Commit graph

15240 commits

Author SHA1 Message Date
Michael Trimarchi
35461fe94e imx: imx8mn_smm_s2/s2pro: Enable TrustZone
When the board was added, enabling tzc380 was left off by
mistake. The optee was tested with the following configuration
in s2pro

+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 6MiB */
+		optee_core@5f800000 {
+			reg = <0x00 0x5f800000 0x00 0x600000>;
+		};
+
+		/* 2MiB */
+		optee_shm@5fe00000 {
+			reg = <0x00 0x5fe00000 0x00 0x200000>;
+		};
+	};
+

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
2022-05-20 12:36:48 +02:00
Gaurav Jain
cad77280c3 i.MX8ULP: add display_ele_fw_version api
implement get f/w version api.
print ele f/w version in spl.

Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@nxp.com>
2022-05-20 12:36:47 +02:00
Ye Li
cda8f87349 caam: Fix crash in case caam_jr_probe failed
If probing caam_jr returns failure, the variable "dev" will not be
initialized, so we can't use dev->name for the error print.
Otherwise it will cause crash.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
2022-05-20 12:36:47 +02:00
Peng Fan
8494fe077c imx: toradex/verdin-imx8mm/p: cleanup board watchdog code
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:29 +02:00
Peng Fan
a6924c95d1 imx: verdin-imx8mm/p: cleanup board watchdog code
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:29 +02:00
Peng Fan
09bf8270cf imx: imx8mn_smm_s2: clean up board watchdog code
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
2022-05-20 09:30:29 +02:00
Peng Fan
0726bdd460 imx: imx8mm-mx8menlo: drop unneeded watchdog settings
pinctrl_wdog as u-boot,dm-spl already marked in imx8mm-verdin-u-boot.dtsi,

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2022-05-20 09:30:29 +02:00
Peng Fan
a38ed61643 imx: imx8mp_evk: enable pinctrl_wdog in SPL
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:29 +02:00
Peng Fan
ba06ea8991 imx: imx8mm_evk: enable pinctrl_wdog in SPL
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:29 +02:00
Peng Fan
6d5cc90670 imx: imx8mn_evk: enable pinctrl_wdog in SPL
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:29 +02:00
Peng Fan
6ea118ef9a imx: imx8mm_edm_sbc: Enable SPL_DM_SERIAL
Enable CONFIG_SPL_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-05-20 09:30:28 +02:00
Peng Fan
2232d5f5b7 imx: imx8mm_mx8menlo: Enable DM_SERIAL
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-05-20 09:30:28 +02:00
Tim Harvey
d003d89372 board: gateworks: gw_ventana: remove obsolete file
commit 61cf225053 ("board: gateworks: gw_ventana: use comomn GSC driver")
moved to the common GSC driver and moved remaining board-specific
functions to eeprom.c. The functions in gsc.c are no longer used and it
was removed from the Makefile but the file itself was not removed.
Remove it now.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-05-20 09:30:28 +02:00
Tim Harvey
0cba71c1eb board: gateworks: gw_ventana: add support for GPY111 PHY
The MaxLinear GPY111 PHY is being used on some boards due to part
availability. Add support for this PHY which requires a longer reset
post-delay and RGMII delay configuration.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-05-20 09:30:28 +02:00
Tim Harvey
6fc639461b board: gateworks: venice: enable SPL_DM_SERIAL
The uart2 and its pinmux are already marked with u-boot,dm-spl but we
need to move the call to preloader_console_init() after spl_early_init()
to avoid a board hang as dm can't be used until after spl_early_init()
due to the uart driver not enabling the uart clock.

Remove the manual config of the UART pinmux now that it is no longer
needed.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-05-20 09:30:28 +02:00
Rasmus Villemoes
290ffe5788 imx8m: fix reading of DDR4 MR registers
I was trying to employ lpddr4_mr_read() to something similar to what
the imx8mm-cl-iot-gate board is doing for auto-detecting the RAM
type. However, the version in drivers/ddr/imx/imx8m/ddrphy_utils.c
differs from the private one used by that board in how it extracts the
byte value, and I was only getting zeroes. Adding a bit of debug
printf'ing gives me

 tmp = 0x00ffff00
 tmp = 0x00070700
 tmp = 0x00000000
 tmp = 0x00101000

and indeed I was expecting a (combined) value of 0xff070010 (0xff
being Manufacturer ID for Micron). I can't find any documentation that
says how the values are supposed to be read, but clearly the iot-gate
definition is the right one, both for its use case as well as my
imx8mp-based board.

So lift the private definition of lpddr4_mr_read() from the
imx8mm-cl-iot-gate board code to ddrphy_utils.c, and add a declaration
in the ddr.h header where e.g. get_trained_CDD() is already declared.

This has only been compile-tested for the imx8mm-cl-iot-gate
board (since I don't have the hardware), but since I've merely moved
its definition of lpddr4_mr_read(), I'd be surprised if it changed
anything for that board.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-05-20 09:30:28 +02:00
Marek Vasut
0adf10a87b ARM: dts: stm32: Configure Buck3 voltage per PMIC NVM on Avenger96
The Avenger96 board comes in multiple regulator configurations.
 - rev.100 or rev.200 have Buck3 preconfigured to 3V3 operation on
   boot and contains extra Enpirion EP53A8LQI DCDC converter which
   supplies the IO. Reduce Buck3 voltage to 2V9 to not waste power.
 - rev.200L have Buck3 preconfigured to 1V8 operation and have no
   Enpirion EP53A8LQI DCDC anymore, the IO is supplied from Buck3.

Configure the Buck3 voltage on this board per PMIC NVM settings and
update buck3 voltage limits in DT passed to OS before booting OS to
prevent potential hardware damage.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2022-05-19 18:48:50 +02:00
Neal Frager
6be41ea4e6 arm64: zynqmp: zynqmp-sm-k26-revA: Fix DP PLL configuration
This patch fixes the DP audio and video PLL configurations for the zynqmp-sm-k26-revA som.

The Linux DP driver expects the DP to be using the following PLL config:
  - DP video PLL should use the VPLL (0x0)
  - DP audio PLL should use the RPLL (0x3)
  - DP system time clock PLL should use RPLL (0x3)

Register 0xFD1A0070 configures the DP video PLL.
Register 0xFD1A0074 configures the DP audio PLL.
Register 0xFD1A007C configures the DP system time clock PLL.

Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/fa7e9abc419c9d7648405d1c62367dbe701d09b8.1652709736.git.michal.simek@amd.com
2022-05-18 13:17:54 +02:00
Neal Frager
2946c551f1 arm64: zynqmp: zynqmp-zcu102-revA: Fix DP PLL configuration
This patch fixes the DP audio and video PLL configurations for the
zynqmp-zcu102-revA evaluation board.

The Linux DP driver expects the DP to be using the following PLL config:
  - DP video PLL should use the VPLL (0x0)
  - DP audio PLL should use the RPLL (0x3)

Register 0xFD1A0070 configures the DP video PLL.
Register 0xFD1A0074 configures the DP audio PLL.

Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b2eb87758e0cd4844e1754da8c58fce58d9cf683.1651740949.git.michal.simek@amd.com
2022-05-18 13:17:18 +02:00
Neal Frager
a3659640e0 arm64: zynqmp: zynqmp-zcu106-revA: Fix DP PLL configuration
This patch fixes the DP audio and video PLL configurations
for the zynqmp-zcu106-revA evaluation board.

The Linux DP driver expects the DP to be using the following PLL config:
  - DP video PLL should use the VPLL (0x0)
  - DP audio PLL should use the RPLL (0x3)

Register 0xFD1A0070 configures the DP video PLL.
Register 0xFD1A0074 configures the DP audio PLL.

Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/62538b4a04dee28a6fc8ac5b85f8c845a5a76aa4.1651740988.git.michal.simek@amd.com
2022-05-18 13:17:18 +02:00
Neal Frager
80b8bbbf98 arm64: zynqmp: zynqmp-zcu106-rev1.0: Fix DP PLL configuration
This patch fixes the DP audio and video PLL configurations for the zynqmp-zcu106-rev1.0 evaluation board.

The Linux DP driver expects the DP to be using the following PLL config:
  - DP video PLL should use the VPLL (0x0)
  - DP audio PLL should use the RPLL (0x3)

Register 0xFD1A0070 configures the DP video PLL.
Register 0xFD1A0074 configures the DP audio PLL.

Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ae42ad6185418713a473660c8d15903299af7764.1652192319.git.michal.simek@amd.com
2022-05-18 13:17:18 +02:00
Michal Simek
9c563e916c xilinx: Handle board_get_usable_ram_top(0) properly
board_get_usable_ram_top() was designed for getting the top most location
for U-Boot allocation that's why function itself supports via total_size
parameter to find out where the right location for U-Boot is.
But function itself is also reused by different (EFI) which is passing
total_size as 0 to find out where the usable ram top is. For this case
doesn't make sense (a waste time) to call any lmb functions.
That's why simply return gd->ram_top.

And gd->ram_top is filled already based on previous call for U-Boot iself.
The same solution is also used by stm32mp by commit 92b611e8b0 ("stm32mp:
correctly handle board_get_usable_ram_top(0)") and commit c8510e397f
("stm32mp: Fix board_get_usable_ram_top()").

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/44470619e74f3e480b70deac24578e3e0d5c907e.1651225945.git.michal.simek@amd.com
2022-05-13 09:10:02 +02:00
Tom Rini
21e25992c8 Add new STM32 MCU boards and Documentation
STM32 programmer improvements
 video: support several LTDC HW versions and fix data enable polarity
 board: fix stboard error message, consider USB cable connected when boot device is USB
 configs: stm32mp1: set console variable for extlinux.conf
 configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
 ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
 phy: stm32-usbphyc: Add DT phy tuning support
 arm: dts: stm32mp15: alignment with v5.18
 ram: Conditionally enable ASR
 mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
 configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
 ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
 pinctrl: stm32: rework GPIO holes management
 -----BEGIN PGP SIGNATURE-----
 
 iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmJ6U4QcHHBhdHJpY2Uu
 Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/pg4SEACFSVRcCa/7r2QXObqk
 mORtlp6OrZLfCQGMugv9Oj0W+L4nanJEZEJknhasoHgm5CyTuCGEm7qxgWWBKA9j
 yeCfcpToXrY4cIMgsPR4tpZ9jn4fLsHFBEvCVMEoOp/K2ZI27lfJ0/OeRlgKdg11
 dTmM+J96vw7ltLHeN+yRWY1XgaGsBreqNJSO2mCGrAbbTJXSTrNZxP4wonTvKkFI
 GyTIgRaQA9ggk7/IhalusEEGIF0aaaX/z7uBXqEGkCyOTacLG5rxYNGCoaPdv1Bl
 fT7spZy1bAx3ABq/yJeF38Wi5jCXf55Z3cwYK0+tpJVUlAncYpJJBiyTERtR24OK
 NeDTWkw4e071xPDfmUFB96eINDQ8KXBRRcK2n2b6nW43loYtqgafrx4prL8W2T/u
 mB1WquNwjqdNN43iKAcyArrooOG18sJzRE3uAM6W4fjPx8DAHtYdaO3du3Mb5Kzz
 YaqgVO88NDsYaQRJCnmdQ7KDFToMy5A6btj2LhnYQ/3CMhktkg2RHC0aERGgNJLs
 ifVj3kvc+l8UwomvNOMjNket+AH7hbp64lbAfjAwzcgOGROKNyOslsr33qibg4lQ
 SQKl15wFDHLAcP2tj9QoUFO+97FqDXWBIzoEhDDBqfpVNRx25R7NePUkkA+0dHTS
 VedeNG6p2yFeW2UTAD4nYP9xWA==
 =s7xn
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm

Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
2022-05-10 15:28:02 -04:00
Patrice Chotard
e198d4fe7c doc: Add documentation for STM32 MCUs
Add documentation for STM32 MCUs (F4, F7 and H7 series).

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2022-05-10 13:56:12 +02:00
Patrice Chotard
eda7b6a632 configs: stm32746g-eval: Add stm32746g-eval_spl_defconfig
Add stm32746g-eval_spl_defconfig for stm32746g evaluation board to
build SPL.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2022-05-10 13:56:12 +02:00
Patrice Chotard
e9881a1e75 configs: stm32746g-eval: Add stm32746g-eval_defconfig
Add stm32746g-eval_defconfig for stm32746g evaluation board to
build U-Boot proper.

Full board description can be found here :
https://www.st.com/en/evaluation-tools/stm32746g-eval.html

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2022-05-10 13:56:12 +02:00
Patrice Chotard
16613edbc1 board: stm32f746-disco: Fix dram_init() in none SPL config
Replace CONFIG_SUPPORT_SPL by CONFIG_SPL_BUILD to allow
dram_init() execution when using none SPL defconfig
(stm32f746-disco_defconfig).

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2022-05-10 13:56:12 +02:00
Patrice Chotard
969bc0aece configs: stm32f769-disco: Rename stm32f769-disco_defconfig to stm32f769-disco_spl_defconfig
The current stm32f769-disco_defconfig file supports SPL, rename it to
stm32f769-disco_spl_defconfig to reflect the supported configuration.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2022-05-10 13:56:11 +02:00
Patrice Chotard
0d4ef527da configs: stm32f746-disco: Rename stm32f746-disco_defconfig to stm32f746-disco_spl_defconfig
The current stm32f746-disco_defconfig file supports SPL, rename it to
stm32f746-disco_spl_defconfig to reflect the supported configuration.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2022-05-10 13:56:11 +02:00
Patrice Chotard
67899c2201 board: st: stm32mp1: Consider USB cable connected when boot device is USB
Always consider USB cable is connected when USB boot device is detected.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2022-05-10 13:56:11 +02:00
Patrick Delaunay
1494e37586 board: st: common: fix the error messages in stboard command
Add missing \n at the end of the error trace

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
2022-05-10 10:56:39 +02:00
Pali Rohár
c7484ce091 Nokia RX-51: Convert to CONFIG_DM_SERIAL
For CONFIG_DM_SERIAL it is required to increase CONFIG_SYS_MALLOC_F_LEN as
default value is not enough for memory hungry CONFIG_DM_SERIAL code.

Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
2022-05-09 13:40:24 -04:00
Gireesh Hiremath
655a93f079 am335x, guardian: Drop non DM_I2C code
On this platform DM_I2C and SPL_DM_I2C enabled.
Remove legacy code.

Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2022-05-09 13:40:24 -04:00
Masami Hiramatsu
55a8bb94f9 board: synquacer: developerbox: Remove Masami from MAINTAINERS
Remove Masami Hiramatsu from MAINTAINERS since he will leave
Linaro and his email will be not available anymore.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
2022-05-05 09:28:48 -04:00
Jim Liu
84335544ea arm: nuvoton: Add support for Nuvoton NPCM750 BMC
Add basic support for the Nuvoton NPCM750 EVB (Poleg).

Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
2022-05-05 09:28:47 -04:00
Marek Behún
0ce0feb046 arm: mvebu: turris_mox: Use DM registered MDIO
In order to be able to get rid of the non-DM MDIO bus registered in
mvneta driver, start using the DM registered one in Turris MOX board
code.

This also allows us to drop the hack introduced in MOX' -u-boot.dtsi
file.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Marek Behún
a2b2542992 arm: mvebu: Espressobin: Use DM registered MDIO to configure switch
In order to be able to get rid of the non-DM MDIO bus registered in
mvneta driver, we need to stop using board_network_enable() and instead
use the DM registered MDIO device to configure switch in
last_stage_init().

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Stefan Roese
1770808199 mips: octeon: nic23: Enable ethernet support
This patch enables the Kconfig symbols needed for full ethernet support
on the NIC23. Additionally board specific setup is done, mostly GPIOs
related to SFP / GPIO configuration. With this, ethernet can be used on
this board. Here an example of a tftp load:

=> tftp ffffffff81000000 big
Using ethernet-mac-nexus@11800e2000000 device
TFTP from server 192.168.1.5; our IP address is 192.168.1.247
Filename 'big'.
Load address: 0xffffffff81000000
Loading: ##################################################  10 MiB
         9.7 MiB/s
done
Bytes transferred = 10485760 (a00000 hex)

Signed-off-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Tom Rini
edb6982b58 Merge branch '2022-05-02-add-verifying-program-loader'
To quote the author:

U-Boot provides a verified-boot feature based around FIT, but there is
no standard way of implementing it for a board. At present the various
required pieces must be built up separately, to produce a working
implementation. In particular, there is no built-in support for selecting
A/B boot or recovery mode.

This series introduces VPL, a verified program loader phase for U-Boot.
Its purpose is to run the verified-boot process and decide which SPL
binary should be run. It is critical that this decision happens before
SPL runs, since SPL sets up SDRAM and we need to be able to update the
SDRAM-init code in the field.

Adding VPL into the boot flow provides a standard place to implement
verified boot. This series includes the phase itself, some useful Kconfig
options and a sandbox_vpl build for sandbox. No verfied-boot support is
provided in this series.

Most of the patches in this series are fixes and improvements to docs and
various Kconfig conditions for SPL.
2022-05-02 19:02:44 -04:00
Simon Glass
9ae25b9ac9 sandbox: Add a build for VPL
Add an initial VPL build for sandbox. This includes the flow:

   TPL (with of-platdata) -> VPL -> SPL -> U-Boot

To run it:

   ./tpl/u-boot-tpl -D

The -D is needed to get the default device tree, which includes the serial
console info.

Add a Makefile check for OF_HOSTFILE which is the option that enables
devicetree control on sandbox.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-05-02 09:58:13 -04:00
Chris Packham
08dc62c152 ARM: mvebu: x530: set MPP55 to gpio
MPP55 is used as a reset connected to the L3 switch chip. This doesn't
matter for u-boot as it doesn't use the L3 switch but it is useful to
be able to toggle the switch in/out of reset for the OS.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-02 07:47:26 +02:00
Pali Rohár
363d9f2c2f arm: mvebu: turris_omnia: Fix SYS_RSTOUT_* macro names
This is A385 register.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-02 07:47:26 +02:00
Tony Dinh
dbd2a382c1 arm: kirkwood: nsa310s: Use Marvell uclass mvgbe and PHY driver for DM Ethernet
The Zyxel NSA310s board has the network chip Marvell Alaska 88E1318S.
Use uclass mvgbe and the compatible driver M88E1310 driver to bring
up Ethernet.

- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Remove CONFIG_RESET_PHY_R.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add phy mode RGMII to kirkwood-nsa310s.dts
- Miscellaneous changes: Move constants to .c file and remove header file
board/zyxel/nsa310s/nsa310s.h, add support for large USB and SATA HDDs,
use BIT macro, add/cleanup comments, and cosmetic changes.

Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220412201820.10291-1-mibodhi@gmail.com/

Signed-off-by: Tony Dinh <mibodhi@gmail.com>
2022-05-02 07:47:26 +02:00
Pali Rohár
1ae8a5fb6a arm: mvebu: turris_omnia: Fix RESET button message
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
2022-05-02 07:29:55 +02:00
Pali Rohár
73c7db73e8 arm: mvebu: turris_omnia: Add support for USB3.0 mode in WWAN MiniPCIe slot
PCIe Mini CEM 2.1 spec added support for USB3.0 mode on MiniPCIe cards.
USB3.0 and PCIe share same pins and only one function can be active at the
same time. PCIe Mini CEM 2.1 spec says that determining function is
platform specific and spec does not define any dedicated pin which could
say if card is USB3.0-based or PCIe-based.

Implement this platform specific decision (USB3.0 vs PCIe) for WWAN
MiniPCIe slot on Turris Omnia via U-Boot env variable "omnia_wwan_slot",
similarly like is implemented forced mode for MiniPCIe/mSATA slot via
"omnia_msata_slot" env variable. Value "usb3" for "omnia_wwan_slot" would
mean to set USB3.0 mode and value "pcie" original PCIe mode.

A385 SoC on Turris Omnia has configurable fifth SerDes line (exported to
MiniPCIe WWAN slot with SIM card) either to USB3.0 or PCIe functionality,
so implementation of this new PCIe Mini CEM 2.1 feature is simple, by just
configuring SerDes to USB 3.0 mode.

Other twos MiniPCIe slots on Turris Omnia do not have this new
functionality as their SerDes lines cannot be switched to USB3.0
functionality.

Note that A385 SoC does not have too many USB3.0 blocks, so activating
USB3.0 in MiniPCIe cause that one external USB3.0 USB-A port would loose
USB3.0 functionality and would be downgraded just to USB2.0.

By default this MiniPCIe WWAN slot is in PCIe mode, like before.

To set this MiniPCIe WWAN slot to USB3.0 mode, call U-Boot commands:

  => setenv omnia_wwan_slot usb3
  => saveenv
  => reset

Signed-off-by: Pali Rohár <pali@kernel.org>
2022-05-02 07:28:25 +02:00
Pali Rohár
72a9dd264c arm: mvebu: turris_omnia: Signal error when sata/pcie DT mode
Show error message when DT file does not contain sata or pcie node which
should be explicitly disabled. This can happen when U-Boot code for finding
those nodes is incomplete or when those DT nodes are in different
unexpected location. In any case it is needed to know if DT not was not
explicitly disabled as it could mean that combo slots where setup
incorrectly.

Signed-off-by: Pali Rohár <pali@kernel.org>
2022-05-02 07:28:25 +02:00
Pali Rohár
d80276870d arm: mvebu: turris_omnia: Extract code for disabling sata/pcie
Move code for disabling sata and pcie DT nodes to own functions, so this
code can be called from other places in follow up patches.

Signed-off-by: Pali Rohár <pali@kernel.org>
2022-05-02 07:28:25 +02:00
Pali Rohár
1da19dcf3b arm: mvebu: turris_omnia: Allow to configure mSATA slot via env variable
Some PCIe-based MiniPCIe cards are broken and they do not ground PIN 43
which is required by PCIe mini CEM specs. Such broken cards are incorrectly
detected as mSATA cards because SATA specs requires that PIN 43 on mSATA
cards has to be disconnected.

PIN 43 on Turris Omnia is used only for MiniPCIe/mSATA card detection by
software in U-Boot SPL. Allow to override that U-Boot SPL detection by a
new "omnia_msata_slot" env variable (to value "pcie" or "sata") so broken
MiniPCIe cards can be used in combo mSATA/MiniPCIe slot too.

As configuration of PCIe vs SATA functionality is done in U-Boot SPL,
it is required to change env variable in permanent storage and reset the
board to take effect.

To force PCIe mode for broken MiniPCIe cards, call U-Boot commands:

  => setenv omnia_msata_slot pcie
  => saveenv
  => reset

Signed-off-by: Pali Rohár <pali@kernel.org>
2022-05-02 07:28:25 +02:00
Pali Rohár
8ead243ecc arm: mvebu: turris_omnia: Define only one serdes map variable
By default use primary serdes map with PCIe function in combined
miniPCIe/mSATA slot. When SATA is detected change serdes map variable at
runtime.

Signed-off-by: Pali Rohár <pali@kernel.org>
2022-05-02 07:28:25 +02:00
Pali Rohár
d6ba5c4f92 arm: mvebu: turris_omnia: Provide env_sf_get_env_addr() function
BootROM maps SPI Flash to fixed address 0xD4000000 and this mapping is
active also when BootROM is executing binary kwbimage headers, which
includes also U-Boot SPL.

Therefore no initialization code is required to access SPI Flags from
U-Boot SPL. In proper U-Boot it is remapped to other location.

So in mvebu implementation of env_sf_get_env_addr() function returns
0xD4000000 when running in SPL and NULL when in proper U-Boot.

This change would allow to use U-Boot ENV in U-Boot SPL. Normally it is not
possible to read ENV because it is too big and U-Boot SPL does not have
such big malloc() pool to real all ENV variables.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
2022-05-02 07:28:25 +02:00
Marek Vasut
69245e406e led: Drop led_default_state()
This function is empty, drop it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2022-04-28 09:26:44 -04:00
Tom Rini
8b2b125e95 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx
fsl-qoriq: Fixes and updates on fsl-layerscape
mpc85xx: fixes and code cleanup
2022-04-27 09:19:41 -04:00
Sean Anderson
7026c1ee70 board: ls1046afrwy: Remove Manish Tomar's email
Manish Tomar's email bounces. Remove it, and reassign the config he was
maintaining to the primary maintainer for the board.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
71dcf8128c board: freescale: p1_p2_rdb_pc: Move ifdef for USB/eLBC check to correct place
Whole section about USB/eLBC configuration seems to be P1020 specific. So
add ifdefs to not compile it on other platforms (e.g. P2020).

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
0b30cb3de7 board: freescale: p1_p2_rdb_pc: Fix page attributes for second 1G SDRAM map
Like for first 1G SDRAM map, do not enable Caching-inhibited nor Guarded
attribute for second 1G SDRAM mapping. Whole 2G SDRAM should use caches and
also allow speculative loading (by not setting Guarded attribute).

Also enable Memory Coherency attribute for second 1G SDRAM map. In commit
316f0d0f8f ("powerpc: mpc85xx: Fix static TLB table for SDRAM") it was
enabled for all SDRAM maps on all other boards, just missed this one case.

As a last thing, first 1G SDRAM map has wrong comment, so adjust it.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
0992c2be77 board: freescale: p1_p2_rdb_pc: Do not set MPC85xx_PMUXCR_SDHC_WP bit when SDHC_WP is used as GPIO
When MPC85xx_PMUXCR_SDHC_WP is set then SDHC controller automatically makes
inserted SD card readonly if GPIO[9] is active.

In some design GPIO[9] pin does not have to be connected to SD card
write-protect pin and can be used as GPIO.

So do not set MPC85xx_PMUXCR_SDHC_WP bit when GPIO[9] is not used for
SDHC_WP functionality.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
4aceaec585 board: freescale: p1_p2_rdb_pc: Detect both P2020 SD switch configurations
As written in comment, P2020 has two possible SD switch configurations.
Extend code to detect both of them.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
ccad59dc5c board: freescale: p1_p2_rdb_pc: Do not hang in checkboard()
Like in all other checks in checkboard() function, do not hang on error.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
03edf23376 board: freescale: p1_p2_rdb_pc: Allow to compile it without env support
When env support is disabled then usage of env_init() or env_relocate()
generates linker errors. So do not compile env_init() or env_relocate()
in SPL code when env support is disabled in SPL.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Michael Walle
20759b2973 board: sl28: add basic PSCI implementation
For now, this only provides reset and poweroff functions.

Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:13:57 +05:30
Michael Walle
49bb245f1d armv8: psci: add ARMV8_PSCI_RELOCATE Kconfig option
There is an user-selectable SYS_HAS_ARMV8_SECURE_BASE, which has the
same meaning but is just for the ls1043ardb board. As no in-tree config
uses this, drop it and replace it with something more sophiticated:
ARMV8_PSCI_RELOCATE. This option will then enable the ARMV8_SECURE_BASE
option which is used as the base to relocate the PSCI code (or any code
in the secure region, but that is only PSCI). A SoC (or board) can now
opt-in into having such a secure region by enabling
SYS_HAS_ARMV8_SECURE_BASE. Enable it for the LS1043A SoC, where it was
possible to relocate the PSCI code before as well as on the LS1028A SoC
where there will be PSCI support soon.

Additionally, make ARMV8_PSCI and SEC_FIRMWARE_ARMV8_PSCI exclusive.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:13:57 +05:30
Durai Manickam KR
c8532d3f9e configs: Add sam9x60_curiosity_mmc_defconfig
Add boot from SDMMC (sdcard) support for sam9x60_curiosity.

Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
2022-04-26 09:50:24 +03:00
Durai Manickam KR
b07a022964 board: Add sam9x60_curiosity support
Add board files, Kconfig, Makefile and MAINTAINERS.

Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
2022-04-26 09:50:24 +03:00
Tom Rini
11232139e3 nds32: Remove the architecture
As removal of nds32 has been ack'd for the Linux kernel, remove support
here as well.

Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
2022-04-25 16:04:05 -04:00
Tom Rini
6e2af641e4 u-boot-imx-20220422
-------------------
 
 - Switch to DM_SERIAL
 - Drop MMCROOT
 - several cleanup
 
 CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/11815
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCYmJq1Q8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76ZlxQCfQNPkQVf10kjENID/D9mu+Hl2tMEAnj8AMOyF
 iQrcw6oegrVvZZXV+s2J
 =XjAE
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20220422' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20220422
-------------------

- Switch to DM_SERIAL
- Drop MMCROOT
- several cleanup

CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/11815
2022-04-22 08:12:20 -04:00
Ying-Chun Liu (PaulLiu)
84adf92968 imx8mm-cl-iot-gate: Remove redundant board_fix_fdt()
In arch/arm/mach-imx/imx8m/soc.c there's an implementation of
board_fix_fdt() introduced by commit 35bb60787b. Remove the
redundant one to avoid failed to build from source when enabling
CONFIG_OF_BOARD_FIXUP.

Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-04-21 23:00:26 +02:00
Peng Fan
151a030063 arm: set cntfrq_el0 if CONFIG_COUNTER_FREQUENCY is valid
Since COUNTER_FREQUENCY is obselete, so set cntfrq_el0 if
CONFIG_COUNTER_FREQUENCY is valid

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
2022-04-21 15:27:18 -04:00
Peng Fan
d8c033a9cd xilinx: versal: board: use CONFIG_COUNTER_FREQUENCY
Since versal has CONFIG_COUNTER_FREQUENCY, so use it. And
COUNTER_FREQUENCY will be dropped.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2022-04-21 14:32:40 -04:00
Tom Rini
e50f66e364 Merge https://source.denx.de/u-boot/custodians/u-boot-marvell
- mrvl_uart.sh: Remove script (Pali)
- Fix Espressobin build for configs where ENV is not in SPI (Rogier)
- mvebu: a37xx: Add support for reading OTP (Pali)
- mvebu: uDPU: Ethernet fixes and misc DT and defconfig changes (Robert)
- mvebu: Add support for reading LD0 and LD1 eFuse (Pali)
- kwboot: Replace fstat()+st_size by lseek()+SEEK_END (Pali)
- mvebu: turris_omnia: Enable CONFIG_CMD_FUSE (Pali)
- arm: Add CONFIG_SPL_SYS_NO_VECTOR_TABLE used on 32bit MVEBU (Pali)
- mvebu: a37xx: Add support for writing Security OTP values (Pali)
- mvebu: turris: Misc enhancements and cleanups / fixes (Pali)
- Sheevaplug : Use Marvell uclass mvgbe and PHY driver for Ethernet (Tony)
2022-04-21 11:44:54 -04:00
Michael Trimarchi
0016e62813 board: bsh: imx8mn_bsh_smm_s2/s2pro: enable DM_SERIAL
Enable DM_SERIAL for both U_Boot and the SPL. The uart4 and its pinmux
are already marked with u-boot,dm-spl but we need to move the call to
preloader_console_init() after spl_init() to avoid a board hang
as dm can't be used until after spl_init().

Remove the manual config of the UART pinmux now that it is no longer
needed.

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
2022-04-21 15:18:25 +02:00
Peng Fan
a497740f4e imx: imx8mn_evk: enable CONFIG_DM_SERIAL
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.

move the preloader_console_init() call after spl_init() to
avoid board hang

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-21 15:18:25 +02:00
Peng Fan
bf6e0b9fd2 imx: imx8mm_evk: enable CONFIG_DM_SERIAL
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.

move the preloader_console_init() call after spl_early_init() to
avoid board hang

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-21 15:18:25 +02:00
Peng Fan
ae188eb61c imx: imx8mp_evk: enable CONFIG_DM_SERIAL
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-21 15:18:25 +02:00
Paul Barker
a95cd68d51 board: ti: am335x: Add support for BBE Extended WiFi
The Sancloud BeagleBone Enhanced Extended WiFi (BBE Extended WiFi) has
its own devicetree file and the board can be identified by the 2nd
letter of the config string within the common EEPROM.

Signed-off-by: Paul Barker <paul.barker@sancloud.com>
2022-04-21 09:08:57 -04:00
Paul Barker
cde726442b board: ti: am335x: Add BBE Lite support
The Sancloud BeagleBone Enhanced Lite (BBE Lite) has its own devicetree
file and the board can be identified by the 2nd letter of the config
string within the common EEPROM.

Signed-off-by: Paul Barker <paul.barker@sancloud.com>
2022-04-21 09:08:57 -04:00
Tony Dinh
ac47bd230c arm: kirkwood: Sheevaplug : Use Marvell uclass mvgbe and PHY driver for Ethernet
The Globalscale Technologies Sheevaplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.

- Remove CONFIG_RESET_PHY_R symbol from all board files
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/sheevaplug/sheevaplug.h, use BIT macro, and add/cleanup
comments.

Signed-off-by: Tony Dinh <mibodhi@gmail.com>
2022-04-21 13:14:52 +02:00
Marcel Ziswiler
fc102c87c1 board: toradex: drop colibri pxa270 support
The Colibri PXA270 has been end-of-life since quite a while and would
require more and more maintenance (e.g. DM conversions).

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-04-21 12:48:30 +02:00
Tim Harvey
2395625209 board: gateworks: venice: add imx8mp-venice-gw740x support
The GW74xx is based on the i.MX 8M Plus SoC featuring:
 - LPDDR4 DRAM
 - eMMC FLASH
 - Gateworks System Controller
 - PCIe Gen 3.0 switch (build option)
 - USB 3.0 HUB
 - USB Type-C front panel connector
 - GPS
 - 3-axis accelerometer
 - CAN bus
 - 6x GbE RJ45 front-panel jacks
  - 1x IMX8M FEC RGMII GbE (with Passive PoE)
  - 5x IMX8M EQOS RGMII 6 port GbE Switch
    (1x with 802.3af class 5 Active PoE)
 - RS232/RS485/RS422 serial transceiver
 - MIPI header (DSI/CSI/GPIO/PWM/I2S)
 - DigI/O header (UART/GPIO/I2C/ADC)
 - 802.11ac WiFi
 - Bluetooth BLE
 - 3x MiniPCIe sockets with PCI/USB
 - 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
 - PMIC
 - Wide range DC input supply (8V to 60V DC)

Do the following to add support for this and future imx8mp-venice boards:
 - add dts
 - add DRAM config
 - add PMIC config
 - add IMX8MP support in spl.c and venice.c

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-04-21 12:44:24 +02:00
Tim Harvey
93de85c9d7 board: gateworks: venice: add additional levels for dtb name match
Gateworks produces many products from a single PCB with subloaded
components. Add an additional two levels of dtb name matching so that
for example a GW7400-A matches the dtb name of gw74xx.dtb

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-04-21 12:44:24 +02:00
Tim Harvey
61cf225053 board: gateworks: gw_ventana: use comomn GSC driver
Use the common GSC driver.

This allows us to do some additional cleanup:
 - use the GSC driver functions
 - move waiting for the EEPROM to the SPL int (it will always be ready
   after this)
 - move eeprom functions into eeprom file and elimate GSC_I2C_BUS
 - eliminate some redundant EEPROM reads (the EEPROM must be read in
   SPL before relocation, in SPL after relocation, and in U-Boot init.
   All subsequent uses can use the global structure)
 - remove unnecessary header files and alphabatize includes

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-04-21 12:44:24 +02:00
Tim Harvey
fb9ec33878 board: gateworks: venice: use common GSC driver
Use the common GSC driver.

This allows us to do some additional cleanup:
 - rename gsc{.c,.h} to eeprom{.c.h} for clarity
 - collapse eeprom_get_dev
 - remove unnecessary header files and alphabatize includes

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-04-21 12:44:23 +02:00
Marcel Ziswiler
405c97fd1d configs: tdx: apalis_imx6: drop hw v1.0 support
Drop optional support for the ancient Apalis iMX6 V1.0 hardware which
had the UART wired as DCE rather than DTE.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-04-21 12:44:23 +02:00
Marcel Ziswiler
4625ff6521 board: colibri_imx7: fix usb start on solo
This fixes the following crash when run on a Colibri iMX7S aka solo:

Colibri iMX7 # usb start
starting USB...
Bus usb@30b10000: USB EHCI 1.00
Bus usb@30b20000:

The i.MX 7Solo has only one single USB OTG1 but no USB host port. Trying
to initialize the nonexisting port just crashes.

While at it also drop board_usb_phy_mode() which is also no longer used
in the driver model age.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-04-21 12:44:23 +02:00
Denys Drozdov
47bcc0d056 toradex: apalis-imx8x: drop support for apalis imx8x
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.

Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-04-21 12:44:23 +02:00
Pali Rohár
08b99b6775 board: turris: Rename atsha204a@64 DT node to crypto@64
DT node name should be generic, therefore rename atsha204a@64 to crypto@64.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
2022-04-21 12:31:36 +02:00
Pali Rohár
98bbb6e7ab board: turris: Allow to specify first eth idx of first MAC address
Turris Omnia uses first MAC address from OTP for second ethernet interface.
Second MAC address for third interface and third MAC address for first
interface.

Other Turris routers do not have this rotate by one mapping. So add
function parameter for specifying id of the first ethernet interface.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
2022-04-21 12:31:36 +02:00
Pali Rohár
ada791db3e board: turris: Do not cache Atsha device in BSS
Atsha device is used prior relocation and at this early stage BSS does not
have to be ready yet. So do not cache Atsha device in BSS.

Fixes support for other Turris routers.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
2022-04-21 12:31:36 +02:00
Pali Rohár
6ac08dc1a8 board: turris: Move Turris Atsha OTP code to separate file
OTP code is not Atsha generic but also it is not Omnia specific. It is
common for all Turris routers which use Atsha cryptochip for storing OTP.
So move this common Turris specific Atsha OTP code from Turris Omnia into
separate file. It will be used also by other Turris routers.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
2022-04-21 12:31:36 +02:00
Pali Rohár
85df8f9a21 arm: mvebu: a37xx: Extend mbox_do_cmd() code
Allow to specify input parameters, define all available mbox commands
supported by CZ.NIC's secure firmware and also Marvell's fuse.bin firmware
and fix parsing response from Marvell OTP commands.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-04-21 12:31:36 +02:00
Pali Rohár
46ce9c78a9 arm: mvebu: a37xx: Move generic mbox code to arch/arm/mach-mvebu
Generic A3720 mbox code is currently in Turris Mox specific board file
board/CZ.NIC/turris_mox/mox_sp.c. Move it to board independent arch file
arch/arm/mach-mvebu/armada3700/mbox.c.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-04-21 12:31:36 +02:00
Rogier Stam
a37b68820c arm: mvebu: Fix Espressobin build for configs where ENV is not in SPI
When storing the UBoot Environment in for example EXT4,
the U-Boot build is broken for several reasons:
1. armada-385-turris-omnia-u-boot.dtsi will not allow
   CONFIG_ENV_OFFSET and CONFIG_ENV_SIZE to be undefined
2. armada-37xx/board.c ft_board_setup function does not
   exist if CONFIG_ENV_IS_IN_SPI_FLASH is not defined

This commit changes these files so that selecting a
different location for the environment is possible.

Signed-off-by: Rogier Stam <rogier@unrailed.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
2022-04-21 12:31:26 +02:00
Tom Rini
24c904f309 Convert CONFIG_SYS_MEM_TOP_HIDE to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_MEM_TOP_HIDE

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-19 14:52:34 -04:00
Michal Simek
fcbdd7a070 .mailmap: Start to use new amd.com email address
Xilinx has been acquired by AMD that's why emails should be also updated.
The patch is updating .mailmap file and also MAINTAINERS files as was done
by commit 5cd1ecb994 ("ppc: qemu: Update MAINTAINERS for correct email
address").
The rest of my emails are not going to change.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
2022-04-19 14:51:11 -04:00
Johan Jonker
8f47414466 board: rk3288: add more DT files to MAINTAINERS
A number of rk3229/rk3288 DT files are synced from Linux.
Add a maintainer to look after them and to help with
review and testing.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Johan Jonker
8042717afa board: google: veyron: add more DT files to MAINTAINERS
The Google Veyron rk3288 DT files are synced from Linux.
Add a maintainer to look after them and to help with
review and testing.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Johan Jonker
62fcd72ef2 rockchip: rk3066: add Rikomagic MK808 board
MK808 is a RK3066-based board with 1 USB host and 1 USB OTG port,
HDMI and a micro-SD card slot. It also includes on-board NAND
and 1GB of SDRAM.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Tom Rini
9859465bfe Pull request for efi-2022-07-rc1-2
Documentation:
 
 * Describe env command
 
 UEFI
 
 * simplify Unicode string functions
 * clean up the usage of GUIDs for capsule updates
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAmJZTvsACgkQxIHbvCwF
 GsTbOg//XtOKXKHsWIq0cDgxxUTM2iSWCwzw2rSO3VPbzjeRekBCH3+I6D6hCHmp
 ikSPB8LBRRMEkBPq18LdXY9oaV6keRGgLNtiLATKLMHsJ9USkCqNzdSegCIWFl0T
 2N5Rm/qdh90csGyIzEk+qPOLBNP/St/aTO6n7b9+FgZ6Hy2dwXTjnNzPFEnz3hCY
 KjlOxIWsgofb9Iem4f+mMhgiBjM161yqWMd2ND/EDn3RRjrAh/ZWRcD/nWirZxeO
 uwn+8bMjDfO83yICS1txp6mbvtFHhrktSo6hc7Ga5m+5kmlPBcgKnKEIUgrKuNd/
 Jyr12MLBtI7oyETr+CY9vPQTciWBU17cW2TO7CIBDQt3QtfvVBrWaGe4barPLPzx
 hvyKzrflRDTFUKoG+f/XGN2YSvYw+QXVXZjBqYDwOepT7oq6lWpf7gtxNQNG5RZI
 uOwk95VT/cVh7S8qp1ioD+tGtvA9PeMyuh8mryD2kYrJh4bbGimfyP2Z6e/aIRNi
 RnczTAFDXoA4g32DP8/3Im43rSIv685e4N0YnDF+ZyKALxyflZAPXT0MY8FLfGyE
 x6Zb1t45W8thIDhBLNjurBge4NTFuCq0NM8mszOHMFBgO7PDIMEX+9uZOvhrhYbs
 a7XYFIEIcZZiLqkNjwr7B+D7Ya6q7gYvcqAo6rgtbDNs5QpH/0A=
 =UQMn
 -----END PGP SIGNATURE-----

Merge tag 'efi-2022-07-rc1-2' of https://source.denx.de/u-boot/custodians/u-boot-efi

Pull request for efi-2022-07-rc1-2

Documentation:

* Describe env command

UEFI

* simplify Unicode string functions
* clean up the usage of GUIDs for capsule updates
2022-04-15 14:29:52 -04:00
Tom Rini
7f418ea598 Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net
- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.

[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]
2022-04-15 08:10:32 -04:00
Sughosh Ganu
741ef86728 capsule: board: Add information needed for capsule updates
Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
2022-04-15 10:43:18 +02:00
Tim Harvey
a1c711046b board: gateworks: venice: add imx8mm-gw7903 support
The GW7903 is based on the i.MX 8M Mini SoC featuring:
 - LPDDR4 DRAM
 - eMMC FLASH
 - microSD socket with voltage select support
 - Gateworks System Controller
 - M.2 A-E Socket with USB2.0 and PCIe
 - MiniPCIe Socket with PCIe, USB2.0, and SIM
 - IMX8M FEC
 - RS232/RS485/RS422 serial transceiver
 - LIS2DE12 3-axis accelerometer
 - front panel LED's
 - off-board isolated digital I/O
 - Wide range DC power input
 - 802.3at PoE
 - PMIC

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-04-13 09:55:26 +02:00