + offset) for LS2085A
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define CONFIG_SYS_CACHELINE_SIZE for LS2085A which is required by
USB XHCI stack for alignment
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Bootrom will put cpus into WFE state when boot cpu release cpus, so
target cpu cannot correctly go to spin state.
Add 'sev' to wakeup non-boot cpu that hold on bootrom space, let target
cpu can fall into u-boot spin table.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. Define two structures mx6ul_iomux_ddr_regs and mx6ul_iomux_grp_regs.
2. Add a new function mx6ul_dram_iocfg to configure dram io.
3. Refactor MMDC1 macro, discard "#ifdef CONFIG_MX6SX". Since
only mmdc0 channel exists on i.MX6SX/UL, redefine MMDC1 macro support
runtime check, but not hardcoding #ifdef macros.
4. Introduce mx6ul-ddr.h, which includes the register address for DRAM
IO configuration.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1.Update WDOG settings.
2.No need to gate/ungate all PFDs for i.MX6UL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
i.MX6UL features an Cortex-A7 core, it does not have PL310 as other i.MX6
chips. To Cortex-A7 core, If D-Cache is enabled, L2 Cache is enabled.
There is on specific switch for on/off L2 Cache, so default select
SYS_L2CACHE_OFF.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1. Add enet, uart, i2c, ipg clock support for i.MX6UL.
2. Correct get_periph_clk, it should account for
MXC_CCM_CBCDR_PERIPH_CLK2_PODF_MASK.
3. Refactor get_mmdc_ch0_clk to make all i.MX6 share one function,
but not use 'ifdef'.
4. Use CONFIG_FSL_QSPI for enable_qspi_clk, but not #ifdef CONFIG_MX6SX.
5. Use CONFIG_PCIE_IMX for pcie clock settings, use CONFIG_CMD_SATA for
sata clock settings. In this way, we not need "#if defined(CONFIG_MX6Q)
|| defined....", only need one CONFIG_PCIE_IMX in header file.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Since i.MX6UL's cache line size is 64bytes, need to
define the macro CONFIG_SYS_CACHELINE_SIZE to 64 for i.MX6UL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1. Update imx register base address for i.MX6UL.
2. Remove duplicated MXS_APBH/GPMI/BCH_BASE.
3. Remove #ifdef for register addresses that equal to
"AIPS2_OFF_BASE_ADDR + 0x34000" for different chips.
4. According fuse map, complete fuse_bank4_regs.
5. Move AIPS3_ARB_BASE_ADDR and AIPS3_ARB_END_ADDR out of #ifdef CONFIG_MX6SX,
because we can use runtime check
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Add i.MX6UL pins IOMUX file which defines the IOMUX settings for choose.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Add MXC_CPU_MX6UL for i.MX6UL CPU type which is got at runtime from
DIGPROG register. But the value has been occupied by MXC_CPU_MX6D which
is not real id from DIGPROG register, so change i.MX6D to value 0x67 which
was not occupied.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
CPU_V7 is already selected by ARCH_MX6, so no point in selecting it again
by boards that depend on ARCH_MX6.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
cm-fx6 is an MX6 based board, and the menuconfig hierarchy should
reflect that. Make TARGET_CM_FX6 dependant on ARCH_MX6.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The i.MX6DQP has a PRG module, need to enable its clock for using IPU.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Brown Oliver <B37094@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Since the i.MX6QP has fixed the issue in boot ROM, so remove the workaround
for i.MX6QP.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Since i.MX6QP changes some CCM registers, so modify the clocks settings to
follow the hardware changes.
In c files, use runtime check and discard #ifdef.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add cpu type for i.MX6QP/DP.
This patch also fix is_mx6dqp(), since get_cpu_rev can return MXC_CPU_MX6QP
and MXC_CPU_MX6DP, we should use:
(is_cpu_type(MXC_CPU_MX6QP) || is_cpu_type(MXC_CPU_MX6DP)).
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Serdes Lanes availability on T4160 and T4080 are same, which serdes 2 & 3
support 8 Lanes, but serdes 1 & 4 support only 4 Lanes E/F/G/H, Lanes
A/B/C/D are not available, updated the serdes table accordingly with
some minor fix.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For running Chain of Trust when doing Secure Boot from NAND,
the Bootscript header and bootscript must be copied from NAND
to RAM(DDR).
The addresses and commands for the same have been defined.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure Boot Target is added for NAND for P3041.
For mpc85xx SoCs, the core begins execution from address 0xFFFFFFFC.
In case of secure boot, this default address maps to Boot ROM.
The Boot ROM code requires that the bootloader(U-boot) must lie
in 0 to 3.5G address space i.e. 0x0 - 0xDFFFFFFF.
In case of NAND Secure Boot, CONFIG_SYS_RAMBOOT is enabled and CPC is
configured as SRAM. U-Boot binary will be located on SRAM configured
at address 0xBFF00000.
In the U-Boot code, TLB entries are created to map the virtual address
0xFFF00000 to physical address 0xBFF00000 of CPC configured as SRAM.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Added routine mmu_set_region_dcache_behaviour() to set a
particular region as non cacheable.
Define dummy routine for mmu_set_region_dcache_behaviour()
to handle incase of dcache off.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Correct the value CONFIG_USB_MAX_CONTROLLER_COUNT macro to 1
for p1025 as it has one USB controller
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MAC1 acts as 1G/10G dual-role MAC on T1024. We introduce
macro SET_FMAN_RX_10G_TYPE2_LIODN for 10G MACs which have
same Port ID and same offset of address with 1G MAC.
Update it to match with the setting of fman in t1024 device
tree, otherwise there is no 'fsl,liodn' in
/proc/device-tree/soc@ffe000000/fman@400000/port@88000/
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
defconfig files are added and SFP version for these platforms
is updated.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Based on Venice2, incorporates Stephen Warren's
latest P2571 pinmux table.
With Thierry Reding's 64-bit build fixes, this
will build and and boot in 64-bit on my P2571
(when used with a 32-bit AVP loader).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Derived from Tegra124, modified as appropriate during T210
board bringup. Cleaned up debug statements to conserve
string space, too. This also adds misc 64-bit changes
from Thierry Reding/Stephen Warren.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
All based off of Tegra124. As a Tegra210 board is brought
up, these may change a bit to match the HW more closely,
but probably 90% of this is identical to T124.
Note that since T210 is a 64-bit build, it has no SPL
component, and hence no cpu.c for Tegra210.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Moved Tegra config options to mach-tegra/Kconfig so that both
32-bit and 64-bit builds can co-exist for Tegra SoCs.
T210 will be 64-bit only (no SPL) and will require a 32-bit
AVP/BPMP loader.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon's 'tegra124: Implement spl_was_boot_source()' needs
a prototype for save_boot_params_ret() to build cleanly
for 64-bit Tegra210.
Signed-off-by: Tom Warren <twarren@nvidia.com>
A subsequent patch will enable the use of the architected timer on
ARMv8. Doing so implies that udelay() will be backed by this timer
implementation, and hence the architected timer must be ready when
udelay() is first called. The first time udelay() is used is while
resetting the debug UART, which happens very early. Make sure that
arch_timer_init() is called before that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On 64-bit SoCs the I-cache isn't enabled in early code, so the default
cache enable functions for 64-bit ARM can be used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Most peripherals on Tegra can do DMA only to the lower 32-bit
address space, even on 64-bit SoCs. This limitation is
typically overcome by the use of an IOMMU. Since the IOMMU is
not entirely trivial to set up and serves no other purpose
(I/O protection, ...) in U-Boot, restrict 64-bit Tegra SoCs to
the lower 32-bit address space for RAM. This ensures that the
physical addresses of buffers that are programmed into the
various DMA engines are valid and don't alias to lower addresses.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
While generating the page tables, a running integer index is shifted by
SECTION_SHIFT (29) and causes overflow for any integer bigger than 7.
The page tables therefore alias to the same 8 sections and cause U-Boot
to hang once the MMU is enabled.
Fix this by making the index a 64-bit unsigned integer and so avoid the
overflow.
swarren notes: currently "i" ranges from 0..8191 on all ARM64 boards, and
"j" varies depending on RAM size; from 4 to 11 for a board with 4GB at
physical address 2GB, as some Tegra boards have.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We should mark PCIe ECAM address range in the E820 table as reserved
otherwise kernel will not attempt to use ECAM.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently cpu-x86 driver is probed only for SMP. We add the same
support for UP when there is only one cpu node in the deive tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The PIIX3 chipset does not integrate an I/O APIC, instead it supports
connecting to an external I/O APIC which needs to be enabled manually.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
On some platforms the I/O APIC interrupt pin#0-15 may be connected
to platform pci devices' interrupt pin. In such cases the legacy ISA
IRQ is not available so we should not write ISA interrupt entry if
it is already occupied.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently during writing MP table I/O interrupt assignment entry, we
assume the PIRQ is directly mapped to I/O APIC INTPIN#16-23, which
however is not always the case on some platforms.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We need walk through all functions within a PCI device and assign
their IRQs accordingly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a RTC node in the device tree to enable DM RTC support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
(Squashed in 'x86: Fix RTC build error on ivybridge')
Turn on cache on the pci option rom area to improve the performance.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Instead of using switch..case for architecture defined exceptions,
simply unify the handling by printing a message of exception name,
followed by registers dump then halt the CPU.
With this unification, it also fixes the wrong exception numbers
for #MF/#AC/#MC/#XM which should be 16/17/18/19 not 15/16/17/18.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some exceptions cause an error code to be saved on the current stack
after the EIP value. We should extract CS/EIP/EFLAGS from different
position on the stack based on the exception number.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Adds the two MIO connected pushbuttons on the zc702 board to the
devicetree as a single multi-key device for us with the gpio-keys driver.
Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add pl310 interrupt to the Zynq devicetree.
Signed-off-by: Alex Wilson <alex.david.wilson@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove unneeded address-cells form intc node because it is already setup
in parent node.
Add missing address-cells and size-cells to eth node to be shared for
every platform DTSes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use the new zynq binding for macb ethernet, since it will disable half
duplex gigabit like the Zynq TRM says to do. Also allow the compatible
cadence gem binding that won't disable half duplex but works otherwise.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The size of the GEM's register area is only 0x1000 bytes.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynq is using Cadence IP where binding is documented in the Linux kernel
and there is no reason to use different binding.
Synchronize it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Due to dependencies between timer and CPU frequency, only changes by
powers of two are allowed. The clocksource driver prevents other
changes, but with cpufreq and its governors it can result in being
spammed with error messages constantly. Hence, remove the 222 MHz OPP.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Zynq UART is Cadence IP and the driver has been renamed accordingly.
Migrate the DT to use the new binding for the UART driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
To silence the warning
cpufreq_cpu0: failed to get cpu0 regulator: -19
from the cpufreq driver regarding a missing regulator,
add a fixed regulator to the DT.
Zynq does not support voltage scaling and the CPU rail should always be
supplied with 1 V, hence it is added in the SOC-level dtsi.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pass directly boot_addr which is LOVEC (0) or HIVEC (0xffff0000).
No reason to use magic values 0 and 1.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define a new config "zynqmp_ep" for ZynqMP instead
of xilinx_zynqmp. This defconfig supports all emulation
platforms of ZynqMP. Also renamed TARGET_XILINX_ZYNQMP
to ARCH_ZYNQMP.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move the zynqmp Kconfig from board to arch
as there may be different boards under same
architecture.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The encoding of the sub instruction used to handle CONFIG_SYS_MALLOC_F_LEN
can only accept certain values, and the set of acceptable values differs
between the AArch32 and AArch64 instructions sets. The default value of
CONFIG_SYS_MALLOC_F_LEN works with either ISA. Tegra uses a non-default
value that can only be encoded in the AArch32 ISA. Fix the AArch64 crt0
assembly so it can handle completely arbitrary values.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[twarren: trimmed Thierry's patch to remove changes already present]
Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, cleaned up patch, wrote description, re-wrote subject]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, stripped out changes not strictly related to warnings]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
While most stm32f4 run at 168 MHz, stm32f429 can work till 180 MHz.
Add option to select 180 MHz through macro CONFIG_SYS_CLK_FREQ.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl>
Cc: u-boot@lists.denx.de
Read device unique ID and set environment variable "serial#".
Value would then be passed to kernel through DTB.
To read ID from DTB, kernel is required to have commit:
3f599875e5202986b350618a617527ab441bf206 (ARM: 8355/1: arch: Show
the serial number from devicetree in cpuinfo)
This commit is already mainline since v4.1-rc1.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl>
Cc: u-boot@lists.denx.de
Because the top-level Makefile forces all the source files
to include include/linux/kconfig.h (see the UBOOTINCLUDE define),
these includes are redundant.
By the way, there are exceptions for the statement above; host
programs. In fact, host tools in U-Boot depend on a particular
board configuration, although I think they should not. So, some
files still include <linux/config.h> to work around build errors
on host tools.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Simon Glass <sjg@chromium.org>
All am33xx device tree are using device-tree, so get_board_rev is never actually
called. Thus, we can get rid of it to make the code easier to maintain.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Despite being defined with __weak, this declaration of get_board_rev will
conflict with the fallback one when ONFIG_REVISION_TAG is not defined.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces code to read the value of the SYS_BOOT pins on the OMAP5, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces code to read the value of the SYS_BOOT pins on the OMAP4, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces code to read the value of the SYS_BOOT pins on the OMAP3, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
OMAP devices might boot from peripheral devices, such as UART or USB.
When that happens, the U-Boot SPL tries to boot the next stage (complete U-Boot)
from that peripheral device, but in most cases, this is not a valid boot device.
This introduces a fallback option that reads the SYS_BOOT pins, that are used by
the bootrom to determine which device to boot from. It is intended for the
SYS_BOOT value to be interpreted in the memory-preferred scheme, so that the
U-Boot SPL can load the next stage from a valid location.
Practically, this options allows loading the U-Boot SPL through USB and have it
load the next stage according to the memory device selected by SYS_BOOT instead
of stalling.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Now that SPL boot devices are clearly defined, we can use BOOT_DEVICE_QSPI_4
instead of a hardcoded value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This cleans up the SPL boot devices for omap platforms and introduces support
for missing boot devices.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces OMAP3 support for the common omap boot code, as well as a
major cleanup of the common omap boot code.
First, the omap_boot_parameters structure becomes platform-specific, since its
definition differs a bit across omap platforms. The offsets are removed as well
since it is U-Boot's coding style to use structures for mapping such kind of
data (in the sense that it is similar to registers). It is correct to assume
that romcode structure encoding is the same as U-Boot, given the description
of these structures in the TRMs.
The original address provided by the bootrom is passed to the U-Boot binary
instead of a duplicate of the structure stored in global data. This allows to
have only the relevant (boot device and mode) information stored in global data.
It is also expected that the address where the bootrom stores that information
is not overridden by the U-Boot SPL or U-Boot.
The save_omap_boot_params is expected to handle all special cases where the data
provided by the bootrom cannot be used as-is, so that spl_boot_device and
spl_boot_mode only return the data from global data.
All of this is only relevant when the U-Boot SPL is used. In cases it is not,
save_boot_params should fallback to its weak (or board-specific) definition.
save_omap_boot_params should not be called in that context either.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The symbolic link to SoC/CPU specific header directory is created
during the build, while it is only necessary for ARM, AVR32, SPARC,
x86, and some CPUs of PowerPC. For the other architectures, it just
results in a broken symbolic link.
Introduce CONFIG_CREATE_ARCH_SYMLINK to not create unneeded symbolic
links.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When core A turning of core B, via tetris DPSC it places the core
B DPSC into transitional state. The core B has to execute wfi instruction
to move its DPSC to the OFF state. This patch add such instruction.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This allows using devices plugged into both ports of the tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On some boards the otg is wired up in host-only mode in this case we
have no vbus-det gpio.
Stop logging an error from sunxi_usb_phy_vbus_detect() in this case, and
stop treating sunxi_usb_phy_vbus_detect() returning a negative errno, as
if a charger is plugged into the otg port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Modify the sunxi musb glue to use the device-model for musb host mode.
This allows using musb in host mode together with other host drivers
such as ehci / ohci, which is esp. useful on boards which use the
musb controller in host-only mode, these boards have e.g. an usb-a
receptacle or an usb to sata converter attached to the musb controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move the musb config and platdata to the sunxi-musb glue, which is where
it really belongs. This is preparation patch for adding device-model
support for the sunxi-musb-host code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for reading the id pin value of the otg connector to the usb
phy code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Start using the new Kconfig options which are available for these now,
and simply always enable them by selecting them as sunxi builds always
include USB support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
With certain features being convert to DM now we want sunxi to default
to having DM enabled for ETH/SERIAL and USB in some cases.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Rini <trini@konsulko.com>
[hdegoede@redhat.com: Also select CONFIG_USB for all sunxi builds]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
At one point in time the utoo-p66 dts file in the kernel had a bogus
uart entry, and it seems like we synced with the kernel at just the wrong
moment.
This commit removes the bogus uart entry, which breaks booting the utoo-p66
when DM_SERIAL=y.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Make possible using a single `u-boot-sunxi-with-spl.bin` binary for both NAND
memory and SD card. Detection where SPL was read from is implemented in
`spl_boot_device`.
Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Some small coding style fixes]
Acked-by: Hans De Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch extracts checking for valid SD card "eGON.BT0" signature from
`board_mmc_init` into function `sunxi_mmc_has_egon_boot_signature`.
Buffer for mmc sector is allocated and freed at runtime. `panic` is
triggered on malloc failure.
Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Small bugfix to make it work for devs other then mmc0]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch adds basic SDIO/MMC booting support to MVEBU SoC's. Since
I don't know of a way to test the boot-device upon runtime, this patch
hardcodes the spl_boot_device instead.
Tested on Marvell DB-88F6820-GP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
The init code for UMC (Unified Memory Controller) and PLL has not
been mainlined yet, but U-boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For the record, describe exactly which device of which vendor
is used on this board.
I2C EEPROM is bound by the generic compatible string, "i2c-eeprom",
so this commit has no impact on the functionality.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With the upcoming addition of the Armada 38x DDR support, which is not
compatible to the Armada XP DDR init code, we need to introduce a new
directory infrastructure. To support multiple Marvell DDR controller.
This will be the new structure:
drivers/ddr/marvell/axp
Supporting Armada XP (AXP) devices (and perhaps Armada 370)
drivers/ddr/marvell/a38x
Supporting Armada 38x devices (and perhaps Armada 39x)
Signed-off-by: Stefan Roese <sr@denx.de>
This code is ported from the Marvell bin_hdr code into mainline
SPL U-Boot. It needs to be executed very early so that the devices
connected to the serdes PHY are configured correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
With the upcoming addition of the Armada 38x SPL support, which is not
compatible to the Armada XP SERDES init code, we need to introduce a new
directory infrastructure. So lets move the AXP serdes init code into
a new directory. This way the A38x code can be added in a clean way.
Signed-off-by: Stefan Roese <sr@denx.de>
Only with disabled MMU its possible to switch the base register address on
Armada 38x. Without this the SDRAM located at >= 0x4000.0000 is also not
accessible, as its still locked to cache.
Signed-off-by: Stefan Roese <sr@denx.de>
Pin muxing needs to be done before UART output, since on A38x the UART
pins need some re-muxing for output to work.
Signed-off-by: Stefan Roese <sr@denx.de>
On A38x switching the regs base address without running from
SDRAM doesn't seem to work. So let the SPL still use the
default base address and switch to the new address in the
mail u-boot later.
Signed-off-by: Stefan Roese <sr@denx.de>
Without calling timer_init(), the xdelay() functions return immediately.
We need to call timer_init() early, so that these functions work and
the PHY and DDR init code works correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anton Schubert <anton.schubert@gmx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch initializes the SATA address windows on Armada XP and
allows it to work with the existing mvsata_ide driver.
It also adds the necessary configuration for the db-mv784mp-gp board.
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Tested-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
These two declarations in arch/x86/include/asm/interrupt.h conflict
with ones in include/linux/compat.h, so x86 boards cannot include
<linux/compat.h>.
The comment /* arch/x86/lib/interrupts.c */ is bogus now, and we do
not see any definitions of disable_irq() and enable_irq() in there.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add the required files for the Broadcom UDC OTG interface.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
USB download gadget functions such as thor and dfu have a separate config option
for the USB gadget part of the code, independent from the command part.
This switches the fastboot USB gadget to the same scheme, for better
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
Move USB controller Base address mapping from ls102xa immap
to fsl xhci header. This is required to remove any warnings when
controller base addresses are mapped for multiple platforms
in their respective files.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Each sandbox peripheral should have a size as well as a base address. This
is required for regmaps to work, so make this change for all nodes that have
an address.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test to confirm that we can probe this device. Since there is no
MMC stack support in sandbox at present, this is as far as the test goes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move sandbox over to use the reset uclass for reset, instead of a direct
call to do_reset(). This allows us to add tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add settings for the last reset generated, and the types of resets which
are permitted. This will be used for testing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since we want clk_ops to be used in U-Boot as a whole, rename the Zynq
version until it can be converted to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Driver-model I2C drivers can be picked up by the linker script rule for
legacy drivers. Change the order to avoid this.
We could make the legacy code depend on !CONFIG_DM_I2C but that is not
necessary and it is good to keep conditions to a minimum.
Signed-off-by: Simon Glass <sjg@chromium.org>
The SPL device tree size must be minimised to save memory. Only include
properties that are needed by SPL - this is determined by the presence
of the "u-boot,dm-pre-reloc" property. Also remove a predefined list of
unused properties from the nodes that remain.
Signed-off-by: Simon Glass <sjg@chromium.org>
When final MMU table is setup in DDR, TCR attributes must match
those of the memroy for cacheability and shareability.
Signed-off-by: Zhichun Hua <zhichun.hua@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
For ARMv8, outer shareable is 0b10, inner shareable is 0b11 at bit
position [13:12] of TCR_ELx register.
Signed-off-by: Zhichun Hua <zhichun.hua@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
DSPI has pin muxing with SDHC and other IPs, this patch check the
value of RCW SPI_PCS_BASE and SPI_BASE_BASE fields, it also check
the "hwconfig" variable. If those pins are configured to DSPI and
"hwconfig" enable DSPI, set the BRDCFG5 of QIXIS FPGA to configure
the routing to on-board SPI memory. Otherwise will configure to SDHC.
DSPI is enabled in "hwconfig" by appending "dspi", eg.
setenv hwconfig "$hwconfig;dspi"
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add dts source files for LS2085AQDS and LS2085ARDB boards.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Bring in required device tree files for ls2085a from Linux. These are
initially unchanged and have a number of pieces not needed by U-Boot.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As SCFG_ENDIANCR register is added to choose little-endian or big-endian
for audio IPs on Rev2.0 silion, little-endian mode is selected.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Base on PSCI services, implement CPU_ON/CPU_OFF for ls102xa platform.
Tested on LS1021AQDS, LS1021ATWR.
Test CPU hotplug times: 60K
Test kernel boot times: 1.2K
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
timer_wait is moved from sunxi/psci_sun7i.S, and it can be converted
completely into a reusable armv7 generic timer. LS1021A will use it
as well.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As the function 'sprintf' does not check buffer boundaries but outputs
to the buffer 'enet' of fixed size (16), this patch removes the function
'sprintf', and uses 'strcpy' instead. It will assign the character
arrays 'enet' and 'phy' the corresponding character strings.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds the infrastructure to update device
tree nodes to convey SMMU stream IDs in the device
tree. Fixups are implemented for PCI controllers
initially.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Stream IDs on ls2085a devices are not hardwired and are
programmed by sw. There are a limited number of stream IDs
available, and the partitioning of them is scenario dependent.
This header defines the partitioning between legacy, PCI,
and DPAA2 devices.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch updates the setting of required bits for A57 cores erratas
- 828024 and 826974
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Dai Haruki <dai.haruki at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Update SoC README to provide details of
- Memory regions
- Memory used by MC and Debug server
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds support to print out the SoC personality.
Freescale LS20xx SoCs (compliant to Chassis-3 specifications) can
have 6 personalities: LS2045AE, LS2045A, LS2080AE, LS2080A,
LS2085AE and LS2085A
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DDR speed should be in MT/s, not MHz.
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
call ft_pci_setup() to disable PCIe dts node if corresponding
PCIe controller is disabled according to RCW
Signed-off-by: Minghuan Lian <Minghuan.Lian at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Commit afbbd413a fixed this for non-driver-model. Make sure that the driver
model code handles this also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust minnowmax to use driver model for PCI. This requires adding a device
tree node to specify the ranges, removing the board-specific PCI code and
ensuring that the host bridge is configured.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver should use the x86 PCI configuration functions. Also adjust its
compatible string to something generic (i.e. without a vendor name).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Store VESA parameters to Linux setup header so that vesafb driver
in the kernel could work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Jian Luo <jian.luo4@boschrexroth.de>
MARK_GRAPHICS_MEM_WRCOMB is not referenced anywhere in the code,
hence remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move X86_OPTION_ROM_FILE & X86_OPTION_ROM_ADDR to arch/x86/Kconfig
and rename them to VGA_BIOS_FILE & VGA_BIOS_ADDR which depend on
HAVE_VGA_BIOS. The new names are consistent with other x86 binary
blob options like HAVE_FSP/FSP_FILE/FSP_ADDR.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Print the meaningful base address and mask of an MTRR range without showing
the memory type encoding or valid bit.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Per CPUID:80000008h result, the maximum physical address bits of
TunnelCreek processor is 32 instead of default 36. This will fix
the incorrect decoding of MTRR range mask.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We should setup fixed range MTRRs for some legacy regions like VGA
RAM and PCI ROM areas as uncacheable. Note FSP may setup these to
other cache settings, but we can override this in x86_cpu_init_f().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We should allow pci config read/write to host bridge (b.d.f = 0.0.0)
in the int1a_handler() which is a valid pci device.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
PCI option rom may use different SS during its execution, so it is not
safe to assume esp pointed to the same location in the protected mode.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
So far interrupt routing works pretty well for any on-chip devices
on Intel Crown Bay. When inserting any PCIe card to any PCIe slot,
Linux kernel is smart enough to do interrupt swizzling and figure
out device's irq using its parent bridge's interrupt routing info
all the way up to its root port. In U-Boot all PCIe root ports'
interrupts were routed to PIRQ E/F/G/H before, while actually all
PCIe downstream ports received INTx are routed to PIRQ A/B/C/D
directly and not configurable. Now we change this mapping so that
any external PCIe device can work correctly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Implement write_mp_table() to create a minimal working MP table.
This includes an MP floating table, a configuration table header
and all of the 5 base configuration table entries. The I/O interrupt
assignment table entry is created based on the same information used
in the creation of PIRQ routing table from device tree. A check
duplicated entry logic is applied to prevent writing multiple I/O
interrupt entries with the same information.
Use a Kconfig option GENERATE_MP_TABLE to tell U-Boot whether we
need actually write the MP table at the F seg, just like we did for
PIRQ routing and SFI tables. With MP table existence, linux kernel
will switch to I/O APIC and local APIC to process all the peripheral
interrupts instead of 8259 PICs. This takes full advantage of the
multicore hardware and the SMP kernel.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The MP table provides a way for the operating system to support
for symmetric multiprocessing as well as symmetric I/O interrupt
handling with the local APIC and I/O APIC. We provide a bunch of
APIs for U-Boot to write the floating table, configuration table
header as well as base and extended table entries.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Remove inline for lapic access routines and expose lapic_read()
& lapic_write() as APIs to read/write lapic registers. Also move
stop_this_cpu() to mp_init.c as it has nothing to do with lapic.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
I/O APIC registers are addressed indirectly. Add io_apic_read() and
io_apic_write() routines to help register access. Two macros for I/O
APIC ID and version register offset are also added.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is no need to populate multiple irq info entries with the same
bus number and device number, but with different interrupt pin. We
can use the same entry to store all the 4 interrupt pin (INT A/B/C/D)
routing information to reduce the whole PIRQ routing table size.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
In fill_irq_info() pci device's function number is written into
the table, however this is not really necessary. The function
number can be anything as OS doesn't care about this field,
neither does the PIRQ routing specification. Change to always
writing 0 as the function number.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We should write correct bus number to the PIRQ routing table for the
irq router from device tree, instead of hard-coded zero.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are 4 usb ports on the Intel Crown Bay board, 2 of which are
connected to Topcliff usb host 0 and the other 2 connected to usb
host 1. USB devices inserted in the ports connected to usb host 1
cannot get detected due to wrong IRQ assigned to the controller.
Actually we need apply the PCI interrupt pin swizzling logic to all
devices on the Topcliff chipset when configuring the PIRQ routing.
This was observed on usb ports, but device 6 and 10 irqs are also
wrong. Correct them all together.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Crown Bay board has a TunnelCreek processor which supports
hyper-threading. Add /cpus node in the crownbay.dts and enable
the MP initialization.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(modified to remove error:
overriding the value of OF_CONTROL. Old value: "y", new value: "y")
This commit cleans up the lapic codes:
- Delete arch/x86/include/asm/lapic_def.h, and move register and bit
defines into arch/x86/include/asm/lapic.h
- Use MSR defines from msr-index.h in enable_lapic() and disable_lapic()
- Remove unnecessary stuff like NEED_LAPIC, X86_GOOD_APIC and
CONFIG_AP_IN_SIPI_WAIT
- Move struct x86_cpu_priv defines to asm/arch-ivybridge/bd82x6x.h, as
it is not apic related and only used by ivybridge
- Fix coding convention issues
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently lapic_setup() is called before calling mp_init(), which
then calls init_bsp() where it calls enable_lapic(), which was
already enabled in lapic_setup(). Hence move lapic_setup() call
into init_bsp() to avoid the duplication.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Most of the MP initialization codes in arch/x86/cpu/baytrail/cpu.c is
common to all x86 processors, except detect_num_cpus() which varies
from cpu to cpu. Move these to arch/x86/cpu/cpu.c and implement the
new 'get_count' method for baytrail and cpu_x86 drivers. Now we call
cpu_get_count() in mp_init() to get the number of CPUs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move MAX_CPUS definition after SMP so that it shows below SMP in the
menuconfig. Also replace the leading spaces in the MAX_CPUS section
with tabs to conform coding standard.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit does the following to clean up x86 cpu dm drivers:
- Move cpu_x86 driver codes from arch/x86/cpu/cpu.c to a dedicated
file arch/x86/cpu/cpu_x86.c
- Rename x86_cpu_get_desc() to cpu_x86_get_desc() to keep consistent
naming with other dm drivers
- Add a new cpu_x86_bind() in the cpu_x86 driver which does exactly
the same as the one in the intel baytrail cpu driver
- Update intel baytrail cpu driver to use cpu_x86_get_desc() and
cpu_x86_bind()
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The call to FspInitEntry is done in arch/x86/lib/fsp/fsp_car.S so far.
It worked pretty well but looks not that good. Apart from doing too
much work than just enabling CAR, it cannot read the configuration
data from device tree at that time. Now we want to move it a little
bit later as part of init_sequence_f[] being called by board_init_f().
This way it looks and works better in the U-Boot initialization path.
Due to FSP's design, after calling FspInitEntry it will not return to
its caller, instead it jumps to a continuation function which is given
by bootloader with a new stack in system memory. The original stack in
the CAR is gone, but its content is perserved by FSP and described by
a bootloader temporary memory HOB. Technically we can recover anything
we had before in the previous stack, but that is way too complicated.
To make life much easier, in the FSP continuation routine we just
simply call fsp_init_done() and jump back to car_init_ret() to redo
the whole board_init_f() initialization, but this time with a non-zero
HOB list pointer saved in U-Boot's global data so that we can bypass
the FspInitEntry for the second time.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Tested-by: Simon Glass <sjg@chromium.org>
Currently the FSP execution environment GDT is setup by U-Boot in
arch/x86/cpu/start16.S, which works pretty well. But if we try to
move the FspInitEntry call a little bit later to better fit into
U-Boot's initialization sequence, FSP will fail to bring up the AP
due to #GP fault as AP's GDT is duplicated from BSP whose GDT is
now moved into CAR, and unfortunately FSP calls AP initialization
after it disables the CAR. So basically the BSP's GDT still refers
to the one in the CAR, whose content is no longer available, so
when AP starts up and loads its segment register, it blows up.
To resolve this, we load GDT before calling into FspInitEntry.
The GDT is the same one used in arch/x86/cpu/start16.S, which is
in the ROM and exists forever.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Add RESET_SEG_START, RESET_SEG_SIZE and RESET_VEC_LOC Kconfig options
and make arch/x86/cpu/config.mk use these options.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Tested-by: Simon Glass <sjg@chromium.org>
This patch adds USB EHCI host support for the common mvebu platform.
Including the Armada 38x.
Tested on DB-88F6280-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for the common AHCI controller on the Marvell
Armada 38x.
Tested on the Marvell DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Armada A38x implements an SDHCI compatible SDIO controller. This patch
enables the Marvell driver to support this SoC. And enables the
SDIO controller if selected by the board configuration.
Tested on Marvell DB-88F6820-GP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Add support in mxc_i2c driver, iomux_v3 and vf610 architecture for the four
I2C instances available in VF610.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
hab_status command returns a memory dump of the hab event log. But the
raw data is not human-readable. Parsing such data into readable event
will help to minimize debbuging time.
Signed-off-by: Ulises Cardenas <Ulises.Cardenas@freescale.com>
Add I2C4 clock support for i.MX6SX. Since we use runtime check,
but not macro, we need to remove `#ifdef ..` in crm_regs.h, or
gcc will fail to compile the code succesfully.
Making the macros only for i.MX6SX open to other i.MX6x maybe not
a good choice, but we have runtime check.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
enable_spi_clock does the same thing with enable_cspi_clock, so
remove enable_cspi_clock.
Remove enable_cspi_clock prototype in header file
convert cm_fx6/spl.c to use enable_spi_clk
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
sun8i-a33-ippo-q8h-v1.2-lcd1024x600.dts has been merged into the upstream
Linux kernel as sun8i-a33-ippo-q8h-v1.2.dts, adjust u-boot to follow.
Note we've never shipped a final u-boot version with the old name, so this
is safe todo.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We have not supported the private library for ARM 64bit.
Prohibit ARM64 boards from enabling it until we make things ready.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The root cause of this problem should now be fixed.
This reverts commit a6a4c542d3.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Pavel Machek <pavel@denx.de>
Tested-by: Pavel Machek <pavel@denx.de>
When CONFIG_SYS_THUMB_BUILD is defined these functions may be called from
Thumb code. Add the required ENTRY and ENDPROC bracketing so that BLX is
used to call these ARM functions, instead of plain BL, which will fail.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Pavel Machek <pavel@denx.de>
Sinlinx SinA33 is a core/daughter board SDK kit from Sinlinx. It has
the A33 SoC, USB host, USB OTG, audio input/output, LCD, camera, SDIO
and GPIO headers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Copy over all the latest dts changes from mripard/sunxi/dt-for-4.2.
This adds a dts file for Sinlinx SinA33 dev board, and the required
changes in the .dtsi files.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A33 adds a pinmux function for UART0 in the PB pin group.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The original code was configuring the external pins after enabling
the R_PIO clock, which meant the configuration never made it to
the pin controller the first time in SPL.
Why this was working before is uncertain. Maybe the state was left
from a previous boot sequence, or RSB just happened to be the default
configuration. However with some A33 chips, SPL failed to configure
the PMIC. This was seen by me and Maxime on the Sinlinx SinA33 dev
board.
Reordering the calls fixed this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit 487b327 ("sunxi: GPIO pin mux hardware-feature-specific function
index defines") renamed all GPIO index defines, but missed the PORT F
UART0 setup functions.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch adds the device tree binding doc for the cadence qspi controller &
also removes the not needed properties from the stv0991 device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
sram size could be different on different socs, e.g. on stv0991 it is 256 while
on altera platform it is 128. It is better to receive it from device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
This patch add the device tree entry for qspi controller & spi flash
memory.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
This patch does all the board configurations required to use the qspi
controller & attached spi flash memory.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
stv0991 has cadence qspi controller for flash interfacing, this
patch configures the device pads & clock for the controller.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
The kernel changed it a long time ago. Also this is now broken
on gcc-5.x.
Reported-by: Andy Kennedy <andy.kennedy@adtran.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Fix missing semicolon in cacheops.h introduced in commit
2b8bcc5a2 (MIPS: avoid .set ISA for cache operations)
Signed-off-by: Tony Wu <tung7970@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
The current GPL only licensing on the device trees makes it very
impractical for other software components licensed under another
license.
To make it easier to reuse them, the device trees for UniPhier
SoCs and boards have already been dual-licensed in Linux.
Follow this trend in U-boot too.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This makes code diff much easier.
Device trees describe hardware attributes, which are independent
of software architecture. It generally makes sense to synchronize
them beyond software projects.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now zynq spi driver platform data is controlled by devicetree,
enable the status by saying "okay" on respective board dts to use
the devicetree generated platdata.
Ex:
&spi1 {
status = "okay";
};
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Enabled CONFIG_DM_SPI and CONFIG_DM_SPI_FLASH for zynq soc.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
[1] Align cache management functions to those in Linux kernel. I.e.:
a) Use the same functions for all cache ops (D$ Inv/Flush)
b) Split cache ops in 3 sub-functions: "before", "lineloop" and
"after". That way we may re-use "before" and "after" functions for
region and full cache ops.
[2] Implement full-functional L2 (SLC) management. Before SLC was
simply disabled early on boot. It's also possible to enable or disable
L2 cache from config utility.
[3] Disable/enable corresponding caches early on boot. So if U-Boot is
configured to use caches they will be used at all times (this is useful
in partucular for speed-up of relocation).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
With new SMP-enabled CPUs with ARC HS38 cores and corresponding support
in Linux kernel it's required to add basic SMP support in U-Boot.
Currently we assume the one and only core starts execution after
power-on. So most of things in U-Boot is handled in UP mode.
But when U-Boot is used for loading and starting Linux kernel right
before jumping to kernel's entry point U-Boot:
[1] Sets all slave cores to jump to the same address [kernel's entry
point]
[2] Really starts all slav cores
In ARC's implemetation of SMP in Linux kernel all cores are supposed to
run the same start-up code. But only core with ID 0 (master core)
processes further while others are looping waiting for master core to
complete some initialization.
That means it's safe to un-pause slave cores and let them execute kernel
- they will wait for master anyway.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
The type of DSPI flash on ls1021aqds is AT45DB021, it has specail
commands and page-size.
Use the special spi flash driver instead of "spi_flash_std" driver.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This reverts commit f76eba38b3.
This patch did not have a full and proper copyright/S-o-b chain.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Conflicts:
include/configs/sun6i.h
include/configs/sun8i.h
Add a new revision CHIP_REV_2_0.
Introudce macro is_mx6dqp, dqp means Dual/Quad Plus.
Since Dual/Quad Plus use same cpu type with Dual/Quad, but different
revision(Major Lower), we use this macro for Dual/Quad Plus.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
The DIGPROG register map:
23 ------- 16 | 15 ------ 8 | 7 --- 0 |
Major upper | Major Lower | Minor |
We also need to account for Major Lower.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
is_soc_rev should return a bool value, so use "==", but not "-",
change (is_soc_rev(CHIP_REV_1_0) > 0) to (soc_rev() > CHIP_REV_1_0).
This patch also add space between "&" for cpu_type(rev) macro.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
This is the first patch to remove the
CONFIG_SYS_EXTRA_OPTIONS.
This patch implements CPU type selection from Kconfig.
Further Kconfig stuff is added later.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.
Remove the configs that behave this way from the archs.
A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:
SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
Update new naming scheme.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
rastaban is a draco version with more flash, more RAM
and faster CPU. Number of partitions is the same but
rootfs partition is different.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
DRA7/AM57xx devices can be operated in many different configurations.
When the SoC is supposed to support a configuration where low power mode
state may involve the SoC completely powered off and DDR is in self
refresh, SoC EMIF controller should not be the master of the reset
signal and an external entity might be in control of things.
The default configuration of Linux on TI evms involve not powering off
the voltage rails (due to various reasons including reliability concerns)
and must not allow DDR reset to be controlled by EMIF. On platforms
where external entity might control the reset signal, this configuration
will be a "dont care".
Fixes: 536d874708 ("ARM: DRA7: Update DDR IO registers")
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The get_max_arm_speed() and get_max_dev_speed() used wrong register
fields to get the maximum speeds. This commit fixes the bug.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently on sun6i after a "reset" the prompt returns and the user can
even type stuff until the watchdog triggers and does the actual reset.
This is somewhat unexpected behavior for the "reset" command, this
commit adds an endless loop to wait for the watchdog to trigger so that
we do not return to the prompt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Vision Systems's Baltos is based on AM335x SoC
from Texas Instruments. This patch adds support
such Industrial PCs in mainline u-boot.
[ balbi@ti.com: updated original patch to current u-boot ]
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Unlike OMAP5, EMIF PHY used in DRA7 will be left in unknown state after
warm reset, emif needs to be configured to bring it back to a known
state. So configure EMIF during warm reset.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Now all the AVR32 boards have been converted into Generic Board.
Select it in Kconfig and clean up defines in header files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
The recent changes for hw leveling on am33xx were not intended for
DDR2 boards, only DDR3. Update emif_sdram_type to take a sdram_config
value to check against. This lets us pass in the value we would use to
configure, when we have not yet configured the board yet. In other cases
update the call to be as functional as before and check an already
programmed value in.
Tested-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
On AM57xx evm I2C5 is used to detect the LCD board by reading the
EEPROM present on the bus.
Enable i2c5 clocks to help that.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
SMP-enabled Linux kernels read the CBAR register in CP15 to find
the address of the SCU registers. After remapping internal
registers, also update the CBAR so the kernel can find them.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
L2 cache may still be enabled by the BootROM. We need to first disable
it before enabling d-cache support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Now all manual mode configurations are done as part of
IO delay recalibration sequence, remove the hack done for
CPSW.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In addition to the regular mux configuration, certain pins of DRA7
require to have "manual mode" also programmed, when predefined
delay characteristics cannot be used for the interface.
struct iodelay_cfg_entry is introduced for populating
manual mode IO timings.
For configuring manual mode, along with the normal pad
configuration do the following steps:
- Select MODESELECT field of each assocaited PAD.
CTRL_CORE_PAD_XXX[8]:MODESELECT = 1(Enable MANUAL_MODE macro along with mux)
- Populate A_DELAY, G_DELAY values that are specified in DATA MANUAL.
And pass the offset of the CFG_XXX register in iodelay_cfg_entry.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
On DRA7, in addition to the regular muxing of pins, an additional
hardware module called IODelay which is also expected to be
configured. This "IODelay" module has it's own register space that is
independent of the control module.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay recalibration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do muxing as part of IOdelay recalibration.
IODELAY recalibration sequence:
- Complete AVS voltage change on VDD_CORE_L
- Unlock IODLAY config registers.
- Perform IO delay calibration with predefined values.
- Isolate all the IOs
- Update the delay mechanism for each IO with new calibrated values.
- Configure PAD configuration registers
- De-isolate all the IOs.
- Relock IODELAY config registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
In addition to the regular mux configuration, certain pins of DRA7
require to have "virtual mode" also programmed.
This allows for predefined delay characteristics to be used by the SoC
to meet timing characterstics needed for the interface.
Provide easy to use macro to do the same.
For configuring virtual mode, along with normal pad configuration add
the following two steps:
- Select MODESELECT field of each assocaited PAD.
CTRL_CORE_PAD_XXX[8]:MODESELECT = 1
- DELAYMODE filed should be configured with value given in DATA Manual.
CTRL_CORE_PAD_XXX[7:4]:DELAYMODE =[0-15] (as given in DATA manual).
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Adopting the pinctrl register definitions from Linux kernel
to be consistent.
Old definitions will be removed once all the pinctrl data
is adapted to new definitions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
do_set_mux32() is redefined in dra7xx and beagle_x15 boards.
IO delay recalibration sequence also needs this.
Making it generic to avoid duplication.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
When DLL_CALIB_INTERVAL is set, an extra delay is added
which is not required and it consumes EMIF bandwidth.
So making the DLL_CALIB_CTRL[8:0]DLL_CALIB_INTERVAL bits to 0.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DDRIO_2 and LPDDR2CH1_1 registers are not present
for DRA7. So not configuring these registers for DRA7xx
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
A generic is_dra72x cpu check is useful for grouping
all the revisions under that. This is used in the
subsequent patches.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
